TECHNICAL DOCUMENTATION
SSP 467 The 4,2 l V8 TDI engine

This PDF is currently unavailable.
Read document text
Service TrainingSelf-study Programme 467The 4.2 l V8 TDI engine with common rail fuel injection system Design and FunctionFollowing the introduction of the 3.0 l V6 TDI engine in the Phaeton and Touareg in 2005, the engine range is now being expanded to include the 4.2 l V8 TDI engine. Thanks to this range-topping diesel engine, Volkswagen now has a power plant that boasts excellent figures and thus superior performance with 250 kw max. at 4,000 rpm and 800 Nm as early as 1,750 rpm.This high-torque engine, which was developed by Audi and has featured in the A8 and Q7, has been adapted for use in the new Touareg. It has been possible to reach the high emissions goals for the EU5 emissions standard and, at the same time, achieve a consumption of 9.4 l/100 km with 239 g/km CO2. This engine sets standards in terms of dynamics, driving fun, consumption and reliability while improving comfort and reducing noise.S467_002The self-study programme portrays the design and function of new developments. The contents will not be updated.For current testing, adjustment and repair instructions, refer to the relevant service literature.Important Note2ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Engine Mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Engine Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Test Yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 423IntroductionThe 4.2 l V8 TDI engine with common rail injection systemTechnical featuresqqq q q q q qBosch common rail injection system with piezo injectors max. 2,000 bar injection pressure Diesel particulate filter/oxidising catalytic converter Turbochargers with speed sensors Innovative thermal management (ITM) Low-temperature exhaust gas recirculation Volumetric flow-controlled oil pump Demand-regulated fuel delivery unit Oil level/oil temperature sender with ultrasonic measurement principleS467_040Technical dataOutput and torque graph Engine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Max. output in kW Maximum torque Engine management Fuel Exhaust gas treatment CKDA 8-cylinder V engine 4,134 cm3 83.0 mm 95.5 mm 4 16.4 : 1 250 at 4,000 rpm 800 Nm at 1,750 rpm to 2,750 rpm Bosch EDC 17 Diesel fuel complying with DIN EN590 Exhaust gas recirculation, oxidising catalytic converter, diesel particulate filter EURO 5 239 g/km Engine speed (rpm) S467_026 Torque (Nm) Output (kW)Emissions standard CO2 emission4Engine ComponentsCrankshaft driveThe crankcase with a gap of 90 mm between the cylinders (90°V) is made from grey cast iron. The crankshaft is forged and mounted in 5 bearings. The big end bearing journals are roller burnished for strength. Roller burnishing is a non-cutting process that uses rolling tools to smoothen and strengthen material surfaces. The cast aluminium pistons with combustion cavity have a diameter of 83 mm. They are equipped with a ring carrier cooling duct for cooling the piston. Oil spray nozzles constantly spray oil onto the underside of the piston crown.CrankcaseMain oil duct Bearing frameCrankshaftOil sumpS467_0445Engine ComponentsChain driveThe chain drive has been taken from the 4.2 l V8 TDI engine as previously used at Audi, but has been improved in terms of friction and rotational vibration behaviour. The ancillary components, like the oil pump and coolant pump, are driven via the chain drive D and a gear module.Chain drive CChain drive BChain drive AS467_045 Gear moduleChain drive D6Vibration damperThe 4.2 l V8 TDI engine has been equipped with a vibration damper to dampen the vibrations caused by combustion. This results in better engine acoustics and less load on the crankshaft.Counterweight for crankshaftS467_046Rubber track Belt track7Engine ComponentsCamshaft driveBacklash compensationThe intake and exhaust camshafts are linked via spur gear toothing with integrated backlash compensation. In this case, the spur gear on the exhaust camshaft is driven by the spur gear on the intake camshaft. Backlash compensation ensures that the camshafts are driven with little noise.Inlet camshaft Cylinder head (example left) Exhaust camshaft Spur gear on exhaust camshaft q fixed q movingExhaust camshaftS467_004 Spur gear on inlet camshaftMoving spur gearIntermediate disc S467_005Fixed spur gearFixed spur gearDisc spring CirclipMoving spur gearDesignThe