TECHNICAL DOCUMENTATION

SSP 341 The 4,2l V8 5V engine

PDFEN40 pages3 MB
SSP 341 The 4,2l V8 5V engine - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingSelf-study programme 341The 4.2l V8 5V engineDesign and function The 4.2l V8 5V engine will be launched in two variants: - In the Touareg, with an output of 228kW - In the Phaeton, with an output of 246kWBesides their differences in output, the two engines will differ primarily as a result of the modifications necessary for the Touareg's off-road capability.S341_001NEWAttention NoteThe self-study programme portrays the design and function of new developments! The contents will not be updated.For current testing, adjustment and repair instructions, please refer to the customer service literature intended for this purpose.2 At a glanceIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Technical features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Engine mechanical system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Ancillary unit drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Toothed belt drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Intake system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Cylinder block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Crankshaft drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Cylinder head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Camshaft adjustment system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Valve gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Lubrication system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Cooling circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Secondary air system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25Engine management system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 System overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Actuators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Functional diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Test your knowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373 IntroductionTechnical featuresDevelopment of the two V8 engines focussed primarily on the following development objectives: Compliance with future emission regulations Reducing fuel consumption Increasing torque and output Reducing the weight of the engine Improving operating comfort Off-road capability in the case of the TouaregS341_011Engine mechanical system- V8 cylinder block - Cylinder head with 5-valve technology and roller rocker fingers - Inlet camshaft adjustment - Two-stage variable intake manifold in the Phaeton - Three-stage variable intake manifold in the Touareg - Oil filter module - Twin-branch intake systemEngine management systemBosch Motronic ME 7.1.1 Sequential fuel injection Electronic ignition Two hot film air mass sensors Secondary air system One knock sensor per cylinder bank Two primary catalytic converter broadband lambda probes - Two transient lambda probes after the catalytic converter4 Technical dataEngine code Design type Displacement [cm3] Bore [mm] Stroke [mm] Valves per cylinder Compression ratio Maximum output Maximum torque Engine management system Fuel Exhaust gas aftertreatment Exhaust emission standard 228kW at 6200 rpm 410Nm at 3000 to 4000 rpm Bosch ME 7.1.1 RON 98, RON 95 with reduced output 4 catalytic converters, 4 lambda probes secondary air system EU 4 AXQ (Touareg) 8-cylinder V engine with a 90° V angle 4172 84.5 93 5 11:1 246kW at 6500 rpm 430Nm at 3500 rpm BGH (Phaeton)Torque and output graph 228kWTorque and output graph 246kW500 450 400 350 Torque [Nm] 300 250 200 150 100 50 0 2000 4000 6000 Engine speed [rpm]250 225 200 175 Output [kW] Torque [Nm] 150 125 100 75 50 25 0500 450 400 350 300 250 200 150 100 50 0 2000 4000 6000 Engine speed [rpm]250 225 200 175 150 125 100 75 50 25 0 Output [kW]S341_010S341_0125 Engine mechanical systemAncillary unit driveThe ancillary units are driven by means of a 7-groove poly-V belt. The ancillary unit drive fitted in the Phaeton differs from that in the Touareg due to an additional guide roller and the different layout of certain ancillary units.Touareg In the Touareg, the alternator and air conditioning compressor are installed in a higher location than in the Phaeton. As a result of this, the Touareg is capable of fording water up to a depth of 500mm.S341_087 Toothed belt guard Notch on vibration damper and mark on toothed belt guardTensioning element with belt tensionerS341_089 Belt pulley for air conditioner compressorBelt pulley for alternatorPoly V-belt 7-grooveBelt pulley for vibration damperGuide