TECHNICAL DOCUMENTATION
SSP 495 The 3,0 l V6 TDI Engine

This PDF is currently unavailable.
Read document text
Service TrainingSelf-study programme 495The 3.0 l V6 TDI Engine (Generation 2) Design and functionThe first generation of the 3.0 l V6 TDI engine entered series production at Volkswagen in 2005 (it was first used by Audi in 2003). The 3.0 l V6 engine developed by Audi has been used in various VW Group models with great success. Over 1.6 million V6 TDI engines have now been built. Now in 2011, Volkswagen is introducing the second generation of this engine. This newly developed engine successfully combines low consumption figures, low emissions and a high level of power development with reduced engine weight. The focus was on minimising friction and achieving a lightweight design. The new V6 TDI generation comes in two output versions — a 180 kW version and a 150 kW version. An optimised piezo common rail injection system with up to 2,000 bar fuel rail pressure is used. The V6 TDI engine is already designed for future developments in terms of output, emissions and fuel consumption.S495_002The self-study programme presents the design and function of new developments! The content will not be updated.Current testing, setting and repair instructions can be found in the provided service literature.Important note2ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Engine Mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Engine Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43Test Yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 453IntroductionThe 3.0 l V6 150 kW TDI Engine (Generation 2) with Bosch common rail injection systemTechnical features• • • • • • Bosch common rail injection system with piezo injectors (2,000 bar injection pressure) Oxidising catalytic converter/diesel particulate filter Turbocharger from Honeywell Turbo Technologies (HTT) GT 2256 Innovative Thermal Management (ITM) Chain drive, new chain layout Demand-controlled in-tank fuel pumpS495_004Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Max. output Max. torque Engine management CJMA V6 engine with 90 V angle 2,967 cm3 83 mm 91.4 mm 4 16.8 : 1 Torque (Nm) Output (kW) Engine speed (rpm) S495_005 150 kW at 3,200 to 4,400 rpm 450 Nm at 1,250 at 2,750 rpm Bosch CRS 3.3 common rail injection system Diesel, according to DIN EN590 EU5°Torque and output diagramFuel Exhaust emissions standard4The 3.0 l V6 180 kW TDI Engine (Generation 2) with Bosch common rail injection systemTechnical features• • • • • • Bosch common rail injection system with piezo injectors (2,000 bar injection pressure) Oxidising catalytic converter/diesel particulate filter Turbocharger from Honeywell Turbo Technologies (HTT) GT 2260 Innovative Thermal Management (ITM) Chain drive, new chain layout Demand-controlled in-tank fuel pumpS495_004Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Max. output Max. torque Engine management CRCA V6 engine with 90 V angle 2,967 cm3 83 mm 91.4 mm 4 16.8 : 1 Torque (Nm) Output (kW) Engine speed (rpm) S495_055 180 kW at 3,800 to 4,400 rpm 550 Nm at 1,750 to 2,750 rpm Bosch CRS 3.3 common rail injection system Diesel, according to DIN EN590 EU5°Torque and performance diagramFuel Exhaust emissions standard5Engine MechanicsCrankshaft driveCrankcaseCylinder blockBalancer shaftCrankshaftBearing frameUpper part of oil sumpS495_006The basic design of the crankcase has been kept for the new generation of engines. High strength and high load-bearing capacity are crucial here. The proven bearing frame design has been retained for the crankshaft bearings for reasons of strength. By reducing the wall thicknesses throughout and by means of optimisation, it has been possible to reduce the weight of the crankcase by 8 kg compared with the previous generation and thus follow the principles of lightweight design.The deck-plate honing method has been used for the cylinder bores. This creates an optimum cylinder shape. The near perfect shape allows lower piston ring tension, which results in lower blow-by rates and lower mechanical friction.6Oil cooling annular channelTrapezoidal conrodTransverse bore in crankshaftSplit-pin conrod journalOil supply bore for conrod bearing Conrod bearingConrod bearing capS495_007The forged crankshaft uses a split-pin design in the 90° V engine to achieve equal firing intervals and improve the quiet running of the engine. Both the main bearing and the conrod bearing journals are induction hardened to ensure sufficient strength.The