TECHNICAL DOCUMENTATION
SSP 361 Audi Q7

This PDF is currently unavailable.
Read document text
Service TrainingAudi Q7Self-study programme 361The Audi Q7In superior fashion, the Audi Q7 combines sportiness and versatility, advanced technology and premium-class luxury. On the road, it excels with the driving performance and dynamics of a sports car, while redefining the possibilities of its class off-road. A vehicle which visually display all its qualities and meets its promise in technological terms, on any road and under any conditions. Audi Q7 – the high-performance SUV from the creator of quattro. The very design of the Audi Q7 sets new standards. Characteristic of the typical Audi dynamism are the swooping curve of the roofline and the distinctive relationship between the high waistline and narrow window area. The dynamic sweep of the front section and the powerful rear with the sharply sloping D-pillars provide a coupe-like profile. Equally characteristic elements of the current Audi styling are the shoulder line and dynamic line which define the side section.361_000Taking the lead: With design & performanceContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Passenger protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Running gear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Electrical system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Air conditioning system . . . . . . . . . . . . . . . . . . . . . . . . . . 54Infotainment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68The self-study programme provides basic information on the design and function of new vehicle models, new vehicle components or new technologies. The self-study programme is not intended as a workshop manual. The specified values only serve for better understanding and relate to the software versions applicable at the time the SSP was compiled. For maintenance and repair operations it is essential that you refer to the current technical literature.NoteNoteIntroductionIn a nutshellSome Audi Q7 dimensions.361_045361_0465-seater Admissible total weight in kg Unladen weight without driver in kg Drag coefficient Cw Tank capacity in litres Trailer weight, braked (on 12 % uphill gradient) in kg Nose weight in kg Combination weight (12 %) in kg Admissible roof load in kg 4.2l FSI 3.0l TDI 100 4.2l FSI 3.0l TDI 4.2l FSI 3.0l TDI 0.37 100 3500 140 6495 6550 3200 130 6365 6420 2895 2950 2240 2295 3065 3120 2270 23256/7-seater4Interior dimensions361_103Luggage compartment volume775 l 330 l361_105361_1042035 l361_1065IntroductionBodyThe body of the Audi Q7 has been newly developed by Audi and is not based on a predecessor SUV model. During the development process, the most significant properties and characteristic values were initially defined. For example:● ● ● ● ● ●body weight torsional and bending values crash performance scheduled development time scope of simulation and prototype development planned insurance categorySignificant features of the Audi Q7 body shell are a high overall rigidity as well as optimised local bending and torsional values at the body nodes and force application areas.Bodyshell361_055The development● ● ●of an open sky system, an optional third seat row,The self-supporting, lightweight steel body of the Audi Q7 is built in four bodyshell versions:● ● ● ●Normal roof Normal roof with three seat rows Panorama roof (open sky system) Panorama roof (open sky system) with three seat rowsa tailgate with integrated rear lights, which wraps around to the rear side panel, were further important features. The focus was on combining these elements with the typical Audi high quality expressed, for instance, in the dimensional accuracy of the body parts, the narrow gap widths and surface finish.The Audi Q7 with three seat rows is equipped with an additional cross-piece in the spare wheel well area for attachment of the seat belts. On the versions with the panorama roof, the cross-pieces at the B and C-pillars are dispensed with. Their function is fulfilled by the open sky module.6Joining techniquesIn order to meet the high demands with regard to body rigidity, crash safety and optimised production processes, the following joining techniques are employed on the Audi Q7: – – – – – Spot welding Spot weld bonding MAG welding Laser soldering Plasmatron soldering The bonded joints, with a length of 79815 mm, comprise 5403 spot welds. The total length of the laser-soldered joints (seamless joints between roof and side frame) amounts to 4420 mm. As with the Audi A3 Sportback and the Audi A6 Avant '05, the side panel and the rain channel are joined using plasmatron soldering. Like laser soldering, this technique ensures a high-quality and a virtually invisible seam. The length of the left and right joints amounts to 1438 mm. The length of the MAG welded joints, used in areas which are inaccessible using welding tongs, amounts to 15272 mm.The joining technique most frequently employed for areas subject to high loads is spot weld bonding using a structural adhesive.Adhesive Plasmatron soldering Laser soldering Spot welding (not shown) MAG welding (not shown)361_0577BodyMaterialsIn addition to the joining techniques employed, selection of the correct materials is vital for achieving both crash safety and body rigidity. Depending on loading and weight, the most suitable material is determined for each component. The proportions of the individual materials used are as follows: – Standard steels 36 % – High-strength steels 26 % – Higher-strength and super high-strength steels 32 % – Aluminium 6% The sill tube consists of a rolled section because the manufacturing tolerances are lower in this case than for an extruded tube, enabling smaller wall thicknesses. In order to meet pedestrian protection requirements, plastic parts are used in the plenum chamber/bulkhead area.The wing panels, bonnet and tailgate are made of aluminium, making them some 22 kilogrammes lighter than their steel counterparts. The weight was further reduced through the use of various semifinished products*. With tailored rolled blanks, for example, the wall thicknesses can be adapted to withstand differing component loading. The reinforcements for the rear longitudinal members and the floor cover panel are made from tailored rolled blanks.* Semi-finished products: Pre-processed materials for the manufacture of parts and components8Standard steels High strength steels Higher-strength and super high-strength steels Aluminium361_0569BodySeat conceptThe Audi Q7 seats up to seven occupants. As standard, the Audi Q7 is equipped with five seats. The Audi Q7 can optionally be fitted with electrically-adjustable seats for the driver and front passenger. A memory function is also available for the front seats. The backrests of the driver and front passenger seats have been ergonomically designed such as to reduce to distance between the occupant's head and the head restraint. The headrest must be adjusted correctly for this purpose. The seats in the second seat row can be individually adjusted longitudinally and offer occupants the most generous leg room in this vehicle class. Where the Audi Q7 is equipped with a third seat row, the second seat row features an easy-entry function and longitudinal seat adjustment. In the 6-seater equipment version, comfort seats are optionally available for the second seat row.Audi Q7 with seven seatsAudi Q7 with six seats361_050Audi Q7 with five seats361_052Note Please refer to the owner's manual for information on operation of the vehicle seats.361_04910The head restraints of the second seat row do not prevent the backrests from folding. When the head restraints of the second seat row are lowered, the backrests do not fully reach the load floor position. When folding down the backrests of the third seat row, the head restraints lower automatically, making it easier to fold down the backrests. If the seats in the second and third seat roads are unoccupied, the head restraints can be lowered by hand in order to improve rearward visibility.The easy-entry function on the second seat row is operated via a