TECHNICAL DOCUMENTATION

SSP 474 The Vento 2011 (India)

PDFEN52 pages4 MB
SSP 474 The Vento 2011 (India) - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingSelf-study Programme 474The Vento 2011 (India) This self-study programme provides you with an overview of the design and function of the new Vento, which is destined mainly for the Asian market. Self-study programmes support you in your daily work routine. They help you to understand technical correlations better. Armed with this knowledge, you will be able to provide customers and colleagues with clear information. In some of the chapters, you will find references to self-study programmes that deal in greater detail with with design of individual vehicle components. These and other references are highlighted with a red exclamation mark. Useful information about individual assembly groups can also be found in previous self-study programmes: no. 447 "The Polo 2011", no. 190 "Adjustable turbocharger", no. 237 "Manual gearbox 02T", no. 238 "Data exchange on the CAN bus I", no. 260 "The 1.2 ltr. 3-cylinder engines", no. 269 "Data exchange on the CAN databus II", no. 296 "The 1.4 ltr. and 1.6 ltr. FSI engine with timing chain", no. 309 "6-speed automatic gearbox 09G/09K/09M" and no. 442 "The 1.6 ltr. TDI engine with common rail injection system".S474_003hS474_003gS474_003aS474_003jS474_003cS474_003bS474_003iS474_003eS474_003fThe self-study programme portrays the design and function of new developments. The contents will not be updated.For current testing, adjustment and repair instructions, refer to the relevant service literature.Attention Note2 ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Occupant safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22Engines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23Power transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30Running gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32Electrical system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Convenience electronics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Radio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46Heating and air conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 483 IntroductionThe Vento 2011The new Vento is based on the Polo 2011 and is built at the Volkswagen Pune factory in India. The Pune factory is one of Volkswagen Group's most modern production lines in the world.Pune, IndiaThe whole production programme comprises complete manufacture from forming the panels to constructing the body and final assembly. The maximum annual capacity is designed to accommodate up to 110,000 vehicles. Currently, approx. 2,000 people are employed in Pune and they also produce the Skoda Fabia among other things. Since April 2009, the Polo is built here and since August 2010 the new Vento is built here for the Indian market.Maharastra Mumbai PuneS474_0154 Among the biggest single investments were the construction of a new paintshop, a new bodyshop and a new assembly line for the Polo and the Vento. A fully fledged automobile factory took shape with its own logistics, quality assurance, Volkswagen Academy and all of the associated areas.S474_001S474_9985 IntroductionThe Vento 2011The Vento is the benchmark in the compact segment of the Indian car market. It is offered exclusively as a 4-door version for model year 2011 and is based on the Polo 2011. The product properties of this new Volkswagen model are as follows:●Halogen H4 headlights with chromeplated bezel●Dash panel insert with 7" display●Electro-mechanical power steering (C-EPS)Vento●Braking system with ABS Bosch 8.2 (Highline equipment)●Crash-optimised pedals and crash-optimised steering column6 ●Galvanised body elements (6 year guarantee against rust perforation)●6-speed automatic gearbox 09G (optional)●Rear axle with torsion beam design●Front disc brakesS474_067●Manual air conditioning as standard, Climatronic (optional) at Highline equipment level●Rear lid opening via remote release inside vehicle (switch in driver's door) and mechanical release outside vehicle via lock cylinder7 IntroductionTechnical dataExterior dimensions and weightsThe diagram shows the exterior dimensions of the new Vento.2552mm 4384mmVento1465mmVento1460mm 1699mm 1498mmS474_306Exterior dimensionsLength Width Height Wheelbase Front track width Rear track width 4384mm 1699mm 1465mm 2552mm 1460mm 1498mmWeights and other dataMax. perm. weight Curb weight Tank capacity Drag coefficient 1660kg/ 1700kg (automatic) 1159kg/ 1217kg (automatic) 55litre 0,319cw8 Interior dimensionsThe diagram shows the interior dimensions, the seating positions and the boot of the new Vento.1744mm975 m m941 m m454 litresS474_304Interior dimensions and volumesInterior length Front headroom Rear headroom Boot volume 1744mm 975mm 941mm 454 litreThe equipment linesEquipment features* Manual