TECHNICAL DOCUMENTATION

SSP 365 Audi 4,2 l V8 TDI with Common Rail Injection System

PDFEN36 pages828 KB
SSP 365 Audi 4,2 l V8 TDI with Common Rail Injection System - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingAudi 4.2 l V8 TDI with Common Rail Injection System Self-Study Programme 365 In 1999, the 3.3 l A8 (1994) was installed for the first time with a V8 TDI engine, followed in the new A8 by an improved 4.0 l chain-driven engine. With the 4.2 l V8 TDI engine, the vee engine family with its 90° cylinder angle, 90 mm cylinder spacing and outputend chain drive has undergone a complete overhaul. The 4.2 l powerplant represents a logical evolution of the V8 TDI with 240 kW of power and 650 Nm of torque.365_001 Table of contents4.2 l V8 TDI engine with common rail injection systemDifferences between the 4.0 l and 4.2 l V8 TDI engines . . . . . . . . . . . . . . . . . . . . . 4Performance features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5Cranktrain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Cylinder head and valve gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Chain drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Oil circulation system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Crankcase breather system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14Cooling system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Air intake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Exhaust gas recirculation system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22System overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28CAN data bus interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Exhaust system with diesel particulate filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31Special tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32The Self-Study Programme contains information on the design and function of new models, new automotive components or new technologies. The self-study programme is not intended as a workshop manual! All values given are only intended to help explain the subject matter and relate to the software version applicable when the SSP was compiled. Use should always be made of the latest technical literature when performing maintenance and repair work.ReferenceNote 4.2 l V8 TDI engine with common rail injection systemDifferences between the 4.0 l and 4.2 l V8 TDI enginesSwitchable, exhaust gas recirculation cooler with water through-flowCommon rail injection system With third-generation piezoelectric injectorsExhaust gas recirculation system with electrical actuatorsCast exhaust manifold Adoption of cylinder head concept from the 3.0 l V6 TDICrankcase with 90 mm cylinder spacing and 83 mm cylinder boreBelt drive with torsion vibration damper, freewheel and additional stabilising roller365_001Optimised exhaust turbocharger4 Performance featuresEngine code, torque and power outputThe engine number is located on the end face of cylinder bank II, left.365_012Torque/power curve240750Max. torque in Nm Max. power output in kWkWNm1605501204508035040 1000 2000 3000 4000250 5000Engine speed in RPMSpecificationsEngine code Type of engine Displacement in cm3BVN V8 diesel engine 90° vee angle 4134 240 (326) 650 at 1600 to 3500 RPM 83 95.5 16,4 : 1 90 1–5–4–8–6–3–7–2 255 Bosch EDC-16CP+ common rail injection system up to 1600 bar with 8-port piezoelectric injectors Water-cooled EGR Two oxidising catalytic converters, Two maintenance-free diesel particulate filters EU IVMax. power output in kW (bhp) Max. torque in Nm Bore in mm Stroke in mm Compression ratio Cylinder spacing in mm Firing order Engine weight in kg Engine managementExhaust gas recirculation system Exhaust emission controlExhaust emission standard5 4.2 l V8 TDI engine with common rail injection systemCrankshaft driveThe crankcase with 90 mm cylinder spacing is made of vernicular graphite (GJV 450) and, like the 4.0 l V8 TDI engine, is split at the centre of the crankshaft and bolted to a sturdy crankshaft bearing frame. The weight of the engine block was reduced by approximately 10 kg by utilising the material's special properties. The forged steel crankshaft is made of 42 Cr Mo S4 and cranked in such a way that free first and second order moments are avoided. The crankshaft is runs in five bearings in the crankcase, and the radii of the con-rod bearing journals are rolled for strength reasons. By using a compact design it was possible to achieve torque-free balancing of the cranktrain using the crankshaft's counterweights alone. An optimum balance was achieved with the help of additional weights, which are attached to the vibration damper and the driver plate. The deep aluminium oil pan is to a great extent isolated from crankshaft