TECHNICAL DOCUMENTATION
SSP 488 The Passat 2011

This PDF is currently unavailable.
Read document text
Service TrainingSelf-study Programme 488The Passat 2011The Passat 2011In its seventh generation, the new Passat has been perfected in terms of comfort, quality and safety attributes as well as in the range of driver assistance systems offered. Straight lines, clearly structured surfaces and dynamic proportions distinguish the design of the new generation saloon and estate. New experiences in comfort are achieved by the rear seat system that can be released from the luggage compartment, a trailer hitch that folds out at the press of a button, noise insulating laminated safety glass for the windscreen and front side windows and 2nd generation park assist steering system. Highly efficient and eco-friendly TSI engines, TDI CR lightweight engines, a natural gas powered engine and an engine of the newest generation that can be powered with up to 85% ethanol in the vehicle. Engine downsizing, the start-stop system and regenerative braking facilitate a significant saving in fuel consumption during operation. The Front Assist system with automatic City Emergency Brake (braking function) and the Fatigue Detection System are new and progressive functions in the area of safety. With its high level of quality, the new Passat generation bridges a gap to the next highest vehicle category.S488_043S488_045The self-study programme portrays the design and function of new developments. The contents will not be updated.For current testing, adjustment and repair instructions, refer to the relevant service literature.Caution Note2ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Occupant protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19Engines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Power transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37Running gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Driver assist systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44Electrical system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51Convenience electronics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56Radio, navigation and telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58Heating and air conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 683IntroductionThe Passat 2011The overview indicates important series production and optional equipment features of the new Passat. The range of options depends on the equipment lines: Trendline, Comfortline and Highline. Deviations may be possible depending on the country.●● ●Bi-xenon headlights with dynamic light assist and LED day driving lights, optional LED tail lights Main beam assist for halogen headlights, optional● ● ●●Windscreen with acoustic laminated glass Heated windscreen, optional Front side windows with acoustic laminated glass, optional Sliding/tilting electric solar roof, optional*S488_007●●●Luggage compartment lid with automatic opening* Dual clutch gearbox with freewheel function, optional Adaptive chassis control DCC, optional● ● ● ●Adaptive cruise control ACC Front Assist with City Emergency Brake 2nd generation park assist steering, optional Fatigue Detection System*Only saloon4● ● ●"Premium" cellphone preparation, optional Air conditioning system Keyless access inc. start button, optional● ● ●Panoramic sliding roof, optional** Electromechanical parking brake Electric opening and closing rear lid, optional**S488_009● ● ●Head restraints adjustable in X-direction Rear seat backrest with remote release Climate control seat with massage function, optional●● ●Trailer hitch with folding feature and electric release Luggage compartment management, optional** Convenient opening of luggage compartment cover**** Only estate5IntroductionTechnical dataExterior dimensions and weightsThe details for the Passat saloon 2011 and the estate 2011 are based on a vehicle without driver, with standard equipment, 1.4l 90kW TSI engine and 205/55 R16 tyres.S488_029941mm2712mm 4769mm1116mm1552mm 1820mm1470mm1551mmExterior dimensionsPassat saloon Length Width Height Wheelbase Track width at front Track width at rear Turning circle 2006 4765mm 1820mm 1472mm 2710mm 1552mm 1551mm 11.4m 2011 4769mm 1820mm 1470mm 2712mm 1552mm 1551mm 11.4mWeights/further detailsPassat saloon Gross vehicle weight Kerb weight Max. trailer load, braked Max. roof load Tank capacity Drag coefficient 2006 1950kg 1391kg 1300kg 100kg 70litres 0.295cd 2011 1990kg 1365kg 1400kg 100kg 70litres 0.291cd6S488_031941mm2712mm 4771mm1118mm1552mm 1820mm1516mm1551mmExterior dimensionsPassat estate Length Width Height (with roof rails) Wheelbase Track width at front Track width at rear 2006 4774mm 1820mm 1820 1516mm 2710mm 1552mm 1551mm 2011 4771mm mm 1516mm 2712mm 1552mm 1551mmWeights/further detailsPassat estate Gross vehicle weight Kerb weight Max. trailer load, braked Max. roof load Tank capacity Drag coefficient 2006 1950kg 1391kg 1300kg 100kg 70 litres 0.304cd 2011 2070kg 1402kg 1400kg 100kg 70 litres 0.298cd7IntroductionInterior dimensions and volumes1022S488_033 1797mm859mm332mm565litresS488_037729mm1766mm961 mmmm1014mmInterior dimensions and volumesPassat saloon Luggage compartment volume Height of rear lid Height of load sill Cargo area height Width of cargo area/wheel housing 2006 565litres 1756mm 729mm 332mm 1014mm 2011 565litres 1766mm 729mm 332mm 1014mm Passat saloon Interior length Interior length 2nd seat row Front headroom Headroom 2nd seat row Knee room 2nd seat row 2006 1797mm 859mm 1022mm 961mm 91mm 2011 1797mm 859mm 1022mm 961mm 76mm81018 mS488_035 1797mm859mm719mm603litresS488_039624mm2027mm980 m mm1003mmInterior dimensions and volumesPassat estate Luggage compartment volume Height of rear lid Height of load sill Cargo area height Width of cargo area at wheel housing 2006 603litres 624mm 719mm 1000mm 2011 603litres 624mm 719mm 1003mm Passat estate Interior length Interior length 2nd seat row Front headroom Headroom 2nd seat row Knee room 2nd seat row 2006 1797mm 859mm 1018mm 980mm 91mm 2011 1797mm 859mm 1018mm 980mm 76mm2058mm 2027mm9BodyBody structureThe main aim during development of the body was to increase the body strength whilst, at the same time, reducing weight. The bodies of the new Passat saloon and Passat estate are the same as the tried and tested 2006 model series and have been further improved.Scope of modifications to Passat saloon● ● ● ●Bonnet Rear lid Wings Outer skin of doors● ● ●Side panel A-pillar and door frame Rear panelS488_032Key Carried over New10Scope of modifications to Passat estate● ● ● ●Bonnet Rear lid Wings Doors● ● ● ● ●Roof Side panel A-pillar and door frame D-pillar Rear panelS488_03011BodyWindscreen with acoustic laminated glassThe windscreen in the Passat 2011 features acoustic laminated glass as standard. Furthermore, the windows in the front doors are also available as an option with acoustic laminated glass. The use of acoustic PVB in the door windows makes it possible to achieve a noise reduction of approx. 