TECHNICAL DOCUMENTATION
SSP 353 Occupant Protection – Passive Systems

This PDF is currently unavailable.
Read document text
Service TrainingSelf-study Programme 353Occupant Protection - Passive SystemsDesign and function… previously… todayS353_077The performance of motor vehicles has increased continuously in pace with their technical development. In combination with the simultaneous increase in vehicle density on the roads, this positive development has also led to increased driver attentiveness requirements. Despite the multitude of good ideas implemented, particularly in recent times, in the field of active road safety, accidents can never be ruled out or avoided entirely. Increasing research has therefore been conducted into technical possibilities for protecting vehicle occupants within the vehicle in the event of an accident. One initial step – implemented at the end of the 50s – was to restrain the occupants in their seats by means of seat belts in the event of a crash. At the beginning of the 80s, this progressed with the installation of airbags, which cushion the vehicle's occupants during a crash. These systems have been constantly extended and their functions improved. The interior equipment fitted in modern vehicles differs significantly from that of previous vehicle generations. In the illustration above, this can be clearly seen from the dash panel and the steering wheel, which are designed accordingly in addition to the integrated airbags.NEWImportant NoteThe self-study programme shows the design and function of new developments. The contents will not be updated.For current testing, adjustment and repair instructions, refer to the relevant service literature.2ContentsIn brief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 The occupant protection system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Historic outline of seat belt and airbag system development in automobiles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6General basics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 The passive occupant protection system . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 System component networking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Types of collision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Impact situation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Temporal sequence of a frontal collision . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Temporal sequence of a lateral collision . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Passive occupant protection systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Airbags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seat belt pre-tensioners . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Belt tension limiters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Head restraints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Child seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Roll-over protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Battery cut-off elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Market-specific features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 18 40 48 50 51 54 56 60 72Overview of self-study programmes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80Test yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 823In briefThe occupant protection systemThe overall occupant protection system is sub-divided into the two categories of active and passive safety. The following overview is intended to show which safety elements are assigned to active and which to passive occupant protection.Active safetyActive safety encompasses everything which may contribute towards preventing accidents wherever possible. This includes direct and comfortable steering, good running gear characteristics and coordination, good traction, effective brakes and hightorque engines. Fatigue-free seats, clear visibility, good climate control plus clear and uncomplicated controls and displays help to maintain the driver's safety. The active safety systems include the following systems, for example:● ● ● ● ● ●Anti-lock brake system – ABS Traction control system – TCS Electronic stabilisation programme – ESP Electronic brake pressure distribution – EBD Automatic cruise control – ACC Electronic differential lock – EDLS353_1044This self-study programme describes the passive occupant protection components, systems and functions fitted in Volkswagen vehicles.Passive safetyPassive safety refers to all design engineering measures which serve to protect vehicle occupants from injury and to minimise the risk of injuries in the event of an accident. The term particularly refers to collision behaviour and gives consideration to both personal protection and the protection of other road users in the event of an accident. The most important passive safety features in modern vehicles include:●●●● ●The seat belt system with seat belt pre-tensioners, including child restraint systems The airbag system, consisting of front, side and curtain airbags A rigid passenger compartment with corresponding roof stiffness plus crumple zones in the front, rear and side areas (These protect the occupants by specifically dissipating the impact energy.) Roll-over protection for cabriolets Battery cut-offS353_1055In briefHistoric outline of seat belt and airbag system development in automobiles1957195919681969Lap belts (static belt)3-point seat belts (static belt)Front head restraintsAutomatic seat belt retractorSeat belt development●Back in 1903, Frenchman Gustave Desiré Lebeau had a seatbelt, in the form of a shoulder belt which was applied crossways, patented. However, seat belts were not available until 1957. Initially installed only at the front, these were still pure lap belts, which held the body in the seat in the pelvis area. The upper body was not held in the seat, and was not therefore protected against a frontal crash. In 1958, Nils Bohlin patented the first 3-point seat belt. In 1959, the first automobile manufacturer fitted these seat belts as standard. With the 3-point seat belt, the entire upper body was restrained. Initially, these belts were still "static" and did not adapt to the body. The seat belt system was sensibly enhanced by head restraints, which were first implemented in 1968. The neck area was protected against overstretching on occupant movement to the rear after a crash and also in the event of rear impact. The launch of the automatic retractor as of 1969 meant that the seat belt was retracted under spring force and therefore always adapted itself to the body. In 1979, application of the seat belt on vehicle occupants' bodies was further improved by the new shoulder height adjustment facility. This enabled the upper anchorage point on the body to be adjusted so that the belt routing adapted very well to the relevant body size. In 1980 – in combination with a driver airbag – a seat belt pre-tensioner was introduced for the first time on the front passenger seat. In the event of an impact, this tensioned the looser belt and therefore ensured that the seat belt was positioned taut against the body. The system was additionally enhanced by belt tension limiters (seat belt loops, torsional limiters).●●●●●61979198019941998Shoulder height adjustmentFront airbags – driver airbag, seat belt pre-tensioner – front passenger sideSide airbagsCurtain airbagsAirbag development●A patent for an airbag was first registered in Germany by Walter Linderer in 1951. The patent was issued in 1953. It was only later – from 1980 onwards – that the first airbag was fitted as standard in an automobile (starting in the USA). High-volume airbags were used in the USA, as the wearing of seat belts was not a legal requirement. In Europe, lower-volume airbags were used, as seat belts were required to be worn by law. Airbags for the driver were introduced first, followed by passenger airbags. To protect against lateral impact, side airbags were introduced for the first time in 1994. Depending on equipment, these were fitted for the front and also the rear seats. This lateral protection was subsequently extended to the upper areas of the body. A so-called window airbag or curtain airbag was developed to achieve this. This stretched across the length of the window and protected the head area. Today, airbag development is particularly concerned with further developing deployment, the airbags' unfolding and the vehicle occupants' sinking into the airbags, in order to further reduce the risk of injury.