TECHNICAL DOCUMENTATION

SSP 506 The Crafter 4MOTION with Achleitner four-wheel drive

PDFEN68 pages6 MB
SSP 506 The Crafter 4MOTION with Achleitner four-wheel drive - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingCommercial VehiclesSelf-study programme 506The Crafter 4MOTION with Achleitner four-wheel drive S506_002No race is tougher, none demands more from racers and their machines – The Rallye Dakar is a legendary event and, in January 2012, provided the perfect stage for the first major appearance by the new Crafter 4MOTION with Achleitner four-wheel drive. The Crafter 4MOTION, alongside the Amarok, completed the Rallye Dakar stage-by-stage with masterful aplomb as an official support vehicle, bringing the race management and service teams reliably to their destinations. Thanks to its permanent heavy-duty four-wheel drive system from Achleitner, the Crafter 4MOTION succeeded in covering the almost 9000 kilometres through Argentina, Chile and Peru with mountain pass climbs in excess of 4500 metres, through burning hot desert sand and muddy fords. The Crafter 4MOTION represents Volkswagen Commercial Vehicles' entry into the four-wheel drive segment in 3.5 t and 5 t gross vehicle weight rating. Now, the company offers a second four-wheel drive vehicle in the heavyduty segment alongside the Amarok. Heavy-duty four-wheel drive vehicles are designed for use under tough off-road conditions in order to meet the most demanding all-terrain requirements which would exceed the capabilities of an on-road four-wheel drive system. By cooperating with the Austrian four-wheel drive specialist, Achleitner, Volkswagen Commercial Vehicles is now able to offer a complete four-wheel drive range across its entire model portfolio.The self-study programme presents the design and function of new developments! The content will not be updated.Current testing, setting and repair instructions can be found in the provided service literature.Important note2 At a glanceCrafter 4MOTION with Achleitner four-wheel drive . . . . . . . . . . . . . . . . . . . . . 4Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Running gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18Transfer box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30Front final drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41Rear axle and final drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45Four-wheel drive control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64Check your knowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .663 Crafter 4MOTION with Achleitner four-wheel driveFour-wheel drive from the LT1 to the CrafterLT1 The LT1 was offered by Volkswagen Commercial Vehicles as an ex-works four-wheel drive vehicle from 1987 to 1996.S506_071Crafter 4MOTION From 2012 onwards, the Crafter 4MOTION will be produced as a cooperation with Achleitner Fahrzeugbau.S506_0724 Cooperative partnershipCommercial vehiclesS506_005The Crafter 4MOTION represents the onset of an innovative form of cooperation between Volkswagen Commercial Vehicles and a body builder. Achleitner Fahrzeugbau is a body builder company with experience in four-wheel drive applications. It has fundamentally pursued the development of its own four-wheel drive system and adapted it for the Crafter in line with the requirements of Volkswagen Commercial Vehicles. The Crafter 4MOTION is marketed as a two-invoice vehicle sold via Volkswagen Commercial Vehicles. Despite the vehicles being produced by two manufacturers, all the service and support work is undertaken solely by Volkswagen Commercial Vehicles and its service partners. This concept offers a range of advantages for service and the end-user: • • • • • • • Ensuring Volkswagen quality standards also for Achleitner four-wheel drive products The same warranty conditions for Volkswagen Commercial Vehicles and Achleitner products Convenient servicing because of the large worldwide dealer network Service and repair work is performed on the entire vehicle by Volkswagen Commercial Vehicles service partners Spare parts provision, service literature, technical support and warranty handling via Volkswagen Commercial Vehicles Extensive range of accessories via Achleitner Additional conversions and expansions possible from a single source via AchleitnerS506_1175 Crafter 4MOTION with Achleitner four-wheel driveVehicle productionS506_007Crafters intended for four-wheel drive are produced with the corresponding PR number 1X9 (preparation for fourwheel drive) at the production sites in Berlin and Düsseldorf, and then transported to Achleitner in Wörgl. The preparation for four-wheel drive includes the rough-road version with a raised fuel tank vent and reinforcements on the body, as well as additional preparatory options. Following conversion to four-wheel drive, the vehicles are delivered directly to dealers/importers worldwide.Production site – Achleitner FahrzeugbauS506_0086 Range of applications and usesThe Crafter 4MOTION is intended for a broad range of applications and uses such as: • • • Businesses (builders, road construction, transporting passengers, power utilities, agriculture) Public authorities and associations (local authorities, rescue services, police, aid organisations, forestry, military) Outdoor – for expeditions and tourism companies as well as for the leisure sector (camper van conversion)All standard Crafter bodies are available in all wheelbases and roof heights for conversion to four-wheel drive variants in this application range: • • Closed bodies (panel van and window van) Open bodies (platform van, double cab and chassis)This means complete special versions of the vehicle can also be produced as the four-wheel drive Crafter, e.g. ...... for the fire brigade and as an ambulanceS506_095_1... for the building trade and for local authoritiesS506_095_2... for the leisure sectorS506_095_37 Crafter 4MOTION with Achleitner four-wheel driveOverview of the complete vehicleThe Crafter 4MOTION is available with 3.5 t and 5.0 t gross vehicle weight rating and exclusively with the 120 kW engine.Multifunction steering wheel, standard outside temperature display, standard Additional roof grab handles Adapted underbody impact guard with 5 tHill hold assist StandardS506_096 Daytime running lights with 3.5 t Underbody impact guard Wing-mounted turn signalsRaised fuel tank vent Raised body Different all-terrain tyres, optionalPermanent four-wheel driveLettering on the left and right wings and on the rear of the vehicleInstalling the four-wheel drive does not require any additional adaptations to the body. Axles, shock absorbers and the suspension are connected at the mounting points familiar from the Crafter 4x2.8 The complete brake system has been taken over from the Crafter 4x2, the brake lines and the handbrake cables have been adapted for four-wheel drive. The breathers of the final drive and the transfer box are routed through a central breather hose to the bulkhead in the engine compartment. A new type approval was required for registration of the Crafter 4MOTION due to the extensive changes in comparison to the Crafter 4x2. The new test criteria in the type approval mean that vehicles with a gross vehicle weight rating of 3.5 t are equipped with daytime running lights as standard; vehicles with a gross vehicle weight rating of 5 t have an adapted side underbody impact guard.Underbody impact guardAll Crafters are equipped as standard with an underbody impact guard for the engine and for the centre bearing of the propshaft to the rear axle. The underbody impact guard for the engine is made of aluminium. Additional protective measures are available as an option, e.g. for the front final drive, the fuel tank and for the complete underbody.Underbody impact guard - engineS506_0129 Crafter 4MOTION with Achleitner four-wheel driveThe powertrainThe illustration shows the mechanical components of the 4MOTION powertrain, taking the example of the 5 tonne version with medium wheelbase.Differential lock on the rear final drive (standard)Rear axleCentre bearingPropshaftsPower transmission from the