rollerBelt pulley for vane pump/power steeringPhaetonS341_088Belt pulley for vane pump/power steeringAn additional guide roller is required in the Phaeton because the alternator is fitted in a lower position than in the Touareg. This is due firstly to the installation space conditions in the Phaeton and secondly to the Touareg's necessary fording capability.Guide rollerBelt pulley for air conditioner compressor6 Toothed belt driveBoth exhaust camshafts and the coolant pump are driven by the crankshaft in the toothed belt drive. The toothed belt is tensioned via a belt tensioner and a hydraulic tensioning element.Locating plates with bores S341_091a S341_091bS341_090 Exhaust camshaft sprocket cylinder bank 1 Exhaust camshaft sprocket cylinder bank 2Hydraulic toothed belt tensioner guide rollerCoolant pump driving gearHydraulic toothed belt tensionerCrankshaft toothed belt sprocketBelt tensionerWhen renewing or replacing the toothed belt, the crankshaft must be set to TDC cylinder No. 5. To achieve this, the notch on the vibration damper must align with the mark on the toothed belt guard, and the locating plates' two large bores must face each other inwards. ELSA provides information on the detailed procedures for removing and installing the toothed belt.7 Engine mechanical systemIntake systemThe fresh air intake system has a twin-branch design to reduce pressure losses. Both intake tracts are brought together at the intake manifold upstream of the throttle valve module. A hot film air mass meter per intake tract and an intake air temperature sender in the air mass meter G70 are used to determine the intaken quantity of fresh air.Air mass meter G70 Intake air temperature sender G42 cylinder bank 1Throttle valve module J336Air mass meter 2 G246 cylinder bank 2S341_097Intake manifoldThe intake manifold is comprised of four bolted and bonded magnesium components. The Touareg is fitted with a three-stage variable intake manifold and the Phaeton with a two-stage variable intake manifold. In comparison with the three-stage version, the two-stage design allows intake tracts with high-volume cross-sections to be implemented. This leads to an increase in engine output.In the event of repair, the entire intake manifold has to be renewed, as the bonded surfaces can no longer be sealed.S341_0988 Variable intake manifoldThe figure shows the two-stage variable intake manifold fitted in the Phaeton. It is comprised of the variable intake manifold change-over valve, two vacuum units with adjusting levers, a non-return valve, the hoses and the vacuum reservoir in the front area of the vehicle. Change-over - From the torque position (long intake tract) to the output position (short intake tract) at 4600 rpm. - From the output position to the torque position at 4440 rpm.Variable intake manifold change-over valve N156 Adjusting leversS341_014Vacuum unitsNon-return valveTorque position Long intake ports are used in the torque position. This leads to a high flow speed, extensive turbulence in the cylinder, very good fuel/air mixing andrapid combustion. In turn, this results in the development of high torque.S341_015Output position Short intake ports with the largest possible crosssections are used in the output position. This results in high air throughput with good charging. In turn, this leads to high power output.S341_0139 Engine mechanical systemCylinder blockThe aluminium cylinder block has a 90° V angle and is manufactured from an aluminium alloy. The pistons run directly on the aluminium alloy's silicon crystals. As a result of this, no separate cylinder liners are required. The gap between cylinders is 90mm.S341_080Cylinder head gasketThe cylinder head gasket is a triple-layer metal gasket, whose outer layers are covered with a coating. Advantages: - Low settling behaviour - Long service lifeCoatingMetal layersS341_01610 Crankshaft driveCrankshaftSupported at five points, the crankshaft is forged from tempered steel. Two connecting rods are located on each crank pin. Due to different gearboxes, the crankshaft fitted in the 4.2l V8 5V engine in the Phaeton has an 8-hole pattern, and that in the Touareg a 10-hole pattern, to the drive plate.Phaeton crankshaft with 8-hole patternS341_021S341_025Connecting rodsThe connecting rods are machined as complete parts and are finally separated by a tool, exerting great force, to form the connecting rod and connecting rod bearing cap. This process is called "cracking".S341_023S341_026PistonsThe aluminium pistons are equipped with a valve pocket for the centre intake valve. Thanks to the valve pocket, the pistons are