TECHNICAL DOCUMENTATION

SSP 511 The New EA211 Petrol Engine

PDFEN64 pages4 MB
SSP 511 The New EA211 Petrol Engine - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingSelf-Study Programme 511The New EA211 Petrol Engine Familyun leDesign and functiones, in part or in w l purpos hole ercia , is n m ot comn AG. Volkswagen AG do es n wage s k l ot g o yV ua b ran ed s i tee r o h t or u ac a ssility ab y li an pt cepe rm itte drrectness of i t to the co nform spec a t i h re o n in wit thi sr te o iva r rp fo g ndo c um enht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t . C op yi A new modular strategy has been introduced at Volkswagen with the modular transverse matrix (Modularen Quer Baukasten), or MQB for short. This allows all vehicle modules in the Polo, Golf and Passat classes to use standardised components and modules. A similar modular strategy is now being launched for petrol engines with the new EA211 petrol engine family. This has been called the EA211 modular petrol engine matrix (Modulare Ottomotoren Baukasten). The engines have a capacity of 1.0 l to 1.6 l. The basic engine is a 1.4 l 103 kW TSI engine.es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngAG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s sThe diagram shows a number of details of the new engines which you will become familiar with over the course of the Self-Study Programme and whose design and function are described.thi sd o cu m enility ab y li an pt cerrectness of i t to the co nf o r m spec atio h re n in wits511_776You can find further information about the new engine family in Self-Study Programmes No. 508 “The 1.0 l 44/55 kW MPI Engine with Intake Manifold Injection” and No. 510 “The Active Cylinder Management ACT in the 1.4 l,103 kW TSI Engine”.agen lksw Vo byAG.Prote cted byThe self-study programme presents the design and function of  new developments! The content will not be updated.Current testing, setting and repair instructions can be found in the provided service literature.2ht rig py Co t.c o p yri gh t. C op yiImportant note Contentsswagen AG .V G. Introduction . . . . . . . . . . . . s . .a. .n.A. .o.lk. . . . . . .d.oe .s. . . . . . . . . . . . . . . . . . . . . . . . 4 ge k w n t l o VMatrix MOB. . . . . . . . . . . o y Modular Petrol Engine .g . u.ar.a . . . . . . . . . . . . . . . . . . . 4 b d n ise r o Overview of the EA211 petrol engine family. . . . .te.e o .r . . . . . . . . . . . . . . . . 6 hnew utEngine mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Poly V-belt drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Toothed belt drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Cylinder block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Crankshaft group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Cylinder head. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Camshaft housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Valve gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Variable valve timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Air duct system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Exhaust gas turbocharger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Oil circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Crankcase breather and ventilation system . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Cooling system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41es, in part or in w l purpos hole ercia , is n m ot compe rm itte dun lea ssacility ab y li an pt cerrectness of i t to the co nform spec a t i h re o n in wit thi sr te o iva r rp fo g ndo c um enEngine management system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 System overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Engine control unit J623 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Actuators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 Special tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Test your knowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62AG.ht rig py Co t.agen lksw Vo byProte cted byc o p yri gh t. C op yi3 IntroductionModular Petrol Engine Matrix MOBThe engine installation positions in the vehicleIn the past, the installation position of the engines, for example in the Golf model year 2009, varied widely.  While the previous engine family EA111 with its 1.4 l engines was tilted forwards and the exhaust system faced the front end radiator, the other petrol and diesel engines were installed tilting backwards. The exhaust system was installed facing the bulkhead. In order to take advantage of the full savings potential, all engines using the modular transverse matrix will now have a uniform installation position.  The new installation position of the EA211 engines made an overhaul of the basic engine structure necessary.  The engineers took full advantage of this opportunity, developing a new series of engines in line with the modular strategy. Advantages of the new modular strategy: - Uniform installation position - Standardisation, e.g. of the gearbox connections, cooling system and exhaust system - Compact engine dimensions age Volksw n AG d AG.back - Reduction of the engine depth by 50 mm by tilting the installation w position by 12° agen oeks Vol by d e ris tho u a sss no t gu ara nte eo ra cility ab y li an pt cees, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nGolf 6 EA111  engine familyAdaptations EA211 engine familyMQB All  enginesrrectness of i t to the co nform spec at i h re o n wit in t his Main feature: - Cylinder head rotated by 180°Other  enginess511_1284ht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t . C op yiFurther adaptations: - Exhaust tract  - Drive shaft  - Gearbox  - Gearshiftdo c um en The newly developed EA211 petrol engine familyA multitude of requirements need to be implemented when developing new engines.  At the same time, this provides an opportunity to employ technologies which were too costly to utilise in existing engines. The requirements which have been implemented are: Volkswa y db - Modular structure ise r ho - Rotated installation position of the engines aut s s - Compact design - Reduction in consumption and therefore CO2 emissions by 10 - 20% - Reduction in the engine weight by up to 30% - Compliance with the future EU6 emission standardes, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng. Volkswagen AG gen AG does not gu ara nte eo ra cility ab y li an pt cerrectness of i t to the co nf o r m spec atio h re n in witModular design of the 1.4 l 103 kW TSI engine with Active Cylinder Management Camshaft housingCylinder headIntake manifold with charge air coolerthi sd o cu m enToothed belt driveht rig py Co t.Two-section sump s511_125The attributes shared by all engines in the EA211 family are: • • • • • • Uniform installation position Installation of the air conditioner compressor and the alternator, bolted directly onto the sump or onto the engine block respectively without additional brackets Four-valve technology Aluminium cylinder block Exhaust manifold integrated into the cylinder head Camshaft driven via a toothed beltAG.Cylinder blockagen lksw Vo byExhaust gas turbocharger with electric charge pressure positionerProte cted by c o py rig h t . Co py iAncillary drive5 IntroductionOverview of the new EA211 petrol engine familyThe 1.0 l 44 kW/50 kW/55 kW MPI engine with intake manifold  injectionThis engine was developed especially for the up!  . Volkswagen AG n AG It is available in three power versions, with 44 kW does age ksw not l o V gu y (CHYA), 50 kW (CPGA) and 55 d kW b (CHYB).  