lever next to the head restraint. The backrest folds forwards to a certain angle. The seat base also moves in the direction of travel. The easyentry function enables the occupants to enter and exit the third seat row.361_051Attachment of the seat belts to the seats of the third seat row is achieved via additional belt buckles. The advantage is that the seatbelts can be removed from the seats as required. The seat belts are retracted and the latch plates can be inserted in the D-pillar trim. In this manner, the seat belts are protected against damage during loading of the luggage compartment when the backrests are folded down. The central belt buckles are attached to the vehicle floor.Persons above a height of 160 cm are prohibited from being seated in the third seat row.361_04411Passenger protectionPassenger protection in the Audi Q7Owing to its wide range of use, the Audi Q7 represented a special challenge for the development team: A high degree of passenger protection during both on-road and off-road operation. In meeting these requirements, the Audi Q7 fits seamlessly into the high safety level of the current Audi model range. The passenger protection system of the Audi Q7 comprises the following components and systems: – – – – – – – – – – – Airbag control unit Driver and front passenger airbag, dual stage Front side airbags Sideguards (curtain airbags) Crash sensors for front airbag, the so-called upfront sensors for frontal impact detection Crash sensors at the B-pillars for side impact detection Crash sensors at the C-pillars for side impact detection Front belt tensioners Battery isolation igniter Switch in front-seat belt buckles Seat occupied sensor in front passenger seatSide airbags for the second seat row and a key operated switch for deactivation of the front passenger airbag with the corresponding warning lamp are also available as optional equipment. Owing to the various requirements and statutory regulations placed upon vehicle manufacturers by the markets, the equipment versions may vary, particularly with regard to the US market.Key E24 Driver side belt switch E25 Front passenger side belt switch E224 Key operated switch to deactivate front passenger side airbag G128 Seat occupied sensor, front passenger side G179 Side airbag crash sensor on driver side (B-pillar) G180 Side airbag crash sensor on front passenger side (B-pillar) G256 Rear side airbag crash sensor on driver side (C-pillar) G257 Rear side airbag crash sensor on passenger side (C-pillar)12361_001G283 Front airbag crash sensor for driver side (front end, left) G284 Front airbag crash sensor for front passenger side (front end, right) J234 J285 J393 J533 J623 Airbag control unit Control unit in dash panel insert Convenience system central control unit Data bus diagnostic interface (gateway) Engine control unitN95 N250 N131 N132 N153 N154 N199 N200 N251 N252 N253 T16Driver side airbag igniter Driver side airbag igniter 2 Front passenger side airbag igniter 1 Front passenger side airbag igniter 2 Driver seat belt tensioner igniter 1 Front passenger seat belt tensioner igniter 1 Side airbag igniter on driver side Side airbag igniter on front passenger side Driver side curtain airbag igniter Front passenger side curtain airbag igniter Battery isolation igniter Connector, 16-pin (diagnostic connection)K19 Seat belt warning system warning lamp K75 Airbag warning lamp K145 Front passenger side airbag deactivated warning lamp (PASSENGER AIRBAG OFF)13Passenger protectionAirbag control unit J234The purpose of the electronics integrated in the airbag control unit is to detect vehicle deceleration or acceleration and to evaluate it so as to detect a vehicle impact. In order to detect vehicle deceleration or acceleration during an impact, external sensors are used in addition to the sensors installed inside the control unit. The electronics in the control unit detect a crash based alone on the information received from the sensors. Only once all the sensor information has been evaluated by the control unit electronics can the electronics decide when and which safety components should be activated. The airbag control unit is able to detect frontal, side and rear impacts. A further task of the airbag control unit is to activate the relevant restraint systems (belt tensioners or belt tensioners and airbag) depending on the type and severity of the impact as well as signalling the crash to other vehicle systems.The airbag electronics have the following main tasks: – Crash detection (front, side, rear) – Defined triggering of the belt tensioners, airbags and battery isolation igniter – Defined triggering of the second front airbag stage – Evaluation of all input information – Permanent monitoring of the complete airbag system – Independent power supply via a capacitor for a defined time (approx. 150 ms) – Fault display via a failure warning lamp – Storage of fault and crash information – Communication of a crash to the other system components via the drive CAN or discrete crash output (conventional wiring) – Activation of seat belt warning system361_007For information on which components must be replaced following an accident, please refer to the applicable Workshop Manual in ELSA. An airbag control unit can only be replaced with the aid of an online-capable VAS 5051 or VAS 5052. The guided fault-finding or guided function applications must be used for this purpose. The airbag control unit must be coded and adapted to the relevant vehicle. If coding or adaption is not performed correctly, this may result in malfunctions in other vehicle systems, e.g. the ESP.14Data exchangeThe airbag control unit is connected to the drive CAN.The airbag control unit transmits the following information via the drive CAN: – Activation of warning lamp K75 – Activation of seat belt warning system – Diagnostic data – Crash signal – Crash information for the control element test – ESP data – Front passenger airbag activated/deactivated status (display in dash panel insert) The airbag control unit evaluates the following information from the data bus: – Dimming for the front passenger side airbag deactivated warning lamp (Passenger Airbag Off) The information that a crash has occurred is used by other control units in order to unlock a locked central locking system, cut off the fuel supply, activate the hazard warning lights etc.Airbag warning lamp K75Activation of the airbag warning lamp, which is located in the dash panel insert J285, is performed via the CAN bus. In the absence of a data message from the airbag control unit, the warning lamp is switched on automatically by the dash panel insert.Rear impact recognitionDuring a rear impact, the vehicle is strongly accelerated in the direction of travel. The crash sensors in the airbag control unit and the crash sensors G283 and G284 detect this vehicle acceleration and transmit the relevant signals to the airbag electronics. The airbag electronics evaluate the information. If the sensor signals exceed a specified value, the belt tensioners are triggered and the battery isolation igniter is activated.15Passenger protectionSeat belt warning systemThe Audi Q7, like the Audi A6 ´05 for example, features a seat belt warning function for the driver and front passenger. When the ignition is switched on, the airbag control unit evaluates the information from the driver and front passenger belt buckle switches as well as information from the front passenger side seat occupied sensor. The airbag control unit detects whether the front passenger seat is occupied or not based on the resistance values of the front passenger side seat occupied sensor. If the driver or front passenger have not fastened their seat belts, they are alerted via the seat belt warning system warning lamp K19 in the dash panel insert and an audible signal.Timing diagrams for the seat belt warning system Visual and audible signals – seat belts are fastened lateTerminal 15On Off v 10 km/h v 10 km/h Yes No OnVehicle speedFastenedSeat belt warning system warning lamp Off On Audible signal Off Time 361_016Visual and audible signals – seat belts not fastenedTerminal 15On Off v 10 km/h v 10 km/hVehicle speedFastened No On Off On Audible signal Off Time 361_018 min. 90 sec.Seat belt warning system warning lampThe warning is reactivated if the seat belt status changes during "terminal 15 on".16Seat occupied sensor, front passenger side G128The front passenger side seat occupied sensor consists of a plastic film incorporating several individual pressure sensors. The front passenger side seat occupied sensor is located in the front passenger seat, between the seat cover and padding. The seat occupied sensor extends across the rear part of the front passenger seat and is positioned such that the relevant area of the seat surface is monitored. Depending on the load, the resistance value of the front passenger side seat occupied sensor is modified. When the front passenger seat is not occupied, the resistance value of the front passenger side seat occupied sensor G128 is high. As the load increases, the resistance value falls. Above a load of approx. 