air conditioning Radio preparation inc. 4 loudspeakers Electric window regulators at front and rear Height adjustable driver's seat Central locking, remote release of boot Power steering (C-EPS) Anti-lock braking system (ABS) Driver and front passenger airbag "India Top Power" radio Radio remote control Electric window regulators with rollback function Climatronic Anti-theft alarm system with interior monitoring Park distance control(*Excerpt)Trendline x x x x x xHighlinex x x x x x x x x x x x9 BodyThe body structureUp to the B-pillar, the new Vento is largely identical to the Polo 2011. All of the components have been designed with function and load in mind in order to achieve an optimum level of strength and rigidity in the body.Strength of steel panels up to 140MPa 140-300MPa 300-1000MPa over 1000MPa (thermally reshaped)No roof load is permissible due to the roof structure of the Vento.S474_039Panel qualitiesThe body is galvanised in all corrosion-relevant areas and comprises, for the main part, high tensile and highest tensile steel panels. This means, for example, that the front and rear side members, the B-pillars and the floorpan plates on the front left and right are made of this high tensile sheet metal.Thermally reshaped panelsThermally reshaped steel panels are used for the Bpillar and in the body area bordering the A-pillar. The strength of these components is achieved before and after the thermal reshaping process by targeted heat treatment in the manufacturing tool. Thermally reshaped steel panels offer a higher tensile strength at a lower weight than normal steel panels.10 Joining processIn addition to classic resistance spot welding, the following joining processes are employed on the bodyshell of the Vento:● ● ● ●Spot welding Adhesive bonding MIG brazing Laser brazingLaser brazingSide panel Laser brazed seam RoofThe Pune factory is a keen proponent of laser brazing technology for the production of bodyshells for the new Vento. In the roof and side panel area and also in the rear lid area, the body components are joined by a laser brazed bond. Laser brazing technology increases the quality of manufacturing and the body by reducing the welding surface, thereby reducing inherent panel deformation. This improves body stability considerably.S474_020Adhesive bondingAdhesive bonding Outer skinA new bonding process is employed on the bonnet and rear lid of the Vento. The panels (outer skin and inner skin) are joined using an adhesive bond. Advantages:● ●Consistent appearance Low cost procedureInner skinS474_14011 BodyBumpersThe bumpers of the Vento are completely colour coded to the vehicle. They are airflow-optimised body elements in an area of the vehicle close to the ground. Thanks to this, air flows along the underside with little swirl, dispensing with the need for a PVC underbody shell. In this way, the weight of the vehicle was further reduced. Together with the airflow-optimised body upper structure, the Vento thereby has a coefficient drag factor (cd value) of just 0.319, which can be considered good for its class.FrontThe front bumper is made up of the following components:● ● ● ● ● ●Bumper coverBumper cover Towing eye cap Blanking plate (fog lamps) Radiator grille Vent grille Bumper carrier (inner)S474_118Vent grilleBlanking plate (fog lamp)RearThe rear bumper comprises the following components:● ● ●Bumper coverBumper cover (one-piece) Lower spoiler, integrated in bumper cover Bumper carrier (inner) moulded foam designS474_116 Integrated spoiler Moulded foam (inner)12 Crash safetyThe following deals with design measures pertaining to crash safety. These measures affect, among other things:● ● ●the steering the pedals the side impact protectionSteeringThe steering column has a telescopic rod design in the bottom section. This area represents the collapsible part shown in the diagram. In the event of a severe frontal collision, the steering column collapses and does not penetrate further into the passenger compartment.S474_090Collapsible part of steering column13 BodyFoot pedal clusterIn severe frontal collisions with major deformation of the vehicle structure, the brake pedal is pivoted out of the foot area by a bending strut. This function is determined by deformation of the bulkhead. The actuation position of the brake pedal is irrelevant.Central pipeBending strutIn a front collision, the foot pedal cluster is pushed towards the central pipe. This results in deflection of the bending strut, which in turn causes the piston rod to bend.Piston rodThe pedal foot plate is pushed away up to max. 170mm. The bending of the piston rod and consequent altering of the shape means that the risk of feet becoming trapped by the pedal in an accident is reduced.S474_00614 Side impact protectionThe side impact protection carriers are made of high tensile steel and are fitted