TECHNICAL DOCUMENTATION

SSP 547 The 2,0-l 176-kW TDI Biturbo Engine

PDFEN44 pages15 MB
SSP 547 The 2,0-l 176-kW TDI Biturbo Engine - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingSelf-study Programme 547The 2.0-l 176-kW TDI Biturbo Engine from the EA288 Diesel Engine Family Design and functionAG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s sility ab y li an pt cees, in part or in w l purpos hole ercia , is n m ot compe rm itte dun lerrectness of i t to the co nform spec a t i h re o n in wit thi sr te o iva r rp fo g ndo c um enht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t. C op yi urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pThe 2.0-l TDI biturbo engine engine family and is being used for the first time in the Passat 2015. Its output of 176 kW makes it the most powerful four-cylinder diesel engine in the Volkswagen Passenger Cars range. The very high torque of 500 Nm is reached at an engine speed of 1,750 rpm. In order to transfer the power onto the road in the best way possible, the engine has been combined with 4MOTION all-wheel drive and a 7-speed dual clutch gearbox. Thanks to its modern engine management system and the SCR exhaust gas treatment system, the engine is very environmentally friendly and produces low CO2 emissions.ility ab y li an pt ceun leAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo th u ac a developed by Volkswagen is a member of the EA288 rdiesel s srrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enr fo ngs547_100The Self-study Programme shows the design and function of new developments. The contents will not be updated.For current testing, adjustment and repair instructions, refer to the relevant service literature.2ht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py iImportant note Contentsun leAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo th u ra a c s ses, in part or in w l purpos hole ercia , is n m ot compe rm itte dIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 The 2.0-l 176-kW TDI biturbo engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Engine mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Cylinder block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Crankshaft group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Cylinder head. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Camshaft housing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Toothed belt drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Oil supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Thermal management system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Air duct system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Turbocharger system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Charge pressure control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Emission control module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Trap catalytic converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Common rail fuel system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30r te o iva r rp fo g nility ab y li an pt cerrectness of i t to the co nform spec a t i h re o n in wit thi sdo c um enEngine management system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 System overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Engine control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Exhaust gas temperature sender 1 G235 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 Special tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Test your knowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39AG.ht rig py Co t.agen lksw Vo byProte cted by c o py rig ht . C op yi3 IntroductionThe 2.0-l 176-kW TDI biturbo engineThe 2.0-l 176-kW biturbo engine is based on the EA288 V modular diesel matrix introduced in 2012. AG. olkswagen AG d agen things by using oes turbochargers arranged in series. w s Its high power output has been achieved among other two k not olyV db ise r tho au s sgu ara nte eo ra ces, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nTechnical features - Two-stage turbocharger system consisting of high-pressure and low-pressure turbochargers - Two balance shafts - Thermal management system using an on-demand coolant pump - Water-cooled charge air cooler - Emission control module with an oxidising catalytic converter and a diesel particulate filter - Dual-circuit exhaust gas recirculation system consisting of high-pressure and low-pressure exhaust gas recirculation - SCR exhaust gas treatment system - Common