TECHNICAL DOCUMENTATION

SSP 337 The 2,0l FSI engine with turbocharger

PDFEN28 pages2 MB
SSP 337 The 2,0l FSI engine with turbocharger - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingSelf-study programme 337The 2.0l FSI engine with turbochargerDesign and function The new FSI engines from Volkswagen do without stratified injection and place greater emphasis on output and torque. Until now, FSI direct injection was always associated with stratification. On the turbocharged engine, the abbreviation FSI remains but there is no stratified charge. Doing without fuel stratification and NOx sensors represents a loss on one part, but also promises the finest driving enjoyment with high output and a torquey engine and great pulling power and economy. In this self-study programme you can familiarize yourself with the technical highlights of this engine.Further information can be found in self-study programme no. 322 The 2.0l FSI engine with 4-valve technology.S337_002NEWWarning NoteThe self-study programme shows the design and function of new developments. The contents will not be updated.For instructions on testing, adjusting and repairs, please refer to the relevant service literature.2 At a glanceIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Engine mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Engine management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24Test your knowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 263 IntroductionDescription of the engineIn terms of basic dimensions and design, the turbo FSI engine is derived from the 2.0l FSI with engine code AXW. In order to meet the high expectations of a turbocharged engine, components of the engine had to be adapted to specific requirements.The exhaust manifold and the turbocharger form one unit. The exhaust and turbo module is customer service friendly and is attached to the cylinder head by a clamping flange.Exhaust manifoldSolenoid valve for charge pressure control N75TurbochargerResonance silencerTurbocharger air recirculation valve N249S337_003The crankshaft mechanics have been adapted to the higher demands of a turbocharged FSI engine.Piston Conrod CrankshaftS337_0044 In order to meet the higher levels of power and heat transfer, the cylinder head has been adapted to the specific conditions. The inlet camshaft features continuously variable valve timing (adjustment range 42° crankshaft angle).Cylinder headInlet portsS337_005The optimised balancer shaft gear (AGW) is driven by a decoupled drive chain sprocket. The function is similar to that of a dual mass flywheel.Decoupled drive chain sprocket Balancer shaft gearS337_0065 Engine mechanicsTechnical dataThe 2.0l turbocharged FSI engine was first installed in the Audi A3 Sportback. At Volkswagen, the engine finds its debut in the Golf GTI.Technical features - Turbocharger in exhaust manifold - Single pipe exhaust system with starter and underbody catalyst close to engine - Hitachi high pressure pump resistant to ethanol - Non-return fuel system - Homogenous fuel injectionTechnical dataEngine code Engine type Capacity [mm3] Bore [mm] Stroke [mm] Compression ratio Max. output Max. torque Engine management Variable valve timing Exhaust gas recirculation Fuel AXX 4-cylinder in-line engine 1984 82.5 92.8 10.5:1 147 kW at 5700 rpm 280 Nm at 1800-4700 rpm Bosch Motronic MED 9.1 42° crankshaft angle Inner exhaust gas recirculation Premium unleaded RON 98 (normal unleaded RON 95 with reduced performance) 2 three-way catalytic converters with lambda control EU 4Speed [rpm] Torque [Nm] Output [kW]S337_007Torque and performance graphExhaust gas treatmentEmissions standardS337_0086 The crankshaftThe component strength was adapted to the higher combustion pressures. The contact faces of the main journals and conrod journals were made larger to improve strength.Engine block The cylinder contact surfaces of the cast iron engine block were honed by means of liquid blasting. Liquid blasting and smooth honing are an extension of the familiar two-stage honing technique by two additional process stages. In the first new processing stage, any compacting of the bushing contact surface brought about from the high pressure procedure is removed, and scores and damage from honing and cracks from alloying are rectified. The resulting surface is thereby largely free of metallic imperfections. In the final honing operation, the rough edges arising from blasting and any remaining rough areas are smoothed out to the highest level. This type of honing shortens the running-in time of the engine and leads to lower oil