2-4 dB in the interior. Furthermore, a heated windscreen can be ordered for the first time in the Passat in conjunction with heat reflective glass.S488_041Windscreen with acoustic laminated glassOuter glass (2.1mm) Inner glass (1.6mm) S488_036 PVB film (0.33mm) Acoustic PVB film (0.1mm) PVB film (0.33mm)Conventional windscreenOuter glass (2.1mm) Inner glass (1.6mm) S488_034PVB film (0.76mm)Door window (TSG) with acoustic glassOuter glass 1.6mm) Inner glass (1.6mm) PVB film (0.33mm) Acoustic PVB film (0.1mm) PVB film S488_044 (0.33mm)Standard door window (safety glass)Safety glass (3.85mm) S488_038Compared with conventional door windows, there is a change to the software in the door control unit on vehicles with acoustic door windows, and the window retainer in the door is also different. This must be taken account of in the event of retroinstallation and repairs.12The luggage compartmentIn the Passat estate, the following special features should be noted:● ●the additional partition the sliding cargo floorS488_047Cargo floorRemote releaseSliding cargo floor● ● ● ●Variable stowage space Different locking positions possible Removable cargo floor Withstands up to 100kgRemote release of rear seat backrestThe new remote release of the rear seat backrest makes release possible from the luggage compartment. The function is a standard feature from the Trendline equipment level.Cargo floor positionIn the saloon and estate model, the rear bench seat has a 60/40 split folding backrest.13BodyHalogen headlightsOn this headlight module, the dipped beam and main beam are designed as separate H7 headlights. The side light is integrated into the dipped beam headlight. Dynamic light assist is not available for this module. As an option, the main beam assist function is available in conjunction with halogen headlights.Dipped beam, H7 (55W) Side light (5W)Main beam, H7 (55W)Turn signal (24W)S488_013S488_064Light module in bumper In conjunction with H7 headlights, the cornering, fog and day driving lights feature two separate bulbs.Day driving light (21W)Fog and cornering light (H8, 35W)14Xenon headlights with LEDOn this headlight unit, the dipped beam and main beam are integrated into the xenon module (D3S 35W). It features LED daytime running lights and side light. Fifteen individual LEDs are located around the xenon module. The amount of power drawn by the day driving lights is reduced to approx. 30watts compared with approx. 140 to 180watts on daytime headlights with dipped beam activated. The xenon headlight always comes with the dynamic cornering light. Dynamic light assist (DLA) is available as an option. Main beam assist cannot be combined with the xenon headlight.Turn signal (24W)Dipped beam and main beam, xenon (D3S 35W)Daytime runing light and side light (15 LEDs with total 30W)S488_011S488_064Light module in bumper In conjunction with xenon headlights, the cornering and fog lights feature two separate bulbs.Cornering light (35W)Fog light (35W)15BodyTail lightsThe tail lights of the Passat 2011 have a two part design. Only the outer lights are secured by a central bolt.Tail light Brake lightReflector (in trim) Tail lightTurn signal (21W)S488_050 Reflector (in lens) Reversing light (16W) Rear fog light (LED 2.2W)LED tail lightsAccess to the securing screws is on the left and right above the covers in the luggage compartment side panels.Tail and brake light Reflector (in lens)Reflector (in lens)S488_048 Turn signal (21W) Reversing light (16W) Rear fog light (3xLED; 3W total)16Interior equipmentHead restraints with XadjustmentOnce the release mechanism has been activated, the head restraints in the Passat can be adjusted at the base to be further away from or closer to the neck. This helps to achieve an optimal position of the head restraint, which, in addition to comfort, also enhances safety.ReleaseS488_052Stowage facilitiesFrontThere are many multifunctional stowage compartments in he Passat. A centre armrest, which opens to reveal a compartment, is an option in both the saloon and the estate.Storage under AC controls Glove compartment Door compartment S488_068Small glove compartment by steering wheelStorage in centre console with drink/can holderStorage in centre armrest with cellphone charging cradle and compartment beneath17BodyIn rearRear door compartmentStowage pockets on back of front seatsS488_066 Storage compartment in centre armrest Drink/can holder 12 volt connection18Occupant protectionSafety equipmentThe new Passat is equipped as standard with six airbags: Driver and front passenger airbag, side airbags at front and curtain airbags for front and rear passengers. As an option, two side airbags are available for the rear seats. The crash sensors ensure that all airbags trigger safely.Curtain airbagThe curtain airbag of the Passat 2011 ensures the safety of occupants in all seat rows in the head and shoulder area.S488_015Side crash sensor Front doorsSide crash sensor C-pillarSide crash sensorsThe side crash sensors in the bottom area of the front doors are designed as pressure sensors. Lateral acceleration sensors to detect side impact are located in the C-pillar.19EnginesEngine/gearbox combinationsPetrol engine 1.4l 90kW TSI engine with turbocharger 1.4l 110kW TSI engine with dual charging 1.4l 118kW TSI engine with dual charging 1.8l 118kW TSI engine with 4-valve technologyDiesel engineR+S 6-speed manual gearbox MQ200-6F 0AJRRR6-speed manual gearbox MQ250-6F 02S6-speed manual gearbox MQ350-6F 02Q6-speed dual clutch gearbox DQ250-6F 02E7-speed dual clutch gearbox DQ200-7F 0AMR = with regenerative braking; S = with start-stop system (optional equipment)202.0l 155kW TSI engine with 4-valve technology and turbocharger3.6l 220kW FSI engine with 4-valve technology1.6l 77kW TDI CR engine2.0l 103kW TDI CR engine2.0l 125kW TDI CR engineRRR+SR+SR+SMQ350-6F/ADQ250-6ADQ250-6F/AF = front-wheel drive; A = four-wheel drive21Engines1.4l 90kW TSI engine with turbochargerThis engine has found application in other vehicle models and was carried over.Technical features● ● ● ● ● ● ●Homogeneous mode (lambda 1) Turbocharger with wastegate Dual circuit cooling system Air-to-liquid charge air cooling Regulated duo-centric oil pump Demand-based fuel system High pressure fuel pump with integrated pressure limiting valveS488_201Further information on this engine can be found in self-study programme no. 405 "The 1.4l 90kW TSI engine with turbocharger".Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel Exhaust gas treatment CAXA 4-cylinder in-line engine 1390cm3 76.5mm 75.6mm 4 10:1 90kW at 5000 rpm 200Nm at 1500 to 4000 rpm Bosch Motronic MED 17.5.5 Super unleaded RON 95 3-way catalytic converter, broadband lambda probe upstream and regular lambda probe downstream of catalytic converter EU5Torque and power diagram250 225 200 175 Torque [ Nm] 150 125 100 75 50 25 0 1000 3000 5000 Engine speed [rpm] 100 90 80 70 Output [kW] 60 50 40 30 20 10 0 7000 S488_200Emissions standard221.4l 110kW TSI engine with dual charging (EcoFuel)This engine is practically the same as the EcoFuel engine of the Passat 2010. Items changed are the electronic gas pressure regulator and gas inlet valves. Their function has remained the same, however. Technical features●●● ●●●One engine control unit for natural gas and petrol operation Homogeneous mode (Lambda 1) in both operating modes Turbocharger with wastegate Mechanical supercharger that can be activated separately Mechanical pressure reduction stage discontinued on electronic gas pressure regulator Optimised gas inlet valves, thereby making engine start possible from -10 °C in natural gas modeS488_231Further information on this engine can be found in self-study programme no. 359 "The 1.4l TSI engine with dual charging" and no. 425 "EcoFuel natural gas power with 1.4l 110kW TSI engine".Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel CDGA 4-cylinder in-line engine 1390cm3 76.5mm 75.6mm 4 110kW at 5500 rpm 220Nm at 1500 rpm to 4500 rpm Bosch Motronic MED 17.1 Natural gas H (high) Natural gas L (low) with reduced range Super unleaded RON 95 Main catalytic converter, lambda control EU5 10:1Torque and power diagram260 240 220 200 Torque [ Nm] 180 160 140 120 100 80 60 1000 3000 5000 Engine speed [rpm]120 110 100 90 Output [kW] 80 70 60 50 40 30 20 7000 S488_216Exhaust gas treatment Emissions standard23Engines1.4l 118kW TSI engine with dual charging (MultiFuel)This engine was first used as a bioethanol version. First introduced in Sweden and Finland.Technical features● ●● ● ● ● ●●Bioethanol compatible up to 85% Fuel quality sender for detection of bioethanol content in fuel Electric engine preheater in cooling system Cylinder head of 1.4l 110kW TSI EcoFuel engine Homogeneous mode (lambda 1) Turbocharger with wastegate Mechanical supercharger that can be activated separately High pressure fuel pump with a specially coated pump piston that reduces friction and wearS488_203Further information on this engine can be found in self-study programme no. 359 "The 1.4l TSI engine with dual charging".Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel CKMA 4-cylinder in-line engine 1390cm³ 76.5mm 75.6mm 4 10:1 118kW at 5800 rpm 240Nm at 2000 to 4500 rpm Bosch Motronic MED 17.1 Super unleaded RON 95 Ethanol can be mixed up to 85% (E85) in all conditions 3-way catalytic converter, broadband lambda probe upstream and regular lambda probe downstream of catalytic converter EU5Torque and power diagram280 260 240 220 Torque [ Nm] 200 180 160 140 120 100 80 1000 3000 5000 Engine speed [rpm] 120 110 100 90 Output [kW] 80 70 60 50 40 30 20 7000 S488_202Exhaust gas treatmentEmissions standard241.8l 118kW TSI engine with 4-valve technologyThe 1.8l TSI engine designated EA888 is a technically optimised further development of the familiar 4cylinder EA113 engine series. Tried and tested engine components have been consistently further developed. The engine also finds application in the Golf GTI. Technical features● ● ●●●●Improved pedestrian impact protection Significant improvement in comfort and acoustics Balancer shaft system with two shafts, offset in height and each with three bearings Reduced repair complexity thanks to modified housing of oil filter module Base engine configured for a very broad performance range The turbocharger pressure unit can be exchanged and adjusted.S488_227Further information on this engine can be found in self-study programme no. 401 "The 1.8l 118kW TFSI engine with timing chain".Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel CDAA 4-cylinder in-line engine 1799cm3 82.5mm 84.1mmTorque and power diagram280 260 240 220 Torque [ Nm] 200 180 160 140 120 100 80 1000 3000 5000 120 110 100 90 Output [kW] 80 70 60 50 40 30 20 7000 S488_2264 9.8:1 118kW at 4500 to 6200 rpm 250Nm at 1500 to 4500 rpm Bosch Motronic MED 17.5.2 Super unleaded RON 95 (Normal unleaded RON 91 with marginally reduced performance) Upstream catalytic converter in proximity of engine with upstream broadband probe, main catalytic converter with downstream regular lambda probe EU5Exhaust gas treatmentEngine speed [rpm]Emissions standard25Engines2.0l 155kW TSI engine with 4-valve technology and turbochargerThe 2.0l TSI engine also belongs to the in-line 4cylinder EA888 engine series. It has the same design as the 1.8l TSI engine, but with an increased capacity. Technical features●●The higher displacement is achieved by modified pistons, conrods and crankshaft. The turbocharger pressure unit CANNOT be exchanged and adjusted.S488_229Further information on this engine can be found in self-study programme no. 401 "The 1.8l 118kW TFSI engine with timing chain".Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel CCZB 4-cylinder in-line engine 1984cm3 82.5mm 92.8mmTorque and power diagram340 320 300 280 Torque [ Nm] 260 240 220 200 180 160 140 1000 3000 5000 Engine speed [rpm] 200 180 160 140 Output [kW] 120 100 80 60 40 20 0 7000 S488_2284 9.6:1 155kW at 5300 to 6200 rpm 280Nm at 1700 to 5200 rpm Bosch Motronic MED 17.5.2 Super unleaded RON 95 (Normal unleaded RON 91 with marginally reduced performance) Upstream catalytic converter in proximity of engine with upstream broadband probe, main catalytic converter with downstream regular lambda probe EU5Exhaust gas treatmentEmissions standard263.6l 220kW FSI engine with 4-valve technologyThe 3.6l 220kW FSI engine with 4-valve technology is a constituent of the VR engine series. Numerous consumption-optimising measures have been performed on the engine. Technical features●● ●● ●●Oil pump output reduced and oil pressure lowered to 3.6 bar Non-engaged chain tensioner 89° opening temperature of coolant thermostat One-part oil pump chain sprocket Exhaust camshaft adjuster with 32° setting range Vibration damper secured with 7 boltsS488_233Further information on this engine can be found in self-study programme no. 360 "The 3.2l and 3.6l FSI engine"Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel BWS 6-cylinder in-line engine 3597cm3 89mm 96.4mmTorque and power diagram400 380 360 340 Torque [ Nm] 320 300 280 260 240 220 200 1000 3000 5000 240 220 200 180 Output [kW] 160 140 120 100 80 60 40 7000 S488_2304 11.4:1 220kW at 6600 rpm 350Nm at 2400 to 5300 rpm Bosch Motronic MED 17.1 Highest grade unleaded with RON 98 (Super unleaded RON 95with marginally reduced performance) Three-way catalytic converter with lambda control EU5Exhaust gas treatment Emissions standardEngine speed [rpm]27EnginesNew features of 3.6l 220kW FSI engineTo reduce fuel consumption and the emission of CO2, several consumption optimising features were performed on the engine. In addition, further innovative developments were implemented in the design of the engine.Duo-centric oil pumpThe entire oil circuit of the engine was improved and the output of the oil pump consequently reduced. In doing so, it was possible to lower the opening oil pressure from 5.7bar to 3.6bar.Gasket Seal 2nd half of housing Outer rotor 1st half of housing Bearing bush Radial shaft sealS488_026Inner rotor Spring Control plunger Drive shaft PlugVibration damperTo ensure secure attachment, the vibration damper is secured with 7 bolts, as on the Passat R36 (previously one centre bolt).Bolt attachment Vibration damperS488_23428Chain tensionerThe lower chain tensioner has been optimised in terms of leaks and works without engagement at a lower oil flow rate (originally 0.86l/min, now 0.04l/min). Without a locking mechanism it was possible to reduce the chain forces. The spring serves to pretension the chain during cold starting. The ram serves purely to fill the void in the hollow control plunger and thereby facilitates faster response from the chain tensioner when oil pressure is building up.Chain tensioner module Housing Choke boreGuide rail Control plunger RamS488_036 Pretensioning springS488_038The choke bore must not be punched through or cleaned using any kind of tool.Chain sprocketMarking for primary chain driveThe oil pump chain sprocket has a one-piece design to prevent incorrect fitment.S488_060Marking for camshaft timing chain drive29EnginesCamshaft adjusterThe exhaust camshaft adjuster only works in a 32° range of crankshaft adjustment. At idle, less exhaust gas flows back into the inlet port, which means residual gas compression no longer occurs. Engine running is thus smoother and consumption at idling speed is reduced by about 3-5%Range of adjustment 32°Camshaft adjusterS488_028Camshaft adjuster coverLocated between the camshaft adjuster cover and the cylinder head is a seal. The seal optimises oil supply to the camshaft adjuster, which in turn raises its adjustment speed.Cover for camshaft adjuster SealS488_239301.6l 77kW TDI CR engineThe 1.6l TDI CR engine, already tried and tested in the Polo 2010, was further developed for use in the P assat 2011.Technical features● ●●●●Common rail injection system with piezo injectors. EGR module with exhaust gas recirculation valve and exhaust gas recirculation cooler. Plastic intake manifold without swirl plate adjustment Spur gear drive for camshafts without tooth backlash compensation Fuel high pressure pump without sprocket for pressurisation pumpS488_205The design and function of the 1.6l TDI CR engine is described in self-study programme no. 442 "The 1.6l 77kW TDI engine with common rail injection system".Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Maximum output Maximum torque Engine management Fuel Exhaust gas treatment Emissions standard CAYC 4-cylinder in-line engine 1598cm3 79.5mm 80.5mm 4Torque and power diagram280 260 240 220 Torque [ Nm] 200 180 160 140 120 100 0 1000 3000 5000 Engine speed [rpm] 100 90 80 70 Output [kW] S488_204 60 50 40 30 20 10 1016.5:1 77kW at 4400 rpm 250Nm at 1500-2500 rpm Simos PCR2.1 Diesel complying with DIN EN590 Exhaust gas recirculation, oxidising catalytic converter and diesel particulate filter EU531Engines2.0l 103/125kW TDI CR engineSecond generation 2.0l TDI CR engines are used in the Passat 2011. These engines are a further development of the 2.0l TDI CR engine from the 1st generation, tried and tested in many Volkswagen models since 2007. The engine is offered with two performance levels.S488_207Features of 2nd generation 2.0l TDI CR engine Common rail fuel injection system with solenoid valve controlled injectorsS488_206Cylinder head as on 1.6l TDI CR engine with portion of channel for recirculated gas running through cylinder headS488_211Exhaust gas recirculation module as on 1.6l TDI CR engine with EGR valve and exhaust gas recirculation cooler.S488_209Plastic intake manifold without swirl plate adjustmentS488_21332Technical dataOutput Engine code Type Displacement 19 Bore 8 Stroke 95 Valves per cylinder Compression ratio Maximum output Maximum torque 103kW at 4200 rpm 320Nm at 1750 to 2500 rpm 103kW CFFB 68cm3 1mm .5mm 4 16.0:1 125kW at 4200 rpm 350Nm at 1750 to 2500 rpm 125kW CFGBTorque and power diagramNm 360 340 320 300 280 260 240 220 200 180 160 1000 2000 3000 4000 kW 120 110 100 90 80 70 60 50 40 30 20 50004-cylinder in-line engineEngine management Fuel Exhaust gas treatmentBosch EDC 17 (common rail injection system) Diesel complying with DIN EN 590 Exhaust gas recirculation, oxidising catalytic converter, diesel particulate filter EU5rpmS488_208Output [kW] - 125kW Torque [Nm] - 1 25kW Output [kW] - 103kW Torque [ Nm] - 1 03kWEmissions standard●Detailed information about the 2.0l TDI CR engine can be found in self-study programme no. 403 "The 2.0l TDI engine with common rail injection system". The design and function of the 1.6l TDI CR engine is described in self-study programme no. 442 "The 1.6l TDI engine with common rail injection system". Further information about the solenoid valve controlled injectors can be found in self-study programme no. 445 "The Sharan 2011". In combination with the 2.0l 103kW TDI CR engine, the Passat 2011 can also be equipped with the "Selective Catalytic Reduction" (SCR) exhaust gas treatment system as a Blue TDI version. The SCR system serves as a means of reducing nitrogen oxide emissions and is described in detail in self-study programme no. 424 "The exhaust gas treatment system: Selective catalytic reduction".●●●33EnginesFuel system for TDI enginesThe overview shown represents the fuel system of the 2.0l TDI engine.1 - Fuel system pressurisation pump G6 The fuel pump builds up pressure in the fuel supply line. 82 - Fuel filter The fuel filter keeps impurities in the diesel fuel away from the components of the injection system. The high precision components, for example, the high pressure pump and the injectors, can be damaged or their function impaired by even the most minute particles of dirt.353 - Fuel temperature sender G81 The fuel temperature sender measures the current fuel temperature. 44 - High pressure pump The high pressure pump generates the fuel high pressure required for injection. 2 5 - Fuel metering valve N290 The fuel metering valve regulates the quantity of fuel needed to generate the high pressure as required.34766 - Fuel pressure regulating valve N276 The fuel pressure regulating valve sets the fuel pressure in the high pressure range.7 - High pressure accumulator (rail) The high pressure accumulator keeps the fuel required for injection under high pressure for all cylinders.98 - Fuel pressure sender G247 10 10 10 10 The fuel pressure sender determines the current fuel pressure in the high pressure range.9 - Pressure retention valve The pressure retention valve ensures that pressure remains constant in the return flow to the injectors. In this way fluctuations in pressure are avoided, thereby making precise control of the injectors possible.10 - Injectors N30, N31, N32, N33S488_2201The injectors inject fuel into the combustion chambers.Colour coding/keyHigh pressure Supply pressure Return pressure from injectors Return pressure35EnginesFuel system pressurisation pump G6In the fuel system of the 1.6l TDI CR engine and the 2.0l TDI CR engines, the fuel system pressurisation pump generates the fuel pressure required for the low pressure system in the fuel tank. As a consequence, the gear-type pump used in the high pressure pump of the previous model in the fuel system of the 1.6l TDI CR engine is no longer required. Likewise, the electric pressurisation pump in the supply line of the low pressure fuel system of the 2.0 l TDI CR engine has been discontinued. The fuel system pressurisation pump in the Passat 2011 is an electrically driven internal gear pump. It is located in the fuel delivery unit GX1. In the fuel pressurisation system for diesel engines, the pump generates a pressure of approx. 6bar. This ensures that the high pressure pump is supplied with sufficient fuel in all operating conditions. A valve in the high pressure pump reduces the fuel pressure generated by the fuel system pressurisation pump in the fuel supply line to approx. 5 bar. This maintains a constant level of pressure in the fuel supply line. The fuel pump is activated by the engine control unit via a relay when the engine is started.Design of fuel delivery unit GX1Fuel line for auxiliary heater Fuel returnFuel supplyElectrical connectionFuel system pressurisation pump G6S488_215Effects in event of failure The engine will not run if the fuel system pressurisation pump fails.36Power transmissionDual clutch gearbox with freewheel functionSteady consumptionOverrun cut-offSpeed [km/h]CoastingOverrun cut-offDistance [m]Dual clutch gearbox without freewheel function Dual clutch gearbox with freewheel functionS488_240The 6-speed dual clutch gearbox 02E and the 7-speed dual clutch gearbox 0AM can be ordered for the the new Passat with a freewheel function. The role of the freewheel function is to isolate the engine from the gearbox at overrun. This is made possible by opening the dual clutch. The engine turns at idling speed and the vehicle coasts without any engine braking effect. With the freewheel function and by driving with foresight, fuel can be saved. The freewheel function is only possible with the selector lever in the "D" position. If the selector lever is in the "S" position or in the tiptronic gate, or if the driver presses the brake, the freewheel function is suppressed. Not until the engine is placed under load again is the freewheel function reactivated.On dual clutch gearboxes with freewheel function, the gear shift points with the selector lever in "S" are only marginally higher than those in the "D" position.37Power transmissionOverview of gearboxesManual gearboxGearbox type 6-speed manual gearbox MQ200-6F 0AJ Technical features Further development of 0AG gearbox Adapted for 1.4l 90kW TSI engine, gap between pinion shaft and differential increased, sheet metal bearing support replaced by cast metal bearing support for higher torque, teeth ground Final drive uprated Without speedometer sender CO2-optimised gear ratios Torque capacity up to 200Nm Further information SSP 237 SSP 306● ●● ● ● ●6-speed manual gearbox MQ250-6F 02S● ●● ● ●Further development from 0A4 Longer shafts with additional bearings, additional gear pair, new longer housing lid made from aluminium Without speedometer sender CO2-optimised gear ratios Torque capacity up to 250NmSSP 99 SSP 3066-speed manual gearbox MQ350-6F 02Q● ●● ●Further development of 02M gearbox Changes to selector shaft, selector forks with stops in housing, modified bearings Without speedometer sender Torque capacity up to 350NmSSP 205 SSP 30638Dual clutch gearboxGearbox type 6-speed dual clutch gearbox DQ250-6F DSG 02E Technical features The 6-speed dual clutch gearbox 02E is equipped with a hydraulic dual clutch. It combines the high level of efficiency as well as sturdiness and sportiness of a manual gearbox with the high level of comfort of an automatic gearbox during gear changes. Further information SSP 3087-speed dual clutch gearbox DQ200-7F 0AMThe 7-speed dual clutch gearbox 0AM is a further development of the 6-speed dual clutch gearbox 02E. Unlike the 02E, it works with a dry-plate dual clutch and separate oil circuits for the gearbox and mechatronics. Another difference to the 02E is that the electric oil pump for the hydraulics is only actuated by the control unit when required. Actuation occurs once hydraulic pressure in the mechatronics drops below a certain value, necessitating an increase in pressure again in order to assure operability of the mechatronics.SSP 39039Running gearOverviewThe Passat 2011 offers the highest level of driving comfort thanks to its running gear configuration. The running gear is based in essence on the tried and tested running gear of the Passat 2006. Sporty and standard running gear versions are available, as well as adaptive chassis control DCC.