manual gearbox to the transfer box is by way of a one-piece propshaft with constant velocity joints. A shortened variant is installed in vehicles with power take-off on the gearbox side. The rear axle is driven by different two-piece propshafts with universal joints which are adapted to the wheelbase. The propshaft in the short wheelbase does not require a centre bearing. A one-piece propshaft with universal joints is fitted for driving the front axle.Support for raising the vehicle height10 Tachograph The tachograph sender G75 (for the digital tachograph DTCO) is mounted on the output of the transfer box to the front final drive.Tachograph sender G75 Holding bracket The holding bracket is used for mounting and correctly positioning the transfer box in the powertrain.Sender wheelManual gearbox All Crafter 4MOTION vehicles use the 6-speed manual gearbox 0CB. The gearbox neutral position switch F365 is used for controlling the hill hold assist. Power take-offs on the gearbox side are possible as an option. F365 Double wishbone front axle with coil springsTransfer box Off-road low range and differential lock (standard)Steering box with limit stopDifferential lock on the front final drive (optional)S506_01411 Crafter 4MOTION with Achleitner four-wheel driveTechnical data and adaptations on four-wheel driveS506_052 S506_016Engines120 kW CR TDI Exhaust standard: EURO V, EEV (Enhanced Environm entally Friendly Vehicle) CKUB 3.5 t : i = 4.1 5.0 t : i = 4.3; optionally 4.8 plus 100 mm compared to Crafter 4x2 plus 50 mm compared to Crafter 4x2 identical to the Crafter 4x2 plus approx. 3.2 m compared to Crafter 4x2 280 mm 300 mm (3.5 t) 295 mm (5.0 t) 240 - 269 mm (3.5 t) 246 - 268 mm (5.0 t) plus 100 mm compared to Crafter 4x2 (due to raised body) plus 270 - 300 kg compared to Crafter 4x2 (depending on equipment)Engine code Final drive ratioVehicle height Track width - front axle Track width - rear axle Turning circle Ground clearance front axle Ground clearance transfer boxGround clearance rear axleHeight of towing bracketKerb weightFor information about the Crafter 4x2 technical data – see SSP 369.12 Performance figures (specifically off-road properties)Entry angle to gradients at rearup to 28°S506_015_1Entry angle to gradients at frontup to 28°S506_015_2Ramp angledepending on wheelbase up to 25°S506_015_3Hill-climbing ability(including maximum payload) up to 45°S506_015_4Lateral tiltup to 43°S506_015_5Fording depthup to 600 mm The angle and tilt values can vary depending on equipment, body, wheelbase, tyres and the loading condition of the vehicle.S506_015_613 OperationOperation of four-wheel driveThe off-road low range and the 3 differential locks are engaged using function switches in a control panel between the light switch and steering wheel. The status is displayed by the warning lamps K277, K45, K46 and K74 that are integrated in the function switches of the control panel. When low range is activated, this is additionally shown by a warning lamp in the dash panel insert.The 4x4 LOW range can be engaged and disengaged completely independently from the status of the differential locks. The differential locks can only be engaged and disengaged in a certain sequence of priorities. The differential lock on the transfer box must be engaged first. Following this, the differential lock on the rear axle can be engaged and only after that the differential lock on the front axle.Indicator lampS506_017KeyE121 Rear differential lock switch E694 Button 1 (switch) for off-road low range E786 Front differential lock switch F237 Differential lock switch (transfer box) K45 K46 K74 Front differential lock warning lamp Rear differential lock warning lamp Transfer box differential lock warning lamp F237 with K74 E121 with K46 E786 with K45 E694 with K277K277 Gearbox low range warning lampStatus displays of the warning lampsWarning lamp continuously lit = four-wheel drive system activated Warning lamp flashing = gearshift procedure not yet completed Continuous flashing of a warning lamp = fault in the corresponding system Continuous flashing of warning lamps K45, K46 and K277 = overheating of the compressor14 Displays on the dash panel insertABS warning lamp K47 (ABS fault or ABS deactivated) Gearbox low range warning lamp in dash panel insertS506_018Only the activated low range is additionally displayed in the dash panel insert as the four-wheel drive function. All other four-wheel drive function are exclusively displayed by the warning lamps in the function switches.ABS system statusesIn the Crafter 4MOTION, ABS control is maintained when the centre differential is locked. ABS control is deactivated when the transverse locks are engaged. The mechanical link-up between the front and rear axles as well as the additional link-up between the two rear wheels and, if applicable also the front wheels, mean that all wheels turn at the same speed and individual wheel control during braking is no longer possible. In order to avoid negative effects on the driving behaviour, ABS control is deactivated when the rear axle lock is activated. Deactivation of the ABS is indicated by the ABS warning lamp K47 in the dash panel insert. In addition, an information text appears on the display of the dash panel insert.After the transverse locks have been switched off automatically (depending on speed) or manually, ABS control is reactivated automatically without intervention by the driver.15 OperationFour-wheel drive operating conceptOff-road range 4x4 LOWThe off-road low range can be engaged and disengaged completely independently from the status of the differential locks. Conditions for on/off • • • • Terminal 15 "ON" E694 actuated Clutch depressed Can only be engaged/disengaged when the vehicle is stationary, vehicle speed v = 0 km/hE694S506_047K277 Gearbox low range warning lampTransfer box differential lock (interaxle lock)Switch-on conditions • • • Terminal 15 "ON" F237 actuated Can be engaged/disengaged at any vehicle speedS506_048 F237Switch-off conditions • • • F237 actuated or terminal 15 "OFF" 30 s Can be engaged/disengaged at any vehicle speedK74 Transfer box differential lock warning lampRear final drive differential lock (rear transverse lock)Switch-on conditions • • • • Terminal 15 "ON" E121 actuated Interaxle lock activated Can be engaged/disengaged while driving, vehicle speed v = 0 … 45 km/hK46 Rear differential lock warning lamp E121S506_049Switch-off conditions • • • • 16 E121 actuated or vehicle speed v 45 km/h or interaxle lock deactivated or terminal 15 "OFF" 30 s Front final drive differential lock (front transverse lock)Switch-on conditionsE786• • • • •Terminal 15 "ON" E786 actuated Interaxle lock activated Rear transverse lock activated Can be engaged/disengaged while driving, vehicle speed v = 0 … 45 km/hK45 Front differential lock warning lampS506_050Switch-off conditions • • • • E786 actuated or vehicle speed v 45 km/h or interaxle or rear transverse lock deactivated terminal 15 "OFF" 30 sSpeed thresholds with transverse locks engaged • • • The transverse locks can be engaged/disengaged during driving up to a vehicle speed of 45 km/h. The transverse locks are disengaged automatically if the vehicle speed exceeds 45 km/h. If it is not possible to disengage the transverse locks manually or automatically as a result of wind-up in the driveline then the vehicle speed is limited to max. 50 km/h. The speed limit is cancelled once the transverse locks have disengaged when the wind-up has been overcome.30 s follow-on operation after terminal 15 "OFF" If the engine stalls whilst driving with the differential locks engaged, the locks remain engaged for a period of 30 seconds after terminal 15 "OFF". This means restarting and moving off are possible with the locks engaged. As a result, driving comfort is increased when driving off-road.17 Running gearFront axle with final driveTo create the space to install a front final drive, Achleitner completely redesigned the front axle. The subframe, suspension, wheel suspension, anti-roll bar and gearbox cross member were adapted for this purpose.Retainer for shock