TECHNICAL DOCUMENTATION
SSP 534 The 1,4l 3-cylinder TDI Engine

This PDF is currently unavailable.
Read document text
Service TrainingSelf-study Programme 534es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s sility ab y li an pt cerrectness of i t to the co nf o r m spec atio h re n in witThe 1.4 l 3-cylinder TDI Engine in the EA288 Diesel Engine Family Design and Functionthi sd o cu m enht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py iThe latest instalment of the modular diesel matrix has resulted in the development of the new 1.4 l, 3-cylinder TDI engine. It is a member of the EA288 diesel engine family, and is being used for the first time in the Polo 2015. The engine is available in three power versions: 55 kW, 66 kW and 77 kW.AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s sility ab y li an pt cees, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nrrectness of i t to the co nform spec at i h re o n wit in t hisdo c um enFurther information on the EA288 diesel engine family can be found in Self-study Programme no. 514 “The New EA288 Diesel Engine Family” and in Self-study Programme no. 526 “The EA288 Diesel Engine Family with Emission Standard Euro 6”.This Self-study Programme describes the design and function of new developments. The contents will not be updated.For current testing, adjustment and repair instructions, refer to the relevant service literature.2ht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t. C op yis534_010Important noteContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 The 1.4 l, 3-cylinder TDI engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4n AG. Volkswagen AG do es n wage s k l ot g o yV ua b ra ed s i r Engine mechanics . . . . . . . . . . . . . . . . . . . . . . . . . n.te. ... o eo h t u ra a c. Cylinder ss block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng. . . . . . . . . . . . . . . . . . .6 ................... 6 Crankshaft group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Cylinder head. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Balancer shaft module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Toothed belt drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Poly V-belt drive. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Camshaft housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Oil circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Thermal management system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Air duct system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23ility ab y li an pt ceEngine management system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 System overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Engine control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Air regulation system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Dual-circuit exhaust gas recirculation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Charge air cooling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Glow plug system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Exhaust system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40thi sd o cu m enrrectness of i t to the co nf o r m spec atio h re n in witService . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 Special tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Test your knowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43ht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t . C op yi3IntroductionThe 1.4 l, 3-cylinder TDI engineThe new 1.4 l,es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut 3-cylinder TDI engine is a member of the EA288 diesel r aengine a c s sfamily.The focal point during development was based on reducing the weight and also ensuring low fuel consumption and good power delivery. Increasing the power output from 55 kW to 66 kW and 77 kW respectively was achieved by modifying the engine control unit software. The 77 kW engine also features a larger turbocharger.rrectness of i t to the co nform spec at i h re o n wit in t hisility ab y li an pt ceTechnical features-Cylinder block made from aluminium Balancer shaft module with oil and vacuum pump Intake manifold with swirl flaps Water-cooled charge air cooler Switchable coolant pump Dual-circuit exhaust gas recirculation system, comprised of high and low pressure exhaust gas recirculation Injection system with maximum injection pressure of 2000 bardo c um en4ht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py is534_011Technical dataEngine code Design Displacement Bore Stroke Valves per cylinder Compression ratio Firing order Max. output Max. torque Engine management system Fuel Exhaust gas aftertreatment Emission standard 55 kW at 3000 - 3750 rpm 210 Nm at 1500 2000 rpm CUSA CUSB Three cylinder inline engine 1422 cm3 79.5 mm 95.5 mmV by d 16.2:1 ise r tho au 1-2-3 s sCUTA4 wagen AG. Volkswagen AG doe s no olkst gu ara nte eo ra cility ab y li an pt cees, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng66 kW at 3000 - 3250 rpm 230 Nm at 1750 2500 rpm Delphi DCM 6.277 kW at 3500 - 3750 rpm 250 Nm at 1750 2500 rpmrrectness of i t to the co nf o r m spec atio h re n in witDiesel compliant with DIN EN590Dual-circuit exhaust gas recirculation system, oxidation and nitrogen oxide storage catalytic converter, diesel particulate filter EU6Torque and power diagram[Nm]thi sd o cu m en[kW]ht rig py Co t.250200150100501.4 l, 55 kW TDI engine 1.4 l,66 kW TDI engine 1.4 l, 77 kW TDI engine1000 2000 3000 4000 5000 [rpm]0agen lksw Vo byAG.Prote cted by c o py rig ht . C op yi75604530150s534_0695Engine mechanicsCylinder blockTo reduce the weight, the cylinder block was produced using die cast aluminium. Compared to the 1.2 l, 3-cylinder TDI engine block, just changing the material from grey cast iron to aluminium alone resulted a weight reduction of approximately 11 kg. The cylinder liners are made of grey cast iron due to the high loads placed on them. They are fitted into the cylinder block during manufacture by thermal joining. This involves heating the cylinder block and cooling the cylinder