TECHNICAL DOCUMENTATION

SSP 493 The Sharan 2011 Electrics

PDFEN40 pages2 MB
SSP 493 The Sharan 2011 Electrics - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingSelf-study Programme 493The Sharan 2011 Electrics/Electronics Design and Function For the first time, the Sharan 2011 features a large number of systems that have previously been used in higher class vehicles. The KESSY entry and start authorisation system is new, for example. KESSY allows convenient opening, locking and starting of the vehicle without active use of a key. The RNS 315 radio/navigation system is new, too. It features an integrated mobile telephone preparation and an internal flash data memory.This self-study programme also explains the following systems along with their components and functions:● ● ● ●the new electronic steering column lock (ESL) engine start and switch-off the mobile phone preparations (UMPP) the aerial systemsS493_026The self-study programme portrays the  design and function of new developments. The contents will not be updated.For current testing, adjustment and repair instructions, refer to the relevant service literature.Important Note2 ContentsIn Brief . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Vehicle Electrical System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Networking concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Convenience Electronics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Keyless Entry and Start System (KESSY) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Switching the engine on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Radio, Navigation and Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Radios . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Radio/navigation systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 RNS 315 radio/navigation system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Aerial systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Mobile phone preparation (UMPP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Replacing the electronic steering column lock (ESL) . . . . . . . . . . . . . . . . . . . . . 34 Updating the RNS 315 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Transponder coil for teaching-in and emergency starting . . . . . . . . . . . . . . . . 35 Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36Test Yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383 In BriefOverviewThe Sharan 2011 is based on the technology of the Golf class that has proven itself a million times over. At the same time, many systems are being used that were previously used in luxury class vehicles. The highlights will be presented briefly below and then looked at more closely in the corresponding chapters.KESSYThe new KESSY (Keyless Entry and Start System) is an equipment feature from higher classes that is now available for the Sharan. The system uses a range of sensors and transmitters to identify the key itself and its position. The system uses this information to establish when the vehicle can be unlocked, started and locked again without active use of the key.S493_031RNS 315Volkswagen is offering this radio and navigation system as an integrated multifunction entry-level unit. The 5" colour screen on the unit has been combined with a touch-sensitive surface (touch screen). The highlights of this version are the display of traffic signs, an SD card slot and an internal flash data memory. External data media can be controlled with the optional MDI module. The RNS 315 has an integrated mobile telephone preparation (UMPP).S493_0334 Aerial systemsS493_118The aerial system in the Sharan is integrated into the rear side windows and, depending on the equipment, into the roof aerial module. The Sharan is factoryequipped with radio systems as standard. Therefore there is no radio preparation.Mobile telephone preparation (UMPP)In terms of communications, Volkswagen is aiming for maximum flexibility with the highest level of user-friendliness no matter which version customers chose for their Sharan. The following mobile telephone preparations are available for the Sharan: UMPP High This basic preparation uses Bluetooth for communication between the mobile telephone and telephone control unit. A mobile telephone can be charged with a separately available 12V charging cable. UMPP High "Baseplate" This version also includes a 3-button control module  and a universal baseplate for mounting a telephonespecific charging cradle. The charging cradle has a connection to the roof aerial. While the mobile telephone is placed in the charging cradle, the connection to the GSM network will be made via this aerial.UMPP Premium This UMPP has an internal GSM/UMTS module. Up to three telephone books can be managed with this UMPP. Complete control of the mobile telephone can be transferred to the telephone system built into the vehicle via the SIM Access Profile (SAP). The vehicle transmission and reception unit (roof aerial module) and not the mobile telephone aerial is then used.Internal UMPP in RNS 315 A Bluetooth hands-free system is integrated into the RNS 315. This provides the same functions as the UMPP High in conjunction with an external microphone. The internal RNS mobile telephone preparation requires activation, however.5 Vehicle Electrical SystemNetworking conceptThe network in the Sharan 2011 is based on the Golf class. The immobilizer and KESSY functions are new additions. The entry