5 kg, the airbag control unit detects "seat occupied".The airbag control unit requires the information from the front passenger seat occupied sensor G128 and from the belt buckle switches for the seat belt warning system.361_017Resistance value of G128 Evaluation approx. 430 Ohm and higher approx. 140 Ohm and lower Seat not occupied Seat occupied17Passenger protectionBelt switchDriver side belt switch E24 Front passenger side belt switch E25(In the driver and front passenger side belt buckles) Information as to whether or not the driver and front passenger have fastened their seat belts is required by the "seat belt warning system" function. In order for the airbag control unit to receive this information, the belt switches E24 and E25 are integrated in the belt buckles for the front seats. The switches fitted are reed switches. The reed switches switch from "switch open" to "switch closed" through the action of an external magnetic field. The magnet 1 in the so-called spring thorn is located near the reed switch when the latch plate is not inserted, i.e. the reed switch is closed.361_019When the latch plate is inserted in the belt buckle, the spring thorn is moved. The magnet 1 in the spring thorn no longer acts upon the reed switch, i.e. the reed switch is open. Based on the measured resistance value, the airbag control unit recognises whether the seat belt is fastened or not.Spring thornSpring thornReed switch Spring thorn Reed switch361_020361_021361_034 Magnet I361_041361_04018Driver seat belt tensioner igniter 1 - N153 Front passenger seat belt tensioner igniter 1 - N154The front seats of the Audi Q7 is equipped with the proven compact tensioners. The belt tensioners work according to the "ball gear" principle (not USA) and are triggered electrically by the airbag control unit. During a crash, the belt tensioners are activated before the front airbags. To prevent excessive loads to the occupants, the belt reels are equipped with belt force limiters. Above a specified load level, these force limiters slacken the belt, allowing the occupant to move forwards into the already deployed airbag. In the event of a side impact with side airbag triggering, the relevant belt tensioner is also triggered. In the event of a rear impact, the belt tensioners are also activated, depending on the severity of the impact.Seat belt361_053Key operated switch to deactivate front passenger side airbag E224The key operated switch to deactivate front passenger airbag E224 and the corresponding front passenger side airbag deactivated warning lamp K145 (PASSENGER AIRBAG OFF) are required in order to deactivate the front passenger airbag. An illuminated front passenger side airbag deactivated warning lamp K145 (PASSENGER AIRBAG OFF) indicates to the occupants that the front passenger airbag is deactivated. The control unit unequivocally recognises the switch position by means of the arrangement of four resistors which are connected in-line, pair-wise. If the airbag control unit detects a faulty key operated switch, a fault memory entry is made and the front passenger side airbag deactivated warning lamp K145 (PASSENGER AIRBAG OFF) begins to flash.Airbag control unit J234361_02519Passenger protectionAirbagThe front airbags on the driver and front passenger sides are equipped with two-stage gas generators. Depending on the nature and severity of the accident, the airbag control unit sets a time delay between the two ignitions (from approx. 5ms to 30 ms). The loads which the driver and front passenger are exposed to during a crash can be reduced by means of a delayed ignition of the propellant charges. Both propellant charges are ignited in all cases. This prevents a propellant charge from remaining active following airbag deployment.Driver airbagN95 Driver side airbag igniter I N250 Driver side airbag igniter IIThe gas generator in the driver airbag works using two pyrotechnic propellant charges.Priming chargeHousingCapMetal filterMetal filterPropellant charge IPropellant charge IBores Igniter I Igniter IIPropellant charge II 361_014The driver's airbag gas generator is flexibly mounted in a rubber ring. This minimises any vibration at the steering wheel. The gas generator acts as a vibration damper.20Driver side airbag igniter I - N95The electrical igniter I, which is activated by the airbag control unit, ignites the priming charge I. This ignites the actual propellant charge I via the bores. When the gas pressure generated through combustion of the propellant charge I exceeds a specified threshold, the housing of the gas generator becomes deformed, opening up a passage to the airbag via the metal filter. The airbag is deployed.Priming charge IHousingMetal filterMetal filterPropellant charge IPropellant charge IBores 361_015 Igniter IDriver side airbag igniter II - N250Following a defined delay, the airbag control unit energises the second electrical igniter, which directly ignites the second propellant charge. At a certain pressure, the generated gas lifts up the cap of the second stage and flows into the airbag via the combustion chamber of the first stage.CapPropellant charge IIMetal filterMetal filterCombustion chamber Propellant charge ICombustion chamber Propellant charge IIgniter II 361_01321Passenger protectionFront passenger airbagN131 Front passenger side airbag igniter I N132 Front passenger side airbag igniter IIThe front passenger airbag module housing is made of plastic.361_008A two-stage hybrid gas generator is used on the passenger side. Two pyrotechnic propellant charges are contained in a compressed gas cylinder, which is activated separately by the airbag control unit. The so-called cold gas in the compressed gas cylinder is under a pressure of approx. 250 bar and is a mixture of argon (approx. 98 %) and helium (approx. 2 %). The airbag volume is approx. 140 litres. The coil springs ensure that the propellant charge tablets are held in position (pretension).Priming charge IPropellant charge ICoil springFilterIgniter IIgniter IIPriming charge IIPropellant charge IICoil springBurst discCompressed gas cylinder Gas: Argon, approx. 98 % helium, approx. 2 % Pressure: approx. 