ara e nte is r o The 50 kW version is an engine with natural gas drive eo h ut ra a c s for the eco up! s Technical features • Cylinder head with integrated exhaust manifold • Camshafts driven by a toothed belt • Coolant pump integrated into the thermostat housing • Coolant pump driven by a toothed belt from the exhaust camshaft • Inlet camshaft adjustment • Crankshaft oil pump • Single-section aluminium sump • Valves and valve seat inserts for the engine of the eco up! adapted for natural gas fuelurposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pun leility ab y li an pt cerrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um ens511_118Technical dataEngine code Design Displacement Bore Stroke Valves per cylinder Compression ratioagen lksw Vo byht rig py Co t.CHYACPGACHYB3-cylinder inline engine 999 cm3 74.5 mm 76.4 mm 4 11.5:1 50 kW at 6200 rpm 90 Nm at 3000 - 4250 rpm 10.5:1 55 kW at 6200 rpm 95 Nm at 3000 - 4250 rpmTorque and performance diagram[Nm]120 110 100 90 80 7060 50 4030 20s511_121101000 2000 3000 4000 5000 6000[rpm]CHYA 44 kW CPGA 50 kW CHYB 55 kW Emissions standard6AG.Prote cted by c o py rig h t . Co py ir fo ng10.5:1 44 kW at 5000 rpm 95 Nm at 3000 - 4250 rpm[kW]Max. outputMax. torqueEngine management FuelBosch Motronic ME 17.5.20 Super unleaded with RON 95 (Normal unleaded at RON 91 with slight reduction in performance) Three-way catalytic converter, a step-type lambda probe (44/55 kW version), or a broadband lambda probe (50 kW version) before catalytic converter and a steptype lambda probe after the catalytic converter. EU5Exhaust gas  aftertreatment 1.2 l 63/77 kW TSI engine with turbochargerThe 1.2 l TSI engine from the new EA211 petrol engine family is available in two different power versions with 63 kW or 77 kW. The two different power versions is achieved via the software.Technical features • Cylinder head with integrated exhaust manifold • Camshafts driven by a toothed belt • The thermostat housing and the coolant pump form a single unit • Coolant pump driven by a toothed belt from the exhaust camshaft • Turbocharger with electric charge pressure positioner • Inlet camshaft adjustment • Crankshaft oil pump • Two-section sump  (upper and lower section made of aluminium)s511_116Technical dataTorque and performance diagramun leAG. Volkswagen AG d agen oes ksw not l o V gu y b ara Engine code CJZB CJZA d nte ise r o e h t u Design 4-cylinder inline engine or ac a s sility ab y li an pt ceurposes, in part or in wh ole, cial p is n mer m ot p o c s511_122 erm or e t a itte v i r d p[Nm][kW]Displacement Bore Stroke Valves per cylinder Compression ratio Max. output1197 cm3 71 mm 75.6 mm 4 10.5:1 63 kW at 4300 - 5300 rpm 160 Nm at  1400 - 3500 rpm 77 kW at 4500 - 5500 rpm 175 Nm at  1400 - 4000 rpm220 200 180 160 140 120 10080 70 60 50 40 30 20rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enMax. torqueEngine management Fuel Exhaust gas  aftertreatmentBosch Motronic MED 17.5.21 Super unleaded with RON 95 Three-way catalytic converter with one step-type Lambda probe before and one after the catalytic converteragen lksw Vo byCJZB 63 kW CJZA 77 kWAG.Prote cted byEmissions standardEU5ht rig py Co t.1000 2000 3000 4000 5000 6000[rpm]c o p yri gh t. C op yir fo ng7 Introduction1.4 l 90 kW TSI engine with turbochargerThe 1.4 l 90 kW TSI engine is hardly distinguishable from the 1.4 l 103 kW TSI engine on the outside. However, while both power versions feature inlet camshaft adjustment, the 103 kW version features additional exhaust camshaft adjustment.es, in part or in w l purpos hole ercia , is n m ot coms511_117 Technical features n AG. Volkswagen AG do e g a e s no ksw • Cylinder head with integrated exhaust manifold • Turbocharger with t gu electric charge pressure Vol by ara d nte • Camshafts driven by a toothed belt rise positioner eo ho t u ra • The thermostat housing and the coolant pump • Inlet camshaft adjustment a c ss form a single unit • External gear wheel oil pump with two-stage oil • Coolant pump driven by a toothed belt from the pressure regulation exhaust camshaft • Two-section sump  (upper section made of aluminium, lower section made of sheet metal)ility ab y li an pt cepe rm itte dun lerrectness of i t to the co nform spec a t i h re o n in wit thi sTorque and performance diagram260 240 220 200 180 160 140 120 100 [Nm] [kW] 100 90 80 70 60 50 40 30 20Technical dataEngine code Design Displacement Bore Stroke Valves per cylinder Compression ratio Max. outputagen lksw Vo byht rig py Co t.CMBA4-cylinder inline engine 1395 cm3 74.5 mm 80 mm 4r te o iva r rp fo g ndo c um en10.5:1Engine management Fuel Exhaust gas  aftertreatments511_1231000 2000 3000 4000 5000 6000[rpm]Emissions standard8AG.Prote cted byc o p yri gh t . C op yi90 kW at 5000 - 6000 rpm 200 Nm at 1400 - 4000 rpmMax. torqueBosch Motronic MED 17.5.21 Super unleaded with RON 95 Three-way catalytic converter with one step-type Lambda probe before and one after the catalytic converter EU5 1.4 l 103 kW TSI engine with turbochargerThe 1.4 l 103 kW TSI engine is the basic engine in the new EA211 petrol engine family. It is available in two versions, with and without Active Cylinder Management (ACT). The power and the torque are the same in both versions.n AG. Volkswagen AG do es n wage s k l ot g Vo y ua b Technical features ran ed s i tee r o • Cylinder head with integrateduexhaust manifold th or ac a s s • Camshafts driven by a toothed beltes, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nility ab y li an pt ce• • •The thermostat housing and the coolant pump form a single unit Coolant pump driven by a toothed belt from the exhaust camshaft Turbocharger with electric charge pressure positioners511_117• • •Inlet and exhaust camshaft adjustment External gear wheel oil pump with two-stage oil pressure regulation Two-section sump (upper section made of aluminium, lower section made of sheet metal)rrectness of i t to the co nform spec at i h re o n wit in t hisTorque and performance diagram[Nm] 280 260 240 220 200 180 160 140 120 100 [kW] 110Technical dataEngine code Design100 90 80 70 60 50 40 30 20CHPACPTA with ACT4-cylinder inline engine 1395 cm3 74.5 mm 80 mm 4 10.0:1do c um enDisplacement Boreagen lksw Vo byht rig py Co t.Compression ratio Max. output Max. torque Engine management Fuel s511_124 Exhaust gas  aftertreatment1000 2000 3000 4000 5000 6000[rpm]Emissions standardAG.Prote cted byc o p yri gh t . C op yiStrokeValves per cylinder103 kW at 4500 - 6000 rpm 250 Nm at 1500 - 3500 rpm Bosch Motronic MED 17.5.21 Super unleaded with RON 95 Three-way catalytic converter with one upstream broadband Lambda probe and one step-type Lambda probe downstream of the catalytic converter EU5 EU69 IntroductionThe EA211 engines with intake manifold injection or  for alternative drive systems1.4 l 66 kW / 1.6 l 81 kW MPI engine with intake manifold injectionThese engines with the engine codes CKAA (66 kW) and CPDA (81 kW) were developed for the markets AG. Volkswagen AG d agen oes ksw not l o V outside Europe.  