forged conrods are split diagonally and industrially cracked. Due to the high thermal loading, the aluminium pistons use a salt-core cooling gallery and splash oil cooling for optimum cooling of the piston crown and piston ring set.7Engine MechanicsChain driveHigh-pressure injection pumpTiming driveBalancer shaftOil/vacuum pumpAncillary drive S495_008The dual-chain drive on the gearbox end has been further improved for the V6 engine. In the timing drive, a relatively long roller chain with 206 links is used to drive the two inlet camshafts and the balancer shaft. The chains have a wear-resistant coating. This reduces the amount the chains stretch over long periods of usage. The ancillary drive chain is also a roller chain. It drives the high-pressure injection pump and the oil and vacuum pumps, which are combined in one case.The new chain layout has allowed the number of chains and chain tensioners to be reduced from four to two. The omission of two idler gears and the new drive system for the high-pressure pump without additional toothed belt drive also contribute to simplifying assembly and reducing friction and weight.8Cylinder headDesignOil separatorFine oil separator Constant-pressure valveAssembled hollow camshaftsCamshaft bearing bracketsTightly meshed·gears S495_009 Roller rocker fingers Glow plugThe proven four-valve combustion method has been taken from the previous engine with one tangential and one filling port on the inlet side and two combined exhaust ports. The inlet ports have been improved in terms of swirl and gas flow. The cooling concept of the cylinder head has been revised to keep the temperatures in the vicinity of the combustion chamber at an acceptable level. The exhaust ports have been positioned further apart and made smaller to increase the size of the coolant chamber. Furthermore, the coolant chamber has been designed so that a specific flow of coolant at high rates and optimum cooling is possible in the areas close to the combustion chambers. The coolant enters on the exhaust side via three separate ports for each cylinder.The main flow is guided between the exhaust valves and is then distributed among the remaining bridge areas between valves. The assembled hollow camshafts are fitted with split double bearing brackets (instead of ladder frame). This assembly sequence allows for a camshaft design without special clearances for fitting the cylinder head bolts. For acoustic reasons, the exhaust camshafts are driven via tightly meshed gears. The bearing diameter of the camshafts has been reduced from 32 mm to 24 mm to reduce friction.9Engine MechanicsClosing spring Swirls Oil returnCover with swirl channelS495_039 Oil separator module Inlet for blow-by gasesThe engine breather system has been moved from the inner V to the cylinder heads. Coarse and fine oil separators are integrated into both cylinder head covers. The crankcase breathers run via the pressure regulating valve to the suction side of the turbocharger.10Oil systemS495_0101. Pickup screen 2. Oil level and oil temperature sender G266 3. Oil pump 4. Vacuum pump 5. Non-return valve 6. Valve for oil pressure control N428 7. Thermostat 8. Engine oil cooler 9. Oil temperature sender G8 10.Filter bypass valve 11.Oil filter12.Oil pressure switch for reduced oil pressure F378 13.Oil pressure switch F22 14.Crankshaft 15.Spray jets for piston cooling 16.Camshafts for cylinder bank 1 17.Camshafts for cylinder bank 2 18.Chain tensioner 19.Turbocharger 20.Oil return 21.Sump11Engine MechanicsVolumetric flow-controlled oil pump with vacuum pumpThe oil pump with two pressure stages from the 4.2 l V8 TDI engine is also used on the new 3.0 l V6 TDI engine. The volumetric flow-controlled vane pump can change its supply characteristics by means of an eccentrically mounted adjusting ring. The oil pump switches between the pressure stages depending on the engine load, engine speed and the oil temperature. The configuration as a pump combination is new. The oil pump and the vacuum pump are combined in one housing. The two pumps are driven by the chain drive system on the gearbox side via a stub shaft. The vacuum pump produces the vacuum by means of a rotor with adjustable vanes.DesignVacuum pump housing Ball valve Oil pump housing Vane cells Ball valve Adjusting ring Vacuum pump coverDrive shaftRotor with vanes (vacuum pump)Control springs S495_011 Oil pump cover Intake manifoldYou will find further information on the volumetric flow-controlled oil pump in