rail fuel injection with a maximum injection pressure of 2,500 barility ab y li an pt cerrectness of i t to the co nform spec at i h re o n wit in t hisdo c um ens547_0704ht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t. C op yi Technical data Engine code Type Displacement Bore Stroke Valves per cylinder Compression ratio Firing order Maximum outputun leCUAA 4-cylinder in-line engine 1,968 cm3 81.0 mmAG. Volkswagen AG d agen oes ksw not l o 4 gu yV b ara d e nte is r o eo h 15.5:1 ut ra a c s s95.5 mmility ab y li an pt ce1-3-4-2urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d p176 kW at 4,000 rpm 500 Nm at 1,750 to 2,500 rpm Bosch EDC 17 Diesel compliant with DIN EN590 Dual-circuit exhaust gas recirculation system, oxidising catalytic converter, diesel particulate filter and SCR system EU6Maximum torquerrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enEngine management system FuelExhaust gas treatmentEmission standard Torque and power diagram[Nm] 520 500 480 460 440 420 400 380[kW]r fo ng180 170 160360 340902,0004,0006,000[rpm]s547_092ht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py i150 140 130 120 1101005 Engine mechanicses, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo th u ra a c s sility ab y li an pt ceCylinder blockThe cylinder block is based on the 2.0-l TDI engines from the EA288 diesel engine family (mono turbo). It is made from an alloy of cast iron with flake graphite. Adding the reinforcements to the cylinder block has increased the strength and improved the acoustics.rrectness of i t to the co nf o r m spec atio h re n in witthi sd o cu m enBalance shaftsht rig py Co t.Prote cted by c o py rig ht . C op yiThe bolts for the crankshaft bearing caps are longer due to the increased loads and are screwed deeper into the cylinder block.CrankshaftCrankshaft bearing capsBolt for crankshaft bearing cap6agen lksw Vo byReinforcementsAG.s547_003Grey cast iron cylinder blockCrankshaft bearing capss547_102 Conrod bearings Crankshaft groupCrankshaftes, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngThe 42, CrMoS4). It is mounted in five bearings and has four counterweights on the crank webs. The gears for driving the balance shafts and for driving the oil pump have been shrunk onto the crankshaft.ility ab y li an pt cen AG. Volkswagen AG do es n wage s k l ot g o yV ua b ran ed s i tee r o h t or ac au forgedsscrankshaft is made from a high-strength steel alloy (materialrrectness of i t to the co nf o r m spec atio h re n in witPistonsThe pistons are made of aluminium and feature a new piston geometry. The central piston bowl has been enlarged for the biturbo engine to reduce the compression ratio to 15.5:1 (110-kW mono turbo 16.2:1). The pistons have an annular cooling channel and are cooled via piston spray nozzles in the cylinder block.The piston spray nozzles have an enlarged oil flow that allows better cooling of the pistons. The annular cooling channel has been optimised and has been moved further up towards the piston crown. The piston crown and piston bowl are cooled better due to the higher position of the cooling channel.thi sd o cu m enAnnular cooling channelOil inlet/ outlet Oil inlet/ outlets547_103 Counterweight Balance shaft Crankshaft bearingGear wheel for driving the balance shaftsagen lksw Vo byPiston with central piston bowlAG.Prote cted byht rig py Co t.c o p yri gh t . C op yiFracture-split trapezoidal conrodBalance shafts547_1047 Engine mechanicsCylinder heades, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo th u ra a c s sThe cylinder head is made from an aluminium alloy and uses four-valve technology. The valves are actuated by roller rocker fingers with hydraulic compensation elements. The intake ports have been made straighter and have larger crosssections to minimise pressure losses and allow a high flow of charge air.The valve arrangement uses the traditional design, i.e. the inlet valves are on the intake side and the exhaust valves are on the exhaust side.rrectness of i t to the co nform spec at i h re o n wit in t hisility ab y li an pt ceRoller rocker fingerExhaust portht rig py Co t.do c um enCompensation elementagen lksw Vo byExhaust valve s547_115Inlet valveCross-flow cooling The cylinder head uses cross-flow cooling with a lower and an upper cooling jacket. The cooling of the cylinder head has been improved with coolant passages between the inlet ports.s547_071 Coolant passages between the inlet ports8AG.Prote cted by c o py rig ht . C op yiIntake portUpper coolant jacketLower coolant jacket