TECHNICAL DOCUMENTATION

SSP 340 The Passat 2006 Electrical System

PDFEN60 pages4 MB
SSP 340 The Passat 2006 Electrical System - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingSelf-study Programme 340The Passat 2006 Electrical SystemDesign and Function The Passat 2006 features further innovations in the area of vehicle electrics and electronics. The developers have paid particular attention to comfort in this car.One example is the entry and start authorisation switch. For the first time, you do not have to turn the ignition key to start the engine. This self-study programme should help you get to know the electrical system in the Passat 2006 and become familiar with the new features.S340_072NEWImportant NoteThe self-study programme shows the design and function of new developments. The contents will not be updated.For current testing, adjustment and repair instructions, refer to the relevant service literature.2 ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Data Bus Systems Control Units for Powertrain CAN Data Bus . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Control Units for Convenience CAN Data Bus . . . . . . . . . . . . . . . . . . . . . . . 10 Control Units for Infotainment CAN Data Bus Combi and Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Sub-bus Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Onboard Power Supply Electronics Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Relay Carriers and Fuse Boxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Onboard Power Supply Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Exterior lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Data Bus Diagnostic Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Control Unit with Display in Dash Panel Insert . . . . . . . . . . . . . . . . . . . . . . . 34 Convenience System Central Control Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Immobilizer IV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Start-Stop System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Electronic Steering Column Lock Control Unit . . . . . . . . . . . . . . . . . . . . . . . 46 Convenience and Safety Electronics Corning Light System (Advanced Frontlighting System) . . . . . . . . . . . . . . . . 48 Customisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 Parking Aid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Transformer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56Test Yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 583 IntroductionFuse Boxes and Relay Locations in the Onboard Power SupplyLocationsThe Passat 2006 onboard power supply is decentralised and is therefore similar to the Golf 2004 system. The Passat also has a fuse box on the right-hand side of the dash panel due to the large number of electrical consumers. The distribution of the fuse boxes and relays among different locations allows fast and precise fault diagnosis.Fuse box, in right-hand side of dash panelElectronics box, on left of engine compartmentBack-up fuse box, on left of engine compartment4 Relay carrier, on left under dash panel, above onboard power supply control unitRelay carrier on onboard power supply control unit, on left under dash panelS340_001 Fuse box, on left in dash panel5 IntroductionNetworking ConceptOverview of networked control unitsThe data bus diagnostic interface J533 forms the interface for communication among the following data bus systems: Powertrain CAN data bus Convenience CAN data bus Infotainment CAN data bus Combi CAN data bus Diagnostics CAN data busJ428 T16 J788 J623 J583J745J667The following data bus systems are connected downstream of a CAN data bus system as a sub-bus system: - LIN data bus - CAN data bus, electromechanical parking brake - Sensor CAN data bus - Cornering lights CAN data bus - Serial data busJ533 J503 / R J345J668J285J521J412 J519Powertrain CAN data bus Convenience CAN data bus Infotainment CAN data bus Cornering lights CAN data bus Electromechanical parking brake CAN data bus LIN data bus Sensor CAN data bus Combi CAN data bus Diagnostics CAN data bus CAN data bus cable Communications line LIN data bus cable Serial data bus cable S340_003J525 J255 J364 J136J738J386J388J387J3896 G419J540J492J217 J743J104J587J500J234G85E221E415 J527J446J605J400 G397J604J393 H12 J764G384 G273S340_002E221 Operating unit in steering wheel E415 Entry and start authorisation switch G85 Steering angle sender G273 Interior monitoring sensor G384 Vehicle inclination sender G397 Rain and light detector sensor G419 ESP sensor unit H12 Alarm horn J104 ABS control unit J136 Seat and steering column adjustment control unit with memory J217 Automatic gearbox control unit J234 Airbag control unit J255 Climatronic control unit J285 Control unit with display in dash panel insert J345 Trailer detector control unit J364 Auxiliary heater control unit J386 Driver door control unit J387 Front passenger door control unit J388 Rear left door control unit J389 Rear right door control unit J393 Convenience system central control unit J400 Wiper motor control unit J412 Mobile telephone operating electronics control unit J428 Adaptive cruise control unit J446 Parking aid control unit J492 Four-wheel drive control unit J500 Power steering control unit J503 Control unit with display for radio and navigation J519 Onboard power supply control unit J521 Front passenger seat position with memory control unit J525 Digital sound package control unit J527 Steering column electronics control unit J533 Data bus diagnostic interface J540 Electromechanical parking brake control unit J583 NOx sensor control unit J587 Selector lever sensors control unit J604 Auxiliary air heater control unit J605 Boot lid control unit J623 Engine control unit J667 Power output module for left headlight J668 Power output module for right headlight J738 Telephone controls control unit J743 Mechatronics for direct shift gearbox J745 Cornering light and headlight range control unit J764 Electronic steering column lock control unit J788 Powertrain CAN bus isolation relay R Radio T16 Diagnosis connection 16-pin connector7 Data Bus SystemsControl Units for Powertrain CAN Data BusControl units and locationsThe adjacent diagram shows the control units that are involved in the powertrain CAN data bus communication as well as their locations. The data transfer speed is 500kbit/s. The transfer occurs via the CAN high cable and the CAN low cable. The