drive vibration, which has a positive effect on acoustic quality. The main bearing frame contour serves an additional function. It acts as a "baffle plate" in the crankshaft counterweight and con-rod areas. Thus, draining oil is not distributed throughout the engine block, but is collected directly and drained off.CrankcaseMain oil portBearing frame CrankshaftAluminium oil panThese edges function as baffle plates 365_003 Oil return channels6 The UV laser imaging honing process used to manufacture the 3.0 l V6 TDI engine has also been used for this engine.This process helps to reduce oil consumption. The antifriction properties of the cylinder liners were significantly improved in this way.365_011a without laser imaging with laser imaging365_011bPistonDesigned as a recessed-head type piston, the piston has a higher recessed head with a larger diameter which reduces the engine's compression ratio from 17.3 : 1 to 16.4 : 1. The piston has an annular cooling duct to reduce the temperature of the piston ring zone and the recess rim. An oil spray nozzle continuously sprays the oil into the annular oil cooling duct in order to cool the piston crown.Comparison of piston crownsnewAnnular oil cooling duct365_016oldOil spray nozzle365_0257 4.2 l V8 TDI engine with common rail injection systemCrankshaft vibration damperThe 4.2 l V8 TDI engine is equipped with a torsion vibration damper (old version with a belt vibration damper with isolation of the poly vee belt track). To dampen oly vee belt vibrations, which occur at the different rates of acceleration of the piston during the combustion process, a freewheel was installed in the alternator and an additional stabilising roller was fitted. The torsion vibration damper was designed to reduce the torsional moments which occur in the medium engine speed range by approximately 13 % compared to a belt vibration damper. The result is less load on the crankshaft and improved engine acoustics. The new belt drive drives the alternator and the air conditioner compressor.Torsion vibration damperTorsional moment, amplitude in NmBelt vibration damper365_035Engine speed in rpmAdditional stabilising rollersCrankshaft counterweightFreewheel on the alternator 365_017Rubber track 8Belt track Cylinder head and valve gearDerived from the 3.0 l V6 TDI engine, the cylinder head is installed in combination with the following components: – – – – – four valves per cylinder, assembled camshafts, hydraulic valve lifters, roller cam followers and straight-cut/tensioned gears The camshafts are held in place in the cylinder head by a ladder frame with a flat sealing face. An acoustically isolated plastic cylinder head cover seals the cylinder head off from the exterior.Cylinder head coverLadder frameInjectors arranged in the centre of the combustion chamber365_004Rigid spur gearDesign The spur gear of the exhaust camshaft is split into two pieces in the cylinder head, left. The spur gear of the intake camshaft gear is split into two pieces in the cylinder head, right. The wider part of the spur gear (rigid spur gear) is attached securely to the camshaft. There are six ramps on the front side of the spur gear. The narrower part of the spur gear (moving spur gear) moves in radial and axial directions. Recesses for the six ramps are located on the back of the spur gear.Non-rigid spur gear365_023Six ramps9 4.2 l V8 TDI engine with common rail injection systemBreather duct in the cylinder headIf a leak occurs in the area of the copper injector ring seal, the air is able to escape from the combustion chamber through a duct due to the combustion pressure of 165 bar. The breather duct is located above the exhaust manifold in the cylinder head. It prevents the excess pressure from travelling from the combustion chamber via the crankcase breather to the compressor side of the exhaust turbocharger and possibly causing malfunctioning or damaging the ring seals.Piezoelectric injectorThe crankcase breather can be accessed through the oil chamber in the cylinder head Ring sealGlow plug channel365_022Ring seal to combustion chamberBreather duct365_03010 Chain driveThe chain drive adopted from the 4.0 l V8 TDI engine has been optimised with regard to friction and rotary oscillation. Part of the sliding rails in chain drive D has been replaced by a new chain tensioner, allowing the chain to be routed directly around the intermediate shaft, thus shortening the length of the chain. Chain drive B has also been optimised, whereby the number of teeth and the belt gear contact angle has been increased and the chain guide has been tapered. Ancillary units such as the oil pump, hydraulic pump and coolant pump are driven by chain drive D via a gear module.Chain drive B365_038Chain drive DChain drive