●●●●It is important to know that wearing a seat belt is the No. 1 safety measure. All other measures enhance and increase safety, but only in combination with a seat belt which has been fastened.7General basicsThe passive occupant protection systemThe passive occupant protection system consists of:● ● ● ● ● ● ● ● ●Body Airbags Seat belts Seat belt pre-tensioners Belt tension limiters Seat design, poss. with active head restraints Child restraint systems Battery cut-off Control unit and sensor systemRight curtain airbagFront passenger side airbagFront passenger airbagThe illustration shows an example of a vehicle with a passive occupant protection system. Different equipment variants are possible depending on the vehicle model.Poss. crash sensor for front airbag on passenger sidePoss. crash sensor for front airbag on driver side Airbag control unitModel-specific information on the airbag systems can be found in the self-study programmes for the relevant vehicle models. An overview is available from page 80.8Rear right side airbagLeft curtain airbagRear left side airbagS353_006Crash sensor for rear side airbag, driver sideSeat belt pre-tensionerDriver side airbag Crash sensor for side airbag, driver side Driver airbagDue to reasons of clarity, the right-hand crash sensors and the seat belt pre-tensioner are not shown in the illustration. These are located as on the left-hand side of the vehicle.9General basicsSystem component networkingThe passive safety system may consist of the following components:● ● ● ● ● ● ● ● ●● ● ●●Airbag control unit Driver and front passenger airbags Side airbags Curtain airbags Crash detection sensors Seat belt pre-tensioners Belt tension limiters Roll-over protection for cabriolets Battery cut-off elements (only in vehicles in which the battery is installed in the interior/luggage compartment) Switches in the front seat belt buckles Seat occupied sensor, front passenger seat Key operated switch to deactivate the front passenger front airbag with relevant warning lamp Active head restraints on the front seatsThe adjacent system overview shows all possible passive occupant protection system components and their networking. Not all of these parts necessarily have to be fitted in each vehicle model. The convenience system central control unit is part of this overview, as it undertakes convenience functions such as e.g. switching on the hazard warning lights and unlocking the doors (in the event of a crash).Legend E24 E25 E224 Driver side belt switch Front passenger side belt switch Key operated switch to deactivate front passenger front airbag G128 Seat occupied sensor, front passenger side G179 Side airbag crash sensor on driver side G180 Side airbag crash sensor on front passenger side G256 Rear side airbag crash sensor on driver side G257 Rear side airbag crash sensor on front passenger side G283 Front airbag crash sensor for driver side G284 Front airbag crash sensor for front passenger side H3 Buzzer and gong J234 Airbag control unit J285 Control unit in dash panel insert J393 Convenience system central control unit J533 Data bus diagnostic interface (gateway) J623 Engine control unit K19 Seat belt warning system warning lamp K75 Airbag warning lamp K145 Front passenger side airbag deactivated warning lamp (PASSENGER AIRBAG OFF) N95 N131 N132 N153 N154 N196 N197 N199 N200 N201 N202 N250 N251 N252 N253 N309 N310 T16 Driver side airbag igniter Front passenger side airbag igniter 1 Front passenger side airbag igniter 2 Driver seat belt tensioner igniter 1 Front passenger seat belt tensioner igniter 1 Rear belt tensioner igniter on driver side Rear belt tensioner igniter on front passenger side Side airbag igniter on driver side Side airbag igniter on front passenger side Rear side airbag igniter on driver side Rear side airbag igniter on front passenger side Driver side airbag igniter 2 Driver side curtain airbag igniter Front passenger side curtain airbag igniter Battery isolation igniter Driver side roll-over protection solenoid (cabriolet only) Front passenger side roll-over protection solenoid (cabriolet only) 16-pin connector (diagnostic connection)10S353_00711General basicsTypes of collisionAccident analyses show that approx. half of all severe accidents and accidents involving injured occupants occur at the front of the vehicle. In this case, the forces act frontally to obliquely on the vehicle. A third of accidents primarily affect the left/right side of the vehicle. The rear end and roll-over are affected to lesser extents.S353_008Front51.1%Side32.0%Rear14.1%Roll-over2.8%Data source: GIDAS GIDAS (German in Depth Accident Study) is a joint venture project between the Federal Highway Research Institute and the Forschungsvereinigung Automobiltechnik e.V. (automobile technology research association). According to a random sample plan, some 2000 accidents per year are studied by two research teams in the areas of Hanover and Dresden. The data acquired in this way are regarded as statistically representative for answering many questions.12Impact situationThe various airbags serve to protect the occupants according to the relevant impact directions in the event of an accident. When the airbag control unit has detected a crash worthy of deployment, the systems are activated. Depending on the impact direction or angle, only certain airbags are activated. The airbag control unit also informs other vehicle systems of the crash event. This information is used to shut-off the fuel supply, etc. If a battery cut-off element is fitted, this is activated on airbag deployment.Crash – frontDepending on the severity of the accident, only the seat belt pre-tensioners or the seat belt pre-tensioners and front airbags for the driver and front passenger may be deployed.S353_069Crash – frontal offsetThe seat belt pre-tensioners or seat belt pre-tensioners and front airbags for the driver and front passenger and/or the relevant curtain airbags and/or the side airbags may be deployed.S353_070Crash – sideDepending on the vehicle model, the side airbags, curtain airbags and the seat belt pre-tensioners on the side of the vehicle affected by the collision may be deployed.S353_071Crash – rearDepending on the vehicle model, the seat belt pretensioners and the battery cut-off element may be activated.S353_20513General basicsTemporal sequence of a frontal collisionUp to a speed of e.g. 56 km/h, a period of approx. 150 milliseconds passes between the point in time of impact against a rigid obstacle and vehicle being stationary. Within this short period of time, a vehicle occupant has no opportunity to react. He participates passively in the accident sequence. Within this "blink of an eye",● ● ●The seat belt pre-tensioners, The relevant airbags and The battery cut-off (if fitted) must be activated.These individual actions are controlled by the airbag control unit. On completion of the protective function, the field of visibility to the front is cleared again by the airbag's collapsing.The illustration shows the principle sequence of driver and front passenger airbag and seat belt pre-tensioner deployment. Differences may occur depending on the vehicle model.14DriverFront passengerS353_00915General basicsTemporal sequence of a lateral collisionAs the crumple zone between the impacting vehicle and the occupants is very small, the protective measures must be introduced and carried out within the shortest possible time. The side and curtain airbags are therefore fully inflated within approx. 