TECHNICAL DOCUMENTATION
SSP 498 The Golf Cabriolet 2012

This PDF is currently unavailable.
Read document text
Service TrainingSelf-study programme 498The Golf Cabriolet 2012The Golf Cabriolet 2012 - the continuation of a great tradition. Presented as a four-seater cabriolet based on the Golf 2009, this model comes in a completely open format without roll bar. The design shows its individual character compared with the Golf hatchback thanks to the new rear end, the flat roof line and the greater inclination of the windscreen frame. One technical highlight is the fully automatic electrohydraulic fabric convertible roof that can be opened in 9 seconds at vehicle speeds up to 30 km/h. Maximum safety is provided by an active roll-over protection system, airbags for the driver and front passenger, head-thorax airbags for the front seats and a knee airbag on the driver's side. It has been possible to improve the high level of static and dynamic stiffness even further compared with the hatchback by adding special structural reinforcements to the underbody, the side panels, the sills, the rear bulkhead and the doors. The new Golf Cabriolet provides a high level of ride comfort and features the quietest and one of the most spacious interiors in its class. The luggage compartment volume is 250 litres, which is also fully usable when you open the convertible roof. The new Golf Cabriolet 2012 is characterised by elegance, dynamics, convincing quality and precision.s498_007The self-study programme presents the design and function of new developments! The content will not be updated. Current testing, setting and repair instructions can be found in the provided service literature.Important note2ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Electrohydraulic Convertible Roof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Occupant Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40Engines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Running Gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52Heating and Air Conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54Electrical System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Convenience Electronics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58Radio, Navigation and Telephone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 603IntroductionThe Golf Cabriolet 2012The Golf Cabriolet success storyThe start of production for the new Golf Cabriolet in March 2011 sees Volkswagen continue the success story of the Golf Cabriolet built between 1979 and 2002. It is being built at Volkswagen's Osnabruck plant in the German state of Lower Saxony. The factory covers all stations of the automobile process chain from vehicle development to tooling and production.Osnabrück Wolfsburgs498_012The Golf Cabriolet through the erasFrom the introduction of the first Golf Cabriolet in 1979 until the end of production in 2002, the Golf Cabriolet sold over 680,000 units across the world.s498_3454Overview of equipment featuresThe list below shows you important standard and optional equipment for the new Golf Cabriolet 2012. The range of options builds on the standard equipment by means of equipment and design packs. These may vary from country to country.Here are some of the equipment features for the new cabriolet: • • • • • • • • Xenon headlights with cornering lights and LED daytime running lights incl. front fog lights, optional Tinted tail lights using LED technology Electrohydraulic fabric roof, fully automatic Undivided rear seat bench, backrest split symmetrically, foldable Knee airbag on driver's side Active roll-over protection system Start/stop system* Windbreak, optional* Only for BlueMotion technologys498_0115IntroductionTechnical dataExterior dimensions and weightsThe data refers to a vehicle without driver, with standard equipment, a 1.2l 77kW TSI engine and tyre size 205/55 R16.2,578 mm 4,246 mm1,423mm1,535 mm 1,782 mm1,508 mms498_327Exterior dimensionsLength Width Height Wheelbase Track width at front Track width at rear 4,246 mm 1,782 mm 1,423 mm 2,578 mm 1,535 mm 1,508 mmWeights/further dataGross vehicle weight rating Kerb weight Max. trailer load, braked Turning circle Tank capacity Drag coefficient 1,850 kg 1,341 kg 1,200 kg 10.9 m 55 litres 0.34 cd6Interior dimensions and volumesmm1,686 mm334 mm684 mm1,471 mm1,007948 m m884 mms498_328Interior dimensions and volumesInterior length Luggage compartment volume Height of open rear lid Height of load sill Height of luggage compartment aperture Width of luggage compartment aperture 1,686 mm 250 litres 1,471 mm 684 mm 334 mm 884 mm Front headroom Headroom – 2nd seat row Knee room – 2nd seat row 1,007 mm 948 mm **Sufficient knee room can only be obtained by reducing the knee room of the first seat row.7BodyBody structureOverviewThe body of the Golf Cabriolet 2012 is based on the Golf 2009. The outer panels, the A-pillars and the rear bulkhead are new and were specially developed for the Golf Cabriolet 2012. Body parts from the Scirocco and from the Audi A3 Cabriolet have also been used.s498_005Explanation of colourss498_021 Parts specific to Golf Cabriolet 2012 Parts from Golf 2009 Parts from Scirocco Parts from Audi A3 CabrioletCavities and anti-drum measuresThe body cavities are acoustically sealed with insulation foam. The insulation is glued in or inserted in an unexpanded state during body assembly. It then expands to fill the respective cavities once it is exposed to heat during processing.8Rear bulkheadRoll-over protection systemBolted connectionsThe fixed rear bulkhead comes in a single piece and has been specially designed for the Golf Cabriolet 2012. It has integrated reinforcements for securing the rear seat bench and holds the roll-over protection system. The red markings in the illustration show the bolted connections between the roll-over protection system and the rear bulkhead (four on each side).Rear bulkheads498_020Reinforced A-pillarsThe design of the A-pillar is based on the A-pillar from the EOS. In crashes or if the car rolls over, the Apillar of a cabriolet needs to withstand considerably greater forces than a vehicle with a conventional roof. Sheet thicknesses of 2 mm are used to meet these tougher requirements. Thermoformed, ultra-high-strength sheet metals are used on the inside of the A-pillar. In crashes, they provide support on the inside, i.e. the “pressure side”. A reinforcing piece on the outside at the bending zone provides additional stability and guarantees safety in the passenger compartment should the vehicle “roll over”.A-pillar (ultra-high-strength)Reinforcement in bending zones498_0229BodyRoof cross member and bulkheadThe roof cross member is designed for roll-over and has an integrated fitting for the convertible roof locking mechanism. The windscreen cross member taken from the Scirocco forms the bulkhead and is connected to the A-pillars. Roof cross members498_024 Windscreen cross member/ bulkheadBody side panelThe body side panel incorporates the sheet metal sill and consists of an inner and outer panel. The inner panel is made up of several parts while the outer panel is single-piece.Inner panels498_026Outer panel10B-pillar and heel plate areaThe concept for the B-pillar has been taken from the Audi A3 Cabriolet. The raised support of the heel plate to the B-pillar helps improve side collision performance. The front seat belt mounting has been integrated into the B-pillar.s498_028 B-pillar Support11BodyDoors and window regulatorsDoor frameAssembly flap Guide railsIn addition to the usual side storage compartments, the doors have a holder for 1.5 -litre water bottles and a compartment for the high-visibility waistcoat. The functional components for the window regulators are connected directly to the door structure. This means that assembly carriers are not used. The adjustment concept for the window regulators is the same as for the