exhaust camshaft spur gear is split into two parts in the left-hand cylinder head. (In the right-hand cylinder head, the intake camshaft spur gear is split into two parts.) The broader part of the spur gear (fixed spur gear) is positively connected to the camshaft. Six ramps are located on the front face. The narrower part of the spur gear (moveable spur gear) can be moved radially and axially. Recesses for the six ramps are located on its rear side. 8Ramps S467_006FunctionBoth spur gear parts are pushed together in the axial direction due to the force exerted by a disc spring. At the same time, they are rotated by the ramps.S467_007Disc springThis rotational movement offsets the teeth of both spur gear parts and therefore leads to backlash compensation between the gear wheels on the intake and exhaust camshafts.Tooth offsetS467_0089Engine ComponentsOil systemSchematic overview of system7 9586103421 S467_039Legend 1 2 3 4 5 6 7 8 9 10 Oil sump Oil pump Oil cooler (coolant) Oil pressure control valve Oil filter module Hydraulic camshaft adjustment Cylinder bank 1 Cylinder bank 2 Chain tensioner Piston cooling Coolant supply Coolant return Oil – without pressure Oil – under pressure10Volumetric flow-controlled oil pumpThe 4.2 l V8 TDI engine uses an oil pump with two pressure levels and volumetric flow control. This is a vane cell pump that can change its delivery characteristics thanks to an eccentrically mounted adjustment ring. Engine oil pressure can be applied to the adjustment ring via two control surfaces to turn it against the force of a control spring. This changes the delivered volume. The oil pressure is measured at the main oil gallery downstream of the oil filter and, depending on the required pressure level, oil is sent to one or both control surfaces. The valve for oil pressure control N428 switches between the two pressure levels depending on the engine load, engine speed and oil temperature. The drive power of the oil pump is thus reduced considerably, above all, in the load cycles preferred by customers, like city or long-distance driving.Oil pumpVanesS467_048 Delivery chamber11Engine ComponentsSmall delivery quantityThe valve for oil pressure control N428 is supplied with voltage from terminal 15. The valve is connected to earth via the engine control unit. This opens the oil duct for control surface 2. Oil pressure is always supplied to control surface 1 via a second oil duct. Now both oil flows act on both control surfaces with the same pressure. The resulting forces are greater than the force of the control spring. The adjustment ring turns anti-clockwise and reduces the size of the pump delivery chamber. The small delivery quantity is switched depending on the engine speed, engine load and oil temperature. This reduces the drive power of the oil pump.Valve for oil pressure control N428 – activated Crankshaft oil ductOil pressure applied from crankshaft oil duct Control surface 1S467_027Vane cellsDelivery chamber Control surface 2 S467_03612Large delivery quantityFrom an engine speed of 2,500 rpm or an increased torque (full throttle acceleration), the solenoid valve is disconnected from earth by the engine control unit. The oil duct to control surface 2 is closed. The oil pressure present only acts on control surface 1. This force is lower than the force of the control spring. The control spring rotates the adjustment ring clockwise. The adjustment ring is rotated from the centre position and thus enlarges the delivery chamber between the vane cells. More oil is delivered through the larger delivery chamber. A resistance acts through the oil holes and the bearing play of the crankshaft against the higher oil volume flow. This causes the oil pressure to rise. A volumetric flow-controlled oil pump with two pressure levels is achieved in this way.Valve for oil pressure control N428 (zero current) – closedOil pressure applied from crankshaft oil duct Control surface 1S467_028Vane cellsDelivery chamber Control surface 2S467_03513Engine ComponentsOil level and oil temperature sender G266An electronic oil level and oil temperature sender is used in the 4.2 l V8 TDI engine for the Touareg. The conventional oil dipstick has been omitted. The sender works according to the ultrasound principle. The ultrasonic impulses emitted are reflected by the oil/air boundary layer. Ultrasound is a sound frequency that is above the range perceivable by humans. The ultrasound waves are reflected depending on the material/density of the obstacle. Air and oil have different densities. In oil, the sound waves can spread with low resistance. In air, the dispersion of the sound waves is subject to considerably greater resistance. Therefore the ultrasound waves are reflected at the oil/air boundary layer. The advantages of the ultrasound sender are:q qPower consumption 0.5 A Faster sender signal, approx. 