15 ms. To maintain the protective functions of the curtain airbags even in the event of a possible, secondary accident – e.g. following a lateral crash with the vehicle's rolling over – the curtain airbags remain inflated for longer.The illustration shows the principle sequence of side airbag, curtain airbag and seat belt pre-tensioner deployment. Differences may occur depending on the vehicle model.16S353_06717Passive occupant protection systemsThe airbagsFront airbagsDriver airbagThe driver airbag is inflated by what is called a pan-type gas generator. Its name is taken from its "pan-like" shape. This design form is particularly suitable for installation in the centre of the steering wheel. The generator is fitted as both a single-stage and two-stage version.Driver airbag inflatedS353_061The driver airbag's gas generator is integrated into a housing which is installed centrally in the steering wheel's impact absorber. This unit is also referred to as the airbag module.Work on airbag systems must only be carried out by trained personnel. In this regard, please also note the safety instructions in the current technical literature.18Front passenger airbagTubular gas generators are usually employed to inflate the front passenger airbag. These can be both solid fuel generators and hybrid gas generators. The generators are fitted as both a single-stage and two-stage version.Gas generator Front passenger airbag inflatedS353_062The front passenger airbag's gas generator is integrated into a housing which is installed in the upper right area of the dash panel. This unit is also referred to as the airbag module. To bridge the increased gap between the dash panel and front passenger in the event of a crash and offer good protection, the front passenger airbag has a different shape and a larger volume than the driver airbag.In the Transporter, both an individual seat and a double seat bench may be installed on the passenger side,whereby this is equipped with a wider airbag than the individual seat. If the vehicle is subsequently converted from an individual seat to a double seat bench or vice-versa, the front passenger airbag equipment must also be adapted accordingly.19Passive occupant protection systemsSide airbagsTubular gas generators are used to inflate the side airbags. The gas generators which are used are single-stage solid fuel or hybrid gas generators. The illustration shows a vehicle with all of its side airbags deployed. In the event of a lateral crash, however, only the airbags on the affected side of the vehicle are deployed.Front passenger side airbag inflated Gas generatorRear side airbag, front passenger side inflated Gas generatorDriver side airbag inflated S353_063 Gas generator Rear side airbag, driver side inflated Gas generatorThe airbag modules in the front seats are installed in the outer seat backrests. The airbag modules in the rear seats may be installed in the outer seat backrests or in the side trim.If the Transporter's front passenger seat is a rotating, individual seat, this seat must be turned in the direction of travel during vehicle operation.20Curtain airbagsTubular gas generators are used to inflate the curtain airbags. Due to the installation conditions, which are usually very constricted, the generators have a very slim design form. The gas generators which are used are single-stage hybrid gas generators. The illustration shows a vehicle with both curtain airbags deployed. In the event of a lateral crash, however, only the airbag on the affected side of the vehicle is deployed.Front passenger side curtain airbag inflated Gas lanceS353_064 Driver side curtain airbag inflated Gas generatorIn the curtain airbag module, the gas generator is connected to a gas lance, which serves to rapidly and reliably distribute the airbag inflation gas in the airbag. The gas lance is integrated into the curtain airbag. It may be designed as a metal tube or a fabric hose. Depending on the vehicle model, the gas generators may be installed in the front roof area beneath the sun visors, in the area of the B-pillar, between the C- and D-pillars and also in the rear roof area. The type and shape of the curtain airbags are also adapted to the relevant vehicle model.21Passive occupant protection systemsHead-thorax airbagsIn cabriolets, coupés and roadsters, so-called head-thorax airbags are fitted as side airbags. The airbag module's airbag is designed in such a way that it simultaneously acts as a side and curtain airbag. At Volkswagen, these airbags are fitted in the:● ● ●New Beetle saloon New Beetle cabriolet EOSThe head-thorax airbag shown in the New Beetle cabrioletHead-thorax airbagS353_10622The head-thorax airbag shown in the EOSHead-thorax airbag S353_09923Passive occupant protection systemsAirbag gas generatorsAt the start of airbag development, gas generators which operated according to the priciple of solid fuel combustion were used exclusively to inflate the airbags. Hybrid gas generators were also subsequently used in addition to solid fuel generators. If the airbag control unit detects a crash worthy of deployment, it activates the corresponding gas generators. Depending on the vehicle model, one- or two-stage gas generators may be used for the driver and front passenger airbags. In a one-stage gas generator, the entire gas generant is always ignited in one stage. In gas generators with two stages, the two gas generants are activated in succession following a time lag. The airbag control unit decides on the time gap between the two ignitions depending on the severity and type of accident. Depending on the vehicle, the lag may be between 5 ms and 50 ms. The second stage supplies the airbag with an additional volume of air. Both stages are always ignited. This prevents one gas generant from remaining active following airbag deployment (the exceptions are the US variants of the Phaeton and the New Beetle).Solid fuel generatorsThe solid fuel generators consist of a housing, into which a solid fuel charge with ignition unit is integrated. The structure and shape of the generator housing are adapted to the installation conditions. The generators are therefore distinguished according to their design form, e.g. pan-type gas generators and tube-type gas generators. The solid fuel is in tablet or ring form. Following ignition of the solid fuel, an inflation gas occurs; this is not hazardous to the vehicle occupants and consists of almost 100% nitrogen.Hybrid gas generatorsThe hybrid gas generators consist of a housing, into which a stored gas, which is compressed under high pressure, and a solid fuel charge with ignition unit are integrated. The structure and shape of the generator housing are adapted to the installation conditions. These generators are usually tubular. The main components are the pressure vessel with the airbag inflation gas and the gas generant (solid fuel) which is integrated into the pressure vessel or flanged onto it. The solid fuel is in tablet or ring form. The stored and compressed gas is a mixture of inert gases, e.g. argon and helium. Depending on the design of the gas generators, this is pressurised to between 200 bar and 600 bar. Ignition of the solid fuel opens the pressure vessel and leads to the occurrence of a gas mixture comprised of the solid fuel gas generant gas and the inert gas mixture.All non-ignited gas generators are hermetically sealed from the environment.24Gas generator for driver airbag,One-stage – solid fuel Due to its pan-like design form, this generator is also referred to as a pan-type gas generator. The ignition unit is located centrally in a round housing (pan). The solid fuel is distributed around this in a ring shape. A metal filter is installed between the solid fuel and the outer housing wall. The metal filter has the task of cooling and cleaning the gas which occurs. This ensures that the entire gas generant in the gas generator combusts and that no burning components enter the airbag. The generator is electricaly