TECHNICAL DOCUMENTATION
SSP 508 The 10l 44 55 kW MPI Engine

This PDF is currently unavailable.
Read document text
Service TrainingSelf-study programme 508 The 1.0 l 44/55 kW MPI Engine Design and functionThe 1.0 l 44/55 kW MPI engine, featuring the same intake manifold injection as in the up!, is the first example of a completely newly developed generation of engines which are now being installed in diverse models across the Volkswagen Group. For the market launch of the up! there are two power versions, one with 44 kW and one with 55 kW. At a later point in time there will also be an up! EcoFuel with 50 kW. When an engine is newly developed, or improved, there are always a multitude of specifications which must be met. Along with fuel consumption and therefore the CO2 emissions, weight, costs and compliance with existing and future exhaust emission standards, attention must also be paid to the most compact design possible. The new series of engines have allowed all these targets to be achieved. As the new generation of engines presently stands, there are the following capacity and power versions available: 1.0 l 44 kW to 55 kW 1.2 l 63 kW to 77 kW 1.4 l 66 kW to 110 kW 1.6 l- 77 kW to 88 kW with intake manifold injection with direct injection with intake manifold injection or direct injection with intake manifold injections508_777On the following pages, we will be introducing you to the design and function of the new 1.0 l 44/55 kW MPI engine with intake manifold injection.The self-study programme presents the design and function of new developments! The content will not be updated.Current testing, setting and repair instructions can be found in the provided service literature.Important note2ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Technical features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Engine Mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Poly V-belt drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Toothed belt drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Cylinder block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Crankshaft drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Cylinder head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Camshaft housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Valve gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Oil supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Crankcase breather and ventilation system . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Intake system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Engine Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . System overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Actuators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 24 26 27 31Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Special tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Test Your Knowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 343IntroductionThe 1.0 l 44/55 kW MPI EngineThe 1.0 l 44/55 kW MPI engine is a completely new design, and is the first in a new generation of engines. The engine mechanics are the same for both power variants. The differences in power are achieved by the software. Technical features • • • • • • Camshafts driven by a toothed belt Camshaft housing features a modular design Cylinder head with integrated exhaust manifold Coolant pump integrated into the thermostat housing Coolant pump driven by a toothed belt from the exhaust camshaft Inlet camshaft adjustments508_089Technical dataEngine code Design Displacement Bore Stroke Valves per cylinder Compression ratio Max. output Max. torque Engine Management Fuel 44 kW at 5500 rpm CHYA CHYBTorque and performance diagram[Nm] 110 100 90 80 70 60 50 1000 3000 5000 [kW] 60 50 40 30 20 10 0 7000 [rpm]3-cylinder inline engine 999 cm3 74.5 mm 76.4 mm 4 10.5:1 55 kW at 6200 rpm95 Nm at 3000-4300 rpm Bosch Motronic ME 17.5.20 Super unleaded RON 95 (normal unleaded RON 91 with a slight reduction in performance) Three-way catalytic converter with one step-type lambda probe upstream and one downstream of the catalytic converter EU5s508_090 44 kW: 55 kW:Exhaust gas treatmentEmissions standard4Engine MechanicsPoly V-belt driveThere are two basic types of poly V-belt drive, one with and one without an air conditioner compressor. Both are driven by a six-rib poly V-belt. The belt pulley on the crankshaft is equipped with a vibration damper to ensure the engine runs quietly.Poly V-belt drive without A/C compressor:Without the air conditioner compressor, only the alternator is driven. The poly V-belt (Optibelt) is flexible and elastic. The combination of this, and low mechanical stresses, means a tensioning roller is not required. Belt pulley alternator Poly V-belt (Optibelt) s508_003 Belt pulley alternator Poly-V-belt Crankshaft pulley with vibration damper s508_005 Tensioning roller Belt pulley air conditioner compressor Crankshaft pulley with vibration damperPoly V-belt drive with A/C compressor:If an air conditioner compressor has been installed, then a standard poly V-belt is used. This version tensions the poly V-belt using a fixed tensioning roller.An automatic tensioning roller and an alternator with a coasting function are installed in all vehicles which feature BlueMotion technology, regardless of whether an air conditioner compressor has been installed. They reduce friction and fuel consumption. 