TECHNICAL DOCUMENTATION
SSP 390 The 7-speed Double-clutch Gearbox 0AM

This PDF is currently unavailable.
Read document text
Service TrainingSelf-study Programme 390The 7-speed Double-clutch Gearbox 0AMDesign and FunctionThe new 7-speed double-clutch gearbox from Volkswagen The 7-speed double-clutch gearbox 0AM is a further development of the very successful direct-shift gearbox 02E from Volkswagen. In terms of comfort and shifting without interrupting drive, it offers the same as the direct-shift gearbox 02E. It has been designed for engines with a torque of up to 250 Nm in the Polo, Golf, Passat and Touran. Whilst the direct-shift gearbox is on a par with vehicles with manual gearbox in terms of fuel consumption, the double-clutch gearbox has succeeded in reducing fuel consumption below that of manual gearboxes by means of certain technical innovations in the gearbox. This reduction in fuel consumption makes a significant contribution towards lowering emissions and safeguarding the environment. In this self-study programme, you can find out how the new double-clutch gearbox functions and which technical highlights have helped to reduce fuel consumption. We hope you enjoy reading it.S390_002Make use of the available range of training courses for training…S390_090NEWAttention NoteThe self-study programme shows the design and function of new developments. The contents will not be updated.For current testing, adjustment and repair instructions, refer to the relevant service literature.2ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Selector lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Design of the gearbox . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Mechatronic module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Electrohydraulic control unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34Oil circuit – hydraulic system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35Gearbox management system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Diagnosis . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Test yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 703IntroductionWith the new double-clutch gearbox 0AM, Volkswagen is presenting two world premieres:● ●The first 7-speed gearbox for mounting transversely at the front and The first double-clutch gearbox with dry double clutchMechatronic unitS390_060 Double clutchAs a design feature, the dry double clutch has an extensive impact on the entire gearbox concept. In comparison with the direct-shift gearbox 02E, efficiency has once again been considerably improved thanks to the new gearbox concept. This improved efficiency makes a significant contribution towards lowering consumption and emissions. The 7-speed double-clutch gearbox 0AM is a further milestone in the Volkswagen Group's gearbox strategy, and therefore extends Volkswagen's technological advantage still further.4Design features●● ● ● ● ●Modular design of the gearbox: The clutch, mechatronic unit and gearbox each form one unit Dry double clutch Separate oil circuit, mechatronic unit and mechanical gearbox, with lifetime fillings 7 gears on 4 shafts Oil pump driven subject to requirements No oil/water heat exchangerMechatronic unitDouble clutchS390_003Technical dataDesignation Weight Torque Gears Spread Operating mode Gearbox oil volume Mechatronic unit oil volume 0AM Approx. 70 kg including clutch 250 Nm 7 forwards gears, 1 reverse gear 8.1 Automatic and Tiptronic modes 1.7l - G 052 171 1.0l central hydraulic/power steering box oil G 004 0005Selector leverActuationThe selector lever is actuated as in vehicles with automatic gearboxes. The double-clutch gearbox also offers the option of shifting using Tiptronic. Precisely as in vehicles with automatic gearboxes, the selector lever is equipped with a selector lever lock and an ignition key withdrawal lock. The lock functions as before. The design is new. The selector lever positions are: P - Park To move the selector lever from this position, the ignition must be "on" and the foot brake must be depressed. The release button on the selector lever must also be pressed. R - Reverse gear The release button must be pressed to engage this gear. N - Neutral position In this position, the gearbox is in neutral. If the selector lever is set to this position for a long time, the foot brake must be depressed again to move it from this position. D - Drive position (Normal programme) In this drive position, the forwards gears are shifted automatically. S - Sport Automatic gear selection is carried out according to a "sporty" characteristic curve, which is stored in the control unit. + and – The Tiptronic functions can be carried out in the righthand selector lever gate and at the steering wheel switches.S390_006 Release buttonS390_005Tiptronic switch in steering wheel E3896Design of the selector leverSelector lever E313Hall senders in the selector lever mounting register the position of the selector lever and make it available to the mechatronic unit via the CAN bus.Selector lever locked in position P switch F319If the selector lever is in the "P" position, the switch transmits the signal – selector lever in "P" position – to the steering column electronics control unit J527. The control unit requires this signal to control the ignition key withdrawal lock.Selector lever lock solenoid N110The solenoid locks the selector lever in the "P" and "N" positions. The solenoid is controlled by the selector lever sensors control unit J587.Locking pin latch "P"Selector lever E313F319 Locking pin latch "N"N110S390_007Hall senders for detecting the selector lever position7Selector leverSelector lever lock solenoid N110How it works: Selector lever locked in "P" position If the selector lever is set to "P", the locking pin is located in locking pin latch "P". This prevents the locking lever from being moved unintentionally.Compression spring Selector lever lock solenoid N110Locking pin latch for "P"Locking pin S390_008Selector lever released: After switching on the ignition and actuating the foot brake, the selector lever sensors control unit J587 supply the selector lever lock solenoid N110 with current. As a result of this, the locking pin is withdrawn from the locking pin latch "P". The selector lever can now be moved to the drive position.S390_009Selector lever locked in "N" position If the selector lever is set to the "N" position for longer than 2 sec., the control unit supplies the solenoid with current. As a result of this, the locking pin is pressed into locking pin latch "N". The selector lever can no longer be unintentionally moved into a gear. The locking pin is released when the brake is actuated.Locking pin latch for "N"S390_ 0108Emergency release If the voltage supply to the selector lever lock solenoid N110 fails, the selector lever can no longer be moved, because