cylinder bank-specific.Valve pocketS341_02411 Engine mechanical systemCylinder headThe aluminium cylinder head has been developed as a cross-flow cylinder head. A good gas cycle and therefore a good cylinder charge are achieved as a result of this. The cylinder head houses the camshafts, the inlet camshaft drive and adjustment facility plus the valve gear with 5-valve technology.Inlet camshaft Drive chain for the inlet camshaftValve for camshaft adjustmentS341_076Exhaust camshaft Cross-flow cylinder headCylinder head coverDecoupling elementThe thin-walled cylinder head cover is manufactured from a die-cast magnesium alloy. Sealing between it and the cylinder head is achieved using rubber gaskets. As a result of this, there is no direct connection between the cylinder head cover and the cylinder head, and engine vibrations are not passed on to the cylinder head cover. The cylinder head cover is bolted using what are called decoupling elements.Cylinder head coverSpacer sleeveS341_022 Gasket Decoupling element Profiled rubber grommetCylinder head cover gasketELSA provides information on the detailed procedures for preventing cylinder head cover warping and guaranteeing reliable sealing.12 Camshaft adjustment systemThe gas exchange processes in the engine's combustion chamber exert a significant influence on output, torque and pollutant emission. The camshaft adjustment system allows these gas exchange processes to be adapted to the engine's relevant requirements. This is carried out by changing the valve opening and closing times, depending on the engine speed, with the aid of the inlet camshaft. In this case, the torque is increased in the lower to medium engine speed range, whilst output is raised in the upper engine speed range. Camshaft adjustment additionally improves internal exhaust gas recirculation. Adjustment equates to a crank angle of 22° in the "advance" direction.Tensioning piston Chain tensioner sliding shoe Oil reservoir chamber Hydraulic cylinder with switching pistonS341_033Inlet camshaft control valve 1 N205 Locking pin for starting phaseAdjustment pistonSliding shoe adjuster13 Engine mechanical systemHow it works:Depending on the manner in which the camshaft adjustment valve is actuated, the oil is guided into two different control ports. The ports are linked to the chambers on both sides of the adjustment piston. Adjustment in the "retard" direction takes place via port A, whilst adjustment in the "advance" direction occurs via port B.Basic position: From idle speed to approx. 1000 rpm Torque position: From approx. 1000 rpm to approx. 3600 rpm in the Touareg and approx. 5600 rpm in the Phaeton Output position: From approx. 3600 rpm in the Touareg and approx. 5600 rpm in the PhaetonBasic positionEngine off No oil pressure is available when the engine is switched off. The spring-loaded locking pin is pressed into the adjustment piston's detent groove, locking it. Starting the engine When the engine is started, the oil pressure is not yet sufficient to press the locking pin out of the adjustment piston's detent groove.Lubrication and breather bore Locking pinOil reservoir chamber S341_034Control portsAdjustment pistonThe locking function and the oil reservoir chamber in the camshaft adjustment unit reduce vibrations in the chain drive. Noise during the starting phase is minimised as a result of this.14 Engine running Once a specific oil pressure has been reached, the oil presses the locking pin - counter to the spring's force - out of the detent groove, and the inlet camshaft can be adjusted.Torque positionThe torque position is activated at an engine speed of between 1000 and 3600 rpm in the Touareg and 5600 rpm in the Phaeton. Via port B, the oil is conducted to the adjustment piston, pressing it into the torque position. In this position, inlet valve closing is advanced. This is advantageous, as the flow speed in the intake manifold is low in this engine speed range, and the fuel/air mixture follows the movement of the piston. Thanks to advanced inlet valve closing, the mixture can no longer be pushed back into the intake manifold by the cylinder.S341_038 Detent grooveLocking pinTorque position stopAdjustment pistonOutput positionAs of an engine speed of approximately 3600 rpm in the Touareg and 5600 rpm in the Phaeton, the system switches to the output position (basic position). Via port A, the oil is conducted to the adjustment piston, pressing it into the output position. In this position, inlet valve closing is retarded. Thanks to the high flow speed at these high engine speeds, the fuel/air mixture continues to flow into