TECHNICAL DOCUMENTATION

SSP 509 Manual Gearbox 0CF

PDFEN24 pages2 MB
SSP 509 Manual Gearbox 0CF - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingSelf-study Programme Technology 509Manual Gearbox 0CF Design and function The launch of the up! sees Volkswagen offer a new 5-speed manual gearbox.  The manual gearbox 0CF features a compact, lightweight design. It thus meets the main requirements that have been set for the up!. The following goals were achieved during the development of the gearbox: - Greater efficiency - Reduction in weight by optimising all gearbox components - Simple design - Simplification of assembly stepss509_001The self-study programme presents the design and function of  new developments! The content will not be updated.Current testing, setting and repair instructions can be found in the provided service literature.Important note2 ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Volkswagen manual gearboxes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Design and Mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Overview of gearbox design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Input shaft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Output shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Reverse gear. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Differential . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Gearshift components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Gearbox Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 Gearshifts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Transmission of power between input shaft and output shaft . . . . . . . . . . . . . 16Gearbox Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Electronic components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 Special tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Service information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Test Yourself . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .223 IntroductionVolkswagen manual gearboxesEven though they have been around for a long time, manual gearboxes are not outdated technology. They have been adapted to new requirements over and over again. Consequently, manual gearboxes have had a decisive influence on aims such as reducing fuel consumption and noise.Manual gearboxes are and will remain a worthwhile addition for the task of transmitting power from the engine to the drive wheels.Manual gearbox 02Ts509_055 Manual gearbox 08D5-speed manual gearbox 0CF4s509_059s509_058In Volkswagen's gearbox development department, manual gearboxes for a wide range of conditions and requirements in vehicle use have been planned. The spectrum ranges from the manual gearbox 02T for engines that deliver low torques and for compact installation spaces to the manual gearbox 08D for engines that deliver high torques. The manual gearbox 0CF as featured in the up! has now been added to the range. This gearbox covers the needs of the small car segment in particular. Technical dataGearbox code Gearbox type Installation type Installation length/installation width Max. input torque Material used for gearbox and clutch housing Gear oil Initial fill/oil change quantity Weight Spread Final drive ratio Gear pairs Top speed 0CF 5-speed manual gearbox; 2-shaft manual gearbox with additional shaft for reverse gear Front/transverse installation 356 mm/462 mm 120 Nm Aluminium SAE 75 W 1.2 l / 1.1 l 26.7 kg with oil 4.57 both with 44 kW and 55 kW 44 kW: 74 to 19 55 kW: 75 to 18 Identical for 44 kW and 55 kW Reached in 4th gears509_0055 Design and MechanicsOverview of gearbox designSelector fork mechanism  Selector turret with selector shaft  Reversing light switch F4DifferentialGearbox neutral position sender G701Gearbox housingOutput shaft Input shaftClutch housing s509_006The single-piece gearbox housing is joined to the clutch housing which connects the gearbox to the engine.  The selector turret transfers the position of the gear lever to the selector shaft via a cable system.  Inside the gearbox, you will find the input shaft, the output shaft, the reverse gear shaft, the selector fork mechanism, the selector turret with selector shaft and the differential. The reversing light switch F4 screws into the selector turret. The gearbox neutral position sender G701 is only fitted in gearboxes destined for vehicles equipped with the  start/stop system.6 Input shaftDeep-hole bore Tapered roller bearing Tapered roller bearingGear wheel, 1st gear Gear wheel, 2nd gear Gear wheel, 3rd gear s509_057 Gear wheel, reverse gear Gear wheel, 4th gear Gear wheel, 5th gear   Lightweight design of  gear wheels  for 4th and  5th gear 5th 4thDesign The input shaft is mounted in two tapered roller bearings — one in the clutch housing and one in the gearbox housing.  