●Extended EDL (XDS)●Lightweight McPherson strut front suspension●Parallel axis power steering (APA)●ESP/ABS TRW 450M●Tyre pressure monitoring TPM with auto location Adaptive chassis control DCC, optional●●●Further details about the power steering system can be found in self-study programme no. 399 "The electromechanical steering with parallel axis drive". For further details about the adaptive chassis control, see self-study programme no. 406 "The adaptive chassis control DCC".40●AUTO HOLD function●Electromechanical parking brake●Four-link rear suspensionS488_027●Auto leveling on rear axle, optional●Fatigue Detection System (FDS)●ContiSeal tyres from 17" rims●●Further details about the self-leveling system can be found in self-study programme no. 357 "The Nivomat". Further details about the parking brake can be found in self-study programme no. 346 "The electromechanical parking brake".41Running gearExtended EDL (XDS)The Volkswagen Passat 2011 is equipped with the ESP extension XDS on vehicles with diesel engines from 125kW and on vehicles with petrol engines from 220kW. XDS keeps the wheel on the inside of the corner within the slip limit during fast cornering. Up to a defined torque level, XDS decelerates the wheel on the inside of the corner, thus enabling any increase in torque at the vertex to be offset against the wheel on the outside of the corner. This feature only works if the vehicle is accelerated in the corner and sufficient torque is available. The effect is greater in tight bends in 2nd or 3rdgear and at higher road speeds than in bends with larger radii.Key: with XDS without XDS S488_074With XDS● ● ●Without XDS● ●● ●Better traction Greater agility Follows line of drive better due to less steering angle requirement Reduced tendency to understeer Greater speed out of corners possibleTorque at wheels cannot be increased TCS/EDL/engine torque interventionXDS already finds application in the Golf 6 GTI/GTD and Polo 5 GTI.42Tyre pressure monitoring TPM with auto locationA new, direct measuring tyre pressure monitoring system is employed in the Passat. As before, the system uses sensors in the tyre that report the inflation pressure to the control unit in the vehicle. With the "auto location" feature, the system is capable of clearly identifying and displaying any tyre affected by pressure loss. Furthermore, there is an option of displaying the inflation pressures of all tyres in the dash panel display. The "intelligent aerial" is a combination of TPM auto location control unit and central reception aerial. It is connected to the onboard supply via the extended CAN. Term.15, the speed signal and the reversing signal serve as input parameters. The "intelligent aerial" can be found on the outside of the body in the rear (vicinity of spare wheel well) in a place where reception is favourable.S488_078 S488_080Vehicle statusExample of display in dash panel insertTPM auto location control unit with central reception aerial Dash panel insert with controls Wheel electronics with detection of rotational directionKey: Reception with high level (rear) Reception with low level (front)Once the vehicle is in motion, the electronics in each wheel start sending data telegrams. Some of the information these data telegrams contain is as follows:● ● ● ●ID (identification) Pressure Temperature Direction of rotationWith the direction of rotation data, it is possible even after a short time of driving for each set of electronics to be allocated to the individual wheels. In line with this, the front and rear are identified by a level assessment (which is why the reception aerial is positioned on the rear bumper). This makes it possible to clearly identify the location of every set of wheel electronics.43Driver assist systemsFatigue Detection System (FDS)Driver fatigue is detected by monitoring the steering behaviour. The system meets the following criteria:● ● ● ●Driver alert when fatigue is detected Fatigue monitoring only on motorways, dual carriageways and wide A roads Does not become operable until above 65km/h No imminent warning in event of microsleepFunction and displayThe system stores a reference map in the gateway control unit based on the steering behaviour during the first 15 minutes of driving. A comparison of the driver's current steering response with this reference map is carried out and evaluated. An alert is issued no earlier than 15 minutes of continual driving.Displays in dash panel insert (example of German versions)S488_138S488_136 "Lowline" "Highline"S488_076 "Premium"The function analyses the driver's behaviour while driving the vehicle and detects driver fatigue from certain patterns. The function cannot detect fatigue among all drivers as not all drivers demonstrate the same typical steering behaviour. If the behaviour falls into the fatigue category, the driver is alerted for 5 seconds by a message in the dash panel and a gong. If the driver fails to take a break within the next 15 minutes, the message and gong are repeated. No further message is given once it has been repeated. When the ignition is switched off, the reference map is cleared.44Adaptive Cruise Control (ACC)Adaptive Cruise Control (ACC) regulates the speed and the distance of the vehicle in relation to the traffic ahead at a value predetermined by the driver. In all situations, the driver remains master of the situation in as far as the system can be switched off or the intervention can be interrupted at any time by pressing the brake or accelerator pedal. The Front Assist feature integrated in the ACC helps as an "alert co-driver" to avoid any collision with moving traffic – remaining alert even when the ACC is switched off. The new City Emergency Brake function also reacts to parked vehicles at speeds below 30km/h. In the event of danger, it initiates a brake manoeuvre and can thereby help to avoid an imminent collision or reduce the amount of damage caused as a result.Terminology for driver assist systemsName ACC (Adaptive Cruise Control) Front Assist Formerly known as ADC Short description of function Maintains specific distance in relation to vehicle travelling ahead and adapts speed dynamically to traffic flow.Front ScanConditions vehicle, alerts driver to hazardous situations and improves driving dynamics during overtaking manoeuvres. Reacts to moving vehicles only at speeds greater than 30km/h. Co-function of front assist. Automatically brakes the vehicle prior to a collision. Reacts to moving and stationary vehicles at speeds less than 30km/h.City Emergency BrakeN/ABrake interventions avoid accidents only in exceptional circumstances.FunctionIf the road ahead is clear, ACC moderately accelerates the vehicle up to the desired (set) speed. If a vehicle travelling ahead in the same lane is moving more slowly, the system brakes so that the vehicle ahead can be followed comfortably.S488_09045Driver assist systemsOptimised lane change functionWhen the turn signal is activated, the system detects an intention to overtake and improves the dynamics while taking safe distances into account. Veering out If, with the ACC active, the Passat approaches a