consumption.Contact facesS337_009S337_010Modified pistons The piston crown of the T-FSI has been adapted to the homogenous combustion procedure.2.0l 4V FSI2.0l 4V T-FSIS337_0117 Engine mechanicsThe balancer shaft gearThe balancer shaft gear was taken over from the common FSI engine. However, it had to be modified as follows:●CrankshaftDrive gearBalancer wheels Balancer shaft housing●● ●● ●Decoupled drive chain sprocket in balancer shaft mechanism Separation of splines and compensation weights to increase balancing efficiency Oil pump with greater gear width Pressure relief valve, controlled purely by oil, with oil control in vicinity of oil pump, integrated in balancer shaft housing Strength optimised pressure cast housing Bearings of balancer shafts located directly in aluminium housingBalancer shaftsSuction lineDrive chain sprocketOil pumpS337_012The decoupled drive chain sprocketThe improved smooth running of the crankshaft in the lower speed range leads to a considerable increase in chain forces in the balancer shaft gear. With a relative crankshaft vibration angle of 0.8° on the normal FSI engine, the increased crankshaft vibration angle of 2° on the turbocharged FSI engine is much more noticeable. Due to the increased load of the chain drive, the chain would be subjected to increased wear if there were no countermeasures. Therefore, there are curved springs in the hub of the chain sprocket. These decouple the input shaft of the balancer shaft gear to the crankshaft.Diamond washerHub Friction bearing Curved springs (qty. 2)Chain sprocket Friction washer Dished washer End washerS337_0138 The toothed belt drive mechanismAs with all 4-cylinder in-line engines of series 113, the valve timing is designed as a toothed belt and direct exhaust camshaft drive system. Due to considerably higher demands on the toothed belt drive mechanism, such as:● ●Function The positioning of the toothed belt on the crankshaft is shown at TDC no. 1 cylinder, as in illustration 337_014. Once the working stroke begins, extremely high pulling forces are imparted on the toothed belt. These are reduced by the elliptical shape of the toothed belt pulley, due to the fact that the flat side of the pulley allows slight detensioning of the toothed belt. The rotational vibrations that arise as a result counteract the rotational vibrations of the 2nd engine order in the resonance point of the timing mechanism, without causing excessive unrest in other speed ranges.●higher valve spring forces due to turbo turbo-specific timing in conjunction with adjustment range of 42° CA from continuously variable valve timing (inlet camshaft). high pressure pump drive by means of 3 cams on inlet camshaft,the toothed belt tensioning system, adopted from the naturally aspirated engine, was modified. This resulted in an elliptical toothed belt pulley on the crankshaft. The CTC toothed belt pulley*, used for the first time, reduces rotational vibrations on the camshaft and pulling forces on the toothed belt.* CTC toothed belt pulley = Crankshaft Torsionals CancellationS337_0149 Engine mechanicsThe cylinder headTurbo-specific changes were made to the cylinder head (with regards to the 2.0l FSI):● ● ●●Sodium filled exhaust valves Armoured inlet and exhaust valve seats Strength-optimised roller rocker fingers with reduction in web width from cams and rollers Valve springs with increased spring forces (same valve springs for inlet and exhaust valves)Furthermore, the inlet port geometry was modified. This enabled the tumble effect and thereby the knock resistance and smooth running properties to be improved.2.0l 4V FSI2.0l 4V T-FSIS337_015S337_01610 The crankcase breather systemThe constant vacuum in the crankcase is assured by a separate breather system for crankcase and cylinder head. The blow-by gases emerging from the crankcase are passed via the primary oil separator in the oil filter module to the cylinder head cover. When this happens, the blow-by gases are mixed with those from the cylinder head and are passed through a labyrinth, where further oil separation occurs. Since turbo operation requires more complicated pressure control, there is a two-stage pressure relief valve on the cylinder head cover, which channels the blow-by gases to the intake manifold or turbocharger. When there is vacuum in the intake manifold, the blow-by gases are fed directly to the intake manifold. In the case of charge pressure, a non-return valve closes in the pressure relief valve housing. The blow-by gases are fed to the turbocharger via a channel in the cylinder head cover. To recognize an incorrectly