and start authorisation control unit (J518) is installed for KESSY. The immobilizer features the electronic steering column lock (ESL) for the first time in this class. The ESL contains the electronic steering column lock control unit (J764).J364 J412 J503 J650 T16 d J367 J533 CX1 k J772J301 J386 J285 J362 Legend Powertrain CAN data bus Convenience CAN data bus Infotainment CAN data bus LIN data bus J387 J501 J518 J519CAN data bus wire LIN data bus wired kDiagnosis CAN data bus Instrument cluster CAN data bus * optional6 LegendCX1 - Alternator E313 - Selector lever J104 - ABS control unit J234 - Airbag control unit J245 - Sliding sunroof adjustment control unit J250- Electronically controlled damping  control unit J285 - Control unit in dash panel insert J301 - Air conditioning system control unit J343 - Left gas discharge bulb control unit J344 - Right gas discharge bulb control unit J362 - Immobilizer control unit J364 - Auxiliary heater control unit J367 - Battery monitor control unit J386 - Driver door control unit J387 - Front passenger door control unit J394 - Sunroof roller blind control unit J412 - Mobile telephone operating electronics  control unit J492 - All-wheel drive control unit J500- Power steering control unit J501 - Multifunction unit control unit J503 - Control unit with display for radio and navigation J518 - Entry and start authorisation control unit J519 - Onboard supply control unit J527 - Steering column electronics control unit J533 - Data bus diagnostic interface J558 - Left sliding door control unit J587 - Selector lever sensors control unit J605 - Rear lid control unit J623 - Engine control unit J650 - Multimedia system control unit J731 - Right sliding door control unit J743 - Mechatronic unit for dual clutch gearbox J745 - Control unit for cornering light and headlight range control J764 - Electronic steering column lock control unit J772 - Reversing camera system control unit J791 - Park assist steering control unit J810 - Driver seat adjustment control unit T16 - 16-pin connector Y7 - Automatic anti-dazzle interior mirrorE313 J104 J234 J250 J343 J344 J492J500 J587 J623 J743 J745 J791 Y7J245 J394J527 J558 J605 J731 J764 J810 S493_0607 Convenience ElectronicsKeyless Entry and Start System (KESSY)Vehicles equipped with the optional KESSY system can be opened, closed and started conveniently without the driver having to touch a key. The procedures for entry authorisation and engine start (immobilizer) need to be adapted for KESSY. Vehicles equipped with KESSY do not have a conventional ignition lock. The electronic steering column lock (ESL) is fitted in its place.Overview of componentsThe special feature of KESSY in the Sharan is that proximity sensors for detecting the open request are fitted only in the front door handles. The open request for the sliding doors and the tailgate is detected by microswitches in the handles. KESSY works with the following components:S493_039●Electronic  steering column lock  (ESL)S493_042●Proximity sensors in the door handles  on the driver and front passenger doors  (KESSY door handles)8 ●KESSY keyS493_040●Onboard supply control unitS493_044●KESSY control unitS493_046S493_041●Microswitches in all door handles  and the tailgateS493_056●LF aerials  (outside and inside)A glossary explaining specialist terms and abbreviations is provided at  the end of this document.S493_0509 Convenience ElectronicsKESSY keyThe key comes in the standard shape as also used in the Passat and Golf. In addition to the equipmentrelated buttons, it also contains the electronics for the remote control and also a KESSY chip (ID sender).  The remote control transmits and receives via low frequency (LF). The key receives KESSY signals via LF, but transmits replies via high frequency (HF).  The frequency table provides an overview.LF HFS493_058Frequency tableDescription LF  (low frequency) HF  (high frequency) Frequency 125kHz Usage Remote control;  KESSY transmissions to key KESSY transmissions from key433MHzEntry and start authorisation control unit (J518)LFOnboard supply control unit (J519)HFJ518 S493_044 S493_046J519The entry and start authorisation control unit (J518) is new for KESSY in the Sharan. The proximity sensors and all LF aerials are connected to this control unit. It is connected to the convenience CAN data bus and has a wake-up wire connected to the onboard supply control unit (J519).  Its tasks are:●The onboard supply control unit (J519) has an integrated wireless module with which it can receive KESSY signals via HF. It is connected to the convenience CAN data bus and also receives data via a wake-up wire connected to the entry and start authorisation control unit (J518). It takes on the following functions for KESSY:●● ●Evaluating the signals from the KESSY door handles and the LF aerials Communication with the immobilizer Transmission of KESSY communications to the key via the LF aerials●Waking the equipment on the convenience CAN data bus Receiving and forwarding KESSY communications from the key to J51810 LF aerials (KESSY transmission aerials)Iron core with coilm 8mKESSY transmission aerial (component)The KESSY transmission aerials are in the form of a coil around an iron core. The aerial shapes have been optimised for the respective mounting location in the vehicle. Compared with the aerials in the previous models, the components in the new Sharan are smaller. The aerial has a capture range covering a radius of 1.5 m.90 mm13m