EOS.s498_280 Motor with Bowden cables LockSide panel trim (rear)The whole side trim panel is covered with foam sheet along the window sill. There is a storage compartment on the left-hand side. The mountings for the optional windbreak have also been integrated into the side trim panel.Windbreak mountingss498_282 Stowage compartment12Access to hydraulic pump First-aid boxLoad-through hatchLuggage compartment with load-through hatchThe luggage compartment volume of 250 litres is available both when the convertible roof is open and when it is closed. There is a cover in the side luggage compartment trim via which you can access the hydraulic pump for emergency operation of the convertible roof. There is a facility for securing a first aid box to the side trim of the luggage compartment (Germany only).s498_284 Luggage compartment floor (toolkit and spare wheel underneath) 2nd side accessWhen the rear seat backrests are folded forward, the luggage compartment also has a load-through hatch that reaches over the rear seat bench. The loadthrough hatch is 526 mm wide and 381 mm high. Reinforced hinges Insert partsRear lidThe rear lid is made up of an inner and an outer panel. Reinforcements are welded to the inner panel. The reinforced hinges connect the hinge bolting points to the bolting points for the rubber buffers. The insert parts that form the assembly openings for the lights are welded to them. The lock reinforcement is manufactured as a drawn part. The outer panel is fitted over it. The rear lid has an electrical release. There is no mechanical lock cylinder since manual release is possible when the power is disconnected by means of a Bowden cable.Lock reinforcements498_28613BodyRear lid manual release mechanismThe rear lid does not have a mechanical lock cylinder. If the Golf Cabriolet has a flat battery, the rear lid can be unlocked manually via a Bowden cable. The Bowden cable runs from the lock in the rear lid via the hinge along the hydraulic pump past the B-pillar and to the door frame on the driver's door. In the door frame, the Bowden cable ends with a loop that protrudes from the frame metal. The loop is hidden by a plastic cover that can be levered off with the key. Pull the loop to release the lock in the rear lid mechanically.s498_288 Bowden cable LockThe luggage compartment cannot be opened without the vehicle key if the vehicle battery is flat. First the driver's door needs to be opened mechanically with the key via the lock cylinder so that you can access the Bowden cable for the manual release mechanism in the door frame.s498_230 Bowden cable Loop behind cover14Floor panelMember for sill panel areaThe members in the sill panel area increase the stiffness of the whole body and thus improve occupant safety in side collisions. They provide additional body reinforcement in the areas where the diagonal struts are connected.Aluminium engine shieldTogether with the assembly holder, the aluminium engine capsule reduces the relative movement between the front subframe and the ends of the front longitudinal members.Diagonal strutsThe front and rear diagonal struts increase the torsional stiffness of the body and minimise the torsional oscillation and vibrations that are typical of cabriolets.SubframeThe subframe increases the stiffness of the body and reduces its vibrations. It is directly connected to the spare wheel well.Aluminium engine shield Members for sill panel areas498_029 Diagonal struts Subframe15BodyInteriorThe proven technology of the Golf 2009 is used for the whole front section including the cockpit and the dash panel. In contrast to the Golf 2009, the retaining clips from the Scirocco are used to secure the cockpit trim in the Golf Cabriolet 2012. The rear seat backrest can be folded down to use the load-through hatch in the luggage compartment.s498_02316Centre consoleThe basic version of the centre console has a storage compartment and a drink holder for 1.5-litre bottles. A taller version of the centre console with an armrest is available as an option (see illustration). The Golf Cabriolet 2012 comes with a 12 V socket as standard. The switch for operating the convertible roof is located next to the handbrake lever as in the EOS.s498_025 Centre console with armrestLumbar support adjustmentFront seatsThe manually adjusted 8-way front seats in the Golf Cabriolet 2012 have: • • • • • •s498_222Longitudinal adjustment and height adjustment Backrest tilt adjustment Lumbar support adjustment Integrated head-thorax airbag Whiplash-optimised head restraint system (for Euro NCAP 5 stars) Easy-EntryWindbreakThe windbreak is available as an optional accessory. It minimises wind buffeting in the interior while the car is travelling. The mountings are integrated into the side trim. Once the windbreak has been installed, passengers can no longer be seated on the rear seats.s498_20017Electrohydraulic Convertible RoofOverview of convertible roof designThe Golf Cabriolet 2012 has a fully automatic, fabric convertible roof with heated glass rear window. The convertible roof is operated by an electrohydraulic system with an automatic, electric motor-operated locking/ release mechanism. The convertible roof is permanently fastened to the body structure in the area of the C-pillar. When closed, it is securely locked to the roof cross member. When the convertible roof is open, it is folded into a z-shape on top of the luggage compartment. For the first time, the convertible roof can also be operated while the vehicle is travelling at slow speeds up to 30 km/h. The structure of the convertible roof is shown in three layers for better understanding: • • • Convertible roof cover with insulation and rear window Convertible roof frame with electrohydraulic convertible roof mechanism Headliner123s498_307 The convertible roof for the Golf Cabrio with the three layers: convertible roof cover with insulation and rear window (1), convertible roof frame with electrohydraulic system (2) and convertible roof headliner (3)18Convertible roof coverThe convertible roof cover consists of the convertible roof canvas and the convertible roof insulation that is connected to it. The cover is made up of one centre and two side panels. The convertible roof canvas has three layers. The outer layer is made from a polyacrylic fabric, the middle layer from synthetic rubber and the inner layer from polyester. All layers are permanently fastened to each other. The insulation also has three layers with outer layers made from polyester fleece and an inner layer of foam. Together with the improved sealing concept in the area of the doors and the roof cross member, this convertible roof cover concept improves the noise and heating comfort in the passenger cell. The convertible roof cover is fastened to the convertible roof frame with fabric-retaining strips. This method prevents excessive ballooning of the convertible roof on the road. The two lengthways seams on the convertible roof cover are designed so that they function as rain gutters and drain off rainwater in a longitudinal direction. This function is supported by round cord embedded in the side panels. The heated rear window made from single-pane toughened glass is bonded to the convertible roof cover during production by means of high-frequency welding.1s498_306324Convertible roof cover with insulation (1) and heated rear window (2) and fabric retaining strips (3) on convertible roof frame (4)19Electrohydraulic Convertible RoofConvertible roof mechanicsThe electrohydraulic convertible roof mechanism includes the folding convertible roof frame with the main pillars that fold at four joints. In addition, the convertible roof mechanism comprises the electrohydraulic convertible roof operating system and the electrical convertible roof locking mechanism in the front bracing hoop along with the roof cross member.Convertible roof frameThe convertible roof frame is made up of the