CAN cables are twisted together for secure data transfer. The powertrain CAN data bus is not suitable for use with a single cable – data transfer would not be possible if one CAN cable fails.Headlight range control, control unit J431, on right-hand side of glove compartmentABS control unit J104, on the bulkhead, on right inside engine compartmentDue to new terminology for the names of components, some terms may be different to those used in other self-study programmes.Adaptive cruise control unit J428 *, behind the brand badge* To be used at a later point in time.Engine control unit J623, under the plenum chamber cover8 Selector lever sensors control unit J587, under centre console at front Airbag control unit, under centre console at frontFour-wheel drive control unit J492 *, on the Haldex coupling, in front of the rear axleSteering column electronics control unit J527, under the steering column switchData bus diagnostic interface J533, on left under dash panel Automatic gearbox control unit J217, in front left wheel housingPower steering control unit J500, on the steering rack near the bulkheadS340_0049 Data Bus SystemsControl Units for Convenience CAN Data BusControl units and locationsThe adjacent diagram shows the control units that are involved in the convenience CAN data bus communication as well as their locations. The data transfer speed is 100 kbit/s. The transfer occurs via the CAN high cable and the CAN low cable. The CAN cables are twisted together for secure data transfer. The convenience CAN data bus is suitable for use with a single cable – data transfer would still be possible if one CAN cable fails.Front passenger seat position with memory J521, under passenger seatDoor control units J386, J387, J388, J389, in the doorsConvenience system central control unit J393, on right under dash panelClimatronic control unit J255, in middle of dash panel10 Parking aid control unit J446, in the side section at rear right Trailer detector control unit J345, in the side section at rear leftMultifunction steering wheel control unit J453, in the steering wheelSteering column electronics control unit J527, in the steering columnSeat and steering column adjustment control unit with memory J136, under driver’s seat Onboard power supply control unit J519, on relay carrier under the dash panel S340_00511 Data Bus SystemsControl Units for Infotainment CAN Data Bus Combi and DiagnosisControl units and locationsThe adjacent diagram shows the control units that are involved in the infotainment and combi CAN data bus communication as well as their locations.Infotainment CAN data busThe data transfer speed is 100 kbit/s. The transfer occurs via the CAN high cable and the CAN low cable. The CAN cables are twisted together for secure data transfer. The infotainment CAN data bus is suitable for use with a single cable – data transfer would still be possible if one CAN cable fails.Combi and diagnosis CAN data busThe data transfer speed is 500 kbit/s. The transfer occurs via the CAN high cable and the CAN low cable. The CAN cables are twisted together for secure data transfer. The combi and diagnosis CAN data bus systems are not suitable for use with a single cable – data transfer would not be possible if one CAN cable fails.CD changer R41, in glove compartmentAuxiliary heater control unit J364, in right wheel housing12 Control unit with display for radio and navigation J503, in the dash panel Mobile telephone operating electronics control unit J412, under passenger seatControl unit with display in dash panel insert J285Digital sound package control unit J525, under driver’s seatDiagnosis connector T16 on left under dash panel, driver’s sideData bus diagnostic interface J533, in footwell on driver’s side, near pedalsS340_00713 Data Bus SystemsSub-bus SystemsLIN data busThe Local Interconnect Network is a local system that transfers data via a single-wire connection at a data transfer rate of 1 - 20 kbit/s. The transfer rate is stored in the master control unit software. The data exchange occurs between a master control unit and up to 16 slave control units. The communication between the individual subscribers is initiated exclusively by the master control unit that can also communicate on the CAN data bus.Control Units for LIN Data BusJ393 G397 J533 J400 J519G384 G273H12S340_062 Legend G273 Interior monitoring sensor G384 Vehicle inclination sender G397 Rain and light sensor H12 Alarm horn J393 Convenience system central control unit J400 Wiper motor control unit J519 Onboard power supply control unit J533 Data bus diagnostic interface14 Electromechanical CAN data busThe data transfer speed of the electromechanical parking brake CAN data bus is 500 kbit/s. The transfer occurs via the CAN high cable and the CAN low cable. The CAN cables are twisted together for secure data transfer. The powertrain CAN data bus is not suitable for use with a single cable – data transfer would not be possible if one CAN cable fails.Control units for electromechanical parking brake CAN data busJ104J533J540S340_063 Legend J104 ABS control unit J533 Data bus diagnostic interface J540 Control unit for electromechanical parking brakeAdditional CAN data bus systems are necessary due to the high requirements (data rate and quantity).15 Data Bus SystemsCornering Lights (Advanced Frontlighting System) CAN Data BusThe data transfer speed of the cornering light CAN data bus is 500 kbit/s. The transfer occurs via the CAN high cable and the CAN low cable. The CAN cables are twisted together for secure data transfer. The cornering light CAN data bus is not suitable for use with a single cable – data transfer would not be possible if one CAN cable fails.Control units for cornering light CAN data busJ668J745J533J667S340_064 Legend J533 Data bus diagnostic interface J667 Power output module for left headlight J668 Power output module for right headlight J745 Cornering light and headlight range control unit16 Sensor CAN data busThe data transfer for the sensor CAN data bus is the same as the cornering light CAN data bus and transfers the data between the engine control unit and the NOx sensor control unit.J583J623J533S340_065 Legend J533 Data bus diagnostic interface J583 NOx sensor control unit J623 Engine control unitSerial data busThe serial data bus transfers the data via a single-wire connection at 9800 kbit/s between the electronic steering column lock control unit and the convenience