the cylinder, although the piston is already moving up again.S341_036Adjustment pistonOutput position stop15 Engine mechanical systemValve gearThe V8 engine is equipped with 5-valve technology. This offers a large flow crosssection and therefore ensures a very good gas cycle. The valves are actuated via roller rocker fingers with a hydraulic valve clearance compensation element.Camshaft roller chainCamshaft adjustment valveInlet camshaftRoller rocker fingerInlet valves Exhaust camshaftExhaust valvesS341_027Valve actuationThe valves are actuated by the camshafts by means of roller rocker fingers. The two exhaust valves are actuated via a twin roller rocker finger, and the three inlet valves via a triple roller rocker finger.Toothed belt Camshaft roller chainSingle-cam exhaust camshaft S341_029 Twin roller rocker finger Double-cam inlet camshaftTriple roller rocker finger16 The roller rocker fingers are mounted on an axle shaft. The axle shaft is used to simultaneously supply the bearings and the hydraulic valve clearance compensation elements with oil. - The hydraulic valve clearance compensation elements are located directly in the lever arm above the valves. - The rollers are each seated between the lever arms.Exhaust valvesInlet valvesSingle camTwin roller rocker finger Axle shaft with oil supplyDouble camHydraulic valve clearance compensation element Triple roller rocker fingerRoller seated between the lever arms Oil spray boreOil duct Exhaust valves 1 and 2 Inlet valves 1 and 3 Inlet valve 2 S341_032 S341_030Inlet roller rocker finger tolerance compensationMinor alignment and component tolerances may occur between the inlet camshaft cams and the roller rocker finger rollers. To guarantee even pressure between the components, the inlet roller rocker finger axle shaft is of a convex design. This prevents the roller rocker fingers from canting.Camshaft axis Inlet camshaftShaft axis (actual)Shaft axis (nominal) Rollers Axle shaft for roller rocker fingersS341_028Roller rocker fingersThe axle shaft's tolerance versus the camshaft is shown in grossly exaggerated form to depict it more clearly.17 Engine mechanical systemOil circuitThe oil circuit fitted in the 4.2l V8 5V engine in the Phaeton and the Touareg is primarily identical. However, the oil intake system differs due to the Touareg's off-road capability. The particulars of, and differences between, the oil circuits will be presented over the next few pages. The Figure shows the oil circuit fitted in the 4.2l V8 5V engine in the Phaeton.Cylinder bank 1 Inlet camshaft adjustment ThrottlesCylinder bank 2S341_084Oil retention valvesRoller rocker fingers Oil filter moduleCamshaftsSpray jet valve Bypass valves Filter element Oil pressure regulating valveOil pan upper sectionOil cooler Oil drain plug Oil pressure switchDuocentric oil pumpOil pan lower sectionOil without pressure Oil under pressure18 Duocentric oil pumpThe duocentric oil pump is bolted to the cylinder block and is driven by the crankshaft via a chain drive. The oil pressure regulating valve is integrated into the oil pump and regulates the engine's oil pressure.S341_042 Housing Outer rotorOil pressure regulating valveDrive shaft with inner rotor Housing cover with oil intake tubeOil filter moduleThe oil filter module is bolted onto the side of cylinder bank 1. It contains the oil filter element, the oil pressure switch and an oil cooler. The oil cooler is bolted onto the oil filter module and is connected to the coolant circuit. The oil filter module also houses the connections for cooling the alternator.Oil filter module Oil pressure switchS341_095Coolant supply Coolant supply to the alternator Coolant return from the alternatorCoolant supply from the engineOil return to the engineOil supply from the engine S341_094 Sealing cap S341_096 Oil cooler19 Engine mechanical systemOil panThe oil pan is comprised of two components; an upper oil pan section and a lower oil pan section. The oil pans in the Phaeton and the Touareg differ due to their differing requirements. The seal between the two parts and the cylinder block is achieved by means of a liquid silicone seal.Oil pan upper sectionPhaeton oil panThe upper section of the oil pan is manufactured from die-cast aluminium and the lower section of the oil pan from sheet steel. Due to the installation space conditions, the oil pan lower section is designed very flat and broad.Oil pan lower section S341_049Oil pan upper sectionTouareg oil panIn the Touareg, both parts are manufactured from die-cast aluminium. Higher stiffness is achieved in this way. Due to the vehicle's off-road