following components: the two main mountings on the left and right the two main pillars with moving fabric retaining brackets the left- and right-hand main guide elements the side roof frame the front bracing hoop the control elements the bracing hoops the rear window guide elementsBracing hoop 3 Bracing hoop 4 Bracing hoop 5Bracing hoop 2 Front bracing hoops498_309Main pillar with roof frame, control elements, main guide elements and sealing stripsRear window guide elementMain mounting20The movement of the convertible roof frameEach main pillar has four joints and is connected to the body via the main mounting. The hydraulic cylinders are on the main mountings. The linear movement of the hydraulic cylinder is converted into the pivoting and folding movement of the convertible roof via the main guide elements and the control elements.Main mounting Hydraulic cylinder s498_308 Main mounting with hydraulic cylinderThe arrangement of joints allows the convertible roof to be folded into a Z-shape and placed on top of the luggage compartment. The area of the front bracing hoop has been made large enough so that it covers the opened convertible roof almost completely and thus protects both the rear window and the convertible roof cover. The convertible roof on the Golf Cabrio 2012 opens in approx. 9 seconds and closes in approx. 11 seconds.When the convertible roof is opened, the front bracing hoop stays at the same angle almost over the complete path of the roof since the roof frame forms a parallelogram. The rear window guide elements ensure that the rear window is guided towards the luggage compartment as the convertible roof opens until it reaches its end position with the outside of the window facing downwards under the front bracing hoop. The rear window is then fully protected by the front bracing hoop.Formation of parallelogramFront bracing hoop when convertible roof is closed Front bracing hoop when convertible roof is open s498_31121Electrohydraulic Convertible RoofElectrohydraulic systemSystem overviewThe electrohydraulic system for operating the convertible roof consists of the following main components: • • • • • • • • the convertible roof actuation control unit J256 the convertible roof actuation button E137 in the centre console the convertible roof operation warning lamp K215 in the control unit in dash panel insert J285 the hydraulic system with the convertible roof actuation hydraulic pump V118 the convertible roof front switch F202 in the left-hand main mounting the convertible roof stowed switch F171 in left-hand main mounting the convertible roof lock with convertible roof lock motor V223, the convertible roof latch open switch F294 and convertible roof latch closed switch F295 the left latch switch for convertible roof F169 and right latch switch for convertible roof F170 in the roof cross memberAutomatic convertible roof locking mechanismConvertible roof hydraulicss498_312 The electrohydraulic system is connected to the data bus network via the convenience CAN data bus (a) and via the data bus diagnostic interface J533. The control unit also receives the necessary additional signals, for example, the outside temperature (measured by ambient temperature sensor G17) and the speed signal via the CAN data bus.22Data bus communicationThe convertible roof actuation control unit communicates with the numerous other control units via the convenience CAN data bus and the data bus diagnostic interface. This allows, for example, the side windows to be automatically dropped down slightly to make it easier for the convertible roof to move when it is opened. Then, when it is closed again, the side windows are raised to fit perfectly into the window seals. This requires that the convertible roof operation control unit instructs the door control units to activate the window regulator motors accordingly. The convertible roof control system receives the speed signal required for roof operation via the powertrain CAN data bus and the diagnostic interface of the ABS control unit.as498_082KeyE137 E586 F169 F170 F171 F202 F294 F295 G17 J104 J255 J256 J285 J301 J386 J387 Convertible roof actuation button Window regulator button Left latch switch for convertible roof Right latch switch for convertible roof Convertible roof stowed switch Convertible roof front switch Convertible roof latch open switch Convertible roof latch closed switch Ambient temperature sensor ABS control unit Climatronic control unit Convertible roof actuation control unit Dash panel insert control unit Air conditioning system control unit Driver door control unit Front passenger door control unit a J388 J389 J519 J533 J623 K215 V118 V223 Door control unit, rear left Door control unit, rear right Onboard supply control unit Diagnosis interface for data bus Engine control unit Convertible roof operation warning lamp Convertible roof actuation hydraulic pump Convertible roof lock motor Sensor/input Actuator/output Powertrain CAN data bus Convenience CAN data bus Combi CAN data bus23Electrohydraulic Convertible RoofHydraulic systemConvertible roof frame with convertible roof cover Hydraulic cylinder on right hand main mounting s498_337 Hydraulic cylinder on lefthand main mounting Hydraulic pump V118 in pump housingHydraulic system set-upThe hydraulic system consists of the following components, among others:1 2 3 4 5 6 7 8 9 Left- and right-hand hydraulic cylinders Return restrictor Emergency operation mechanism Non-return valves (pressure controlled) Control lines Hydraulic pump V118 Shuttle valve Reservoir Pump housing 2 3 5 4 4 5 6 7 8 9 2 1 124s498_313This is how it works:When a convertible roof procedure is started, the convertible roof actuation control unit activates the hydraulic pump. The direction of rotation of the pump and the position of the shuttle valve in the pump decide whether the hydraulic cylinders extend or retract. If the hydraulic cylinders are extended, the convertible roof will open. When the hydraulic cylinders are retracted, the convertible roof closes. The shuttle valve ensures that hydraulic fluid can be fed into or flow out of the reservoir when the rotation direction of the pump is switched by the control unit. Two control lines each connect one of the two pressure-controlled non-return valves to the hydraulic circuit for the opposite direction of travel. If the pressure side changes with the direction of rotation of the pump, the assigned non-return valve is held open from there by the respective control line so that hydraulic fluid can flow from the cylinder to the pump. The non-return valves are closed when not activated. Thanks to this hydraulic self-blocking system, the system pressure is maintained and the convertible roof remains in the position it reached.11 2 3 3 2 4 s498_315 6 7 2 3 5 4 5 6 7 s498_314Hydraulic cylinder Control line Non-return valve Hydraulic pump Convertible roof actuation control unit Shuttle valve Reservoir Supply Return Depressurised25Electrohydraulic Convertible RoofConvertible roof actuation hydraulic pump V118Task and installation location The hydraulic pump for convertible roof actuation is located behind a flap on the left of the luggage compartment. It is connected to the hydraulic system via plastic hydraulic lines and operates the hydraulic cylinders when the convertible roof is actuated.Housing Emergency operation screws498_303Convertible roof actuation hydraulic pumpHow it works By switching the rotation direction of the pump electrical drive, the delivery direction is reversed thus setting the direction of the convertible roof travel.Effects of failure If a fault occurs in the pump during convertible roof operation, it will only be possible to close the convertible roof manually after turning the emergency operation screw. Automatic opening or closing is no longer possible (see emergency operation).Convertible roof stowed switch F171Installation location and