connected to the airbag control unit J234 via the coil connectors in the steering wheel unit.Generator – not ignited Gas generant Outlet aperturesMetal filterS353_102 Igniter Generator – ignitedGas to the airbag Gas to the airbagS353_103 Igniter activatedFunction● ● ●The igniter is activated. The gas generant is ignited and is burnt off abruptly. The gas which occurs flows through the metal filter into the airbag.25Passive occupant protection systemsTwo-stage – solid fuel Pan-type gas generators with two deployment stages are also fitted on the driver side.Generator – not ignitedHousing Gas generant 1Cap Gas generant 1 Metal filterS353_107 Nozzle bores Gas generant 2 Ignition charge Igniter 1 Igniter 226Generator – 1st deployment stage ignitedGas to the airbagGas to the airbagS353_108 Igniter 1 activatedFunction● ● ● ●Igniter 1 is activated. The ignition charge is ignited. This ignites the actual gas generant via the nozzle bores. The gas which occurs deforms the gas generator housing and enables the gas to flow out. The gas which occurs flows through the filter into the airbag.Generator – 2nd deployment stage ignitedGas to the airbagGas to the airbagS353_109Function● ●Igniter 2 activatedIgniter 2 is activated. The gas which occurs enters the airbag via the 1st stage combustion chamber and the metal filter.27Passive occupant protection systemsGas generator for front passenger airbag,Tubular gas generators are used for the front passenger airbags. They are therefore also called tube-type gas generators. One-stage – solid fuel The generator consists of a housing, into which an igniter, an ignition charge and a gas generant are integrated. A metal filter is installed between the gas generant and housing.Generator – not ignitedIgnition chargeGas generantIgniter S353_137 Outlet apertures Metal filterGenerator – ignitedIgniter activated S353_138 Gas to the airbagFunction● ● ●The igniter is activated. The ignition charge is ignited; this then ignites the actual gas generant. The gas which occurs flows through the metal filter into the airbag.28Two-stage – solid fuel (variant 1) The gas generator consists of a housing, in which two solid fuel gas generators, which are separated by a partition, are located.Generator – not ignitedRupture diskGas generant 1Filter diskGas generant 2 Igniter 2Igniter 1S353_012 Ignition charge 1 Spring Metal filter Separating disk Outlet apertures Ignition charge 2Generator – 1st deployment stage ignited Igniter 1 activatedGas to the airbagS353_139Function● ● ●Gas to the airbagIgniter 1 is activated. Ignition charge 1 is ignited; this then ignites gas generant 1 after breaking through the rupture disk. The gas which occurs flows through the metal filter into the airbag.Generator – 2nd deployment stage ignitedGas to the airbag Igniter 2 activatedS353_140FunctionGas to the airbag● ● ●Igniter 2 is activated. The further procedure occurs after deployment of the 1st stage. The gas which occurs flows through the metal filter into the airbag.29Passive occupant protection systemsTwo-stage – solid fuel (variant 2) The gas generant for the ignition charge consists of tablets. Hollow tablets are used for gas generant 1 and 2. The tablets' hollow design means that ignition of the entire gas generant is achieved faster.Generator – not ignitedIgnition charge 2Rupture diskOutflow aperturesRupture diskIgnition charge 1S353_110 Igniter 2 Gas generant 2 Metal filter Partition Gas generant 1 Compensation material Igniter 130Generator – 1st deployment stage ignitedGas to the airbag Igniter 1 activatedS353_111Gas to the airbagRupture disk openFunction● ● ●Igniter 1 is activated. Ignition charge 1 is ignited; this then ignites gas generant 1 after breaking through the rupture disk. The gas which occurs flows through the metal filter into the airbag.Generator – 2nd deployment stage ignitedGas to the airbagIgniter 2 activated Rupture disk open Gas to the airbagS353_112Function● ● ●Igniter 2 is activated. Deployment of stage 2 occurs after deployment of the 1st stage. The gas which occurs flows through the metal filter into the airbag.31Passive occupant protection systemsOne-stage – hybrid (variant 1) The one-stage hybrid gas generator consists of an ignition unit, a solid fuel charge and a compressed gas bottle.Generator – not ignitedSolid fuelRupture disk Projectile DetonatorS353_013Compressed gas bottleIgniterGas distributor pipe with outlet aperturesGenerator – detonator ignitedGas to the airbag Detonator activatedS353_090Gas to the airbagFunction● ●The detonator is activated. The projectile is accelerated and breaks through the rupture disk; the pre-compressed, cold gas in the compressed gas bottle begins to escape.Generator – gas generant ignited Gas to the airbagS353_091Gas to the airbagFunction● ●The projectile impacts onto the solid fuel charge igniter and ignites it. The gas mixture which occurs flows through the gas distributor tube and into the airbag.32One-stage – hybrid (variant 2) This one-stage hybrid gas generator consists of a compressed gas bottle in which an ignition unit is installed. This contains the igniter, the ignition charge and the actual gas generant.Generator – not ignited Ignition charge Gas generant Compressed gas bottleMetal filter IgniterS353_141Rupture diskOutflow aperturesGenerator – ignitedGas to the airbag Igniter activatedS353_142 Gas to the airbag Rupture disk openFunction● ● ● ●The igniter is activated. The ignition charge is ignited; this then ignites the gas generant. In the compressed gas bottle, the pressure increases until the rupture disk shatters. The gas which occurs flows through the metal filter into the airbag.33Passive occupant protection systemsTwo-stage – hybrid (variant 1) The structure of this two-stage hybrid gas generator corresponds to that of the one-stage hybrid gas generator described above. However, the gas generator has a second stage, consisting of an igniter, ignition charge and gas generant.Generator – not ignited Ignition charge 1 Igniter 1 Metal filter Gas generant 1 Compressed gas bottleS353_185Igniter 2 Ignition charge 2 Generator – 1st stage ignited Gas generant 2 Rupture diskOutflow aperturesGas to the airbagIgniter 1 activatedS353_186Function● ● ●Gas to the airbag Rupture disk openIgniter 1 is activated. Ignition charge 1 is ignited; this then ignites gas generant 1. The gas which occurs causes the pressure in the compressed gas bottle to increase until the rupture disk shatters, and flows through the metal filter into the airbag.Generator – 2nd stage ignited Gas to the airbagIgniter 2 activatedS353_187Function● ●Gas to the airbagIgniter 2 is activated. The further procedure occurs after deployment of the 1st stage; the gas mixture flows into the airbag.34Two-stage – hybrid (variant 2) The generator also has two separate solid fuel deployment stages. These are connected to a compressed gas bottle with integrated plunger system, in turn connected to a housing with outlet apertures for escaping airbag inflating gas.Generator – not ignited Gas generant 1 Igniter 1 Plunger Outlet aperturesIgniter 2 Seal diaphragm Gas generant 2 Generator – 1st stage ignited Igniter 1 activated Compressed gas bottleS353_015Gas to the airbagS353_079 Gas to the airbagFunction● ●Seal diaphragm openIgniter 1 is activated and gas generant 1 is ignited. The gas which occurs moves a plunger, which opens the compressed gas bottle's seal diaphragm; the gas mixture continues to flow into the airbag.Generator – 2nd stage ignitedGas to the airbagIgniter 2 activated S353_081 Gas to the airbagFunction● ●Igniter 2 is activated. The further procedure occurs after deployment of the 1st stage; the gas mixture flows into the airbag.35Passive occupant protection systemsGas generator for side airbagTubular gas generators are used for the front side airbags. One-stage – solid fuel The generator consists of a housing, into which an igniter, an ignition charge, the actual gas generant and a metal filter are integrated.Generator – not ignitedIgniterIgnition chargeGas