100 msMeasuring unitSeal3-pole connector housingSender foot with measuring electronics S467_04714Operating principleOutput with pulse-width modulated signalTemperature Filling levelDigital LogicEvaluationS467_043The sender consists of the sender foot with measuring electronics, the measuring unit and the 3-pole connector housing. The ultrasound signals are processed in the measuring electronics. A map is used to calculate the oil level from the time difference between the sent and reflected signal. In addition to the oil level, the oil temperature is calculated with a PTC signal. Both values are sent to the dash panel via the engine control unit using a PWM signal (pulsewidth modulation).The display strategy of the oil level display is described in self-study programme no. 452 “The 3.0 l V6 245 kW TSI engine with supercharger in the Touareg Hybrid”.15Engine ComponentsExhaust gas recirculation systemTurbocharger with speed senderSender for turbocharger speed G688Aperture for speed sensorS467_033The 4.2 l V8 TDI engine is equipped with two speed-controlled turbochargers. Featuresq qq qq qWater-cooled VGT turbocharger from Garrett High charge pressure in low rev ranges thanks to optimised compressor wheels Variable turbine geometry Turbocharger with speed sensors to monitor the speed of the turbocharger Improved software functions in engine control unit Better torque and output valuesqqqProtection function against excessive speed in extreme conditions (high elevation/mountain pass driving) Speed reduction when there is a large speed difference between the two turbochargers Turbocharger speed is controlled by evaluation electronics. The turbine wheel with its guide vanes gives off a pulse for each vane. Nine pulses of the turbine wheel represent one revolution of the turbocharger.16Ventilation duct in cylinder headIf there is any leakage around the copper injector seal, the combustion pressure of 180 bar will allow the air to escape from the combustion chamber via a duct. The ventilation duct is located in the cylinder head above the exhaust manifold. It prevents the excess pressure from the combustion chamber reaching the compressor side of the turbocharger, which could cause faults or damage seals.Piezo injectorAccess to crankcase ventilation system via the oil chamber in the cylinder headSealChannel for glow plugS467_059 Seal to combustion chamber Ventilation ductS467_06017Engine ComponentsInnovative thermal managementThe innovative thermal management system (ITM) is being used for the first time in the new VW Touareg. It allows the flow of heat supplied by the engine to be distributed perfectly between the engine, gearbox and interior. To distribute the available heat in an ideal way, new software was developed taking the requirements and priorities of the interior, engine and gearbox into account. The centrepiece is the so-called thermal manager in the engine control unit. This guarantees a comfortable interior climate and optimum usage of the available heat to minimise friction in the engine. The air-conditioning and gearbox control unit signal their heat requirement to engine control unit via the CAN data bus. These are then weighted together with the engine heat requirement calculated by the engine control unit. The individual ITM components are then activated by the engine control unit as required. On the 4.2 l V8 TDI engine, the ITM comprises the following components:qStanding coolant: The engine warms up faster during the warm-up phase resulting in lower engine friction and reduction of the HC and CO emissions. The standing coolant is made possible by an on-demand coolant pump. A vacuumoperated control shutter is pushed over the coolant pump impeller. The coolant pump continues to be driven, but coolant is not pumped. When the vacuum is removed, the control shutter is opened by a set of springs. Cylinder head temperature sensor: A coolant temperature sensor is used in the cylinder