self-study programme no. 467 “The 4.2 l V8 TDI engine with common rail fuel injection system”.12Oil level sensorAn electronic oil level sensor is used in Volkswagen vehicles featuring the 3.0 l V6 TDI (for example, the Touareg). A conventional oil dipstick is not used. The oil level sensor works with ultrasound. The emitted ultrasonic pulses are reflected by the boundary layer of oil and air.Oil level sensorMeasuring unitSealSensor base with electronic measuring system 3-pole connector housingS495_012Operating principleThe oil level is calculated from the time difference between the transmission and the return of the pulse. A PWM (Pulse Width Modulated) signal is transmitted.Oil level sensor Output with pulse-width modulated signalTemperature Fill levelDigital LogicEvaluationS495_040The design and function of the oil level sensor is described in self-study programme no. 467 “The 4.2 l V8 TDI engine with common rail fuel injection system”.13Engine MechanicsAir intakeThe intake air reaches the throttle valve from the front end via a plastic air duct. A short plastic air pipe is connected to the throttle valve. The recirculated exhaust gases are fed into the intake connecting pipe via a thermally decoupled sheet metal structure in a way that aids the air flow. When the exhaust gases are fed in, deposits on the inside plastic wall can be avoided in all operating modes thanks to the geometric shape. At the same time, it ensures a good mixture. Only one central swirl flap is used for swirl regulation in this new generation of engines compared with the previous six individual flaps in the previous generation. The intake manifold has two air paths from the swirl flap to the two cylinder banks. The upper part leads the flow of air to the swirl ports and the lower part goes to the filling ports. The intake manifold geometry has been further improved with regard to pressure loss and even distribution of the air flows to the individual cylinders. The reduction in pressure losses improves performance and consumption. The plastic intake manifold consists of three shells and is friction welded.Central swirl flapExhaust gas recirculation inletThrottle valve module J338 S495_01314Exhaust gas recirculation (EGR)The exhaust gas recirculation system plays a decisive role in meeting the emissions standards. The components of the exhaust gas recirculation system, i.e. exhaust gas recirculation valve, exhaust gas recirculation cooler and bypass valve, are combined in the EGR module. The EGR system collects the exhaust gases at the turbocharger housing. It has been optimised to reduce pressure losses related to the high recirculation rates. The cooling performance of the EGR system has been optimised so that, despite the omission of the separate low-temperature coolant circuit, the same EGR cooling performance is achieved as for the previous engine. The exhaust gas recirculation cooler has been incorporated into the cylinder head circuit. It is no longer supplied with cold coolant from the main radiator. This causes the temperature of the coolant supplied to the EGR cooler system to rise. The cooling performance of the exhaust gas recirculation cooler has, however, been increased by approx. 1 kW. As a result, it was possible to slightly increase the cooling performance of the whole system. The advantage of the new EGR cooling system is its greatly reduced complexity. This includes the incorporation of the EGR coolant circuit into the cylinder head circuit of the new dual-circuit cooling system. Furthermore a considerable reduction in weight has also been achieved.Turbocharger 1 control unit J724 Pulsation damper Integral insulationTurbochargerExhaust gas recirculation pipeExhaust gas recirculation control motor V338 Exhaust gas recirculation cooler Exhaust gas recirculation temperature sensor G98Flexible jointExhaust manifold, with air-gap insulationIntake manifold inletS495_01415Engine MechanicsCooler for exhaust gas recirculationThe newly developed electrically operated exhaust gas recirculation valve is located on the “hot side” of the engine. To reduce pressure loss, the seat diameter of the valve has been enlarged from 27 mm to 30 mm for the new generation. The high-performance exhaust gas recirculation cooler is made from stainless steel in a pipe design and is integrated into the aluminium housing of the EGR module. A pneumatic lift valve is fitted instead of a flap to bypass the cooler if necessary. Compared with a flap that inevitably always has a gap, a