generantMetal filterS353_113Outlet aperturesGenerator – ignitedGas to the airbagS353_134Gas to the airbag Igniter activatedFunction● ● ●The igniter is activated. The ignition charge is ignited; this then ignites the gas generant. The gas which occurs flows through the metal filter into the airbag.36One-stage – hybrid The generator consists of a housing with igniter, gas generant, metal filter and the axially flange-mounted compressed gas bottle.Generator – not ignited Gas generantMetal filterCompressed gas bottleS353_114 Igniter Rupture disk 1 Outlet apertures Rupture disk 2Generator – ignitedRupture disk 1 openRupture disk 2 openGas to the airbag Igniter activatedS353_135Function● ●●The igniter is activated and the gas generant is ignited. The gas which occurs breaks through the two rupture disks and mixes with the cold gas from the compressed gas bottle. The gas mixture flows out of the compressed gas bottle, through the metal filter and into the airbag.37Passive occupant protection systemsGas generator for curtain airbagTubular gas generators are used for the curtain airbags. One-stage – hybrid (variant 1) The generator consists of the compressed gas bottle, in which the igniter with gas generant is installed on one end and a metal filter with the outlet apertures to the gas lance is installed on the other side.Generator – not ignited Gas generant Compressed gas bottle Outlet apertures to the gas lanceS353_115 Igniter Rupture disk 1 Rupture disk 2 Metal filterGenerator – ignited Gas to the airbagGas to the airbag Igniter activated Rupture disk 1 open Rupture disk 2 open S353_136Function● ●●The igniter is activated and the gas generant is ignited. The gas which occurs breaks through rupture disk 1 and the pressure in the compressed gas bottle increases until rupture disk 2 breaks. The gas mixture now flows out of the compressed gas bottle, through the metal filter and into the airbag.38One-stage – hybrid (variant 2) A design form in which the igniter is installed in the side of the generator is alternatively available.Generator – not ignited Gas lanceGas generantFilterSupport Rupture diskIgniterS353_116 Compressed gas bottleFunction●Generator – ignited●●The igniter is activated and the gas generant is ignited. As a result of this, the support is mechanically fired out from its seat. The cold gas which is stored in the compressed gas bottle now breaks through the rupture disk and flows through the filter into the airbag.Gas to the airbagIgniter activated Rupture disk open S353_11739Passive occupant protection systemsThe seat belt pre-tensionersSeat belt pre-tensioners tension the belt in the event of a crash in the seat belt's direction of tension. This reduces belt slack (play between the seat belt and body). The belt therefore prevents the occupant from moving forwards (relative to the movement of the vehicle) at an early stage. A seat belt pre-tensioner is able to retract the seat belt by up to approx 130 mm within approx. 13 ms. If the counterforce acting on the seat belt is greater than the force of the seat belt pre-tensioner, seat belt pretensioning is ended. According to the structure and principle of operation of the seat belt pre-tensioners, a distinction is made between:● ● ● ● ●Cable-type seat belt pre-tensioners Ball-type seat belt pre-tensioners Wankel-type seat belt pre-tensioners Toothed rack-type seat belt pre-tensioners Strap-type seat belt pre-tensionersThese can be triggered both mechanically and electrically. Depending on a vehicle's level of equipment, these are fitted either only in the front or also on the rear seats.Mechanically triggered seat belt pre-tensionersCable-type seat belt pre-tensionersA mechanically triggered cable-type seat belt pretensioner is installed in the VW Polo up to YoM 1999, for example.Cable storeBeltThe system reacts mechanically at a specific deceleration value, and operates independently of the airbag control unit. The seat belt pre-tensioner unit forms a module with the belt inertia reel. The system is mounted in a protective tube on a bearing cap, similar to a vertical pendulum. A cable is secured to a plunger. The cable is rolled up in a cable store above the protective tube. The pre-tensioner unit consists of:Belt inertia reelCable Sensor springCable●●●The sensor system in the form of a spring mass system, A gas generator with pyrotechnical gas generant and A plunger with cable in the pressure tube.Plunger Gas generator Pressure tube Bearing cap Protective tube PlungerS353_029Sensor carrier40Ignition: If vehicle deceleration exceeds a specific value in the event of a crash, the sensor mass begins to move counter to the sensor spring force. The sensor mass consists of the sensor carrier, the gas generator with the pyrotechnical gas generant, the impact spring, the plunger and the pressure tube. If the sensor carrier has exceeded a specific travel on compression of the sensor spring, the gas generator, which is held by the sensor screw in its resting position, is vertically released. Due to the pretensioned impact spring, it is accelerated towards the impact pin in the impact plate. When the gas generator impacts onto the impact pin, the gas generator's gas generant is ignited.Impact plate with impact pinSensor screw Sensor springPlunger Pressure tube Gas generator Protective tube Sensor carrier Impact spring S353_030Tensioning: The gas rapidly flows into the pressure tube and pushes the plunger down with the cable. On initial movement of the cable, which is rolled up on the coupling plate, the toothed segment is shifted radially outwards from the coupling plate due to the acceleration force, and engages in the winding shaft's annular gear on the belt inertia reel.Winding shaft annular gear Toothed segment Belt inertia reel Coupling plateImpact spring CablePlungerS353_03141Passive occupant protection systemsA further variant of a mechanically triggered cable-type seat belt pre-tensioner is installed e.g. in the VW Sharan.Gas generator Bearing capPressed cable endPlungerPressure cylinderSensor massImpact bolt Impact spring Lock ball Sensor springSteel cableProtective tubeTransport lockS353_147The system is connected to the inertia belt reel via a tensioning cable. The mechanical sensor system and the pyrotechnical trigger are integrated into the trigger unit. The sensor system operates mechanically at of a specific deceleration value, and operates independently of the airbag control unit.42Deployment stepsABCDES353_143Function A The sensor unit, consisting of the sensor mass, pressure cylinder, plunger and gas generator, moves in the direction of travel until the lock balls engage radially past the sensor head. B Due to the lock balls' radial engagement, the gas generator is released and accelerated towards the impact bolt with the pre-tensioned impact spring. C When the gas generator impacts onto the impact bolt, the gas generant ignites. D Due to the ensuing pressure, the plunger separates from the sensor mass. E During the further course of expansion, the plunger carries the pressed cable end along and retracts the steel cable by up to max. 130 mm. The bearing cap is ejected.43Passive occupant protection systemsMechanically or electrically triggered seat belt pre-tensionersBall-type seat belt pre-tensionersMechanically or electrically triggered ball-type seat belt pre-tensioners are used at Volkswagen. The ball-type seat belt pre-tensioner consists of a compact unit, which encompasses the belt tension limiter in addition to seat belt fastened recognition facility. This seat belt pre-tensioner may be fitted on the front and rear seats. Mechanical triggering only takes place if the seat belt fastened recognition facility has detected a fastened seat belt.Ball collection container S353_016 Gear Storage tube with balls Pyrotechnical gas generant Deployment unit (mechanical or electric) BeltFunctionGas generantDeploymentThe seat belt pre-tensioner is driven by balls. The balls are stored in a storage tube. In the event of a crash, the gas