C"New" chain drive BChain drive A Coolant pump"New" Chain drive DChain tensioner for chain drive D Oil pump 365_002Reference For further information, please refer to SSP 325 - Audi A6 ´05 Engines and Transmissions.11 4.2 l V8 TDI engine with common rail injection systemOil circulation systemThe oil circulation system, which is initially filled with 11.5 l oil, begins in the gear oil pump. The oil pressure relief valve is integrated in the oil pump. From here, the oil flows to the water-oil cooler installed in the engine's inner vee. The oil flows to the oil filter along internal ducts in the oil filter module. The oil filter module has a replaceable paper filter for ease of servicing. When the paper filter is removed, the oil remaining in the housing flows back into the oil pan through a drain valve. After leaving the oil cleaner, the pressurised oil is channelled into the main oil duct located in the inner vee of the engine block. Here, the lubrication points of the crankshaft, the crankshaft bearings and the oil spray nozzle are supplied with oil pressure. Both turbochargers are supplied with pressurised oil through additional outer oil lines from the main oilway. The oil pressure flows into the cylinder heads through risers with integrated restrictors, and from here to the camshafts, the cam followers and the hydraulic valve lifters. A special feature is the vacuum pump lubrication system, which is driven and supplied with oil by the intake camshaft in the cylinder head, right. The lubrication system is also supplied with pressurised oil via its own oilway from the main oil duct.Rear viewAdditional oil line from the oil gallery to the vacuum pump via the camshaft bearingOil filter module with integrated crankcase breatherWater-oil coolerOil return from the cylinder headsMain oil ductOil supply for turbochargerOil panTurbocharger return linePressurised oil course Oil return line Oil return pipe from the inner vee and the crankcase breather365_043Oil pump12 Oil pumpThe gear oil pump is driven by a hexagonal shaft connected to chain drive D via a gear module. The oil pressure relief valve which the re-routes the excess oil pressure (exceeding approx. 5.1 bar) to the suction side of the oil pump. An additional gear module on the oil pump drives the coolant pump and the oil pump.365_046 Water pump drive gear Drive gear from chain drive DOil pump drive gearCoolant pump drive shaft outputOil pump gearsOil intake from the oil pan via an oil intake pipeOverpressure regulator control valve pistonCompression spring365_045Oil pump cover, high pressure side365_047Pressure side to oil-water oil coolerIntake side of oil pan 13 4.2 l V8 TDI engine with common rail injection systemCrankcase breather systemAn oil filter module in the inner vee of the engine block accommodates the oil filter cartridge, the oilwater heat exchanger and the oil separator of the crankcase breather. The oil-water heat exchanger is designed in such a way that the maximum oil temperature remains well below the 150 °C max. limit even in extreme conditions. On the chain and belt sides of the engine, the incoming blow-by gases flow through the settling chamber in the inner vee to the three-cyclone oil mist separator. The blow-by gases flow through the settling chamber into the three-cyclone oil mist separator in which the existing fine oil particles are separated.Three-cyclone oil mist separator Pressure control valve for crankcase breatherAlmost all oil-free blow-by gases flow through the pressure control valve to the intake side of both turbochargers. The separated oil is channelled into an oilway in the crankcase and an oil drain pipe with integrated non-return valve below the oil level.To intake side of turbochargerIntake manifold outletSettling chamberOil return channel with engine-internal oil pipe365_03114 Cooling systemThe coolant pump and the thermostat are housed in a shared pump housing outside the engine. The water pump is driven the oil pump gear module which is attached to the chain drive D via two stub shafts. The pump housing has two outputs to the pressure side, each of which is routed to the outer side of the crankcase. On both sides of the crankcase are located press-fitted coolant distributor rails, each of which has four inlets from where the coolant flows into the water jackets between the cylinders. The crankcase coolant chamber is split in two longitudinally according to the cross-flow principle. As a result, the coolant flows upwards from the crankcase into the cylinder head, transversely through the cylinder head and back to the crankcase on the inside of the cylinder banks. A portion of the coolant flows directly from the pressure side to the intake side through small holes in the cylinder webs