liners down to a very low temperature. The principle of using deep-seated cylinder head bolts has been taken from the EA288 diesel engine family. This ensures the forces produced are better distributed throughout the cylinder block structure, therefore improving the distribution of pressure over the cylinder head gasket.Thermally joined grey cast iron cylinder lineres, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngAG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s sDeep-seated cylinder head bolts534_012ility ab y li an pt cerrectness of i t to the co nf o r m spec atio h re n in witDie cast aluminium cylinder blockthi sd o cu m enIt is not possible to rework the cylinder liners because the walls of the liners are too thin.AG.6ht rig py Co t.agen lksw Vo byProte cted byc o p yri gh t. C op yiCrankshaft groupCrankshaftes, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s sThe crankshaft features four bearings and is made of forged steel due to high loads placed on it. It also features two counterweights to compensate for the rotating forces of inertia. The gear sprocket for the balancer shaft module has been shrink-fitted onto the crankshaft side of the 1st cylinder.The crankshaft can be removed and reinstalled. Observe the details in the workshop manual.rrectness of i t to the co nform spec at i h re o n wit in t hisility ab y li an pt cePiston and conrodThe pistons are made of aluminium and feature a piston bowl situated in the middle of the crown. The pistons are cooled by means of piston spray nozzles in the cylinder block. The oil for the spray nozzles for cooling the pistons enters the piston cooling channel, and is used for cooling in the piston ring zone. The conrods are cracked trapezoidal conrods.do c um enht rig py Co t.Aluminium pistons with piston bowl in the middleConrod Spray jets for piston coolingSteel crankshaft Drive sprocket for the balancer shaft module s534_061Drive sprocket for the toothed belt driveagen lksw Vo byAG.Prote cted by c o py rig h t . Co py i7Engine mechanicsCylinder headThe main features of the aluminium cylinder head in the 3-cylinder TDI engine are based on the EA288 4-cylinder engine family. To improve the heating and cooling, the cylinder head features an upper and lower coolant jacket.Technical featuresCylinder head made of aluminium Cross-flow cooling Upper and lower coolant jacket 4-valve technology with roller rocker finger and hydraulic compensation elementsAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s sility ab y li an pt ceCylinder head made of aluminiumes, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g ns534_070do c um enrrectness of i t to the co nform spec at i h re o n wit in t his8AG.Lower coolant jacketUpper coolant jacketht rig py Co t.agen lksw Vo byProte cted by c o py rig h t . Co py iDesignIn comparison to the 4-cylinder engines in the EA288 engine family, the 1.4 l, 3-cylinder TDI engine does not feature a rotated valve star. As a consequence, all inlet valves are installed on the inlet side, and all exhaust valves on the exhaust side. Designing the valves to have a parallel arrangement results in good cylinder filling. Valve gear components such as valves, valve seat inserts, valve springs, valve spring plates, valve guides, valve cotters, roller rocker fingers and hydraulic compensation elements have all been taken from the 4-cylinder engines.Roller rocker finger Compensation elementes, in part or in w l purpos hole ercia , is n m ot compe rm itte dun leAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s sility ab y li an pt ces534_016rrectness of i t to the co nform spec a t i h re o n in wit thi sIntake portInlet valver te o iva r rp fo g ndo c um enht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py iExhaust valveExhaust port9Engine mechanicsBalancer shaft moduleTo optimise space and to keep the level of friction low, a balancer shaft module featuring an integrated oil pump and a vacuum pump has been installed. It is bolted directly to the lower section of the cylinder block and is installed in the oil reservoir in the sump. Each of the balance weights features a plastic cover which prevents the engine oil from foaming. The balancer shaft is driven by a drive sprocket on the crankshaft.Drive sprocket on the crankshaftes, in part or in w l purpos hole ercia , is n m ot compe rm itte dun leAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo th u ra a c s sility ab y li an pt cerrectness of i t to the co nform spec a t i h re o n in wit thi sDrive sprocket for the balancer shaft moduleBalance weight with plastic covers534_017r te o iva r rp fo g ndo c um enPlastic coverBalance weight with plastic coverht rig py Co t.Balancer shaft module with integrated oil and vacuum pumpAG.The drive sprocket of the balancer shaft module features a coating which is used to adjust the tooth backlash. The coating is subject to wear as the service life progresses. Adjusting the tooth flank play is no longer possible when the coating has worn off. This is why the balancer shaft module must be replaced following removal.10agen lksw Vo bySuction pipeProte cted by c o py rig ht . C op yiThe straight-toothed drive sprocket for the balancer shaft module is driven via the crankshaft drive sprocket in the opposite direction of engine rotation, and at the same engine speed. The engine vibrations are reduced by the rotating balance weights on the balancer shaft.rrectness of i t to the co nf o r m spec atio h re n in wites, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngn AG. Volkswagen AG do es n wage s k l ot g o yV ua b ran ed s i tee r o h t or u ac a ssility ab y li an pt ceDrive sprocket on the crankshaft Drive sprocket for the balancer shaft modulethi sd o cu m enHousingPlastic cover Oil pump Vacuum pump Balance weight Balancer shaftMore information about the function of the regulated oil pump and the vacuum pump can be found in in Self-study Programme no. 514 “The New EA288 Diesel Engine Family”.ht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t . C op yis534_01811Engine mechanicsToothed belt