5Engine MechanicsToothed belt driveThe camshafts are driven by a maintenance-free toothed belt. It is tensioned using an automatic tensioning roller, which uses contact shoulders at the same time to ensure the toothed belt is guided correctly. A idler roller on the tensioning side and tri-oval camshaft gears ensure the toothed belt runs smoothly.Tri-oval gear Exhaust camshaftTri-oval gear Inlet camshaft with vane-type adjusterPlug Tensioning roller s508_093 Idler rollerBacking materialTension cables Tooth fabric made of polyamide and Teflon Crankshaft pulleyToothed belt with a coating made of polytetrafluoroethylene (Teflon) to reduce wears508_029Toothed belt coverThe toothed belt is protected against the ingress of dust and dirt by a three-part toothed belt cover. This extends the service life of the toothed belt.Plastic cover with injectionmoulded sealAluminiumsilicon coverPlastic cover with injection-moulded seals508_0706Toothed belt drive with tri-oval camshaft gearsA certain amount of force is required to open the valves of a cylinder. This force also acts on the toothed belt drive every time the valve is opened, and at higher speeds will cause it to vibrate. To minimise the strong vibrations which are typical for 3-cylinder engines in particular, special camshaft gears have been employed. It has been designed with a larger radius, at intervals of 120° (tri-oval).How it worksInlet valve starts openingCircumference on radius r1The larger radius (r1) enlarges the moment arm acting on the valves when they start to open. This allows the force of the toothed belt to be reduced, but still allows an equally high moment to be transmitted as a standard gear does. The lower force of the toothed belt minimises annoying vibrations.r1 r2 r2r1r1Toothed belt forcer1 r2r2s508_024 Radius r1 - large 53.75 mm r2 - small 51.55 mmForce when opening starts Tri-oval gear with two Standard gear with uniform different radii radiuss508_092You will require the assembly tool VAS 10476 to position the tri-oval camshaft gear.AdvantagesThe lower toothed belt forces allow the tension force of the tensioning roller to be reduced. This results in lower friction and mechanical stress on the entire toothed belt drive. The reduced level of vibrations allows the toothed belt drive to run even more quietly.7Engine MechanicsCylinder blockThe cylinder block consists of cast aluminium and has been designed as an open-deck version. Open deck means that it has no webs between the outer wall of the cylinder block and the cylinder tubes. This has the advantage of: - No air bubbles being able to form in this area, which would lead to ventilation and cooling problems - Cylinder deformation is kept low when the cylinder head is bolted to the cylinder block. The piston rings can easily compensate for this low level of cylinder deformation, and the consumption of oil is reduced. The oil pressure supply lines, the oil return pipes and the crankcase breather have been cast into the cylinder block. This reduces the number of additional components as well as the amount of machining required.Cylinder liners Untreated greycast surfaceOil returnCylinder barrelDuct for internal crankcase breatherCylinder blockOil supply lines508_020 Crankcase breatherGrey cast iron cylinder linersThe grey cast iron cylinder liners are individually cast into the cylinder block. Their outer surface is very rough, which increases the surface area and improves the transfer of heat to the cylinder block. Furthermore, this ensures the fit between the cylinder block and the cylinder liner is a very good positive one.8Crankshaft driveThe crankshaft drive was designed for low, moving masses and low friction. The weight of the conrods and the pistons has been so well designed that the balancer shaft, otherwise standard in three-cylinder engines, could be eliminated. Together with the small main bearings and conrod bearings, which have a diameter of 42 mm, the weight of the engine, and the drive gear friction, could be reduced even further. The cast crankshaft with four bearings features six counterweights which reduce the inner forces of the crankshaft and therefore the load on the main bearings.PistonConnecting rodBearing shellsConrod bearing