absorber and coil springAssembly carrierCross member Engine mounting support Coil spring Front final driveLongitudinal member left Rear additional spring S506_021 Gearbox cross member Input shaftGearbox mountingLongitudinal member rightThe front axle is configured as a double-wishbone axle with independent wheel suspension and coil springs. The subframe is a sheet steel structure with 3 cross members. It is used for holding the engine, the front final drive, the steering and the running gear. The left and right longitudinal members are bolted onto the subframe. The gearbox carrier is used for holding the gearbox. It is equipped with a bulge for the passage of the propshaft to the front final drive.18 middle bolted connectionS506_105Link for disconnecting the bolted connectionThe subframe and the longitudinal member are rigidly bolted to the vehicle frame using 6 bolts. If the vehicle experiences a powerful frontal collision, the middle bolted connection of the subframe can disconnect so there is no link-up to the vehicle frame. This means, in case of a crash, the subframe promotes deformation of the body longitudinal member ahead of the passenger cell, thereby contributing to passive safety. The input shafts to the front axle are configured with constant velocity joints and are of equal length for even torque distribution. The raising of the vehicle's suspension by 100 mm is achieved on the front axle by means of a subframe with an adapted profile height.19 Running gearWheel suspensionSupportCoil spring with gas-filled shock absorber on the insideRear additional spring Upper transverse link S506_103Anti-roll bar Front additional spring Lower transverse link Wheel flange (Illustration corresponds to 5 t variant) Track rodDue to the redesign of the front axle and the use of rims with an adapted offset of approx. 50 mm, the track width is approx. 50 mm wider than the Crafter 4x2. The front axles of the 3.5 t and 5 t variants are basically the same, except for the wheel flange and brake. Design differences are the configuration of the shock absorption characteristics of the coil springs and the additional springs. The wheel flange and brake are each designed specifically for the 3.5 t and 5 t variants. 2 additional springs are fitted above the upper transverse link. The shock absorption characteristics of the additional springs are configured differently for the 3.5 t model compared to the 5 t model. A comfortable suspension set-up is made possible because of the softer shock absorption characteristic in the 3.5 t model compared to the 5 t model. The support is used as a structural adapter between the suspension strut mounting and the suspension turret in the body. In the Crafter 4MOTION, only the track can be adjusted.20 Wheel bearingThe design of the wheel bearing is based on the 1st generation. The stub axle has been newly developed for fourwheel drive. The wheel hub, wheel bearing and stub axle are configured as individual components and can be renewed individually. The wheel bearing play is set using the inner grooved nut. The outer grooved nut serves as a lock nut.Cone plate Upper ball jointBrake discWheel flange (5 t model) Stub axleWheel hubWheel hub cover Drive shaft with constant velocity joint and pinABS sensor ringLower ball joint S506_022Stub axle Wheel hub Input shaft Retaining ring outer grooved nut Wheel hub coverInner grooved nutS506_02421 Running gearThe steeringSteering boxTrack rod Track rod ball joint S506_109 Steering rackTrack rod jointStop limiter rightSteering lockThe detailed view shows the example of the position of the stop limiter and steering lock on the right side of the steering. The corresponding arrangement applies on the left side.Steering boxThe wheels of the front axle are driven by drive shafts with constant velocity joints. For design reasons, driven steering axles can only achieve smaller steering stop angles compared to non-driven steering axles. For this reason, the steering stop angle must be reduced by means of stop limiters in the steering box. The stop limiters comprise steel rings that are attached to the steering rack on both sides in the steering box. These steel rings reduce the sliding travel (stroke) of the steering rack between the steering lock and the stop limiter by 12 mm in both directions. As a result, the lock angle of the wheels is reduced. The steering box is offered as a complete replacement part for the Crafter 4MOTION. The stop limiters can be renewed individually as well, however.Installing a steering box without stop limiters will result in impermissibly high flexural angles in the constant velocity joints. This can lead to breakage of the constant velocity joints in the drive shafts.22 Steering stop angleThe following steering stop angles apply to the Crafter 4MOTION: α Wheel on inside of corner = 33.4° β Wheel on outside of corner = 30.5° This produces the following turning circles: • • • 15.5 m (short wheelbase) 17.0 m (medium wheelbase) 19.4 m (long wheelbase)S506_107Steering columnThe raising of the body required modification of the steering column. This is achieved by an extended intermediate steering shaft.Intermediate steering shaftS506_10823 Running gearThe wheels and tyresVehicle Rim Tyres Remark Rolling circumference 2337 mm 2337 mm 2431 mm 2243 mm 2435 mm Snow chain capable Yes Yes No Yes No225/75 R16 Crafter 35 (3.5 t) 6.5 J x 16 H2 ET54 offset 225/75 R16 245/75 R16 205/75 R16 215/85 R16VW standard (On-road tyres) AT Achleitner option AT Achleitner option VW standard (On-road tyres) AT Achleitner optionCrafter 50 (5 t)5.5 J x 16 H2 ET109.5 offsetAT = All-terrain tyres245/75 R16 S506_113215/85 R16 S506_114 S506_115RimsAll 3.5 t versions of the Crafter 4MOTION use new rims reinforced for off-road use, with an ET54 offset.Snow chainsIt is recommended for snow chains to be used on both axles in order to improve traction and reduce wear on the centre differential.Due to the space conditions between the coil spring and tyres, it is not possible to fit snow chains on certain tyre types.24 Tyre changeIf the tyres are changed, it is necessary to adapt the dash panel insert and the electronic ignition lock if the change results in a different rolling circumference. This is the case, for example, when changing from onroad to all-terrain tyres. Vehicles with a tachograph (digital tachograph DTCO) require a special adaptation of the tachograph at an authorised service partner.S506_110 Different rolling circumferenceIf the tachograph is not adapted, the odometer display in the dash panel insert will be deleted.S506_111Wheel housing extensionThe increased track width of the front axle means the wings no longer ensure the required wheel coverage. This is compensated for by a 3-piece wheel housing extension. The wheel housing extensions are glued onto the wings and bumper.3-piece wheel housing extensionS506_12825 Running gearThe centre bearing of the propshaftVehicles with a medium and long wheelbase have a two-piece propshaft to the rear axle. This split configuration of the propshaft uses a new centre bearing which is protected against the ingress of moisture by means of deflector rings. The centre bearing is connected to the body by means of a bracket. It has an underbody impact guard made from steel sheet as standard. The flexural angle of the universal joint can be adjusted at the transfer box output to compensate for component tolerances in the bracket and to minimise vibration on the propshaft. The setting is performed using spacer plates with different material thicknesses between the centre bearing and the bracket.Transfer box BracketS506_097 Underbody impact guardBracketSpacer plates PropshaftS506_127 Centre bearingThe flexural angle must be readjusted after the bracket has been renewed. Comply with the instructions in ELSA (electronic service information system) when setting the flexural angle in service workshops.26 The exhaust systemThe exhaust system is adapted to the installation conditions of the four-wheel powertrain. The exhaust system is routed to the right side of the vehicle by means of two offset