drivees, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo th u ra a c s sThe exhaust camshaft, the high-pressure pump for the common rail system and the coolant pump are driven by the toothed belt drive.ility ab y li an pt cerrectness of i t to the co nf o r m spec atio h re n in witExhaust camshaft Inlet camshaftDrive sprocket for the camshaft gearDrive sprocket for the high-pressure pumpthi sd o cu m enCrankshafts534_02012ht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig ht . C op yiIdler roller Drive sprocket for the coolant pump Automatic tensioning roller Toothed beltDrive sprocket on the crankshaftPoly V-belt driveThe alternator and the air conditioner compressor are driven via a poly V-belt. The poly V-belt pulley for the crankshaft is fitted with a vibration damper to ensure the engine runs smoothly. In vehicles with an air conditioning system, the poly V-belt is tensioned by a spring-loaded tensioning roller. Vehicles without an air conditioning system feature a flexible poly V-belt without a tensioning roller.es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s sility ab y li an pt cerrectness of i t to the co nform spec at i h re o n wit in t his Poly V-belt pulley on the crankshaftAlternatorVibration damperdo c um ens534_021ht rig py Co t.Poly V-belt Spring-loaded tensioning rollerAir conditioner compressorAG.Installation situation with a flexible poly V-belt for vehicles without an air conditioner compressors534_022agen lksw Vo byProte cted by c o py rig h t . Co py i13Engine mechanicsCamshaft housingThe inlet camshaft and the exhaust camshaft have been integrated into the camshaft housing. The exhaust camshaft is driven by the toothed belt drive. This in turn drives the inlet camshaft via spur gear teeth. The Hall sender G40 is bolted into the cylinder head cover. The sender wheel features a fixed connection to the exhaust camshaft.es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nAG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s sility ab y li an pt cerrectness of i t to the co nform spec at i h re o n wit in t hisHall sender G40 Cylinder head coverdo c um enGasket Toothed belt sprocket for the camshaft gear Sender wheel for Hall sender G40 Exhaust camshafts534_023 Inlet camshaft Toothed belt Camshaft housing Spur gear teethIn the event of a repair, the camshaft housing is replaced together with the camshafts.14ht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t. C op yiOil circuites, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngThe oil is supplied using an oil pump integrated into the components, the valve gear and the turbocharger are consistently supplied with a sufficient quantity of lubricant. The oil pump has been designed to be regulated, and is operated at two pressure stages.AG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a s balancer shaft module. Its task is to ensure the crankshaft c sility ab y li an pt cerrectness of i t to the co nf o r m spec atio h re n in wit3.8 - 4.2 bar Low pressure stageHigh pressure stage1.8 - 2.0 barPressure requirementsThe oil pressure is regulated using two pressure stages. The change from a low pressure stage (1.8 - 2.0 bar) to a high pressure stage (3.8 - 4.0 bar) occurs at a speed of 3000 rpm.3000 rpms534_052thi sd o cu m enValve for oil pressure control N428 s534_040Oil pump in the balancer shaft modules534_025s534_026ht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py i15Engine mechanicsOil filter moduleThe oil filter module is comprised of the oil cooler, the oil pressure switch F1, the oil filter and the housing. The oil pressure switch is screwed into place and is fixed in position by a retaining clip. The retaining clip may not be removed in order to remove and install the oil pressure switch. The oil pressure switch is connected to the oil circuit by a connecting channel in the housing of the oil filter module. The oil pressure switch is monitored in a pressure range between 0.3 bar and 0.6 bar. Coolant supplyOil coolerOil pressure switch F1 Connecting channel to the oil pressure switchn AG. Volkswagen AG do es n wage s k l ot g o yV ua b ran ed s i tee r o h t or u ac a ssility ab y li an pt cees, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngHousingCoolant drainagerrectness of i t to the co nf o r m spec atio h re n in witOil inletOil drainOil filters534_071The retaining clip must not be removed! Observe the instructions in the workshop manual when working on the oil filter module.ht rig py Co t.thi sd o cu m en16agen lksw Vo byAG.Prote cted byc o p yri gh t . C op yiSumpThe sump features a two-section design. The top section is made of die cast aluminium. The bottom section is produced from steel sheet, and its additional robustness make it suitable for poor road surfaces. AG. Volkswagen AG d agen oes ksw is bolted onto the bottom nosection l The oil level and oil temperature sender G266 of the sump. It uses the ultrasonic o t gu yV b ara d e nte principle to calculate the oil level and ris uses a PTC sensor to measure the oil temperature. A gasket is installed between the top section and bottom section. Four guide sleeves with guide pins have been integrated into the gasket. They make gasket adjustment easier in the event of repairs.es, in part or in w l purpos hole ercia , is n m ot compe rm itte dun letho au s seo ra cility ab y li an pt cerrectness of i t to the co nform spec a t i h re o n in wit thi sr te o iva r rp fo g ndo c um enOil level and oil temperature sender G266ht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig ht . C op yiTop sump section made of die cast aluminium GasketGuide sleeve with guide pin s534_041Bottom sump section made of steel sheet17Engine mechanicsThermal management systemThe coolant circuit consists of three sub-circuits which are the coolant micro-circuit, the high-temperature coolant circuit and the low-temperature coolant circuit.7 3 1 45AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t 8 u ra a c s s6es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ng14 9ility ab y li an pt ce1112213rrectness of i t to the co nf o r m spec atio h re n in wit16 