head close to the combustion chamber to monitor the critical valve bridge temperature and to avoid boiling coolant during the standing coolant mode. The coolant pump is activated using a load/engine speed-dependent map to protect components when there are large load jumps. Gearbox oil heating: Immediately after the coolant pump is switched on, the coolant that has already been heated up in the small engine circuit is made available to the gearbox oil cooler via an electrically operated directional valve. The faster heating up of the gearbox oil also reduces frictional losses in this area during the warm-up phase. Heating shut-off: If no heating is required, the complete thermal capacity of the interior heating can be switched off. As a result, the engine does not have to provide heat during the warm-up phase.qqq18Thermal management – schematic diagramThe schematic diagram shows in a simplified manner how the “Innovative Thermal Management” system works. The heat produced by the engine is utilised in an ideal way and is passed onto the interior climate control and the gearbox as required. The individual components signal their heat requirement to the engine control unit and the components are activated depending on the priority.Electrical pumpCylinder headGearboxInteriorMain radiatorEngine blockMain coolant pumpThermostatS467_02919Engine ComponentsCoolant circuitOn-demand coolant pumpThe “Innovative Thermal Management” system used with the 4.2 l V8 TDI engine makes use of an on-demand coolant pump.Standing coolantWhen the engine is cold, the on-demand coolant pump stops the circulation of the coolant. This state is called standing coolant. The coolant circuit solenoid valve N492 pushes a vacuum-operated control shutter over the spinning vane rotor in the coolant pump. This stops the circulation of coolant. The coolant heats up more quickly and shortens the engine warm-up phase considerably. The heated coolant is sent to the automatic gearbox to also actively heat it. Heating the engine and gearbox oil more quickly reduces internal friction. This reduces the consumption and CO2 emissions.Control shutter Guide rod Ring piston Rolling diaphragmRod seal Friction bearingVacuum connection By-pass sealImpellerS467_03020Circulating coolantWhen no vacuum is applied, the control shutter is pressed into its resting position by return springs inside the coolant pump. The coolant circulates and heats the thermostat to activate the large cooling circuit. This ensures circulation of the coolant at all times (fail-safe).Thermostat opens from a coolant temperature of 87 °CControl shutterReturn springRolling diaphragmS467_03121Engine ComponentsLow-temperature exhaust gas recirculationThe low-temperature exhaust gas recirculation system is used to minimise nitrogen oxide (NO x), which is formed when diesel fuel is burnt.EGR valve cylinder bank 1 EGR cooler with bypass valveThermostat for exhaust gas recirculation coolingEGR valve cylinder bank 2 Pump for exhaust gas recirculation cooler V400S467_013The pump for exhaust gas recirculation cooler V400 is activated immediately upon engine start. The temperature in the exhaust gas recirculation cooler is regulated to 55°C by the thermostat.22The pump for exhaust gas recirculation cooler V400 supplies the low-temperature circuit with cold coolant directly from the main radiator. The pump is activated immediately upon engine start. The EGR cooler is integrated in its own low-temperature cooling circuit. It is no longer part of the small engine cooling circuit. Advantagesq qConsiderable increase in cooling performance Independent EGR cooling is also possible during the warm-up phaseThe EGR valves regulate the exhaust gas recirculation rates. A differential pressure sender is also fitted in the EGR valve. The differential pressure sender measures the pressure on the intake side. The value from the differential pressure sender and the value from the air mass meter are processed in the engine control unit. The differential pressure sender has been added because, due to the design, the air mass meter is quite far away from the actual cylinder inlet.EGR valve (cylinder bank 1) Differential pressure senderDifferential pressure sender EGR valve (cylinder bank 2)S467_061In extreme engine load conditions, engine running faults could result if only the value from the air mass meter is available. The engine control unit works with