mS493_052Aerial position and capture ranges KESSY monitors the interior and an external area for keys. The exterior is monitored by three external aerials and the interior by three interior aerials. The key needs to be within the capture range of at least one LF aerial for KESSY functions to be available. The key can be located up to a distance of 1.5 m from the side or the rear of the vehicle.1.5 m1.5 mLegend LF aerial for interior KESSY monitoring area (interior)LF aerial for exterior 1.5 m S493_037 S493_048 KESSY monitoring area (exterior)11 Convenience ElectronicsKESSY door handlesOn the Sharan, all sensor and aerial electronics for the sides of the vehicle are built into the door handles on the driver and front passenger doors. These door handles can detect the presence of objects as they are equipped with proximity sensors. When your hand approaches the active sensors on the door handles, the electronics signal its presence. If you take hold of the door handle, this is evaluated as an opening request. However, if your hand approaches the smaller sensor on the door handle, this is interpreted as a locking request."Unlock" sensor (on inside of lever) S493_024 "Lock" sensor  KESSY door handle with proximity sensorsDesignThe part is moulded into the door handle and cannot be replaced separately. The following components are integrated into this part:●LF aerial●● ●A large capacitive sensor (proximity sensor) on the circuit board A small capacitive sensor (proximity sensor) next to the circuit board Circuit board with electronics An LF transmission aerialS493_025Circuit board with electronics "Unlock" capacitive sensor"Lock" capacitive sensorThe capacitance in the sensors increases as your hand approaches the door handle. This is detected by the electronics.You will find more information on the function of capacitive sensors  in self-study programme no. 374  "Traction Control and Assist Systems".12 MicroswitchesMicroswitches are fitted in each door handle and in the button on the tailgate. They send a signal when the handles are pulled or the button in the tailgate is pressed. The microswitches are only mentioned in the following explanations where they are essential to the understanding of KESSY. Microswitches in all door handlesS493_054Ignition/starter switch (D)The ignition/starter switch (D) is a single-stage,  four-pole switch that serves two redundant circuits. It is connected directly to the electronic steering column lock control unit (J764). In the Sharan, the ignition and engine can only be switched on via the ignition/starter switch. Both input pins on the ignition/starter switch must carry the same signal for the start request to be accepted by the electronic steering column lock control unit (J764). If only one input pin is working, the engine will not start and the electronic steering column lock control unit (J764) will signal an error.●The illumination of the ignition/starter switch is monitored by the entry and start authorisation  control unit (J518).Ignition/starter switch (D) Illumination (LED)●Inputs open means  Ignition/starter switch (D) not pressed Inputs to earth means  Ignition/starter switch (D) pressed.Electronic steering column lock control unit S493_110 (J764) Input pins13 Convenience ElectronicsElectronic steering column lock (ESL)The electronic steering column lock is being used for the first time in this vehicle class as part of the KESSY system. The vehicle can no longer be started with a key mechanism. The ESL is fitted in place of the omitted ignition lock. It is firmly fastened to the steering column with shear bolts and is housed there in a solid cast metal base with a steel sheet cover.Identification (visible differences)Conventional lock with mechanical steering wheel lock Electronic steering column lock (ESL)Steel sheet coverS493_011Connection for CAN data bus Inside the module The electronic steering column lock contains a motor, a gear mechanism with levers and the locking pin that locks the steering column. Inside the case, the electronic steering column lock control unit (J764) is accommodated on a circuit board together with two limit switches. The circuit board is bolted onto the mechanism at a 90° angle (see figure 62).14 Mechanical principle The motor simultaneously moves the locking pin, the "unlock" lever and the "lock" lever via the gear mechanism. The locking pin locks the steering column mechanically. The levers, which are facing the circuit board, actuate the limit switches when the locking pin reaches its fully extended or fully retracted position (see diagram).Electronic steering column lock control unit (circuit board)Mechanism"Unlocked" limit switch"Locked" limit switch"Unlock" lever Locking pin  Motor"Lock" lever Electrical principleS493_062The electronic steering column lock control unit (J764) is independent of the other electrical systems. It receives all authorisation and status information via the CAN bus. Only the ignition/starter switch (D) is connected directly to the ESL. The ESL implements the start request. It transmits this to the onboard supply control unit or the engine control unit in the form of a request from a terminal. The ESL will not retract the locking pin until the immobilizer control unit (J362) sends the unlock signal. Either the driver door must be opened after the ignition has been switched off or the vehicle must be locked for the ESL to lock the steering column. The electronic steering column lock