250 bar 361_00222Front passenger side airbag igniter I - N131The airbag control unit energizes the igniter I and the priming charge I is ignited. This in turn ignites the actual propellant charge I. The combustion gas generated increases the pressure in the compressed gas cylinder until the burst disc breaks at a predetermined pressure value. The gas mixture reaches the airbag via the metal filter and it is deployed.Priming charge IPropellant charge ICoil springBurst discFilterIgniter I361_003Front passenger side airbag igniter II - N132The operating principle of the second stage is identical to that of the first. An additional volume of gas is supplied to the airbag through combustion of the second propellant charge. There is no further increase in pressure inside the airbag during the second stage.FilterIgniter IIPriming charge IIPropellant charge IICoil springBurst disc 361_00423Passenger protectionSide airbagsN199 N200 N201 N202 Side air bag igniter on driver side Side air bag igniter on front passenger side Rear side airbag igniter on driver side Igniter for rear side airbag on passenger sideThe side airbags for the first seat row are the same as the modules installed in other Audi models in terms of design and function. However, they have been adapted to the passenger compartment concept of the Audi Q7. For the first time, so-called "soft-cover modules" have been used for the side airbags on the second seat row. With these modules, the usual plastic casing has been replaced by a fabric cover. In addition to its low weight, the advantage of this cover is better integration into the backrest due to its soft surface. In some markets, the side airbags for the second seat row are optional equipment.First seat row side airbagsIf the airbag control unit J234 detects a side impact which fulfils the triggering criteria, it energises the relevant side airbag igniter. Only the side airbags on the vehicle side where the impact has occurred are activated.Second seat row side airbags361_006In the first seat row, the gas generators used are tubular pyrotechnic gas generators; in the second seat row, hybrid gas generators are used.361_00524Side airbag igniter on driver side N199 Side airbag igniter on front passenger side N200The relevant side airbag igniters are energised by the airbag control unit. The priming charge then ignites the propellant charge. The combustion gas generated flows through the metal filter into the airbag. The airbag is deployed.Priming chargeMetal filterVentIgniterPropellant chargeVent 361_022Rear side airbag igniter on driver side N201 Rear side airbag igniter on front passenger side N202The propellant charge is ignited by the igniter. The generated gas breaks both burst discs and becomes mixed with the cold gas contained in the cold gas cylinder. The gas mixture flows through the metal filter into the airbag, deploying it.Fabric cover361_066IgniterPropellant chargeFilter tube with ventsBurst disc IBurst disc IICold gas cylinder Gas: argon, approx. 97 % helium, approx. 3 % Pressure: approx. 240 bar 361_03725Passenger protectionCurtain airbag(sideguard)Driver side curtain airbag igniter N251 Front passenger side curtain airbag igniter N252In order to better protect occupants in the event of a side impact, the curtain airbag covers virtually the complete side window area from the A to the D-pillar. In the case of these modules, the hybrid gas generator is installed in the front roof area. The airbag is filled via a gas lance. A cold gas mixture of helium (approx. 80 %) and argon (approx. 20 %) is used, which is stored at 300 bar in a compressed gas cylinder. When the airbag control unit ignites the propellant charge, burst disc I breaks due to the pressure generated. The pressure in the compressed gas cylinder increases. When a certain pressure is reached, the gas breaks burst disc II and penetrates into the airbag via the filter and the gas lance. The airbag volume is approx. 40 litres.361_010Burst disc IBurst disc IIFilter361_009 Propellant charge Compressed gas cylinder Gas: helium, approx. 80 % argon, approx. 20 %Deployed sideguard361_011 26Battery isolation igniter N253The battery isolation igniter serves to disconnect the starter and alternator cable from the vehicle battery in the event of a crash. Activation is performed by the airbag control unit. Whenever an airbag or belt tensioner is triggered, the battery isolation igniter is also activated. When the pyrotechnic propellant charge is ignited, the gas pressure generated pushes the pin, which is attached to a piston, breaking the connection between the two terminals. The battery isolation igniter must be replaced following activation. Diagnostic monitoring is performed by the airbag control unit J234. In the Audi Q7, the battery isolation igniter N253 is installed in an electrics box beneath the front left seat.361_033Battery isolation igniterBattery isolation igniter activatedPinPin with pistonIgniterIgniterConnecting element with terminals361_023Connecting element with terminals361_02427Passenger protectionSupplementary passenger protection system features for the North American marketIn order to meet the statutory and market-specific requirements for the US market, the Audi Q7 is equipped with a special seat occupied sensor for the front passenger seat and a roll-over detection system.Roll-overAn additional sensor for roll-over detection has been integrated into the airbag control unit J234. If vehicle roll-over is detected, the belt tensioners and curtain airbags are activated.Front passenger side seat occupied sensorIf the airbag control unit J234 receives the information that the front passenger seat is not occupied or that a child seat is installed, the airbag control unit switches off the front passenger airbag. A deactivated front passenger airbag is indicated to the occupants via illumination of the front passenger side airbag deactivated warning lamp (PASSENGER AIRBAG OFF) and a message in the dash panel insert.The system essentially comprises the following components: – – – – – – – – Seat padding Seat occupied sensor mat Pressure sensor for seat occupied recognition G452 Seat occupied recognition control unit J706 Front passenger side belt switch E25 Seat belt force sensor for seat occupied recognition G453 Front passenger side airbag deactivated warning lamp K145 (PASSENGER AIRBAG OFF) Airbag control unit J234Front passenger side airbag deactivated warning lampSeat paddingFront passenger side belt switch Airbag control unit Seat belt force sensor for seat occupied recognition Pressure sensor for seat occupied recognition Seat occupied sensor mat Seat occupied recognition control unitConnector under the seatCut-off point 361_027The positions of the components installed are specified and must on no account be changed. Neither may individual system components be exchanged. Please proceed exactly in accordance with the instructions contained in the applicable Workshop Manual and the guided fault-finding.28Seat occupied recognition control unit J706The seat occupied recognition control unit J706 evaluates the signals from the pressure sensor for seat occupied recognition G452 and seat belt force sensors for seat occupied recognition G453. The signal from the seat belt force sensor for seat occupied detection provides information on how high the tension force is on the seat belt. Based on the signal from the pressure sensor for seat occupied recognition, the seat occupied recognition control unit determines the load on the front passenger seat. If the load is below approx. 20 kg and a very low or no belt force at all is detected, the presence of a child seat is identified by the seat occupied recognition control unit and communicated to the airbag control unit. The front passenger airbag is deactivated by the airbag control unit. If the load on the seat is e.g. 25 kg and the belt force exceeds a specified value, the seat occupied recognition control unit recognises that additional pressure is being applied by the child seat onto the seat cushion via the seat belt. The control unit recognises a the presence of a child seat and the airbag control unit deactivates the front passenger air bag. Above a load of approx. 25 kg and a low belt force, the seat occupied recognition control unit assumes that the seat is occupied by an adult and the front passenger airbag remains activated. When the ignition is switched on, the sensor information is evaluated continuously. This ensures that the seat occupied recognition control unit detects and reacts to any changes in seat occupancy. In order to prevent the load changes occurring during driving operation from resulting in immediate deactivation of the front passenger airbag, the system operates with a certain delay during driving. An acceleration sensor installed in the seat occupied recognition control unit communicates vehicle movements to the electronics.Seat loadLess than approx. 20 kg E.g. 25 kg More than approx. 