selector lever lock "P" remains activated in the event of a power failure. By mechanically "pressing in" the locking pin with a narrow object, the lock can be released and the selector lever can be "emergency released" to the "N" position. The vehicle can be moved again.S390_0119Selector leverIgnition key withdrawal lockThe ignition key withdrawal lock prevents the ignition key from being turned back to the removal position if the parking lock is not engaged. It functions electromechanically and is controlled by the steering column electronics control unit J527. The steering column electronics control unit J527 detects the open switch. The ignition key withdrawal lock solenoid N376 is not supplied with current. The compression spring in the solenoid pushes the locking pin into the release position.Ignition key withdrawal lock solenoid N376S390_012How it works: Selector lever in "park position", the ignition is switched off. If the selector lever is set to the park position, the selector lever locked in position "P" switch F319 is opened.Retaining lugCompression springLocking pin S390_013 "Ignition off"10How it works: Selector lever in "drive position", the ignition is switched on. If the selector lever is set to the drive position, the selector lever locked in position "P" switch F319 is closed. The steering column electronics control unit then supplies the ignition key withdrawal lock solenoid N376 with current. The locking pin is pushed, overcoming the force of the compression spring, into the locked position by the solenoid. In the locked position, the locking pin prevents the ignition key from being turned back and withdrawn. Only when the selector lever is pushed into the park position does the selector lever locked in position "P" switch open, and the control unit swtches off the current supply to the solenoid. The locking pin is then pressed back by the compression spring. The ignition key can be turned further and can be removed.N376S390_014 "Ignition on"11Design of the gearboxBasic principleIn principle, the double-clutch gearbox consists of two independent, gear train halves. In terms of function, each gear train half is designed as a manual gearbox. A clutch is assigned to each gear train half. The two clutches are dry clutches. They are opened and closed and controlled by the mechatronic unit depending on the gear which is to be shifted. Gears 1, 3, 5 and 7 are shifted via clutch K1 and therefore via gear train half 1 and output shaft 1. Gears 2, 4, 6 and reverse gear are conducted via clutch K2 and therefore gear train half 2 and output shafts 2 and 3. One gear train half is always positively connected. The next gear can already be shifted in the other gear train half, because the clutch for this gear is still open. A conventional, manual gearbox synchroniser and shift unit is assigned to each gear.Principle diagram Output shaft 2 Output shaft 3 Gear train half 2Drive shaft 2 R 6 4 2 K2 K1Engine torque 7 5 3 1 Drive shaft 1Output shaft 1Gear train half 1 S390_01512Torque inputThe torque is transferred from the dual-mass flywheel, which is secured to the crankshaft, to the double clutch. To achieve this, the dual-mass flywheel is equipped with inner teeth. These engage in the outer teeth on the double clutch carrier ring. From there, the torque is transmitted onwards into the double clutch.Carrier ring Drive shafts 1 and 2 Outer teethInner teethS390_064Double clutchDual-mass flywheel13Design of the gearboxDouble clutch and torque curveThe double clutch is located in the bell housing. It consists of two conventional clutches, which are comprised to form a double clutch. During the remainder of this self-study programme, the clutches are referred to as K1 and K2. Clutch K1 transfers the torque to drive shaft 1 via splines. From drive shaft 1, the torque for gears 1 and 3 is transferred to output shaft 1 and that for gears 5 and 7 to output shaft 2. Clutch K2 transfers the torque to drive shaft 2 via splines. It transfers the torque for gears 2 and 4 to output shaft 1 and the torque for 6th gear and reverse gear to output shaft 2. Via reverse gear intermediate gear R1, the torque is then passed on to reverse gear R2 on output shaft 3. All three output shafts are connected to the differential final drive gear.Output shaft 3Clutch K2Dual-mass flywheelOutput shaft 2Clutch K1Drive shaft 1 For reasons of clarity, the gearbox is shown elongated.Drive shaft 2Output shaft 11 … 7 = 1st to 7th gears R1 = reverse gear intermediate gear R2 = reverse gear Final drive gear Differential S390_01614Double clutch drive plateFrom the carrier ring, the torque is transferred to the drive plate in the double clutch. To achieve this, the carrier ring and drive plate are joined firmly together. The drive plate is mounted on drive shaft 2 as an idler gear.How it works: If one of the two clutches is actuated, the torque is transferred from the drive plate onto the relevant clutch plate and onwards onto the corresponding drive shaft.Carrier ringDrive plate S390_065Drive shafts 1 and 2Dual-mass flywheelClutch K2 S390_067 Clutch K115Design of the gearboxThe clutchesTwo independent, dry clutches operate in the double clutch. They each conduct the torque into one gear train half. Two clutch positions are possible:● ●When the engine is switched off and idling, both clutches are open. During vehicle operation, only one of the two clutches is ever closed.Clutch K1Clutch K1 conducts the torque for gears 1, 3, 5 and 7 to drive shaft 1.Clutch K1 not actuatedDrive shaft 1S390_01716How it works: Clutch K1 To actuate the clutch, the engaging lever presses the engagement bearing onto the diaphragm spring. At several relay points, this compression movement is transformed into a tension movement. As a result of this, the pressure plate is pulled onto the clutch plate and the drive plate. The torque is therefore transferred onto the drive shaft. The engaging lever is actuated via valve 3 in gear train half 1 N435 by the hydraulic clutch actuator for K1.Clutch K1 actuatedPressure plateDiaphragm springEngagement bearingS390_066Drive plate Diaphragm spring Clutch plateS390_087 Engaging lever17Design of the gearboxClutch K2Clutch K2 conducts the torque for gears 2, 4, 6 and R to drive shaft 2.Drive shaft 2S390_01818How it works: Clutch K2 If the engaging lever is actuated, the engagement bearing presses against the pressure plate's diaphragm spring. As the diaphragm spring is supported by the clutch housing, the pressure plate is pressed against the drive plate and the torque is transferred onto drive shaft 2. The engaging lever is actuated via valve 3 in gear train half 2 N439 by the hydraulic clutch actuator for K2.Clutch K2 actuated Pressure plate Support point Drive plateDiaphragm springClutch plateEngagement bearingEngaging leverS390_08819Design of the gearboxDrive shaftsThe