control unit (J764) can distinguish three states:● ● ●"locked" "unlocked" "neither of the two"15 Convenience ElectronicsNetworking of componentsThe permanently installed parts of the system are networked together via the CAN data bus. KESSY transmits signals to the key via low frequency (LF). It does this via the LF aerials on the entry and start authorisation control unit (J518). The keys, however, always reply to KESSY via high frequency (HF). The onboard supply control unit (J519) receives the key’s replies and transfers them to the subscribers on the CAN data bus.J334LegendSensor Actuator Low frequency (LF) High frequency (HF)J623S493_116 J764 Driver door handle G415 R134 D J519 J518 R137 R138 R139 Interior aerialJ533Wake-up wireR136 Bumpers LF R135 G416 Front passenger door handleHFKey S493_064Legend (designation)D - Ignition/starter switch G415 - Driver door exterior handle  contact sensor G416 - Front passenger door exterior handle  contact sensor J334 - Immobilizer control unit J518 - Entry and start authorisation  control unit J519 - Onboard supply control unit J533 - Data bus diagnostic interface J623 - Engine control unit J764 - Electronic steering column lock control unit R134 - Driver side aerial for entry and start  authorisation R135 - Front passenger side aerial for entry and start authorisation R136 - Rear bumper aerial for entry and start authorisation R137 - Luggage compartment aerial for entry and start authorisation R138 - Interior aerial 1 for entry and start authorisation R139 - Interior aerial 2 for entry and start authorisation16 KESSY functionsThe procedures behind KESSY functions are explained in the following section. KESSY contains three function blocks:● ● ●KESSY entry (waking vehicle, checking key authorisation, releasing doors) KESSY go (unlocking electronic steering column lock and starting engine) KESSY exit (locking vehicle, protection against locking key inside vehicle)This book deals only with the procedures that are essential to understanding the system.KESSY entryIf the vehicle has been parked and locked, KESSY is in standby mode. Only the proximity sensors in the door handles of the driver and front passenger doors are monitored. Terminals S and 15 are de-energised and the steering column is locked.Waking the vehicle If you take hold of a KESSY door handle, the  corresponding proximity sensor signals the presence of your hand. The entry and start authorisation control unit (J518) will then search for KESSY keys via the LF aerials. The search covers a 360° area on the outside and inside of the vehicle. The KESSY control unit transmits a general request for all keys to identify themselves. To allow the replies from the keys to be received, the entry and start authorisation control unit (J518) wakes the onboard supply control unit (J519) via the wake-up wire. The control unit then switches from the standard frequency for remote control (LF) to the frequency for KESSY reception (HF).S493_068If KESSY keys reply within the capture area of the LF aerials, the onboard supply control unit (J519) wakes all subscribers on the convenience CAN data bus (CAN "wake-up") and transmits the received key IDs to the entry and start authorisation control unit (J518). The indicator LED on the key flashes while the key communicates with the vehicle.17 Convenience ElectronicsChecking key authorisation The entry and start authorisation control unit (J518) searches for a KESSY key near to the person who took hold of the door handle. The following happens:●●● ●●Keys inside the vehicle will be ignored during this search. An open request is confirmed for the key outside the vehicle. A security query is sent to the key. The key responds with the result of the security query and transmits a specific open request to the central locking system. If the result of the security query is correct, the entry and start authorisation control unit (J518) grants entry authorisation to the key.S493_023Release of doors In conjunction with the immobilizer control unit (J334), the onboard supply control unit (J519) checks the query with the specific open request from the key. If the key query is correct, the onboard supply control unit (J519) tells the door control units to unlock the doors. Mechanical unlocking only occurs when the door handle is touched directly (contact) and the microswitch in the door handle signals that the handle is being pulled. The door from which the open request is started is always unlocked first. Which other doors are also unlocked depends on the personal vehicle settings.S493_05418 KESSY goUnlocking the electronic steering column lock (ESL) and starting the engine The electronic steering column lock (ESL) function is identical to the previous versions except for one  difference:  When you press the ignition/starter switch (D), the ESL searches for authorised keys inside the vehicle. If an authorised key is found inside the vehicle, the ESL unlocks and the engine starts.  The authorisation is checked by the immobilizer control unit (J334).  