system central control unit. Using the serial data bus system increases theft protection compared with use of the LIN data bus system.J393J533 J764S340_066 Legend J533 Data bus diagnostic interface J393 Convenience system central control unit J764 Electronic steering column lock control unit17 Onboard Power SupplyElectronics BoxLocationThe electronics box is mounted at the front right in the engine compartment.DescriptionAll fuses and relays for protection and control of the electrical components in the engine compartment are accommodated in the electronics box. There is therefore no cable running into the interior and back. Troubleshooting is made easier, the protection is configured better to the consumer and multiple assignment of fuses is avoided to a great extent.S340_010Please refer to the ELSA electronic service information system for the current assignment with fuses and relays in the electronics box.18 Electronics BoxThe electronics box also contains the following relay in addition to the fuses for the components in the engine compartment: - Voltage supply relay terminal 30 J317S340_011Back-up fuse boxThe back-up fuse box contains the fuses for the alternator, the electromechanical power steering, the radiator fan, the ABS control unit.S340_01219 Onboard Power SupplyRelay Carriers and Fuse BoxesLocationsThe relay carrier and the onboard power supply control unit are under the left-hand side of the dash panel.Relay carrierThe relays connected to the relay carrier depend on the vehicle version and the equipment. On vehicles with heated seats, the circuit breakers for the heating elements (thermal fuses) are also mounted on the relay carrier.S340_008Relay carrier on onboard power supply control unitThere is an additional relay carrier on the onboard power supply control unit.S340_00920 Left-hand fuse boxThe fuse box is on the left-hand side of the dash panel behind the cover.S340_013Right-hand fuse boxThe fuse box is on the right-hand side of the dash panel behind the cover.S340_014Please refer to the ELSA electronic service information system for the current assignment of the fuses.21 Onboard Power SupplyOnboard Power Supply Control Unit J519LocationThe onboard power supply control unit is on the left underneath the dash panel and forms a unit with the relay carrier.S340_009VersionsThe Passat is equipped with two different versions of the onboard power supply control unit.●High version for vehicles with fog lights and/or Bi-Xenon lights and customisation options.●Medium version for all other vehicle variants.Fog lights can be retrofitted only if the medium version of the onboard power supply control unit is also exchanged for the high versions.22 TasksThe onboard power supply control unit switches and controls the following functions:●Outside light control with bulb monitoring The blown bulb is indicated by the corresponding warning light or as a text in the dash panel insert. Convenience lights with Coming Home After the vehicle doors are closed, the area surrounding the vehicle is illuminated by a lighting system on the vehicle. Leaving Home The area surrounding the vehicle will be illuminated by a lighting system when the car is unlocked with the remote control. Dimmable instrument lighting●Front windscreen wiper The CAN data bus signals are forwarded from the onboard power supply control unit to the wiper motor control unit Rear windscreen wipers When you select reverse gear, the rear windscreen wiper is switched on (estate only). Windscreen and rear window washer pump Turn signal control Electrical load management Switch-off under 11.8 V, as in Touran. Outside light control Heated rear windscreen Heated front windscreen Terminal control The onboard power supply control unit controls terminal 75x via the X-contact relief relay. Terminal 15 is controlled via the relay for voltage supply terminal 15 in the electronics box. Terminal 50 is controlled via the relay for voltage supply terminal 50 in the electronics box.●●●●●●●Gear selector lighting● ●Interior light control Terminal 30G, via which the interior lights are supplied with power, is switched by the onboard power supply control unit. Fuel pump supply When you open the driver’s door, the electrical fuel pump is supplied by the onboard power supply control unit with voltage. After you start the engine, the voltage is supplied by the engine control unit.●●23 Onboard Power SupplyExterior LightsFront headlightsDesignThe shape of the headlights is no longer the classic double round design. “Large eyes” are formed by tubes around the dipped beam lights. The large square full-beam reflector improves the full-beam performance considerably compared with the Passat 1997.H7 headlightsThe basic headlights use halogen technology. H7 lights are used for both the dipped and full-beam lights. A voltage stabilising system used by the onboard power supply control unit increases the life of the bulbs.S340_015Xenon headlightsThe Passat 2006 can be ordered with optional Bi-Xenon headlights with cornering light function.S340_016Xenon headlights are run with high-voltages of several 10,000 volts. Contact with this voltage can be fatal. Therefore make sure you follow the safety guidelines given in the ELSA electronic service information system.24 Tail lightsDesignThe tail lights feature the double round light design. They are two-piece.Tail lights in side sectionThe tail light, brake lights and indicators use LEDs and are integrated in the side section. The advantages of LEDs over bulbs are faster response times, better signal formation and greater homogeneity of the illuminated areas.Tail lights in the boot lidThe rear fog light is on the left of the boot lid and the reverse light is on the right. Normal bulbs are used here.S340_017 Tail light and turn signal Tail light and brake signal Rear fog lightThird brake lightA third brake light as well as the indicators mounted in the door mirrors compliment the headlights and tail lights and provide other road users with additional visual signals. The third brake light at the top of the rear windscreen as well as the indicators in the door mirrors use LED technology.Third brake lightS340_018The whole unit will need to be replaced if individual LEDs are faulty.25 Onboard Power SupplyRotary light switchIn the midline and highline version of the onboard power supply control unit, the light switch is a semiconductor element. It is therefore only used for