Camshaft housingThe inlet and exhaust camshafts have been integrated into a camshaft housing. The exhaust camshaft is driven by a toothed belt. The exhaust camshaft then drives the inlet camshaft via spur gears. The sender wheel for the Hall sender G40 is located on the inlet camshaft. The Hall sender is inserted into the camshaft housing and bolted.Sender wheel for Hall sender G40 Hall sender G40 Inlet camshaftAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo th u ra a c s sility ab y li an pt cees, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g ns547_072Exhaust camshaftrrectness of i t to the co nform spec at i h re o n wit in t hisCamshaft housingSpur gearsdo c um enht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig ht . C op yi9 Engine mechanicsToothed belt driveThe exhaust camshaft, the two-piston high-pressure pump for the common rail system and the coolant pump are driven by the toothed belt drive. The toothed belt has been reinforced due to the increased loads.n AG. Volkswagen AG do es n wage s k l ot g o yV ua b ran ed s i tee r o h t or u ac a Exhaust camshaft Camshaft toothed ss belt pulleyility ab y li an pt ceurposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pun leInlet camshaftrrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enDamper wheelAutomatic tensioning roller Toothed beltDrive pulley for coolant pumpToothed belt pulley for high-pressure pumpDamper wheelr fo ngCrankshaft toothed belt pulleyDrive pulley for oil and vacuum pump on crankshaftMaintenance-free toothed belt for oil pumpOil and vacuum pump drive pulleyCrankshaft pulley The toothed belt is stretched four times per crankshaft revolution due to the use of a two-piston high-pressure pump. A bi-oval pulley has been fitted to the crankshaft to reduce the loading on the toothed belt. The bi-oval pulley changes the ratio and thus counteracts the stretching of the toothed belt.Small diameter10ht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t . C op yis547_105Large diameters547_113 Oil supplyThe oil is supplied via a two-stage, volume flow regulated vane pump. The oil pump is driven by the crankshaft via a maintenance-free toothed belt. It supplies the crankshaft group, the valve gear, the high-pressure turbocharger and the low-pressure turbocharger with sufficient engine oil.Oil pressure switch F1AG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte Oil pressure switch for reduced oil is r o eo th u pressure F378 ra a c s ses, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngility ab y li an pt ces547_011rrectness of i t to the co nf o r m spec atio h re n in witOil pressure control The oil pressure is controlled using two pressure stages. The switch-over from the low-pressure stage with a lower delivery rate of 2.0–2.3 bar to a high-pressure stage with a greater delivery rate of 3.3–3.8 bar occurs at an engine speed of 3,000 rpm.High-pressure stage 3.3-3.8 bar 2.0-2.3 bar Pressure requirementsLow-pressure stagethi sd o cu m en3,000 rpms547_042The oil pump switches to the higher oil pressure stage for the first 1,000 km in order to improve the running-in performance of the engine when it is new. After new parts are installed, e.g. engine, short engine, cylinder head, camshaft housing or turbocharger, the oil pressure control should be limited to the high oil pressure stage for 1,000 km. The high oil pressure stage is set with the vehicle diagnostic tester.AG.ht rig py Co t.agen lksw Vo byProte cted by c o py rig ht . C op yi11 Engine mechanicsThermal management systemThe coolant circuit consists of three sub-circuits: - Micro-circuit - High-temperature circuit - Low-temperature circuites, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngAG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s sility ab y li an pt cerrectness of i t to the co nf o r m spec atio h re n in witthi sd o cu m en12ht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t. C op yi Key1 Coolant expansion tank 2 Heat exchanger for heater 3 Exhaust gas recirculation cooler 4 Coolant pump for high-temperature circuit V467 5 Injector for reducing agent N474 6 Low-pressure turbocharger compressor housing 7 Low-pressure turbocharger bearing housing 8 Cylinder head 9 Gear oil cooler 10 Cylinder block 11 On-demand coolant pumpVolkswagen AG head .N489 12 Coolant valve for cylinder gen AG dk Vol sender G62 13 Coolant temperature byswaris 14 Charge airocooleredes, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nsensor G18 15 Temperature ss 16 Engine oil cooler 17 Thermostat 18 Throttle