generant is ignited by a deployment unit. In the case of the electrically triggered seat belt pretensioner, the deployment unit is activated by the airbag control unit.BeltS353_017Storage tube with ballsBelt coil carrierWhen the gas generant is ignited, the expanding gases set the balls in motion and drive them into the ball collection container via a gear. As the belt coil carrier is firmly joined to the gear, it is also rotated by the balls and the seat belt is tensioned.GearBall collection containerS353_01844Wankel-type seat belt pre-tensionersDeployment unitThe Wankel-type seat belt pre-tensioner operates according to the rotary piston principle.Rotary pistonBeltIt is usually installed in the area of the rear seats.DetonatorS353_019Function The 1st detonator is triggered mechanically or electrically. The expanding gas rotates the rotary piston. As the rotary piston is joined to the seat belt shaft, belt tensioning commences.Outlet channel1st detonatorOverflow channel S353_020Outlet channelOverflow channelAfter reaching a certain angle of rotation, the rotary piston releases the overflow channel to the 2nd detonator. The working pressure in chamber 1 ignites the 2nd detonator. The rotary piston continues to be turned. The combusted gas from chamber 1 escapes via the outlet channel.S353_0652nd detonatorChamber 1On reaching the 2nd overflow channel, the 3rd detonator is ignited due to the working pressure in chamber 2. The rotary piston continues to turn and the combusted gas from chamber 2 escapes via the outlet channel.3rd detonator S353_066 Chamber 245Passive occupant protection systemsElectrically triggered seat belt pre-tensionersToothed rack-type seat belt pre-tensionersThe toothed rack-type seat belt pre-tensioner forms a module with the belt inertia reel. Toothed rack-type seat belt pre-tensioners are used for the driver and front passenger seats. Function The signal from the airbag control unit ignites the gas generator's gas generant. The pressure which builds up causes the plunger, which is joined to the toothed rack, to move upwards. The toothed rack drives gears 1 and 2 via the pinion.Start of deployment Damping element Gear 1 Pinion Gear 2 Roller Torsion shaft Outer ring of the freewheel Plunger with toothed rack Gas generator S353_021End of deploymentGear 2 is firmly joined to the outer ring of the freewheel for the torsion shaft. If this outer ring now rotates, the rollers are pressed inwards until they jam between the outer ring and the torsion shaft, thereby achieving positive engagement. The rotational movement is now transferred to the torsion shaft, and belt retraction begins.Position of the rollers on positive outer ring/torsion shaft engagementRollers in home positionS353_02246Cable-type seat belt pre-tensionersThe cable-type seat belt pre-tensioner forms a module with the belt inertia reel. Cable-type seat belt pre-tensioners are used for the driver and front passenger seats.Plunger Not deployedProtective capTubeBeltS353_095Gas generatorIgnition of the gas generator leads to the creation of a gas mixture, which pushes the plunger with the attached cable upwards within a tube. Due to tensioning, the cable lies closely against the coupling plate connected to the retractor shaft and turns it in the direction of retraction.DeployedPlunger Tube Direction of retraction CableS353_096Coupling plateRetractor shaft47Passive occupant protection systemsBelt tension limitersTo prevent the loads which may act on the occupants in the event of an accident from becoming excessive, the belt inertia reels are equipped with belt tension limitation. As of a certain load level, the belt tension limiter extends the belt slightly and allows the occupant to sink into the airbag, which has already inflated.Belt stitched in the form of a loopA very simple technical solution for limiting the belt force is a seat belt stitched in the form of a loop. In the event of excessive tensile load, these seams tear open and the belt becomes longer. This reduces the tensile force and the load on the occupant.Belt stitching Belt clamp Stitched area of the beltS353_08248Torsion limiterThis belt tension limiter is installed in both the ball-type seat belt pre-tensioner, the Wankel-type seat belt pretensioner, the strap-type seat belt pre-tensioner and the toothed rack-type seat belt pre-tensioner. The belt's tensile load is limited by a torsion shaft in the belt coil carrier. Depending on the belt's tensile load, the torsion shaft is turned to a greater or lesser degree and therefore reduces peak loads.Belt coil carrier Belt The gear is joined to the torsion shaft on this side.The belt coil carrier is able to rotate freely in the gear's inner ring.S353_023The belt coil carrier is joined to the torsion shaft on this side.Torsion shaft runs in the belt coil carrier49Passive occupant protection systemsHead restraintsThe front seats are designed in such a way that the likelihood of curvical spine injuries (e.g. whiplash) are reduced. A distinction is made between active and passive systems in this case. In both systems, the risk of curvical spine injuries are reduced by reducing relative movement between the shoulder and head in the event of a rear impact.In passive systems, the risk of curvical spine injuries are reduced by the specific design of the entire seat, the head restraint and the distance between the head and head restraint without moving parts. Active head restraint The active head restraint is a purely mechanical system, which shifts the head restraint forwards to the head in the event of a rear impact. This reduces relative acceleration between the shoulder and head during a crash. The active head restraint system is a reusable system. Function If an acceleration force acts on the rear end of the vehicle in the direction of travel, the vehicle's speed increases in relation to that of the occupants. This difference in speed is the result of the occupants' mass inertia. . The occupants, who are pressed more intensively into the seat, increase the pressure on the lumbar plate in the seat backrest. The lumbar plate's movement is transmitted to the head restraint via a lever mechanism, and the head restraint is moved forwards to the head. As soon as the body pressure is reduced, the system is returned to its initial position via the tension spring.In active systems, the head restraint is moved towards the occupant in the event of a rear impact.System not activated"Active head restraint" functional unit Lumbar plateTension spring S353_068System activatedHead restraint moves forwardsBody pressureS353_08850Child seatsISOFIX systemIf vehicles are equipped with the ISOFIX system, separate child seats with ISOFIX brackets can be used. In this system, special brackets on the child seat are attached into the ISOFIX anchorage points in the vehicle. This connection securely holds the child seat in place. The two outer rear seats and also the front passenger seat can be used for the ISOFIX system.If child seats are to be used on the front passenger seat, the instructions in the owner's manual must be observed under all circumstances. Particular attention must be paid to deactivating the front passenger airbag when using child seats which face backwards.S353_027ISOFIX with Top TetherIn certain vehicle models, child seats with the ISOFIX system and an additional, upper retaining belt can also be used. This upper retaining belt is also called "Top Tether". The additional, upper belt secures the child seat better. The child seat is thereby held against the seat backrest and prevented from tipping forwards. The design may differ depending on the vehicle model. The illustration shows a Top Tether system in the VW Golf as of model 04. The upper retaining belt is attached to the child seat's two upper retainers. The other end of the belt is attached to a retainer, specifically intended for this purpose, on the rear wall of the luggage compartment. The eye is identified with the Top Tether symbol.Top Tether retainer S353_09251Passive