lift valve guarantees a tight seal during cooling operation. This is an advantage in achieving maximum cooling performance. An EGR temperature sensor (G98) is built into the exhaust gas outlet of the EGR module. The exhaust gas temperature downstream of the cooler is regulated to a minimum value with this temperature sensor. In this way, the aim of cooling the recirculated exhaust gas as much as possible to minimise NOx emissions and, at the same time, to prevent the formation of condensation can be achieved.Exhaust gas recirculation coolerCoolant temperature sender G62 Actuator motor for exhaust gas recirculation V338Coolant return to oil filter module and thermostat housingExhaust gas recirculation temperature sensor G98Exhaust gas recirculation valve (EGR valve) Bypass valve for EGR cooler Coolant supply from cylinder headS495_01516TurbochargerThe turbocharger has been adapted for the increased performance requirements of the new 3.0 l V6 engine generation. Each performance version of the engine uses a different turbocharger from Honeywell Turbo Technologies (HTT). The turbocharger GT 2256 is fitted on the 150 kW version and the turbocharger GT 2260 is fitted on the 180 kW version. The turbocharger has been optimised in many areas. Both the compressor wheel and turbine have been improved again and the bearings for the rotating parts have been further developed to reduce friction. This allows fast response and an even torque development.Actuating lever for wastegateTurbocharger 1 control unit J724Integral insulationConnection to exhaust systemConnection to intake manifoldConnection to exhaust gas recirculationS495_01617Engine MechanicsCharge air coolingThe whole charge air system has been revised from the air filter to the turbocharger. On the pressure side, it has been possible to further optimise the air duct system with the charge air cooler by using low-turbulence hose connections. In this way, the response of the engine and the emissions and consumption figures could be improved.TurbochargerAir filter Throttle valve module J338Air intakeCharge air coolerS495_017 Charge pressure sender G31 and intake air temperature sender G4218Cooling systemCylinder head coolant circuitThe permanently flowing cylinder head coolant circuit mainly consists of the coolant chambers in the cylinder heads, the exhaust gas recirculation cooler, the oil cooler, the heating and gearbox oil heat exchanger and the main radiator. The cylinder head coolant circuit is regulated by a heatable thermostat with a wax thermostatic element (see page 22 and 23). The thermostat is not energised during the warm-up phase of the engine and opens at approx. 90 °C. As a result, no heat is transferred to the main radiator until this temperature is reached. The hot coolant is supplied to warm up the gearbox and, if necessary, for the heating and ventilation system. Energising the wax thermostatic element allows the temperature of the cylinder head circuit to be reduced within the physical limits of the main radiator. The conditions for this are: • • • Cylinder head component protection Maximum EGR cooling requirement Gearbox cooling requirementPneumatic regulating valve (operation of the cylinder head and cylinder block coolant circuit)Engine oil coolerS495_019 Cylinder block coolant circuit closed Cylinder head coolant circuit Cylinder block coolant circuit19Engine MechanicsCylinder block coolant circuitThe coolant for the cylinder block coolant circuit reaches the exhaust side of the cylinder banks via non-return valves in the cylinder block. The non-return valves prevent a return flow of coolant between the cylinder banks and unwanted heat transfer from the cylinder block. This ensures a controlled flow in the circuit. The cylinder block coolant circuit is closed via a vacuum-controlled ball valve. The coolant is stationary, the warm-up phase of the engine is shortened and friction is reduced. The temperature level of the cylinder block coolant circuit is regulated at approx. 