both values to avoid this. This guarantees a stable measuring value for the intake air across all engine-speed and torque ranges. Advantagesq q qMore exact measured values Faster regulation is possible Almost same pressure and load relationships on both cylinder banksIf the differential pressure sender signal fails, an entry is made in the fault memory and the engine control unit works with the value from the air mass meter.23Engine ComponentsLow-pressure fuel systemFuel systemThe fuel system is divided into three pressure areasq q q1 - Fuel delivery unit GX1 2 - Pressure-resistant fuel filter 3 - Fuel temperature sender G81 Calculates the current fuel temperature. 4 - High-pressure pump Generates the high fuel pressure required for injection. 5 - Fuel metering valve N290 Controls the quantity of fuel to be pressurised as required. 6 - Pressure retention valve Maintains the return pressure of the injectors at approx. 10 bar. This pressure is required for the injectors to work.High pressure up to 2000 bar Return pressure from the injectors 10 bar Supply pressure, return pressureIn the fuel supply system, the fuel is delivered by the fuel delivery unit from the fuel tank through the fuel filter to the high-pressure pump as required. The fuel delivery unit supplies the fuel pressure as required. The engine control unit calculates the current fuel requirement from the accelerator position, torque, engine temperature etc. and sends a corresponding signal to the fuel pump control unit. The fuel pump runs fast or slow accordingly. The high fuel pressure required for injection is generated in the high-pressure pump and is fed into the high-pressure accumulator (rail). The fuel reaches the injectors from the high-pressure accumulator. The pressure retention valve in the overflow diesel oil line maintains the injector return pressure at 10 bar. This pressure is important for operation of the piezo injectors.2High pressure Supply pressure Return pressure Return from the injectors 111247 - Engine control unit J623 8 - Fuel pressure sender G247 Measures the current fuel pressure in the highpressure area. 9 - Fuel pressure regulating valve N276 Sets the fuel pressure in the high-pressure area.10 - Injectors 11 - Fuel pump control unit J538 12 - High-pressure accumulator (rail) Stores the fuel required for injection into all cylinders under high pressure.10 6Cylinder bank 2 12 85 3 4 Cylinder bank 1 12 9107S467_04225Engine ComponentsFuel delivery unit GX1The fuel pump is an electrically driven annular gear pump and produces a fuel pressure of 3.5 to 6 bar at a maximum of 220 l/h. The fuel pressure is regulated according to requirements. Function The engine control unit calculates the current fuel requirement from the accelerator position, torque, engine temperature etc. and sends a PWM signal to the fuel pump control unit J538. The fuel pump control unit is mounted on the fuel tank. The control unit sends a corresponding command (signal) to the fuel pump. As a result, the fuel pump runs faster or slower and supplies the requested volume of fuel. Thanks to the fuel pump being activated on demand, an additional pre-supply pump is no longer required and has been omitted.Fuel line for auxiliary heatingFuel returnFuel supply systemElectrical connection Fuel delivery unitFuel pumpS467 05626Functional diagramCAN data busS467 022Legend GX1 G1 G3 J285 J538 J623 K29 K132 K231 Fuel delivery unit Fuel gauge Coolant temperature gauge Control unit in dash panel insert Fuel pump control unit Engine control unit Glow period warning lamp Electronic power control fault lamp Diesel particulate filter warning lamp Input signal Output signal Positive Ground CAN data bus27Engine ComponentsCommon rail fuel injection systemBasic explanationThe 4.2 l V8 TDI engine in the Touareg is equipped with a Bosch common rail injection system for mixture preparation. In this system, pressure generation and fuel injection are separate. The high-pressure pump generates the high fuel pressure required for injection. The common rail fuel injection system is controlled by the Bosch EDC 17 engine management system.qqThe injection pressure is instantly available and is adapted to the current engine operating status Flexible fuel injection process, with several pilot and secondary injection processes.Fuel line to high-pressure accumulator (rail) Fuel pressure regulating valve N276 High-pressure pump