1510s534_044thi sd o cu m enKey1 2 3 4 5 6 7 8Coolant expansion tank Coolant temperature sender G62 Heat exchanger for heater Cylinder headagen lksw Vo byc o p yri gh t. C op yi9ht rig py Co t.Thermostat Radiator Switchable coolant pump Coolant valve for cylinder head N489 Engine oil cooler Charge air cooler Low-temperature coolant circuit radiator Charge air cooling pump V18810 11 12 13 14 15 16Auxiliary pump for heating V488AG.Prote cted byExhaust gas recirculation control motor V338 Cooler for low pressure exhaust gas recirculation Cylinder block18Coolant micro-circuit The coolant flows through the following components: - Heat exchanger for heater (3) - Auxiliary pump for heating V488 (4) - Cylinder head (5) - Exhaust gas recirculation control motor V338 (6) - Cooler for low pressure exhaust gas recirculation (7) - Switchable coolant pump (11) - Coolant valve for cylinder head N489 (12)3 4 5761112s534_053High-temperature coolant circuit In addition to the coolant micro-circuit, the coolant also flows through the following components: - Coolant expansion tank (1) - Coolant temperature sender G62 (2) - Cylinder block (8) - Thermostat (9) - Radiator (10) - Engine oil cooler (13)3 4 1 5 8 11 12 2 1376910es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nLow-temperature coolant circuit The coolant flows through the following components: - Charge air cooler (14) - Low-temperature coolant circuit radiator (15) - Charge air cooling pump V188 (16)s534_074 AG. Volkswagen AG d agen oes ksw not l o gu yV ara db nte ise r o eo h t u ra a c s sility ab y li an pt cerrectness of i t to the co nform spec at i h re o n wit in t his1416 15s534_055Charging and bleeding must be carried out using the cooling system charge unit VW6096 and using the vehicle diagnostic tester together with “Guided Functions”: Always follow the instructions provided in ELSA when working on the cooling system. More detailed information about the function of the coolant circuit can be found in Self-study Programme no. 514 “The New EA288 Diesel Engine Family”.agen lksw Vo byc o p yri gh t. C op yido c um enht rig py Co t.AG.Prote cted by19Engine mechanicsAir duct systemThe compact design of the air duct system allows the turbocharger to respond considerably more quickly. The intake air flows through the following components and into the cylinder: - Air filter - Turbocharger - Water-cooled charge air cooler - Throttle valve module - Intake manifold with swirl flaps - Inlet ports - Inlet valvesAG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s sility ab y li an pt cees, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngTurbocharger Intake airrrectness of i t to the co nf o r m spec atio h re n in witInlet valveIntake manifold with swirl flapsthi sd o cu m enThrottle valve control unit s534_02920ht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t. C op yiWater-cooled charge air coolerTurbochargerThe charge pressure is generated by an adjustable turbocharger, which has been integrated into the exhaust manifold. The adjustable guide vanes on the exhaust gas turbine are adjusted by a vacuum. The engine control unit receives feedback about the position of the guide vanes from the position sender for charge pressure positioner G581 in the charge pressure positioner. The bearings are lubricated and cooled by the engine oil.Charge pressure positioner with vacuum unit and position sender for charge pressure positioner G581Exhaust gas turbineRods for guide vane adjustmentCharge air compressores, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngn AG. Volkswagen AG do es n wage s k l ot g o yV ua b ran ed s i tee r o h t or u ac a ssility ab y li an pt cerrectness of i t to the co nf o r m spec atio h re n in witOil inlet Oil returnExhaust manifolds534_030thi sd o cu m enagen lksw Vo byMore information about the design and function of the turbocharger can be found in Self-study Programme no. 190 “Adjustable Turbocharger”.AG.Prote cted byht rig py Co t.c o p yri gh t . C op yi21Engine mechanics. Volkswagen AG Intake manifold with swirl flaps gen AG does swaemissions. To ensure a good fill level, the swirl flaps are opened when the engine load and the engine speed are high.rrectness of i t to the co nform spec at i h re o n wit in t hisCharge air pressure sender G31 Shaftes, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nk not Vol gu by ara d ntehas been installed. It improves ise Euro 6, an intake manifold with swirl flaps In order to satisfy the emission standard r o eo h t u r a consumption and exhaust a the mixture formation in the combustion chamber at low engine speed. This reduces fuel c s sility ab y li an pt ceIntake manifold housingGasketdo c um enPush rodActuator with vacuum unit s534_073 s534_075 Variable intake manifold position sender G513 Variable intake manifold flap change-over valve N239The swirl flaps are adjusted with the aid of a vacuum. If the swirl flaps need adjustment, then the engine control unit activates the variable intake manifold flap change-over valve N239. The vacuum applied there is transferred up to the vacuum unit on the intake manifold. The vacuum applied adjusts the push rod in the intake manifold. This is in turn connected to the shaft for the swirl flaps. The swirl flaps are adjusted steplessly in accordance with the load and speed up to a coolant temperature of approx. 