task The convertible roof stowed switch is a Hall sender. It is located on the left-hand main mounting of the convertible roof frame. The convertible roof actuation control unit uses the signal from F171 to detect when the convertible roof has reached its end position on top of the luggage compartment.s498_316Effects of failure Without the signal from F171, the convertible roof actuation control unit cannot establish whether the convertible roof has reached its end position on top of the luggage compartment. The system switches to fault mode and the convertible roof can only be closed manually. The emergency operation procedure must be performed in this case.26Convertible roof front switch F202Installation location and task The convertible roof front switch is also a Hall sender. It is located on the base of convertible roof in the lefthand main mounting. The convertible roof actuation control unit uses the signal from F202 to detect when the convertible roof has reached its end position on the roof cross member and when the automatic locking procedure can be initiated.s498_331Effects of failure Without the signal from F202, the convertible roof actuation control unit cannot establish whether the convertible roof has docked with the roof cross member and reached its end position. The system switches to fault mode and the convertible roof can only be closed manually. The emergency operation procedure must be performed in this case. A maximum of 25 seconds are available for the convertible roof to reach one of the two end positions (open/ closed) each time it is operated. This time limit applies from the moment the convertible roof actuation button (E137) is pressed regardless of the convertible roof position. If this time limit is exceeded, the convertible roof actuation control unit will stop the operation.27Electrohydraulic Convertible RoofConvertible roof lockInstallation location and taskThe electrical convertible roof locking mechanism is located in the front bracing hoop under a plastic cover. It fastens the closed convertible roof securely to the roof cross member.Locking hookCarrier plate with locking mechanism Front bracing hoopLocking hooks498_310 Electrical convertible roof locking mechanism in front bracing hoopDesignA carrier plate holds the electric drive motor, the gearbox connected to the locking linkage and two microswitches with a switch actuator, which belong to the locking recognition system. Linkages are used for the connections to the two locking hooks. During locking, the locking hooks engage in corresponding catches in the roof cross member and thus fasten the convertible roof securely to the front body structure.Gearbox for locking mechanism Rotating switch actuatorMotors498_220Convertible roof lock switch28This is how it works:The convertible roof lock motor V223 is activated by the convertible roof actuation control unit J256 once the convertible roof has reached its end position on the roof cross member and the control unit detects this position. This is done using the convertible roof front switch F202 on the main mounting. The rotation direction of the convertible roof lock motor is reversed to open or close the locking mechanism. A maximum of 4 seconds activation time is allowed in the control unit for the travel between the locked (F295) and unlocked (F294) positions to protect the system against overloading if the convertible roof movement is obstructed. If this time is exceeded, a system emergency run is activated. The signal from the switches F169 and F170 “Convertible roof locked at front” indicates the end of the convertible roof closing procedure. If this signal is not issued, the system will continue to ask the operator to close the convertible roof. (The hydraulic pump has already been switched off after the signal from F202.)Locking hook in the front bracing hoop (a), locking hole in the roof cross member (b) s498_333The convertible roof control system can only clearly determine whether a convertible roof operation has been successfully completed and the convertible roof is in one of the two safe positions “Convertible roof closed and locked to the roof cross member” or “Convertible roof open and placed on top of luggage compartment” if it has received all information from the switches in the main mounting and from the convertible roof locking mechanism.29Electrohydraulic Convertible RoofConvertible roof latch open switch F294 and latch closed switch F295Installation location and task The two microswitches are located on the carrier plate with the locking mechanism in the front bracing hoop. The switches are operated by a rotating switch actuator via two angled levers. When the motor V223 starts running, the switch actuator rotates and actuates one of the two angled levers once one of the end positions is reached. The lever then opens the associated switch. If the actuator moves in the opposite direction, the other angled lever will be actuated and the second switch is thus opened while the first switch is closed. The end position of the locking hook corresponds with one end position of the switch actuator so that only one of the two switches is opened by the angled lever at one time with “Hook in unlocked position” or “Hook in position locked”. This allows the convertible roof lock control unit to determine whether the locking hooks are in one of the two end positions or in-between.DriveSwitch actuator Angled leverSwitch “Convertible roof unlocked” position“Convertible roof locked” positionEffects of failure Without the signal from the two switches, the convertible roof actuation control unit cannot determine whether the locking hooks are in one of the two end positions. The system switches to fault mode and the convertible roof can only be closed manually. The emergency operation procedure must be performed in this case.30s498_318s498_317Left F169 and right F170 latch switch for convertible roofInstallation location and taskF169 F170The switches are on the left and right in the roof cross member on the locking holes. They are operated by the locking hooks when they hook into the locking holes on the roof cross member. These two switches allow the convertible roof control system to determine whether the two locking hooks, which are already in the end position “closed” according to the signal from F294 and F295, have actually managed to hook into the locking holes on the roof cross member. Only then is the convertible roof securely fastened to the roof cross member on both sides of the vehicle and in a safe position so that the convertible roof operation can be completed.s498_332Locking hookRoof cross member SwitchFront bracing hoop Locking hook and switch before lockings498_336Roof cross memberEffects of failure Without the signal from F169 and F170, the convertible roof actuation control unit cannot Front bracing hoop s498_335 establish whether the convertible roof is connected to the roof cross member by the locking hooks on both Locking hook and switch after locking sides of the vehicle. Since the control unit J256 cannot determine whether F169 and/or F170 have been actuated or not, it will enter the fault “Convertible roof front lock switch, implausible signal” in the fault memory after a set maximum time has expired. The system switches to fault mode and the convertible roof can only be closed manually. The emergency operation procedure must be performed in this case.31Electrohydraulic Convertible RoofFurther electrical componentsConvertible roof actuation control unit J256Installation location and task This control unit is located in the luggage compartment on the left next to the convertible roof actuation hydraulic pump V118. It controls the whole electrohydraulic system for the convertible roof in interaction with other control units within the Golf Cabriolet CAN data bus network. It communicates, for example, both with the ABS control unit on the powertrain CAN data bus and with the door control units and the air conditioning system control unit on the convenience CAN data bus. Faults in the roof control system electrics are stored in the fault memory of the convertible roof actuation control unit.Emergency operation screw on hydraulic pumpConvertible roof actuation control unit J256Emergency operation handle s498_350Effects of failure If the control unit is faulty, it will only be possible to open and close the convertible roof manually. The emergency operation procedure must be performed in this case.Further control unit functions The system has a so-called “Tamper protection” function to protect the hydraulic pump and electric locking mechanism against overheating and damage due to constant running. It is activated if the convertible roof is operated without interruption for a long period (approx. 