capability requirements, the oil pan lower section is designed to be narrow and deep. Due to the low oil intake point and, in comparison with the Phaeton, lower oil level, guaranteed oil intake with little oil foaming is achieved on gradients.S341_051 Oil pan lower section20 Off-road capability measuresHousing Outer rotor Drive shaft with inner rotor S341_053 HousingOil pumpA two-stage oil pump is fitted to ensure that the engine is supplied with oil under all operating conditions, even off-road. This is comprised of the main oil pump and a so-called suction oil pump. Both pump gear sets are identical.Oil pressure regulating valve Inner rotor Outer rotor Housing cover with connection for rear oil intake tubeNormal travel and hill descentS341_050 Oil pan upper sectionDuring normal travel and hill descent, the majority of the oil is located in the lower section of the oil pan. The oil is intaken by the duocentric oil pump and pumped into the oil circuit.Oil pumpOil intake tubeHill ascentS341_052Suction oil pumpDuring hill ascent, part of the oil is located in the rear area of the oil pan upper section. It is now pumped into the lower section of the oil pan by the suction oil pump, where it is again intaken by the duocentric oil pump.Rear oil intake tubeOil pan upper section21 Engine mechanical systemCooling circuitThe Figure shows the cooling circuit fitted in the 4.2l V8 5V engine in the Phaeton with an auxiliary coolant heater.To the heating system heat exchangers Breather pipe Expansion tank Coolant temperature sender G62AlternatorHeater coolant shut-off valve N279Auxiliary coolant heater Oil filter module with oil coolerGearbox oil coolerWater pump V36Coolant pump Thermostat S341_054 Radiator outlet coolant temperature sender G83 RadiatorWater pump V36 The water pump ensures coolant circulation for the auxiliary coolant heater whilst the engine is switched off. Heater coolant shut-off valve N279 During auxiliary coolant heater operation, the shutoff valve disconnects the engine coolant circuit from the heating system heat exchangers in the vehicle's interior. Radiator outlet coolant temperature sender G62 and G83 Comparison between the two coolant temperature senders forms the basis of actuation of the electric coolant fans.Alternator Cooling the alternator via the engine coolant circuit protects it against overheating and therefore ensures a longer service life and better efficiency. Oil cooler The oil cooler is bolted onto the oil filter module; the coolant flows through it.22 Fuel systemThe Figure shows the fuel system fitted in the Phaeton. It differs slightly from the fuel system installed in the Touareg. The Touareg has a return-free fuel system, in which the fuel pressure regulator is installed in the fuel filter.Fuel pump G23Return pipeNon-return valve Auxiliary coolant heater supply pipe Fuel filter Supply pipe Filler hose from filler neckFuel pressure regulatorFuel railFuel system pressurisation pump G6 Injectors N83-N86 S341_055 Direction of travel Injectors N30-N33 Suction jet pumpsFiller hose from filler neck On fuelling, the fuel is pumped into the tank by the fuel system pressurisation pump G6. Electric fuel pumps Two fuel pumps are required due to the shape of the fuel tank. These pump the fuel to the fuel rail, to the suction jet pumps (fuel system pressurisation pump G6 only) and to the auxiliary coolant heater (fuel pump G23 only). Non-return valve This prevents fuel flowing from the fuel tank to the fuel pressure regulator.Suction jet pumps These are supplied with fuel by the fuel system pressurisation pump G6. The suction jet pumps then pump the fuel to each of the fuel pumps positioned opposite them. Fuel pressure regulator This is located on the fuel rail. A springloaded diaphragm valve regulates the fuel pressure to 4bar. During this process, the cross-section to the fuel return is enlarged or reduced depending on the pressure. Injectors These inject the fuel into the cylinders.23 Engine mechanical systemExhaust systemThe exhaust system is a twin-branch design. It is comprised of two catalytic converters beneath the bonnet, two flexible decoupling elements, two front silencers designed as baffled silencers, a centre silencer designed as an absorption silencer and two rear silencers designed as baffled silencers. The catalytic converters' substrate material is comprised of ceramic.Broadband lambda probe G108Broadband lambda probe G39 Primary catalytic converter Transient lambda probe after catalytic converter G130 Catalytic converters with front silencers Rear silencers Pipe convergence Decoupling elements Centre silencer