85 °C. After this coolant temperature is reached, the swirl flaps are fully opened. Effects upon failure If the variable intake manifold flap change-over valve N239 fails, or there is no vacuum, then no adjustment of the swirl flaps occurs. The swirl flaps are opened in both cases.22agen lksw Vo byAG.Prote cted byc o p yri gh t. C op yiSwirl flapht rig py Co t.Fuel systemThe 1.4 l, 3-cylinder TDI engine is equipped with a common rail injection system. The injection system made by the Delphi company uses the high-pressure pump to generate a maximum injection pressure of 2,000 bar, which allows it to supply the injectors with the fuel pressure required. As is normally the case, this is regulated by the engine control unit.Injectors N30 - N32 Fuel pressure sender G247urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pun leAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo th u ra a c s sHigh-pressure accumulator (rail)ility ab y li an pt cerrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um ens534_034 High-pressure pumpFuel pressure control valve N276Fuel metering valve N290r fo nght rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig ht . C op yi23Engine mechanicsOverview of fuel systempe rm itte des, in part or in w l purpos hole ercia , is n m ot comun leAG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s sThis simplified diagram of the design of the fuel system shows the components involved and illustrates the different pressure areas and directions of flow in the fuel system.9 7 8ility ab y li an pt cerrectness of i t to the co nform spec a t i h re o n in wit thi sr te o iva r rp fo g ndo c um en654 10 10 102 1 3 s534_043Key1 2 3 4 5 6 7 8 9 10 Fuel system pressurisation pump G6 Pressure regulator for fuel supply system Fuel filter Fuel temperature sender G81 High-pressure pump Fuel metering valve N290 Fuel pressure control valve N276 High-pressure accumulator (rail) Fuel pressure sender G247 Injectors N30, N31, N32 Fuel high pressure 230 - 2000 bar Fuel supply pressure and fuel return pressure from the injectors approx. 5.8 bar Fuel return pressure 0 - 1 bar24ht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t. C op yiFuel delivery unitThe fuel delivery unit is located directly in the fuel tank. The fuel system pressurisation pump G6, the pressure limiting valve for fuel supply and the fuel gauge sender G have been integrated into it. The fuel system pressurisation pump conveys the fuel to the high-pressure pump. It is an electric, unregulated crescent pump. The initial fuel delivery pressure is set to approx. 5.8 bar by a mechanical pressure limiting valve.n AG. Volkswagen AG do es n wage s k l ot g o yV ua b ran ed s i tee r o h t or u ac a ssility ab y li an pt cees, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngFuel supply Fuel return lineFuel line from the fuel pump to the pressure limiting valverrectness of i t to the co nf o r m spec atio h re n in witConnection to the pressure limiting valveHousingFuel line from the pressure limiting valve to the fuel supplythi sd o cu m enPressure limiting valveagen lksw Vo byAG.Prote cted byFloat gauge with rods for the fuel gauge sender GFilterEffects of failure The engine will not run if the fuel system pressurisation pump G6 fails.ht rig py Co t.c o p yri gh t . C op yiFuel system pressurisation pump G6s534_076Fuel intake25Engine mechanicsHigh-pressure pumpA single-piston high-pressure pump made by the Delphi company has the designation DFP 6.1E. It generates a maximum injection pressure of 2000 bar for injection, and is driven by the toothed belt drive.Overview of the high-pressure pumpes, in part or in w l purpos hole ercia , is n m ot compe rm itte dun leAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s sility ab y li an pt cerrectness of i t to the co nform spec a t i h re o n in wit thi sFuel metering valve N290High-pressure connection with exhaust valveFuel supplyDrive shaftr te o iva r rp fo g nFuel return linedo c um ens534_07926ht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py iDesign and function of the high-pressure pumpThe fuel system pressurisation pump G6 pumps the fuel from the fuel tank and into the housing for the highpressure pump. The fuel metering valve N290 installed in the high-pressure pump regulates the required fuel quantity for the highAG. Volkswagen AG d agen oes w s k not pressure section according to load Vol and speed. gu y b ara d nroller. The pump piston is actuated ise by a drive shaft with double cam and a tee r o h t or u The roller ensures low-friction power transmission. ac saes, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nsility ab y li an pt ceHigh-pressure chamberrrectness of i t to the co nform spec at i h re o n wit in t hisFuel metering valve N290Connection to highpressure accumulator (rail) Pump pistonPump piston spring Fuel return lineRollerdo c um enPump housing s534_047 Drive shaft with double camht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t. C op yi Fuel supply27Engine mechanicsPumping fuel into the high-pressure chamber The fuel metering valve is activated and opened by the engine control unit. When the valve opens, the fuel flows through a bore to the inlet valve. The downwards motion of the pump piston increases the volume of the high-pressure chamber. The difference in pressure this produces in front of the inlet valve and the high-pressure chamber opens the inlet valve. This allows fuel to flow into the high-pressure chamber.High-pressure chamberAG. Volkswagen AG d agen oes ksw not l o VInlet valve Boregu ara nte eo ra cility ab y li an pt ceFuel metering valve N290ise Pump piston ory dburposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pun leth au s sValve openss534_056ht rig py Co t.rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enFuel supply28agen lksw Vo byAG.Prote cted byc o p yri gh t. C op yir fo ngBuilding up fuel pressure The upwards motion of the pump piston reduces the volume of the high-pressure chamber. This causes the pressure in the high-pressure chamber to rise, and the inlet valve closes. If the fuel pressure in the high-pressure chamber is higher than the pressure in the high-pressure accumulator (rail) and higher than the force of the spring-loaded non-return valve, then the highly compressed fuel flows to the high-pressure accumulator and the injectors.AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s sility ab y li an pt ceExhaust valve opensurposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pun lerrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enInlet valve closesFuel metering valve N290Pump pistonr fo ngs534_057Effects of failure of the fuel metering valve N290 The fuel metering valve is open when de-energised. Starting and operating the engine remains possible. The fuel pressure regulating valve N276 is used