valve module GX3 19 Exhaust gas recirculation control motor GX5 20 Coolant pump for low-temperature circuit V468th auoes not gu ara nte eo ra cility ab y li an pt cerrectness of i t to the co nform spec at i h re o n wit in t his21 Actuator for engine temperature regulation N493 22 Water radiator for charge air cooling circuit 23 Radiator for engine coolant 24 Auxiliary radiator Restrictor Non-return valveThe system should be charged and bled with the cooling system charge unit VW6096 and the vehicle diagnostic tester together with „Guided Functions”. Always follow the instructions and observe the information provided in ELSA when working on the cooling system. You will find further information about the function of the coolant circuit in Selfstudy Programme no. 514 „The New EA288 Diesel Engine Family”.ht rig py Co t.do c um ens547_035agen lksw Vo byAG.Prote cted by c o py rig h t . Co py i13 Engine mechanicsMicro-circuitWhen the engine is cold, the micro-circuit enables the engine and the passenger compartment to be warmed up quickly. Coolant flows through the following components: - Heat exchanger for heater (2) AG. Volkswagen AG d - Exhaust gas recirculation cooler (3) agen oes ksw not l o V gu y b ara - Coolant pump for d nte ise r o eo h high-temperature circuit V467 (4) t u ra a c s s - Low-pressure turbocharger bearing housing (7) - Cylinder head (8) - Gear oil cooler (9) - Cylinder block (10) - On-demand coolant pump (11) - Coolant valve for cylinder head N489 (12) - Coolant temperature sender G62 (13)urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pun leility ab y li an pt cerrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um ens547_055High-temperature circuit14ht rig py Co t.agen lksw Vo byAG.Prote cted byThe thermostat opens once the coolant temperature reaches approximately 92°C. Coolant flows through the following components: - Coolant expansion tank (1) - Heat exchanger for heater (2) - Exhaust gas recirculation cooler (3) - Coolant pump for high-temperature circuit V467 (4) - Low-pressure turbocharger bearing housing (7) - Cylinder head (8) - Gear oil cooler (9) - Cylinder block (10) - On-demand coolant pump (11) - Coolant valve for cylinder head N489 (12) - Coolant temperature sender G62 (13) - Engine oil cooler (16) - Thermostat (17) - Throttle valve module GX3 (18) - Exhaust gas recirculation control motor GX5 (19) - Radiator (23) - Auxiliary radiator (24)c o p yri gh t. C op yir fo ngs547_056 Low-temperature circuitThe low-temperature circuit cools the intake air temperature to approximately 45°C in the charge air cooler. Coolant flows through the following components: - Injector for reducing agent N474 (5) - Compressor housing of low-pressure turbocharger (6) - Charge air cooler (14) - Temperature sensor G18 (15) - Coolant pump for low-temperature circuit V468 (20) - Actuator for engine temperature regulation N493 (21) - Water radiator for charge air cooling circuit (22)s547_057Temperature sensor G18urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pun len AG. Volkswagen AG do es n wage s k l ot g o yV ua b ran ed s i The temperature sensor G18 is screwed in directly in front of tee the rthe water-cooled charge air cooler. It measures o h t or u ac a input coolant temperature of the water-cooled charge air cooler. ssility ab y li an pt ceCharge air coolerrrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enSignal use The engine control unit uses the signal to calculate the required position of the actuator for engine temperature regulation N493.Temperature sensor G18agen lksw Vo byht rig py Co t.AG.Prote cted byc o p yri gh t . C op yiEffects upon failure If the signal fails, the actuator for engine temperature regulation N493 is set to cooling position, i.e. the coolant flows only via the water radiator for charge air cooling circuit.r fo ngs547_07415 Engine mechanicsActuator for engine temperature regulation N493urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pIn the EA288 TDI engines with a turbocharger, coolant temperature in the low-temperature circuit is regulated with the electrical coolant pump for lowtemperature circuit. In the 2.0-l TDI biturbo engine, the coolant temperature is regulated by the actuator for engine temperature regulation N493.un len AG. Volkswagen AG do es n wage s k l ot g o yV ua b ran ed s i tee r o h t or u a c s the Regulation with the actuator for engine a temperature sregulation has the following advantages: - The coolant temperature can be adjusted quickly and precisely. - The thermal loading of the