activation. The lights are controlled by the onboard power supply control unit output stage.Rotary light switch without automatic headlight controlThe light in the light switch is illuminated when terminal 75 is switched active.S340_019Rotary light switch with automatic headlight controlThe symbol for automatic headlights is illuminated red when the light switch is set to “automatic headlight control”. When the switch is in the “automatic headlight control” position and the rain and light detector sensor has detected night-time or darkness, the symbol will be illuminated green. When the switch is in the “automatic headlight control” position and the rain and light detector sensor has detected day-time or light, the symbol will be illuminated light green.S340_020You will find further information on use of the rotary light switch and the warning lights in the Passat 2006 operating manual.26 Indicator functionsThe following indicator modes are available in the Passat 2006: Hazard warning lights Crash warning lights Emergency stop warning lights Turn signals Lane change flash - Central locking flashing - Anti-theft alarm flashingThe individual operating modes have different priorities. This allows a flash function to be activated even though another one is in use. Priority 1 Priority 2 Priority 3 Hazard warning lights Crash warning lights Emergency stop warning lights Priority 4 Priority 5 Turn signals, lane change flash Anti-theft alarm flash, central locking flashHazard warning lightsThe “hazard warning lights on” function is sent directly from the hazard warning light switch to the onboard power supply control unit. This information is not related to the status of terminal 15.Turn signalsThis function is realised in the onboard power supply control unit and by the steering column electronics control unit. It is activated with the turn signal switch.Lane change flash Crash warning lightsThe hazard warning lights are switched on automatically when the airbag control unit recognises a crash. If the turn signal switch is pressed for less than 1 second, the indicators will flash three times. Pressing the turn signal switch in the same direction for less than one second will add three more flashes. The function can be activated with the customisation options or the VAS tester.Emergency stop warning lightsThe hazard warning lights are switched on in an emergency braking situation (deceleration 7 m/s2 longer than 700 ms) or when the ABS is active for more than two seconds. This function needs to be activated in the onboard power supply control unit using a VAS tester.Anti-theft alarm and central lock flashThese flash functions are requested by the convenience system central control unit from the onboard power supply control unit via the CAN data bus when the corresponding function is active.27 Onboard Power SupplyExterior lights functional diagramS340_021Legend D1 Immobilizer reading unit E1 Light switch E2 Turn signal switch E3 Hazard warning light switch E4 Headlight dipper/flasher switch E7 Fog light switch E18 Rear fog light switch E20 Switches and instruments illumination regulator E22 Intermittent wiper switch E34 Rear wiper switch E38 Intermittent wiper regulator E44 Washer pump switch (automatic wash/wipe and headlight washer system) E102 Headlight range control regulator E415 Entry and start authorisation switch F Brake light switch F4 Reversing light switch F266 Bonnet contact switch J285 Control unit with display in dash panel insert J362 Immobilizer control unit J386 Driver door control unit J387 Front passenger door control unit J393 Convenience system central control unit J519 Onboard supply control unit J527 Steering column electronics control unit J533 Data bus diagnostic interface J764 Electronic steering column lock control unitK1 K4 K6 K13 K18 K65 K94 K170 L9 L22 L23 L46 L76 L131Main beam warning lamp Side light warning lamp Hazard warning light system warning lamp Rear fog light warning lamp Trailer operation warning lamp Left turn signal warning lamp Right turn signal warning lamp Bulb failure warning lamp Light switch illumination bulb Left fog light bulb Right fog light bulb Rear fog light bulb Button illumination bulb Exterior mirror turn signal bulb, driver’s side L132 Exterior mirror turn signal bulb, front passenger side M1 Left side light bulb M2 Right tail light bulb M3 Right side light bulb M4 Left tail light bulb M5 Front left turn signal bulb M6 Rear left turn signal bulb M7 Front right turn signal bulb M8 Rear right turn signal bulb M9 Left brake light bulb M10 Right brake light bulb28 S340_069M17 Right reversing light bulb M25 High level brake light bulb M29 Left dipped beam bulb M30 Left main beam bulb M31 Right dipped beam bulb M32 Right main beam bulb N360Steering column lock control element N376 Ignition key withdrawal lock solenoid S Fuse V48 Left headlight range control motor V49 Right headlight range control motor W31 Front left entry light W32 Front right entry light X Number plate lightInput signal Output signal Positive Earth Data bus29 Onboard Power SupplyAutomatic headlight controlDusk functionIf light switch E1 is set to “automatic headlight control”, the rain and light detector sensor G397 automatically measures the light, e.g. when entering a tunnel, and sends a signal to the onboard power supply control unit to automatically switch on the driving lights.Legend E1 Light switch E415 Entry and start authorisation switch G397 Rain and light sensor J519 Onboard supply control unit L123 Left dipped beam bulb L124 Right dipped beam bulb L125 Left main beam bulb L126 Right main beam bulb E415 G397E1 J519L124L126L123L125 S340_067Motorway functionThe motorway function switches the driving lights on when the car travels faster than 140 km/h for over 10 seconds. They are switched off again when the car travels slower than 65 km/h for longer than 150 seconds. The function is activated when the light switch is set to “automatic headlight control”.S340_022Rain functionThe rain function switches the driving lights on when the front wipers are active for longer than 5 seconds and the light switch is set to “automatic headlight control”. The driving lights are switched off again when there is no wipe procedure for longer than 255 seconds.S340_02330 Vehicle lightsEmergency light modeIf the onboard power supply control unit is not capable of controlling the car lights due to a processor malfunction, an additional piece