diagonally in the doors. These bend upwards or downwards in the event of frontal or rear-end collision and do not intrude into the A, B and C-pillar. This eases access for rescue and recovery teams as the doors are not blocked by the side impact protection. The diagonal layout of the side impact protection increases the coverage. This means that in the event of an accident with side impact, the side impact protection is hit even at different crash heights. This absorbs the energy of the impact and transmits it to the side of the body.Front doorRear doorS474_130 Door frame Side impact protection cross memberDoor frameSide impact protection cross memberS474_31815 BodyThe headlight modulesA H4 headlight is fitted as standard. This headlight is distinguished by good exploitation of the light source and a sturdy design. The headlight modules feature a turn signal, side light, dipped beam and main beam. An additional turn signal (or side repeater) is located in the wing on each side.Turn signal (21W)S474_042Side light (5W)Dipped beam (55W) Main beam (60W)For the Vento, the headlight modules are installed with chrome-plated bezels. The headlight design features clear-lens technology. The bulbs are connected to the reflector via a metal bar attachment.The fog lightsThe Vento can be equipped as an option with front fog lights. These are located on the left and right in the bumper cover.Front fog light (51W)S474_11816 The tail lights with shutterLeft tail light Right tail lightTail light (5W)Brake light (21W)Brake light (21W)Tail light (5W)S474_038 Turn signal (21W) Reversing light (21W)S474_040 Rear fog lamp (21W) Turn signal (21W)The tail lights have a one-piece design. The light incorporates:● ● ● ● ● ●Replacing bulbsTo access the bulbs, the light must be removed. This is done by removing a central screw behind the luggage compartment trim and subsequently disconnecting the bulb carrier.Tail light Brake light Turn signal Rear fog light (right) Reversing light (left) Reflector17 BodyThe anti-theft protectionThe following deals with design measures pertaining to anti-theft protection. Among these measures are: 1 2 3 4 Cover for bonnet catch 4th generation electronic immobilizer Slip coupling on steering column Lock cylinder freewheel for steering column lock 5 6 7 Anti-theft alarm system with interior monitoring Lock cylinder freewheel for exterior door handles Encapsulated interior door locks with inner profile key53 1 2467S474_069The door lockThe door lock is encapsulated and behind the door handle is a metal plate. These measures prevent penetration and levering up of the door handle in this area.The front coverA cover for the bonnet catch inhibits unauthorised access to the engine compartment.Door handle Metal plate LockCoverS474_012S474_01318 The interior equipmentStowage compartmentsThere are many multifunctional stowage compartments inside the Vento:Glove compartmentSide compartment with bottle holderCompartment in centre armrestFolding paddingS474_310 Compartment for coins and card-holder Glasses tray Compartment with ashtrayS474_312 Pen holder Drinks holder for rear areaFront and in doorsLocated in the centre console are two compartments as standard with round openings for cans/bottles. On the smoker's version, there is also a removable round ashtray included. In the lid of the glove compartment are separate compartments for sunglasses, coins and a cardholder. Moulded into the door trim panels are stowage compartments and bottle holders with 1 L capacity in- the front and 0.5 L in the rear.In the centre armrestThe Vento features a centre armrest for the driver asstandard. In the centre armrest, beneath the hinged padded top, there is an additional stowage compartment. Under this rest are compartments for pens/pencils. On the rear of the rest there is a drinks holder for the rear area. This drinks holder can be folded out from top to bottom.19 BodyLuggage compartmentThe volume of the boot space is 454 litres. Under the floor covering of the boot space is the spare wheel well. In the spare wheel well is a removable box, vehicle tools, warning triangle, first aid box, replacement bulbs and a normal spare wheel.Lock cylinderBoot floor coverLuggage compartment Removable box (bottom part of boot floor)Spare wheel Vehicle toolsS474_300The seating conceptRear seatsThe rear seats of the Vento form one complete and fixed system that cannot be folded. The head restraints on the left and right are height adjustable. A centre armrest is available as an option on the Trendline equipment version and is standard on the Highline version.Head restraintsFolding armrest (optional)S474_06520 Front seatsThe front seats are padded and formed to match the body contour. The height adjustment is optional on the Trendline version and included for the driver seat on the Highline version. The tilt angle of the backrest