During assembly, the bearings are fitted without preloading. The input shaft and the gear wheels for first, second and reverse gear (fixed wheels) are made from the same piece of metal. The gear wheels for third, fourth and fifth gear are manufactured separately and pressed onto the input shaft. The designs of the fourth and fifth gear wheels along with the input shaft, which has a deep-hole bore, contribute to the reduction in weight. Task The input shaft transfers the output from the engine via the selected gear to the output shaft and differential and then to the front wheels.s509_0607 Design and MechanicsOutput shaftSynchromeshed gear,  2nd gear Tapered roller bearingSynchromeshed gear, 3rd gear  Synchro-hub Synchromeshed gear, 4th gearSynchromeshed gear, 5th gearTapered roller bearing s509_063 Locking collar  for 3rd and  4th gear Hollow  shaft Gear wheel for differential Locking collar for  5th gear and reverse Locking collar  for 1st and  2nd gear Synchromeshed gear, 1st gear Needle bearingsDesign The locking collars with synchro-hubs, synchromeshed gears and the gear wheel for the differential are located on the output shaft. The output shaft has been hollowed out to reduce its weight. It is also equipped with the same tapered roller bearings as the input shaft and is mounted in the clutch and gearbox housings. The shaft is preloaded when it is fitted. The output shaft does not vary in diameter. This means that all synchromeshed gear bearings are identical.  The synchromeshed gears run on needle bearings and have been designed to reduce weight. The first gear and the third, fourth and fifth gears have single synchronisation. The second gear has double synchronisation. The synchro-hubs are identical for first to fourth gears. Task The output shaft produces the different transmission ratios of the individual gears with the aid of its synchromeshed gears.8 Reverse gearGear wheel, reverse gearLocking collar with  outer teeth  for 5th gear and reverses509_010 Intermediate gear  for reverse gearDesign The gear wheel for reverse gear is part of the input shaft. The gear wheel meshes with an intermediate gear that is mounted in the clutch housing on a shaft with a needle cage bearing. Reverse gear is selected via the locking collar that also selects fifth gear. The gear wheel for reverse gear and the intermediate gear wheel for reverse gear are always meshed. Reverse gear is fully engaged only after the locking collar with its outer teeth has been pushed along the output shaft towards the intermediate gear and has meshed with the intermediate gear. Task The intermediate gear for reverse gear reverses the direction of rotation of the output shaft.9 Design and MechanicsDifferentialOutput shaft  Tapered roller bearingDriveshaft bevel gearDifferential housing Tapered roller bearingDifferential bevel gearGear wheel for final drive Rivet s509_011Design In contrast to the 02T manual gearbox, the differential housing is smaller and the gear wheel for final drive is narrower. This has made the differential lighter. The gear wheel for final drive is joined to the differential housing by six rivets.  The differential is mounted on tapered roller bearings on both sides of the housing. Task The differential has the task of compensating for differences in the speed of the inside and outside wheels on one axle, for example, in a curve. This prevents slippage between the tyres and the road.10 Gearshift componentsThe gears are selected via the following components and assemblies: Cable selector system with gear lever Selector turret with selector shaft Selector fork mechanism for output shaftCable selector system with gear levers509_028 Relay lever Selector lever Gear lever Gear selector cable Gear lever module Gate selector cableMountingSelector turret with selector shaft  and assembled relay and selector levers  to which the cables are connectedDesign The cable selector system comprises the gear lever module, a gate selector cable and a gear selector cable with their connections to the selector turret and the mounting for the cables. Task The two cables connect the gear lever and the gearbox. They transfer the selection and shift movements of the gear lever to the selector turret with the aid of the relay lever and the selector lever. The cable selector system also reduces the transfer of vibrations from the drive train to the passenger compartment.11 Design and MechanicsSelector turret with selector shaft2 2 F41 4 6 8 7 Selector turret with sensor plate (9) and gearbox neutral position sender G701 only in vehicles with start/stop system s509_029 5 G701 9 3s509_051DesignThe selector turret comprises: - the selector turret cover (1) with gearbox ventilation (2), gate pin (3) and locking sleeves (4) - the selector shaft (5) - the latching sleeve with gearshift gate and blocking sleeve (6) and the selector finger (7) with recesses (8) - the reversing light switch F4 Task The selector turret transfers the movements of the gear selector cable and the gate selector cable to the selector fork mechanism. The travel of the selector shaft is limited by a gate pin that is fixed