capCrankshaft s508_082Securing bolt T10340s508_087 Crank webConrodThe connecting rods are fracture-split. Fracturing involves machining the conrods as complete parts, and only when this is finished are they split into a connecting rod and conrod bearing cap. The advantages are: - A non-interchangeable fracture surface is produced, and only the two components made from the one blank will fit together. - Its manufacture is inexpensive - There is a good frictional lock between the componentsNote that when adjusting the valve timing, the crank web should only just be touching the securing bolt. The crankshaft is not fixed and can be rotated against the direction of engine rotation.9Engine MechanicsCylinder headThe 4-valve cylinder head is made of an aluminium alloy.Camshaft housing gasket The gasket is a metal bead gasket. It is designed with a cover plate and a special oilresistant and hydrocarbon-resistant coating.Cylinder head gasket The cylinder head gasket is a single-layer metal gasket. Due to the low combustion pressures and low cylinder block distortion, a single-layer gasket is adequate.Camshaft housing gasketRoller rocker fingersCoolant temperate sender G62Cylinder head gasket s508_032Coolant temperature sensor G62 The coolant temperature sender has been screwed into the integrated exhaust manifold, and measures the temperature of the coolant. This is where the highest temperatures are found.10Integrated exhaust manifoldThe three exhaust ports within the cylinder head have been combined into one central flange in the integrated exhaust manifold. The catalytic converter is bolted directly onto this flange.Design The cross-flow cylinder head allows the coolant to flow from the inlet side to the exhaust side via the combustion chambers. On the exhaust side, it is divided into two areas, one above and one below the exhaust manifold. It flows through several ports, absorbing the heat. It flows from the cylinder head into the thermostat housing, mixing with the remaining coolant.Lambda probe upstream of catalytic converter Upper cooling areas508_033 Lower cooling area Exhaust ports Three-way catalytic converterThis design has several benefits: The coolant is warmed up more quickly by the exhaust gas while the engine is warming up. The engine reaches its operating temperature faster. This reduces fuel consumption, and the vehicle interior can be heated more quickly. Due to the smaller area of the exhaust gas-side wall surface extending to the catalytic converter, the exhaust gas does not emit as much heat during the warm-up phase, and the catalytic converter is more quickly heated up to its operating temperature by the coolant, despite its cooling effect. When the system is operating under full load, the coolant temperature is further reduced, thereby increasing the engine operating temperature range at which lambda = 1. Fuel consumption and exhaust emissions are thus optimised.--Integrated exhaust manifolds508_03411Engine MechanicsCamshaft housingThe camshaft housing is made of cast aluminium and, together with the two camshafts, forms an integral module. This means that the four-bearing camshafts can no longer be removed. To reduce friction, the first bearing of that particular camshaft, which is subjected to the highest load from the toothed belt drive, is a grooved ball bearing. Furthermore, the camshaft housing is used to accommodate the valve for the variable valve timing N205, the Hall sender G40 and the non-return valve for the crankcase ventilation system.Non-return valve for the crankcase ventilation system Hall sensor G40 Valve for variable valve timing N205Exhaust camshaft tube Cam Grooved ball bearingPlugSeals508_019 Camshaft housingSender wheel Inlet camshaft tube Seal Snap ringThe grooved ball bearings are secured by a snap ring, however they cannot be replaced.12Modular camshaft housing designThe modular design involves assembling the camshafts directly in the camshaft housing. Assembly During assembly, the cams were initially warmed, before being positioned in the housing. At the same time, the camshaft tube is cooled intensively and inserted into the camshaft housing through the cams. Once the components reach ambient temperature, an inseparable join is created. As the cams no longer have to fit through the bearing points, it is possible to design very small bearings.Advantages of smaller bearing points: lower friction in the bearings and higher rigidity.In the event of a repair, the camshaft housing is replaced together with the camshafts.Grooved ball bearing Camshaft bearing width Maximum cam widthOil supply holes for the sleeve bearingss508_072 Inlet camshaftOil supply to the bearing points The sleeve bearings are supplied with oil from oil supply holes.13Engine MechanicsValve gearThe inlet valves are installed at an angle of 21°, and the