gu y b ara d e nte The first use of the 1.6 l 81 kW MPI engine is in horis eo t u ra a China. c s s Technical features • Camshafts driven by a toothed belt • Camshaft housing features a modular design • Cylinder head with integrated exhaust manifold • Coolant pump integrated into the thermostat housing • Coolant pump driven by a toothed belt from the exhaust camshaft • Inlet camshaft adjustmentes, in part or in w l purpos hole ercia , is n m ot comility ab y li an pt cepe rm itte dun lerrectness of i t to the co nform spec a t i h re o n in wit thi ss511_1291.4 l 81 kW TGI engine (natural gas)r te o iva r rp fo g ndo c um enTechnical features • One engine control unit for natural gas and petrol operation • Electronic gas pressure regulator with a mechanical pressure reduction level • Optimised gas injection valve, allowing a start from -10 °C in natural gas operation • Valve seat inserts reinforced, hard-faced inlet valves, valve stem oil seals with a second sealing lip, resulting in forced lubrication of the valve stem in the valve guides10ht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t. C op yiThis engine with the engine code CPWA is being used in the Golf 2013. It features a bivalent natural gas drive. The only difference to the 1.4 l 90 kW TSI engine is the additional components for the natural gas drive.s511_117 1.4 l 90 kW TSI Multifuel engineThis engine, with the engine code CPVA, is being used in the Golf 2013 in Sweden and Finland. Technical features • Compatible with up to 85% bioethanol • Fuel quality sender for identifying the proportion of bioethanol in the fuel • Electric engine preheating element in the cooling system • Valve seat inserts reinforced, hard-faced inlet valves, valve stem oil seals with a second sealing lip, resulting in forced lubrication of the valve stem in the valve guidess511_1171.4 l 110 kW TSI engineThis engine is being used in the Jetta Hybrid with the engine codes CRJA (Europe) and CNLA (North American region, NAR). The basic engine is the 1.4 l 103 kW TSI engine. Technical features • Crankshaft with teeth for connecting to the threephase current drive VX54 (electric drive motor) • Vibration damper on crankshaft • Cylinder block and sealing flange on gearbox side with leadthroughs for coolant for cooling the electric drive motor V141 as well as hydraulic fluid for activating the disengagement clutch K0 • Electric air conditioner compressor • Alternator and starter functions are carried out by the electric drive motor V141 • Secondary air system (NAR) • Performance increase to 110 kW with the aid of software modificationsProte cted byes, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngAG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t Hybrid u ra a c s sility ab y li an pt cerrectness of i t to the co nf o r m spec atio h re n in wits511_119•Changes to materials used for lines for the crankcase breather, as well as the fuel and activated charcoal receptacle system, due to emission regulations (NAR)thi sd o cu m enht rig py Co t.agen lksw Vo byAG.c o p yri gh t. C op yi11 Engine mechanicsPoly V-belt driveDepending on the engine and the equipment installed, there are three versions of the poly V-belt drive.  They are generally driven by a six-rib poly V-belt. In all engines, the belt pulley on the crankshaft is equipped with a vibration damper to ensure the engine runs quietly. The ancillaries are bolted directly onto the cylinder block and the sump in order to save space.  No additional brackets are necessary. Poly V-belt Automatic Alternator  tensioning roller pulleyThe air conditioner compressor and the alternator are driven electrically in the 1.4 l 110 kW TSI engine in the Jetta Hybrid. There is no poly V-belt drive.s511_130Crankshaft pulley with  vibration damperVersions of the poly V-belt driveTensioning of the poly V-belt drive by ...un lepe rm itte dn AG. Volkswagen AG do es n wage s k l ot g o yV ua b ran ed s i tee r o h t or u ac a ss Air conditioner compressor pulleyility ab y li an pt ce3-cylinder engine with intake manifold injection MPI4-cylinder engine with direct injection TSIes, in part or in w l purpos hole ercia , is n m ot comrrectness of i t to the co nform spec a t i h re o n in wit thi sA flexible and tensile  poly V-belt without tensioning roller- without A/C compressor - without BlueMotion  technology----s511_131 - with A/C compressor - without BlueMotion  technology ----A rigid tensioning rollerr te o iva r rp fo g ndo c um ens511_132ht rig py Co t.s511_13312agen lksw Vo byAG.Prote cted byc o p yri gh t . C op yiAn automatic tensioning roller- with BlueMotion  - with BlueMotion  technology technology - independent of whether  - independent of whether  an air conditioner  an air conditioner  compressor is installed compressor is installed Toothed belt driveThe camshafts are driven by a maintenance-free toothed belt. It is tensioned using an automatic tensioning roller, which uses contact shoulders at the same time to guide the toothed belt. An idler roller on the tension side and the special shape of the camshaft sprockets in the 3-cylinder engine, or camshaft gearwheel in the 4-cylinder engine respectively, ensure that the toothed belt runs smoothly.1.4 l 103 kW TSI engine Gear wheel exhaust camshaft with camshaft adjuster Gear wheel inlet camshaft camshaft with camshaft adjusterAutomatic tensioning roller Idler roller CTC crankshaft sprocket  (in 1.2 l and 1.4 l engines) s511_103Engine versions Gear wheel 3-cylinder  enginesEffectses, in part or in w l purpos hole ercia , is n m ot compe rm itte dun lea ssTri-oval  A certain amount of force is required to open the valves of a cylinder. This force also swatoothed olkthe gen AG belt drive every time the valve is opened, and at higher speeds will G. V nA camshaft  acts on e g does a w s k not l o sprockets cause it to vibrate. To minimise the strong vibrations which are typical for 3-cylinder V gu y b ara d e engines in particular, special camshaft gears have been employed. It has been n s i te r ho or designed with a larger radius, at e intervals of 120° (tri-oval). utacility ab y li an pt cerrectness of i t to the co nform spec a t i h re o n in wit thi s4-cylinder  enginesOval  CTC crankshaft  sprocketA so-called CTC crankshaft sprocket is installed in the 4-cylinder engines. CTC is an abbreviation which stands for Crankshaft Torsionals Cancellation, meaning the tensile forces and vibrations from the crankshaft are reduced.  During the working stroke, the toothed belt is slackened slightly due to its smaller radius. This reduces the tensile forces and lowers the vibrations of the toothed belt drive.Advantages - The lower toothed belt forces allow the tension force of the tensioning roller to be reduced.  This results in lower friction and mechanical stress on the entire toothed belt drive. - The reduced level of vibrations allows the toothed belt drive to run even more quietly.r te o iva r rp fo g ndo c um enht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t . C op yi13 Engine mechanicsCylinder blockThe cylinder block consists of cast aluminium and has been designed as an open-deck version. Open deck means that it has no webs between the outer wall of the cylinder block and the cylinder liners. The has the advantage of: - not allowing air bubbles to form in this area, which would lead to ventilation and cooling problems-cylinder deformation is kept low when the cylinder head is bolted to the cylinder block. The piston rings can easily compensate this low level of cylinder liner deformation, and the consumption of oil is reduced.es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nAG. Volkswagen AG d agen oes ksw not l o g The galleries for the oil pressure supply, the oil return pipes and yV ua the crankcase breather have been cast into the b d ran e s i tee r cylinder block. This the number of additional components as well as the amount of machining required. o hreduces t or u ac a s sility ab y li an pt cerrectness of i t to the co nform spec at i h re o n wit in t hisCylinder liners Oil returnCylinder barrel Duct for internal crankcase breatherCylinder blockdo c um enGrey cast iron cylinder liners The grey cast iron cylinder liners are individually cast into the cylinder block. Their outer surface is very coarse, which increases the surface area and improves the transfer of heat to the cylinder block.14agen lksw Vo byOil supplyAG.In addition, this ensures that there is a firm fit between the cylinder block and the cylinder liner.ht rig py Co t.Prote cted by c o py rig h t . Co py iUntreated cast