The chapter "Switching the engine on and off" specifically looks at the engine procedures.S493_114The function of the 5th generation immobilizer is described in  self-study programme no. 470  "The Touareg 2011 Electrical/Electronics System".KESSY exitLocking the vehicle The engine needs to be switched off before the vehicle can be locked. If you then touch the lock area on the KESSY door handle, the sensor for outside door handle contact will signal the presence of your hand. The entry and start authorisation control unit (J518) then checks the key authorisation and position and gives the signal to lock the doors.S493_07019 Convenience ElectronicsProtection against locking the key inside the vehicle This safety function only concerns the key that was used last. If you leave the key in the vehicle during a locking query, KESSY recognises this state and offers two safety functions depending on the location of the key:● ●If the key is in the luggage compartment, the tailgate is unlocked when the tailgate handle is operated. If the key is in the passenger compartment, the vehicle will flash the lights four times and remain open for 30 seconds after the lock request. After the 30 seconds, KESSY will finally lock the vehicle to guarantee its security. The key left inside the vehicle is then locked in.If a key has been locked in the vehicle, you will not be able to start the vehicle with that key during the next starting procedure.Switching the engine on and offStarting the engineThe requirement for engine start (terminal 50) is that terminals S and 15 are energised. These terminals are connected when the ESL is unlocked. Depending on the vehicle equipment, the following conditions need to be fulfilled before the engine can be started:● ●●The clutch pedal switch must be actuated if the vehicle has a manual gearbox (interlock signal). On the DSG and automatic gearbox, the selector lever must be in the P/N position. In addition, if the vehicle has an automatic gearbox, you need to press the brake pedal. A valid key must be located in the interior before the engine can be started.20 There are two types of engine start procedure:● ●Manual engine start (without start/stop system) Automatic start (with start/stop system)Manual start During a manual start, the terminal 50 request is sent from the ESL to the onboard supply control unit (J519). The control unit then triggers the starter relay.  The starter is only active as long as the ignition/starter switch (D) is pressed. The switch should be pressed until the engine starts (glow periods need to be  observed for diesel vehicles). The selector lever information and the clutch signal are monitored by the onboard supply control unit (J519). The engine control unit (J623) supplies the brake signal.Automatic start For an automatic start, it is sufficient to press the  ignition/starter switch (D) briefly since the engine control unit (J623) activates the starter in this case  and automatically monitors whether the engine has started. In this variant, the engine control unit (J623) also monitors the clutch pedal switch and the position of the selector lever.Switching the engine offThe requirement for switching the engine off is that the engine is running and the vehicle is travelling at a speed less than 2 km/h. When you press the ignition/starter switch (D), the electronic steering column lock control unit (J764) de-energises terminal 15. The engine control unit (J623) then stops the engine. Panic switch-off If the engine needs to be switched off at speeds greater than 2km/h, you should press the ignition/starter switch (D) twice within one second or alternatively hold it for longer than one second.21 Radio, Navigation and TelephoneRadiosTechnical data Display Touch-sensitive (touch screen) AM, FM, TP and RDS reception (single tuner) AM, FM, TP and RDS reception (diversity tuner) Integrated DAB tuner (digital radio) Integrated drive Integrated SD/SDHC memory card reader Media support Audio input interface (AUX-IN) Telephone interface for telephone hands-free system Interface for connecting a reversing camera 4 x 20-watt loudspeaker output stages  (2 or 4 loudspeakers can be connected) Control of external CD changer Control of external amplifier Connection of external media devices (USB, mini USB, iPod) Speed-dependent volume control Brightness of display illumination can be controlled independently  of vehicle interior lighting Self-diagnosis and loudspeaker diagnosis Service test mode Optical parking system (OPS) Volume reduction setting for activation of the parking aid (PDC) Air-conditioning information Further information in self-study programmeRCD 210S493_027Monochrome, 122 x 36 pixels ●CD CD and MP3 audio data can be retrofitted ● (only mono channel) ● ● (no MP3, WMA)● ● ● ● ● no. 404* omitted from model year 2012 ** DAB version shown *** EU version without DAB shown22 RCD 310**S493_028RCD 510*** ●S493_035Monochrome, 302 x 45 pixels6.5", 400 x 240 pixels● Depending on equipment CD CD, MP3 and WMA audio data ● ● ●● Depending on equipment CD (6-disc changer) ● CD, MP3 and WMA audio data ● ● Depending on equipment ● ● (no MP3, WMA)*● ● ● ● ● ● ● ● ● no. 417● ● ● ● ● ● ● ● ● no. 42323 Radio, Navigation and TelephoneRadio/navigation systemsTechnical data Display Touch-sensitive (touch screen) AM, FM, TP and RDS reception (diversity tuner) Integrated DAB tuner (digital radio) Integrated drive Integrated SD/SDHC memory card reader Media support Audio input interface (AUX-IN) Support for telephone preparation Interface for connecting a reversing camera 4 x 20-watt loudspeaker output stages Control of external CD changer Control of external amplifier Connection of external media devices (USB, mini USB, iPod) Can be combined with TV tuner Speed-dependent volume control Brightness of display illumination can be controlled independently  of vehicle interior lighting Self-diagnosis and