of hardware will take over the following lights: - Brake light - Side light - Dipped beamLight functionsThe following lights have additional functions:Lights Rear left and right brake lights Additional functions Dimmed switch on as tail light dimmed to 10% Dimmed switch on as tail light dimmed to 15%Rear left and right indicatorLight switch delayThe delay prevents the headlights being switched on briefly in the “automatic headlight control” position when you quickly turn the switch from the “off” position to the “side lights” or “headlights” position.From/toOff “Light Sensor” signalAutomatic headlight control “Light Sensor” signalSide light “Light Sensor” signalDriving lights “Light Sensor” signal “Lights off” (ms) 0 0 0“Lights on” “Lights off” “Lights on” “Lights off” “Lights on” (ms) (ms) (ms) (ms) (ms) Off Automatic headlight control Side light Driving lights 0 0 0 0 0 0 500 0 0 0 600 500 0 0 600“Lights off” “Lights on” (ms) (ms) 0 0 0 0 0 60031 Onboard Power SupplyData Bus Diagnostic Interface J533FunctionDue to the high proportion of networked functions, large quantities of data have to be transferred. To ensure trouble-free data exchange, several data bus systems are required to exchange data between each other. The data bus diagnostic interface links these data buses as a gateway interface and allows data transfer.LocationThe data bus diagnostic interface is on the left under the dash panel, above the accelerator pedals.Master functionsThe data bus diagnostic interface J533 takes over the master functions for terminal 15 run-on on the powertrain CAN data bus as well as the control logic for sleep and wake-up mode of the data bus systems.S340_028For more information on the data bus diagnostic interface, see SSP 307 “The Touran – Electrical System”.32 Transport modeThe car battery can be discharged during long transportation and standing times due to no-load currents. Transport mode is activated to keep power consumption as low as possible. Control unit with display in dash panel insert J285 indicates that transport mode is active. While transport mode is active, the car can be started and can be driven normally. The following convenience and infotainment consumers are deactivated:● ● ● ● ● ●Central locking Window regulators Radio Multifunction steering wheel Remote control Interior monitoring● ● ● ● ● ●Receiver for auxiliary heater remote start Inclination sensor Save LED in the door Interior lights after 30 seconds active Seat memory Air conditioningDeactivate transport modeTransport mode can only be switched off with the VAS diagnostic testers via the vehicle self-diagnosis (collection services). It is automatically disabled after a distance 50 km.Activate transport modeTransport mode can only be switched on with the VAS diagnostic testers via the vehicle self-diagnosis (collection services). It can only be activated within the first 150 km.S340_02933 Onboard Power SupplyControl Unit with Display in Dash Panel Insert J285FunctionThe control unit with display in dash panel insert receives its information for the display unit and warning lights from the various control units via the data bus diagnostic interface J533 and via the combi CAN data bus. External sensor signals still reach the control unit in the dash panel insert from the following sensors via discrete wiring: F1 F9 F34 G17 G32 Oil pressure switch Handbrake warning switch Brake fluid level warning contact Ambient temperature sensor Coolant shortage indicator sender G33 G34 G266 J538 Windscreen washer fluid level sender Brake pad wear sender Oil level and oil temperature sender Fuel pump control unitG17F34G32E24G33G266F9G34J538F1S340_03034 VariantsThe gauges in the display in the dash panel insert Y24 are divided into three versions.Lowline versionThe lowline version has eight LED warning lights (E) and a semi-dot liquid crystal display (LCD) (F).ACDBEF S340_031 EMidline versionThe midline version has eight LED warning lamps (E), a mini-dot display (F), a semi-dot LCD in the speedometer (O) and in the rev counter (N).FNOS340_032Highline versionThe midline version has a dot-matrix display (K), a semi-dot LCD in the speedometer (O) and in the rev counter (N).KNOS340_033Common equipmentAll versions have: Rev counter (A) G5 Speedometer (B) G21 Coolant temperature gauge (C) G3 Fuel gauge (D) G135 Onboard Power SupplyEquipped with warning lampsSymbol Warning lamp Airbag Lowline X Midline X Highline X Warning text or warning Airbag fault Airbag Belt tensioner deactivated ABSABS (anti-lock brake system) Brake pad wearXXXXXPictogramCheck brake padBrake fluid lowXXXStop brake fluid Owner’s manual Engine fault Workshop! Emissions Workshop!Preheat (diesel engines) or Electronic Power Control Dynamic oil pressure warning Diesel particle filter Power steering Electronic Power Steering Electronic brake pressure distribution Parking brake / electromechanical parking brake Electromechanical parking brake Warning lamp ESP TCS Left-hand indicatorXXXX FlashingX FlashingX Flashing Pictogram Pictogram XEngine fault Workshop! Emissions Workshop! Stop Oil pressure Engine off Owner’s manual 3 x warning buzzerX XX XSteering lock fault! Lock steering! Move steering! Steering lock! Workshop! 3 x warning buzzerXXXXXXHandbrake on Release parking brake by hand! Depress brake pedal!XXXParking brake fault! Owner’s manual!XXXXXXAcoustic signalRight-hand indicatorXXXAcoustic signalTrailer turn signals Main beam Cruise controlX X XX X XX X X36 IconWarning lamp Bulb failureLowlineMidline XHighline XWarning text or warning e.g. Front left dipped beam defective! Constantly illuminated: Faulty bulb Flashing: HRC or AFS faulty e.g. Boot lid open! 1 x warning buzzer at speed of 6 km/h Driver’s door open! Passenger door open! Rear left door open! Rear right door open! 1 x warning buzzer at speed of 6 km/h Please refuel 1 x warning buzzer Stop! Check coolant Owner’s manual 3 x warning buzzerBoot lidXXPictogramDoor openXXPictogramFuel reserveXXPictogramCoolant low or overheating AlternatorXXPictogramXXXEngine check EOBD Bonnet openXXXEngine fault Workshop! Emissions Workshop! Door warning! Hood! 1 x warning buzzer when v 6 km/hXXPictogramRear fog lightsXXXOil levelXXPictogramCheck oil level Oil sensor Workshop! 