installed pressure relief valve, a so-called diagnosis port has been integrated. Incorrect installation forces unmetered air via the sealing area of the pressure relief valve into the cylinder head cover. The reaction of the lambda probe results in diagnosis of the unmetered air and a fault is then stored in the memory.With charge pressure before turbocharger With vacuum to intake manifoldGas outlet to turbochargerLabyrinth in cylinder head coverGas outlet to intake manifoldPrimary oil separator Oil filter module Non-return locking valve Non-return locking valve Pressure relief valve Diagnosis channelS337_01711 Engine managementThe turbocharger/exhaust manifold moduleTo save space, an exhaust manifold/turbocharger housing was developed, which can be installed with all engine variations in longitudinal or transverse configuration. Importance was also placed on realising a customer service orientated solution to allow the exhaust manifold to be removed and installed easily, and for a catalytic converter to be included close to the engine.Crankcase breather connection Coolant flow to radiator and from auxiliary water pumpActive charcoal filter connection Pressurised oil supplyTurbocharger air recirculation valve N249Coolant supply to engine block Oil returnS337_018The bearing of the turbine shaft is integrated in the compressor housing. The cylinder head cover houses the crankcase and active charcoal breather connections. Screwed into the pressure connection is an individually tuned resonance silencer to reduce the pressure pulsation noises. The required charge pressure is adjusted via the charge pressure control solenoid valve N75 (pressure relief control as on 1.8 l turbocharged engine) and the so-called wastegate. The charge pressure control solenoid valve N75 and the turbocharger air recirculation valve N249 can be found on the turbocharger.12 The turbocharger with new flange fixtureThe turbocharger module is easy to fit and is attached to the cylinder head by five threaded connections. For removal and installation, the clamping strip need not be loosened. The exhaust manifold is designed to take advantage of the firing order. The manifold is fluted to channel the exhaust gases equally over the turbine. In this way, the exhaust ports are separated in line with the firing order. Furthermore, the flute channel prevents the exhaust gas pressure from expanding into other cylinder ports. This means that the required turbine speed is maintained and the response of the turbocharger could be optimised.Flute channelClamping stripS337_01913 Engine managementCharge pressure flow and charge pressure controlControl pressure is formed from the charge pressure and intake pressure via the energised charge pressure control solenoid valve N75. The control pressure affects the vacuum unit, which actuates the wastegate valve via a linkage. The wastegate valve opens a bypass channel to allow part of the exhaust gases past the turbine into the exhaust gas system. This control feature allows the speed of the turbine to be controlled and the maximum charge pressure can thereby be regulated.If the control features fails, the vacuum unit is affected directly by the charge pressure, which imparts pressure against the spring. The maximum charge pressure is thereby restricted to a basic operating charge pressure.Turbocharger air recirculation valve N249 Wastegate Charge pressure control solenoid valve N75 Vacuum unitCharge air coolerS337_02014 The electric overrun air recirculation control (previously pneumatic)In order to prevent the turbocharger from braking too heavily in overrun and between gear changes, an electric turbocharger air recirculation valve N249 is installed. The electric overrun air recirculation control is much more durable than the pneumatic one. In overrun, the vacuum unit is completely closed. The overrun air recirculation control is open, even between gear changes. During overrun, pressure is built up in the compressor housing due to the prevailing charge pressure. This pressure build-up causes the compressor wheel to brake heavily, which leads to a reduction in the prevailing charge pressure (turbo drop). To prevent this from happening, the turbocharger air recirculation valve N249 is opened by an electric servomotor. It opens a bypass channel to pass compressed air via the compressor wheel back to the suction side of the compressor circuit. This keeps the turbine at a constant speed. When the throttle valve is opened, the turbocharger air recirculation valve N249 is closed and charge pressure is immediately available again.OverrunAir