loudspeaker diagnosis Service test mode Optical parking system (OPS) Volume reduction setting for activation of the parking aid (PDC) Air-conditioning information Navigation function with map,  integrated direction symbols and speech Integrated memory media Navigation data Navigation data update Traffic sign display Further information in self-study programmeRNS 315 ● ●S493_0205", 400 x 240 pixelsOptional CD ● CD, MP3 and WMA audio data External and front of unit ●/+internal Bluetooth ● ● ● ● ● ● ● ● ● ● ● ● ● Flash memory*** (6GB/4GB NAR) Internal memory on SD card** ● no. 49324 RNS 510 ● ● DVD ●S493_0096.5", 800 x 480 pixelsCD, MP3, WMA audio, DVD formats External ● ● ● ● ● ● ● ● ● ● ● ● ● ● 30GB hard drive* Hard drive* DVD ● no. 423 * The hard drive is partitioned: 20GB are available for media data, and 10GB are reserved for the navigation data.** The purchased SD card can be used for all navigation units, but it is linked to the specific unit upon update and can then only used with that unit. *** Can only be used for navigation data.25 Radio, Navigation and TelephoneRNS 315 radio/navigation systemThe RNS 315 is based on the RNS 310. The main feature is the internal flash memory that keeps all map data (related to current region) constantly ready in the unit. There is no optical data medium (CD/DVD) so a corridor function (temporary storage of the route section) is no longer necessary. Like the RNS 310, the RNS 315 can be operated with the touch screen, rotary knob or buttons. The internal Bluetooth module must be enabled for the integrated UMPP to be available.S493_10226 Technical features● ● ● ● ●Equipment-dependent functions:●●● ● ● ●5" TFT colour display (touch screen) FM+RDS+TP via twin tuner AM Integrated CD drive (MP3/WMA) Navigation data in internal flash memory  (4GB NAR/ 6GB EU) SDHC card slot for navigation data update and media data (MP3 and WMA) TMC function and TMC background reception Display of air-conditioning information AUX-in interface on front of unit Display of optical parking system (OPS)● ●Integrated Bluetooth hands-free functions (HFP) with telephone book transfer and numeric keypad  on touch screen (activation via PR number required) Bluetooth audio streaming (A2DP) Map update via SD card (unit ID is written on card, card can only be used to update one unit)27 Radio, Navigation and TelephoneAerial systemsThere are a number of possible aerial configurations for the Sharan. The following section shows several examples of how these systems are connected.Radio with single aerial, telephone and auxiliary heaterThe radio aerials on all Sharan models are integrated into the two rear side windows. Depending on the equipment, the Sharan also has a combined roof aerial for GPS and GSM/UMTS. The signals for the auxiliary heater are also transmitted via the roof aerial.RCD 510 RCD 310 RCD 210 B Impedance transformer (AM/FM1)Auxiliary heaterIDAM/FM1 S493_004 Left RightAerial structure present, not assigned28 Aerial diversity, telephone and DAB, GPS (only RNS)The aerial structures in the side windows of the Sharan are the same in all models. Depending on the equipment selected for the Sharan, one of six different versions of the roof aerial module is added. Suitable impedance transformers are installed in single or double configuration depending on the equipment and market. In total, there are nine different impedance transformers: for example, with/without DAB (for ROW) and with/without TV (for Japan).RCD 510RNS 315B A II A B CDImpedance transformer  (AM/FM1) Impedance transformer (FM2/DAB)AM/FM1/ (TV1)FM2/DAB/ (TV2)S493_006 Left Legend: B I A C D G I FM1 /AM FM2 DAB GPS GSM/UMTS TV (Japan) Auxiliary heater Right29 Radio, Navigation and TelephoneMobile telephone preparation (UMPP)UMPP High (9ZB)The mobile telephone is only connected via Bluetooth with the UMPP High. This system only transfers the speech data between the microphone, the mobile telephone operating electronics control unit (J412) and the vehicle loudspeakers. The communication with the GSM/UMTS network occurs via the aerial in the mobile telephone. This UMPP has the following functions:Internal functions:● ●External functions:● ● ● ●Hands-free profile (HFP 1.5) BT audio streaming (A2DP 1.2) and controlUser-friendly radio/navigation operation Multifunction display (MFD) Multifunction steering wheel (MFW), optional 3-button module in roof moduleUser-friendly operation of  dash panel insert  (MFD+)2D ,A P F PGSM/ UMTS**CAN* Microphone in roof moduleHJ412 Mobile telephone operating electronics control unit3-button moduleMultifunction steering wheel, optional LoudspeakersRCD/RNS * Indicates signal transmission via CAN data bus, regardless of bus designation and  intermediate gatewayS493_038** Depending on mobile telephone/SIM cards30 UMPP High "Baseplate" (9ZA)Compared with the UMPP High (9ZB), this UMPP has a baseplate. This is used to mount a telephone-specific charging cradle through which the roof aerial is connected. If the mobile telephone is connected to the car via the charging cradle, all wireless communications (GSM/UMTS) will be handled by the vehicle via the roof aerial. This UMPP also has the following functions:Internal functions:● ●External functions:● ● ● ● ● ●● ●Hands-free profile (HFP 1.5) BT audio streaming (A2DP 1.2) and  control (AVRCP 1.3) Voice control (G2P/TTS) Speak text messagesUser-friendly radio/navigation operation Multifunction display (MFD) Multifunction steering wheel (MFW), optional 