105 °C with the aid of the ball valve. As a result, the crankshaft group works at the best possible friction temperature level. One major focus during the development was achieving the “stationary coolant” in the cylinder block coolant circuit. The ball valve is activated by the coolant valve for cylinder head N489 using pulse-width modulation (PWM). To help the system warm up quickly, an engine oil cooler bypass is also fitted in the oil system.Return via cylinder headEngine oil coolerCylinder headS495_020 Cylinder block coolant circuit open Cylinder head coolant circuit Cylinder block coolant circuit20Bleeding the systemThe cylinder block coolant circuit has its own bleeder valve. The cylinder banks are connected via the cylinder head gasket to collectors in the cylinder heads. This allows air bubbles in the cylinder block circuit to escape at the highest point of the system even when the coolant is stationary. The bleeder lines run from the collectors to a bleeder valve. The bleeder valve connects the permanent bleeder system of the cylinder head coolant circuit to the bleeder system of the cylinder block circuit. The valve seals the two sub-circuits from each other with the aid of a floating ball.Bleeder valveFrom cylinder head coolant circuit to coolant expansion tankFrom cylinder block coolant circuit S495_02121Engine MechanicsEngine oil cooler with thermostat-controlled bypass channelThe engine oil cooler is equipped with a thermostat-controlled oil cooler bypass.DesignMount for coolant pump drive wheelThermostatS495_02222FunctionThe expanding wax element in the thermostat opens a bypass valve at the engine oil cooler when the oil temperature is 103 °C. The main flow of oil is thus sent past the engine oil cooler. The thermostat is fitted below the coolant pump on the cylinder block.Coolant pump housingCylinder blockGuide sleeveLifting pinSpringExpanding thermostatic element S495_02323Engine MechanicsInnovative thermal management system for 3.0 l V6 TDI engine (generation 2)During the development of the 3.0 l V6 TDI engine (generation 2), particular attention was paid to thermal behaviour. The aim of the thermal management system is to reduce the warm-up time of the engine and increase the temperature in the partial load range so that the engine runs at a good friction level.The cooling system uses a split-cooling concept in which the cylinder block and cylinder head each have their own coolant circuits. This allows the ideal temperatures to be set for the cylinder block and cylinder head even when the engine has reached operating temperature. The coolant pump, which is located at the front of the engine inner V, continuously delivers coolant to the crankcase on the exhaust side of the engine. The flow of coolant is split there between the cylinder heads and the crankcase. Once coolant has flowed through the two sub-circuits, the flow of coolant reaches the suction side of the coolant pump.Thanks to the split cooling concept, the innovative thermal management system used in the new 3.0 l V6 TDI engine allows an independent supply of coolant to the interior and gearbox oil heaters regardless of whether the coolant in the cylinder block is stationary. We have managed to reduce the emissions and consumption figures considerably since each sub-circuit is operated at the temperature that ensures minimum friction.24Always follow the instructions in the workshop manual when filling the cooling system.Key: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20Radiator Radiator fan Radiator outlet coolant temperature sender G83 Thermostat for map controlled engine cooling F265 Coolant pump Engine oil cooler Oil level and oil temperature sender G266 Cooler for exhaust gas recirculation Coolant shut-off valve Cylinder head Coolant temperature sender G62 Cylinder block Temperature sender for engine temperature regulation G694 Coolant expansion tank ATF cooler Coolant valve for gearbox N488 Coolant circulation pump V50 Auxiliary heater 3/2-way valve Heat exchanger for heaterS495_01825Engine MechanicsFuel systemSchematic overview1 Fuel delivery unit Constantly delivers fuel to the presupply. 2 3 Pressure-resistant fuel filter 11 Fuel temperature sender G81 Measures the current fuel temperature. 4 Dual-piston high-pressure pump Generates the high fuel pressure required for injection. 5 Fuel metering valve N290 Regulates the quantity of fuel to be pressurised as required. 6 Pressure retention valve/restrictor A pressure of 3.5 – 10 bar is present in the return from the injectors. 7 8 Injectors for cylinders 1 - 6 N30 - N33, N83, N84 Fuel pressure sender G247 Measures the current fuel pressure in the highpressure range. 9 Fuel pressure regulating valve N276 Regulates the fuel pressure in the high-pressure range. 