is adjusted via a lever (detent). On the Highline version, the front seats also have a storage pocket on the rear.Lever for backrest tilt adjustmentLever for seat height adjustment (optional)S474_126Chauffeur functionThe front passenger seat in the Vento can be released from the rear on the Highline version (also known as chauffeur function). This function allows passengers in the rear to push the seat forwards for more space.S474_13621 Occupant safetyThe safety equipmentAirbagsThe Highline equipment version includes driver and front passenger airbags. The driver airbag has a volume of 60litres and the front passenger airbag has a volume of 80litres.S474_055Seat beltsThe front seat belts in the Vento are height adjustable as standard. The rear bench seat features three-point lap belts on the left and right seats. The middle seat has a two-point lap belt.3-point lap beltsAdjustable front belt tensioner2-point lap beltS474_144S474_12222 EnginesThe engine/gearbox combinationsPetrol engine1.6l 77 kW 4-cylinder MPI1.6l 77 kW 4-cylinder TDIDiesel engine5-speed manual gearbox MQ200-5F 02T5-speed manual gearbox MQ250-5F 02R6-speed automatic gearbox AQ250-6F 09G23 EnginesThe 1.6l 77kW CR TDI engineTechnical featuresGrey cast iron cylinder block Common rail injection system with piezo injectors and an injection pressure of max. 1600bar Adjustable turbocharger Exhaust gas recirculation module, comprising exhaust gas recirculation valve and cooler for exhaust gas recirculation Oxidising catalytic converter Plastic intake manifold Software adapted for 77kWS474_049-Further information about this engine can be found in self-study programme no. 442 "The 1.6l TDI engine with common rail injection system".Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel Exhaust gas treatment Emissions standard CO2 emissions CLNA 4-cylinder inline engine 1598cm3 79.5mm 80.5mm 4 16.5:1 77kW at 4400 rpm 250Nm at 1500-2500 rpm Continental PCR2 Diesel compliant with DIN EN590 Exhaust gas recirculation, oxidising catalytic converter Bharat stage 4*/EU4 129g/kmOutput and torque curve[Nm] 240 210 180 150 120 90 60 30 [kW] 80 70 60 50 40 30 20 101000 * Legally prescribed emissions level in India30005000[rpm]Output [kW] Torque [Nm]S474_08824 Ceramic glow plugsNew glow plugs with ceramic heater elements are used on diesel engines with oxidising catalytic converters. Two different sizes are used for the different diesel engine types. There is a narrow version with M8 thread for the 4-valve diesel engine and a short version with M10 thread for the 2-valve diesel engine.S474_025Advantages of ceramic glow plugs: Better cold starting thanks to higher pre and post glow temperatures Improved emissions due to overall higher glow temperatures Reduced ageing2-valve diesel enginesEither Bosch, NGK or Beru glow plugs are installed in the engine.4-valve diesel enginesProtective ceramic casing S354_024Connecting pinPlug bodyCeramic heating elementThe ceramic glow plugs are made up of connecting pin, plug casing and heating element. The heating element is made of an insulating protective ceramic casing and an inner conductive heating element that substitutes the tasks performed by regulating and heating coils in metal glow plugs. The ceramic glow plug has a nominal voltage of 7 volts.25 EnginesThe 1.6ltr. 77kW MPI engine with intake manifold injectionTechnical features● ● ● ● ● ●● ●Grey cast iron cylinder block Intake manifold injection Camshaft driven via chain Reduced main bearing diameter Sheet metal oil sump Pre-heating for crankcase breather system integrated in cooling system Non-return fuel system Exhaust manifold and three-way catalytic converter joined to form one moduleS474_009Technical dataOutput and torque curve[Nm] 160 [kW] 80Engine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management FuelCLSA 4-cylinder inline engine 1598cm3 76.5mm 86.9mm 4 10.5 : 1 77kW at 5250 rpm 153Nm at 3750 rpm Magneti Marelli 7GV Premium petrol RON 95/93 (at least RON 87, but with reduced output) Main catalytic converter with lambda control Bharat stage 4*/EU4140 120 100 80 60 40 20 1000 2000 3000 4000 50007060 50 40 30Exhaust gas treatment Emissions standard20 10 6000 [rpm]Output [kW] - 77kW Torque [Nm] - 77kW * Legally prescribed emissions level in IndiaS474_02226 Cylinder head and cylinder head coverThe cylinder head is the same as that fitted to the 1.4l/66kW FSI engine bar a few modifications. Several changes have been made to the valve train due to the greater loads and exhaust gas temperatures. The exhaust valves are chrome-plated and the valve guides have a higher strength rating. When installing and removing the cylinder head cover, it is essential that the prescribed steps are performed in order. These can be found in ELSA. The diagram of the cylinder head cover shows the parts relevant for adjustment of the camshaft.Oil