1 x warning buzzerTyre pressure monitoring Shift lockXXXXXXSeat beltXXXPlease fasten seatbelt GongDay driving lightsXXXFuel cap openXXXWash fluid lowXXXTop up wash fluid 1 x warning buzzer37 Onboard Power SupplyConvenience System Central Control Unit J393LocationThe convenience system central control unit is located under the dash panel, on the right behind the glove compartment.TasksThe convenience system central control unit activates and controls the following functions: Central locking control unit Activation of rear door control units Activation of the fuel tank flap release Activation of the boot lid release Activation of the anti-theft alarm via LIN bus - Activation of the tyre pressure monitor - Activation of the immobilizer - Activation of the entry and start authorisation system. -S340_034In the Passat 2006, the tyre pressure monitoring (via tyre pressure sensors and tyre pressure monitor aerials), immobilizer control unit J362 and entry and start authorisation control unit J518 functions are combined in the convenience system central control unit for the first time. Furthermore the convenience system central control unit is the master control unit in the LIN anti-theft alarm data bus. The anti-theft alarm system includes the interior monitoring sensor G273, the intelligent anti-theft alarm system horn H12 and the vehicle inclination sensor G384.38 Central lockingThe convenience system central control unit controls all central locking functions. The central locking system includes the doors, the boot lid and the tank filler flap.There are three locking states.Unlocked Locked The doors can be opened from the inside and outside. The doors can only be opened from the inside by pulling the door handle once. The doors cannot be opened either from the inside or the outside.SafeLocking pointsIt is operated by the emergency lock cylinder in the driver’s door, the interior locking button and the remote control on the car key. The motors for the central locking in the driver’s and passenger door are controlled by the respective door control units. The control of the rear doors, the boot lid and the tank filler flap is handled by the convenience system central control unit.Operating central lockingIf the vehicle is locked via the interior locking button, the LED integrated in the button will illuminate. The doors can be opened from the inside by pulling the door handle once. When individual door opening is activated, opening the car mechanically with the car key only unlocks the driver’s door. Turning the key twice also only operates the door control unit on the driver’s side. Pressing the OPEN or CLOSE button more than 200 times outside the reception range of the convenience system central control unit blocks the remote control unit. The remote control needs to be re-activated by pressing the OPEN button and then unlocking the car with the car key (within one minute).39 Onboard Power SupplyImmobilizer IVWhat does the immobilizer IV comprise?The immobilizer IV is not a separate control unit, but a function. It includes:●Central FAZIT databaseThe central FAZIT database at Volkswagen in Wolfsburg is a essential component of the immobilizer IV. FAZIT stands for “Fahrzeugauskunft- und zentrales Identifikations-Tool” (Vehicle Information and Central Identification Tool). All theft-related data from the control units that are integrated in the “Immobilizer” function are stored in this database. It is not possible to adapt the control units used without an online connection to FAZIT.●●Storage of all theft-related features of the control units in the FAZIT central database in Wolfsburg. Communication of the convenience system central control unit, in which the immobilizer is integrated, with the other components involved. Encryption of the data communication between the individual control units.S340_03640 Data Transfer●●Only an online query by the diagnostic tester transfers the data safely, quickly and reliably in the car. A PIN query of the immobilizer components by fax or prior enabling of the components is not possible.●●All components involved in the immobilizer have to be taught online. All car keys (including replacements) are already pre-coded at the factory for a specific car and can only be taught for this vehicle.Data TransferFAZITVAS 5051J533J393S340_037 Legend J393Convenience system central control unit J533Data bus diagnostic interface41 Onboard Power SupplyImmobilizer componentsConvenience system central control unit J393The immobilizer function is integrated in the convenience system central control unit. The control unit needs to be adjusted online after a replacement.Entry and start authorisation switch (E415)The entry and start authorisation switch contains the reader coil for reading the transponder in the car key. The switch for entry and start authorisation does not need to be adjusted after changing.Electronic steering column lock control unit J764The approval for locking and unlocking the steering column is provided via the “Immobilizer” function in the convenience system central control unit. The control unit can only be replaced and adjusted together with the convenience system central control unit.Engine control unit J623The engine control unit is part of the “Immobilizer” function. Authorisation via the CAN data bus from the convenience system central control unit is required for continuous running of the engine. This control unit needs to be adjusted online after a replacement.E415 J527J623J393J764 S340_038 Legend E415 Entry and start authorisation switch J393 Convenience system central control unit J527 Steering column electronics control unit J623 Engine control unit J764 Electronic steering column lock control unit Reader coil line Powertrain CAN data bus S contact Coded voltage supply signal42 Replacement of control unitsControl units that are involved in the “Immobilizer” function can only be replaced with an online connection to the FAZIT database.Convenience system central control unit J393● ● ● ● ●Engine control unit J623Request data via online connection Data transfer via VAS tester Download data into control unit Teach control unit Teach car key● ● ● ●●Request data via online connection Data transfer via VAS tester Download data into control unit Data exchange between control unit and FAZIT Teach car keyElectronic steering column lock control unit J764 and convenience system central control unit J393● ● ●Request data via online connection Data transfer via VAS tester Download data into control unit●●Data exchange between control units and FAZIT Teach car keyJ764FAZITVAS 5051J393J533J623 S340_040Legend J393 