vehicle travelling ahead, all that is required is for the turn signal to be activated and the Passat will accelerate up to the set speed when veering out. In this way, the vehicle can be overtaken comfortably. ACC helps to maintain the safe distance automatically.Example (80km/h set)1) Appr oaching a slower vehicle. Speed adapted to target.2) Driver indicates and veers out: system accelerates automatically to 80km/h.S488_122Veering in If the driver activates the turn signal after the vehicle has been overtaken, the road speed is reduced back to the value set in the ACC.3) Driv er indicates.4) Driver veers in: automatic follow-on with ACC set to 80km/h.S488_124Go TriggerIn combination with a DSG gearbox, the vehicle can be brought to a halt when following traffic (follow to stop). A safe distance is taken into account in this case. As soon as the vehicle travelling ahead gains distance and the driver briefly presses the accelerator, the ACC takes up its control function again immediately (Go Trigger).Vehicle brought to halt within safe distanceGo TriggerS488_126S488_12846Front AssistGeneral descriptionFront Assist aids as an "alert co-driver" in certain situations to avoid collisions with traffic - even with the ACC switched off. The new Front Assist is now capable of considerably more. In a manner of speaking it is an "alert codriver with its own brake pedal". Even before the situation reaches a critical point, measures are taken unbeknown to the driver. The aim of Front Assist is to minimise the stopping distance in critical situations.Interplay of ACC and Front AssistThe ACC and Front Assist functions are housed in one control unit, although they are two separate components. Front Assist works independently of the ACC status. It also remains active when the driver switches off the ACC. Decisive for the functional readiness of Front Assist is the display of the status LEDs.LED green:Front Assist switched on and ready to intervene.LED yellow: Front Assist switched on but function sometimes impaired e.g. blocked sensor, overheated brakes, etc.LED off:Front Assist switched off or malfunction.S488_082Caution!Front Assist does not intervene until just before a collision! Interventions avoid accidents only in exceptional circumstances.47Driver assist systemsOverview of Front Assist co-functions1. Vehicle conditioning Vehicle conditioning works in a speed range of 5km/h to 210km/h. The vehicle is prepared for the driver to perform an emergency stop:● ●Prefill function (brake pads against brake discs). Hydraulic brake assist (HBA) trigger threshold adapted to highest sensitivity.2. Driver alert The driver alert is issued in a speed range from 30km/h to 210km/h. The driver is alerted in two stages:● ●Preliminary warning: Warning sound and warning symbol in multifunction display. Main warning: Warning jolt.3. Active brake interventions Active brake interventions take place in a speed range from 5km/h to 210km/h. There are two types of operation:● ●Target braking (braking pressure imparted by driver is boosted). Automatic partial braking (APB) in cases where the driver fails to react.In a speed range from 5km/h to 30km/h, automatic partial braking is also referred to as the "City Emergency Brake" function.City Emergency BrakeIn a speed range from 5km/h to 30km/h, automatic partial braking carries the name "City Emergency Brake". The main difference compared with braking at speeds above 30km/h is that the city brake also reacts to stationary vehicles. Furthermore, in the event of an immediate risk of collision there is no warning jolt, nor is the vehicle decelerated (APB pilot stage). If a collision cannot be avoided, the vehicle is decelerated at a rate of 6.0m/s2.48Overview of Front Assist and City Emergency BrakeThe following graph shows the sequence if a risk of collision is detected and the driver shows no reaction.Risk of collision: Marginal Raised HighestCollisionS488_084HBA sensitiveWarning joltAPB pilot stageAPB main stageHBA = Hydraulic Brake Assist; APB = Automatic Partial BrakingMarginal risk of collision Front Assist Speed of obstacle greater than 30km/h Optical and acoustic warning signal, HBA changeover, braking system prefilled HBA changeover, braking system prefilledRaised risk of collision Warning jolt and APB pilot stage (Brake deceleration 1m/s2)Highest risk of collision APB main stage (Brake deceleration 3.5m/s2)City Emergency Brake Speed of obstacle less than 30km/h-APB ain stage (Brake deceleration 6.0m/s2)mIf the driver intervenes by braking every time there is a risk of collision, the system supports him/her by boosting the brake pressure. In doing so, the system attempts to keep any potential accident damage as minimal as possible.49Driver assist systemsPark assist steering 2.0The new park assist steering 2.0 represents a marked improvement over the previous park assist steering 1.0 and also park assist steering 1.5. With this new semi-automatic parking system, parking in bays perpendicular to the road is made possible and parking in even tighter parking spaces parallel to the road (kerb-side parking) has been made much easier. It is now possible, for example, to park fully or partly on kerbs, park between trees and other obstacles and park on bends.S488_092It is still possible to drive out of kerb-side parking spaces with this system and the process of entering or exiting can be done in several stages. As the first parking system of its kind, park assist steering 2.0 includes active braking support.Further information about this new parking system can be found in self-study programme no. 494 "Park assist steering 2.0".50Electrical systemOverviewThe Passat 2011 is equipped with state-of-the-art technology.S488_051●KESSY with separate ignition and engine start button●Main beam assist●Multifunction camera, optional●Dynamic light assist, optional 2nd generation park assist steering, optional●Lane departure warning with steering intervention●Control unit for terminal and engine start control J942 Heated windscreen, optional●●51Electrical systemSystem overviewThe lane departure warning system, previously used in the Phaeton and Touareg, is now utilised in the Passat 2011. Also finding application in the VW brand are the new light assist systems 'dynamic light assist' (DLA) and 'main beam assist'. The following diagram shows the largest possible network, with the Passat fully equipped.Key Powertrain CAN data bus Convenience CAN data bus Infotainment CAN data bus Extended CAN data bus LIN data bus CAN data bus line LIN d k * data bus line - CAN diagnosis - CAN dash insert - or (not both) J394 Y k J533 J245 Private bus J364 J772 R78 J412 J525 R/J503 R215 d T16J810 J301 J764 J453 J393/J362 J527 J255 J605 J519 J345 J386 J387 J501J285 G397 J400 J926 J92752Key CX1 E313 G397J104 J234 J245 J250J255 J285 J301 J345 J362 J364 J367 J386 J387 J393 J394 J400J412 J428 J446 J453 J492 J500J501 J502J503 J519 J525 J527 J533 J540 J605 J623 J667 J668 J743 J745 J764 J772 J791 J810 J844 J926 J927 R78 R215 R242T16 Y Alternator Selector lever Rain and light sensor ABS control unit Airbag control unit Sliding sunroof control unit Electronically controlled damping control unit Climatronic control unit Control unit in dash panel insert Air conditioning system control unit Trailer detector control unit Immobilizer control unit Auxiliary heater control unit Battery monitor control unit Driver door control unit Front passenger door control unit Convenience system central control unit Roof roller blind control unit Wiper motor control unit Mobile telephone operating electronics control unit Control unit for adaptive cruise control Parking aid control unit Multifunction steering wheel control unit Four-wheel drive control unit Power steering control unit Multifunction unit control unit Tyre pressure monitor control unit Control unit with display for radio and navigation system Onboard supply control unit Digital sound package control unit Steering column electronics