2 minutes). In this case, the “tamper protection” function will block convertible roof operation for approx. 10 minutes if the convertible roof is closed. If the convertible roof does not reach the “closed” status after approx. 2.5 minutes of constant operation, the convertible roof operation will be stopped immediately and can only be moved to the rear, open end position. The convertible roof will remain in the position reached without the button being pressed again. The message “Temperature too high, convertible roof” will appear on the dash panel insert display. It is then only possible to operate the convertible roof again after it has been disabled for 25 minutes. The convertible roof operation warning lamp K215 in the dash panel insert will flash as a warning and indication that convertible roof operation has been disabled by the tamper protection function.32Convertible roof actuation button E137Installation location and task The convertible roof actuation button is located in the centre console. It has two switching directions. Pressing and holding opens the convertible roof. Pulling and holding closes the convertible roof. If you let go of the button during a convertible roof operation, the roof operation will stop and the convertible roof will stop in the position reached. s498_319 Operating the button again resumes the convertible roof operation according to the direction you move it in. If, after the opening procedure, you hold the button for a further 3 seconds, the side windows will be lowered completely. If you hold the button or pull it again after the closing procedure, the side windows will be raised completely. There is an additional button within the button. This is the central window regulator button E586. It can be used to operate all side windows at the same time (manual/automatic run).Effects of failure Without the signal from the convertible roof actuation button, automatic convertible roof operation is only possible using the convenience function via the door lock.Convertible roof operation warning lamp K215Installation location and task The warning lamp is located in the dash panel insert. During convertible roof operation, the warning lamp is constantly illuminated and extinguishes once the convertible roof operation has been completed. If the convertible roof has not reached one of the two end positions or there is a fault in the system when the convertible roof actuation button is held, K215 will flash.s498_32033Electrohydraulic Convertible RoofConvertible roof operationThe convertible roof can be opened or closed if the required system conditions are met. If operation of the electrohydraulic convertible roof is not possible, the convertible roof can also be moved manually to one of the two end positions using the emergency operation system (see page 38). Special features during roof operation If the convertible roof has already been unlocked for opening, this convertible roof opening procedure can also be completed at speeds greater than 30 km/h. It is only possible to open or close the convertible roof via the door lock by means of mechanical operation with the key once you have removed the cylinder cover on the driver-side door handle. If the convertible roof is moved in opposite directions 2-3 times between the positions “Convertible roof at front” or “Convertible roof at rear”, the control unit will no longer be able to clearly identify the convertible roof position. The convertible roof operation is interrupted and the driver is asked to move the convertible roof to the end position “Opened”. When the convertible roof is closed, the locking hooks are only moved to the position “unlocked” after approx. four seconds to avoid collisions with the backrest console of the rear seats.-Opening convertible roofRequirementsVehicle stationary or travelling at speed 30km/h with convertible roof in »closed« position Ignition is switched on Convertible roof operation not requested via convenience opening/closing Outside temperature is -10 °C Rear lid is closed Onboard supply voltage is 11.4 V with convertible roof fully open or closed; 10 V is required from an intermediate position Hydraulic system and electrical convertible roof locking mechanism are not overheated (tamper protection is not active) The convertible roof actuation button is held during whole convertible roof operation34s498_321ProcedureThe button for convertible roof actuation is pressed and held down during the whole convertible roof operation. The convertible roof operation warning lamp lights up and stays on. The side windows are automatically lowered to a preset level (automatic drop-down position). Windows that are in or below the automatic drop-down position, are not lowered. If all side windows are below the automatic drop-down position, the convertible roof actuation control unit will unlock the convertible roof from the roof cross member. The rear window heating is deactivated and operation of the rear lid is blocked for the duration of the convertible roof operation. Once the locking hooks have reached the “unlocked” position, the hydraulic pump starts to run and the convertible roof moves to the rear folding itself together in the process. In the meantime, the locking hooks are returned to the “locked” position. The convertible roof stowed switch confirms that the roof has reached the end position on top of the luggage compartment and the hydraulic pump stops. The warning light goes out and use of the rear lid is enabled again. The side windows close. In this convertible roof position, the trim on the front bracing hoop covers the folded convertible roof and protects the convertible roof cover and the rear window.35Electrohydraulic Convertible RoofClosing convertible roofIf the control unit recognises the convertible roof status »Convertible roof open« or the convertible roof is in an intermediate position because, for example, you have let go of the convertible roof actuation button, the convertible roof can be closed by pulling and holding the button again.RequirementsVehicle is stationary or is travelling at speed 30 km/h Ignition is switched on Convertible roof operation not requested via convenience opening/closing Rear lid is closed Onboard supply voltage is 11.4 V with convertible roof fully open or closed; 10 V is required from an intermediate position Hydraulic system and electrical convertible roof locking mechanism are not overheated (tamper protection is not active) The convertible roof actuation button is held during whole convertible roof operations498_323ProcedurePull and hold the convertible roof actuation button during the whole convertible roof operation. The convertible roof operation warning lamp lights up and stays on. The side windows are moved to the automatic drop-down position regardless of their current position to make convertible roof operation possible. Use of the rear lid is blocked again for the duration of the convertible roof operation.36The convertible roof actuation control unit activates the hydraulic