Convenience system central control unit J527 Steering column electronics control unit J533 Data bus diagnostic interfaceJ623 Engine control unit J764 Electronic steering column lock control unit43 Onboard Power SupplyStart-Stop SystemEntry and start authorisation switchThe entry and start authorisation switch is part of the driving authorisation system. It is used as a mechanical holder for the ignition key, converts the push movement of the ignition key into electrical signals and picks up the reader coil for electronic identification of the ignition key.S340_044Key ignitionThe ignition key does not have a key bit as the car is started with a pushing movement for the first time, not by turning.Releasing the emergency key S340_042Emergency keyThe emergency key is used to open the driver’s door mechanically if you cannot open it with the remote control. It is inserted in the ignition key. Also the key ring holder is attached to it. It can be used when the emergency key is in the second notch.Emergency keyS340_04344 Key positionsThe various terminal voltages (terminal S, terminal 15) are activated and the start procedure is initiated by pushing the ignition key into the entry and start authorisation switch.S340_041Switch positionsThe following switch positions can be set by pushing the ignition key: P0 P1 P2 P3 Off S contact on Terminal 15 on Terminal 15 drive (the ignition key automatically moves to this position after starting) Terminal 50 onS340_045P0 P1 P2P3 P4- P4Functional DiagramLegend D1 Immobilizer reading unit D2 Immobilizer reader coil E415 Entry and start authorisation switch J362 Immobilizer control unit J519 Onboard supply control unit J527 Steering column electronics control unit J533 Data bus diagnostic interface J764 Electronic steering column lock control unit N376 Ignition lock withdrawal solenoid lock S340_04645 Onboard Power SupplyElectronic Steering Column Lock Control UnitControl unitThe electronic steering column lock is supplied with power by the convenience central control unit J393. Locking and unlocking as well as diagnosis is controlled with the convenience system central control unit via a serial data bus connection. To take the increased safety requirements into account, the electronic steering column lock release needs to be authorised by three separate control units.S340_047Lock/unlockThe following conditions need to be met:●An authorised key needs to be recognised by the immobilizer. Data bus diagnostic interface J533 (speed = 0 km/h; revs = 0 rpm) Steering column electronics control unit J527 (terminal 15 off; speed = 0 km/h)●Convenience system central control unit J393 (terminal 15 off; CAN signals from J533 and J527 OK) Entry and start authorisation switch E415 (S contact off, terminal 15 off) Electronic steering column lock control unit J764 (checks whether both speed signals from J533 and J527 are OK)●●●●The electronic steering column only unlocks when an authorised key is recognised by the immobilizer. Terminals 15 and 50 are only activated once the electronic steering column lock has been released.46 Functional DiagramJ527J386 J519J285 J533 E415J393J764 J623 J104S340_048 Legend E415 Entry and start authorisation switch J104 ABS control unit J285 Control unit with display in dash panel insert J386 Driver door control unit J393 Convenience system central control unit J519 Onboard supply control unit J527 Steering column electronics control unit J533 Data bus diagnostic interface J623 Engine control unit J764 Electronic steering column lock control unitCAN data bus Output signal Input signal Plus Serial data bus47 Convenience and safety electronicsCornering Light System (Advanced Frontlighting System)A cornering light system is optionally available for the Passat 2006.Dynamic cornering lightsThe dynamic cornering lights are adjusted to the steering angle during cornering and therefore guarantee optimum road illumination in all driving situations.S340_024Static cornering lightsThe static cornering light is particularly useful when you turn off at crossroads and into side roads. An additional bulb in the headlights is switched on for this.S340_025You will find further information on the cornering lights in SSP 335 “Cornering Light System”48 Dynamic cornering light operationThe dipped beam bulb module is swivelled horizontally by an integrated electric motor.Swivelling angleThe swivelling angle is approx. 15 degrees for the outside headlight and approx. 7.5 degrees for the inside headlight in the curve.15 ° 7.5 °7.5 ° 15 °S340_026IlluminationCurves are illuminated better due to the varying swivelling angles. The maximum possible illumination is reached by the headlight on the inside of the curve swivelling in twice as far as the headlight on the outside of the curve.S340_027At driving speeds under 10km/h, the bulb modules are not swivelled. Over 10km/h, the swivelling angle is basically dependent on the curve radius. The legal requirements stipulating that the headlights may be not swivelled while the vehicle is stationary are therefore fulfilled. Also, the headlights are swivelled slightly when the vehicle accelerates from a standstill and the steering angle remains constant.49 Convenience and safety electronicsCustomisationCustomisation options allow customers to make their own settings for convenience and infotainment functions. The specific settings for the different equipment functions are made using a control element and a display. The system is operated using the lever on the steering wheel and the menus are selected using the display in the dash panel insert Y24. The settings you select are stored in the control unit that is responsible for control of the respective function. The necessary information is transferred between the control unit in the dash panel insert and the respective control units via the CAN data bus.Control units involved in customisationY24J412 J285 J453 J364J533 J527J503R G397 J400 Legend G397 Rain and light sensor R Radio J285 Control unit with display in dash panel insert J364 Auxiliary heater control unit J386..J389 Door control units J393 Convenience system central control unit J400 Wiper motor control unit J412 Mobile telephone operating electronics control unitJ519J393J386 . J389 S340_053J453 Multifunction steering wheel control unit J503 Control unit with display for radio and navigation J519 Onboard supply control unit J527 Steering column electronics control unit J533 Data