surfaces511_015 Crankcase breather Crankshaft groupThe crankshaft group was designed for low, moving masses and low friction. The weight of the crankshafts, conrods and the pistons has been so well optimised that the balancer shaft, otherwise standard in three-cylinder engines, could be omitted.Upper conrod bearing with trapezoidal shape PistonsPiston and  oil scraper ringsConrodHollow-bored conrod journalsCrankshaft Cracked conrod  (conrod and conrod bearing cap) with bearing shellss511_139es, in part or in w l purpos hole ercia , is n m ot comConrod The conrods are fracture-split. In the area subject to a lower load, the upper conrod bearing has a trapezoidal design. This reduces the weight and the friction even further.pe rm itte dun leby ed ris o th au ssAG. Volkswagen AG d agen oes ksw not l o Vgu ara nte eo ra cht rig py Co t.Pistons, piston rings, piston pins The pistons are made from die-cast aluminium. The piston crown features a flat design, because a wall guide for the inner mixture formation, normally standard in the EA111 engines, has been eliminated. Along with reduced weight, the combustion heat is also distributed over the piston crown more evenly, and misfires are thus prevented. The installation tolerance of the piston rings was increased, and friction therefore reduced.r te o iva r rp fo g nCrankshafts Cast crankshafts have been used in the MPI engines, which are subject to a lower load, and forged crankshafts have been used in the TSI engines.  Furthermore, they are distinguished by the number of bearing points, the counterweights and the diameters of the main mounting and conrod bearings. In the 1.4 l 103 kW TSI engine, which is subject to a higher load, this is, a forged steel crankshaft. It features five bearings, four counterweights and a main bearing and conrod bearing diameter of 48 mm. To reduce the weight even further, the conrod journals are hollow-bored. Together, these measures reduce the inside forces on the crankshaft and therefore the load on the main bearings.ility ab y li an pt cerrectness of i t to the co nform spec a t i h re o n in wit thi sdo c um enagen lksw Vo byAG.Prote cted by c o py rig ht . C op yi15 Engine mechanicsCylinder headDuring development of the aluminium cylinder head, priority was given to enhanced use of the exhaust gas energy to ensure a fast engine warm-up phase.Technical features4-valve technology Cross-flow cooling Integrated exhaust manifold Designed for alternative fuelsDesignThe cross-flow cylinder head allows the coolant to flow from the inlet side to the exhaust side via the combustion chambers. It is divided into two sections above and below the exhaust manifold. It flows through several ports, absorbing the heat. It flows from the cylinder head into the thermostat housing, mixing with the remaining coolant.Exhaust side swagen AG.by ed Exhaust gas turbocharger ris o th au ssk VolVolkswagen AGdoes not gu ara nte eo ra cIntake sidees, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nCylinder headility ab y li an pt cerrectness of i t to the co nform spec at i h re o n wit in t hisExhaust port Integrated exhaust manifold Lower cooling areaUpper cooling areas511_147Integrated exhaust manifold The four exhaust ports within the cylinder head have been combined into one central flange in the integrated exhaust manifold. The exhaust gas turbocharger is bolted directly onto this flange. This design has several benefits: - The coolant is warmed up by the exhaust gas while the engine is warming up. The engine reaches its operating temperature faster. This reduces fuel consumption, and the vehicle interior can be heated sooner. - Due to the smaller exhaust-side wall surface extending to the catalytic converter, the exhaust gas looses little heat during the warm-up phase. This allows the catalytic converter to heat up to operating temperature faster, despite the cooling effect of the coolant.AG.Prote cted by-When the system is operating at full capacity, the exhaust manifold and the exhaust gas are cooled even more, and the engine can be operated in a larger consumption-optimised and exhaustoptimised lambda=1 range when operating at full capacity.do c um en16ht rig py Co t.agen lksw Vo byc o p yri gh t . C op yi Camshaft housingDesignThe camshaft housing is made of cast aluminium The modular design involves assembling the camshafts directly into the camshaft housing. As the cams no longer have to fit through the bearing points, it is possible to design very small bearings.es, in part or in w l purpos hole ercia , is n m ot compe rm itte dun leAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o e o module. h and, together with the two camshafts, forms an integral ut ra a c s sCamshaft housingHigh pressure fuel pump driveility ab y li an pt cerrectness of i t to the co nform spec a t i h re o n in wit thi sr te o iva r rp fo g ndo c um enBearing point Deep-groove ball bearing CamOil supply holes511_164Advantages of smaller bearing points - lower friction in the bearings and - higher rigidity.Oil supply to the bearing points The sleeve bearings are supplied with oil from oil supply holes.Grooved ball bearing To reduce friction, the first bearing of that particular camshaft, which is subjected to the highest load from the toothed belt drive, is a grooved ball bearing.In the event of a repair, the camshaft housing is replaced together with the camshafts.  The grooved ball bearings are secured by a snap ring, however they cannot be replaced.ht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py is511_15017 Engine mechanicsValve gearurposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pun leAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s sThe EA211 engine family is generally equipped with 4-valve technology. In this family, the inlet valves are installed at an angle of 21°, and the exhaust valves at an angle of 22.4°, arranged overhead of the combustion chamber. The valves are actuated by roller rocker fingers with hydraulic supporting elements.rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enility ab y li an pt ce Hydraulic supporting elementRoller rocker fingersr fo ng Exhaust camshaftht rig py Co t.Prote cted by c o py rig h t . Co py iExhaust valveAdvantages of the 4-valve technology - Good cylinder charging and discharging - High power yield with a small capacity - Low fuel consumption due to high efficiency - High torque and pulling power - Quieter operation18agen lksw Vo byAG.Inlet camshaftInlet valves511_151Other features - The valve stems have been reduced to a diameter of 5 mm. This results in fewer moving masses and fewer friction losses due to lower valve spring forces. - The valve seat angle is 90° on the inlet side and 120° on the exhaust side, which contributes to an increase in the wear resistance for alternative fuels, e.g. natural gas. Variable valve timingAll EA211 engines employ stepless inlet camshaft adjustment, engines with an output of 103 kW or more have stepless exhaust camshaft adjustment as well. The camshaft adjuster directly on the camshafts carries out the adjustment according to the engine load and speed. They are adjusted by the valves for the camshaft adjustment, which are integrated directly in the oil circuit. The two Hall senders are used to identify the adjustment angle. Camshaft control valve 1 N205 (inlet side) Exhaust camshaft control valve 1 N318Hall sender G300 (exhaust side) Hall sender G40  (inlet side)End cover for exhaust camshaft adjuster Plug for inlet camshaft adjusterAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r s511_149 o eo h ut ra a c s sility ab y li an pt ceEngine versionurposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pCamshaft adjustment versionsun leInlet camshaft adjustment Stepless up to a crank angle of 40° Stepless up to a crank angle of 50°Exhaust camshaft adjustmentrrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um en1.0 l 44/50/55 kW MPI engine– –1.2 l 63/77 kW TSI engine and  1.4 l 90 kW TSI engine 1.4 l 103 kW TSI engine  with/without Active Cylinder  ManagementStepless up to a crank angle of 50°Stepless up to a crank angle of 40°r fo ngCamshaft adjuster seals and attachment To ensure no engine oil finds its way onto the toothed belt, the camshaft adjusters are sealed. This is done by a rubber seal on the end cover of the exhaust camshaft adjuster and one on the plug for the inlet camshaft adjuster. Both camshaft adjusters are attached using securing bolts on the camshafts.  