pump in the opposite direction to opening operation. The convertible roof unfolds itself while moving to the front towards the roof cross member. After approx. four seconds of convertible roof operation, the locking hooks move to the position “unlocked”. The convertible roof front switch detects when the front bracing hoop docks onto the roof cross member and sends a signal to the control unit. The control unit switches the hydraulic pump off. The convertible roof has reached its end position. The locking hooks are moved to the “locked” position and thus securely fasten the convertible roof to the roof cross member. The side windows close completely. The rear window heating is enabled again and the convertible roof operation warning lamp goes out. The convertible roof is closed.Convenience operationThe convertible roof can also be opened or closed via the door lock. The cap on the driver door lock needs to be removed so that you can insert the vehicle key into the lock cylinder. In contrast to the operating conditions for opening the convertible roof with the button, the ignition key may not be inserted in the ignition lock and the ignition must be switched off in this case. Furthermore the convertible roof actuation button may not be pressed. The vehicle must first be unlocked before the convertible roof can be opened. If the key is then turned once again in the “unlock” direction within approx. 2 seconds and held there, the procedure for opening the convertible roof will start. You first need to lock the vehicle before closing the convertible roof. If you turn the key again in the “lock” direction within approx. 2 seconds and hold it there, the procedure for closing the convertible roof will start.37Electrohydraulic Convertible RoofEmergency operationIf the convertible roof cannot be operated with the electrohydraulic system due to a fault, the roof can be operated manually. This requires three steps : the hydraulic system needs to be switched to emergency operation at the hydraulic pump the convertible roof locking mechanism on the roof cross member needs to be released manually the roof must be folded or unfolded to the respective end position by handThe following section describes how to open the convertible roof manually. It is closed in the reverse sequence.Please note the information on manual emergency operation of the convertible roof in the owner's manual for the vehicle.Recommended measures for emergency operationapply the handbrake lower all side windows turn the ignition off (terminal 15 »off«) remove the ignition key (terminal S »off«) close the rear lids498_324 Emergency operation screw and indication of rotation direction on housing of convertible roof actuation hydraulic pumpSwitching the hydraulic system to emergency operationThe hydraulic system is designed so that it holds the convertible roof in its current position when you let go of the convertible roof button (self-locking system). The emergency operation screw on the hydraulic pump must be loosened to override this self-locking system. This connects the hydraulic circuits and by-passes the self-locking system. Procedure The emergency operation screw can be accessed by removing the cover in the luggage compartment. Observe the direction of rotation on the pump housing before loosening the screw by approx. half a turn.38Manually unlocking the convertible roof at the roof cross memberThe electrical unlocking system for the convertible roof is also not available if there is a fault. Therefore the locking hooks need to be moved manually to the “unlocked” or “locked” position.Procedure In the vehicle interior, use a suitable screwdriver to remove the rectangular cover from the locking mechanism trim near the front bracing hoop. Behind the cover, you will see the socket for the emergency operation handle. The emergency operation handle is stored behind the trim on the left of the luggage compartment. Fit the emergency operation handle into the guide pins in the socket and lock it by tightening the screw that is built into the handle.s498_325 Cover cap Socket for emergency operation handleTurn the handle clockwise to release the convertible roof locking hooks from the cross member. If you turn it anti-clockwise, the locking hooks will lock the convertible roof to the roof cross member as long as the front bracing hoop has docked with the roof cross member correctly.Manually stowing the convertible roof in the open positionIf possible, a second person should help close or open the convertible roof to prevent the convertible roof and the convertible roof mechanism becoming jammed. Once the convertible roof has reached its end position, the emergency operation screw on the hydraulic pump must be returned to its original position so that the two hydraulic circuit halves are separated again. This removes the pressure equilibrium between the two halves of the hydraulic circuit. The self-locking system for the convertible roof is engaged and prevents the roof moving.39Occupant ProtectionRoll-over protection systemOverview and designTogether with the A-pillars and the roof cross member, the roll-over protection system has the task of creating a survival space for the vehicle occupants if the vehicle rolls over. It is built into the rear bulkhead as a module behind each rear seat. The main components of the roll-over protection module are spring-loaded, sturdy detent rails and an assembly frame with rail guides and a lock with trigger mechanism. Covers on the trim panel behind the head restraints conceal the roll-over protection system from above.How it worksThe roll-over protection system is triggered together with the corresponding airbags by the airbag control unit when a defined accident situation is detected. The roll-over protection system is deployed: • • in severe front, side and rear collisions (high-speed crashes) when the vehicle rolls over Assembly frame Deployed detent railThe roll-over protection system is triggered by the electronic ignition of a pyrotechnic charge that releases the mechanical lock on the detent rail. The detent rails are extended within milliseconds by the spring tension and form a safe roll-over protection system together with the A-pillars. The covers in the rear bulkhead trim are pushed out and up by the detent rails.s498_32640AirbagsDriver and front passenger airbagThe Golf Cabriolet 2012 features the latest in occupant protection. The driver and front passenger airbags come from the Golf A6. The head-thorax airbags are located in the backrests of the driver and front passenger seats under the front of the seat cover. In a collision, they inflate between the occupant and penetrating vehicle structure. They have been improved in terms of their location under the backrest cover. A knee airbag comes as standard for the driver.Knee airbag (only driver)Head-thorax airbagss498_031Side impact protectionThe doors feature side impact protection as standard. The diagonal arrangement of the side impact protection members increases the area protected. This means that, in a side collision, the side impact protection system is hit even at different crash heights. It absorbs the energy of the impact and transfers it to the side of the body.s498_038 Side impact protection cross member41Engines1.2 l 77 kW TSI engine with turbochargerThis engine is available in a standard and in a BlueMotion Technology version. The BlueMotion Technology version is equipped with a start/stop system and uses energy recovery. Technical features • • • • • Homogenous mode (Lambda 1) Switchable coolant pump A separated, service-friendly lightweight timing case with covers made of plastic and magnesium Turbocharger module with electrically operated waste gate flap control Crankcase breather and ventilation system with oil separation facility integrated in cylinder block and cylinder head Ignition transformers498_045•You will find further