25 kgBelt forceVery low or none Very high LowRecognitionChild seat Child seat AdultData exchange between the airbag control unit J234 and the seat occupied recognition control unit J706 is performed via the LIN bus. Diagnostic monitoring is performed by the airbag control unit.29Passenger protectionSeat belt force sensor for seat occupied recognition G453The seat belt force sensor for seat occupied recognition is integrated in the front passenger seat belt buckle. It basically consists of two parts which move in relation to one another and a Hall sensor, which is located between the magnets I and II. A calibrated spring holds the parts in the initial position. In this position the magnets I and II do not act on the Hall sensor. When the seat belt is correctly fastened, a tensile force is applied at the belt buckle. The distance between the Hall sensor and magnets I and II changes. The action of the magnets on the Hall sensor and consequently the voltage signal of the Hall sensor also changes. The higher the tensile force on the belt buckle, the more the parts move towards one another. The seat occupied recognition control unit receives this information and evaluates it. A mechanical stop ensures that the sensor element is not torn apart in the event of a crash.Initial positionTensile force appliedMagnet I Hall sensor Magnet IISpring361_038361_03930Belt switchDriver side belt switch E24 Front passenger side belt switch E25 The belt switches (reed switches) are installed in the belt buckles of the front seats. As long as the latch plate is not inserted in the belt buckle, magnets I and II act on the reed switch. The magnetic forces of the two magnets cancel each other out. The reed switch is open. The magnet I is located at the tip of the moveable spring thorn. The magnet II is permanently attached to the housing, as is the reed switch. When the latch plate is inserted in the belt buckle, the spring thorn moves with the magnet I. The magnet II alone acts on the reed switch. The reed switch is closed.Spring thorn Spring thornMagnet IIMagnet IMagnet IIMagnet IReed switch361_036Reed switch361_035Spring thorn361_034 Magnet I 361_043 361_042Two resistors are integrated in the circuit. Depending on the position of the reed switch, measurement takes place via one or both resistors. Based on the measured resistance value, the airbag control unit recognises whether the seat belt is fastened or not.361_02931Passenger protectionPressure sensor for seat occupied recognition G452The pressure sensor for seat occupied recognition G452 and the seat occupied sensor mat are integrated in a single component. The seat occupied sensor mat is filled with a silicone-like gel and is located under the seat padding of the front passenger seat. When the front passenger seat is occupied, the pressure in the seat occupied sensor mat changes. This pressure change is detected by the pressure sensor for seat occupied recognition and is communicated in the form of a voltage signal to the seat occupied recognition control unit J706. Depending on the load, the voltage ranges between 0.2 V (high load) and 4.8 V (low load). The seat occupied recognition control unit supplies the pressure sensor with a voltage of 5 V.361_028Note The replacement part (service kit) seat occupied sensor (USA) is pre-calibrated; the components must always be installed together. The service kit consists of: - Seat occupied recognition control unit J706 - Pressure sensor G452, - Seat-occupied sensor mat, - Seat padding, - Wiring harness between seat occupied recognition control unit J706 and pressure sensor G452. The pressure hose and the seat occupied sensor mat must never be kinked during assembly.32Driver seat belt tensioner igniter 1 - N153 Front passenger seat belt tensioner igniter 1 - N154In the Audi Q7 for the North American market, belt reels with newly-developed belt tensioners, socalled rack-and-pinion belt tensioners, are used for the driver and front passenger. For the second seat row, the familiar ball gear belt tensioners are used on the outer seats. Triggered electrically by the airbag control unit, the pyrotechnic propellant charge drives a piston with an integral rack. This, in turn, is connected to the torsion shaft (belt shaft) via gears and a free-wheel. The vertical movement of the rack is converted into a rotary motion via the gears. The rack drives the gears I and II via the pinion. The gear II and the outer race of the free-wheel for the torsion shaft are permanently attached to each other. When the outer race is turned, the rollers are pressed inwards until the outer race and torsion shaft engage positively. The torsion shaft then turns and belt tensioning begins. Tensioning ends as soon as the piston with the rack reaches the damping element or the counterforce exerted by the seat belt exceeds the force of the propellant charge. During normal operation, the belt reel is isolated from the tensioner unit by the free-wheel.Rollers in initial position Outer race of the free wheel Torsion shaft Initial positionDamping element Gear 1 Pinion Gear 2RollerOuter race of the free wheelTorsion shaftPiston with rack Gas generator361_030361_031After triggeringPosition of rollers upon positive engagement of outer race/ torsion shaft361_03233EngineEngine/gearbox combinationsFor the market introduction of the Audi Q7, only the 3.0l V6 TDI and the 4.2l V8 FSI engines will be available in conjunction with the (09D) 6A 6-speed automatic gearbox.Note For the design and function of the power transmission, please refer to the self-study programme SSP 363 Audi Q7 - Gearbox.3.0l V6 TDI common rail injection engineAL 750 6A 6-speed automatic gearbox4.2l V8 FSI direct injection petrol engineAL 750 6A 6-speed automatic gearbox361_107Two petrol engines featuring FSI technology and a common rail diesel engine in conjunction with the ML 400 6-speed manual gearbox and the AL 420 and AL 750 6-speed automatic gearboxes will also be available at a later date.344.2l V8 FSIThe engine number is located in the inner V of the engine block at the left cylinder head.Technical features– – – – – Chain drive on the power take-off side Selective FSI petrol direct injection Individual pencil ignition coils 2 primary and 2 main catalytic converters 4 Lambda probes361_126Torque / power curve Torque in Nm Power output in kWEngine speed in rpm361_047Technical dataEngine code letters Design Capacity Output Torque Bore Stroke Compression Distance between cylinders Weight Firing order Engine management Exhaust gas recirculation system Exhaust-emission control Emission standard BAR V8 petrol engine, 90° V angle 4163 cm3 257 kW (350 PS) at 6800 rpm 440 Nm at 3500 rpm 84.5 mm 92.8 mm 12.5:1 90 mm approx. 198 kg 1-5-4-8-6-3-7-2 Bosch Motronic MED 9.1.1 Internal exhaust gas recirculation 2 primary catalytic converters, 2 main catalytic converters EU 435Engine3.0l V6 TDI Common RailTechnical features– Chain drive on the power take-off side – Common rail injection system with 1600 bar injection pressure – 8-hole piezo injectors – Turbocharger with variable turbine geometry – Steel glow plugs – Diesel particulate filter361_110Torque / power curve Torque in Nm Power output in kWEngine speed in rpm361_048Technical dataEngine code letters Design Capacity Output Torque Bore Stroke Compression Distance between cylinders Weight Firing order Engine management Exhaust gas recirculation Exhaust-emission control Emission standard BUG V6 diesel engine, 90° V angle 2967 cm3 171 kW (233 PS) at 4000 rpm 500 Nm from 1750 to 2750 rpm 83 mm 91.4 mm 17.0:1 90 mm approx. 