12 Engine control unit J623 Fuel pump control unit J538 10 High-pressure accumulator (rail) Stores the fuel required for injection into all cylinders at high pressure.26High pressure Presupply pressureReturn pressure Return line from injectorsS495_02427Engine MechanicsFuel delivery unitThe fuel delivery unit GX1 basically consists of two sections: • The fuel level sender that uses 3-conductor technology and detects the fuel level in the fuel tank. The fuel system pressurisation pump G6 that uses an EC motor. The EC motor is a brushless, permanently activated synchronous motor. Thanks to its brushless design, the motor is wear-free except for the bearings. The fuel system pressurisation pump G6 is activated by the fuel pump control unit J538. A PWM signal is used for activation by the engine control unit J623. Error feedback messages are sent via the same wires. This guarantees a demand-regulated supply of fuel.•Fuel supply for auxiliary heaterFuel returnFuel presupplyElectrical connection Fuel delivery moduleFuel pressurisation pump G6S495_02528Fuel pressurisation pump G6The fuel system pressurisation pump G6 uses an EC motor (EC = electronically commutated). The motor is made up of a rotor, stator, pump chamber and housing with connection piece. The rotor is a permanent magnet and the stator is an electromagnet. The brushless motor in the fuel pump contains two pairs of permanent magnets and three pairs of electromagnets. The change in the current direction (commutation), which is necessary for rotation, is controlled by an external electronic control unit (fuel pump control unit J538). There is therefore no contact between the moving parts of the motor and operation is virtually wearfree.Connection pieceRotorMotor housingStator with coilsPump chamberS495_03029Engine MechanicsFunction of fuel pump The fuel pump control unit J538 switches between the individual phases. The switching must be timed precisely in order to create a rotating magnetic field in the stator coil. The permanent magnet pairs force the rotor to realign itself and thus follow the magnetic field. This causes rotation. The fuel pump produces mechanical rotation in twelve individual steps. The control unit recognises the position of the rotor from the de-energised coil pair. The Back-EMF Signal (ElectroMotive Force feedback signal) is used for this.Functional principleStatorRotorPermanent magnetCoilBack-EMF signal S495_027Circuit of coil windings UIV WOutput stageElectronic control Star point S495_02630Common rail fuel injection systemThe 3.0 l V6 TDI engine (generation 2) features a Bosch common rail injection system that uses piezo injectors. The maximum injection pressure is 2,000 bar. Each different engine version has its own injector nozzle configuration. The piezo injectors are connected to the forged fuel rails via very short injector pipes. The rail pressure is generated by a dual-piston high-pressure pump, the CP 4.2. The high-pressure pump is located in the inner V on the gearbox side. The pump is driven directly by the crankshaft via the ancillary drive chain. A ratio of 1 : 0.75 to the crankshaft has been chosen to ensure fuel delivery is in sync with the injectors. The pump is fitted on the engine timed to the injection phases to reduce the chain forces.S495_02831Engine MechanicsDesign of the high-pressure pump CP 4.2The high-pressure pump works with two pistons and is driven via the ancillary drive chain. It generates a maximum injection pressure of 2,000 bar.S495_032Suction valveFuel metering valve N290Outlet valve Pump piston Connection to rail Piston spring Fuel supplyRollerFuel returnOverflow valve Drive shaftDrive cams S495_033The illustration shows a cross-section of the dual-piston high-pressure pump through only one pump piston.32How the high-pressure pump worksSuction and delivery strokes are performed one after the other by the pistons, which are offset by 90°. The delivery stroke pushes fuel alternately into the left and right rails. The fuel metering valve distributes fuel evenly between the intake channels for the two pump pistons.Fuel metering valve N290Pump piston 1 Intake channel Suction valve Intake channelPump piston 2Outlet valveConnection to rail 1Connection to rail 2Overflow valvePiston spring Roller Fuel return Fuel supply Drive shaft Drive cam Drive cam Microfilter S495_03433Engine MechanicsHigh-pressure fuel systemFuel metering valve N290The fuel metering valve is part of the high-pressure pump and regulates the fuel quantity required to generate high pressure. This has the advantage that the high-pressure pump only has to generate the pressure required for the current operating situation. In this way, the power consumption of the high-pressure pump