information in self-study programme no. 443 “The 1.2 l 77kW TSI Engine with Turbocharger”. Torque and output diagramCBZB 4-cylinder inline engine 1,197 cm3 71 mm 75.6 mm 2 10 : 1 77kW at 5,000rpm 175 Nm at 1,550 to 4,100 rpm Simos 10 Super unleaded RON 95 Three-way catalytic converter with one upstream broadband Lambda probe and one downstream steptype Lambda probe EU5120 100 80 60 40 20 1000 3000 [rpm] 5000 7000 50 40 30 20 10 0 [Nm] 200 180 160 140 [kW] 90 80 70 60Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Max. output Max. torque Engine management Fuel Exhaust gas aftertreatmentExhaust emissions standards498_040421.4 l 90 kW TSI engine with turbochargerThis engine has already been used in other vehicles and has now been transferred to the Golf Cabriolet. Technical features • • • • • • • Homogenous mode (Lambda 1) Stratified high-pressure start Turbocharger with waste gate Intake manifold with charge air cooler with coolant flow Regulated duo-centric oil pump Demand-based fuel system High-pressure fuel pump with integrated pressure limiting valves498_041You will find further information in self-study programme no. 405 “1.4l 90kW TSI Engine with Turbocharger”. Torque and output diagramCAXA 4-cylinder inline engine 1,390 cm3 76.5 mm 75.6 mm 4 10 : 1 90kW at 5,000rpm 200 Nm at 1,500 to 4,000 rpm Bosch Motronic MED 17.5.5 Super unleaded RON 95 Three-way catalytic converter with one upstream broadband Lambda probe and one downstream steptype Lambda probe EU525 0 1000 3000 [rpm] 5000 7000 10 0 125 100 75 50 50 40 30 20 [Nm] 225 200 175 150 [kW] 90 80 70 60Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Max. output Max. torque Engine management Fuel Exhaust gas aftertreatments498_047Exhaust emissions standard43Engines1.4 l 118 kW TSI engine with dual-chargingThis engine has been adopted from the Golf without modifications. Technical features • • • • • • • • • Homogenous mode (Lambda 1) Stratified high-pressure start Turbocharger with waste gate Clutch-operated mechanical supercharger Air/charge air cooling Dual circuit cooling system Regulated duo-centric oil pump Demand-based fuel system High-pressure fuel pump with integrated pressure limiting valves498_049You will find further information in self-study programme no. 359 “1.4l TSI Engine with Dual-charging”.Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Max. output Max. torque Engine management Fuel Exhaust gas aftertreatment CAVD 4-cylinder inline engine 1,390 cm3 76.5 mm 75.6 mm 4 10 : 1 118 kW at 5,800 rpm 240 Nm at 1,500 to 4,500 rpm Bosch Motronic MED 17.5.5 Super unleaded RON 95 Three-way catalytic converter with one upstream broadband Lambda probe and one downstream steptype Lambda probe EU5 Torque and output diagram[Nm] 260 240 220 200 180 160 140 120 100 80 1000 3000 [rpm] 5000 7000 [kW] 120 100 90 80 70 60 50 40 30 20s498_053Exhaust emissions standard442.0 l 155 kW TSI engine with turbochargerThis engine has already been used in the Golf GTI and the Passat 2011 and corresponds to a great extent with the 2.0l 147kW TSI engine. This engine comes exclusively with the dual clutch gearbox. Technical features • • • • The turbocharger pressure actuator cannot be exchanged. Volumetric flow-controlled external gear oil pump Two balancer shafts High-performance charge air coolers498_051You will find further information in self-study programme no. 401 “1.8l TFSI 16v 118kW engine”.Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Max. output Max. torque Engine management Fuel Exhaust gas aftertreatment CCZB 4-cylinder inline engine 1,984 cm3 82.5 mm 92.8 mm 4 9.6 : 1 155 kW at 5,300 to 6,200 rpm 280 Nm at 1,700 to 5,200 rpm Bosch Motronic MED 17.5 Super unleaded RON 95 Broadband Lambda probe upstream of close-coupled starter catalytic converter, step-type Lambda probe downstream of catalytic converter EU5 Torque and output diagram[Nm] 320 300 280 260 240 220 200 180 160 140 1000 3000 [rpm] 5000 7000 [kW] 180 160 140 120 100 80 60 40 20 0s498_044Exhaust emissions standard45Engines1.6 l 77 kW TDI CR engineThe further developed 1.6l TDI CR engine, which has already featured in the Passat 2011, is now available for the Golf Cabriolet 2012. Technical features • • Common rail injection system with piezo injectors Exhaust gas recirculation module with exhaust gas recirculation valve and cooler for exhaust gas recirculation. Plastic intake manifold without swirl flap adjustment Camshaft spur gear drive without backlash compensation High-pressure pump with gear-type fuel system pressurisation pump Electrical fuel system pressurisation pump in fuel tank• • • •s498_339You will find information on the design and function of the 1.6l TDI CR engine in self-study programme no. 442 “The 1.6ltr. 77kW TDI Engine with Common Rail Injection System”. Torque and output diagramTechnical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Max. output Max. torque Engine management Fuel Exhaust gas aftertreatment CAYC 4-cylinder inline engine 1,598 cm3 79.5 mm 80.5 mm 4 16.5:1 77 kW at 4,400 rpm 250 Nm at 1,500 to 2,500 rpm Simos PCR2.1 Diesel according to DIN EN 590 Exhaust gas recirculation, oxidation catalytic converter and diesel particulate filter EU5[Nm] 260 240 220 200 180 160 140 120 100 1000 3000 [rpm] 5000[kW] 90 80 70 60 50 40 30 20 10Exhaust emissions standards498_046462.0 l 103 kW TDI CR engineThe second generation 2.0l TDI CR engine has already been used in the Passat and Sharan. Both diesel engines for the Golf Cabrio are available in standard or BlueMotion Technology versions. Technical features • • Common rail injection system with solenoid valvecontrolled injectors Exhaust gas recirculation module with exhaust gas recirculation valve and cooler for exhaust gas recirculation. Intake manifold without swirl flap adjustment Electrical fuel system pressurisation pump in fuel tank Electrical supplementary fuel pump in fuel supply line• • •s498_207You will find further information on this engine in self-study programme no. 403 “The 2.0-ltr. TDI Engine with Common Rail Injection System” and in self-study programme no. 445 “The Sharan 2011”. Technical dataEngine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Max. output Max. torque Engine management Fuel Exhaust gas aftertreatment CFHC 4-cylinder inline engine 1,968 cm3 81 mm 95.5 mm 4 16.5:1 103 kW at 4,200 rpm 320 Nm at 1,750 to 2,500 rpm Bosch EDC 17 (common rail injection system) Diesel according to DIN EN 590 Exhaust gas recirculation, oxidation catalytic converter and diesel particulate filter EU5240 220 200 180 160 1000 3000 [rpm] 5000 60 50 40 30 20 260 70 300 280 90 80 Torque and output diagram[Nm] 320 [kW] 100s498_348Exhaust emissions standard47TransmissionEngine and gearbox combinationsPetrol engines1.2l 77kW engine CBZB 1.4l 90kW TSI engine CAXA 1.4l 118kW TSI engine CAVD 2.0l 155 kW TSI engine CCZB6-speed manual gearbox 0AJ 6F*6-speed manual gearbox 02S 6F*6-speed dual-clutch gearbox 02E 6F*7-speed dual-clutch gearbox 0AM 7F**5F = 5-speed front-wheel drive, 6F = 6-speed front-wheel drive, 7F = 7-speed front-wheel drive48Diesel engines1.6l 77kW TDI engine CAYC 2.0l-103kW TDI engine CFHC5-speed manual gearbox 0A4 5F*6-speed manual gearbox 02Q 6F*6-speed dual-clutch gearbox 02E 6F*49TransmissionOverview of manual gearboxesThe Golf Cabriolet 2012 uses the same gearboxes as the current Golf.Gearbox typeTechnical featuresFurther information• •6-speed manual geabox 0AJ 6F*• • • •Developed from 0AG gearbox SSP 237 modified for 1.4 l 90 kW TSI engine, spacing between output shaft SSP 306 and differential enlarged, sheet metal mount replaced by cast mount for higher torques, ground toothing Final drive reinforced Without speedometer sender CO2-optimised ratio Torque capacity up to 200 Nm5-speed manual gearbox 0A4 5F*• • • • •Developed from 02J Gearshift mechanism optimised Without speedometer sender CO2-optimised ratio Torque capacity up to 250 NmSSP 99 SSP 306• • • • •6-speed manual