221 kg 1-4-3-6-2-5 Bosch EDC 16 CP Cooled exhaust gas recirculation, switched Oxidation catalytic converter, Lambda probe, particulate filter EU 4363.0l V6 TDI modificationsLateral inclination The oil supply in the engine must be ensured during extreme off-road situations. For this reason, in the case of the Q7, the oil sump and oil suction pipe have been designed and modified so that sufficient oil can be supplied to the pump even in the case of extreme lateral inclination of the vehicle. Additional baffle plates are integrated in the upper section of the sump in order to retain the oil. Owing to a deeper sump lower section, the oil suction pipe always remains submerged in the oil.361_108Oil pumpUpper section of sump with baffle plate functionLower section of sumpOil suction point361_109Note Extraction of the engine oil is not permitted on this engine.37Engine4.2l V8 FSICrankcaseWith a length of 430 mm and a width of 520 mm, the 90° V cylinder crankcase is very compact. The bore diameter is of 84.5 mm and the distance between cylinders is 90 mm. Cylinder liners have been dispensed with in order to achieve a wall thickness of 5.5 mm between the cylinders. The finish-machining of the aluminium cylinder barrels is performed by means a three-stage honing and erosion process.Cylinder crankcase, upper sectionBearing bridgesCylinder crankcase, lower section361_120Note For information on design and function, please refer to the self-study programme SSP 377.38Oil circuitThe oil supply is based on a classic wet-sump concept. It has been possible to reduce the delivery rate of the oil pump through optimisation of the crankshaft bearings. For this reason, the oil remains in the sump for longer, improving degassing. In order to ensure a low oil temperature, an oil/water heat exchanger is used, which is located on the oil sump in front of the engine. The oil filter module is maintenance-free and is installed in the inner V of the engine. The filter element is easy to replace without special tools. It is made of a polymer fleece.Oil filter with polymer fleecePressure oil channelsOil/water heat exchangerMain oil galleryOil pump driven by chain drive D361_11139EngineFuel systemTwo demand-controlled single-plunger high-pressure pumps are used in the fuel system, which are driven by a double cam on each of the inlet camshafts. In comparison with a constant delivery pump, the drive power is reduced depending on the rail pressure. The operating pressure is between 30 and 100 bar.Fuel pressure sender for low pressure G410 High pressure pump with fuel metering valve N290 and N402361_112 Fuel pressure sender G24740Fuel tankIn terms of the tank bladder, the fuel tank is the same component for petrol and diesel engines. Its useful volume is approx.103 l. The main differences are to be found in the fuel tank breather system and the inside of the fuel tank. Further differences, such as the tank leak diagnosis system are dependent on the use of the vehicle in the various countries. An appropriately designed fuel tank breather system ensures easy refuelling and prevents the fuel tank from leaking following vehicle roll-over. Fuel filling level measurement is the same for petrol and diesel engines. In this case, magnetically passive position sensors (MAPPS) are used. One sensor is fitted in each chamber.Activated charcoal filter Leak diagnosis pump (USA only)Bubble containerBreather valveBreather pipesNon-return valveFlange with electrical connection for MAPPS senders, fuel filter and fuel tank breather system361_078Note The operating principle of the MAPPS is described in detail in the self-study programme SSP 282.41EnginePetrol engineHere, a fuel delivery unit is fitted in the fuel tank. It is located in the right main chamber. In order to also deliver fuel from the left chamber, the delivery unit drives two suction jet pumps, which pump the fuel into the delivery unit. The fuel system pressurisation pump G6 is controlled by the fuel pump control unit J538 and generates a pressure of between 3.5 and 5.5 bar. The fuel filter is installed in the left flange connection. The active charcoal filter is located behind the fuel filler neck.Diesel engineHere, a fuel delivery unit is fitted in each chamber. Each fuel delivery unit drives a suction jet pump in the other chamber.Inside view of tank – petrol engineG Fuel gauge sender G6 Fuel system pressurisation pump and suction jet pumpG169 Fuel gauge sender 2 and suction jet pumpSuction jet pump 361_08142Exhaust system4.2l V8 FSI engineThe complete exhaust system from the cylinder heads to the tailpipes is designed as a dual-branch system. Air gap insulated manifolds in the clamp flange technique are bolted onto the cylinder heads. These optimize flow characteristics, ensuring quick heating of the catalytic converters. The metal oxidation catalytic converters reach operating temperature very quickly thanks to their design and proximity to the engine. The broadband and transition Lambda probes are located upstream and downstream of the primary catalytic converters respectively. The two ceramic catalytic converters are located near the underbody. The front silencer is a shared component. It is designed as an absorption-type silencer and features a "pressure equalizer" between the two exhaust branches, which has a positive impact on engine power output and torque. The absorption-type front silencer is also a shared component. However, it contains an internal partition for the exhaust branches.Air-gap insulated manifold in clamp flange technique Ceramic primary catalytic converter Decoupling element Ceramic main catalytic converterAbsorption rear silencer with inner partitionAbsorption front silencer with "pressure equalizer" 361_1243.0l V6 TDI engineWith this engine, the exhaust system downstream of the turbocharger is designed as a singe-branch system. Cast manifolds are bolted to the cylinder heads, which route the exhaust gas into the common turbocharger. A metal catalytic converter is fitted downstream of the turbocharger. The maintenance-free diesel particulate filter is located in the underbody area. The rear silencer is designed as a reflection silencer.Metal catalytic converterDiesel particulate filter Reflection silencer361_09543Running gearOverviewThe running gear also excels through its all-rounder qualities. Steel-spring suspension and twin tube shock absorbers are set up for sporty driving properties and high comfort, even during off-road use. The optionally available adaptive air suspension with an electronically controlled damper system represents the perfect synthesis of decidedly sporty handling characteristics and the highest ride comfort.362_001Front axleA double wishbone axle is used. The design principle has been adopted from the VW Touareg. The springs, shock absorbers, anti-roll bars and lower wishbones have been modified.361_12844Rear axleA double wishbone axle with split upper wishbones is used. The design principle has been adopted from the VW Touareg. The mounting bracket, wheel bearings and wishbones are identical components. The increased track width, which has been extended by 14 mm, is achieved by means of a modified wheel carrier.362_075Brake systemFront axle Engine Minimum wheel size Brake type Number of brake pistons Brake piston diameter (mm) Brake disc diameter (mm) V8 petrol engine, V6 FSI and TDI 18" Brembo aluminium fixed caliper 6 30/34/38 350 V8 petrol engine 18"Rear axle V6 FSI and TDI 18" Brembo aluminium fixed caliper 4 28/30 330Brembo aluminium fixed caliper 4 28/32 358Internally ventilated brake discs are used on the front and rear axles. The brake pads feature brake pad wear monitoring. The parking brake is a foot-operated servo drum brake.362_036362_03745Running gearBrake systemAn active brake servo is used for the first time. Through electrical activation of a proportional magnet in the brake servo, brake pressure can be generated without actuation of the pedal by the driver. An admission pressure is generated on the suction side of the ESP pump. This enables the ESP pump to generate braking pressure very rapidly. The rapid brake pressure generation is required for certain ESP control interventions.Solenoid362_045ESPOwing to the large brake fluid volume in the brake system of the Audi Q7, a new TEVES ESP assembly with the designation Mk25E1 is used. Active Hall sensors are used to detect the wheel speeds. The operating principle is the same as that of the sensors already used in the Audi A8 ´03. In the Audi Q7, the familiar dual sensor is used for detecting lateral acceleration, yaw velocity and longitudinal acceleration. The sensor is installed in the front passenger footwell.362_052362_08046ESPESP on-road control Optimum