charge air cooler is low due to the smaller temperature differences between the coolant and the charge air. - The electrical coolant pump in the low-temperature circuit is fully activated as far as possible and thus ensures a high coolant flow to the water-cooled charge air cooler. Heat is thus constantly dissipated from the charge air cooler and a build-up of heat is avoided.ility ab y li an pt cerrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enr fo ngConnection to bypass channel Adjustable passagec o p yri gh t . C op yiConnection to radiatorht rig py Co t.Charge air coolerBypass passageWater radiator for charge air cooling circuits547_096Actuator for engine temperature regulation N493Adjustment unit with evaluation electronicsFunction of actuator for engine temperature regulation N493 The actuator for engine temperature regulation N493 is adjusted according to the engine load and the coolant temperature in the low-temperature circuit. The amount of coolant bypassing the radiator increases as the adjustable passage is moved towards the bypass passage. The coolant that bypasses the radiator is not cooled.The adjustable passage is continuously variable and is controlled by the evaluation electronics in the adjustment unit. The adjustment unit is integrated into the actuator for engine temperature regulation N493. The evaluation electronics determine the position of the passage by means of a travel indicator in the adjustment unit and transmit it to the engine control unit.16AG.Temperature sensor G18Coolant pump for low-temperature circuit V468agen lksw Vo byProte cted byInlet connections547_106 es, in part or in w l purpos hole ercia , is n m ot comAir duct systempe rm itte dun leAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo th u ra a c s sThe charge air system has been designed so that the distances are short and the cross-sections large. This minimises pressure losses. Thanks to the compact charge air system, a small volume needs to be compressed and there is a very fast build-up of charge air pressure.One particular load is the high charge pressure of up to 3.8 bar (absolute) as well as the thermal loading that acts on the components in the charge air system. Hoses have therefore been avoided as far as possible and charge pressure pipes that can withstand higher temperatures and pressures are used.ility ab y li an pt cerrectness of i t to the co nform spec a t i h re o n in wit thi sturbocharger Inlet valve Intake air Intake manifold Water-cooled charge air coolerThrottle valve moduleCompressor bypass valve (closed) s547_077 High-pressure turbochargerPulsation damperht rig py Co t.agen lksw Vo byAG.The charge air system is made up of the following components: - Air filter - Low-pressure turbocharger - High-pressure turbocharger - Charge pressure pipes - Pulsation damper - Compressor bypass valve - Throttle valve module - Intake manifold with integrated charge air cooler - Flow-optimised intake ports in the cylinder head - Inlet valves Low-pressurer te o iva r rp fo g ndo c um enProte cted by c o py rig ht . C op yi17 Engine mechanicsIn the 2.0-l TDI biturbo engine, two turbochargers connected in series produce the charge pressure. At low engine speeds, the intake air is pre-compressed by the low-pressure turbocharger and the main n AG. Volkswagen AG do es n wage s k l ot g o compression is performed by the high-pressure turbocharger (two-stage operation). At high engine speeds, the yV ua b d e nteown (single-stage operation). low-pressure o turbocharger compresses the intake air onra its risun leth au sseo ra cility ab y li an pt cees, in part or in w l purpos hole ercia , is n m ot compe rm itte drrectness of i t to the co nform spec a t i h re o n in wit thi sr te o iva r rp fo g ndo c um en2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23Air mass meter G70Compressor wheel in low-pressure turbocharger Charge pressure sender 2 G447Compressor wheel in high-pressure turbocharger Compressor bypass valve Throttle valve module GX3 Charge pressure sender G31 Intake air temperature sender G42 Charge air cooler Charge air temperature sender after charge air cooler G811 Exhaust gas recirculation control motor GX5 Exhaust gas temperature sender 1 G235 Turbine bypass flap Vacuum unit with position sender for charge pressure positioner G581 Turbine changeover valve N529 Turbine in high-pressure turbocharger Turbocharger 1 control unit J724 Bypass flap Vacuum unit for bypass flap Charge pressure control solenoid valve N75 Turbine in low-pressure turbocharger Lambda