dipstickTool mounting for adjustment of camshaftS474_320Hall sensor G40 Temperature sensor G62Further information about this engine can be found in self-study programme no. 296 "The 1.4 ltr. and 1.6 ltr. FSI engine with timing chain".27 EnginesSystem overview of Magneti Marelli 7GV engine managementG28 Engine speed senderG40 Hall senderF F47 F36Brake light switch Brake pedal switch Clutch pedal switchT16 Diagnostic connectionG61Knock sensor 1G62 Coolant temperature senderG79 Accelerator position sender G185 Accelerator position sender 2 G130 Lambda probe after catalytic converter G83 Coolant temperature sender at radiator outletJ623 Engine control unitJ104 ABS control unitJ519 Onboard supply control unitG39 Lambda probeG187, G188 Angle sender 1 and 2 for throttle valve drive on drive-by-wire systemG42 Intake air temperature sender G71 Intake manifold pressure sender K Dash panel insert J285 Control unit in dash panel insertG65 High-pressure sender28 J643 Fuel supply relayJ17 G6Fuel pump relay and Fuel system pressurisation pumpN30-N33Injectors for cylinders 1-4N70, N127, N291, N292 Ignition coils 1-4 with output stageJ338 Throttle valve moduleJ317 Terminal 30 voltage supply relayN80 Activated charcoal filter solenoid valve 1 K132 Fault lamp for electric throttle J293 Radiator fan control unitK83 Exhaust gas warning lampS474_138Z19Lambda probe heater29 Power transmissionThe 5-speed manual gearbox 02TThis gearbox offers the following features:● ● ● ●Only installed with petrol engine in Vento Low weight CO2-optimised gear ratios Torque capacity up to 170NmS474_301The 5-speed manual gearbox 02RThis gearbox offers the following features:●● ● ●Due to higher torque capacity, only for diesel engines Further development of 02J gearbox CO2-optimised gear ratios Torque capacity up to 250NmS474_02730 The 6-speed automatic gearbox 09GThe 6-speed automatic gearbox 09G is a compact, light, electronically controlled gearbox for transverse mounting. This gearbox offers the following features:● ● ● ● ●●Only installed with petrol engine in Vento Max. torque 280Nm Weighs 82kg Measures approx. 350mm Torque converter with torque converter lock-up clutch Automatic and Tiptronic modesS474_028The six forwards gears and reverse are implemented via the arrangement of a simple planetary gear set with a downstream double planetary gear set.S474_033Technical dataWeight Torque Clutch Operating mode Oil volumes approx. 82kg FWD max. 280Nm Torque converter Automatic and Tiptronic 7.0 litres G052025 A2 LifetimeFor more detailed information on the 6-speed automatic gearbox, please refer to self-study programme no. 309 "6-speed automatic gearbox 09G/09K/09M".31 Running gearOverviewThe chassis of the new Vento is the same as that of the Polo 2011. It has McPherson struts on the front axle and a torsion beam on the rear axle. The vehicle sits 15mm higher.VentoS474_071The running gear is characterised by the following features:● ● ● ● ● ●Toe and camber angle engineered (no setting necessary) Front floating caliper brake Ø256mm with fully bolted caliper 14" steel rims (as standard), 15" alloys (optional) Electro-mechanical power steering (C-EPS) Self-adjusting rear Simplex drum brakes Ø 228mm ABS, from Highline equipment versionFurther information about the running gear can be found in self-study programme no. 447 "The Polo 2011"32 The front axleThe front axle is a McPherson strut axle. The ride height has been increased by 15mm as on the Polo 2011. The front axle has a large castor angle-which provides a strong true running character.S474_063The rear axleThe rear axle is a torsion beam axle with V-profile. The ride height, as with the front axle, has been increased by 15mm. Grooved ball bearings are fitted as wheel bearings.S474_06133 Running gearThe wheels and tyres14" steel rim with wheel trim Illustration 15" alloy wheelS474_080 Description Tyre dimension 5Jx14 ET35 175/70 R14 6Jx15 ET40 185/60 R15, 195/55 R15S474_082The braking systemThe braking system is a hydraulic dual circuit system. Vehicles without ABS are equipped with a pressure limiter, which adapts the braking force to the rear axle. The brake light sensor is integrated in the brake master cylinder.Front wheel brakesThe front axle of the Vento is fitted with vented disc brakes with a brake disc size of Ø256x22mm. The front brakes are 3rd generation single-piston floating caliper brakes. The brakes also feature an integrated swivel bearing.S474_05134 Rear wheel brakesOn the rear axle, the Vento has self-adjusting Simplex drum brakes. Dimension: Ø200x40mm. The wheel brake cylinders have a piston diameter of 17.46mm.Before removing the drum brakes, they have to be reset. This is carried out in accordance with ElsaPro via the wheel stud opening through the brake drum.S474_0538.5" brake servoThe Vento is fitted with an 8.5" brake servo. It has a brake master cylinder with