in the selector turret cover and extends into the gearshift gate in the latching sleeve. The selector finger on the selector shaft engages in the selector fork mechanism and actuates the selector forks. Recesses in the locking sleeve on the left and right of the selector finger prevent two selector forks being operated at the same time.12 Selector fork mechanismArm Selector shaft Sliding bushingsSelector forkLocking collars s509_050Design The selector fork mechanism consists of the following: - three selector forks with arms and sliding bushings - a selector shaft The ends of the selector shaft are mounted in the clutch and gearbox housings. On the selector shaft are the selector forks, which are moved back and forth along the shaft. The selector forks, which have a fixed connection to the arms, engage in the locking collars and move them. Task The selector fork mechanism transfers the shifting movements of the selector shaft to the locking collars on the output shaft. The locking collars engage in the corresponding synchromeshed gears and thus change the gears.13 Gearbox FunctionGearshiftsDuring gear changes, the selector shaft performs two different movements. The axial movement is produced by the selection gate and the rotary movement by a shift gate inside the gear lever module.Selecting the shift gate with the selection gate  The gate selector cable actuates the relay lever. s509_052 The pivoting of the relay lever converts the pushing and pulling movement of the gate selector cable into an upward and downward movement.  Shift gatesRecess Selector fingerThe relay lever engages in a slot on the selector lever and thus actuates the selector shaft with an upward and downward movement.The axial movement of the selector shaft and the selector finger determines the shift gate.The sideways movement of the gear lever is transferred to the selector turret via the gate selector cable and a relay lever. The relay lever engages in a slot in the selector lever on the selector turret.  This allows the relay lever to lift and lower the selector shaft together with the gearshift gate and the selector finger.This movement allows the selector finger on the selector shaft to engage in one of the three arms.  The recesses on the side of the selector finger prevent the selector finger moving two arms at the same time.14 Selecting the required gear with the shift gate  The pivoting of the selector lever converts the pushing and pulling movement of the gear selector cable into rotary movement. Selector leverGate pin The gear selector cable actuates the selector lever. Selector fingers509_032The selector lever rotates the selector shaft and the selector finger so that the required gear within a shift gate is engaged.Locking pawlThe selection of a gear within a shift gate is performed by the rotary movement of the selector shaft and the selector finger in the selector turret.  The forwards and backwards movement of the gear lever is transferred via the gear selector cable and the selector lever to the selector shaft. Inside the selector turret, the rotary movement of the selector shaft is limited by the gate pin that extends into the gearshift gate.When the gear is selected, the selector finger moves the respective arm on the selector shaft so that the corresponding locking collar on the output shaft engages in the assigned synchromeshed gear. A locking pawl on the gearshift gate prevents reverse gear being selected directly from fifth gear.15 Gearbox functionTransmission of power between input shaft and output shafts509_034s509_0361st gear3rd gear2nd gear4th gears509_03516s509_037 s509_0385th gears509_033Reverse gear Gearbox neutral positions509_03917 Gearbox ManagementElectronic componentsSensorsGearbox neutral position sender G701Location and task The gearbox neutral position sender G701 (neutral gate sensor) is located on the gearbox housing near to the selector turret in vehicles with the start/stop system. The sender measures its distance from a sensor plate on the selector shaft. The measured value is sent as a PWM signal to the engine control unit. The engine control unit recognises that the selector shaft is in the neutral position from the signal.s509_041 G701 Selector shaft with sensor plate Air gap G701 Hall element Distance (air gap) Sensor plate Selector shaft s509_049How it works The gearbox neutral position sender G701 uses the Hall effect principle. The sender measures its distance from a sensor plate on the selector shaft. This distance changes as the selector shaft rotates from the neutral position. A different sized signal voltage is generated in the Hall element depending on the distance measured.18 Small distance s509_048Large distancePWM signalIn other words, the greater the distance between the sender and the sensor plate, the smaller the PWM signal.  If the value of the PWM signal is within the plausible range, the engine control unit recognises that the gearbox is in the neutral position.  