is reduced and unnecessary heating up of the fuel is avoided.How it works When no current is supplied, the fuel metering valve is open. The valve is actuated by the engine control unit with a pulse-width-modulated signal (PWM) in order to reduce the supply quantity to the compression chamber. The fuel metering valve is pulsed closed by the PWM signal. Depending on the pulse duty factor, the position of the control piston and thus the fuel supply quantity in the compression chamber of the respective pump piston 1 or 2 are changed.Supply from inside of pumpFuel metering valve N290Control pistonCompression chamber pump piston 1Compression chamber pump piston 234S495_036Overflow valveThe fuel pressure in the low-pressure area of the high-pressure pump is regulated by the overflow valve.How it works The fuel system pressurisation pump G6 delivers fuel from the fuel tank to the high-pressure pump at a pressure of approx. 5 bar. This safeguards the supply of fuel to the high-pressure pump in all operating conditions. The overflow valve regulates the fuel pressure in the high-pressure pump to approx. 4.3 bar. The fuel delivered by the fuel system pressurisation pump G6 works against the piston and the piston spring of the overflow valve. When the fuel pressure rises above 4.3 bar, the overflow valve opens and opens up the path for return of the fuel. The excess fuel flows via the fuel return line into the fuel tank.Overflow valveFuel return Fuel supply S495_04135Engine MechanicsHigh-pressure generationSuction stroke The downwards motion of the pump piston increases the volume of the compression chamber. As a result, the pressure of the fuel in the high-pressure pump and the pressure in the compression chamber differ. The suction valve opens and fuel flows into the compression chamber.Suction valveCompression chamberS495_03736Delivery stroke Once one of the pump pistons starts to move upwards, the pressure in the corresponding compression chamber rises and the suction valve closes. As soon as the fuel pressure in the compression chamber rises above the pressure in the high-pressure area, the outlet valve (non-return valve) opens and fuel is delivered to the high-pressure accumulator (rail).Outlet valveConnection to highpressure accumulator (rail 1)S495_03837Engine ManagementSystem overviewSensorsAir mass meter G70 Engine speed sender G28 Hall sender G40 Coolant temperature sender G62 Radiator outlet coolant temperature sender G83 Fuel temperature sender G81 Temperature sender for engine temperature regulation G694 Oil level and oil temperature sender G266 Fuel pressure sender G247 Accelerator position sender G79 Accelerator position sender 2 G185 Exhaust gas recirculation potentiometer G212 Brake light switch F Charge pressure sender G31 and intake air temperature sender G42 Lambda probe G39 Diagnosis connection Oil temperature sender 2 G664 Oil pressure switch F22 Oil pressure switch for reduced oil pressure F378 Exhaust gas temperature sender 3 (after catalytic converter) G495 Exhaust gas recirculation temperature sensor G98 Exhaust gas temperature sender 1 G235 Exhaust gas temperature sender 4 (after particle filter) G648 Pressure differential sender G505 Engine control unit J62338ActuatorsInjectors, cylinders 1 - 3 N30, N31, N32 Injectors, cylinders 4 - 6 N33, N83, N84 Automatic glow period control unit J179 Glow plugs 1 - 3 Q10, Q11, Q12 Glow plugs 4 - 6 Q13, Q14, Q15 Valve for oil pressure control N428Throttle valve module J338Fuel metering valve N290Fuel pressure regulating valve N276Actuator motor for exhaust gas recirculation V338 Exhaust gas recirculation cooler changeover valve N345 Coolant valve for cylinder head N489 Turbocharger 1 control unit J724Map-controlled engine cooling system thermostat F265Fuel pump control unit J538(Left, right) electrohydraulic engine mounting solenoid valves N144, N145 Lambda probe heater Z19 Fuel pump relay J17 Fuel system pressurisation pump G6 S495_04639Engine ManagementExhaust gas treatmentDesign of exhaust systemThe exhaust system for the new 3.0 l V6 TDI engine features an improved oxidising catalytic converter and a coated diesel particulate filter. The oxidising catalytic converter and the diesel particulate filter are positioned separately one after the other in the exhaust system due to design features. The oxidising catalytic converter is flanged onto the turbocharger close to the engine via a short input pipe. An intermediate pipe, the flexible joint and the diesel particulate filter