Both bolts have a right-handed thread.ht rig py Co t.Prote cted by c o py rig h t . Co py iagen lksw Vo byAG.19 Engine mechanicsInlet and exhaust camshaft adjustmentThe basic design of both camshaft adjusters is identical.Special features of the camshaft adjustersVane-type adjusters The camshaft adjusters function according to the vane-type adjuster principle. Depending on which of the two chambers the oil is guided to, the rotor turns and the camshaft turns with it. The adjustment is stepless.Housing Chamber 1 Chamber 2 RotorAG. Volkswagen AG d Gear wheel agen oes ksw not l o V g y u b ara ed s511_222 nte ris o eo h t u ra a c s ses, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngExhaust camshaft adjuster return If the engine is to start quickly, no residual gases may enter the cylinders. To ensure this happens,  the exhaust camshaft adjuster is locked in the “early position” and the inlet camshaft adjuster is locked in the “late position” when the engine is switched off.  The exhaust camshaft adjuster is set to a position which is opposite to the direction of engine rotation. Due to the large adjustment angle up to a 40° crank angle, the oil pressure alone may not be sufficient enough for this.  A return spring on the exhaust camshaft adjuster assists the oil pressure when being set in the “early position”.ility ab y li an pt ceExhaust camshaft adjusterReturn springrrectness of i t to the co nf o r m spec atio h re n in wits511_223 Adjustment direction for  “Engine off”thi sd o cu m enRotor20agen lksw Vo byAG.Prote cted byLocking When the engine is switched off, the exhaust camshaft adjuster is locked in the early position and the inlet camshaft adjuster is locked in the late position. This prevents adjustment of the camshafts during the engine start, and the engine starts faster. Furthermore, it prevents noises when the engine is starting.Return springht rig py Co t.c o p yri gh t. C op yiGear wheel Housing Locking mechanisms511_268 es, in part or in w l purpos hole ercia , is n m ot compe rm itte dun leAG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s sility ab y li an pt cerrectness of i t to the co nform spec a t i h re o n in wit thi sValve timingThe use of an inlet and exhaust camshaft adjuster allows the valve timing to be optimized to the requirements of the engine. This is because, depending on the engine's operation, different opening and closing times provide important advantages.Valve timing for the exhaust valve Valve timing for the inlet valve 40° in direction of late 50° in direction of earlyr te o iva r rp fo g nValve lift 9 mm Max. adjustment Basic positionMax.  adjustmentht rig py Co t.do c um enBasic positionagen lksw Vo by1 mmBDC TDC BDC25°15°28° 25° 15° 22°14°36° Crank angle [°]Speed/ load rangePressure ratio  intake manifold/ exhaust system Intake manifold  pressure lower than the exhaust back pressure Intake manifold  pressure lower than the exhaust back pressureValve  overlapEffectsIdlingNone- Very few residual gases in the cylinder, producing quiet  running. - Residual gases are drawn out of the exhaust system into  the cylinders.  - The throttle valve is opened further to ensure there is an  adequate supply of fresh air for the torque required. - The engine is dethrottled, the fuel consumption falls. - Fresh air is forced into the cylinders, residual gases are  forced out.  - Due to a low proportion of residual gas, the rated torque  is reached at a low engine speed.  - Improved response by the exhaust gas turbocharger  and reduced tendency to knock. - When pressure ratios are equal, a larger  valve overlap has little benefit. - No residual gases forced back despite high exhaust back  pressure, preventing any disadvantageous mixture  formation.Low speed/ low to medium loadHighLow speed/ high loadIntake manifold  pressure higher than the exhaust back  pressure due to charge pressureHighMedium engine speed/ medium load High speed/ high loadCharge pressure approximately equal to exhaust back pressure Charge pressure lower than the exhaust back pressureLowLows511_148AG.Prote cted byc o p yri gh t. C op yiMax. valve overlap21 Engine mechanicsAir duct systemThe fresh air is guided into the cylinders via the air filter directly on the engine, the exhaust gas turbocharger,  the throttle valve module, the intake manifold with integrated charge air cooler, the inlet ports and the inlet valves.Special features of the air duct system - The intake connecting pipe features resonance chambers which reduce the vibrations produced in the intake system during the intake process. Depending on their frequency, vibrations can lead to a variety of noises. - The inlet ports have been designed to ensure good air flow control with low flow resistance. - The charge air is cooled by a charge air cooler, through which coolant flows, located in the intake manifold. - A nozzle is attached to the air filter in the 1.4 l 103 kW TSI engine with Active Cylinder Management in the Polo Blue GT, in which condensation collects and drips out via a membrane once a certain quantity has been reached. AG. Volkswagenagen ksw Vol y b ed ris o th auAG do es n ot g ua ran tee or aces, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nssExhaust gas turbocharger Air filterility ab y li an pt cerrectness of i t to the co nform spec at i h re o n wit in t hisResonance chamberss511_166do c um enDrainage pipeDiaphragm valves511_16722ht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py iThrottle valve  control unitIntake manifold with integrated charge air cooler Exhaust gas turbochargerAn exhaust gas turbocharger is used for charging in the TSI engines in the EA211 engine family. This was designed for a high torque at low engine speeds and a fast response. This allows the 1.4 l 103 kW TSI engine to reach its maximum torque of 250 Nm at just 1500 rpm.AG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo A special feature of the charge air system is its h ut ra a s compact design. This means the exhaust gas s Exhaust gas turbocharger curposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pCharge air systemility ab y li an pt ceturbocharger has to compress a smaller volume and the required charge pressure is reached faster.un lerrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um ens511_168Exhaust gas turbochargerCharge air coolerEvery exhaust gas turbocharger was newly developed for their respective engine and the corresponding power. While the basic design with the air duct system, the lubrication or the cooling is identical in all versions, they differ in the dimensions of the turbine and compressor wheels. Another difference between them is found in the charge pressure positioners. They can be replaced individually, however the attachment to the wastegate and the basic setting after replacement differ according to the engine.r fo nght rig py Co t.Charge pressure positioner Oil linesAG.Features of the exhaust gas turbocharger: - Small turbine and compressor wheel diameter