exhaust valves at an angle of 22.4°, arranged overhead in the combustion chamber. The valves are actuated by roller rocker fingers.Other features The valve stems have a diameter of 5 mm. The valve seat angle is 90° on the inlet side and 120° on the exhaust side, which increases their resistance to wear when alternative fuels are used (e.g. for natural gas). Roller rocker fingers508_031Variable valve timingA continuously variable inlet camshaft adjustment for a crankshaft angle of up to 42° has been utilised. A vane-type adjuster on the inlet camshaft carries out the adjustment according to the engine load and speed. The vane-type adjuster is adjusted by the valve for variable valve timing, which is integrated directly into the oil circuit. The adjustment angle is measured using the Hall sender G40. The variable valve timing results in: - Very good inner exhaust gas recirculation, which lowers the combustion temperature along with the nitrogen oxide emissions - An improved the torque band.Exhaust valveInlet valveValve for variable valve timing N205Hall sensor G40Vane-type adjuster with securing bolts508_058The securing bolt is situated behind a plug and has a right-hand thread.14Oil supplyThe oil supply for the bearing points, the piston cooling nozzles, the variable valve timing and the valve gear is supplied using a duocentric oil pump. It has been installed on the poly V-belt side as a crankshaft oil pump to save space. This means the inner rotor is found directly on the front pivot area of the crankshaft and is driven by it directly. The advantages of this design are the low friction, low weight and low drive noises.s508_076 Return line Duocentric oil pump Inner rotor Outer rotor s508_083 Piston cooling nozzles Oil pressure switch F1 Supply line Oil filter Pressure control valve Pressure control valve Oil suction pipePressure control valve The pressure control valve is integrated into the oil pump housing and regulates the oil pressure to approx. 3.5 bar. This prevents the oil pressure from increasing too rapidly, for example when the engine is started, which damages the gaskets.Oil pressure switch F1 The oil pressure switch is screwed into the cylinder head. If the oil pressure is less than 0.5 bar, the switch will open and the oil pressure warning lamp K3 lights up.Oil filter The oil filter is installed on the oil sump. A diaphragm valve in the oil filter prevents the oil from escaping from the oil filter when the engine is not running.Piston cooling nozzles The piston cooling nozzles are used to squirt oil onto the underside of the pistons, thereby cooling them.15Engine MechanicsCrankcase breather and ventilation systemThe crankcase breather and ventilation system must ensure that: The formation of condensation in the oil remains low on short trips and therefore prevents the crankcase breather from freezing, Oil vapour and uncombusted hydrocarbons are prevented from being emitted into the environment under all operating conditions.To achieve this, a pressure-controlled system featuring forced ventilation is used.Non-return valve on the camshaft housingIntake manifold connectionOil separator with pressure control valveOil drained from the oil separator into the oil sumps508_075Crankcase ventilation systemThe crankcase ventilation system allows the crankcase to be flushed, therefore reducing the formation of condensation in the oil. It is ventilated with fresh air using a hose leading from the air filter to the non-return valve, which is installed in the camshaft housing. The non-return valve prevents oil or unfiltered blow-by gases from entering into the air filter.16Crankcase breatherThe crankcase is ventilated internally, meaning gases containing oil flow through ducts in the cylinder block to the intake manifold and are distributed evenly among the cylinders there. The oil vapours are cleaned in the oil separator. This is made of plastic and is screwed to the cylinder block.Coarse oil and oil mist separation The gases flow from the crankcase into the oil separator. In the coarse oil separator, the large drops of oil are first separated from the gases by baffle plates and swirl ports. The finer oil mist is then separated in swirl ports in the oil mist separator.Diaphragm valves Pulsations in the intake manifold produce waves of pressure which flow back from the intake manifold to the oil separator. To dampen this pressure, one valve opens first, before the second one opens. This is an effective method of reducing pressure.Pressure control valve The pressure control valve ensures the vacuum in the crankcase remains constant. This ensures that, on the one hand, fresh air is continually drawn in, and on the other hand, that the pressure cannot increase so far that the gaskets could be damaged.Bypass valve If the pressure in the crankcase does increase so