drive shafts are located in the gearbox housing. Each drive shaft is connected to a clutch via splines. These transfer the engine torque onto the output shafts according to the gear which is engaged. Drive shaft 2 is hollow. Drive shaft 1 runs through hollow drive shaft 2. A ball bearing, which is used to mount the drive shafts in the gearbox housing, is located on each shaft.S390_046Drive shaft 2 Drive shaft 1S390_019SplineBall bearing20Drive shaft 2Due to its installation position, drive shaft 2 will be described before drive shaft 1.Gear for G612 BearingS390_020 4th/6th gears 2nd/R gearsDrive shaft 2 is designed as a hollow shaft. It is connected to K2 via splines. Drive shaft 2 is used to shift gears 2, 4, 6 and R. To record the gearbox input speed, this shaft has the gear for gearbox input speed sender 2 G612.Drive shaft 1Bearing Impulse wheel for G632S390_0211st gear5th gear3rd gear7th gearDrive shaft 1 is connected to clutch K1 via splines. It is used to shift gears 1,3,5 and 7. To record the gearbox input speed, this shaft has the impulse wheel for gearbox input speed sender 1 G632.Please note that a strong magnet may destroy the impulse wheel for drive shaft 1. Further information on the impulse wheel can be found in self-study programme 308 "The Direct Shift Gearbox 02E".21Design of the gearboxOutput shaftsThree output shafts are contained in the gearbox housing. Depending on the gear which is engaged, the engine's torque is transferred from the drive shafts to the output shafts. An output gear, via which the torque is passed on to the differential final drive gear, is located on each output shaft.Installation position in the gearbox (View from the left – shown elongated)S390_023Output shaft 11st gear3rd gear4th gear2nd gearOutput gearS390_022 Bearing Sliding sleeve, gears 1/3 Sliding sleeve, gears 2/4 BearingThe following are located on output shaft 1: - The selector gears for gears 1, 2 and 3; the 3 gears are synchromeshed 3-fold. - The selector gear for 4th gear; the 4th gear is synchromeshed 2-fold.22Installation position in the gearbox (View from the left – shown elongated)S390_025Output shaft 25th gear7th gear6th gearR gear 1 R gear 2 Output gearS390_024Sliding sleeve, gears 5/7Sliding sleeve, gears 6/RThe following are located on output shaft 2: - The 2-fold synchromeshed selector gears for gears 5, 6 and 7, and - The intermediate gears R gear 1 and R gear 2 for reverse gear.23Design of the gearboxOutput shaft 3Installation position in the gearbox (View from the left – shown elongated)S390_027Parking lock gearGear wheel for R gearOutput gear Bearing BearingS390_026Sliding sleeveThe following are located on output shaft 3: - The 1-fold synchromeshed selector gear for R gear - The parking lock gear24DifferentialInstallation position in the gearbox (View from the left – shown elongated)S390_029Final drive gearS390_028The differential transfers the torque onwards to the vehicle's wheels via the drive shafts.25Design of the gearboxParking lockA parking lock is integrated into the double-clutch gearbox to ensure that it is parked securely and to prevent unintentional rolling away when the handbrake is not applied. The locking pin is engaged purely mechanically via a Bowden cable between the selector lever and the parking lock lever on the gearbox. The Bowden cable is used exclusively to actuate the parking lock.Connection ball for parking lock Bowden cableLocking pin Holding-down device Return spring for locking pin Detent springActuation pin Pre-tensioning springS390_030Parking lock gear26FunctionParking lock not actuated, (selector lever position R, N, D, S) When the parking lock is not actuated, the cone of the actuation pin lies on the holding-down device and the locking pin. The parking lock is held in the non-actuated position by a locking device.Holding-down device Detent spring Locking pin S390_061Actuation pinParking lock actuated, locking pin not engaged (selector lever position P) By actuating the parking lock, the cone of the actuation pin is pressed against the holding-down device and the locking pin. As the holding-down device is stationary, the locking pin moves down. If it encounters a tooth on the parking lock gear, the pre-tensioning spring is tensioned. The actuation pin is held in this position by the locking device.Locking deviceS390_062Pre-tensioning spring, tensionedParking lock actuated, locking pin engaged (selector lever position P) (locking pin engaged) If the vehicle continues to move, the parking lock gear also rotates. As the actuation pin is pre-tensioned, it automatically pushes the locking pin into the next tooth space on the parking lock gear.S390_063Pre-tensioning spring, relaxes Tooth of locking pin engaged in parking lock gear Actuation pin in end position27Design of the gearboxGear synchronisationA balked synchromesh with locking pieces is used in the case of all gears to synchronise the different speeds when changing gears. Depending on the shifting load, the gears are synchronised one- to three-fold.Gear 1st to 3rd 4th 5th to 7th R Synchromesh Three-fold Two-fold One-fold One-fold Synchroniser ring material Brass with molybdenum coating Brass with molybdenum coating Brass with molybdenum coating Brass with molybdenum coatingThe figure shows the synchromesh design for 2nd, 4th and R gears.Selector forkFirmly connected (welded)Selector gear 2nd gearOuter ring (intermediate ring) Synchronising hub Synchroniser Sliding sleeve ring (outer) Synchroniser ring Locking pieces (outer) S390_081 Intermediate ring Clutch splines Selector gear 4th gearSynchroniser ring (inner)Synchroniser ring (inner)Sliding sleeveSelector gear R gear Locking pieces Synchroniser ring Synchronising hub S390_08228Power transmission in the gearsTorque is transmitted into the gearbox via either clutch K1 or K2. Each clutch drives a drive shaft. Drive shaft 1 is driven by clutch K1 and drive shaft 2 is driven by clutch K2. Power is transmitted to the differential via - output shaft 1 for gears 1, 2, 3, and 4, - output shaft 2 for gears 5, 6 and 7, and - output shaft 3 for reverse gear and the parking lock.S390_033 1st gear Clutch K1 Drive shaft 1 Output shaft 1 Differential R gear Clutch K2 Drive shaft 2 Output shaft 3 DifferentialS390_034The change in rotational direction for reverse gear is carried out by output shaft 3.For greater clarity, power transmission is shown schematically in "elongated" form.29Design of the gearbox2nd gear Clutch K2 Drive shaft 2 Output shaft 1 DifferentialS390_0353rd gear Clutch K1 Drive shaft 1 Output shaft 1 DifferentialS390_0364th gear Clutch K2 Drive shaft 2 Output shaft 1 DifferentialS390_037305th gear Clutch K1 Drive shaft 1 Output shaft 2 DifferentialS390_0386th gear Clutch K2 Drive shaft 2 Output shaft 2 DifferentialS390_0397th gear Clutch K1 Drive shaft 1 Output shaft 2 DifferentialS390_04031Mechatronic