occupant protection systemsIntegrated child seatsDepending on equipment, certain vehicle models may be fitted with integrated child seats for the two outer seats on the rear seat bench. These seats are suitable for children aged between 3 and 12 years. Thanks to their fixed installation in the vehicle seat, together with a correctly worn seat belt, integrated child seats offer children very good protection in the event of a crash.Integrated child seat in the rear seat benchIn addition to conversion to a normal seat (for adults), the child seat's raising mechanism also enables space-saving transportation of the child seat. Folding the seat cushion up raises the height of the seat. The side bolsters have to be folded up manually. When the seat cushion is folded down, the side bolsters automatically return to their original position. To prevent children's heads from falling to the side whilst sleeping, a lateral head restraint can be mounted beneath the head restraint on the rear seat bench, offering the body additional support.S353_025Lateral head restraint (can be mounted)Seat cushion not raisedRaising mechanismLateral bolsters, can be folded up S353_026 Seat cushion raised Footrest52Integrated child seat in the individual seatIn the VW Multivan, the integrated child seat is only available for the individual seat. A maximum of four individual seats with integrated child seat are possible per vehicle. The child seat fitted in the Multivan is suitable for children aged 9 months and over. To achieve this, a five-point seat belt system specifically optimised for young children is secured to the seat, guaranteeing secure and comfortable restraint. The child seat can be optimally adapted to any age level, from 9 months to adult.The following child seat settings are possible: A – Child seat with armrests folded down, adjusted for an adultS353_203B – Child seat with lateral head restraintC – Child seat with seat cushion folded up and lateral head restraintD – Child seat with seat cushion folded up, lateral head restraint and folded-down auxiliary seat cushion with five-point seat belt systemS353_20453Passive occupant protection systemsRoll-over protectionDue to their open-topped design, cabriolets are equipped with special elements which help to protect occupants in the event of accidents. This specifically includes the roll-over protection system. When deployed, the roll-over protection system creates a protective zone for the occupants in combination with the A-pillars.The roll-over protection system will be described using the New Beetle cabriolet as an example.Roll-over protectionS353_106The airbag control unit contains a sensor for detecting the vehicle's imminent rolling over. Together with other sensors installed in the control unit, the accident severity is determined and the roll-over protection and seat belt pre-tensioners are deployed. As soon as a seat belt pre-tensioner or airbag is triggered, the roll-over protection system is also deployed as a precaution in the event of a frontal, lateral or rear impact with high accident severity.54Function When de-energised, the roll-over protections are held in their lower position with a hook lever via the rollover protection solenoids N309 and N310. If the airbag control unit J234 detects a crash or the vehicle's imminent rolling over, the roll-over protection solenoids N309 and N310 release the roll-over system.Overall roll-over protection system – in initial positionS353_032Detent rail Pre-tensioned springRoll-over protectionRoll-over protection solenoid N309 or N310S353_033The pre-tensioned spring extends the roll-over protection within approx. 0.25 seconds, and the detent rail holds them in this position. After extending by just 80 mm, the roll-over protection can no longer be pushed back due to the detent rail. An active roll-over protection can be mechanically released and returned to its initial position.55Passive occupant protection systemsBattery cut-off elementsIf the starter battery is installed in the vehicle's interior or luggage compartment, a battery cut-off element may be fitted. The task of this cut-off element is to interrupt the cable from the starter battery to the starter and alternator. If the cable to the starter and alternator short-circuits in the event of an accident, possible vehicle fires are avoided via this cut-off. If an airbag is triggered during an accident, the battery cut-off element is also automatically activated. In a rear crash, the battery cut-off element is activated along with seat belt pre-tensioner deployment. The following components are used as battery cut-off elements:● ●Battery isolation igniter N253 in the battery safety terminal Battery cut-off relay J655 (with battery master/isolator switch E74)Battery isolation igniter N253 (variant 1)Battery safety terminals with an integrated battery isolation igniter N253 are installed in the Lupo 3L and the Phaeton. This pyrotechnical component helps to interrupt the cable between the starter battery and the starter. Function The battery safety terminal is secured directly on the positive terminal of the starter battery with a screw clamp. Ignition of the gas generant in the battery isolation igniter N253 and the resulting gases cause the conical pin to be pushed out from its initial position in the direction of the arrow.Initial positionStarter cable Battery isolation igniter N253 Positive terminal of starter batteryConical pinS353_036IgnitionConical pinPositive terminal of starter batteryS353_037 Screw clamp56After the conical pin has been moved due to the expansion of the gas, it is prevented from returning to its position by a counter bearing. The electrical connection between the starter battery and the starter therefore remains interrupted.Final positionCounter bearingS353_039The battery safety terminal with battery isolation igniter N253 receives an ignition signal from the airbag control unit J234. This signal is transmitted via a direct line from the airbag control unit J234 to the battery isolation igniter N253. As a result of this, the alternator's and starter's connection to the starter battery is interrupted. A B C J234 N253 TV - Starter battery - Starter - Alternator - Airbag control unit - Battery isolation igniter - Junction boxS353_12057Passive occupant protection systemsBattery isolation igniter N253 (2nd variant)Initial position A further pyrotechnical component with which the cable between the starter battery and the starter can be separated exists in addition to the battery safety terminal. Unlike the battery safety terminal, this component is based on interrupting a connector between the starter battery and starter connections. The battery isolation igniter N253 is installed in a separate plastic housing in the vicinity of the starter battery.Connector with connections PinIgniter S353_122Final position Function The ignition of a gas generant leads to combustion within the battery isolation igniter N253. The resulting gases move the plunger with pin in such a way that the contact between the starter battery and starter connections is interrupted.Connector with connections Pin with plungerIgniterThe battery isolation igniter N253 receives an ignition signal directly from the airbag control unit J234. As a result of this, the alternator's and starter's connection to the starter battery is interrupted. A B C J234 N253 TV - Starter battery - Starter - Alternator - Airbag control unit - Battery isolation igniter - Junction boxS353_123S353_12158Battery cut-off relay J655The battery cut-off relay J655 is a further component with which the cable between the starter battery and the starter can be separated. The battery master/ isolator switch E74 is additionally integrated into the battery cut-off relay. An activated battery cut-off relay J655 can be recognised via the viewing window. In the case of an interrupted cable, a white cover can be seen in the viewing window instead of a copper coil. The battery cut-off relay J655 must be renewed in this