much that the gases can no longer be discharged through the swirl ports, the bypass valve opens.Inlet opening Oil mist separation Coarse oil separationSeparation chamber outletOil separator housing cover Pressure control valve Diaphragm valve Bypass valve Diaphragm valveOil return lines s508_074 Separation chamber in the crankcase17Engine MechanicsIntake systemThe intake system comprises the intake manifold with a resonance chamber, the air filter, the throttle valve module, the intake manifold, and the inlet ports in the cylinder head. The plastic inlet pipe, heat welded from four parts, has been designed as a “screw-shaped intake manifold”. This design makes it possible to fit a pipe of 550 mm, required for a good torque band, into the installation space available. The inlet ports provide good air flow control with low engine speeds.Air filterIntake manifold with resonance chamberCylinder headThrottle valve module J338Intake manifold pressure sender G71 and Intake air temperature sender G42Intake manifolds508_07818Intake manifold with resonance chamberDuring the intake process, vibrations are produced in the intake system which will cause different types of noises according to their frequency. However, to keep these noises as inaudible as possible, there is a resonance chamber in the intake manifold which helps reduce the volume of the noises.Intake manifold without resonance chamberWhen there is an intake manifold without a resonance chamber, the intake of fresh air produces vibrations which can result in annoying noises.Vibrations from the intake manifoldIntake manifold oscillationss508_084 Pressure change in the intake connecting pipeIntake manifold with resonance chamberResonance chamberWhen there is an intake manifold with a resonance chamber, the same vibrations are produced during intake. However, the air that has been drawn in now causes the air in the resonance chamber to vibrate. Its vibrations have a similar frequency to the vibrations of the intake manifold, which induce the intake noises. By overlaying both frequencies, annoying noises are reduced.Resonance chamber oscillationsIntake manifold oscillationss508_08519Engine MechanicsCooling systemThe cooling system was completely redesigned from scratch, and was adapted to the installation space available in the up! The coolant pumps and their drive are now on the gearbox side, and the coolant expansion tank has been relocated to the front end. Special features of the cooling system: Dual-circuit cooling system for different coolant temperatures in the cylinder head and cylinder block Cross-flow cooling in the cylinder head (from the inlet side to the outlet side) for a more uniform temperature distribution Thermostat housing with integrated coolant pump Coolant pump driven by the exhaust camshaft using a toothed belt Coolant expansion tank installed at the front end Cooling for the integrated exhaust manifold11 2 3Heat exchanger for heater Exhaust manifold cooling system Cylinder head cooling system Cylinder block cooling system Coolant pump Thermostat 1 for cylinder head (87 °C) Coolant expansion tank Thermostat 2 for cylinder block (103 °C) Coolant controller housing Radiator2 3 44 5 6 5 6 7 8 9 7 9 8 1010s508_06120Thermostat housing with integrated coolant pumpThe thermostat housing is installed on the cylinder head on the gearbox side. The coolant pump has been integrated into the thermostat housing to produce the most compact module possible. The coolant pump is driven by the exhaust camshaft via a maintenance-free toothed belt.Drive wheel on the exhaust camshaftToothed belt guard for the coolant pump driveCoolant pumps508_086Before removing the drive wheel, and when tensioning the toothed belt, you must pay attention to the notes in ELSA. Only a correctly tensioned toothed belt will ensure the coolant pump functions long-term without fail.Thermostats in the thermostat housingThe two thermostats for the dual-circuit cooling system are installed in the thermostat housing. Thermostat 1 for cylinder head It opens at a temperature of 87 °C or above, and opens the path from the radiator to the coolant pump. Thermostat 2 for cylinder block It opens at a temperature of 103 °C or above, and opens the path for the warm coolant from the cylinder block to the radiator. The entire coolant circuit is open.Coolant pump Thermostat 2 for cylinder blockThermostat 1 for cylinder heads508_07921Engine MechanicsFuel systemA non-return fuel system is used in the up! This means there is no fuel return line from the fuel rail to the fuel tank. The fuel is pumped from the fuel delivery unit to the fuel rail and the injectors at a pressure of approximately 3 bar.Fuel system near the fuel tankIt consists of the following components: - The fuel tank, which is made of plastic, and has a capacity of 35 litres. - The fuel delivery unit with its integrated fuel filter and fuel pressure regulator (approx. 