moduleMechatronic unit for direct shift gearbox J743The mechatronic unit is the central gearbox control unit. Within it, the electronic control unit and the electrohydraulic control unit are combined to form one component. The mechatronic unit is flanged onto the gearbox, and is an autonomous u nit. It has a separate oil circuit, which is independent of the oil circuit for the mechanical gearbox.The advantages of this autonomous, compact unit are: - Apart from one sensor, all sensors and actuators are contained in the mechatronic unit. - The hydraulic fluid is specifically adapted to the requirements of the mechatronic unit. - Due to the separate oil circuit, no foreign material from the mechanical gearbox enters into the mechatronic unit. - Good low-temperature behaviour, as no compromise has to be made with the requirements of the gearbox in terms of viscosity behaviour.Mechatronic unit S390_04132The mechatronic unit's electronic control unit is the central gearbox control unit. All sensor signals and all signals from other control units come together here, and all actions are performed and monitored by it. 11 sensors are integrated into the electronic control unit; only the gearbox input speed sender G182 is located outside of the control unit. The electronic control unit hydraulically controls and regulates eight solenoid valves for shifting the 7 gears and for actuating the clutch. The electronic control unit learns (adapts) the positions of the clutches and the positions of the gear selectors when a gear is engaged and takes what has been learnt into consideration for further operation of these components.Location of sensors Temperature sender in control unit G510Gear selector movement sensor 4 G490 (gears 6/R) Gearbox input speed sender 2 G612 Vehicle connectorGear selector movement sensor 3 G489 (gears 5/7)Gearbox input speed sender 1 G632Gear selector movement sensor 1 G487 (gears 4/2)Electronic control unit with integrated sensor systemGearbox input speed sender G182Gear selector movement sensor 2 G488 (gears 1/3)S390_042Gearbox hydraulic pressure sender G270Clutch travel sender 1 G617 for K1 Clutch travel sender 2 G618 for K2 S390_08333Electrohydraulic control unitThe electrohydraulic control unitThe electrohydraulic control unit is integrated into the mechatronic module. It generates the oil pressure which is required to shift the gears and to actuate the clutches.Oil pressure generation and controlThe oil pressure is generated by the hydraulic pump's motor. An oil pressure accumulator ensures that sufficient oil pressure is always present at the solenoid valves.Oil pressure accumulator Electrohydraulic control unitTo clutch K1Hydraulic pumpTo clutch K2 Valve 2 in gear train half 2 N438 Gear selector valve 6/R Valve 3 in gear train half 1 N435 Clutch valve K1 Valve 2 in gear train half 1 N434 Gear selector valve 5/7 Gear selector valve Valve 4 in gear train half 1 N436 Gear train half Pressure regulator Valve 1 in gear train half 1 N433 Gear selector valve 1/3 Motor for hydraulic pump V401 Valve 4 in gear train half 2 N440 Gear train half Pressure regulator Valve 3 in gear train half 2 N439 Clutch valve K2 Valve 1 in gear train half 2 N437 Gear selector valve 2/4S390_04334Oil circuit – hydraulic systemOil circuitThe double-clutch gearbox operates with two independent oil circuits using two different oils: - Oil circuit for mechanical gearbox - Oil circuit for mechatronic module Each oil circuit contains an oil which is specifically suitable for to its requirements.Mechatronic module Oil circuit for mechanical gearboxS390_080Oil circuit - mechanical gearboxThe oil supply to the shafts and gears of the mechanical gearbox is carried out in the same way as for a normal manual gearbox. It will not therefore be dealt with in any greater detail here. The oil volume in the mechanical gearbox is 1.7 l.Oil circuit - mechatronic moduleThe oil supply for the mechatronic unit is separate from the oil circuit for the mechanical gearbox. An oil pump delivers the oil at the pressure required to enable the hydraulic mechatronic unit components to function. The oil volume in the mechatronic unit is 1.1 l.For the precise capacities, please refer to the current Workshop Manual, "The 7-speed Double-clutch Gearbox 0AM".35Oil circuit – hydraulic systemOil circuit flow chartBasic oil circuitFilter Motor for hydraulic pump V401 Pressure limiting valve Pressure accumulator Hydraulic pressure senderNon-return valve Hydraulic pumpS390_09836Hydraulic pumpThe hydraulic pump unit is located in the mechatronic module. It consists of a hydraulic pump and an electric motor. The motor for the hydraulic pump is a brushless DC motor. It is actuated by the mechatronic unit's electronic control unit depending on pressure requirements. It drives the hydraulic pump via a coupling.Hydraulic pumpS390_043 Motor for hydraulic pump V401Intake sideThe hydraulic pump operates according to the principle of a gear pump. It intakes the hydraulic oil and pumps it into the oil circuit at a pressure of approx. 70 bar. The hydraulic oil is pumped from the intake side to the pressure side between the walls of the pump housing and the tooth gaps.HousingS390_071 Pressure side Driving gear37Oil circuit – hydraulic systemMotor for hydraulic pump V401Design Like conventional, smaller DC electric motors, the brushless DC motor also consists of a stator and a rotor. Whilst the stator consists of permanent magnets and the rotor of electromagnets in the conventional, smaller electric motor, the opposite is true in the case of the brushless DC motor. The rotor consists of 6 permanent magnet pairs and the stator of 6 electromagnet pairs.Rotor with permanent magnets Torque to the hydraulic pumpElectrical connectionElectromagnet pole pairsHow it works In the conventional DC motor, commutation (current direction change-over) takes place via ring contacts. Commutation in the brushless DC motor is carried out by the mechatronic unit's electronic control unit and is therefore contact-free. The stator coils are actuated in such a way that a rotating magnetic field occurs in the stator coils. The rotor follows this magnetic field and is therefore caused to rotate. Thanks to contact-free commutation, the DC motor runs entirely wear-free, with the exception of bearing wear.S390_085StatorStator RotorS390_08938Electrical actuationSo that a rotational movement is carried out, the mechatronic unit control unit switches between the possible phases in the individual pole pairs within good time. The magnetic field changes. The rotor is therefore constantly compelled to turn itself and therefore carries out a rotational movement.The schematic shows the design of the circuit using the example of a wound coil.Mechatronic unit control unitSupply voltage2nd phase3rd phase1st phaseWound coilS390_086Legend 1st phase – positively switched 2nd phase – negatively switched 3rd phase - open39Oil circuit – hydraulic systemGearbox hydraulic pressure sender G270 and pressure limiting valveThe hydraulic pump pumps the hydraulic oil through the filter towards the pressure limiting valve, the pressure accumulator and the hydraulic pressure sender. When the hydraulic oil pressure at the pressure limiting valve and the hydraulic pressure sender reaches approx. 