instead to regulate the fuel pressure. The engine power output is reduced and the engine management system runs in emergency mode.ht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t. C op yi29Engine mechanicsInjectorsThe new 7-hole injector made by Delphi has the designation DFI 1.20. In comparison to the 1.2 l, 3-cylinder TDI engine, the new injectors operate with a positive fuel return line pressure Volkswage n AG d (0 to 1 bar) and no longer operate with a negative fuel return line pressure (-0.1 bar to -0.5 bar). A more powerful AG. agen oes ksw not l o V solenoid has been installed for the conversion to a positive fuel return line pressure. The gumore powerful solenoid by ara ed nte s i r guarantees that the injection time and the commencement of injection can be regulated precisely. o eo th u ra a c s The engine control unit regulates it. sility ab y li an pt ceThe technical features are: - Electrical connection in accordance with VDA (German Automotive Industry Association) - Optimised solenoid valve with a more powerful solenoid - Smaller injector needle diameter - Positive fuel return line pressureurposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pun leConnection to high-pressure accumulator (rail)Connection to the fuel return lineElectrical connection in accordance with VDA (German Automotive Industry Association)ht rig py Co t.Prote cted by c o py rig ht . C op yirrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enr fo ngSolenoid valveInjector springInjector needles534_085s534_08330AG.More powerful solenoidagen lksw Vo bys534_084Injection phase controlurposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pun leThe injection phases distinguish between injection in normal engine operation and injection when the diesel particulate filter and the nitrogen oxide storage catalytic converter are in regeneration mode.rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s sility ab y li an pt ceInjection phases in normal and regeneration modeNormal operation TDCRegeneration mode – warm-up phaser fo ngRegeneration mode – regeneration phaseAG.Pilot injectionsMain injectionPost-injectionsNormal operation In normal operation, the injectors operate with up to 3 injections: - 1 - 2 pilot injections and a main injection.Regeneration mode In regeneration mode, up to 6 injections are carried out: - During the warm-up phase, the injection process consists of 2 pilot injections, a main injection and 2 post-injections. - During the regeneration phase, the injection process consists of 2 pilot injections, a main injection and 3 post-injections.More detailed information about the design and function of the injectors can be found in Self-study Programme no. 465 “The 1.2 l 3-cylinder TDI Engine with Common Rail Fuel Injection System”.ht rig py Co t.agen lksw Vo byProte cted by c o py rig h t . Co py is534_07731Engine management systemSystem overviewEngine speed sender G28 Hall sender G40 Air mass meter G70 Exhaust emissions warning lamp K83 Coolant temperature sender G62 Intake air temperature sender G42 Charge air temperature sender after charge air cooler G811 Charge air pressure sender G31 Diesel particulate filter warning lamp K231 Glow period warning lamp K29Fuel temperature sender G81 Fuel pressure sender G247 Knock sensor 1 G61 Exhaust gas recirculation potentiometer G212 Exhaust gas recirculation potentiometer 2 G466n AG. Volkswagen AG do es n wage s k l ot g o Lambda probe G39 yV ua b ran ed s i tee r o h t or u ac a Lambda probe after catalytic converter G130 ssControl unit in dash panel insert J285Convenience CAN busData bus diagnostic interface J533ility ab y li an pt ceExhaust gas temperature sender 1 G235 Exhaust gas temperature sender 3 G495 Pressure differential sender G505 Exhaust gas pressure sensor 1 G450 Position sender for charge pressure positioner G581 Throttle valve module J338 with throttle valve drive angle senders 1 and 2 for electric throttle G187 and G188urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pun lePowertrain CAN busrrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enVariable intake manifold position sender G513 Exhaust flap control unit J883ht rig py Co t.Internal cylinder pressure sender for cylinder 2 G622 Accelerator position sender G79, acc. pos. sender 2 G185 Brake light switch F32AG.Prote cted byOil pressure switch F1agen lksw Vo byc o p yri gh t . C op yiOil level and oil temperature sender G266r fo ngClutch position sender G476es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nolksw agen Arelay pump n AG. VFuel G do J17 es n wage s k l Fuel system pressurisation pump G6 ot g o V y ua b ran ed s i tee r ho or ut ac a ssInjectors, cylinders 1 - 3 N30, N31, N32ility ab y li an pt ceFuel metering valve N290 Fuel pressure control valve N276Charge pressure control solenoid valve N75Variable intake manifold flap change-over valve N239 Throttle valve module J338 with throttle valve drive for electronic throttle G186Exhaust gas recirculation control motor V338 Exhaust gas recirculation control motor 2 V339 Exhaust flap control unit J883AG.ht rig py Co t.rrectness of i t to the co nform spec at i h re o n wit in t hisdo c um enCharge air cooling pump V188 Auxiliary pump for heating V488 Coolant valve for cylinder head N489 Valve for oil pressure control N428Diagnostic connectorLambda probe heater Z19 Lambda probe heater Z29 Engine control unit J623 Heater element for crankcase breather N79 Automatic glow period control unit J179 Glow plugs 1 - 3 Q10, Q11, Q12 s534_051agen lksw Vo byProte cted byc o p yri gh t . C op yi33Engine management systemEngine control uniturposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pun leThe engine control Delphi. Its designation is Delphi DCM 6.2. Its installation location in the Polo 2015 is on the plenum chamber bulkhead of the engine compartment.ility ab y li an pt ceAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a unit was developed by Volkswagen in collaboration with c s sEngine control unit J623rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um ens534_080r fo ngThe adapter VAG 1598/42 is used for