pipes. The offset pipes are integrated into the exhaust system at different positions, depending on the design (wheelbase and body). The silencer is shifted to the right by means of the front offset pipe, and is secured on the longitudinal member by means of a new mounting.Front offset pipe S506_077In vehicles with an exhaust system running as far as the end of the vehicle, there is an additional offset pipe fitted at the tailpipe.Longitudinal memberMounting for silencerS506_079In case of repair, an exhaust system for the Crafter 4x2 must be adapted to the Crafter 4MOTION. For more information, refer to ELSA (electronic service information system). S506_078 Rear offset pipe on tailpipe27 Running gearThe electronic stabilisation program ESP9iFrom 2012 onwards, all Crafters will be changed over to the electronic stabilisation program ESP9i (i = integrated) from Bosch. In this system, the ESP sensors are integrated in the ESP control unit. The previously separately installed sensor cluster is deleted. The Crafter 4MOTION uses an ESP control unit which has had its functions reduced only to ABS by the manufacturer. Only the ESP function is suppressed in this case. The ESP sensors remain active and continue to be used for implementing system functions. The ABS system of the Crafter 4MOTION has the following functions: • • • • ABS (anti-lock brake system) TCS (traction control system) MSR (engine drag torque control) Hill start assistant (as standard)S506_064 ABS control unit J104The sender wheel for registering the wheel speeds is cast in synthetic resin. This prevents the tooth gaps becoming blocked with dirt, which would lead to malfunctions in the signal recording.New wheel speed sensors adapted to the ESP9i are used (rotational speed senders G44 to G47).During installation work in the Crafter 4MOTION, make sure that the wheel speed sensors on the front axle are installed in the correct installation position! Comply with the instructions in ELSA (electronic service information system).S506_123 Right front axle drive shaftCrafter 4MOTION wheel speed sensor Sender wheel28 Hill hold assistThe hill hold assist makes it easier to move off on a slope, without the need to use the handbrake for assistance, for example. To achieve this, the hill hold assist delays the brake pressure reduction in the wheel brake cylinders when moving off. This prevents the vehicle from rolling back if there is not sufficient propulsive force to move off up the slope. The ESP sensors are used for controlling the function. The hill hold assist is activated in the Crafter 4MOTION if the following prerequisites are met: • • • • • • The engine is running (information from the engine control unit). The ABS is not deactivated. The vehicle is stationary, v = 0 km/h (information from the wheel speed sensors). The brake pedal is pressed. The uphill or downhill slope is steeper than about 3° (information from the ESP sensors in the control unit). The gear is engaged (information from the gearbox neutral switch F365).In this case, the hill hold assist always operates in the uphill moving off direction. The ESP sensors support moving off both forwards and in reverse.ABS deactivationABS can be deactivated in the Crafter 4MOTION by means of an externally available signal. When the transverse lock is engaged, this is detected by the gearbox switch for rear differential lock F100. The ABS switch-off relay J149 sends a 12 V potential to the ABS control unit J104, thus deactivating the ABS function. ABS is automatically reactivated once the transverse lock has been disengaged again.Function diagramKeyF100 Rear axle final drive differential lock switch J104 J149 J820 ABS control unit ABS switch-off relay Control unit for programmable special functionsS506_12129 Transfer boxThe transfer boxThe transfer box is mounted as an individual unit and distributes the input torque permanently to the front and rear axles. It permits operation in standard mode (4x4 HIGH) or in the off-road low range (4x4 LOW). The centre differential can be locked by means of a differential lock. The change between HIGH and LOW ranges is performed by means of a double-action pneumatic actuator cylinder.Drive from manual gearbox Output to rear final driveOutput to front final driveS506_027Technical data and features • • • • Robust structure Permanent four-wheel drive, 50:50 torque distribution Off-road low range (4x4 LOW) pneumatically shifted by countershaft Ratios: - High (HIGH): i = 1.0 - Low (4x4 LOW): i = 2.5 100 % interaxle lock in the centre differential switched by electric control motor Oil fill volume = 1.37 l Smoother running and power transmission through helical gearing Manufacturer: Aisin• • • •30 The transfer box is bolted into a holding bracket with guard plate. The holding bracket is guided in the gearbox cross member on rubber/metal mounts to reduce vibration. The low range contact switch F504 detects when the off-road low range (4x4 LOW) is activated. This is used as a status display (gearbox low range warning lamp K277) and as feedback information for the gearshift logic in the control unit for programmable special functions J820 in order to control the regeneration. If F504 fails, there is no feedback to the J820 and the gearbox low range warning lamp K277 in button 1 (switch) for off-road low range E694 flashes.Selector turning shaft Transfer box breather BellowsBellows breatherCompressed air connection Pneumatic positioning cylinder HIGH/LOW Control motor for transfer box V455 Transfer box differential lock switch F99 Output flange to front final driveGuard plate of the holding bracketContact switch for low range F504Output flange to rear final drive Breather V455 Holding bracketS506_065Pneumatic positioning cylinder HIGH/LOWDesign: Double-action pneumatic positioning cylinder without return spring Effects in case of failure: No gearshift procedure possible any longer. The transfer box remains in the range that was last engaged. The malfunction is displayed by the flashing warning lamp K277 in button 1 (switch) for off-road low range E694.31 Transfer boxGearbox section 1The 3-shaft gearbox is integrated in a 4-piece gearbox housing made from aluminium.BreatherInput shaft Input flangeIntermediate shaft HIGH / LOW double selector fork Contact switch for low range F504 Transfer box differential lock switch F99S506_054Output flange to rear final driveDifferential housingDifferential lock (interaxle lock)Output flange to front final driveThe HIGH and LOW ranges are shifted by a double selector fork. Force transmission takes place by connecting the corresponding idler gears to their shaft in a rotationally fixed connection by means of locking collars and clutch splines. Both ranges are non-synchronized. A gearbox neutral position can be selected mechanically, but is not implemented in the Crafter 4MOTION.32 Gearbox section 2Expanding wedge Tie bolt Input shaft LOW locking collar Synchro-hub on HIGH fixed gear Clutch splines LOW selector gear HIGH fixed gear Oil pump Double selector fork HIGH/LOW LOW fixed gear Clutch splines HIGH selector gear Selector fork Locking collarInput flangeS506_057Output shaft to rear final drive Oil pipe Centre differential Differential housing Synchro-hub HIGH locking collarOutput shaft to front final drive Differential lock (Interaxle lock) Lock gearing Differential housingDifferential bevel gearThe input flange is guided in the output shaft in a rotationally fixed arrangement and is in a positive-locking connection with the input shaft by means of a tie bolt. The transfer box has not only splash lubrication via the gear train but also active lubrication by an oil pump. The lubricating points are supplied from the oil pump via oil passages. The oil pipe is in a fixed installation in the output shaft to the rear axle and is mounted in a rotating arrangement in the output shaft to the front final drive. It supplies lubricating points on the output shaft to the front final drive. The centre differential configured as a bevel gear unit compensates for the speed differences between the front and rear axles. 