probe 1 before catalytic converter GX10 24 25 26 27 28 29 30 31 32 33 34 35 36 NOx sender G295 Exhaust gas temperature sender 2 G448 Oxidising catalytic converter Exhaust gas temperature sender 3 G495 Injector for reducing agent N474 Pressure differential sender G505 Diesel particulate filter Exhaust gas recirculation cooler Exhaust gas recirculation control motor GX6 Exhaust gas temperature sender 4 G648 Pressure sender 2 for exhaust gas recirculation G692 Trap catalytic converter Exhaust flap control unit J883 s547_07618agen lksw Vo by1Air filterAG.Prote cted by c o py rig ht . C op yiKeyht rig py Co t. The newly developed turbocharger system quickly builds up charge air pressure even at low engine speeds, responds quickly and achieves a high engine torque.es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nTurbocharger systemn AG. Volkswagen AG do es n wage s k l ot g o yV ua b ran ed s i tee r o h t or u ac a ssA high specific engine output is reached at high engine speeds due to the high charge pressure of up to 3.8 bar (absolute).Special features of the turbocharger system: - High-pressure turbocharger with small turbine, small compressor wheel and electrically adjusted vanes. This achieves quick response at low engine speeds. - Low-pressure turbocharger with large turbine and large compressor wheel. As a result, a high charge pressure is reached at high engine speeds. A high power output is thus reached at high engine speeds. - Compact design: the high- and low-pressure turbochargers are mounted directly on the exhaust manifold. - If repairs are necessary, the turbochargers, charge pressure positioners and the turbocharger 1 control unit J724 can be replaced individually.do c um enht rig py Co t.ility ab y li an pt cerrectness of i t to the co nform spec at i h re o n wit in t hisCompressor wheel Vacuum unit with position sender for charge pressure positioner G581Low-pressure turbocharger TurbineVacuum unit for bypass flapTurbocharger 1 control unit J724 Turbine Adjustable vanesThe designation of the high-pressure turbocharger and of the low-pressure turbocharger has been assigned on the basis of the two-stage operation in which the low-pressure turbocharger is used exclusively for pre-compression (low pressure) of the intake air and the high-pressure turbocharger takes care of the main compression (high pressure).agen lksw Vo byAG.Prote cted byc o p yri gh t . C op yiHigh-pressure turbocharger Exhaust manifolds547_10119 Engine mechanicsLow-pressure turbochargeres, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngThe low-pressure turbocharger is located above the high-pressure turbocharger and is arranged after the high-pressure turbocharger in the exhaust gas flow direction.AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s sCompared with the high-pressure turbocharger, the turbine and the compressor wheel are larger than in the low-pressure turbocharger. As a result, the intake air is compressed more and a maximum charge pressure of 3.8 bar (absolute) is attained at high engine speeds or with high exhaust gas mass flows. The turbine reaches speeds up to 165,000 rpm.Water-cooled compressor housing The intake air temperature can rise to approx. 230°C at full load. Coolant flows through the compressor housing of the low-pressure turbocharger to cool it. The compressor housing is incorporated into the low-temperature circuit. Cooling the compressor housing prevents the compressor wheel getting too hot and thus protects the components.ility ab y li an pt cerrectness of i t to the co nf o r m spec atio h re n in witthi sd o cu m enCoolant supply and returnVacuum unit with position sender for charge pressure positioner G58120AG.Prote cted byCooling jacket in compressor housingVacuum unit for bypass flapht rig py Co t.agen lksw Vo byc o p yri gh t. C op yiCompressor housings547_097 es, in part or in w l purpos hole ercia , is n m ot comWater-cooled bearing housing The loading of the turbocharger has increased because the exhaust gas temperature has also risen with the increasing power outputs of the new engines. Therefore, in addition to cooling the oil for the sleeve bearings and the water-cooled compressor housing, coolant also flows through the bearing housing. The water-cooled bearing housing thus reduces the transfer of heat to the engine oil.pe rm itte dun leAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo th u ra a c s sFurthermore the electric coolant pump for high-temperature circuit V476 is activated for up to 15 minutes after the engine is switched