taking measurements at the engine control unit J623.34ht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py is534_048Air regulation system7 816 9 5 2 10 11 4 13 16 17 22 18 2414 3151221 20 19urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pun le. Volkswagen AG 23 gen AG does a ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s ss534_04925ility ab y li an pt cerrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enKey1 2 3 4 5 6 7 8 9 10 11 12Air filter13 14 15 16 17 18 19 20 21 22 23 24 25Position sender for charge pressure positioner G581 Charge pressure control solenoid valve N75 Exhaust turbine with guide vane adjustment Lambda probe G39 Exhaust gas temperature sender 3 G495 Oxidation/nitrogen oxide storage catalytic converter Diesel particulate filter Exhaust gas recirculation cooler Exhaust gas recirculation control motor 2 V339 Pressure differential sender G505 Lambda probe after catalytic converter G130 Exhaust gas pressure sensor 1 G450 Exhaust flap control unit J883ht rig py Co t.Air mass meter G70 Turbocharger compressor Intake air temperature sender G42 Charge air cooler Charge air temperature sender after charge air cooler G811 Throttle valve module J338 Charge air pressure sender G31 Variable intake manifold position sender G513r fo ngVariable intake manifold flap change-over valve N239 Exhaust gas recirculation control motor V338 Exhaust gas temperature sender 1 G235AG.Prote cted byagen lksw Vo byc o p yri gh t. C op yi35Engine management systemDual-circuit exhaust gas recirculationThe 1.4 l, 3-cylinder TDI engine features a dual-circuit exhaust gas recirculation system featuring high-pressure and low-pressure exhaust gas recirculation.n AG. Volkswagen AG do es n wage s k l ot g o yV ua b ran ed s i tee r o h t or u ac a ssThe exhaust gas is removed using an external port directly on the exhaust manifold, and is sent via the exhaust gas recirculation control motor V338, without being cooled, until it reaches the charge air pipe. The hot exhaust gases heat up the charge air and are sent through the intake manifold and into the cylinders together with the charge air. The addition of the hot exhaust gas causes the emission control module to heat up quickly, meaning it is ready for operation sooner. The high pressure exhaust gas recirculation is primarily active when the engine is warming up. The recirculation rate of the high pressure exhaust gas recirculation is regulated by the engine control unit using the exhaust gas recirculation control motor V338.rrectness of i t to the co nf o r m spec atio h re n in wites, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngHigh pressure exhaust gas recirculationIntake portExhaust manifoldht rig py Co t.ility ab y li an pt cethi sd o cu m enIntake manifold Emission control moduleCharge air pipeExternal exhaust gas recirculation duct Exhaust gas recirculation valve with exhaust gas recirculation control motor V33836agen lksw Vo byAG.Prote cted byc o p yri gh t . C op yis534_038Low-pressure exhaust gas recirculationThe low pressure exhaust gas recirculation is active in virtually all operating states. The exhaust is removed directly behind the diesel particulate filter, ensuring it is largely free from particulate matter. It flows through the exhaust gas recirculation radiator, which is installed directly on the emission control module. The cooled exhaust gas then passes the exhaust gas recirculation valve and is introduced into the flow of charge air directly in front of the compressor wheel of the turbocharger. The exhaust gas charge air mix flows through the charge air cooler, arriving in the cylinder via the charge air pipe and the intake manifold.olkswagen AG AG. V The exhaust gas recirculation rate depends on the pressure s difference between the d exhaust gas side and the intake agen oes k w not l o V g ua side. by ran ed te ris o Because this pressure difference changes with the interplay h load on the engine, it has to be regulated. Thiseinvolves t or u ac a ss between the intake-side exhaust gas recirculation valve V339 and the exhaust gas-side exhaust flap control unit J883. The difference in pressure may increase or decrease: - The difference in pressure increases when the throttle valve for the exhaust gas recirculation valve opens further and the throttle valve for the exhaust flap control unit closes further. - The difference in pressure decreases when the throttle valve for the exhaust gas recirculation valve closes further and the throttle valve for the exhaust flap control unit opens further.ility ab y li an pt cees, in part or in w l purpos hole ercia , is n m ot compe rm itte dun lerrectness of i t to the co nform spec a t i h re o n in wit thi sIntake manifoldIntake port Turbochargerr te o iva r rp fo g nOxidisation and nitrogen oxide catalytic converterdo c um enCharge air cooler s534_086Exhaust gas recirculation coolerExhaust gas recirculation valve with exhaust gas recirculation control motor 2 V339Exhaust pipe for the exhaust flap control unit J883ht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig ht . C op yiDiesel particulate filter37Engine management systemCharge air coolingThe water-cooled charge air cooler is located in the charge air system, in front of the throttle valve module. There are coolant ribs with W-shaped fins in the cooling element of the charge air cooler. All components of the cooling element are made of aluminium. The intake air temperature sender G42 is used to identify the intake air temperature. The charge air temperature sender after charge air cooler G811 measures the temperature behind the charge air cooler. If the actual temperature behind the charge air cooler is higher than the target temperature, then the charge air cooling pump V188 is activated as required by the engine control unit.Charge air outleturposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pThrottle valve module J338un leAG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s sility ab y li an pt cerrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enCharge air temperature sender after charge air cooler G811 