33 Transfer boxPowerflow – HIGHS506_058Powerflow – LOWS506_05934 Interaxle differential lockTransfer box control motor V455 Helical gear ratio Pinion gear Selector rod Selector fork Output shaft (to front final drive)Locking collar Interaxle differential lock open S506_134 Locking teeth on the differential housing Differential housingThe interaxle differential lock is engaged electrically by means of the control motor for transfer box V455. The pinion gear of the control motor is connected to the spur gear ratio. The spur gear ratio carries the rotational movement into the transfer box and converts them into a thrust movement of the selector rod and selector fork.The locking collar is moved in the direction of the centre differential in order to engage the differential lock. At the same time, the locking teeth of the differential housing is connected to the longitudinal splines. The differential bevel gear connected to the output shaft to the front final drive is now in a rotationally fixed connection with the differential housing. This means the centre differential is blocked and there is no rotational speed compensation between the front and rear axles. The front axle and rear axle now always turn with the same speed.S506_125Longitudinal splinesInteraxle differential lock shifted35 Transfer boxTransfer box control motor V455The armature of the control motor forms a structural unit with the input worm. In addition, the driver and worm gear as well as the spring stop and pinion gear are firmly connected to one another. The worm drive comprising the input worm and worm gear transmits its rotational movement via the driver and the spiral spring onto the pinion gear. The spiral spring undertakes the function of an adjusting spring in this case.Pinion gear Carrier Spring stop Clamp for preloading the spring shaft Breather ConnectorTransfer box control motor V455Input wormSpiral spring (Adjusting spring) Worm gearS506_124Control of the control motor The control motor is activated by a signal output from J820, via the blocking relay J1012. The end positions and the direction of rotation of the motor are ascertained by sliding contact switches in the housing of the control motor. Effects in case of failure The differential lock remains in the currently engaged position. The malfunction is displayed by the flashing transfer box differential lock warning lamp K74 in the differential lock switch F237.Transfer box differential lock switch F99 Connector Contact viasBrush contactsS506_09436 The gearbox switch F99 has the function of a feedback switch. It detects the status of the engaged interaxle lock on the centre differential and sends this information to the control unit J820. In case of a failure, there is no longer any feedback to the control unit J820. The malfunction is displayed by the flashing transfer box differential lock warning lamp K74 in the differential lock switch F237.Function diagramS506_122KeyJ820 Control unit for programmable special functions J1012 Blocking relay 3 for transfer box V455 Control motor for transfer boxJ1010 Blocking relay 1 for transfer box J1011 Blocking relay 2 for transfer box37 Transfer boxShifting the interaxle lockEngaging During the engagement procedure, the locking teeth of the differential housing and the splines of the locking collar could end up in the tooth-on-tooth position, thus preventing the shifting procedure. In this case too, the worm drive moves through its complete turning angle, thus tensioning the adjusting spring. If there are rotational speed differences between the front and rear axles when driving on unconsolidated ground or around bends, the output shaft turns together with the locking collar. As soon as the locking teeth of the differential housing and the splines of the locking collar have turned enough for the teeth to engage, the tension force in the adjusting spring engages the lock with a time delay.Engaging in tooth-on-tooth positionSpring stop Pinion gearWorm gearSpiral spring (Adjusting spring) Transfer box control motor V455CarrierClamp for preloading the spring shaftInput wormS506_144Before engagementTooth - locking collarTooth - locking teeth (differential housing) Engagement startsS506_146 Engagement has taken place38 Disengaging During the disengagement procedure too, the worm drive always moves through its complete turning angle. As a result of the driving situation, it is possible for "wind-up" to occur in the powertrain, thus generating additional torques. This "wind-up" cannot be dissipated when driving on ground that does not permit wheel slip. The "windup" leads to increased static friction between the splines of the locking collar and the locking teeth of the differential housing. Static friction means that the locking collar remains in its position. The adjusting spring is preloaded again. The "wind-up" can be dissipated again when driving straight ahead, and this effect can be assisted by additionally applied load changes or a change in the driving direction. Once the "wind-up" has been dissipated, the locking collar is moved back into its rest position by the return force of the adjusting spring, thus disengaging the lock.Disengaging with "wind-up"S506_145Engaged with "wind-up"Dissipating the "wind-up"S506_147 Spline meshing is disengaged39 Transfer boxOil supplyThe transfer box is lubricated by pressurised recirculation lubrication during driving.Bypass valveOil pump (Rotor pump)S506_066CarrierIntermediate shaftOutput shaft to rear final driveThe pressure build-up is performed by a rotor pump. The inner ring of the rotor pump is driven by a follower on the intermediate shaft. The oil is drawn in via the intake connecting pipe with integrated oil filter. The oil passes via the pressure side through pressurised oil channels to the lubricating points. A bypass valve returns the oil from the pressure side to the suction side if a pressurised oil channel is sealed in case of a fault.Pressurised oil ductInner ring (Rotor pump)Outer raceIntake connecting pipe S506_068 Intake port40 Front-wheel driveFront-wheel driveThe Crafter 4MOTION uses a newly developed front final drive from Achleitner for its front-wheel drive. The final drives for 3.5 t and 5 t have an identical design but different ratios.Breather3.5 t : i = 4.1 5.0 t : i = 4.3 4.8 optionalDrive Right front wheel Housing cover Oil filler plugThe crown wheel diameter is 200 mm in all configurations.Differential lock actuator S506_038 Final drive input flangeAxle tube Drive Left front wheelThe final drive housing, housing cover and axle tube are made from spheroidal graphite cast iron. The solid housing cover is integrated into the final drive power transmission structure in order to increase stability. The axle tube is bolted onto the final drive housing and the stub shafts are solid. Ventilation is by way of the central ventilation line to the engine compartment.Type plateThe type plate of the front final drive is located on the front axle subframe at the front right.S506_13041 Front-wheel driveStructure of the front final driveThe front final drive consists of a bevel gear/crown wheel gearset with hypoid gearing. The differential effect is provided by a bevel gearbox fitted in the differential housing. The position of the input bevel gear in relation to the crown wheel is set using a shim in front of the inner bearing of the input bevel gear. The bearing preload is set using a ram sleeve. The backlash between the input bevel gear and crown wheel is adjusted using two shims on the differential housing. To compensate for the asymmetrical installation position of the front final drive, the left stub shaft has been extended accordingly. This means the support torques resulting from the input torques are symmetrically carried by the front axle. Negative effects on the driving properties are thus eliminated.Left stub shaft Drive Left front wheelDifferential housingLocking tubeShift dogCrown wheelDrive Right front wheelSliding piece Sliding pieceShimAxle tube Shim Bevel drive gear Shim Ram sleeve Input flange S506_051Differential lock actuatorF10142 Function of the