off. The continued coolant circulation dissipates the heat from the low-pressure turbocharger. As a result, "coking" of the engine oil and damage to the sleeve bearings is prevented. The water-cooled bearing housing has been incorporated into the micro-temperature circuit.rrectness of i t to the co nform spec a t i h re o n in wit thi sility ab y li an pt cer te o iva r rp fo g ndo c um enCompressor housing of lowpressure turbochargerWater-cooled bearing housingagen lksw Vo byCoolant supply and returnEngine oil return from lowpressure turbocharger to cylinder blockht rig py Co t.AG.Prote cted by c o py rig ht . C op yiTurbine housing of low-pressure turbochargers547_10921 Engine mechanicsHigh-pressure turbochargerThe high-pressure turbocharger is bolted directly to the exhaust manifold and is located below the lowpressure turbocharger. At low engine speeds, i.e in two-stage operation, charge pressure is built up by the high-pressure turbocharger. In the high-pressure turbocharger, the diameters of the turbine and the compressor wheel are smaller than those in the low-pressure turbocharger. Charge air pressure is built up more quickly at low engine speeds due to the smaller turbine and compressor wheel along with the electrical vane adjustment. This enables fast response and high torque at low engine speeds. The high-pressure turbocharger reaches speeds of up to 240,000 rpm. The sleeve bearings are lubricated and cooled with engine oil. The vanes are adjusted by the electrical turbocharger 1 control unit J724. Electrical adjustment of the vanes is more precise and faster than pneumatic adjustment.es, in part or in w l purpos hole ercia , is n m ot compe rm itte dun leAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo th u ra a c s sCompressor housingTurbocharger 1 control unit J724ility ab y li an pt cerrectness of i t to the co nform spec a t i h re o n in wit thi sCompressor inletCompressor outletTurbine housingExhaust manifoldr te o iva r rp fo g ndo c um enYou will find further information about the design and function of the turbocharger in Self-study Programme no. 190 „Adjustable Turbocharger”.22AG.Engine oil return from bearing housing to crankcases547_107ht rig py Co t.agen lksw Vo byProte cted by c o py rig ht . C op yi Turbine bypass flapagen The turbine bypass flap regulates between two-stage ksw Vol y b and single-stage operation. ed ris o h The turbine bypass flap is installed in the ut sa low-pressure turbocharger. The further the turbine s bypass flap is opened, the greater the exhaust gas mass flow that is directed to the turbine in the low-pressure turbocharger. The turbine bypass flap is adjusted via the turbine changeover valve N529 and the vacuum unit with position sender for charge pressure positioner G581. Turbine bypass It is adjusted pneumatically by the vacuum system. flap The flap is open in unpressurised state.es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngAG. Volkswagen AG d oes not gu ara nte eo ra cility ab y li an pt cerrectness of i t to the co nf o r m spec atio h re n in wits547_081thi sd o cu m enThe bypass flap is located in the low-pressure turbocharger. It is used in single-stage operation for charge pressure control of the low-pressure turbocharger. When the bypass flap is open, part of the exhaust gas mass does not flow to the turbine in the low-pressure turbocharger, but is instead directed downstream of the turbine via a bypass duct. At an outside temperature of 20°C and at sea level, the bypass flap is approximately 50% open: this provides a charge pressure reserve in case the outside temperature rises and the altitude increases. The bypass flap is actuated by the charge pressure control solenoid valve N75 and the vacuum unit for bypass flap adjustment. It is adjusted pneumatically by the vacuum system. The bypass flap is open when no pressure is applied.Vacuum unit for bypass flapVacuum unit with position sender for charge pressure positioner G581AG.Prote cted byBypass flapBypass flapht rig py Co t.agen lksw Vo byc o p yri gh t. C op yis547_08223 Engine mechanicsA agen Compressor bypass valve ksw VolG. Volkswagen AG d oes not gu ara nt In single-stageee operation , or acof the low-pressure turbocharger. In two-stage operation, the charge pressure is mainly produced in the high-pressure turbocharger. As a result, the charge pressure in front of the compressor bypass valve is lower than the charge pressure behind the compressor bypass valve. This means that, in twostage operation, the higher charge pressure behind the compressor