control unit Data bus diagnosis interface (gateway) Control unit for electromechanical parking brake Rear lid control unit Engine control unit Power output module for left headlight Power output module for right headlight Mechatronic unit for direct shift gearbox Cornering light and headlight range control unit Electronic steering column lock control unit Reversing camera system control unit Control unit for park assist steering Driver seat adjustment control unit Main beam assist control unit (except with R242 and J745) Rear door control unit, driver side Rear door control unit, front passenger side TV tuner Interface for external multimedia devices Front camera for driver assist systems (except with J844) 16-pin connector Analogue clockJ540J500 J623 J234 E313 J250J104 J743 J791/J446* J492 J844CX1 J367J428 J502R242 J745J667J668 S488_01053Electrical systemThe control unit for terminal and engine start controlFor the first time, a terminal control unit finds application in the new Passat. It serves on one hand to actuate the terminals in advance as a link between the onboard supply control unit and the control elements of the electronic ignition lock. On the other hand, it serves to emulate the terminals for the newly added ignition starter button (ISB). The terminal control unit is only installed in conjunction with KESSY.The terminal control unit can be found in a separate housing holder above the pedal bracket in the driver's footwell. The terminal control unit has a discrete connection to the onboard supply control unit. The control unit is permanently coded for automatic start (pin coding). For the Passat, provision has been made for two functions: with and without start/stop system.S488_132DiagnosisIf the terminal control unit should fail while the vehicle is in motion, terminal 15 will continue to be supplied as an emergency running measure until engine speed is zero. Thereafter, ignition is switched off and emergency running is activated both on the hardware and software side (internal terminal CU measure). This means that the terminal request from the electronic ignition lock is enabled, thereby allowing the vehicle to be operated through this switch. The ISB will no longer work and its light is switched off as with all other implausible ignition starter button problems. The engine control unit interrogates the existing potential for plausibility just before the terminal 50 request from the terminal control unit via the diagnosis wire (terminal 50 R for "read back") for starter actuation. In the event of implausibility, the engine ECU ceases its attempt to start the engine. The onboard supply control unit (OSCU) receives this information at the same time. Both input pins of the ISB must have the same signal so that the operational request from the ISB is accepted by the terminal control unit. Inputs open means ISB not pressed; inputs to earth means ISB pressed. In addition to the information (no fault present; all conditions met for starting), diagnoses are also transported via the path "fault information" from terminal CU to OSCU (2 of 3 status lines currently in use). There are currently two possible fault messages: "Control unit faulty" and "ISB faulty".54FunctionThe driver can control the vehicle functions at the same time from the electric ignition lock or/and from the ignition starter button. Terminals S, 15 and 50 from the electric ignition lock are just passed through in the terminal CU. Terminals S and 15 are generated electronically by the terminal CU due to the request from the ISB. These carry a steady signal upon active request. The term. 50 request during automatic start represents a 200ms square wave impulse from the terminal CU to the engine control unit, irrespective of how long the ISB is pressed. If the engine control unit has information about the framework conditions, such as the PN signal on automatic vehicles (selector lever in P or N position) and the brake signal, the engine control unit actuates both its starter relays (SST1, SST2). On vehicles with manual gearbox, the clutch actuation signal (interlock) serves as a condition for input.Functional diagramSMLS J527B BS488_134 CANB 50_SMLS PN/interlock Term.75ESLAs Cs SKs KaEILPCJ519 OSCUAAJ942 terminal CUSTCAN J623 ECUSST1 SST2 Term.50R CISBCodingKc●● ●PN (automatic gearbox), interlock (manual gearbox) Neutral gear sensor (NGS)* Brake signal (BLS, BTS)Key A As B C Cs P terminal 5 1 terminal 15s terminal 0 3 terminal 0 5 terminal 50s terminal P S Ks Ka Kc ST SST * terminal S terminal CU_S (request from J942) terminal CU_15 (request from J942) terminal CU_50 (request from J942) Status lines with fault and status information Start control On vehicles with start/stop system55Convenience electronicsDynamic light assist (DLA)A new generation of dynamic light assist is used in the Passat 2011 in combination with xenon headlights. It works in the same way as the headlights on the Touareg, though differs in its technical makeup due to different manufacturers. The headlight installed in the Passat features a rotating shutter with four shield profiles. In addition, there is a shutter range with variable light shield (masked permanent main beam).HeadlightD3S Power electronicsReflectorMasking area (DLA)S488_094Lens Shutter with shieldsNetworkingJ533J519 J527J745 R242J667 J668 S488_042J285KeyJ519 J527 J533 J285 J667 Onboard supply control unit Steering column electronics control unit Data bus diagnosis interface (gateway) Control unit in dash panel insert Power output module for left headlight J668 - Power output module for right headlight J745 - Cornering light and headlight range control unit R242- Front camera for driver assist systems56Shield positionsMain road light, motorway light, urban light and touring modeThese light cone patterns (from a vehicle for right-hand traffic) are made possible by three different shield profiles on one shutter. Depending on the speed of the vehicle or menu setting, the shutter toggles between the positions for main road, motorway, urban (not including xenon headlight function with masked permanent main beam) and touring mode. In touring mode, there is no main road (dipped beam), motorway and dynamic cornering light. The following light cone patterns are projected against a wall from a distance of approx. 10m (full illumination):Main road light (up to 110km/h)Motorway light (from 110km/h)Urban light (10-45km/h) Touring mode (static)S488_096 Left light cone raised Maximum dipping of light coneMain beam and masking positionThe masking range on the shutter is used in conjunction with a gradual transition to main beam for dynamic light assist. If the system does not detect any vehicles in the dazzle range of the light cone, the shutter is turned to the non-dipped position. The light cone is therefore unmasked. If a vehicle travelling ahead approaches the light cone, the large shield on the shutter is turned into the light cone dynamically. In this way, only the light that could dazzle oncoming traffic or the vehicle travelling ahead is "dipped". The remaining field of light on the left-hand side is swiveled away from oncoming traffic to the left and "dipped" to the maximum range available for the main road setting. The DLA becomes active from 60km/h and remains this way even if the vehicle is slowed down to 55km/h.Main beam (unmasked position)Dynamic range*Maximum "dipped" range*S488_098 Light cones overlap *Left headlight (mirror image on right headlight)57Radio, navigation and telephoneThe radiosTechnical data Display Touch sensitive (touchscreen) AM, FM, TP and RDS reception (basic tuner) AM, FM, TP and RDS reception (diversity tuner) Integrated DAB tuner (digital radio) Integrated disc drive Integrated SD/SDHC memory card reader Media support Audio input interface (AUX-IN) Telephone interface for hands-free device Interface for connecting a reversing camera Loudspeaker output stages 4x20watt output (2 or 4 loudspeakers can be