differential lockThe differential lock is actuated by means of a double-action pneumatic actuator cylinder. The piston of the actuator cylinder is always kept in the particular selected switching position with pneumatic pressure. The follower transmits the movement of the piston to the shift dog. The shift dog can be moved on the left stub shaft in the longitudinal direction by means of splines, and is guided to prevent rotation. The return spring in the actuator is used for resetting and holding the shift dog in the rest position if there is pressure loss in the pneumatic system. The front axle final drive differential lock switch F101 has the function of a feedback switch. It detects the status of the engaged differential lock and sends this information to the J820. It is also used for displaying the status on the front differential lock switch E786 and as an input signal for controlling regeneration of the air dryer. If the switch malfunctions, there is no longer any feedback and the front differential lock warning lamp K45 flashes.Shift dog SplinesS506_116 Compressed air connection Piston rod Compressed air connectionPistonReturn springCarrierF10143 Front-wheel driveDifferential lock not actuated The spur gearing of the shift dog and of the differential housing do not mesh together, meaning that the differential housing can turn freely on the stub shaft.Left stub shaft Carrier Shift dog spur gearingSplines Differential housing spur gearingDifferential lock actuatorS506_092Differential lock actuated The differential lock actuator has pushed the shift dog over the splines on the stub shaft with its follower, in the direction of the differential housing. The spur gearing of the shift dog and the corresponding gearing on the differential housing mesh together. This means a positive connection has been established between the differential housing, shift dog and stub shaft, and the differential function is blocked. Both input gears now transmit the same rotation speeds and torques.S506_09844 Rear axle and final driveRear-wheel driveA newly developed rear axle by Achleitner is used in the Crafter 4MOTION. Similarly to the situation with the Crafter 4x2, there is a lighter 3.5 t variant and a heavier 5.0 t variant. Both variants use the same brakes and wheel bearings that are in the Crafter 4x2. The increased suspension height of the vehicle by 100 mm is achieved at the rear axle by a support between the axle tube and leaf spring. The U bolts, anti-roll bar, handbrake cables and hydraulic brake lines have been adapted accordingly. Ventilation is by way of the central ventilation line to the engine compartment.The illustration shows the 3.5 t variantFinal drive Breather Positioning element Differential lockSupport for raising the vehicle heightU bolt-Final drive ratiosS506_0293.5 t : i = 4.1 5.0 t : i = 4.3 4.8 optional Differential lock as standard 45 Rear axle and final driveStructure of the rear final driveThe final drive housing and housing cover are made from spheroidal graphite cast iron. The solid housing cover is integrated into the final drive power transmission structure in order to increase stability. Both axle tubes are pressed into the final drive housing and are welded onto the gearbox housing. The stub shafts are solid shafts in both variants.The illustration shows the 3.5 t variantLeft stub shaft Locking tube Shift dogSliding pieceAxle tube F100 ShimPositioning element Differential lockThe gearbox switch for differential lock F100 has the function of a feedback switch. It detects the status of the engaged differential lock and sends this information to the J820. It is used for displaying the status on the rear differential lock switch E121 and as an input parameter for controlling regeneration of the air dryer. If the switch malfunctions, there is no longer any feedback and the rear differential lock warning lamp K46 flashes.46 The bevel gear and crown wheel are smooth-running hypoid gearing. The crown wheel diameter is 225 mm in all configurations. The position of the input bevel gear in relation to the crown wheel is set using a shim behind the inner bearing of the input bevel gear. The bearing preload for the input bevel gear is set using a ram sleeve. The backlash between the bevel gear and crown wheel is adjusted using two shims on the differential housing. The design structure and function of the differential lock correspond to the configuration in the front final drive.Input flange Ram sleeveShim Bevel drive gear Crown wheelS506_03947 Four-wheel drive controlControl of four-wheel driveThe two overviews show the main components of the four-wheel drive control in the Crafter 4MOTION. To assist understanding, the four-wheel drive control is shown in two graphics, which build on one another. The view of the vehicle with the four-wheel drive system clearly shows the spatial arrangement of the four-wheel drive components - in the view without the body, the individual components relevant to fourwheel drive can be seen, as can their allocation within the system.Positioning element Transverse lock rearBreather line for rear final driveOverview – Crafter 4MOTION with four-wheel drive systemElectric line for rear transverse lockControl lines (pneumatic, electric) and breather lines Seat box on driver's side Four-wheel drive control Function switch for four-wheel drive controlControl unit for ABS J104Four-wheel drive powertrain S506_01148 Seat box on driver's side Four-wheel drive control pneumatic linesFunction switch for four-wheel drive control Compressed air to valve block in seat boxelectric lines Regeneration line to compressorControl motor for transfer boxGearbox breather into the engine compartmentpneumatic positioning cylinder HIGH/LOW Air compressor with pressure accumulator S506_073 Air intake air compressorFront transverse lock actuator49 Four-wheel drive controlThe driver seat box – installation locationsThe main components of the pneumatic and electrical controller of the four-wheel drive are installed in the driver seat box. The fuses relevant for four-wheel drive are located in the fuse holder SD and on the fuse and relay carriers of the driver seat box.Driver's seat box Fuse and relay carriers S131 J1013 J1009J1014J1008 J149 J820 Solenoid valve blockS187 J1012 J1011 J1010S133 S134 S132S506_089 Fuse carrier SDKeyJ149 J820 ABS switch-off relay Control unit for programmable Special functions J1013 Control unit for pneumatic compressor protection J1014 Relay for pneumatic compressor S131 S132 S133 S134 S187 Fuse 1 Fuse 2 Fuse 3 Fuse 4 Differential lock fuseJ1008 Relay for pneumatic compressor regeneration J1009 Relay for pneumatic compressor enable J1010 Blocking relay 1 for transfer box J1011 Blocking relay 2 for transfer box J1012 Blocking relay 3 for transfer box50 Air compressor protection control unit J1013The control unit performs the following tasks: • • • Controlling the switch-on logic of the compressor Regeneration of the air dryer Overheating monitoring and deactivationJ1013Diagnosis is exclusively via checks based on the current flow diagram.Function diagramS506_131Regeneration valveTemperature monitoringRegeneration activationTemperature monitoringS506_132KeyF100 Rear axle final drive differential lock switch F101 Front axle final drive differential lock switch F503 Pressure switch for pneumatic compressor F504 Contact switch for low range J820 Control unit for programmable Special functions J1009 Relay for pneumatic compressor enable J1013 Control unit for pneumatic compressor protection J1014 Relay for pneumatic compressor N570 Solenoid valve for rear axle differential N571 Solenoid valve for front axle differential N572 Solenoid valve for low rangeJ1008 Relay for pneumatic compressor regeneration51 Four-wheel drive controlThe compressed air carrier unitAir filter Interior Pressure switch Pneumatic compressor V534 Intake hose to air filterBleeder valvePressure accumulatorS506_040The compressed air carrier unit consists of an electrically operated pneumatic compressor and a separate pressure accumulator. The stainless steel pressure accumulator has a