Fuel metering valve N290High-pressure accumulator (rail) cylinder bank 1High-pressure accumulator (rail) cylinder bank 2Fuel distributor between the railsFuel pressure sender G247 S467_055 InjectorsInjectors28Restrictors in the railWhen the injector is closed and during subsequent injections, a pressure wave from the injector is built up. This continues up to the rail and is reflected from there again. To dampen the pressure waves, restrictors are fitted in the fuel supply from the high-pressure pump to the high-pressure accumulators (rails), on the highpressure accumulators (rails) for cylinder banks 1 and 2 and in the rails in front of each injector.The correct tightening torque must be used when tightening the injector fuel line and also the line connecting the two rails. Deformed or damaged high-pressure lines may not be used again – they have to be replaced.High-pressure lineUnion nutRestrictorRailS467_06629Engine ComponentsHigh-pressure pumpThe high-pressure pump is a 2-piston pump. The pump is driven by a toothed belt. It generates the high fuel pressure of up to 2000 bar that is required for injection.Design of high-pressure pumpIntake valveFuel metering valve N290 Outlet valvePump plungerConnection to railFuel inlet Plunger spring Fuel returnRoller Overflow valveDrive shaftS467_049 Drive cam30Design of high-pressure pump – schematicIntake valve Outlet valveFuel metering valve N290Connection to rail Pump plunger Plunger springFine filterOverflow valveRollerDrive shaft with cam S467_053Fuel return Fuel inlet31Engine ComponentsHigh-pressure fuel systemFuel metering valve N290The fuel metering valve N290 is integrated into the high-pressure pump. The valve regulates the fuel quantity that is required to produce high pressure. The advantage of this is that the high-pressure pump only has to pressurise the amount of fuel that is required for the current operating conditions. This reduces the power consumption of the high-pressure pump and avoids unnecessary fuel heating.To compression chamber Control plungerInlet from inside of pumpS467_052Function When no current is supplied, the fuel metering valve is open. To reduce the quantity flowing to the compression chamber, the valve is actuated by the engine control unit with a pulse-width modulated (PWM) signal. The fuel metering valve is pulsed closed by the PWM signal. The quantity of fuel flowing into the compression chamber of the high-pressure pump varies in relation to the PWM signal. 32Fuel pressure regulating valve N276The fuel pressure regulating valve is located on the high-pressure accumulator (rail) for cylinder bank 1. The fuel pressure is set in the high-pressure area by opening and closing the regulating valve. To do this, the regulating valve is actuated by the engine control unit with a pulse-width-modulated signal.High-pressure accumulator (rail)- cylinder bank 1 Fuel pressure regulating valve N276S467_058DesignElectrical connection High-pressure accumulator (rail) Solenoid Valve needle Valve armatureS467_051 Return to the fuel tank Valve spring33Engine ComponentsFunction Regulating valve in resting position (engine “off”) If the regulating valve is not actuated, the pressure regulating valve is opened by the valve springs. The high-pressure area is connected to the fuel return line. This ensures a volume balance between the fuel highpressure and low-pressure area. Vapour bubbles, which can form in the high-pressure accumulator (rail) during the cooling process after the engine is switched off, are avoided and the starting behaviour of the engine is thus improved.S467_015 Valve springsRegulating valve actuated (engine "on") To attain an operating pressure of 230 to 2,000 bar in the high-pressure accumulator, the regulating valve is actuated by the engine control unit J623 using a pulse-width modulated (PWM) signal. This creates a magnetic field in the solenoid. The valve armature is attracted and presses the valve needle into its seat. The fuel pressure in the high-pressure accumulator is therefore opposed by a magnetic force. Depending on the on-off ratio of actuation, the flow to the return line and therefore the quantity flowing back is varied. This also enables pressure fluctuations in the highpressure accumulator to be compensated for.Engine control unit J623S467_016Effects upon failure The engine will not run if the fuel pressure regulating valve fails because it is not