Transient lambda probe after catalytic converter G131S341_061Pipe convergence The exhaust gases of both exhaust pipes converge upstream of the centre silencer. In this case, the sound waves overlap and noise emissions decrease.S341_06224 Secondary air systemJ220Supplied with current No current suppliedN112A G108G70 G39 B A+B G39 G62 G70 G108 J220 J299 N112 V101 Combination valves Lambda probe Coolant temperature sender Air mass meter Lambda probe 2 Motronic control unit Secondary air pump relay Secondary air inlet valve Secondary air pump motorG62V101 J299S341_064Due to the high level of mixture enrichment during cold starting and the warm-up phase, a high percentage of uncombusted hydrocarbons occurs in the exhaust gas in this period. The catalytic converter is unable to process this high percentage of hydrocarbons, because: - the catalytic converter has not yet reached its necessary operating temperature and - a lambda 1 mixture has to be present for full conversion to take place.Thanks to air injection downstream of the exhaust valves, the exhaust gases are enriched with oxygen, leading to oxidation (afterburning) of the hydrocarbons and the carbon monoxide. The heat released during this process additionally heats the catalytic converter, helping it to reach its operating temperature faster. The secondary air system is comprised of: - the secondary air pump motor V101, - two combination valves A + B and - the secondary air inlet valve N112.25 Engine management systemSystem overviewSensorsThe system overview shows the 4.2l V8 5V engine fitted in the Phaeton.Air mass meter G70 with intake air temperature sender G42 Air mass meter 2 G246S341_072Engine speed sender G28Hall sender G40, G163Lambda probe G39, G108 Lambda probe after catalytic converter G130, G131 Steering angle sender G85Throttle valve module J338 Throttle valve drive angle sender for electric throttle G187, G188ABS control unit J104Coolant temperature sender G62 Radiator outlet coolant temperature sender G83 Knock sensor G61, G66 Automatic gearbox control unit J217Accelerator position sender G79 Accelerator position sender 2 G185 Control unit with display in dash panel insert J285 Brake light switch F and brake pedal switch F47Kick-down switch F8Air conditioning system operating and display unitAuxiliary signals26 ActuatorsDiagnostic connection Fuel pump relay J17 and fuel system pressurisation pump G6 Electric fuel pump 2 relay J49 and fuel pump G23 Injectors N30, N31, N32, N33 N83, N84, N85, N86 Ignition coils with output stage N70, N127, N291, N292 N323, N324, N325, N326 Motronic control unit J220 with altitude sender F96Motronic current supply relay J271 Activated charcoal filter system solenoid valve 1 N80 Secondary air pump relay J299 Secondary air pump motor V101 Secondary air inlet valve N112 Throttle valve module J338 with Throttle valve drive (electric power control) G186 Inlet camshaft control valve N205, N208Continued coolant circulation relay J151 Water pump V36 Variable intake manifold change-over valve N156Lambda probe heater Z19, Z28 Lambda probe 1 and 2 heater after catalytic converter Z29, Z30 Radiator fan control unit J293, J671 with radiator fan V7, V177Auxiliary signals27 Engine management systemSensorsAir mass meter G70 with intake air temperature sender G42 and air mass meter 2 G246Due to the available installation space, the intake tract has a twin-branch design. Air mass meter G70 is installed along with intake air temperature sender G42 in the intake tract on the cylinder bank 1 side. Air mass meter G246 is installed in the intake tract on the cylinder bank 2 side. From the signals transmitted by the two air mass meters and the intake air temperature sender, the engine control unit calculates the mass and the temperature of the intaken air respectively.Air mass meter G70 Intake air temperature sender G42 Cylinder bank 1Air mass meter 2 G246 Cylinder bank 2S341_102Signal usageThe signals are used to calculate all load- and engine speed-dependent functions. These include the injection period, ignition timing or camshaft adjustment, for example.Effects in the event of failureIf an air mass meter fails, the throttle valve position and the engine speed are used as correction values. If the intake air temperature sender fails, a substitute value is assumed.28 Engine speed sender G28Engine speed sender G28The engine speed sender is secured to the gearbox housing. It samples a 60-2 sender wheel, which is secured to the drive plate. Based on these signals, the engine control unit detects the engine speed and the position of the crankshaft. A segment gap on the