in order to ensure rapid heat dissipation from the cylinder. The coolant which is channelled through the engine collects in the inner vee of the crankcase, from where it flows to the cooler or back into the engine via the water pump depending on the thermostat setting.Return line from the engine to the coolant pumpto the coolerCrankcase, two-piece Inlet to engine Coolant distributor rail Right cylinder bankCoolant distributor rail Left cylinder bank Coolant pump from cooler Thermostat365_02715 4.2 l V8 TDI engine with common rail injection systemAir intakeThe design of the double-chambered air intake system, with two air filters, two air mass meters and two air-air charge-air intercoolers, was adopted from the 4.0 l V8 TDI engine. Air is drawn in through the two electrically adjustable throttle valves. A connection between the two cylinder banks in the charge air tube, the so-called pressure equaliser tube, provides an even air distribution and equalises the pressure between the cylinder banks and the exhaust-gas return line. The intake plenum, which is designed as a pressure equaliser tube, is subjected to higher temperatures due to the inflow of exhaust gases, and, therefore, is made of aluminium. The actual intake manifold is made of plastic and accommodates the intake manifold flaps. These flaps control the flow rate in the spiral duct and are used for adjusting the swirl depending on thermodynamic requirements. Each cylinder bank has a bidirectional electric motor which actuates the flaps by means of a linkage. Depending on operating state, there are open, closed and intermediate positions.Throttle valve positioner Right cylinder bankThrottle valve positioner Left cylinder bankfrom turbocharger Connecting duct as pressure equaliser tubefrom turbochargerCharge air tubeSwirl flapsInflow of the recirculated exhaust gases365_036Swirl flap adjuster16 Combustion processThe main factors influencing the combustion process in charged diesel engines are: – – – – – Combustion chamber shape Compression ratio Injection hydraulics Swirl formation Turbocharging To achieve these ambitious development goals, the combustion system with the new four-valve concept used successfully in the 3.0 l V6 TDI engine was taken as the basis and adapted for the eight cylinder. The duct geometry in combination with variably activated swirl flaps allows a broad propagation of the cylinder swirl. The switchable EGR cooling system significantly reduces untreated emissions, since hot or cooled exhaust gas can be added depending on the operating point and engine temperature.They are in mutual interaction with one another. The process was, therefore, optimised in iterative steps by utilising, in particular, the flexibility provided by the common rail system.Four-valve conceptPiezoelectric injectorCharging ductSwirl ductExhaust valvesExhaust port in the form of a Y-branch pipeIntake valvesRecessed-head type piston365_04117 4.2 l V8 TDI engine with common rail injection systemSwirl flapsSwirl flap open: The intake air can flow in large volumes through the open intake ports and into the combustion chamber, thereby ensuring optimal charging.365_015Variable swirl flap: To minimise untreated emissions, it is necessary to precisely adapt the cylinder swirl and hence the combustion process in dependence on the operating point. Requirement: continuous swirl flap adjustment.1200 rpm Particulate emissions (g/kWh)NOx emissions (g/kWh)365_034Swirl flap position NOx Particulates 365_018Swirl flap closed: The strong swirl effect at low engine load optimises the combustion process within the combustion chamber and therefore results in fewer emissions.365_01418 Exhaust gas recirculation systemThe exhaust gas flows from the exhaust manifolds through ducts cast into the cylinder heads to the EGR valves in the inner vee of the engine block. The exhaust gas is precooled via the auxiliary exhaustgas recirculation duct by the cylinder head water cooling system. The EGR valves were modified for electrical - rather than pneumatic - actuation, including position feedback, and protected against excessively high temperatures by means of a water cooling system. The precooled exhaust gases are subsequently cooled by a pneumatically operated exhaust gas recirculation cooler which enables cooling of the exhaust gases to be adapted depending on the operating point. After passing through the exhaust gas recirculation cooler, the exhaust gases flow up into a branching duct within the pressure equalizer tube and mix with the induced air flow directly downstream of the throttle valves. When designing the ducts and inlet points, special attention was paid to optimal mixing of the dual gas flows.365_037 Exhaust port from four-cylinder exhaust manifold