capacity of 2 l. The components are mounted in a support with a vibration-dampened mounting unit in the engine compartment between the air intake box and the engine. The air is drawn via a hose from the air filter box. The intake connection is located behind the air filter for the interior ventilation. System pressure: 8 to 10 barSwitch-on conditions of pneumatic compressor: Engine running System pressure 8 bar Regeneration mode not activeOnce the pressure has built up in the compressor, the system pressure is present permanently up to the compressed air actuator cylinders. For reasons of safety, the system pressure must be dissipated via the bleeder valve before repair work is performed on the pneumatic system.52 The pneumatic compressor V534 with connectionsRegeneration valve Pressure connection Intake line Air dryer Compressor Regeneration line from solenoid valve block Dummy plugT-electrical connector with test connectionPressure line to solenoid valve block Pressure line to pressure accumulator Non-return valve 1 Pressure accumulator Pressure switch for pneumatic compressor F503S506_081Sender for compressor temperatureBleeder valvePressure switch for pneumatic compressor F503The pressure switch for pneumatic compressor F503 is bolted onto the pressure accumulator and is a pressuredependent switch for switching the pneumatic compressor on and off. The switch is closed when depressurised. After the engine has started and at a pressure of 8 bar, the F503 switches the pneumatic compressor on and the system pressure rises. At 10 bar, the switch opens and the compressor is switched off. The switching hysteresis of 2 bar means the compressor is switched back on again when the system pressure drops to 8 bar.Effects in case of failureThe compressor cannot run if there is an electrical discontinuity or if the mechanism of the pressure switch is blocked in the open condition. When F503 is blocked in the closed condition, the compressor continues to run in continuous operation. If the system pressure is 15 bar or more, the pressure limiting valve in the compressor opens in order to protect the component, or the compressor is switched off by the overheating shut-off when the maximum temperature is reached.53 Four-wheel drive controlPneumatic compressor V534BodyNon-return valve Connector Regeneration valve Regeneration valve Air dryer Sender for compressor temperaturePressure connectionDiaphragm valve "closed" Piston ringConnection to air filterReciprocating pistonIntake connectingBypass valveS506_043 Electric motorThe compressed air is created by a single-stage reciprocating piston compressor with an integrated air dryer. In order to avoid contamination of the U-bellows and the air dryer (dryer cartridge), the compressor is configured as a dry-running compressor. Continuously lubricated bearings and a piston ring made from PTFE (polytetrafluoroethylene) ensure long durability. The housing of the air dryer integrates the regeneration valve, bypass valve, pressure limiting valve and a nonreturn valve.54 FunctionSuction/compression When the piston moves upwards, air is drawn out of the air filter box through a hose and then through the intake connecting pipe into the crankcase. Above the piston, the air is compressed in the cylinder and channelled through the non-return valve into the air dryer. After passing the air dryer, the compressed and dried air enters the pressure accumulator.Non-return valve "opened" Air dryer Diaphragm valve "closed"Piston moves upwards Pressure connection Intake connecting pipe Connection to air filterCrankcaseS506_140Overflow During the downwards movement of the piston, the air drawn into the crankcase passes through the diaphragm valve into the cylinder.Non-return valve "closed" Cylinders Diaphragm valve "open"Overflowing airPiston moves downwardsS506_14155 Four-wheel drive controlPneumatic circuit of the pneumatic compressors V534CompressorS506_082KeyE Connection to air filterA Pressure connection D Pressure accumulator 1 Interior air filter 2 Electric motor 3 Compressor 4 Non-return valve 5 Air dryer 6 Pressure limiting valve (safety switch) 7 Bypass valve 8 Regeneration valve 9 Sender for compressor temperatureAll valves are in rest position during filling of the compressed air system. The air is directed from the compressor via the air dryer to the pressure accumulator. Compressor operating pressure: 13.2 bar Pressure limiting valve opening pressure: approx. 15 barDrawn-in/compressed air56 Overheating protectionE121E786E694K46K45K277Sender for compressor temperatureS506_086The piston which runs dry in the cylinder of the compressor generates relatively high heat losses during operation. The short operating cycles of the compressor means there is no critical temperature rise in normal operation. To protect the compressor against overheating, it has a temperature monitoring function with overheating shut-off. The temperature is measured using the sender for compressor temperature inserted in the cylinder head. The control unit for pneumatic compressor protection J1013 calculates the current compressor temperature by means of the temperature-dependent NTC resistor and a characteristic map. The compressor is switched off as soon as it reaches a critical temperature. Switch-off temperature: 100 °C Switch-on temperature after cooling-down phase: 80 °C The overheating switch-off is displayed by warning lamps K45, K46 and K277 flashing together. Following three overheating shut-offs, the compressor is switched off permanently for this tl. 15 cycle. The shut off is reset after the ignition is switched off and on.57 Four-wheel drive controlRegenerationAir dryer with granulate fillCompressorS506_083KeyE Connection to air filter 4 Non-return valve 5 Air dryer 6 Pressure limiting valve (safety switch) 7 Bypass valve 8 Regeneration valve 9 Sender for compressor temperatureA Pressure connection D Pressure accumulator 1 Interior air filter 2 Electric motor 3 CompressorReturned air (regeneration)The air in the compressed air system must be clean and dry. Moisture would increase the susceptibility to corrosion and could lead to freezing. A zero-maintenance air dryer with granulate fill is used to dehumidify the air. This granulate can absorb more than 20% of its own weight in humidity, depending on the temperature. Pressure build-up – During the pressure build-up, the air passes through the dryer after compression, which removes the moisture from it. Depressurisation – During all pneumatic switching procedures, the air is returned from the pressure-reducing chambers of the double-action air cylinders to the compressor. In this case, the air flows through the granulate fill of the air dryer in the opposite direction, and reabsorbs the temporarily stored moisture. The moisture-enriched air is returned as far as the air filter box. In order to perform the regeneration, the regeneration valve is activated via the control unit for pneumatic compressor protection J1013. The regeneration valve is now open, thus pneumatically activating and opening the bypass valve. When the bypass is open, the mechanical part of the compressor is bypassed and the air can flow back into the air filter box without resistance.58 During regeneration, the compressor is activated by the control unit for pneumatic compressor protection so that it does not build up any pressure. This avoids malfunctions in the pneumatic system. The regenerative process means the air dryer does not require maintenance.Function diagramStatus request Four-wheel drive functionsStatus request Gearbox switchRegeneration valveS506_085The regeneration process always takes place in each pneumatic switching procedure. The control unit for pneumatic compressor protection J1013 permanently checks the status of function switches E694, E786 or E121. Actuating a function switch opens the regeneration valve and initiates the regeneration. Following the pneumatic switching procedure, the status of the pneumatic positioning cylinder is transferred via gearbox switches F100, F101 and F504 to the control unit for pneumatic compressor protection