3-button module in roof module Baseplate for mounting a special telephone holder Exterior aerial connection via telephone holderUser-friendly operation of  dash panel insert  (MFD+)  Microphone in roof module J412 HFP, A2DP 3-button moduleCAN* Charging cradle with aerial connection to roof aerial GSM/ UMTS**Multifunction steering wheel, optional LoudspeakersRCD/RNS * Indicates signal transmission via CAN data bus, regardless of bus designation and  intermediate gatewayS493_036** Depending on mobile telephone/SIM cards31 Radio, Navigation and TelephoneUMPP Premium (9ZU)The UMPP Premium differs from the UMPP High "Baseplate" in its internal GSM/UMTS module. There is no need to physically connect the mobile telephone to the vehicle (a charging cradle is optional) as the internal UMPP module accesses the telephone data via Bluetooth using the SIM Access Profile (SAP). As a result, all wireless communications (except for Bluetooth) outside the vehicle are handled via the integrated GSM/UMTS module and the roof aerial. This UMPP also has the following functions:Internal functions:● ●External functions:● ●● ● ●Hands-free profile (HFP 1.5) BT audio streaming (A2DP 1.2) and  control (AVRCP) Voice control (G2P/TTS) SIM Access Profile (SAP 1.0) Display, write and speak text messages● ● ● ●User-friendly radio/navigation operation Multifunction display (MFD) with Highline or Premium Line dash panel insert Multifunction steering wheel (MFW) 3-button module in roof module Charging cradle Exterior aerial connection via control unitUser-friendly operation of  dash panel insert  (Highline/Premium)  Microphone in roof moduleGSM/ UMTS Roof aerialCAN*HFP SAP ,A , 2D PInternal GSM/UMTS module3-button moduleMultifunction steering wheel LoudspeakersRCD/RNS * Generally indicates signal transmission via CAN  data bus, regardless of bus designation and  intermediate gatewayS493_03432 RNS 315 internal UMPP (9ZI)The internal UMPP built into the RNS comes without additional UMPP control units outside the RNS 315, but does require activation. The mobile telephone is connected only via Bluetooth. Only the speech data and control instructions are transferred in this case. Communication with the GSM network occurs via the aerial in the mobile telephone. This UMPP has the following functions:Internal functions:● ●External functions:● ●Hands-free profile (HFP 1.5) BT audio streaming (A2DP 1.2) and controlUser-friendly radio/navigation operation Multifunction steering wheel (MFW), optionalUser-friendly operation of the dash panel insert  (MFD+)2D ,A P F PGSM/ UMTS**CAN* Microphone in roof moduleH LoudspeakersMultifunction steering wheel OptionalRNS 315S493_032*Generally indicates signal transmission via CAN  data bus, regardless of bus designation and  intermediate gateway** Depending on mobile telephone/SIM cards33 ServiceReplacing the electronic steering column lock (ESL)Replacing the componentWhen a Sharan is ordered with KESSY, the immobilizer functions are expanded to include the electronic steering column lock control unit (J764) in addition to the dash panel insert, the engine control unit and vehicle key. This means the electronic steering column lock may also need to be adapted when work is performed on the immobilizer function. Adapting is always necessary when the ESL is replaced. The ESL can generally be replaced without removing the steering column. Before removal, it should, however, be set to "unlocked" mode as terminal 15 supply is only available for enabling in this state. This is necessary if the ESL is to be re-installed. The electronic steering column lock is always delivered in unlocked state. When it is exchanged, a new set of shear bolts must be ordered and also a bracket on the steering column module must be replaced as these are destroyed upon removal.Teaching inThe latest generation of electronic steering column lock control units allows the control unit electronics to be adapted to the immobilizer any number of times. The further option of also adapting a used ESL to a vehicle (swapping parts) is particularly useful.CodingThe ESL must be coded in the respective vehicle for use with manual or automatic gearbox. The electronic steering column lock control unit automatically switches over to the function with or without start/stop system according to manual or automatic start.34 Updating the RNS 315The RNS 315 can be updated using an SD or SDHC card. This update applies to the navigation data in the unit. The update procedure generally runs in the same way as updates with CD/DVD. There is one important difference: An SD card that is suitable for all units is paired with the updated unit after the update and can only be used in that unit from then on. The SDHC cards for updating navigation data can be obtained through the same distribution channels as the CD/DVD updates. If the unit software needs to be updated at a later date (not planned at present), this will be performed exclusively by the dealerships using VAS test equipment.Transponder coil for  teaching-in and emergency startsIn the Sharan, the transponder coil, which is still in the same position as a conventional ignition lock, only has the function of a transponder emergency coil. It is used when the battery in the ignition key is flat or a new key has to be adapted at the workshop. In both cases, the coil is used for communication between the key and immobilizer. The ignition key needs to be held against the transponder coil during