through the cylinder head to the EGR valveExhaust-gas recirculation ducts in the pressure equalizer tubeEGR valve, left bankEGR valve, right bankTransverse duct in the cylinder head365_020Exhaust gas recirculation cooler with Bypass flap19 4.2 l V8 TDI engine with common rail injection systemExhaust manifoldThe short gas paths between the cylinder head and the turbocharger made it possible to change over from an air-gap insulated exhaust manifold to a pure cast manifold. This did not result in any additional heat loss for the oxidising catalytic converter. Due to the higher rigidity of the cast manifold (reduced oscillation), the design of the turbocharger support has been simplified, thus influencing positively the natural oscillation of the components.Exhaust gas tap for exhaust gas recirculationCoolant feed for turbochargerTurbocharger 365_006SupportOil return pipe, turbocharger20 TurbochargerTwo Garrett GT17 chargers of the latest generation with electrical actuators are used for charging. The compressor wheel and the guide vanes were optimised and the turbine-side fan was decoupled from the turbine in order to increase turbocharger speed (up to 226,000 rpm), exhaust gas temperature (approx. 860 °C) and charge pressure (approx. 2.5 bar absolute) in order to enhance engine performance. The turbine side is now sealed by a double ring seal instead of a single ring seal. This ensures a good level of gas tightness, even at temporarily elevated exhaust back pressures due to loaded particulate filters. The engine management system has dual air mass meters which ensure that both chargers run at the same speed, and therefore have the same delivery rate.Oil inlet Air guide vanesDecoupling of the fan and double ring sealCharge pressure control motorCoolant inletExhaust-gas temperature sensor365_01921 4.2 l V8 TDI engine with common rail injection systemFuel system200-1600 barmax. permissible pressure 1.8 bar from 0.8-1.8 bar Mechanical fuel pump 4.5-6.2 bar Fuel metering valve N290 (fuel metering unit fuel metering unit)High-pressure pump CP3.310 bar pressure retention valve Permeability in opposite direction at 0.3-0.5 bar for charging the injectors after repair work.Fuel temperature sender G81Temperature-dependent switchoverFuel filter with water separatorHigh-pressure 200-1600 barReturn pressure from injector 10 -11 barSupply pressure max. 1.8 bar Return pressure max. 1.8 bar22 Fuel pressure sender G247Rail element, cylinder bank II 5 6 7 8to injectors 5-8 N83, N84. N85, N86Rail element, cylinder bank I 1 2 3 4Fuel pressure control valve N27610-11 barInjectors 1-4 N30, N31, N32, N33Fuel cooler (air) on vehicle underbodyCheck valveFuel tank module with suction jet pump, non-return valve and prefilter fuel pump (pre-supply pump)Tank365_021 G6 G23 23 4.2 l V8 TDI engine with common rail injection systemHigh-pressure fuel circuitThe three-piston high-pressure pump is located in the inner vee of the engine, and is driven by the intake camshaft of cylinder bank II via a toothed belt. The high-pressure circuit consists of the following components: – High-pressure pump with fuel metering valve (fuel metering unit) N290. – Rail element I with fuel pressure regulating valve N276 and – Rail element II with rail pressure sensor G247 and 8-port piezoelectric injectors. It was possible to dispense with the distributor block in the CR system, as used in the 4.0 l V8 TDI engine. This fuel pressure regulator and the fuel pressure sensor were distributed along both rails. The rails themselves are now of welded construction, and no longer of forged construction. The rails are based on a seamlessly extruded steel tube, the open ends of which are sealed with threaded plugs. The connecting fittings for the high-pressure line and the rail pressure sensor were attached by capacitor discharge welding*. *Notes on capacitor discharge welding: The advantage of this method lies in the very limited heat affected zone around the weld seam. Thus, the basic structure of the raw material remains unaltered.Reference For further information on design and function, please refer to SSP 325 Audi A6 ´05 Engines and Transmissions.Fuel pressure sender G247 Fuel pressure regulating valve N276 Fuel metering valve N290 Rail IRail IIInjector365_032 24 Restrictors in the railWhen the injector closes and during subsequent injection cycles, a pressure wave forms at the injector outlet. This pressure wave propagates to the rail, wher it is reflected. To dampen the pressure waves, flow restrictors are integrated in the rail in the supply line, in the highpressure pump rail, in the left and right rails and upstream of each injector. These restrictors are produced by machining the outer surface of the rail. Note Make sure that the