70 bar, the control unit switches the electric motor and therefore the hydraulic pump off. The bypass ensures that the system functions if the filter channel is clogged.Pressure limiting valveHydraulic pressure senderS390_100Pressure accumulatorPressure accumulatorThe pressure accumulator is designed as a gas pressure accumulator. It provides the hydraulic system with oil pressure when the hydraulic pump is switched off. Its storage volume is 0.2 litres.S390_09640Oil circuit flow chartWorking pressure Return Controlled working pressure KS = Clutch safety valveKSKSClutch actuator K1 Gear selector 1 - 3 Gear selector 5 - 7 Gear selector 4 - 2Clutch actuator K2 Gear selector 6 - R S390_048Legend N433 N434 N435 N436 Valve 1 in gear train half 1 Valve 2 in gear train half 1 Valve 3 in gear train half 1 Valve 4 in gear train half 1 N437 N438 N439 N440 Valve 1 in gear train half 2 Valve 2 in gear train half 2 Valve 3 in gear train half 2 Valve 4 in gear train half 2The clutch safety valves enable the clutches to be drained and therefore opened in the event of a fault.41Oil circuit – hydraulic systemTask and function of the solenoid valves in the oil circuitGear train half pressure control solenoid valves The gear train half pressure control solenoid valves control the oil pressure for gear train halves 1 and 2. If a fault is detected in a gear train half, the pressure control solenoid valve can shut off the corresponding gear train half.Gear train half 1 pressure control valve S390_101Gear train half 2 pressure control valveGear selector solenoid valves The gear selector solenoid valves control the volume of oil to the gear selectors. Each gear selector shifts 2 gears. If no gear is engaged, the gear selectors are held in the neutral position via oil pressure. In selector lever position "P" and when the ignition is switched off, 1st gear and reverse gear are engaged.Gears 6/R Gears 5/7 Gears 2/4 S390_102Gears 1/3Clutch actuator solenoid valves The clutch actuator solenoid valves control the volume of oil to the clutch actuators. The clutch actuators actuate clutches K1 and K2. When not supplied with current, the solenoid valves and the clutches are open.K1K2S390_10342Shifting the gearsAs in the case of conventional manual gearboxes, the gears are shifted using selector forks. Each selector fork shifts two gears. The selector forks are mounted on both sides in the gearbox housing.Selector fork gears 5/7 Selector fork gears 6/RSelector fork gears 1/3Selector fork gears 2/4S390_05843Oil circuit – hydraulic systemShifting the gearsWhen changing gears, the selector forks are moved via the gear selectors integrated into the mechatronic unit.Gear selector gears 5 and 7Gear selector gears 6 and RGear selectors and selector forksThe gear selector piston is connected to the selector fork. To change gears, oil pressure is applied to the gear selector piston, thereby moving it. When it moves, it also moves the selector fork and the sliding sleeve. The sliding sleeve actuates the synchronising hub and the gear is engaged.Gear selector gears 1 and 3 Gear selector gears 2 and 4 S390_107Gear selector movement sensor Gear selector cylinder Gear selector pistonPermanent magnetSliding sleeveSelector fork Synchronising hubS390_056Via the permanent magnet and the gear selector movement sensor, the mechatronic unit detects the new position of the selector fork.44Gear changesAs in the case of the direct shift gearbox 02E, the selector forks are actuated hydraulically. To change the gears, the mechatronic electronic control unit actuates the corresponding gear selector solenoid valve. How it works Changing to 1st gear is shown here as an example. Initial position The gear selector piston is held in neutral position "N" via the oil pressure controlled by gear selector solenoid valve N433 for gears 1 and 3. No gear is engaged. Valve 4 in gear train half 1 N436 controls the oil pressure in gear train half 1.Mechatronic unitN436 Pressure control valve in gear train half 1 N433 gears 1/3Gear selector cylinder Gear selector pistonPiston chamber Selector forkSliding sleeveS390_05745Oil circuit – hydraulic systemChanging to 1st gear To change to 1st gear, the gear selector valve increases the oil pressure in the left piston chamber. As a result of this, the gear selector piston is pushed to the right. As the selector fork and the sliding sleeve are connected to the gear selector piston, they also move to the right. Due to the sliding sleeve's movement, 1st gear is engaged.Mechatronic unitN433 gears 1/3 Gear selector cylinder Gear selector pistonPiston chamber Selector forkSliding sleeveS390_09746Clutch actuatorsClutches K1 and K2 are actuated hydraulically. To achieve this, the mechatronic unit contains a clutch actuator for each clutch. A clutch actuator consists of a clutch actuator cylinder and a clutch actuator piston. The clutch actuator piston actuates the clutch engaging lever. The clutch actuator piston is equipped with a permanent magnet, which is required by the clutch travel sender to detect the piston position. To prevent detection of the piston position from being impaired, the actuator cylinder and the actuator piston must not be magnetic.Clutch actuator K1 Clutch actuator cylinderPermanent magnet Boot Clutch actuator piston Piston rodDust protection bellowsEngaging lever Support ring Guide ring Clutch actuator K2 S390_09247Oil circuit – hydraulic systemClutch operationTo actuate the clutches, the mechatronic electronic control unit actuates the solenoid valve● ●How it works Actuation of K1 is shown here as an example.N435 valve 3 in gear train half 1 for clutch K1 and N439 valve 3 in gear train half 2 for clutch K2.Clutch not actuated The clutch actuator piston is in the resting position. The solenoid valve N435 is open in the return flow direction. The oil pressure from the gear train half pressure control valve N436 flows into the mechatronic unit's oil reservoir.N435Clutch actuator K1 in resting positionS390_09348Clutch actuated If clutch K1 is to be actuated, the solenoid valve N435 is actuated by the electronic control unit. When actuated, it opens the oil channel to the clutch actuator, and oil pressure is built up at the rear of the clutch actuator piston. The clutch actuator piston moves and thereby actuates the K1 clutch engaging lever. Clutch K1 is closed. The control unit receives a signal regarding the precise position of the clutch