this procedure (see illustration for position). This allows the key ID to be read and the vehicle to be started even when the key batteries are flat.Steering wheel Operating lever on right of steering wheelS493_029 Position of emergency coil behind steering column trim Key35 GlossaryAM Amplitude modulation ASF Advanced Streaming Format or Advanced Systems Format:  A digital audio and video format developed by Microsoft AUX Auxiliary:  A connection channel for analogue audio signals like, for example, those transmitted from the headphone output of portable music players (MP3 players). AVRCP Audio Video Remote Control Profile:  A Bluetooth profile for remote control of audio or video equipment A2DP Advanced Audio Distribution Profile:  Industry-wide technology allowing stereo audio signals to be transmitted wirelessly via Bluetooth in one direction to a receiver. Bluetooth An industry standard developed by the Bluetooth Special Interest Group (SIG) for wireless transmission between devices over short distances DAB Digital Audio Broadcast:  Digital radio broadcasting FM Frequency modulation GPS Global Positioning Satellite system:  Satellite-supported global navigation and positioning system, originally for military usage GSM Global System for Mobile Communications:  Standard for digital mobile telecommunications  network HF High Frequency: Refers to electromagnetic waves in a frequency band between 3 and 30MHz.  This frequency band is also referred to as short wave. HFP Hands-free profile: Allows communication between a mobile telephone and vehicle hands-free system. KESSY Keyless Entry and Start System: This electronic system provides the driver with secure access to the vehicle without having to take the key in his hand.36 LF Low Frequency:  Refers to electromagnetic waves in frequencies  between 30 and 300kHz.  This frequency band is also referred to as long wave. RDS Radio Data System: A standard for additional radio information in car radios and mobile telephones, for example, station names, audio titles etc. SD Secure Digital card: Small and robust memory cards, e.g. for digital cameras, MP3 players etc. SDHC Secure Digital Card High Capacity:  Expansion of SD with storage capacity up to the maximum capacity of 32GB SAP SIM Access Profile (also SAP):  Bluetooth data transfer protocol that allows the UMPP to read the SIM card.  37 Test YourselfWhich answers are correct?1. Which statement about KESSY is correct? a) The entry and start authorisation control unit (J518) handles terminal control in addition to control of communications between the onboard supply and the vehicle key in a similar way to the Phaeton system. b) Apart from the remote control, the entry and start authorisation control unit (J518) receives the open request in electronic form only from the signals of the capacitive aerials in the front doors and the microswitches in the door handles of the sliding doors and the tailgate. c) The entry and start authorisation control unit (J518) codes itself automatically for automatic or manual versions according to the recognised vehicle equipment.2.Which statement about the electronic steering column lock (ESL) in the Sharan 2011 is correct? a) The ESL must be coded for the function type, i.e. manual start or automatic start, with the VAS tester. b) The ESL always sends the terminal 50 request to the engine control unit, which then checks the terminal 50 return line for plausibility. c) If the Sharan is equipped with KESSY and thus has an ESL, the electronic steering column lock control unit (J764) simulates or produces terminals S, 15 and 50 from the ignition/starter switch (D) signals. The ESL, which is self-diagnosis capable, receives the limiting condition via the CAN data bus. d) If the ignition/starter switch (D) connected to the ESL fails, the Sharan can still be started with the mechanical emergency start ignition lock.38 3.When is the electronic steering column lock (ESL) unlocked? a) After the driver door has been closed. b) When the immobilizer issues the unlock signal after the ignition/starter switch is pressed and the key authorisation is recognised. c) When the steering wheel is moved after a valid KESSY key has been recognised inside the vehicle.4.Which statement about replacing the electronic steering column lock (ESL) is correct? a) The ESL must always be replaced together with the dash panel insert, which houses the immobilizer. b) If it is going to be re-installed, you must make sure before removal that the ESL is in locked state (locking pin extended). c) The ESL can be replaced separately from all other immobilizer components and be adapted. This is even possible if the ESL being fitted is a used part.5.Which statement about the RNS 315 is correct? a) The unit comes in two versions: With DAB and 6GB internal memory (EU) or 4GB internal memory (NAR). b) The navigation data can be transferred from the supplied external data medium to an SD card as a backup. c) On the new RNS 315, navigation data updates are now only possible online over the Internet once the unit has been activated at an authorised dealership.Answers 1. b; 2. c; 3. b; 4. c; 5. a39 493© VOLKSWAGEN AG, Wolfsburg All rights and rights to make technical alterations reserved. 000.2812.50.20 Technical status 02.2011 Volkswagen AG After Sales Qualifizierung Service Training VSQ-1 Brieffach 1995 D-38436 Wolfsburg❀ This paper was manufactured from pulp that was bleached without the use of chlorine.