intake from air cleanerOverrun air recirculation valve openUnder loadOverrun air recirculation valve closedS337_02715 Engine managementThe cooling system with coolant run-on pump and radiator run-onTo prevent oil deposits from burning onto the turbine shaft in the turbocharger, an auxiliary water pump runs-on for up to 15 minutes after the engine has been switched off. It transports the cooler coolant against the direction of normal flow. As it does this, coolant drawn in from the auxiliary pump flows from the radiator via the turbocharger in the engine block and back to the radiator to break down the residual heat.Connection on turbochargerEngine block connectionAuxiliary water pump operationEngine operation Engine operation Auxiliary water pump operationRadiator outletAuxiliary water pump Radiator inletS337_02116 The tumble flapsSince the engine is operated in homogenous mode, the tumble flaps are used to improve the internal mixture formation.At low loads, in a speed range from 1000 rpm to 5000 rpm, the tumble flaps are closed: - to improve idling speed quality on a cold engine - to increase the tumble effect and thereby improve smooth running of the engine - in overrun to prevent engine joltsTorque [Nm]Output [kW]In other speed ranges, the tumble flaps are open to avoid any resistance to flow and thereby a reduction in performance.Range in which tumble flaps are closed.Speed [rpm]S337_022Tumble flap with steel shaftCoupling rodThrottle valve moduleIntake manifold flap motor V157 with intake manifold flap potentiometer G336S337_02317 Engine managementThe fuel supplyThe direct injection petrol engines are supplied with fuel via a demand-controlled fuel pump. This demand-control feature was developed to bring the energy requirement of the fuel pump to a low level and thereby to save fuel. To achieve increasingly high pressures, the pump is driven by 3 cams (2 cams on AXW). The electric fuel pump provides just the amount of fuel required by the engine at a prescribed system pressure. This is controlled by the engine control unit and an electronic system that regulates the speed of the fuel pump via pulse width modulation.Fuel pressure regulating valve N276High pressure fuel pumpPump cams (qty. 3)High pressure injectorLow pressure fuel circuitFuel pressure sender for low pressure G410High pressure fuel circuit Pressure limitation valve Fuel pressure sender G247S337_02418 Modes of operationThe turbocharged engine is driven in two modes of operation. Dual injection with cold start Dual injection is a special mode of operation for rapid heating of the catalytic converter. To do this, a quantity of fuel is injected on the intake stroke at approx 300° before TDC of ignition. The fuel distributes itself homogeneously due to the long gap before ignition. The second injection occurs at approx. 60° before TDC of ignition in the compression phase. The rich mixture that thereby forms around the spark plug means that timing can be retarded to a considerable degree without affecting stability of the engine. Both injection periods result in lambda 1. Since the exhaust valves are already open, the exhaust gas temperature rises rapidly. This brings the catalytic converter to operating temperature (350°C) in a short space of time (30-40 seconds). When the driver door is opened, the electric fuel pump is energised by means of the door contact switch. The prestart serves as a means of shortening the start time and to build-up pressure more rapidly. A maximum counter is installed to prevent the pump from becoming damaged.Main mode of operation with catalytic converter at operating temperature Only homogenous injection occurs in the area of the spark plugs, as no additional heating of the catalytic converter is necessary. The engine sets to lambda 1. To prevent heat bubbles forming in the fuel line, the electric fuel pump is actuated even when the engine is at operating temperature.19 Engine managementThe system overviewG70 Air mass meter G31 Charge pressure sender G42 Intake air temperature sender G28 Engine speed sender G40 Hall sender J338 Throttle valve module G187 Throttle valve drive angle sender 1 for EPC G188 Throttle valve drive angle sender 2 for EPC G79 Accelerator pedal position sender G185 Accelerator pedal position sender 2 F F47 Brake light switch Brake pedal switchJ220 Motronic control unit T16 Diagnosis interfaceG247 Fuel pressure sender G336 Intake manifold flap potentiometer G61 Knock sensor 1 G66 Knock sensor 2 G62 Coolant temperature sender G83 Coolant temperature sender at radiator outlet G410 Fuel pressure sender for low