Cooling elementIntake air temperature sender G42 Charge air inletht rig py Co t.Coolant returnCoolant supply38AG.Coolant ribsagen lksw Vo byProte cted byc o p yri gh t. C op yir fo ngs534_036Glow plug systemThe glow plug system is responsible for ensuring a smooth and environmentally friendly engine start. Within seconds, temperatures of up to 1000 °C are reached on the heat rod of the glow plug. These short warm-up times allow a rapid diesel start of around 2 seconds. The glow plugs capable of post-heating continue to glow for up to 180 seconds after the engine has started, allowing them to reduce the exhaust emissions in the warm-up phase.es n ksw The glow plug with an integrated cylinder pressure sensor V is on cylinder 2. It identifies the actual ot g olinstalled y ua b d r a e nte The information s combustion pressure in the combustion chamber and this to the engine control unit J623. ritransmits eo tho u ra about the actual combustion pressure contributes to precise regulation of the fuel injection. c saAG. Volkswagen AG d agen ourposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pun lesility ab y li an pt cerrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enJ623Q10G28Q11 J179G621J533Prote cted by c o py rig ht . C op yiQ12ht rig py Co t.G62r fo ngJ519J285KeyG28 G62 Engine speed sender Coolant temperature senderG621 Internal cylinder pressure sender for cylinder 2 (integrated in glow plug 2 Q11) J179 Automatic glow period control unit J285 Control unit in dash panel insert J519 Onboard supply control unit J533 Data bus diagnostic interface J623 Engine control unit K29 Q10 Q11 Q12 Warning lamp for glow period Glow plug 1 Glow plug 2 Glow plug 3Detailed information about the glow plugs with integrated cylinder pressure sensor can be found in Self-study Programme no. 526 “The EA288 Diesel Engine Family with Emission Standard Euro 6”.agen lksw Vo bys534_050 K29AG.39Engine management systemExhaust systemThe exhaust system for the 1.4 l, 3-cylinder TDI engine in the Polo 2015 is comprised of the following elements: Turbocharger with integrated exhaust manifold Emission control module comprised of oxidation and nitrogen oxide storage catalytic converter Exhaust flap control unit J883 Rear silencerEmission control moduleTurbocharger with integrated exhaust manifoldFlexible tubeAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s sility ab y li an pt cees, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngRear silencerExhaust flap control unit J883rrectness of i t to the co nf o r m spec atio h re n in witthi sd o cu m ens534_08140ht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py iEmission control moduleThe oxidation and nitrogen oxide storage catalytic converter, as well as the diesel particulate filter, are integrated into the close-coupled emission control module. The emission control module is bolted onto the cylinder head using four retainers on the cylinder block. To ensure that the emission control module is not subject to stress once installed, the retainers feature long holes.Pressure differential sender 2 G524 Pressure differential sender G505Exhaust gas temperature sender 3 G495 Lambda probe G39es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngLambda probe after catalytic converter G130AG. Volkswagen AG d agen oes Oxidation and nitrogen ksw not l o gu yV b ara catalytic oxide storage d e n ris converters tee o tho u ra a c ssility ab y li an pt ceRetainerrrectness of i t to the co nf o r m spec atio h re n in witDiesel particulate filters534_060The design and the function of the oxidation and nitrogen oxide storage catalytic converter, as well as the diesel particulate filter, are described in Self-study Programme no. 514 “The New EA288 Diesel Engine Family” and in Self-study Programme no. 526 “The EA288 Diesel Engine Family with Emission Standard Euro 6”.ht rig py Co t.Prote cted by c o py rig ht . C op yithi sd o cu m enagen lksw Vo byAG.41ServiceSpecial toolsDesignation T10533 Engine support Tool Usage Installing and removing the emission control moduleT10535 Socket wrenchRemoving the intake manifoldT10536 Supportes, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nn AG. Volkswagen AG do es n wage s k l ot g o yV ua b ran Installing and removing the engine ed s i tee r o h t or u ac a ssility ab y li an pt cerrectness of i t to the co nform spec at i h re o n wit in t hisT10537 PullerRemoving the injectorsT10540 AdapterPropping up the engine using support bracket 10222AMdo c um en42ht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t . C op yiAG.agen lksw Vo byProte cted byht rig py Co t.c o p yri gh t . C op yido c um enrrectness of i t to the co nform spec a t i h re o n in wit thi sility ab y li an pt ce1. Name the components of the cooling system.p)n)l)i)g)e)c)a)es, in part or in w l purpos hole ercia , is n m ot coman AG. Volkswagen AG do es n wage s k l ot g o yV ua b ran ed s i tee r o d h t or u ac a ssIecmbhkq)o)m)k)h)f)d)b)ngioTest your knowledgefpr te o iva r rp fo g nqs534_04443 Answers: 1. a) Coolant expansion tank, b) Coolant temperature sender G62, c) Heat exchanger for heater, d) Auxiliary pump for heating V488, e) Cylinder head, f) Exhaust gas recirculation control motor V338, g) Radiator for low-pressure exhaust gas recirculation, h) Cylinder block, i) Thermostat, k) Radiator, l) Switchable coolant pump, m) Coolant valve for cylinder head N489, n) Engine oil cooler, o) Charge air cooler, p) Low-temperature radiator, q) Charge air cooling pump V188pe rm itte dun le534urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pun leAG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s sility ab y li an pt cerrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enr fo ng© VOLKSWAGEN AG, Wolfsburg All rights and rights to make technical alterations reserved. 000.2812.91.20 Technical status 07/2014 Volkswagen AG After Sales Qualification Service Training VSQ-2 Brieffach 1995 38436 Wolfsburg, Germany❀ This paper was manufactured from pulp that was bleached without the use of chlorine.ht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t. C op yi