integrated brake light sensor that works on the Hall principle.S474_078Brake light sensorS474_13435 Running gearBosch 8.2 brake system with ABSInstalled in the new Vento on the Highline version is a Bosch 8.2 generation traction control system. The brake servo with brake master cylinder is installed in a separate place from the ABS hydraulic unit. The essential features of this system are:● ● ●● ●Smaller component dimensions Reduced weight Emergency hazard warning flashing on braking force greater than 7m/s² ABS on Highline equipment version Pressure limiter not includedReturn flow pump Hydraulic unitABS control unit with data bus connectorS474_12436 The electromechanical power steering systemThe servo-assistance of the electromechanical power steering comes from an electric motor on the steering column. The electromechanical power steering system is compatible with each engine/gearbox combination.The steering comprises the following components: Steering wheel Steering column switch Steering column Steering moment sender G269 Worm gear Electromechanical power steering motor V187 Power steering control unit J500 Universal joint shaft Mechanical steering boxSteering column with height and rake adjustment Power steering control unit J500Electromechanical power steering motor V187Steering moment sender G269Universal joint shaftWorm gearMechanical steering box S474_076●●C-EPS = Column Electric Power Steering; Servo-unit positioned in steering chain, gear type (worm gear/shaft). Further information on the electromechanical power steering system can be found in self-study programme no. 447 "The Polo 2011".37 Electrical systemControl unit locations12J446 Parking aid control unitJ255 Climatronic control unit11J387 Door control unit on driver side10 9J387 Door control unit on front passenger side8SB Fuse box Inside vehicle on right under steering columnJ104ABS control unit7 6 5 4 3 2J623 Engine control unitJ525 Power steering control unitJ519Onboard supply control unit1J217Automatic gearbox control unitJ234 Airbag control unitS474_132SAFuse box Right of engine bay on battery38 The networking concepta J255* R* G384* G273* T16 H8* J533 J623 J519 J362 J285 J500 J104* J386 J387J217*J388J389J234J446*S474_054Meaning of the codes G273* G384* H8* J104* J217* J234* J255* J285 J362 J386 J387 J388 J389 J446* J500 J519 J533 J623 R* T16 Interior monitoring sensor Vehicle inclination sender Anti-theft alarm system horn ABS control unit Automatic gearbox control unit Airbag control unit Climatronic control unit Control unit for display in dash panel insert Immobilizer control unit Driver door control unit Front passenger door control unit Rear left door control unit Rear right door control unit Parking aid control unit Power steering control unit Onboard supply control unit Data bus diagnostic interface Engine control unit Radio Diagnosis connectorKey Powertrain CAN data bus (500kBit/s) Convenience CAN data bus (100kBit/s) LIN data bus (19.2kBit/s) CAN data bus line LIN data bus line K-wire Diagnosis CAN data bus (500kBit/s)Optional depending on equipmenta*The data bus diagnostic interface J533 (Gateway) is integrated in the onboard supply control unit J519 and forms the interface for communication of the data bus systems.39 Electrical systemThe dash panel insertThe dash panel insert installed in the Vento is the same as that installed in the Polo 2011. The instrument level has one continual glass surface. This leads to a greater viewing angle. The central display in the dash panel insert is monochrome black and red. For the display, it features exclusively predetermined segments. The dial faces of the speedometer and rev counter are white illuminated.Rev counter with integrated symbol displaysCentral display (multifunction display)Turn signal indicatorS474_036 Setting button for clock Reset button for trip counter Speedometer with integrated symbol display40 Overview of symbols in dash panel insertSymbols in speedometerSymbol Brief explanation Fault in airbag and belt tensioner systemSymbols in central displaySymbol Brief explanation Driving time Warning if stored speed is exceeded by more than 30km/h Icy road warning at below +4°C (+39 °F)Fuel tank almost emptyAt least one door is open or not properly closed Handbrake applied, brake fluid too low or malfunction in braking system ABS malfunction or failureFuel tank almost empty Average consumption Service interval displayFault in electronic accelerator pedal unit S474_106a-r Engine management malfunctionSymbols in rev counter displaySymbol Brief explanation Main beam on or headlight flasher pressed Steering wheel or power steering faultAlternator faultEngine cooling system faultEngine oil pressure too low41 Electrical systemThe electronic immobilizerThe Vento is equipped with an immobilizer of the fourth generation. This is active when the ignition is switched