J1013 and regeneration is terminated with a run-on time of 5 s.59 Four-wheel drive controlSolenoid valve blockThe solenoid valve block is used for pneumatic control of the double-action pneumatic positioning cylinders and for venting via the regeneration connections. The solenoid valve block consists of three 5/2-way valves with an identical structure. Electrical activation is directly via the control unit for programmable special functions J820. For checking the function in service, it is possible to control the valve by manual actuation.Pressure output to the positioning cylinderManual confirmationPressure output to the positioning cylinder Connector N570 Carrier plate Connector N572 Connector N571S506_088N570 N572 N571 Regeneration to the compressor Pressure input from the pressure accumulator Regeneration to the compressorKeyN570 N571 N572 Solenoid valve for rear axle differential Solenoid valve for front axle differential Solenoid valve for low rangeFor identification during service, the pneumatic lines are fitted in different colours (blue or black). All the regeneration lines are green.60 Pneumatic circuitRear axle lock4x4 LOWFront axle lock Position cylinderSolenoid valve blockRSV2RSV1S506_080KeyD F503 N570 N571 N572 Pressure accumulator Pressure switch for pneumatic compressor Solenoid valve for rear axle differential Solenoid valve for front axle differential Solenoid valve for low range RSV2 V534 P RSV1 Test connection (behind the compressor) Non-return valve 1 (installation location behind the compressor) Non-return valve 2 (installation location in the driver's seat box) Pneumatic compressor61 Four-wheel drive controlSystem overviewKeyE121 Rear differential lock switch E694 Button 1 (switch) for off-road low range E786 Front differential lock switch F99 Gearbox switch for differential lock of the transfer boxF100 Gearbox switch for differential lock of the rear final drive F101 Gearbox switch for differential lock of the front final drive F237 Differential lock switch (transfer box) F504 Contact switch for low range J820 Control unit for programmable special functions J1013 Control unit for pneumatic compressor protection N570 Solenoid valve for rear axle differential N571 Solenoid valve for front axle differential N572 Solenoid valve for low range V455 Control motor for transfer box V534 Pneumatic compressor Comfort CAN - Engine speed - Speed - Clutch pedalJ820S506_07462 The control unit for programmable special functions J820 is the central building block of the four-wheel drive system. The parameter settings of the J820 control and monitor the switching logic of the differential locks and the 4x4 LOW range. The parameter settings are the same for both variants (with/without front differential lock). In addition for four-wheel drive parameter settings, the J820 can be given additional parameter settings such as control of the power take-off or the working speed control. The four-wheel drive parameter settings are stored in the Guided Fault Finding of the Volkswagen diagnostic tester.Additional free parameter settings made in service can damage the four-wheel drive parameter settings. This will lead to malfunctions of the four-wheel driveRelay carrier driver's seat box63 ServiceSpecial toolsDesignation Hook spanner T50034 Tool Use Assembly work on the wheel bearing of the front axleS506_138Tester for pneumatic control VAS 6810Diagnostic work on the pneumatic control, e.g. leakage test, switchoff or switch-on pressure, pressure lossS506_139Special maintenance specifications apply to four-wheel drive, e.g. special oil change intervals – see ELSA (electronic service information system).64 Information about towingIt may be necessary to comply with country-specific statutory provisions when towing.In case of transfer box damageThe propshafts to the driven axles must be removed or disconnected.In case of front axle damageTow with the front axle raised. The propshaft between the rear axle and transfer box must be removed or disconnected.In case of rear axle damageTow with the rear axle raised. The propshaft between the front axle and transfer box must be removed or disconnected. If the propshaft is not disconnected when towing with an axle raised and the wheels stationary then theS506_137centre differential will be operated with impermissible high revs. In addition, lubrication of the transfer box is reduced because the oil pump is not driven in this case. This will lead to massive transfer box damage. If a vehicle without gearbox damage is towed on both axles then the transfer box will be driven by the axles. The turning intermediate shaft drives the oil pump and lubrication is maintained in the transfer box.65 Test your knowledgeWhich answer is correct?One or more of the model answers could be correct. 1. Under what conditions can the 4x4 LOW off-road range be engaged? The following engagement conditions must be necessary. a) Ignition (tl. 15) switched on, driving speed v = 0 km/h, clutch actuated. b) Engine running (n 1000 rpm), driving speed v = 0 km/h, clutch actuated. a) Tl. 15, driving speed v 45 km/h, clutch actuated.❒ ❒ ❒2.What needs to be taken into account when operating the four-wheel drive components? a) The actuation sequence can be selected by the driver as required. b) The differential locks can only be engaged in the following priority sequence: 1st interaxle lock in transfer box, 2nd transverse lock on rear axle 3rd transverse lock on front axle. c) The differential locks can only be engaged when 4x4 LOW range is engaged and in the following priority sequence: 1st interaxle lock in transfer box, 2nd transverse lock on rear axle 3rd transverse lock on front axle.❒ ❒ ❒3.Why are steering lock limiters fitted in the steering box in the Crafter 4MOTION? a) To prevent the all-terrain tyres brushing against the wheel housing at full lock. b) The turning circle must be increased for safety reasons, in order to reduce the risk of tipping over when cornering. c) For design reasons, the constant velocity joints of the drive shafts of the front final drive only permit limited flexural angles.❒ ❒ ❒4.What needs to be taken into account when changing to a modified wheel rolling circumference (e.g. when changing from on-road to all-terrain tyres)? a) No changeover is permitted. b) The instrument cluster, electronic ignition lock and tachograph must be adapted to the modified rolling circumference. c) The control unit J820 must be provided with an adapted coding.❒ ❒ ❒66 5.Which statement about the function of the adjusting spring in the servomotor for transfer box V455 is correct? a) The adjusting spring in the gearshift mechanism of the servomotor V455 is always preloaded in each shift procedure. b) The adjusting spring creates a synchromesh effect during the gearshift, so that the lock can also be engaged when driving. c) The adjusting spring preloads the gearshift mechanism in the servomotor V455 if, during the gearshift procedure, the gearing of the locking collar and the locking teeth of the differential housing match up when facing one another.❒ ❒ ❒6.Where is the front final drive type plate located? a) The type plate is located on the front axle subframe. b) the type plate is located on the housing of the front final drive. c) The type plate is located on the driver seat box.❒ ❒ ❒7.By means of which control unit is the regeneration valve in the air compressor controlled? a) By means of the compressor control unit J104 installed inside the compressor. b) By means of control unit J820. c) By means of the air compressor protection control unit J1013.❒ ❒ ❒8.When are the double-action pneumatic actuator cylinders for the transverse locks and 4x4 LOW pressurised with compressed air? a) The system pressure is only present up to the actuator cylinders when the engine is running. b) Once the pressure has built up in the compressor, the system pressure is present permanently up to the compressed air actuator cylinders. c) The system pressure is only present up to the actuator cylinders during the gearshift procedure.Solution: 1. a); 2. b); 3. c); 4. b); 5. c); 6. a); 7. c