injector fuel line and the connecting line between the rails is tightened to the correct torque. Deformed or damaged high-pressure lines must not be reused, and must be replaced.High-pressure lineCap nutRestrictorRail365_04025 4.2 l V8 TDI engine with common rail injection systemFuel pressure regulating valve N276Reference A new fuel pressure regulating valve is used for the common rail system of the 4.2 l V8 TDI engine. When the valve is in a deenergised state, it ensures a "short circuit“ between the high-pressure end and the low-pressure end. Function: When the engine is running, the poppet valve is in force equilibrium with the spring and the magnetic circuit. The valve is open in the deenergised state whereby the spring relieves the load on the ball in the seat. Unlike the previous version (which had a short-time retention pressure of approx. 100 bar), the pressure in the rail is reduced immediately, thus preventing the fuel from draining into the cylinder if an injector is open. For further information on design and function, please refer to SSP 227 3.3 l V8 TDI Common Rail Injection System.Previous version365_033Note In the event of a faulty fuel pressure regulating valve, the complete rail must be replaced.Iron plateArmatureValve seat ball365_029Applied rail pressureCompression springDual-regulator conceptThe 3.0 l V6 TDI engine with common rail used a dual-regulator concept which activated the fuel pressure regulating valve N276 or the fuel metering valve (fuel metering unit) N290. With this concept, the pressure can be controlled simultaneously via the fuel pressure regulating valve and the fuel metering unit.Pressure regulating valve control at engine start and for fuel heatinInjection rateFuel metering unit control at high injection rates and high rail pressuresDual-regulator operation at idle, when coasting and at low injection rates Speed365_02826 Piezoelectric injectorsBy using piezoelectric injectors, it is possible to achieve: – multiple electrical activation periods per working cycle, – very short switching times for up to five injection cycles, – large forces counter to the current rail pressure, – high stroke precision for rapid rail pressure reduction Depending on the rail pressure, piezoelectric injectors require a drive voltage of between 110 and 148 V through capacitors in the control unit. Note When an injector is replaced, the adaptation value for the new injector must be written to the engine control unit. When the engine control unit is replaced, the injector rate matching values and the injector voltage matching valve must be transferred to the new engine control unit.Reference0-ring Connector overmouldingFor further information, please refer to SSP 325 - Audi A6 ´05 Engines and Transmissions.Electrical connection (blade terminal) Rod filterBodyReturn connection0-ring Actuator foot Actuator Actuator module Actuator sleeve Adjusting disc Actuator head Membrane Adjusting piece Low-pressure ring seal Coupler body Coupler piston Valve piston Tubular spring Valve piston spring Nozzle body Spring retainer Nozzle module Coupler moduleValve plate Valve pin Valve spring Restrictor plate Nozzle clamping nutSwitch valveInjector spring Sealing disc Adjusting disc Injector pintleNozzle ports modified from 7 to 8-port 365_03927 4.2 l V8 TDI engine with common rail injection systemSystem overviewSensorsAir mass meter G70Charge pressure sender G31 Intake air temperature sensor G42Engine speed sender G28Coolant temperature sender G62Oil temperature sender G8CAN-HighFuel temperature sender G81Fuel pressure sender G247 CAN-LowCoolant temperature sender at radiator outlet G83Altitude senderHall sender G40Engine control unit J623 (master)Accelerator pedal position sender G79 Accelerator pedal position sender -2- G185Exhaust gas pressure sensor 1 G450Exhaust gas temperature sender -1- G235 Engine control unit 2 J624 (slave)Lambda probe 1 G39Catalytic converter temperature sensor I G20Exhaust gas temperature sender 2 for bank 1 G448Auxiliary signals: P/N signal Term. 50 at starter Start relay, term. 50 stage 1/2 Request start Cruise control system Auxiliary water pump (relay to control)28Powertrain CAN data bus ActuatorsAutomatic glow period control unit 1 J179 Injectors for cylinders 1, 4, 6, 7 N30, N33, N84, N85Glow plugs for cylinders 1, 4, 6, 7 Q10, Q13, Q15, Q16Fuel pressure regulating valve N276Throttle valve module J338Intake manifold flap motor V157Exhaust gas recirculation actuator V338Fuel metering valve N290Exhaust gas recirculation cooler change-over valve N345 Fuel pump relay J17 and fuel pump G6 and G23Electro-hydraulic engine mounting solenoid valve, right N145 Engine component current supply relay J757Lambda probe heater Z19Auxiliary signals: Radiator fan control