on and prevents unauthorised operation of the vehicle by intervention in the engine control unit.The components of the immobilizerThe immobilizer control unit is integrated in the dashpanel insert. Other components are: Control lamp in dash panel insert Reader coil in ignition lock Programmed ignition key with transponder Engine control unitEngine control unitImmobilizer control unit in dash panel insertReader coil in ignition lockS474_010 Key with transponder42 Features of 4th generation unit●●Rolling code generated and evaluated in engine control unit and immobilizer control unit respectively Online adaption (internet connection) via VAS testerFunctionWhen the ignition is switched on, a permanently stored code is sent to the immobilizer control unit from the transponder. If this code is recognised as valid, a rolling code is generated randomly in the immobilizer control unit. This rolling code is transmitted to the transponder in the vehicle key. An inaccessible computer process now starts in the transponder and the immobilizer control unit. If the result matches, the correct vehicle key is recognised. A rolling code is then checked between the immobilizer control unit and engine control unit. If the process also determines a match, the vehicle is ready for operation. This calculated rolling code cannot be decoded due to the classified computing process. It is therefore generally not possible to duplicate the vehicle key. Instead, a new key has to be programmed in the event of loss or replacement.Programming transponderThe key transponder is programmed just once, whereafter the key is paired with the immobilizer. This is carried out via a corresponding test program with the aid of the VAS tester. The key cannot be programmed to any other immobilizer once this has been done.43 Convenience electronicsCentral lockingA remote central locking system is available for the Vento from the Highline version. This represents enhanced user-friendliness. The central locking with remote control is equipped with two folding key remote fobs. Using the three buttons on the folding key remote fob, the driver can conveniently lock and unlock the car conveniently without the mechanical key. In addition, the boot lid can also be released.S474_308 Lock Open boot lid Release Folding key UnlockDoor control elementsElectric window regulatorsElectric window regulators are installed as standard on all doors. The Vento features the Auto-Down function as standard from the Trendline version. From the Highline version, all window regulators also feature the rollback function and the windows in the rear doors have a child lock. On the Highline version, electric exterior mirrors are also installed.Electric adjustable exterior mirrorCentral lockingBoot lid releaseWindow regulator switchChild safety lock for windows of 2nd seat rowS474_09844 Park Distance Control (PDC)Rear parking aidAn optional parking aid is available for the Vento. This parking aid makes reverse parking easier. Four ultrasound sensors are installed in the bumper area to achieve this. The control unit can be found on the rear left in the boot. The acoustic signaling device is installed in the left C-pillar. The system is active as soon as the ignition is switched on and reverse gear is engaged.S474_066 Steady tone Intermittent toneThe distance warning system starts with an acoustic signal from a distance of 1.60m from an obstacle. The frequency of the acoustic signal changes as the distance to the obstacle diminishes. From a distance of 20cm the acoustic warning is steady.Ultrasound sensorS474_070Control unitAcoustic deviceReverse gear switchS474_06845 RadioThe radio systemInitially, one radio version is available for the Vento.Indian Top Power (RCD 030) radioTechnical features● ● ● ● ● ● ● ●UHV LOW support AM/FM reception CD/MP3/WMA 4 X 20 Watt Self-diagnosis via radio display Monochrome display 112mm x 30mm Display via segments 24 memory slots for AM and FM stations on two memory levels respectively with 6 slots eachS474_114DiagnosisDiagnosis is only possible via the self-diagnosis feature of the radio. This is started by pressing station-memory buttons 1 and 6. For the automatic testing process, station memory button 4 then has to be pressed. Self-diagnosis options Aerial diagnosis: possible displays "OK" or "Fault" USB port connection diagnosis: possible displays "OK" or "Fault" Radio hardware and software version diagnosis Speaker final control test: via the relevant selection, various frequencies are actuated in succession on the different speakers and are visualised accordingly on the display. The mechanic decides whether the speaker is OK by means of an acoustic test.46 The aerial of the VentoIn the Vento 2011, an active rod-type aerial is installed on the roof for radio reception. The amplifier electronics are installed in the base of this