pressureCAN driveG42 Intake air temperature sender G39 Lambda probe G130 Lambda probe after catalytic converter G476 Clutch position sender Alternator DF CCS on/offJ519 Onboard supply ctrl unit J533 Diagnosis interface for data bus20COM lead J538 Control unit for fuel pumpG G6Fuel gauge sender Fuel system pressurisation pumpN30 - N33 Injectors for cylinders no. 1 - 4 N70 Ignition coil 1 with final output stage N127 Ignition coil 2 with final output stage N291 Ignition coil 3 with final output stage N292 Ignition coil 4 with final output stage J338 Throttle valve module G186 Throttle valve drive for electronic power control J317 Voltage supply relay term.30 J757 Voltage supply relay for engine components J329 Term. 15 voltage supply relay N80 Active charcoal relay solenoid valve 1 N276 Fuel pressure control valveV157 Intake manifold flap motorN205 Inlet camshaft control valve 1J285 Control unit in dash panel insertN75 Charge pressure control solenoid valve N249 Turbocharger air recirculation valve Z19 Lambda probe heating Z29 Lambda probe 1 heater after catalytic converterJ527 Control unit for steering column electronics J104 Control unit for ABSJ235 Coolant pump relay V50 Coolant circulation pumpJ293 Radiator fan control unit (PWM)S337_02621 Engine managementFunctional diagramA F F47 G G1 G6 G28 G31 G39 G40 G42 G61 G62 G66 G70 G79 G83 G130Battery Brake light switch Brake pedal switch Fuel gauge sender Fuel gauge Fuel pump Engine speed sender Charge pressure sender Lambda probe Hall sender Intake air temperature sender Knock sensor 1 Coolant temperature sender Knock sensor 2 Air mass meter Accelerator pedal position sender Coolant temperature sender at radiator outlet Lambda probe after catalytic converterG185 G186 G187 G188 G247Accelerator pedal position sender 2 Throttle valve drive for electronic power control Throttle valve drive angle sender 1 for electronic power control Throttle valve drive angle sender 2 for electronic power control Fuel pressure senderColour coding/keyOutput signal Earth Input signal Positive CAN drive train22 S337_025G336 G410 G476 J220 J235 J285 J317 J329 J338 J519 J533 J538 J682 J757 N30 N31 N32 N33 Intake manifold flap potentiometer Fuel pressure sender for low pressure Clutch position sender Motronic control unit Coolant pump relay Control unit in dash panel insert Term. 30 voltage supply relay Term. 15 voltage supply relay Throttle valve module Onboard supply control unit Data bus diagnosis interface Control unit for fuel pump Term. 50 voltage supply relay Voltage supply relay for engine components Injector for cylinder no. 1 Injector for cylinder no. 2 Injector for cylinder no. 3 Injector for cylinder no. 4 N70 N75 N80 N127 N205 N249 N276 N291 N292 P Q S T16 V50 V157 Z19 Z29 Ignition coil 1 with final output stage Charge pressure control solenoid valve Active charcoal filter system solenoid valve 1 Ignition coil 2 with final output stage Inlet camshaft control valve 1 Turbocharger air recirculation valve Fuel pressure control valve Ignition coil 3 with final output stage Ignition coil 4 with final output stage Spark plug connector Spark plugs Fuse Diagnosis interface Coolant circulation pump Intake manifold flap motor Lambda probe heating Lambda probe 1 heater after catalytic converter23 ServiceSpecial toolsDesignationT10252 Camshaft barToolApplicationTo lock camshaft in order to remove pulleyVAG 1687 Charge air system testerTo check for leaks in charge air systemWith new adapter 1687/524 Special toolsDesignationT10133 FSI special tool caseToolApplicationCommon special tools for repairs to FSI engines. Also used on turbocharged FSI engine.T40057 Oil drain adapterTo drain engine oil from oil filter housingT40001 PullerTo pull off camshaft pulleyT40001/1 - 7 Arms for puller25 Test your knowledge1. In which mode of operation is the T-FSI driven?… a) Homogeneous mode … b) Homogeneous lean mode … c) Stratified mode2. When are the tumble flaps actuated?3. Where is the elliptical CTC toothed belt pulley used?… a) Variable valve timing … b) Balancer shaft drive … c) Toothed belt drive4. The flute channel in the exhaust manifold has the following tasks… a) Equal flow of exhaust gases to turbocharger … b) Prevents back flow of exhaust gases … c) Turbocharger speed is maintained … d) Response of turbocharger is optimised26Answers: 1. a 2. At low load in a speed range of 1000 - 5000 rpm 3. c 4. a, b, c, d Notes27 337For internal use only © VOLKSWAGEN AG, Wolfsburg All rights reserved, including the right to make technical changes 000.2811.52.20 Technical status 12/04❀ This paper was made fromchlorine-free pulp.