via clutch travel sender 1 G167. Clutch slip, the speed difference between the gearbox input speed and drive shaft speed, is achieved by solenoid valve N435 by controlling the oil pressure between the clutch actuator and the return flow.N435Clutch actuator K1 actuatedS390_09449Gearbox management systemOverview of the systemSensorsGearbox input speed sender G182 Mechatronic unit for direct shift gearbox J743Gearbox input speed sender 1 G632 Gearbox input speed sender 2 G612Clutch travel sender 1 G617 Clutch travel sender 2 G618Gear selector movement sensor 1 Gear selector movement sensor 2 Gear selector movement sensor 3 Gear selector movement sensor 4G487 G488 G489 G490Gearbox hydraulic pressure sender G270Temperature sender in control unit G510Tiptronic switch in steering wheel E389Diagnostic connector50CANSelector lever E313Dash panel insert J285ActuatorsMotor for hydraulic pump V401Valve 3 in gear train half 1 N435 Valve 3 in gear train half 2 N439Valve 4 in gear train half 1 N436 Valve 4 in gear train half 2 N440Valve 1 in gear train half 1 N433 Valve 2 in gear train half 1 N434 Valve 1 in gear train half 2 N437 Valve 2 in gear train half 2 N438S390_05351Gearbox management systemSensorsClutch travel sender 1 G617, clutch travel sender 2 G618The clutch travel senders are located in the mechatronic unit above the clutch actuators. The double clutch control system requires reliable and precise recording of the current clutch actuation status. For this reason, contact-free sensor technology is used to record clutch travel. Contact-free position recording increases the reliability of the sensor functions. Measured value falsification caused by wear and vibrations is avoided.G617/G618S390_050Signal use The control unit requires these signals to control the clutch actuators.Effects of signal failure If clutch travel sender 1 G617 fails, gearbox path 1 is shut off. Gears 1, 3, 5 and 7 can no longer be engaged. If clutch travel sender 2 G618 fails, gears 2, 4, 6 and R can no longer be engaged.52Clutch travel senderDesign A clutch travel sender consists of:●How it works An alternating voltage is applied to the primary coil. As a result of this, a magnetic field is built up around the iron core. If the clutch is actuated, the clutch actuator piston moves through the magnetic field with the permanent magnet. Due to the permenant magnet's movement, a voltage is induced in the secondary evaluation coils. The level of the voltage induced in the left and right evaluation coils is dependent on the position of the permanent magnet. Via the level of the voltage in the left and right evaluation coils, the sensor electronics detect the position of the permanent magnet and therefore the position of the clutch actuator piston.● ●●An iron core, around which the primary coil is wound Two secondary evaluation coils A permanent magnet, which is located on the clutch actuator piston, and The sensor electronicsPrimary coil Secondary evaluation coilIron coreApplied alternating voltagePermanent magnet S390_091 Clutch actuator piston Evaluation voltage Sensor electronics53Gearbox management systemGearbox input speed sender G182The gearbox input speed sender is inserted into the gearbox housing. It is the only sensor located outside of the mechatronic unit. It electronically scans the starter ring gear and thereby records the gearbox input speed. The gearbox input speed is identical to the engine speed. The sender operates according to the Hall principle.G182S390_073Signal use The control unit requires the gearbox input speed signal to control the clutches and to calculate slip. To do this, it compares the signals from the gearbox input speed sender G182 before the clutches with the signals from senders G612 and G632, which transmit speed signals from the drive shafts.Effects of signal failure In the event of signal failure, the control unit uses the engine speed signal as a substitute signal. It obtains this signal from the engine control unit via the CAN bus.54Gearbox input speed sender 1 G632 and gearbox input speed sender 2 G612Both senders are housed in the mechatronic unit.●Sender G632 scans an impulse wheel, which is located on drive shaft 1. From this signal, the control unit calculates the speed of drive shaft 1.●Sender G612 scans a gear on drive shaft 2. From this signal, the control unit calculates the speed of drive shaft 2.Both senders are Hall senders.G632G612S390_049Signal use The speed signals from drive shafts 1 and 2 are used by the control unit to control the clutch and to calculate clutch slip.Effects of signal failure If sender G632 fails, gear train half 1 is shut off. The vehicle can then only be driven in gears 2, 4, 6 and R. If sender G612 fails, gear train half 2 is shut off. The vehicle can then only be driven in gears 1, 3, 5 and 7.55Gearbox management systemTemperature sender in control unit G510The temperature sender is located directly in the mechatronic unit's electronic control unit. Hot hydraulic oil constantly flows around the control unit, thereby heating it. Severe heating may impair the functions of the electronics. The sender measures the temperature directly of the components at risk. As a result, measures to reduce the oil temperature can be introduced at an early stage, thereby avoiding excessive heating.G510S390_074Signal use The sender's signal is used to check the mechatronic unit's temperature. At a temperature of 139 °C, engine torque reduction can be implemented.Effects of signal failure In the event of signal failure, the control unit uses an internally available substitute value.56Gearbox hydraulic pressure sender G270The hydraulic pressure sender is integrated into the mechatronic unit's hydraulic oil circuit. It is designed as a diaphragm pressure sender. Further information on the hydraulic pressure sender can be found in self-study programme 308 "The Direct Shift Gearbox 02E".G270S390_075Signal use The control unit uses the signal to control the motor for the hydraulic pump V401. At a hydraulic oil pressure of approx. 60 bar, the motor is shut off according to the pressure sender signal, and is switched on again at approx. 