3 bar). - The activated charcoal filter, which can be removed after lowering the fuel tank.Activated charcoal filters508_053Fuel delivery unit GX1Fuel system near the engineIt consists of the following components: - The 4-hole injectors, which are inserted into the intake manifold and are therefore nowhere near the “hot” cylinder head. This stops steam bubbles from forming in the valves, making fuel pressure of around 3 bar sufficient. This reduces the energy needed by the electric fuel pump. - The fuel rail is made of plastic, which is screwed onto the intake manifold together with the injectors. The bleeder valve is not required. - The solenoid valve for the activated charcoal filter N80, which is clamped onto the intake manifold. InjectorsFuel railSolenoid valve for active charcoal filter N80You can find further information on the non-return fuel system in the self-study programme no. 260 “The 1.2 l 3-cylinder Petrol Engine”.22s508_054Exhaust systemThe exhaust system comprises an exhaust manifold integrated into the cylinder head, a discrete-level lambda probe upstream of the catalytic converter, a close-coupled three-way catalytic converter, a discrete-level lambda probe downstream of the catalytic converter, a damper element and a main silencer.Lambda probe G39 Three-way catalytic converter Main silencerLambda probe downstream of the catalytic converter G130Damper elements508_064Mixture regulation and catalytic converter monitoring The two discrete-level lambda probes regulate the mixture and monitor the catalytic converter. Enhancements to the software in the engine control unit make it possible to eliminate the usual wideband lambda probes used upstream of the catalytic converter, allowing them to be replaced with a simple and less expensive discrete-level lambda probe. The rear discrete-level lambda probe monitors the function of the catalytic converter.23Engine ManagementSystem overviewBosch Motronic ME 17.05.20, Basic equipmentIntake manifold pressure sender G71 Intake air temperature sender G42Engine speed sensor G28 Electronic power control fault lamp K132Hall sensor G40Throttle valve control module J338 Throttle valve drive angle sender 1 + 2 for electric throttle G187, G188Exhaust emissions warning lamp K83Accelerator pedal module GX2 Accelerator pedal position sender G79 Sender 2 for accelerator pedal position G185Clutch pedal switch F36Control unit in dash panel insert J285 Multifunction display J119Brake light switch FKnock sensor 1 G61Coolant temperature sender G62 Engine control unit J623Lambda probe G39Lambda probe downstream of catalytic converter G130Additional input signals24Power supply relay for Motronic J271Fuel pump relay J17 Fuel delivery unit GX1 Sender for fuel gauge G Fuel pump for pre-feed G6Injector for cylinders 1 - 3 N30, N31, N32Ignition coil 1 up to 3 with output stage N70, N127, N291Onboard supply control unit J519 Diagnostics interface for data bus J533Throttle valve module J338 Throttle valve drive for electronic throttle G186Solenoid valve 1 for active charcoal filter N80Valve 1 for variable valve timing N205Lambda probe heater Z19Lambda probe heater 1 downstream of catalytic converter Z29s508_062Additional output signals25Engine ManagementEngine control unitThe engine control unit is installed between the plenum chamber partition panel and the vehicle battery. It is attached to the battery tray, together with a bracket, by shear bolts. It features two connectors, each with 56 pins. The engine management system used is Bosch Motronic ME 17.5.20. Along with the engine management system's actual functions, it is also responsible for activating the air conditioner compressor and the radiator fan.Battery Direction of travelBattery tray Engine control unit BracketYou will require the 6606/1 isolator box with the test cable VAS 6606/13 to test the wires and components.26s508_088SensorsEngine speed sender G28The engine speed sender is integrated into the sealing flange on the gearbox side, with the flange being, in turn, bolted to the cylinder block. It scans a 60-2 sender wheel in the crankshaft sealing flange. Using these signals, the engine control unit calculates the engine speed and the position of the crankshaft in relation to the camshaft using the Hall sender G40.s508_063 G28 60-2 sender wheelSignal utilisation The calculated injection time, the injection duration and the ignition timing are determined using this signal. It is also used for the variable valve timing.Effects of signal failure If the engine speed sender should fail, the signal from the Hall sender G40 will be used instead. At the same time, the maximum engine speed will be limited to a fixed value and an entry is made in the fault memory.Two different versionsTwo