with correspondingly low moments of mass inertia. - Material designed for a maximum exhaust gas temperature of 950 °C. - Integration into the coolant circuit of the charge air cooling to keep the temperature at the shaft bearings low once the engine has been switched off. - Connection to the oil circuit for lubrication and for cooling the shaft bearings. - Activation of the wastegate for charge pressure control by an electrical charge pressure positioner with integrated position sender.agen lksw Vo byProte cted by c o py rig h t . Co py iWastegate attachment Coolant return Coolant supplys511_225 Exhaust gas turbocharger23 Engine mechanicsCharge pressure positioner V465The advantages of the electric charge pressure  positioner in comparison with the pneumatic charge pressure control solenoid valve are: A fast adjustment time and therefore faster charge pressure build-up. A high actuation force, as a result of which the wastegate remains firmly closed, even in the event of high exhaust gas mass flows, in order to achieve the specified charge pressure. The wastegate can be actuated independently of the charge pressure. This allows it to be opened in the lower engine load/speed range.  The basic charge pressure drops and the engine has less charge cycle work to do. Actuation of the  wastegate flap-Electrical charge pressure positioner with integrated position sender s511_224es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngFurther information on the electrical charge pressure positioner V465 can be found in Self-Study Programme No. 443 “The 1.2 l 77 kW TSI engine with turbocharger”.ility ab y li an pt ceAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s srrectness of i t to the co nf o r m spec atio h re n in witExhaust gas turbocharger versionsEngine version Diameter  turbine wheelDiameter  Max. charge compressor wheel pressure  according to map 36 mm 1.7 bar (63 kW)  1.0 bar (77 kW) 1.8 barCharge pressure positioner  adaptationthi sd o cu m en1.2 l 63 kW/ 77 kW TSI 1.4 l 90 kW TSI33.6 mmFault readerht rig py Co t.37 mm40 mm24AG.1.4 l 103 kW TSI  39.2 mm with/without ACT41 mm2.2 barFault readeragen lksw Vo byProte cted by c o py rig h t . Co py iThreaded rod preset,  vehicle diagnostic tester Oil circuites, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte s i r The oil circuit, which refers to the path taken by the oil when being guided to the engine, is every o h or ut ac a s engines in the new EA211 engine family. ssimilar in allility ab y li an pt ceOil supply camshaftsThere are differences: - according to oil pump type and drive, - according to the oil pressure regulation type - whether an oil cooler is installed and - whether an exhaust gas turbocharger is installed.Oil pressure switch for reduced oil pressure F378 Main oil gallery Oil supply crankshaftrrectness of i t to the co nf o r m spec atio h re n in witthi sd o cu m enThe table shows which oil pump has been used for which engine, how it is driven and how the pressure is regulated.Engine version 1.0 l 44/50/55 kW MPI engine  and  1.2 l 63 kW/77 kW TSI engine Type of oil pump/drive Duocentric oil pump  Driven directly by the crankshaft Type of regulation A pressure regulating valve in the  oil pump housing regulates the oil pressure to a constant pressure of approx. 3.5 bar.  The oil quantity pumped depends on the engine speed.1.4 l 90 kW/103 kW TSI engineExternal gear oil pump  Driven by the crankshaft via a chain driveThe quantity of oil being pumped is adapted by the oil pump according to the load and engine speed. This allows for two-level oil pressure regulation at 1.8 and 3.3 bar respectively.Further information about the duocentric crankshaft oil pump can be found in Self-Study Programmes No. 508 “The 1.0 l 44/55 kW MPI engine with Intake Manifold Injection” and  No. 196 “The 1.4 l 16 V 55 kW Engine”.ht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py is511_170Oil filter25 Engine mechanicsExternal gear oil pumpAn external gear oil pump is being used in the 1.4 l Volkswagen AG n AG. efficient TSI engines. It features very operation does and age ksw not l o V g y contributes to d b fuel savings and CO2 reductions. uara e n is r The oil tpump is bolted onto the upper section of the tee o ho u ra a c sump ss and operates in two pressure stages of approx. 1.8 bar and 3.3 bar depending on the load and engine speed. It is driven by the crankshaft via a maintenance-free chain drive without a chain tensioner. The respective oil pressure is regulated by the oil quantity pumped.un leCrankshaftes, in part or in w l purpos hole ercia , is n m ot compe rm itte dSump (upper section) Sump (bottom section) Oil pump Chain drive Driven by crankshaftr te o iva r rp fo g nAdvantages of the two-level oil pressure and  oil quantity regulation The drive output of the oil pump is lowered because the oil pump only pumps as much oil as is required. Oil degradation is reduced, because less oil is being circulated.[bar] 3.5 3.3 1.8-approx. 1400 rpm4000 rpm 150 Nms511_202Pressure requirements Oil pressure unregulated (1.0 l and 1.2 l engines) Oil pressure regulated in two levels (1.4 l engines) Low pressure stage High pressure stage26s511_246ility ab y li an pt cerrectness of i t to the co nform spec a t i h re o n in wit thi sdo c um enht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py i The components in the two-level oil pressure regulationExternal gear oil pumpThe housing and the housing cover are made of aluminium and feature several control ports for oil pressure regulation. Depending on how the control piston and the slide unit are pressurised with oil from the oil circuit via the control ports, the quantity of oil being pumped and the oil pressure will change. Control piston  Oil strainer  Control portsPump outlet Drive wheel oil pump Slide unitThe control pistones, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngThe oil is actually pumped by two intermeshed gear wheels (pump gears).  One pump gear is located on the drive shaft, which is driven by the crankshaft via a chain.  The second pump gear is located on a shaft which can be moved longitudinally. The pump gear and the shaft form the slide unit.AG. Volkswagen AG d agen oes ksw not l o V gof y ua slide unit at max. oil delivery quantity b unit Position and the slide d ran ise tee r o Control ports h or ut ac a s sility ab y li an pt ceControl piston Pump wheels511_247 ChamberThe slide unit allows an influence to be exerted on the delivery rate and the delivery pressure in the oil circuit.  The position of the slide unit is determined by the pressure ratio acting in the chambers to the left and right of the slide unit.  