40 bar.Effects of signal failure In the event that the signal fails, the motor for hydraulic pump runs continuously. The hydraulic pressure is determined by the pressure control valve.57Gearbox management systemGear selector movement sensors 1 to 4, G487 to G490The gear selector movement sensors are located in the mechatronic unit. On combination with the solenoids on the selector forks, they generate a signal, from which the control unit recognises the precise position of the gear selectors.G490 gears 6 and RG489 gears 5 and 7S390_051 G488 gears 1 and 3 G487 gears 2 and 4Signal use The control unit requires the precise position of the gear selectors to control the gear selectors for changing gears.Effects of signal failure If a movement sensor fails, the control unit cannot detect the position of the corresponding gear selector. As a result, the control unit is unable to recognise whether or not a gear is changed via the gear selector and the selector fork. To prevent damage to the gearbox, the gearbox path of the movement sensor which has failed is shut off in this case.58Selector lever E313The selector lever sensor system and the control system for the selector lever lock solenoid are integrated into the selector lever. The selector lever positions are detected by Hall sensors, which are integrated into the selector lever sensor system. The selector lever position signals and the Tiptronic signals are transmitted via the CAN bus to the mechatronic unit and to the control unit in the dash panel insert. Signal use Based on the signals, the control unit detects the selector lever positions. It uses the signals to implement the driver's D-R-S or Tiptronic command and to control starter release. Effects of signal failure If the control unit detects no selector lever position, both clutches are opened.Hall sensors for Tiptronic positionTiptronic switches in steering to shift up and down E438 and E439The switches are located on the right and left on the steering wheel. The gears can be shifted up and down by actuating the switches. The shift signals are transmitted from the steering column electronics control unit J527 to the mechatronic unit for direct shift gearbox J743 via the CAN bus. Signal use In Tiptronic mode, the gears can also be shifted up and down using the steering wheel switches. If the Tiptronic switches on the steering wheel are actuated in automatic mode, the gearbox control system switches to Tiptronic mode. If the Tiptronic switches on the steering wheel are no longer actuated, the gearbox control system automatically switches back to automatic mode following the expiry of a timer. Effects of signal failure In the event of signal failure, no Tiptronic functions are possible via the steering wheel switches.S390_052Hall senders for detecting the selector lever positionE439E438S309_099Tiptronic shifting strategy - Automatic upshifting on reaching the maximum engine speed - Automatic downshifting on falling below the minimum engine speed - Kick-down downshifting59Gearbox management systemActuatorsClutch actuator solenoid valvesValve 3 in gear train half 1 N435, valve 3 in gear train half 2 N439The clutch actuator solenoid valves are located in the mechatronic unit's hydraulic module. They are actuated by the electronic gearbox control unit. They are used to control the oil volume for actuating the clutches.●●Solenoid valve N435 controls the oil volume for clutch K1 Solenoid valve N439 controls the oil volume for clutch K2Valve 3 in gear train half 1 N435 Valve 3 in gear train half 2 N439S390_076Effects of signal failure If one of the solenoid valves fails, the corresponding gear train half is shut off.60Gear train half pressure control valvesValve 4 in gear train half 1 N436, valve 4 in gear train half 2 N440Both valves are solenoid valves, and are located in the mechatronic unit's hydraulic module. Valve 4 in gear train half 1 controls the hydraulic oil pressure to the gear selectors and to the clutch actuator in gear train half 1. Gear train half 1 is used to shift gears 1, 3, 5 and 7. Valve 4 in gear train half 2 controls the hydraulic oil pressure to the gear selectors and to the clutch actuator in gear train half 2.Valve 4 in gear train half 2 N440S390_077Valve 4 in gear train half 1 N436Effects of signal failure If one of the solenoid valves fails, the corresponding gear train half is shut off, and only the gears assigned to the other gear train half can be engaged.61Gearbox management systemGear selector solenoid valvesValve 1 in gear train half 1 N433, valve 2 in gear train half 1 N434, valve 1 in gear train half 2 N437, valve 2 in gear train half 2 N438The gear selector solenoid valves are located in the mechatronic unit's hydraulic module. They are used by the gearbox control unit to control the oil volume to the gear selectors and therefore for changing gears.● ● ● ●N433 gears 1 and 3, gear train half 1 N434 gears 5 and 7, gear train half 1 N437 gears 4 and 2, gear train half 2 N438 gears 6 and R, gear train half 2Valve 2 in gear train half 1 N434Valve 2 in gear train half 2 N438S390_078Valve 1 in gear train half 1 N433Valve 1 in gear train half 2 N437Effects of signal failure If one of the solenoid valves fails, the corresponding gear train half is shut off.62Motor for hydraulic pump V401The motor for the hydraulic pump is integrated into the mechatronic unit's hydraulic module. It is actuated by the gearbox control unit subject to requirements. The control unit shuts the motor off when the hydraulic pressure in the system has reached 60 bar, and switches it on again when the pressure has fallen to 40 bar.S390_079Motor for hydraulic pump V401Effects of signal failure If the motor cannot be actuated, the hydraulic pressure drops and the clutches open independently due to the pressure plates' spring force.63Gearbox management systemFunctional diagramComponents E313 E438 E439 F319 G182 G270 G487 G488 G489 G490 G510 G612 G617 G618 G632 J119 J285 J453 J519 J527 J533 J681 J743 N110 N433 N434 N435 N436 N437 N438 N439 N440 V401 Y6 Selector lever Tiptronic switch in steering wheel to shift up Tiptronic switch in steering wheel to shift down Selector lever locked in position P switch Gearbox input speed sender Gearbox hydraulic pressure sender Gear selector movement sensor 1 Gear selector movement sensor 2 Gear selector movement sensor 3 Gear selector movement sensor 4 Temperature sender in control unit Gearbox input speed sender 2 Clutch travel sender 1 Clutch travel sender 2 Gearbox input speed sender 1 Multifunction display Control unit with display in dash panel insert Multifunction steering wheel control unit Onboard supply control unit Steering column electronics control unit Data bus diagnostic interface Terminal 15 voltage supply relay 2 Mechatronic unit for direct shift gearbox Selector lever lock solenoid Valve 1 in gear train half 1 Valve 2 in gear train half 1 Valve 3 in gear train half 1 Valve 4 in gear train half 1 Valve 1 in gear train half 2 Valve 2 in gear train half 2 Valve 3 in gear train half 2 Valve 4 in gear train half 2 Motor for hydraulic pump Selector lever position display Diagnosis connector64S390_054Input signal Output signal Bi-directionalPositive Ground CAN data bus65Gearbox management systemCAN data bus connectionThe schematic shown below symbolically shows the integration of the mechatronic unit for direct shift gearbox into the vehicle's CAN data bus structure. J104 J248 J285 J519 Control unit for ABS with EDL Diesel direct injection system control unit Control unit with display in dash panel insert Onboard