different speed senders are used in the up!: - In the up! with BlueMotion and start-stop function, a speed sender with direction of rotation detection is used - In the up! without BlueMotion, a speed sender without direction of rotation detection is used They cannot be distinguished from the outside at a glance. Only the retaining tabs used to affix them are different. The main difference can be found in the number of hall plates in the sender. The standard sender features two hall plates, while the sender with direction of rotation detection features three.without BlueMotions508_091 G28 with BlueMotion Sealing flange sender wheel module 60-2 sender wheelHall plates27Engine ManagementWhy is there an engine speed sender with direction of rotation detection?In vehicles with a start-stop function, the engine is switched off as often as possible to save fuel. To ensure it starts up again as quickly as possible, the engine control unit must know the exact position of the crankshaft. However, when switched off, the engine does not come to a standstill immediately, but rather keeps turning for a few revolutions. If, before stopping, a piston is just short of the TDC in the compression phase, it is pushed back by the compression pressure. At this moment, the engine rotates to the left. A standard engine speed sender cannot detect this.How it works:Engine speed sensor without direction of rotation detection At the same moment as the two hall plates, the sender detects a rising and a falling gear flank on the sender wheel. Whether the engine is turning to the right or left is something it does not detect. The same signals are sent to the engine control unit, which then assumes that the engine was turning to the right until it came to a standstill. The position it stores can therefore be wrong.Hall plate 12 ms/var.s508_096 Hall plate 2 Sender wheelLow engine speed signalHigh engine speed signals508_094Engine speed sensor with direction of rotation detection Three hall plates are installed for a sender with direction of rotation detection. However, the third plate is in an offset position between the two outer plates. It is decisive for detecting the direction of rotation. While the engine is running, the function is similar to a sender without direction of rotation detection. In this case, the rise and fall of the flank on the sender wheel is detected at the same time. It is only the type of signal which is different.Hall plate 10.2 ms/var.s508_099 Hall plate 2 Hall plate 3Low engine speed signalHigh engine speed signals508_097Different times must be specified on the digital storage oscilloscope (DSO) to ensure the signals from both engine speed senders are displayed correctly.28Direction of rotation detector In order to detect whether the engine is turning to the right or to the left, the timing of the signal sequence from the three hall plates is decisive for detecting a rising flank. When the engine is turning to the right, the sender wheel turns to the left.•Engine is turning to the left When turning to the right, the rising flank is detected by hall plate 1 first. After a short moment, hall plate 3 detects the rising flank and finally hall plate 2. Because the time interval between hall plate 1 and hall plate 3 is shorter than between hall plate 3 and hall plate 2, the fact that the engine is turning to the right is detected. The sender electronics process the signal and send it to the engine control unit with a certain low width. Hall plate 1 s508_1000.2 ms/var.Signal width upon rightward rotationHall plate 2 s508_101 Hall plate 3•Engine is turning to the left When turning to the left, the rising flank is detected by hall plate 2 first. After a short moment, hall plate 3 detects the rising flank and finally hall plate 1. Because the timing of the signal sequence is now the opposite, the fact that the engine is turning to the left is detected. The sender electronics process the signal and send it to the engine control unit with double the low width. Hall plate 10.2 ms/var.s508_102 Hall plate 2 Hall plate 3Double signal width upon leftwards rotations508_103On diesel engines, an engine speed sender without direction of rotation detection is installed. Because diesel engines require a crank angle of at least 180° when starting to build up the necessary compression, an engine speed sender with direction of rotation detection would not provide any benefits. All petrol engines with start-stop function have an engine speed sender installed with direction of rotation detection. This makes a start possible at a crank angle of just 60°.29Engine ManagementIntake manifold pressure sender G71 and intake air temperature sender G42The intake manifold pressure sender and intake air temperature sender are screwed into the intake manifold on the toothed belt side. It measures the