sender wheel serves the sender as a reference mark.Sender wheel with 60-2 reference markSignal usageThe signal is used to calculate the injection point, the quantity injected and the ignition timing. It is additionally used for camshaft adjustment and the activated charcoal filter system.Effects in the event of failureIn the event that the sender fails, the engine continues to run, but re-starting it is no longer possible.Drive plateS341_103Due to the different gearboxes which are fitted, the drive plate installed in the Phaeton is secured to the crankshaft with eight bolts and that in the Touareg with ten bolts.29 Engine management systemHall sender G40 and G163Hall sender G40 is located on cylinder bank 1, and hall sender 2 G163 is positioned on cylinder bank 2.Hall sender G40Signal usageThanks to the two hall senders, the engine control unit recognises the position of each cylinder bank's inlet camshafts. The signals are used for camshaft adjustment, and to calculate the injection point and the ignition timing.Effects in the event of failureNo further camshaft adjustment takes place if a hall sender fails. The engine continues to run and also restarts again after switching off thanks to run-on recognition.S341_099Hall sender 2 G163S341_08530 Knock sensors G61 and G66The 4.2l V8 5V engine is fitted with two knock sensors. Knock sensor 1 G61 is seated in the V on cylinder bank 1, and knock sensor 2 G66 is located on the outside on cylinder bank 2.Signal usageThe knock sensors detect knocking combustion. Regulation enables the ignition timing to be shifted towards the knock limit, therefore increasing the engine's efficiency.Effects in the event of failureS341_083If a knock sensor fails, the corresponding cylinder bank's ignition timing is adjusted in the "retard" direction. If both knock sensors fail, all of the cylinders' ignition timing is adjusted in the "retard" direction.S341_07931 Engine management systemActuatorsInlet camshaft control valve 1 N205 and inlet camshaft control valve 2 N208Both valves are bolted to the cylinder head. Inlet camshaft control valve 1 N205 is located on cylinder bank 1, and inlet camshaft control valve 2 N208 is positioned on cylinder bank 2.TaskDepending on actuation by the engine control unit, these have the task of adjusting the inlet camshafts. Inlet camshaft adjustment equates to a crank angle of 22° in the "advance" direction.Effects in the event of failureIf an electrical cable to the camshaft adjusters is defective or a camshaft adjuster fails, no further camshaft adjustment is carried out. Less torque is available.Inlet camshaft control valve 1 N205Inlet camshaft control valve 2 N208S341_100S341_10132 Variable intake manifold changeover valve N156The variable intake manifold change-over valve is secured to the intake manifold on the toothed belt side.TaskThis is a solenoid valve and is actuated by the engine control unit depending on load and engine speed. When this occurs, the valve either releases or seals the route from the vacuum reservoir to the vacuum units. The actuators then actuate the intake manifold change-over flaps and switch to the torque or the output position.S341_081 Vacuum unitsEffects in the event of failureVariable intake manifold change-over valve N156If the variable intake manifold change-over valve fails, intake manifold change-over is no longer possible. The intake manifold remains in the output position, and less torque is available.33 Functional diagramThe functional diagram shows the 4.2l V8 5V engine fitted in the Phaeton.30 1587aSSSSSSJ299N205N156N112N32N208N33N83N31N84N30N86N85N80V101AJ220N324N292N127N291N70N323N325N326F831S341_092aBattery Brake light switch Kick-down switch Brake pedal switch Fuel system pressurisation pump Fuel pump Engine speed sender Lambda probe Hall sender Intake air temperature sender Knock sensor 1 Coolant temperature sender Knock sensor 2 Air mass meter Accelerator position sender G83 G108 G130 G131 G163 G185 G186 G187 G188 G246 J17 J49 J151 J220 Radiator outlet coolant temperature sender Lambda probe 2 Lambda probe after catalytic converter Lambda probe 2 after catalytic converter Hall sender 2 Accelerator position sender 2 Throttle valve drive (electric power control) Throttle valve drive angle sender 1 for electric throttle Throttle valve drive angle sender 2 for electric throttle Air mass meter 2 Fuel pump relay Electric fuel pump 2 relay Continued coolant circulation relay Motronic control unitA F F8 F47 G6 G23 G28 G39 G40 G42 G61 G62 G66 G70 G7934 30 1587aSSSSSSaJ151F47FG70G42G246G39 / Z19V36J220J293J671V7 G79 G185V177J338 G188 G187 