connected) Control of external CD changer Control of external amplifier Connection of external media devices (USB, mini USB, iPod) Speed-dependent volume adjustment Brightness of display light can be regulated independently of interior light in vehicle Self-diagnosis and loudspeaker diagnosis Service test mode Optical parking system (OPS) Air conditioning information For further information, see self-study programmeRCD 210 Monochrome, 122 x 36 pixels ●CD CD and MP3 audio data Can be retrofitted ● (Mono-channel only) ● ● (No MP, WMA3)● ● ● ●no. 404* Discontinued from model year 2012 ** DAB version shown *** EU version without DAB shown58RCD 310** Monochrome, 302 x 45 pixelsRCD 510*** 6.5", 400 x 240 pixels ● ● ● Depending on equipment CD (6-disc changer) ● CD, MP3 and WMA audio files ● ● Depending on equipment ● ● ● (No MP3, WMA)* ● ● ● ● ● ● ● ● no. 417 ● ● ● ● ● ● ● ● no. 423Depending on equipment CD CD, MP3 and WMA audio files ● ●59Radio, navigation and telephoneThe radio-navigation systemsTechnical data Display Touch sensitive (touchscreen) AM, FM, TP and RDS reception (diversity tuner) Integrated DAB tuner (digital radio) Integrated disc drive Integrated SD/SDHC memory card reader Media support Audio input interface (AUX-IN) Telephone preparation support Interface for connecting a reversing camera Loudspeaker output stages 4x20watt output Control of external CD changer Control of external amplifier Connection of external media devices (USB, mini USB, iPod) Can be combined with TV-tuner Speed-dependent volume adjustment Brightness of display light can be regulated independently of interior light in vehicle Self-diagnosis and loudspeaker diagnosis Service test mode Optical parking system (OPS) Air conditioning information Navigation function with map, integrated driving symbols and voice Integrated storage media Navigation data Navigation data update Traffic sign display For further information, see self-study programmeRNS 315 5", 400 x 240 pixels ● ● Optional CD ● CD, MP3 and WMA audio files External and front ●/+Bluetooth internal ● ● ● ● ● ● ● ● ● ● ● ● Flash memory*** (6GB/4GB NAR) Internal memory via SD card** ● no. 493The hard-disc is partitioned: 20GB are available for media data, 10GB are reserved for navigational data. ** The purchased SD card can be used for any navigation unit, though it is only coupled to the specific device once updated and can only be used with this device. *** Can only be used for navigational data.*60RNS 510 6.5", 800 x 480 pixels ● ● DVD ● CD, MP3, WMA audio, DVD formats External ● ● ● ● ● ● ● ● ● ● ● ● ● Hard-disc 30GB* Hard-disc* DVD ● no. 42361Radio, navigation and telephoneThe aerial conceptPassat saloonOn the saloon, all of the aerials are integrated in the rear window. The entire heating wire structure is part of the FM and TV signal aerial system. The signals are separated electronically according to TV1, TV2 and FM1, FM2. The GSM/UMTS and GPS aerials are designed as separate modules and are clipped onto the rear window. The aerial connections all run via the aerial module, which has the corresponding impedance transformer. Depending on the signals required, the aerial module has three mechanical configurations and nine versions (part numbers). The diagram shows the maximum equipment.Auxiliary heater S488_118DK C A I G BGSM/UMTSTV tunerModulesFM2/TV2 AMA GPSDABIGHBKAerial moduleFM1/TV1LeftRightFurther information on this aerial concept can be found in self-study programme no. 342 "Radio systems 2006".62Passat estateOn the estate model, the radio aerials and the aerials for radio remote control (RRC) of the auxiliary heater are integrated in both rear side windows. In addition to this, it features a roof aerial for GPS and/or GSM/UMTS. Depending on the signals required, the impedance transformer is available in different versions. The diagram shows the maximum equipment.Auxiliary heater S488_116 GSM/UMTS, GPS K B G A I C DTV tuner Impedance transformer AM/FM1/TV1 D RRC auxiliary heater AB FM2/TV2FM1/TV1FM2/TV2Left Key: B I A C DG/HAMDABRightFM1/AM FM2 (Diversity) DAB GPS GSM/UMTS TV Auxiliary heaterK63Radio, navigation and telephoneUniversal cellphone preparation (UHV)High (9ZB)On the UHV High system, the cellphone is connected exclusively via Bluetooth. In this case, only the voice data is transferred between the microphone, the control unit for cellphone operating electronics (J412) and the loudspeaker system of the vehicle. Communication with the GMS/UMTS network is via the cellphone aerial. This UHV features the following functions:Internal functions:● ●External functions:● ● ● ●Hands-free profile (HFP 1.5) BT audio streaming (A2DP 1.2) and controlConvenience radio/sat nav operation Multifunction display (MFD) Multifunction steering wheel, optional 3 button module in roof unitConvenience control dash panel insert (MFD+)2D ,A P F PGSM/ UMTS*CAN** Microphone in roof unitHJ412 Control unit for cellphone operating electronics3 button moduleMultifunction steering wheel, optionalLoudspeakerS488_110 RCD/RNS ** Always stands for signal transfer via CAN data bus, irrespective of bus designation and interconnected gateway. * Depending on cellphone/SIM card64High "baseplate" (9ZA)Compared with the UHV High (9ZB), this UHV features a baseplate. This serves to mount the telephone-specific charging cradle via which connection to the roof aerial takes place. When the cellphone is connected to the vehicle via the charging cradle, any radio communication (GSM/UMTS) from the vehicle is processed via the roof aerial. This UHV also features the following functions:Internal functions:● ●External functions:● ● ● ● ●● ●Hands-free profile (HFP 1.5) BT audio streaming (A2DP 1.2) and control (AVRCP 1.3) Voice-controlled operation (G2P/TTS) SMS speaking●Convenience radio/sat nav operation Multifunction display (MFD) Multifunction steering wheel, optional 3 button module in roof unit Baseplate for mounting special phone holder External aerial connection via phone holderConvenience control dash panel insert (MFD+) Microphone in roof unit J412 HFP, A2DP 3 button moduleCAN** Charging cradle with aerial connection to roof aerial GSM/ UMTS*Multifunction steering wheel, optionalLoudspeakerS488_112 RCD/RNS ** Always stands for signal transfer via CAN data bus, irrespective of bus designation and interconnected gateway. * Depending on cellphone/SIM card65Radio, navigation and telephonePremium (9ZU)The UHV Premium distinguishes itself from the UHV High "baseplate" by the internal GSM/UMTS module. A connection between the cellphone and the vehicle is not made (charger cradle optional) as the internal UHV module has access to the telephone data via Bluetooth by way of the Sim Access Profile (SAP). In this way, any radio communications (apart from Bluetooth) outside the vehicle are processed via the integrated GSM/UMTS module and the roof aerial. This UHV also features the following functions:Internal functions:● ●External functions:● ●● ● ●Hands-free profile (HFP 1.5) BT audio streaming (A2DP 1.2) and control (AVRCP) Voice-controlled operation (G2P/TTS) Sim Access Profile (SAP 1.0) SMS reading, writing and speaking● ● ● ●Convenience radio/sat nav operation Multifunction display (MFD) with Highline or Premium line dash panel insert Multifunction steering wheel 3-button module in roof unit Charger cradle External aerial connection via control unitConvenience control dash panel insert (Highline/Premium)FP SAP ,A , 2D PGSM/ UMTS Roof aerialCAN**Microphone in roof unitHInternal GSM/UMTS module3 button moduleMultifunction steering wheelLoudspeakerS488_114 RCD/RNS ** Always stands for signal transfer via CAN data bus, irrespective of bus designation and interconnected gateway.66Internal RNS315 (9ZI)The internal UHV of the RNS315 operates without additional external UHV control units. The cellphone is connected exclusively via Bluetooth. Only the voice data and command instructions are transferred in this case. GSM communication with the