pressure and the temperature in the intake manifold.Intake manifold pressure sender G71 with intake air temperature sender G42s508_066Signal utilisation The engine control unit calculates the air mass drawn in using the signals and the engine speed.Effects of signal failure If the intake air temperature sender fails, a fixed substitute value of 20 °C is assumed. If the intake manifold pressure sender fails, a substitute value is calculated from the throttle valve position and the engine speed. In both cases, the fault is recorded in the fault memory.30ActuatorsSingle-spark ignition coils N70, N127 and N291The single-spark ignition coils have been inserted in the middle of the cylinder head, and are only fastened to the camshaft housing by one bolt. The insulation has been enlarged on the ignition coils and the ignition voltage increased. This extends the service life and produces cleaner combustion.Securing bolt Insulation Single spark ignition coils508_080Task The ignition coils have the task of igniting the fuel-air mixture at the right time. The ignition timing is controlled individually for each cylinder.Effects of failure If an ignition coil fails, then the corresponding injector will no longer be activated, resulting in an entry being made in the fault memory.31ServiceSpecial toolsName T10474 Adapter Tool Application For removing and installing the poly V-belt with freewheel on the alternator for vehicles with BlueMotion technology.s508_041 T10475 Counterhold tool Counterhold tool on the vibration damper/crankshaft for undoing and tightening the securing bolt.s508_042 T10476 Assembly tool Assembly aid for positioning the tri-oval camshaft gears precisely.s508_043 T10477 Camshaft fixing device Fixing the camshaft when checking and adjusting the valve timing.s508_044T10478 Assembly toolFor replacing the oil seal for the camshaft (pulley side)s508_04532Name T10479 Assembly toolToolApplication For replacing the oil seal for the camshaft (gear side).s508_046 T10483 Engine bracketRemoving and installing the engine in conjunction with engine and gearbox support V.A.G 1383 A.s508_047 T10485 Assembly tool For replacing the oil seal for the crankshaft (pulley side).s508_048VAS 6606/1 Isolator boxUse for the wire and component test together with test cable VAS 6606/13.s508_10533Test Your KnowledgeWhich answers are correct? One or several of the given answers may be correct. 1. Which statement about the camshaft housing is true?❒ ❒a) The camshafts can be replaced individually. b) The grooved ball bearings in the camshaft housing are secured by a snap ring, and can be replaced individually. c) The camshaft housing and camshafts are installed together in an integral module design. The camshafts cannot be removed.❒2. What advantages does the integrated exhaust manifold offer?❒ ❒a) The coolant is warmed up more quickly by the exhaust gas while the engine is warming up. b) Due to the smaller area of the exhaust gas-side wall surface extending to the catalytic converter, the exhaust gas does not emit as much heat during the warm-up phase, and the catalytic converter is heated up to its operating temperature more quickly by the coolant, despite its cooling effect. c) When the system is operating under full load, the coolant temperature is further reduced, thereby increasing the engine operating temperature range at which lambda = 1. Fuel consumption and exhaust emissions are thus optimised.❒3. Which statements about the cooling system are true?❒ ❒ ❒a) A dual-circuit cooling system is used. b) The coolant pump is integrated into the thermostat housing. c) The coolant pump can be deactivated.344. What must be taken into account when installing the coolant pump for the 1.0 l 44/55 kW MPI engine in the up!?❒a) During installation, the coolant pump must be pretensioned to ensure that the toothed belt is correctly tensioned. b) Before installation, the thread of the screws must be dipped into a new locking and sealing agent. c) Some of the securing bolts have a left-handed thread.❒ ❒5. On which engines is a G28 engine speed sensor fitted with direction of rotation recognition?❒a) The engine speed sender with direction of rotation detection is used in all engines without a start-stop function. b) The engine speed sender with direction of rotation detection has gradually been employed in all engines. c) The sensor with direction of rotation recognition is fitted in all vehicles with petrol engines and start/stop system.❒ ❒Answers: 1. c); 2. a), b), c); 3. a), b); 4. a); 5. c)35508 498© VOLKSWAGEN AG, Wolfsburg All rights reserved. Subject to technical modifications. 000.2812.65.20 Technical status 02/2012 Volkswagen AG After Sales Qualifizierung Service Training VSQ/2 Brieffach 1995 D-38436 Wolfsburg❀ This paper was manufactured using pulp bleached without the use of chlorine..