The pressure ratio depends, in turn, on the activation of the control piston.c o p yri gh t. C op yiSlide unit with  pump gear Position of slide unit at min. oil delivery quantityPump wheels511_248 Chamber Chamber Slide unit with  pump gears511_174rrectness of i t to the co nf o r m spec atio h re n in witthi sd o cu m enht rig py Co t.agen lksw Vo byAG.Prote cted by27 Engine mechanicsValve for oil pressure control N428The valve for oil pressure control is actuated by an earth signal from the engine control unit in accordance with the load and engine speed. A valve is used to switch between the two oil pressure stages by alternately supplying the various control ports of the oil pump with oil. The valve features the following switch states: - If the valve is actuated, it opens the control port to the oil pump and pumps at the low oil pressure stage of 1.8 bar. - If the valve is not actuated, the port is kept closed by spring pressure and the oil pump and pumps at the high oil pressure stage of 3.3 bar.s511_177 Valve for oil pressure control N428Oil pressure switch for reduced oil pressure F378  and oil pressure switch F1AG. Volkswagen AGat The two oil pressure switches allow the engine control unit to monitor the respective oil pressure doe agen the oil pressure s no ksw l o t gu V y stage. If the oil pressure exceeds a certain threshold, thed corresponding oil pressure switch opens b ara and the engine e nte s i r control unit receives a signal. This then transmits a message on the CAN bus and the engine oil pressure warning eo tho u ra a c lamp K3 in the dash panel insert is activated. ssility ab y li an pt ceOil pressure switch for reduced oil pressure F378 It is bolted on the intake side, near the toothed belt in the cylinder head. It is used to determine whether the minimum oil pressure is being achieved.es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g ns511_178rrectness of i t to the co nform spec at i h re o n wit in t hisOil pressure switch F1 It is bolted into the middle of the cylinder block on the exhaust side. If the engine control unit has switched over to the high oil pressure stage, then it is used to monitor the high oil pressure.Oil pressure switch for reduced oil pressure F378s511_228do c um enOil pressure switch F128ht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t. C op yi The oil pressure controlCompared to an unregulated oil pump, the drive power had already been reduced considerably in the regulated ducocentric oil pumps in the EA111 petrol engine family. It only pumped as much oil over the entire engine speed range as was needed to keep the oil pressure at a constant 3.5 bar.  With the new oil pumps for the EA211 engine family, the oil pressure is regulated at two levels depending on the engine speed and load. Above all, in the lower to medium engine speed/load range, the drive power falls as the oil pressure is only approx. 1.8 bar in this case. Less oil therefore has to be pumped by the oil pump.Exhaust camshaft control valve 1 N318urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pun leAG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h Camshaft control valve 1 N205 t u ra a c s sility ab y li an pt ceExhaust camshaft adjuster Lubrication points for camshafts, hydraulic compensation elements and valvesInlet camshaft adjuster Fourfold camsFuel pressure regulatorrrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enExhaust gas turbochargerOil pressure switch for reduced oil pressure F378 Piston coolingOil pressure switch F1Lubrication point for crankshaftOil cooleragen lksw Vo byProte cted byExternal gear oil pumpOil pump drive Return Oil filter Sump Intake fitting s511_180ht rig py Co t.AG.c o p yri gh t. C op yiValve for oil pressure control N428r fo ng29 Engine mechanicsFunctional sequence of the oil pressure regulationThe oil pressure level is set by the oil quantity being pumped. The amount of oil being pumped depends  on the position of the slide unit, how far the two pump gears are apart, and the engine speed.Valve for oil pressure control (activated)a) The valve for oil pressure control is activated by the engine control unit using the earth and opens the control port to chamber 2.pe rm itte db) The control piston is pressed onto the stop of the high pressure stage by the compression spring.es, in part or in w l purpos hole ercia , is n m ot comun len AG. Volkswagen AG do es n wage s k l Chamber ot g o yV u Control piston b d ra2 1a + e nte s i r o eo h t u ra a c ssb Compression spring Pump gearsc) The oil pressure in chambers 3 and 4 totals less than 1.8 bar and has no effect on the position of the slide unit. The compression spring presses the slide unit against the full flow stop.c Chamber 3 Slide unit Stop full flow Pressure-freeht rig py Co t.Chamber 4Compression springr te o iva r rp fo g ns511_249do c um en1.8 baragen lksw Vo byControl pistonCompression spring to chamber 3 Return to chamber 430AG.Prote cted byEngine speed increases When the engine speed increases, the oil pump pumps more oil and the oil pressure increases. At the same time, the pressure in chambers 1 and 2 of the control piston increases, and it is pushed to the left against the spring force. Because the pressure in chambers 3 and 4 of the slide unit still totals less than 1.8 bar, the slide unit remains at the full flow stop.Chamber 2 Chamber 1s511_250Return line to sumpStop  High pressure stagerrectness of i t to the co nform spec a t i h re o n in wit thi sPressure build-up from engine start to  approx. 1.8 bar Once the engine has started, the required oil pressure must be built up as quickly as possible. The two pump gears are exactly opposite each other and the maximum oil quantity at the engine speed is pumped into the oil circuit.to the oil circuit to the oil pump aility ab y li an pt cec o p yri gh t . C op yi Low-pressure stage – approx. 1.8 bar At approx. 1400 rpm, the oil pressure reaches the lower pressure stage of approx. 1.8 bar. This pressure is kept constant up to 400 rpm or 150 Nm respectively. When the engine speed increases, the oil flow quantity and the oil pressure increase; they decrease when the engine speed falls.Oil pressure regulation when the oil pressure  increases to more than 1.8 bar a) The valve for oil pressure control is activated by the engine control unit using the earth and opens the control port to chamber 2. b) The increasing engine speed increases the pressure in chambers 1 and 2 to more than 1.8 bar and the control piston is pushed to the left against the spring force. The path from chamber 4 to the return to the sump is opened. c) The pressure in chamber 3 increases to more than 1.8 bar and pushes the slide unit slightly to the right, against the spring force. The oil from chamber 4 is pressed back into the sump. The pump gears no longer intermesh as much, and the oil quantity being pumped, and therefore the oil pressure, decrease.a Valve for oil pressure control (activated)Control pistonChamber 1 Chamber 2b  Chamber 3 ReturnPump gearsc Slide unit Chamber 4 swagen AG AG. Volk does agen s511_251 ksw not l o gu yV Mesh range of the pump gears b a ran ed tee ris ho t or u Pressure-free ac a ss Low-pressure stage (1.8 bar)ility ab y li an pt ceOil pressure regulation when the oil pressure  falls below 1.8 bar a) The valve for oil pressure control remains open.es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngrrectness of i t to the co nf o r m spec atio h re n in witControl pistonChamber 1 Chamber 2b) When the engine speed decreases, the pressure in chambers 1 and 2 falls below 1.8 bar and the control piston is pushed to the right by the spring force. The path from the oil circuit to chamber 4 of the slide unit is opened.b  Chamber 3 Pump gearsht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig ht . C op yic) The pressure in chambers 3 and 4 is now equal again. Together with the spring force, the slide unit is pushed slightly to the left. The pump gears continue to intermesh, and the oil quantity being pumped, and therefore the oil pressure, increase.c Slide unit Chamber 4s511_269thi sd o cu m en31 Engine mechanicsSwitching over to the high pressure stage – approx. 3.3 bar At an engine speed of 4000 rpm or an engine load of 150 Nm, a switchover to the high pressure stage of approx. 