gearbox 02S 6F*Developed from 0A4 Longer shafts with additional bearings, additional gear pair, new longer aluminium housing cover Without speedometer sender CO2-optimised ratio Torque capacity up to 250 NmSSP 99 SSP 306• • • • •6-speed manual gearbox 02Q 6F*Developed from 02M gearbox Changes to selector shaft, selector forks with stops in housing, modified bearings Without speedometer sender CO2-optimised ratio Torque capacity up to 350 NmSSP 205 SSP 306*5F = 5-speed front-wheel drive, 6F = 6-speed front-wheel drive, 7F = 7-speed front-wheel drive50Overview of dual-clutch gearboxesThe dual-clutch gearboxes allow split-second, smooth gear changes. The dual-clutch gearboxes consist of two independently working gear train halves. Each gear train half is connected to a clutch. During a gear change, one clutch is opened while, at the same time, the other clutch closes.Gearbox typeTechnical featuresFurther information• • • • •6-speed dual-clutch gearbox 02E 6F*Hydraulic dual-clutch (two multi-plate wet clutches) Greater efficiency Robust and sporty like a manual gearbox The user-friendliness of an automatic gearbox when changing gear Torque capacity up to 350 NmSSP 308• • • • •7-speed dual-clutch gearbox 0AM 7F*Developed from 6-speed dual-clutch gearbox 02E In contrast to 02E, works with a dry dual-clutch Separate oil circuits for gearbox and mechatronics In contrast to 02E, electrical oil pump for hydraulics is regulated on demand by the control unit Torque capacity up to 250 NmSSP 39051Running GearOverview of running gearThe chassis of the Golf Cabriolet 2012 is based on the Golf 2009 chassis. The illustration shows you important standard and optional equipment for the new Golf Cabriolet 2012. Normal and sports chassis are available. DDC adaptive chassis control is available as an option.•Tyre Mobility Set as standard •Four-link rear axle, with bolted diagonal strut on subframe •Lightweight McPherson strut front axle with bolted diagonal strut on subframe •ESP generation MK60-EC system from Continental Teves with integrated sensor cluster and Hill Hold 52•Safety steering column (sheet metal version)•DCC adaptive chassis control, optional•Electromechanical power steering with double pinion, 3rd generation, with integrated steering angle sensor •s498_061Floor-hinged accelerator pedal, crash-optimisedYou will find information on the DCC adaptive chassis control in self-study programme 423 “The Golf 2009”. You will find further information on the DCC adaptive chassis control in self-study programme 406 “DCC Adaptive Chassis Control”.53Heating and Air ConditioningAir conditioningThree climate control systems are available for the Golf Cabriolet: a heating system, an air-conditioning system and the two-zone Climatronic system. The “ThermoTop V” and “ThermoTop Vlies” auxiliary heaters can be used depending on whether a diesel or petrol engine is fitted. The following table provides an overview and references to detailed descriptions.Technical features Heating and ventilation systemSSP no.:• •Mechanical rotary switch for temperature and air distribution Adjustment of temperature and air flaps via flexible shaftsSSP 471s498_072 Air-conditioning systems498_073• • • •One climate zone Electronic rotary switch for temperature and air distribution AC button for switching on and off Electrical adjustment of temperature and air flaps via control motors SSP 4932-zone Climatronic• • •s498_075 ThermoTop V auxiliary heaterDriver and front passenger each have own climate zone Control range of 18 °C-26 °C with temperature preselection Dual operation of zones (DUAL button)SSP 493• •For vehicles with petrol engine With Venturi burnerSSP 445s498_077 ThermoTop Vlies auxiliary heater• •For vehicles with diesel engine With fleece burnerSSP 493s498_07954Electrical SystemVehicle lightingXenon headlights with LED daytime running lightsIn this headlight module, the dipped beam and main beam headlights are integrated into the Xenon module (D1S, 35 W). Furthermore the headlights have LED daytime running and side lights. Fifteen individual LEDs are arranged around the Xenon module. This reduces the power consumption for the daytime running lights to approximately 30 Watts. In comparison, keeping the dipped beam headlights switched on constantly as daytime running lights requires around 140 to 180 Watts. A conventional turn signal completes the headlight module.Daytime running and side lights (15 LEDs,·30 W in total) Dipped beam and main beam (Xenon D1S, 35 W)s498_087 Turn signal (24 W)LED tail light clusterThe rear lights on the Golf Cabriolet 2012 are in two parts. They are removed and installed in the same way as the Golf 2009 rear lights.LED tail and brake light Reflector (in lens)s498_089 Turn signal (21 W) Reversing light (16 W) Rear fog light (3xLED; 3 W in total)Observe the instructions in the workshop manuals when working on the front and rear lights.55Electrical SystemVehicle electrical systemThe following diagram shows how the control units in the Golf Cabriolet 2012 are networked. It uses the network of a fully equipped vehicle with all options as an example.J503 J604 J738 R R78 R215E313 J104 J217 J234 J250 J500 J623 J667 J745 J668 J533 J791 J844 G85T16CX1 J367J255/J301 J256 G397 J400 G273/G384 H12 J345 J519 J772 J386 J387 J527 J388 J389 J453 s498_080J28556KeyCX1 E313 G85 G273 G384 G397 H12 J104 J217 J234 J250 J255 J256 J285 J301 J345 J367 J386 J387 J388 J389 J400 J453 J500 Alternator Selector lever Steering angle sender Interior monitoring sensor Vehicle inclination sender Rain and light sensor Alarm horn ABS control unit Automatic gearbox control unit Airbag control unit Electronically controlled damping control unit Climatronic control unit Convertible roof actuation control unit Control unit in dash panel insert Air conditioning system control unit Trailer detector control unit Battery monitor control unit Driver door control unit Front passenger door control unit Rear left door control unit Rear right door control unit Wiper motor control unit Multifunction steering wheel control unit Power steering control unit Powertrain CAN data bus Convenience CAN data bus Infotainment CAN data bus LIN data bus CAN data bus line LIN data bus line K-wire J503 J519 J527 J533 J604 J623 J667 J668 J738 J745 J772 J791 J844 R R78 R215 T16 Control unit with display for radio and navigation Onboard supply control unit Steering column electronics control unit Data bus diagnostic interface Auxiliary air heater control unit Engine control unit Output module for left headlight Output module for right headlight Telephone controls control unit Control unit for cornering light and headlight range control Reversing camera system control unit Park assist steering control unit Main beam assist control unit Radio TV tuner Interface for external multimedia unit 16-pin connector 57Convenience ElectronicsMain beam assist (MBA)Main beam assist enables the main beam to be switched on and off automatically depending on the traffic situation.DesignThe “eye” of the system is a black and white camera that is integrated into the mirror base. The control unit electronics of the main beam assist control unit are located in the interior mirror housing. The control unit is connected to the data bus diagnostic interface via the powertrain CAN data bus. Main beam assist control unit J844 in interior mirror housingCamera in mirror base s498_094NetworkingJ533G44 J104 J844 G45 G46 G47G213 E1J519 E650K1 J285 Y25s498_092KeyE1 E650 G44 G45 G46 G47 G213 J104 J285 J519 Light switch Button for main beams Rear right speed sensor Front right speed sensor Rear left speed sensor Front left speed sensor Rain sensor ABS control unit Control unit in dash panel insert Onboard supply control unit J533 J844 K1 Y25 Data bus diagnostic interface Main beam assist control unit Main beam warning lamp Segment display in dash panel insert Sensor/input Actuator/output58How it worksThe mai