case.Battery cut-off relay J655Viewing windowS353_119The battery cut-off relay is triggered by the airbag control unit J234. In addition to actuation, the airbag control unit J234 also undertakes diagnostic monitoring and stores faults which have occurred. A B C E74 J234 J655 TV - Starter battery - Starter - Alternator Battery master/isolator switch Airbag control unit Battery cut-off relay Junction boxS353_118When deployed, battery cut-off elements and the battery cut-off relay J655, with and without reset button, must always be renewed. More detailed information can be found in the workshop manual applicable to the vehicle in ElsaWin.59Passive occupant protection systemsSystem managementAirbag control unit J234The electronics integrated into the airbag control unit J234 have the task of recording vehicle deceleration and vehicle acceleration and of recognising whether protection system deployment is necessary. External sensors are also used to record vehicle deceleration and vehicle acceleration during an accident in addition to the internal sensors in the airbag control unit J234. Only once the information from all sensors has been evaluated do the electronics in the airbag control unit J234 decide whether and when the safety components are activated. Depending on the type and severity of the accident, only the seat belt pre-tensioners or the seat belt pretensioners and airbags, for example, are deployed.The electronics in the airbag control unit J234 have the following main tasks:● ●● ● ●Crash detection (front, side, rear, roll-over*) Defined deployment of the seat belt pre-tensioners, airbags, battery cut-off and roll-over mechanisms* Seat belt warning (request to put on seat belts) Evaluation of all input information Permanent monitoring of the entire airbag system●●●●* for cabrioletStorage of faults and information on deployed protection systems Fault indication via airbag readiness indicator lamp Independent energy supply via capacitor for a defined period of time of approx. 150 ms Notification of a crash event to other system components via drive CAN or discrete crash output (wired conventionally)The steps required to renew an airbag control unit J234 can be found in the workshop manual applicable to the vehicle (ElsaWin) or in "Guided Fault Finding" or "Guided Functions".60Data exchangeThe airbag control unit J234 is integrated into the drive CAN. The airbag control unit transmits the following information on the drive CAN:● ● ● ● ● ● ●Airbag warning lamp K75 on/off Seat belt warning on/off Diagnostic data Crash signal Crash information for the final control test ESP data Front passenger airbag on/off statusAmongst other purposes, the information that a crash has taken place is used by other control units to release the central locking system, if locked, shut off the fuel supply and activate the hazard warning lights.Airbag warning lamp K75 The airbag warning lamp K75 indicates the functional readiness of the entire airbag system, as determined by the airbag control unit J234. A malfunction is indicated by constant illumination of the airbag warning lamp K75. In more recent models, actuation is carried out via the CAN bus. If the data message from the airbag control unit J234 is missing, the warning lamp is automatically switched on by the control unit in the dash panel insert J285.S353_15361Passive occupant protection systemsCrash sensorsInternal sensors in the airbag control unit J234A crash sensor and a safety switch are installed as internal sensors in the airbag control unit J234.Airbag control unit J234 – housing sealedCrash sensor The crash sensor is an acceleration sensor in the control unit; it records deceleration and acceleration in both the vehicle longitudinal axis (x axis) and the vehicle transverse axis (y axis).S353_157Safety switch In more recent control unit generations, the mechanical safety switch has been replaced by a micromechanical acceleration sensor. This sensor also records vehicle deceleration and acceleration in the direction of travel (x axis) and informs the control unit electronics of this for plausibility checks.Airbag control unit J234 – housing openRoll-over sensor A sensor for detecting roll-over may additionally be installed in the control unit, e.g. in a cabriolet.S353_15862External sensorsExternal sensors are also used in addition to the internal sensors in the airbag control unit J234. The following external sensors exist:● ● ●Front airbag crash sensor for driver side and front passenger side G283 and G284 Side airbag crash sensor on driver side and front passenger side G179 and G180 Rear side airbag crash sensor on driver side and front passenger side G256 and G257Front airbag crash sensors G283 and G284 The front airbag crash sensors for driver side and front passenger side G283 and G284 are installed to improve frontal crash detection. These sensors are acceleration sensors, which measure vehicle deceleration and acceleration in the longitudinal direction. Depending on the severity of the accident, this enables the airbags to be deployed earlier. Earlier deployment increases the occupant protection effect.Front airbag crash sensors G283 and G284S353_159Side airbag crash sensors G179 and G180 – acceleration sensors Both acceleration sensors and pressure sensors may be fitted as the side airbag crash sensors on the driver side and front passenger side G179 und G180. The acceleration sensors are usually installed in the area of the B-pillar connection to the sill. These sensors measure the vehicle's transverse acceleration and forward this information to the airbag control unit J234.Side airbag crash sensor on driver side G179B-pillarS353_15563Passive occupant protection systemsSide airbag crash sensors G179 and G180 – pressure sensors The pressure sensors are installed in the right and left front doors. On deformation of the doors, the air pressure is increased for a short time. This pressure increase is recorded by the sensor and forwarded to the airbag control unit J234.Pressure sensor (side airbag crash sensor on driver side G179)S353_160Rear side airbag crash sensors G256 and G257 The rear side airbag crash sensors G256 and G257 are acceleration sensors. These sensors are installed in the vehicle in the area of the right and left C-pillar. Their task is to measure the vehicle's transverse acceleration and forward this information to the airbag control unit J234.C-pillarRear side airbag crash sensor on driver side G256S353_15664Function of the crash sensors – acceleration sensors A crash sensor essentially consists of a housing, evaluation electronics and a micromechanical acceleration sensor.Evaluation electronicsAcceleration sensorIn simplified terms, the acceleration sensor is designed like a capacitor. Some of the capacitor plates are fixed. Their counterparts are movably mounted and work as a seismic mass.Resting position Movable capacitor plate CrashS353_161Recording directionFixed capacitor plateIf the seismic mass is moved in the direction of recording in the event of an accident, the capacitor's capacity changes. This information is evaluated by the evaluation electronics, digitally processed and transmitted to the airbag control unit.S353_162 Evaluation electronics65Passive occupant protection systemsFuntion of the crash sensors – pressure sensors In the event of a lateral crash, the crash sensors measure the abrupt change in air pressure in the front doors. There are two types – a capacitive and a piezo-electric pressure sensor. Both types of sensor are in the sensor unit with evaluation electronics, which are installed together in one housing.Piezo-electric pressure sensor The piezo-electric pressure sensor unit consists of a sealed cavity, over which a diaphragm with piezo crystals is tensioned. Via pressurisation, the diaphragm is pressed in and a movement occurs in the piezo crystals. This movement is processed as a voltage by the evaluation electronics and transmitted as a signal to the airbag control unit J234.DiaphragmLay