then follow the oxidising catalytic converter. The connection to the rear silencer is formed by the output pipe on the diesel particulate filter and the inlet pipe for the rear silencer. The rear silencer has two tailpipes.Output pipe (diesel particulate filter) Clamp TurbochargerInput pipe with flange Oxidising catalytic converter Flexible jointDiesel particulate filter Intermediate pipe40In order to cover the widest possible frequency range for noise absorption, the exhaust system uses a combination of reflection silencer and absorption silencer. Reflection silencers mainly dampen the low frequencies by means of the noise reflection principle. Absorbtion silencers primarily absorb the high frequencies. The noise energy is converted into heat in this case.Input pipe (rear silencer)TailpipeRear silencerS495_04841Engine ManagementOxidising catalytic converter and diesel particulate filterThe oxidising catalytic converter has a volume of 1.67 l. The volume of the diesel particulate filter is 4.08 l. Thanks to its aluminium titanate coating, the diesel particulate filter has considerably longer regeneration intervals. For the first time, a triple post-injection is being used in the 3.0l V6 TDI engine during particulate filter regeneration to increase the exhaust gas temperature in low-load operation. A safe and quick burn-off of particulates is thus guaranteed in all driving conditions, particularly in slow-moving traffic. The thermal energy required for this is generated by two combusting post-injections that come in quick succession. The third late post-injection uses very small injection quantities. The triple post-injection also ensures diesel particulate filter regeneration when the exhaust gases are colder. At the same time, oil dilution is minimised and the life of the oxidising catalytic converter is extended.Lambda probe G39TurbochargerInput pipe with flangeOxidising catalytic converterConnection for exhaust gas temperature sender 1 G235 Connection for pressure differential sender G505Diesel particulate filter Intermediate pipeFlexible jointConnection for exhaust gas temperature sender 3 G495S495_04942ServiceSpecial toolsDesignation Tool ApplicationT40048Assembly tool for crankshaft sealS495_059 T40094 T40094/1 T40094/2 T40094/9 T40094/10 T40094/11 T40094/12 Camshaft removal and fitting toolS495_051 T40096 Camshaft fitting toolS495_053 T40245 Locking pin for chain sprocketS495_05743ServiceDesignationToolApplicationT40246Bracket for securing chain tensionerS495_058 T40248 Counterhold tool for high-pressure pumpS495_060 VAS 5161 Removal and installation device for valve cottersS495_05644Test YourselfWhich answers are correct?One or several of the given answers may be correct. 1. ❒ ❒ ❒ How is the high-pressure pump driven? a) The high-pressure pump is driven by the crankshaft via spur gearing. b) The high-pressure pump is driven by the inlet camshaft of cylinder bank 2 via a toothed belt. c) The high-pressure pump is driven via the ancillary drive chain.2.How is the swirl of the intake air regulated? a) By swirls flaps for each cylinder. b) Only by specially shaped swirl channels. c) By a central swirl flap.❒ ❒ ❒3.Which statement about the EGR cooling system is correct? a) The EGR coolant circuit is a separate coolant circuit. b) The EGR coolant circuit is integrated into the cylinder head coolant circuit. c) The EGR coolant circuit is part of the cylinder block coolant circuit.❒ ❒ ❒4.Which statement about the thermal management system for the 3.0 l V6 TDI (generation 2) is true? a) The coolant circuit uses the split cooling concept. b) The cylinder head and cylinder block coolant circuits are separate. c) The cylinder head and cylinder block have a common, non-separable coolant circuit – the coolant pump can be switched off (stationary coolant).❒ ❒ ❒45Test Yourself5.At what temperature does the thermostat for the oil cooler bypass open? a) Oil temperature 70 °C b) Oil temperature 120 °C c) Oil temperature 103 °C❒ ❒ ❒6.How high are the injection pressures for the two engine output versions? a) 1,800 and 2,000 bar b) 1,600 and 2,200 bar c) 2,000 and 2,200 bar❒ ❒ ❒Answers: 1.) c) 2.) c) 3.) b) 4.) b) 5.) c) 6.) a)46Notes47495© VOLKSWAGEN AG, Wolfsburg All rights reserved including the right to make technical alterations. 000.2812.52.20 Technical status 06/2011 Volkswagen AG After Sales Qualification Service Training VSQ-1 Brieffach 1995 D-38436 Wolfsburg❀ This paper has been manufactured from pulp bleached without the use of chlorine.