3.3 bar occurs. To reach the higher pressure, the quantity of oil pumped is increased.Switchover position to the high pressure stage a) The valve for oil pressure control is no longer activated by the engine control unit and closes the control port to chamber 2. b)a Valve for oil Control port closed Control pistones, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g npressure control olkswagen AG en AG. V does wag s The lack of oil pressure in chamber 2 allows the k n l ot g (activated) Vo ua by d ran compression spring to push the control piston far e tee ris o h t or to the right, and opens u a large cross section to ac a sschamber 4.bc) The oil pressure in chamber 4 of the slide unit increases and pushes this far to the left together with the compression spring. The two pump gears now intermesh deeply and pump more oil, and the oil pressure increases.to chamber 4  Chamber 3c Slide unit Pressure-freeChamber 4High-pressure stage (3.3 bar)Switching back to the low pressure stage To switch back to a low pressure stage, the valve for oil pressure control is activated again using the earth and it opens the control port to chamber 2. The oil pressure in chambers 1 and 2 pushes the control piston to the left against the spring force, closes the control port to chamber 4 and opens the return line to the sump. This causes the oil pressure in chamber 4 to fall, and the slide unit is pushed to the right by the higher oil pressure in chamber 3. The pump gears intermesh less, and the oil quantity being pumped, and therefore the oil pressure, decrease.do c um enht rig py Co t.32s511_254 Chamber 1 Chamber 2 Returnility ab y li an pt cerrectness of i t to the co nform spec at i h re o n wit in t hisagen lksw Vo byAG.Prote cted byc o p yri gh t . C op yi High-pressure stage – approx. 3.3 bar As with the low pressure stage, the oil pressure is also regulated at a constant 3.3 bar in the high pressure stage. When the engine speed increases, the oil quantity being pumped and the oil pressure also continue to increase.  To keep the oil pressure at a constant 3.3 bar, the quantity of oil being pumped is adjusted. The regulation at a constant oil pressure is carried out the same way as it is for the low pressure stage.AG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e Oil pressure regulation nte iswhen the oil pressure  r o eo th u ra increases to more sthan 3.3 bar a c surposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pa) The valve for oil pressure control is not activated by the engine control unit and closes the control port to chamber 2.un lea Control port closedb) The oil pressure in chamber 1 is now high enough that it pushes the control piston to the left against the force of the spring, and opens the return port from chamber 4 to the sump. c) The pressure in chamber 4 falls, and the slide unit is pushed to the right against the compression spring by the high oil pressure in chamber 3.  The pump gears no longer intermesh as deeply, pumping less oil, and the oil pressure falls to approx. 3.3 bar.r fo ngValve for oil pressure control (activated)Control pistonb Chamber 3cSlide unitht rig py Co t.Chamber 4Pressure-free High-pressure stage (3.3 bar)Oil pressure regulation when the oil pressure  falls below 3.3 bar If the oil pressure falls below 3.3 bar, for example because the engine speed is falling, then the same regulation is carried out as in the low pressure stage. The regulation at a constant pressure is a continual process in both pressure stages: - If the oil pressure is too low, the control port from the oil circuit to chamber 4 opens at the slide unit. The oil flowing in pushes it so that the pump gears intermesh further, more oil is pumped and the oil pressure increases. - If the oil pressure is too high, the return line from chamber 4 to the sump opens. The oil flowing back pushes the slide unit so that the pump gears do not intermesh as far, less oil is pumped and the oil pressure decreases.s511_255  Chamber 1 Chamber 2 Returnility ab y li an pt cerrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enagen lksw Vo byAG.Prote cted by c o py rig ht . C op yi33 Engine mechanicsCrankcase breather and ventilation systemThe crankcase breather and ventilation system must ensure that: - The formation of condensation in the oil remains low on short trips and therefore prevents the crankcase breather from freezing, and AG. Volkswagen AG d agen oes ksw not l o - oil vapour and uncombusted hydrocarbons are prevented under all gu y V from being emitted into the environment b ara d e n s i t r ee operating conditions. hoes, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngt au ssor acility ab y li an pt ceCrankcase breatherNon-return valverrectness of i t to the co nf o r m spec atio h re n in witThe crankcase breather allows the crankcase to be flushed with fresh air, therefore reducing the formation of condensation in the oil. It is ventilated with fresh air using a hose leading from the air filter to the non-return valve on the camshaft housing. The non-return valve prevents oil or unfiltered blowby gases from entering the air filter. If the pressure in the crankcase becomes too high, it opens the path to the air filter. This prevents any damage to seals due to excessive pressures. Connection on the air filters511_234thi sd o cu m enCrankcase ventilationThe gases flow from the crankcase into the oil separator. In the coarse oil separator, the large drops of oil are first separated from the gases by baffle plates and swirl ports, followed by the small drops of oil in the fine oil separator, which are separated by smaller swirl ports. A throttle bore in the housing of the oil separator to the intake manifold limits the throughput when the vacuum in the intake manifold is too high. After the oil separator, the gases reach the inlet point to the intake manifold or to the exhaust gas turbocharger.s511_236 to intake manifoldfrom the  crankcase Oil returnBaffle plates and swirl ports in the housing cover of to exhaust gas the oil separator turbocharger34ht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig ht . C op yis511_235 Discharge of blow-by gases into fresh airThe EA211 engines features an internally guided crankcase breather which prevents any freezing. Internal means that the blow-by gases purified of oil in the oil separator are largely guided to the inlet points within the engine. They mix with fresh air there. In the 1.0 l MPI engines, the gases are drawn into the intake manifold by a vacuum. In the 1.2 l and 1.4 l TSI engines they go directly to the intake manifold or the intake side of the exhaust gas turbocharger, depending on the pressure ratio.urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pturbocharger closes.  The blow-by gases are now sucked into the intake manifold via the hose.un len AG. Volkswagen AG do es n wage s k l ot g o yV ua Vacuum in intake manifold b ran ed s i tee r o The suction effect of the engine makes than that on the h the pressure in the valve in the intake manifold t olower u ra a c intake side of the side of the turbocharger. This opens ss the valve in the intake manifold and the valve on theility ab y li an pt ceintakeCharge pressure in the intake manifold The pressure on the intake side of the turbocharger is lower than in the intake manifold in this case. The valve on the intake side of the turbocharger opens. The valve in the intake manifold closes. The blow-by gases are drawn in directly by the turbocharger.rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enr fo ngs511_237s511_190s511_188Non-return valve on the intake manifoldagen lksw Vo byNon-return valve intake side on the exhaust gas turbochargerAG.Non-return valve in the  intake manifold This is attached to the lowest point of the intake manifold. When the engine is at a standstill, it is open and any oil there can flow back to the separator.ht rig py Co t.Prote cted byc o p yri gh t . C op yi35 Engine mechanicsCooling systemA dual-circuit cooling system is used for engine cooling in all EA211 engines. With this system, the coolant is channelled separately through the cylinder block and cylinder head at different temperatures. The temperature regulation is controlled by two thermostats in the the