stabilityControl is speed dependentESP off-road control Optimum tractionRoad speed (km/h)362_057Some new functions are implemented with the new ESP. The "off-road" mode is particularly worthy of mention. The basic function of this mode is to optimise the ESP/ASR/EDS and ABS interventions with respect to traction and braking on loose surfaces (off-road).362_058The mode is activated by briefly pressing ( 3 s) on the ESP button.362_05947Running gearSteering systemA conventional hydraulic steering system with a vane pump, rotary slide valve and a rack-and-pinion steering gear with a variable ratio is used. The Servotronic function is equipped as standard. The Servotronic II familiar from the current Audi A8 ´03 is used (see SSP 285). Activation of the Servotronic solenoid valve is performed by the onboard supply control unit J520.The design and function of the steering wheels have been adopted from the Audi A6 ´05. The range comprises three-spoke and four-spoke steering wheels. These are optionally available with leather trim, multifunction buttons, Tiptronic and heated steering wheel rim.362_064362_069A mechanically-adjustable steering column is available as basic equipment. The plate-clamp system is the same as on the steering columns of the Audi 8 and Audi A6 ´05 (see SSP 285). The steering columns for the Audi Q7 are also equipped with an electric steering column lock.362_034An electric steering column is available as optional equipment. The electric drives have been adopted from the steering column of the Audi A8 ´03.48Wheels and tyresEngineBasic wheels 7.5J x 18 ET 53 (1) Forged light-alloy wheel, varnished 235/60 R 18Optional wheels, 18" 8J x 18 ET 56 (3) Forged light-alloy wheel, polished 255/55 R 18 8.5J x 18 ET 58 (4) Forged light-alloy wheel, varnished 255/55 R 18Optional wheels, 19" 8.5J x 19 ET 62 (5) Forged light-alloy wheel, varnished 265/50 R 19Optional wheels, 20" 9J x 20 ET 60 (6) Forged light-alloy wheel, polished, two-colour 275/45 R 20Winter wheels 7.5J x 18 ET 53 (1) Forged light-alloy wheel, varnished 235/60 R 186-cylinder8-cylinder8J x 18 ET 56 (2) Forged light-alloy wheel, varnished 255/55 R 18(available as optional equipment for 6cylinder)362_035Tyre pressure monitoring systemA tyre pressure monitoring system is optionally available for the Audi Q7. Its design and operating principle are the same as those of the Audi A6 ´05 (see SSP 324).361_12749Electrical systemInstallation overview of control unitsNote For more information on the electrical system, please refer to the self-study programme SSP 364 Audi Q7 – Electrics.364_004Key 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 Garage door operation control unit J530 Adaptive cruise control unit J492 Data bus diagnostic interface J533 Onboard supply control unit J519 Control unit for headlight range J431 Tyre pressure monitor control unit J502 Entry and start authorisation control unit J518 Steering column electronics control unit J527 Driver door control unit J386 Rear left door control unit J388 Front passenger door control unit J387 Rear right door control unit J389 Energy management control unit J644 Airbag control unit J234 Onboard supply control unit 2 J520 Front passenger seat adjustment with memory control unit J521 Battery A50364_005Key 20 21 22 23 24 25 26 27 28 29 30 31 32 33 Rear lid control unit J605 Rear lid control unit 2 - J756 Reversing camera system control unit J772 Convenience system central control unit J773 Convenience system central control unit J393 Auxiliary heater control unit J364 Aerial reader unit for keyless entry system J723 Parking aid control unit J446 Trailer detector control unit J345 Adaptive suspension control unit J197 Side assist control unit J769 Side assist control unit 2 - J770 Reversing camera R189 Radio controlled clock receiver J489Note For information on the driver assistance systems, please refer to the self-study programme SSP 375Audi Q7 - New Driver Assistance Systems.51Electrical systemNetworkingSide assist control unit 2 J770Control unit in dash panel insert J285Side assist control unit J769Adaptive cruise control J428Engine control unit J623Data bus diagnostic interface J533 Parking aid J446Engine control unit 2 J624Driver door control unit J386Energy management J644Yaw rate sender G202ABS J104Front passenger door control unit J387Additional heater J364Seat occupied sensor J706Airbag J234Rear left door control unit J388Tailgate J605Automatic gearbox J217 Power output module for left headlight J667 Power output module for right headlight J668Rear right door control unit J389 Seat adjustment and steering column adjustment with memory J136 Front passenger seat adjustment with memory J521Onboard supply control unit 2 J520Headlight range control J431Entry and start authorisation J518Self-levelling suspension J197Onboard supply control unit J519Convenience system central control unit 2 J773Convenience system central control unit J393Steering angle sender G85 Steering column electronics J527Trailer detection J345Tyre pressure monitor J502Climatronic J255Multifunction steering wheel J453Reversing camera system J772Rear Climatronic operating and display unit E26552Mobile phone operating electronics J412 Front information display and operating unit J523 Telephone transmitter and receiver unit R36 Telephone handset R37Navigation system with CD drive J401TV tuner R78Radio RLanguage input J507 Media player in position 1 R118 Digital sound packet J525MOST busDigital radio R147Dash panel insert CAN Diagnostics CAN Drive CANRear lid control unit 2 J756Wiper motor J400Rain and light sensor G397Convenience CAN Adaptive cruise control CANSliding sun roof J245Roof blind J394Rear sliding sunroof J392LIN bus Various secondary bus systemsEntry and start authorisation switch E415Aerial reader unit for keyless entry system J723Interior monitor G273Alarm horn H12Transmitter unit, front left G431Transmitter unit, front right G432Transmitter unit, rear left G433Transmitter unit, rear right G434Rear tyre pressure monitor aerial R96364_00653Air conditioning systemOverviewThe new Audi Q7 is equipped with an air conditioning system as standard. Three different air conditioners are available:Air conditioner (basic)Deluxe automatic air conditionerFour-zone deluxe automatic air conditioner361_069361_071361_118The systems can be identified by means of the different air conditioner operating units. The basic air conditioner does not feature an automatic function. The deluxe automatic air conditioner and the four-zone deluxe automatic air conditioner are equipped with sun-position dependent control, separate temperature and air distribution for the driver and front passenger sides, and indirect ventilation. Air conditioning of the rear passenger compartment is achieved via air vents in the Bpillars, and also in the C-pillars in the case of the four-zone system. The refrigerant circuit is a further development based on the air conditioning system already successfully implemented in the VW Touareg.Note The electrics and operation of the air conditioning system are based on the Audi A6 '05. The Climatronic control units J255 are also based on the Audi A6 '05 and have been further developed for use in the Audi Q7.The optionally available four-zone deluxe automatic air conditioner features an additional air conditioner unit in the rear passenger compartment. The components of the rear air conditioner unit are easily accessible behind the left side trim in the luggage compartment. The rear air conditioner unit has been adopted without modifications from the VW Touareg.Note The refrigerant circuit is described in detail in the self-study programme SSP 301.54Refrigerant circuitGeneralThe refrigerant circuits of the three systems are identical to those in the VW Touareg. The air conditioner units are supplied by a common compressor. In four-zone systems, the rear air conditioner unit additionally features a heat exchanger and an evaporator. The systems are equipped with a dust and pollen filter in the front air conditioner unit. The rear air conditioner unit only draws in already filtered interior