unit PWM 1/2 Engine speed Diagnostic connectionTurbocharger 1 control unit J724 Turbocharger 2 control unit J725Injectors for cylinders 2, 3, 5, 8 N31, N32, N83, N86 Exhaust gas temperature sender -1-, bank 2 G236 Air mass meter 2 G246 Glow time control unit 2 J703 Exhaust gas temperature sender 2 for bank 2 G449 Glow plugs for cylinders 2, 3, 5, 8 Q11, Q12, Q14. Q17Lambda probe 2 heater Z28Intake manifold flap motor 2 V275Catalytic converter check temperature sensor II G29Exhaust gas recirculation actuator 2 V339Lambda probe 2 G108Electro/hydraulic engine mounting solenoid valve, left N144Exhaust gas pressure sensor 2 G451 Throttle valve module 2 J544 365_042 29 4.2 l V8 TDI engine with common rail injection systemCAN data bus interfaces (powertrain CAN data bus)Engine control unit (master) J623Idling information (EBC) Kick-down information Clutch pedal switch Engine speed ACTUAL engine torque Coolant temperature Brake light switch information Brake pedal switch CCS switch positions CCS nominal speed NOMINAL/ACTUAL idling speed Preglow signal Throttle-valve angle Intake temperature OBD2 lamp "Hot" coolant warning lamp Fuel consumption Radiator fan activation Air conditioner compressor Power reduction Particulate filter lamp Start module Interlock switch Starter enable Starter de-mesh Load shedding Oil temperatureAutomatic gearbox control unit J217Selector mechanism activated/ deactivated Air conditioner compressor OFF Torque converter lock-up clutch state Target gear Selector lever position NOMINAL engine torque Motion resistance index (on downhill gradients) Limp-home program (information on self-diagnosis) OBD2 status Turbine speed Nominal idling speedData bus diagnostic interface J533 (gateway)ACC information Idle up Mileage Date Time Brake light Trailer detectorCAN HighCAN LowDiscrete lineCAN 2 LowCAN 2 HighEngine control unit 2 (slave) J624sends all information such as the master control unit via CAN 2 directly to the master control unit. The slave control unit also controls: - charge pressure for both turbochargers The signal from engine speed sender G28 is also transmitted via a discrete line.ABS control unit J104TCS request ABS request EDL request ESP intervention ESP brake light switch Road speed signal EBC intervention torque Lateral acceleration Wheel speedSteering angle sensor G85Steering wheel angle (is utilised for pre-control of idling speed and for calculating the engine torque based on the power demand of the power steering system)30 Exhaust system with diesel particulate filterA double-chambered exhaust system with particulate filter is used in combination the 4.2 l V8 TDI engine. Each channel of the exhaust system comprises a close-coupled oxidising catalytic converter and a catalysed soot diesel particulate filter located in the under-body area. To minimise heat loss, the pipes from the turbochargers to the diesel particulate filters are air-gap insulated. As in the 3.0 l V6 TDI engine, a diesel particulate filter consisting of a thin-wall silicon carbite substrate is used. Wall thickness has been reduced by 37 % to increase cellularity and thus enlarge the active surface area between the catalytic coating and the particulate layer. This helps to reduce the exhaust backpressure and ensure faster filter regeneration times. The combination of a thin-wall substrate and a catalytic coating allows controlled filter regeneration at temperatures between 580 and 600 °C in addition to low exhaust back-pressures. Reference For further information on filter regeneration, please refer to SSP 325 - Audi A6 ´05 Engines and transmissions.Pressure line tap upstream of diesel particulate filter Temperature sensor upstream of diesel particulate filterCatalysed soot diesel particulate filterPressure line tap downstream of diesel particulate filterLambda probes upstream of oxidising catalytic converter Oxidising catalytic converters365_009 Temperature sensors downstream of oxidising catalytic converterAir-gap insulated pipesDiesel particulate filter31 4.2 l V8 TDI engine with common rail injection systemSpecial toolsHere you can see the special tools for the 4.2 l V8 TDI engine with common rail.365_048T40069 Locating pinT40094 Camshaft insertion tool365_049365_050 T40062 Adaptor Sprocket wheel32 365_051T40049 Adaptor365_052T40060 Timing pins365_053T40061 Adaptor Camshaft33 Notes34 To broaden your knowledge of the common rail injection system, the following self-study programmes and CBTs have been prepared: Vorsprung durch Technik www.audi.co.ukAll rights reserved. Technical specifications subject to change without notice. Copyright AUDI AG N/VK-35 Service.training@audi.de Fax +49-7312/31-88488 AUDI AG D-74172 Neckarsulm Technical status: 10/05 Printed in Germany A05.5S00.18.20365