bus diagnostic interface Y24 Display in dash panel insert50 For example: Menu guide Lights & Vision Coming Home Leaving Home Footwell light Lane change flash Wipers Factory setting BackLane change flash OffLane change flash onOn Off BackOn Off BackLane change flash onLane change flash offOn Off BackOn Off BackLane change flash offShort press of button Long press of buttonOn Off BackS340_05451 Convenience and Safety ElectronicsParking AidThe parking aid supports the driver when manoeuvring and parking. It is based on the familiar 8-channel ultrasound technology.Parking aid control unit J446The parking aid control unit J446 is located in the boot at the rear right.S340_055Parking aid button E266The parking aid button is on the right next to the selector lever or gearstick. The parking aid is activated when you press the button or select reverse gear. It is switched off when you press the button again or automatically at a speed 15 km/h. The LED in the button turns yellow when the parking aid is active. If the LED is flashing, a fault has been detected.S340_056 Parking aid button52 Parking aid senderThe senders are mounted in the rear and front bumpers as well as the radiator grille.Signal flow diagramJ285Front3 G252 J217 2 J345 4 G206RearE266G253 J533 1 5 67G205G254 9J104J519G2048 J446G255 11 10 H22 H15Terminal 30 Terminal 15G203S340_057Legend E266 Parking aid button G203Rear left parking aid sender G204Rear centre left parking aid sender G205Rear centre right parking aid sender G206Rear right parking aid sender G252 Front right parking aid sender G253 Front centre right parking aid sender G254 Front centre left parking aid sender G255 Front left parking aid sender H15 Rear parking aid warning buzzer H22 Front parking aid warning buzzer J104 ABS/ESP control unit J217 Automatic gearbox control unit J285 Control unit with display in dash panel insert J345 Trailer detector control unit J446 Parking aid control unit J519 Onboard supply control unit J533 Data bus diagnostic interfaceSignal flow 1 Wheel speed from J104 to J446 via J533. 2 Selector lever position J217 to J446 via J533. 3 Vehicle speed from J285 to J446 via J533. 4 Trailer detection from J345 to J446 If a trailer is detected, only the front senders will be active. 5 Terminal 15 on and reversing light on from J519 to J446 6 Fault detected from J446 to J533 7 E266 pressed 8 Signals from the rear parking aid senders 9 Signals from the front parking aid senders 10 Trigger H15 11 Trigger H2253 Convenience and Safety ElectronicsTransformerThe Passat 2006 can be ordered with an optional 230 V/50 Hz electrical socket. A transformer has been installed in the car to produce the alternating voltage. It is permanently connected to the socket. This unit is located in the centre console in place of the cupholder.S340_006TransformerElectrical socketElectrical socketThe 230 V socket does not have an earth connector and can only be operated with a maximum continuous output of 150 W. Approx. 300 W can be supplied as a short peak output (2 min). The socket has a built-in child protection device, which also functions as a switch. A green LED above the socket shows that is working properly. If this LED flashes red, there is a fault. This can occur when the output exceeds 150 W for a long period (overtemperature cut-off) or the load draw is too high (greater than 300 W).S340_058No repairs may be carried out on 230 Volt systems. Therefore the whole module needs to be replaced when the socket or transformer is faulty.54 The socket is only powered when the engine is running (terminal 61). Except for the signal cable from the onboard power supply control unit, the transformer is connected to the onboard power supply control unit with a voltage supply (terminal 30) and an earth point. The alternating voltage stage is electrically isolated.Child protection micro switchTransformerStatus LEDS340_061The following appliances can be run with the transformer, for example:● ● ● ● ● ● ● ● ●Notebook power supply 75-110 W Games console 40-100 W Bulb 25-100 W Television ~85 W Baby bottle warmer ~80 W Battery charger ~50 W Mobile phone charger ~30 W DVD player ~30 W Shaver ~10 WS340_059The following appliances cannot be run with the transformer, for example:● ● ● ● ●Hairdryer 1000 W Vacuum cleaner 800 W Coffee machine 500 W Appliances with an earth connection Work lights with neon tubesS340_06055 ServiceWiper Adapter SystemsTwo new adapter systems are used for the wipers on the Passat 2006 called the side-lock and top-lock systems. Both systems allow you to replace the wiper blades in the parked position and ensure a more stable connection to the wiper arm.Side-lock adapter systemS340_074Top-lock adapter systemS340_07556 Washer Fluid HoseThe Passat 2006 features an improved connector system for the washer fluid hose.Washer fluid hose connectorReleaseLockS340_076Please refer to the ELSA electronic service information system for specific instructions on replacing wiper blades and separating the connectors.57 Test Yourself1. What is the maximum appliance output that can be connected constantly to the 230 V socket? a) 100 W b) 150 W c) 300 W d) 150 W, but only for 2 minutes2.Which functions are not integrated in the new convenience system central control unit? a) Immobilizer b) Tyre pressure monitoring c) Central locking d) Transformer3.Which light systems are used in the new Passat tail lights? a) LEDs only b) Bulbs only c) Bulbs in the side section, LEDs in the boot lid d) LEDs in the side section, bulbs in the boot lid58 4.Which components have to be adjusted using the FAZIT database? a) Convenience system control unit b) Electronic steering column lock control unit c) Engine control unit d) Onboard supply control unit5.Where is the entry and start authorisation switch? a) In the door handle b) In the dash panel c) In the boot d) In the driver’s door, next to the window switches6.How many sensors does the Passat 2006 parking aid system have? a) 4 sensors, just at the rear b) 6 sensors at the front, 6 sensors at the rear c) 4 sensors at the front, 4 sensors at the rear d) 6 sensors, just at the rearAnswers: 1 b; 2 d; 3 d; 4 a, b, c; 5 b; 6 c59 340© VOLKSWAGEN AG, Wolfsburg All rights and rights to make technical alterations reserved. 000.2811.55.20 Technical status 02/2005 Volkswagen AG Service Training VK-21 Brieffach 1995 38436 Wolfsburg❀ This paper was manufactured from pulp that was bleached without the use of chlorine.