aerial.S474_102Radio preparation for radio with single tunerIn the basic version from Trendline, there is at least one radio preparation installed in the Vento. This comprises:●●● ●Power supply wires up to radio installation slot Loudspeakers up to A pillars Aerial wire up to roof aperture One active roof aerial with preamplifierRadio preparationBRCD 030B AM/FMS474_10447 Heating and air conditioningThere are two different air conditioning systems available for the Vento● ●Manual air conditioning in Trendline version Fully automatic Climatronic air conditioning in Highline versionEach version has its own control panel. All temperature and ventilation-relevant controls and the air conditioner control unit are comprised to form one operating unit. The Vento is installed as standard with the manual air conditioning system.The manual air conditioning systemThe manual air conditioner has an internally regulated A/C compressor with a magnetic coupling. The air conditioner is switched on via the air conditioner "AC" button, which is located on the right beneath the four-stage blower switch. The AC button is locked against the blower switch in stage "0". The temperature is adjusted using the left-hand rotary temperature selection knob. The adjustment is transmitted to the heater flap mechanism in the air-conditioner unit via a flexible shaft. A potentiometer is additionally installed on the operating unit to electronically detect the set temperature. The central flap, the footwell and the defroster flap are adjusted via the right-hand rotary air distribution knob by means of a flexible shaft. The fresh and recirculated air flap is actuated via the recirculated air mode button. The flap is adjusted via an electric actuator. The "recirculated air" position is indicated by the feedback LED in the button.Rotary knob for temperature selectionBlower switch Rotary knob for air distributionS474_048 Button for recirculated air mode with feedback LED Button for air conditioner with feedback LEDFurther information about the manual air-conditioner can be found in self-study programme no. 447 "The Polo 2011".48 The fully automatic "Climatronic" air conditionerOn the "Climatronic" air conditioner, all of the functions are controlled fully automatically. In addition to the front vents, the Climatronic features a centre vent for the rear passenger area. The Climatronic has a self-diagnosis function and an internally controlled magnetic coupling.Further information about the heating and air conditioning can be found in self-study programme no. 263 "The Polo 2002".Rotary knob for ON/OFF and fan speedRotary knob for adjusting interior temperatureS474_046 Display for Climatronic status AC buttonFresh air and recirculated air flapsOn the manual air conditioning system, the vehicle's interior is treated as one single climatic zone. The climate control device has a combined fresh air/recirculated air flap that is actuated by a servomotor. The air distribution flaps are actuated by a flexible shaft on the manual air conditioning system. The temperature is adjusted using the rotary knob by adding hot or cold air. On the Climatronic air conditioner, the vehicle's interior is also treated as one single climatic zone. Unlike the manual system, however, the temperature and air distribution flaps are actuated individually by a servomotor. The temperature is adjusted using the rotary knob by adding hot or cold air.49 Heating and air conditioningSystem overview ClimatronicG89 Temperature sensor - fresh air intake duct G261 Outlet temperature sender, left footwell G262 Outlet temperature sender, right footwell G150 Outlet temperature sender, left G151 Outlet temperature sender, rightG65 High-pressure senderG220Servomotor potentiometer for left temperature flap G221 Servomotor potentiometer for right temperature flapG135 Servomotor potentiometer for defroster flap G143 Servomotor potentiometer for recirculated air flap G112 Servomotor potentiometer for central flap G113 Servomotor potentiometer for backpressure flapJ255 Operating unit with Climatronic control unitG263 Outlet temperature sender, evaporatorPowertrain CANJ285 Control unit with display in dash panel insertJ220 Motronic control unit50 V107 Defroster flap servomotorN25 Magnetic coupling for air-conditioning compressorV2S474_052Fresh air blower with integrated blower regulator (on manual air conditioner control system is not electronic but works using series resistors instead).Convenience CANJ533 Data bus diagnostic interface J519 Onboard supply control unit51 474© VOLKSWAGEN AG, Wolfsburg All rights and rights to make technical alterations reserved. 000.2812.46.20 Technical status 08.2010 Volkswagen AG After Sales Qualifizierung Service Training VSQ-1 Brieffach 1995 D-38436 Wolfsburg❀ This paper was manufactured from pulp that was bleached without the use of chlorine.