air. The familiar R134a refrigerant is used. The refrigerant and refrigerant oil capacities are different for two and four-zone systems.Refrigerant circuit of both the two-zone systemsIn terms of design and function, the systems are the same as those familiar from the VW Touareg. Depending on the engine version, the refrigerant temperature sender G454 is installed. It is not used on all engine versions. The sender detects the temperature of the refrigerant and transmits it to the Climatronic control unit J255.Refrigerant temperature sender G454 Condenser with dryer cartridgeCompressorService connectionService connectionBlower in front air conditioner unitLow pressure High pressure Fresh air * depending on engine Expansion valveEvaporator 361_116 Evaporator temperature sensor G30855Air conditioningRefrigerant circuit of the four-zone deluxe automatic air conditionerThe two evaporators of the four-zone air conditioner are integrated in parallel into the refrigerant circuit. They are both supplied by a single externally-controlled compressor. In the case of a V6 TDI engine, the compressor is driven via a muli-V belt and in the case of a V8 FSI engine, via a drive shaft. The receiver is integrated in the condenser and contains the dryer cartridge. Currently, this can be replaced without removing the condenser when the refrigerant circuit is empty. The receiver is installed on the right side of the condenser.Refrigerant temperature sender G454 Dryer cartridge CompressorHigh-pressure sender G65 Service connection Service connectionExpansion valve The design and characteristic curve of the front expansion valve differ from those of the rear one.Expansion valve 1Evaporator in front air conditioner unit Blower in front air conditioner unit Evaporator temperature sensor G308Low pressure High pressure Fresh air Recirculated air from the passenger compartment * depending on engine 56 Expansion valve 2Evaporator in rear air conditioner unit 361_117Front air conditioner unitThe front air conditioner unit is the same in design and function as that of the VW Touareg. However, additional control motors have been fitted. All three air conditioners are air-controlled systems.Control motors on support platesDust and pollen filter361_084 Heat exchanger EvaporatorMost of the control motors can be replaced with the dash panel in place; the specific repair operations are described in the Workshop Manual.Air distribution in the front passenger compartmentFresh air is drawn in via the blower on the right side of the vehicle in the area of the plenum chamber. The air passes through the dust and pollen filter and the evaporator, which is located immediately adjacent to the pollen filter. In order to achieve independently-controllable air outlet temperatures for the driver and front passenger sides, separately adjustable temperature flaps are used in the deluxe automatic air conditioner and four-zone deluxe automatic air conditioner. The position of the temperature flaps determine the volume ratio at which cold evaporator air and heated air from the heat exchanger are mixed. This enables different air outlet temperatures to be set for the front occupants. In the case of the basic air conditioner, both temperature flaps are permanently attached to one another by means of a shaft. The air outlet temperature at the front vents is the same on both the driver and front passenger sides.57Air conditioningThe table shows the number and designations of the various control motors for the three air conditioner versions. In the basic air conditioner version, the control motors perform various functions:Automatic air conditioners Control motors No. Air conditioner (basic) 2-zone and 4-zone automatic air conditioners Front X 4-zone automatic air conditioner Rear1Left footwell flapV108XX Controls the L and R footwell flaps X Controls the L and R temperature flaps, is installed on right of air conditioner unit X X Controls the L and R side vents and the flaps of the L and R centre vents2Temperature flap, leftV158XX3 4Defrost flap Side vent, leftV107 V299X5 6 7 8 9 10 11 12 13 14 15 16 17 18Centre vent, left Centre vent, right Side vent, right Temperature flap, right Footwell flap, right Recirculated air flap Temperature flap, rear right Air flow flap, rear right Air flow flap, rear right Temperature flap, rear left Shutoff flap at B-pillar and footwell, left Directional vent, rear left Directional vent, rear right Shutoff flap at B-pillar and footwell, rightV110X XV300 V159 V109 V113 V314 V240 V239 V313 V212 V315 V316 V211 X Base without potentiometerX X X X X X X X X X X XA potentiometer is installed in each control motor. The air recirculation flap control motor V113 is an exception. The potentiometer for air recirculation flap control motor G143 is only installed in the control motor V113 in the case of the two deluxe automatic air conditioners. Consequently, in vehicles equipped with a basic air conditioner, the control motor V113 can only be moved from one end stop to the other. Fault detection is not possible without the potentiometer.58Rear air conditioner unitThe rear air conditioner unit is located under the side trim at the left of the luggage compartment. The blower motor draws in the air to be cooled directly from the passenger compartment. During auxiliary heater and residual heat operation, the rear air conditioner unit remains switched off.Blower motorRear heat exchanger361_070 Rear fresh air blower control unit J391 Evaporator Rear right temperature flap control motor V314Flaps of the rear air conditioner unitThe rear air conditioner unit has two temperature and two air flow flaps. These permit adjustment of the two separate climate zones for the rear occupants. The required outlet temperatures on the right or left rear passenger compartment sides are achieved through the mixture of cold air from the rear evaporator and warm air from the rear heat exchanger.Rear air conditioner unit service positionThe rear air conditioner unit can be brought into a service position. Both the refrigerant pipes and coolant hoses remain connected for this purpose, neither of the circuits are opened. In the service position, the rear heat exchanger and rear fresh air blower, for example, can be replaced.59Air conditioningOperating unitsAir conditioner operating unit (basic)With the basic air conditioner version it is possible to control the temperature, blower volume and air distribution via rotary controls. The system has no automatic recirculated air mode, no sun-position control and no indirect ventilation option. The heated front seats (optional equipment) can be adjusted in 3 stages, as in the Audi A6 '05.361_068Deluxe automatic air conditionerThe controls of the deluxe automatic air conditioner are the same as those in the Audi A6 ’05. The air conditioner control unit software has been adapted to the passenger compartment dimensions of the Audi Q7. Various automatic air conditioner settings can be saved. The saved data is assigned to the respective vehicle keys.The following data is saved: – Specified temperature, driver and front passenger sides – Air distribution, driver and front passenger sides – Heated seat settings for driver and front passenger sides – Air flow (blower volume)361_07160Four-zone automatic air conditionerThe rear Climatronic operating and display unit E265 beneath the rear vent in the centre console is the same as the one in the Audi A8 ´03. All the familiar functions are identical. In the Audi Q7, the rear air conditioner unit is used for the rear passenger compartment in the case of the four-zone automatic air conditioner.Self-diagnosisThe Climatronic control unit J255 and the rear Climatronic operating and display unit E265 are equipped with a fault memory. If faults occur in the monitored sensors and components, these are stored in the fault memory of the relevant control unit together with an indication of the type of fault. The fault memories are non-volatile memories and thus independent of the power supply.361_071Rear air conditioner operating unitThe two control units can be accessed via the addre