possible to build up sufficient fuel pressure for fuel injection.34Regulation of the high-pressure fuelIn the common rail injection system, the high-pressure fuel is regulated with a so-called dual-regulation design. The fuel pressure regulating valve N276 and the fuel metering valve N290 are actuated by the engine control unit using a pulse-width modulated signal (PWM signal) for this purpose. Depending on the operating status of the engine, the high fuel pressure is regulated by one of the two valves. The other valve is then only controlled by the engine control unit.Regulation by the fuel pressure regulating valve N276 When the engine is started and the fuel needs warming, the high fuel pressure is regulated by the fuel pressure regulating valve N276. To warm up the fuel quickly, the high-pressure pump delivers and pressurises more fuel than is required. The excess fuel is returned to the fuel return line by the fuel pressure regulating valve N276.Regulation by the fuel metering valve N290 When there are large injection quantities and high rail pressures, the high fuel pressure is regulated by the fuel metering valve N290. This results in ondemand control of the high fuel pressure. The power consumption of the high-pressure pump is reduced and unnecessary fuel heating is avoided.Control by both valves During idling and overrun and when there are small injection quantities, the fuel pressure is regulated by both valves at the same time. This allows precise regulation, which improves the idling quality and the transition to overrun.Schematic diagram of dual-regulation designRegulation of the high pressure fuel by the fuel pressure regulating valve N276 Injection quantityRegulation of the high-pressure fuel by the fuel metering valve N290Regulation by both valves Engine speed S467_05435Engine ComponentsInjectorsPiezo-controlled injectors are used in the common rail injection system for the Touareg 4.2 l TDI engine. The injectors are controlled via a piezo actuator. This results in the following advantages:q q qVery short switching times Several injections per working cycle are possible Precise proportional injection quantitiesElectrical connection Fuel inlet (high-pressure connection) Pin-type filterFuel returnPiezo actuatorConnecting plunger Valve plunger Valve plunger spring Switching valveRestrictor plate Nozzle springSeal Nozzle needle S467_01436Injection processThe very short switching times of the piezo-controlled injectors allow flexible and precise control of the injection phases and injection quantities. As a result, the injection process can be adapted to the relevant operating requirements of the engine. Up to five partial injections can be carried out per injection process.Initialisation voltage (V)Injection (rate of injection) Pilot injection Main injection Secondary injectionTime S467_050Pilot injectionA small quantity of fuel is injected into the combustion chamber prior to main injection. This leads to a rise in temperature and pressure in the combustion chamber. The main injection ignition time lag is therefore shortened, thereby reducing the rise in pressure and pressure peaks in the combustion chamber. The results are low combustion noise and low exhaust gas emissions. The number, time and injection quantities of the pilot injection processes are dependent on the engine operating status. When the engine is cold and at low engine speeds, two pilot injections are carried out for acoustic reasons. At higher loads and engine speeds, only one pilot injection is carried out in order to reduce exhaust emissions. No pilot injection is carried out at full throttle and high engine speeds because a large quantity of fuel has to be injected to achieve a high level of efficiency.Main injectionFollowing pilot injection, the main injection quantity is injected into the combustion chamber following a brief injection pause. The injection pressure level remains virtually constant throughout the entire injection process.Secondary injectionTwo secondary injection processes are carried out to regenerate a diesel particulate filter. These secondary injections increase the exhaust gas temperature, which is necessary to combust the soot particles in the diesel particulate filter.37Engine ManagementSystem overviewSensorsAir mass meter G70 Charge pressure sender G31 Intake air temperature sender G42 Engine speed sender G28 Glow period warning lamp K29 