If necessary, the engine can now be restarted by the start/stop system without the clutch pedal being depressed (e.g. if the air conditioning is activated or if the battery voltage is too low).Signal sizeEffects of failureDistance Plausible range for neutral position 2nd, 4th, R gear 1st, 3rd, 5th gearIf no signal is detected from the gearbox neutral position sender G701, the start/stop system is deactivated.Behaviour of voltage signal as air gap changesPlease note: The gearbox neutral position sender G701 and the sensor plate are installed only in manual gearboxes for vehicles equipped with a start/stop system. The manual gearbox 0CF for vehicles without a start/stop system does not have this sensor. The selector shaft in the gearbox will also not have a sensor plate in this case. Before the start/stop system is enabled, the engine management uses additional information to check the plausibility of the air gap in the three positions whenever the engine is started again after “ignition off”.19 ServiceSpecial toolsDescription T10027A  Locking pin Tool s509_042 Usage The locking pin is required to correctly adjust the selector mechanism.s509_04410-222A/31-5  Adapters509_047 s509_046 s509_043T10381/1  Closure caps509_045T10481/  T10482  Thrust pieceThe thrust piece is used to drive in the seals for the cardan shafts.The closure caps protect the connecting flange for the drive shafts against damage once the drive shafts have been  disconnected from the gearbox.This adapter is placed over the lid lock and supports the square tube T40091/1.3282/63  Adjustment  plateThe adjustment plate is used to align the manual gearbox 0CF.  It is placed on the gearbox support.3282/64  AdapterThe adapter 3282/64 secures the gearbox during installation and removal.20 Service informationThe gearbox oil must always be drained before the gearbox is removed.  Reason:  When the driveshafts are removed, the gearbox oil will flow out of the housing.PlugMilled pulse generator wheels509_062The plug is bolted onto the clutch housing. The gearbox oil can be topped up here once the plug has been removed. Note for vehicles without ABS:  If a vehicle does not have ABS, the speedometer sender G22 can be fitted in the hole in place of the plug.  The milled pulse generator wheel in the differential housing allows the sender to recognise the gearbox output speed and send it to the control unit in dash panel insert J285 as a speed signal.21 Test YourselfWhich answers are correct? One or several of the given answers may be correct. 1. The manual gearbox 0CF is... a) a 4-speed manual gearbox. b) a semi-automatic 5-speed gearbox with gearbox neutral position recognition. c) a 5-speed manual gearbox.❒ ❒ ❒2.Which weight-reducing measures were used among others in the design of the  manual gearbox 0CF? a) Input shaft with deep-hole bore, hollow output shaft b) Weight-reduced gear wheels for 4th and 5th gear c) Weight-reduced gear wheels for all gears d) Gearbox and clutch housing made from aluminium e) Output shaft and additional shaft made from cold-sintered magnesium silicate f) Only one selector rail for all gears❒ ❒ ❒ ❒ ❒ ❒3.The selector shaft with sensor plate and the gearbox neutral position sender G701 are fitted  when... a) the gearbox is converted into a semi-automatic gearbox. b) the vehicle is equipped with a distance control system. c) the vehicle is delivered with the start/stop system.❒ ❒ ❒22 4.The manual gearbox 0CF is operated via a gear selector cable and a gate selector cable.  Which cable causes which movement on the selector shaft? a) The selector shaft is rotated around its longitudinal axis by the gate selector cable via the selector lever. b) The selector shaft is moved up and down by the gate selector cable via the relay lever and the selector  lever. c) The selector shaft is rotated around its longitudinal axis by the gear selector cable via the selector lever. d) The selector shaft is moved up and down by the gear selector cable via the relay lever and the selector  lever.❒ ❒❒ ❒5.Which movement of the selector shaft causes which action in the gearbox? a) The gear is engaged by the axial movement of the selector shaft. b) The shift gate is selected by the axial movement of the selector shaft. c) The gear is engaged by the rotary movement of the selector shaft. d) The shift gate is selected by the rotary movement of the selector shaft.❒ ❒ ❒ ❒6.The locking pawl on the gearshift gate in the selector dome... a) locks the engaged reverse gear. b) ensures that you can shift into reverse gear only from 1st gear. c) prevents reverse gear being selected directly from 5th gear.❒ ❒ ❒Answers: 1. c); 2. a), b), d); 3. c); 4. b), c); 5. b), c); 6. c)23 509 509© VOLKSWAGEN AG, Wolfsburg All rights reserved. Subject to technical modifications. 000.2812.66.20 Technical status 02/2012 Volkswagen AG After Sales Qualifizierung Service Training VSQ-1 Brieffach 1995 D-38436 Wolfsburg❀ This paper was manufactured using pulp bleached without the use of chlorine.