supply control unit J527 J533 J587 J623 J743 Steering column electronics control unit Data bus diagnostic interface Selector lever sensor control unit Engine control unit Mechatronic unit for direct shift gearboxS390_055 Diagnostic connector"Powertrain" CAN data bus CAN "convenience" data bus66DiagnosisDiagnosisVia the vehicle diagnosis, testing and information system VAS 5051 A/B and VAS 5052, the following operating modes: - Guided Fault Finding and - Guided Functions are available.Actuators:N433 N434 N435 N436 N437 N438 N439 N440 V401 Valve 1 in gear train half 1 Valve 2 in gear train half 1 Valve 3 in gear train half 1 Valve 4 in gear train half 1 Valve 1 in gear train half 2 Valve 2 in gear train half 2 Valve 3 in gear train half 2 Valve 4 in gear train half 2 Motor for hydraulic pump"Guided Fault Finding" operating modeA test plan, which can be used to test the following sensors, actuators and the mechatronic unit during operation is contained in "Guided Fault Finding" for the double-clutch gearbox. When testing the sensors and actuators, please observe the instructions in VAS 5051 A/B and VAS 5052.Mechatronic unit:Mechatronic unit defective J743 Mechatronic unit for direct shift gearboxSensors:E438 E439 G182 G270 G487 G488 G489 G490 G510 G612 G617 G618 G632 J587 Tiptronic switch in steering wheel to shift up Tiptronic switch in steering wheel to shift down Gearbox input speed sender Gearbox hydraulic pressure sender Gear selector movement sensor 1 Gear selector movement sensor 2 Gear selector movement sensor 3 Gear selector movement sensor 4 Temperature sender in control unit Gearbox input speed sender 2 Clutch travel sender 1 Clutch travel sender 2 Gearbox input speed sender 1 Selector lever sensor control unit67ServiceSpecial toolsA new special tool is available for aligning gearbox support 3282 of engine and gearbox jack V.A.G 1383 A when removing the gearbox. Adjustment plate 3282/59S390_0956869Test YourselfWhich answers are correct? One or several of the given answers may be correct.1.Which statements about the double-clutch gearbox 0AM are correct? a) The gearbox is equipped with a double clutch. b) The gearbox has 7 forwards gears and one reverse gear. c) The mechatronic unit and the mechanical gearbox each have a separate oil circuit. d) The oil pump is driven subject to requirements.2.Onto which shaft does clutch K1 transmit the engine torque? a) Onto output shaft 2. b) Onto output shaft 1. c) Onto drive shaft 1. d) Onto drive shaft 2.3.Please name the components!1……………………………………………………2……………………………………………………3……………………………………………………4……………………………………………………S390_105704.Please complete the text! …………… independent, …………… clutches operate in the double clutch. They each conduct the engine torque into …………… gear train half. When the engine is switched off, …………… clutches are …………… . During vehicle operation, only …………… of the clutches is ever …………… .5.Which gear is engaged in the illustration? a) 1st gear. b) 4th gear. c) R gear. d) 7th gear.S390_0346.Which statement about the mechatronic unit is correct? a) The mechatronic unit is the central gearbox control unit. b) It consists of one module, in which the electronic control unit and the electrohydraulic control unit are comprised. c) The mechatronic unit has a separate oil circuit. d) It is connected to the oil circuit of the mechanical gearbox.7.Please complete the text! The electrohydraulic control unit is integrated into the …………… . It generates the …………… which is required to …………… and to actuate the …………… .71Test Yourself8. Please name the components!1……………………………………………………2……………………………………………………3……………………………………………………4……………………………………………………S390_1069.Please name the components!1……………………………………………………2……………………………………………………3……………………………………………………4……………………………………………………5S390_104……………………………………………………10. Via valve 2 in gear train half 1 N434, a) 1st and 3rd gears are shifted. b) 4th and 2nd gears are shifted. c) 7th and 5th gears are shifted.7211.Which statement is correct? a) The motor for the hydraulic pump is a brushless DC motor. b) The brushless DC motor is actuated by the engine control unit. c) It drives the hydraulic pump via a coupling.12.Valve 4 in gear train half 2 N440 a) Is a gear train half pressure control valve. b) It controls the oil pressure for gear train half 2. c) Gear train half 1 can be shut off via this valve.13.Please complete the text! The gearbox input speed sender G182 is inserted into the …………… . It electronically scans the starter ring gear and therefore records the …………… . The gearbox input speed signal is required by the control unit to …………… and …………… the clutches. In the event of signal failure, the control unit uses the …………… signal as a substitute signal.14.A clutch travel sender consists of a) An iron core, around which a primary coil is wrapped b) A Hall sender c) Two secondary coils d) A permanent magnet and e) The sensor electronics73Test Yourself15. Which measures are introduced by the electronic gearbox control unit as of a mechatronic unit temperature of approx. 140°C? a) One gear train half is shut off. b) The system immediately shifts to the next highest gear. c) Engine torque reduction is introduced.16. Which measures are introduced if a clutch actuator solenoid valve fails? a) The gear train half for the affected clutch is shut off. b) The affected clutch is no longer actuated. c) The clutch actuator solenoid valve for the other clutch also controls the affected clutch.17.What are the effects if the motor for hydraulic pump fails? a) The hydraulic pressure drops. b) The clutches open independently. c) The failure of a motor for hydraulic pump has no effects, because the hydraulic pump continues to work.7475Answers: 1. a, b, c, d; 2. c; 3. 1 = reverse gear, 2 = 5th gear, 3 = reverse gear intermediate gear, 4 = 1st gear; 4. two independent dryclutches operate, … one gear half train, … both clutches open, … only one of the clutches is ever closed; 5. c; 6. a, b, c; 7. … integrated into the mechatronic module, … the oil pressure, which is required to change the gears …, … the clutches… 8. 1 = Gear selector for gears 5 and 7, 2 = Gearbox input speed sender 2 G612, 3 = Gear selector for gears 2 and 4, 4 = Gearbox input speed sender G182; 9. 1 = Pressure limiting valve, 2 = Pressure accumulator, 3 = Hydraulic pressure sender, 4 = Valve 4 in gear train half 1 N346, 5 = Valve 3 in gear train half 1 N435 10. c; 11. a, c; 12. a, b; 13. … into the gearbox housing, … the gearbox input speed, … to control the clutches and calculate clutch slip, … the engine speed; 14. a, b, d, e; 15. c, 16. a, b; 17. a, b390© VOLKSWAGEN AG, Wolfsburg All rights and rights to make technical alterations reserved. 000.2811.85.20 Technical status 12.2007 Volkswagen AG Service Training VSQ-1 Brieffach 1995 D-38436 Wolfsburg❀ This paper was manufactured from pulp bleached without the use of chlorine.76