G18631S341_092bMotronic current supply relay Radiator fan control unit Secondary air pump relay Throttle valve module Onboard supply control unit Radiator fan control unit 2 Diagnostic connection Left brake light bulb Right brake light bulb Injector, cylinder 1 Injector, cylinder 2 Injector, cylinder 3 Injector, cylinder 4 Ignition coil 1 with output stage Activated charcoal filter system solenoid valve 1 Injector, cylinder 5 N84 N85 N86 N112 N127 N156 Injector, cylinder 6 Injector, cylinder 7 Injector, cylinder 8 Secondary air inlet valve Ignition coil 2 with output stage Variable intake manifold change-over valveJ271 J293 J299 J338 J519 J671 K M9 M10 N30 N31 N32 N33 N70 N80 N83Colour code/legend= input signal = output signal = positive = earth = CAN powertrain data bus35 Functional diagram30 1587a J519 S SaG130 / Z29G108 / Z28G131 / Z30J49J17J271G23G6J220K G163 G40 G28 G66 G61 G62 G8331S341_092cN205 N208 N291 N292 N323 N324 N325 N326 P Q S V7 V36 V101 V177 Inlet camshaft control valve 1 Inlet camshaft control valve 2 Ignition coil 3 with output stage Ignition coil 4 with output stage Ignition coil 5 with output stage Ignition coil 6 with output stage Ignition coil 7 with output stage Ignition coil 8 with output stage Spark plug connector Spark plugs Fuse Radiator fan Water pump Secondary air pump motor Radiator fan 2 Z19 Z28 Z29 Z30 1 2 3 K Lambda probe heater Lambda probe 2 heater Lambda probe 1 heater after catalytic converter Lambda probe 2 heater after catalytic converter Switch for CCS CAN data bus CAN data bus Diagnostic connectionColour code/legend= input signal = output signal = positive = earth = CAN powertrain data bus36 Test your knowledgeWhich answer is correct? One, several or all answers may be correct.1.What are the differences between the ancillary unit drives in the Touareg and the Phaeton? a) Due to the Touareg's off-road capability requirements, some of its ancillary units are positioned higher than in the Phaeton. b) The Touareg is fitted with a 5-groove poly-V belt and the Phaeton with a 7-groove poly-V belt. c) There are no differences.2.What has to be noted when changing the toothed belt? a) The notch on the belt pulley/vibration damper and the mark on the toothed belt guard must align. b) The large bores in the locating plates (camshaft sprockets) must be located opposite each other on the inner side. c) The small bores in the locating plates (camshaft sprockets) must be located opposite each other on the inner side.3.In how many stages is the variable intake manifold fitted in the 4.2l V8 5V engine in the Touareg and the Phaeton adjusted? a) Both engines are fitted with a two-stage variable intake manifold. b) The Touareg is fitted with a three-stage variable intake manifold and the Phaeton with a two-stage variable intake manifold. c) Both engines are fitted with a three-stage variable intake manifold.37 Test your knowledge4. What is the purpose of the suction oil pump fitted in the Touareg? a) The suction oil pump supplies the cylinder head with oil. b) The suction oil pump supplies the camshaft adjustment system with oil. c) When climbing hills, the suction oil pump pumps oil from the rear area of the oil pan upper section into the oil pan lower section, thereby ensuring that oil is supplied.5.Where is the engine speed sender installed? a) It is bolted centrally onto the cylinder block. b) It is secured to the gearbox housing, and samples a sender wheel on the drive plate. c) It is bolted into the cylinder block in the area of the toothed belt.6.What are the advantages of a camshaft adjustment system? a) Camshaft adjustment is used to improve output in the upper engine speed range and torque in the lower engine speed range. b) The camshaft adjustment system is used to improve internal exhaust gas recirculation. c) Camshaft adjustment is used to improve output in the lower engine speed range and torque in the upper engine speed range.7.What is the purpose of the secondary air system? a) Secondary air injection serves to increase performance in the partial load range. b) Secondary air injection serves to reduce exhaust emissions in the cold-starting phase. c) Thanks to secondary air injection during the cold-starting phase, the catalytic converter reaches its operating temperature faster.38 39Solutions 1. 2. 3. 4. 5. 6. 7. a) a), b) b) c) b) a), b) b), c) 341© VOLKSWAGEN AG, Wolfsburg All rights and technical changes reserved. 000.2811.56.20 Technical status 08.2005 Volkswagen AG Service Training VK-21 Brieffach 1995 D-38436 Wolfsburg❀ This paper has been manufactured from cellulose bleached without the use of chlorine.