Exhaust emissions warning lamp K83 Coolant temperature sender G62 Diesel particulate filter warning lamp K231 Oil temperature sender G8Fuel pressure sender G247Radiator outlet coolant temperature sender G83Hall sender G40Engine control unit J623 (master) Elevation senderAccelerator position sender G79 Accelerator position sender 2 G185 Exhaust gas pressure sensor 1 G450Engine control unit J623 (slave)Exhaust gas temperature sender 1 G235 Lambda probe G39 Exhaust gas temperature sender 1 for bank 2 G236 Air mass meter 2 G246 Exhaust gas temperature sender 3 for bank 2 G497 Catalytic converter check temperature sensor 2 G29 Lambda probe 2 G108 Exhaust gas pressure sensor 2 G451Catalytic converter temperature sensor 1 G20Exhaust gas temperature sender 3 G495Exhaust gas temperature sender 4 G648Oil level and oil temperature sender G266Brake light switch F38CAN LOWControl unit in dash panel insert J285Powertrain CAN data busFuel temperature sender G81 CAN HIGHActuatorsInjectors for cylinders 1, 4, 6, 7 N30, N33, N84, N85 Automatic glow period control unit J179/ Glow plugs for cylinders 1, 4, 6, 7 Q10, Q13, Q15, Q16 Fuel pressure regulating valve N276 Throttle valve module J338 Intake manifold flap motor V157 Exhaust gas recirculation control motor V338 Fuel metering valve N290 Exhaust gas recirculation cooler changeover valve N345 Engine component current supply relay J757 Fuel pump control unit J538 Fuel delivery unit GX1 Diagnostic connector T16 Lambda probe heater Z19 Coolant circulation pump V50 Pump for exhaust gas recirculation cooler V400Turbocharger 1 control unit J724 Turbocharger 2 control unit J725Injectors for cylinders 2, 3, 5, 8 N31, N32, N83, N86Lambda probe heater 2 Z28Intake manifold flap 2 motor V275Glow period control unit 2 J703/ glow plugs for cylinders 2, 3, 5, 8 Q11, Q12, Q14, Q17Exhaust gas recirculation control motor 2 V339S467_017Throttle valve module 2 J54439ServiceSpecial toolsDesignation T40094 T40094/1 T40094/2 T40094/9 T40094/10 T40094/11 T40094/12 Camshaft fitting tool Mount Mount Mount Mount Cap Mount Tool Application For removing and fitting the camshaftsS467_062T40095Camshaft fitting toolFor removing and fitting the camshaftsS467_06340Designation T40096 Camshaft fitting toolToolApplication For fitting the camshaftsS467_064T40178Oil gauge testerFor checking the oil level when there are system errorsS467_06541Test YourselfWhich answers are correct? One or several of the given answers may be correct.1.Which statement about the oil pump is correct? a) The oil pump works with only one pressure level. b) The oil pump can change its delivery characteristics via an eccentrically mounted adjustment ring. c) The oil pump generates up to 4 pressure levels depending on the load.2.Which statement about the oil level and oil temperature sender G266 is correct? a) The sender operates according to the Hall principle. b) The sender uses the heat conduction method. c) The sender operates according to the ultrasound principle.3.What is the advantage of the innovative thermal management system? a) The heat produced by the engine is distributed optimally among the components. b) The heat produced by the engine is always passed on first to the gearbox. c) The heat produced by the engine is always passed on first to the interior heating.4.Where is the fuel pressure in the low pressure area of up to 6 bar regulated on the 4.2 l V8 TDI? a) In the high-pressure pump b) In the pre-supply pump c) In the fuel delivery unit425.What is the purpose of camshaft spur gear backlash compensation? a) Backlash compensation ensures that the camshafts are driven with little noise. b) Backlash compensation ensures that the intake camshaft is adjusted at high engine speeds. c) Backlash compensation ensures rigid engine speed compensation between the gears on the intake and exhaust camshafts.6.Which statement about the turbocharger with speed sender is correct? a) Lower torque and output values b) Speed reduction when there is a large speed difference between the two turbochargers c) Fixed turbine geometryAnswers 1. b); 2. c); 3. a), b); 4. c); 5. a); 6. b) 43467© VOLKSWAGEN AG, Wolfsburg All rights and rights to make technical alterations reserved. 000.2812.39.20 Technical status 07.2010 Volkswagen AG After Sales Qualifizierung Service Training VSQ-1 Brieffach 1995 D-38436 WolfsburgY This paper was manufactured from pulp bleached without the use of chlorine.