bypass valve holds the compressor bypass valve closed. This prevents the air that is compressed by the high-pressure turbocharger being drawn in again by the high-pressure turbocharger.es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngy db ise r The compressor bypass valve is installed in the tho au s s charge air system in a bypass passage downstreamthe high charge pressure of the low-pressure turbocharger opens the compressor bypass valve and the charge air can flow via the bypass passage directly towards the charge air cooler. Without the bypass passage, the air would have to flow via the compressor wheel in the highpressure turbocharger, which would then act as a restrictor.ility ab y li an pt cerrectness of i t to the co nf o r m spec atio h re n in witthi sd o cu m ens547_110 Compressor bypass valve (open)Compressor bypass valve24ht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py iLow-pressure turbochargers547_111High-pressure turbocharger Exhaust manifoldThe exhaust manifold has the task of collecting the exhaust gas mass flow from the cylinders and feeding it via passages to the high-pressure and low-pressure turbochargers. When the turbine bypass flap is closed, the whole exhaust gas mass flow is guided to the high-pressure turbocharger and then drives the turbine. From there, the exhaust gas mass flow is guided back to a passage in the exhaust manifold and onward to the low-pressure turbocharger. The remaining energy of the exhaust gas mass flow is thus sent to the turbine in the low-pressure turbocharger and drives it. When the turbine bypass flap is open, the exhaust gas mass flow is fed via a passage directly to the turbine in the low-pressure turbocharger. The further the turbine bypass flap is opened, the greater the exhaust gas mass flow that is guided to the turbine in the low-pressure turbocharger. This accelerates the turbine quicker and the charge pressure increases.Exhaust gas flows into the low-pressure turbocharger Turbine bypass flap (closed) Bypass passage leads to low-pressure turbocharger Exhaust gas from high-pressure AG. Volkswagen AG d turbocharger to low-pressure turbocharger agen ow olks yV b ed ris ho t auLow-pressure turbochargerHigh-pressure turbocharger Connection to high-pressure exhaust gas recirculationpe rm itte dExhaust manifoldun lesses n ot g ua ran tee or acility ab y li an pt ces547_112Exhaust gas flows into the high-pressure turbochargerrrectness of i t to the co nform spec a t i h re o n in wit thi sCharge pressure controlThe charge pressure is controlled according to the load and the engine speed: - 1 Control range: two-stage operation The charge pressure is controlled by adjusting the vanes in the high-pressure turbocharger. - 2 Control range: two-stage operation The charge pressure is controlled by adjusting the turbine bypass flap. - 3 Control range: single-stage operation The low-pressure turbocharger compresses the intake air on its own. The charge pressure is controlled via the bypass flap.r te o iva r rp fo g nes, in part or in w l purpos hole ercia , is n m ot coms547_084Torque and engine speed diagramdo c um enht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py i25 Engine mechanics1 Control rangeTwo-stage operation The charge pressure is controlled by adjusting the vanes in the high-pressure turbocharger.Torque and engine speed diagramHigh-pressure turbochargerTurbine bypass flap Vacuum unit with position sender for charge pressure positioner G581Vanes Bypass flap Compressor bypass valveAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s sVacuum unit for bypass flapes, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nTurbocharger 1 control unit J724ility ab y li an pt ces547_050Low-pressure turbochargerrrectness of i t to the co nform spec at i h re o n wit in t hisAir duct system The intake air is pre-compressed by the compressor in the low-pressure turbocharger and is then guided to the compressor in the high-pressure turbocharger. The pre-compressed air enters the main compression stage in the high-pressure turbocharger. The compressor bypass valve is closed.Exhaust gas duct system The exhaust gas mass flow is guided to the turbine in the high-pressure turbocharger, and onward from there to the turbine in the low-pressure turbocharger. The turbine speed in the high-pressure turbocharger is controlled with the adjustable vanes (according to the torque). The turbine bypass flap and the bypass flap are closed.do c um en26ht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py i 2 Control rangeTwo-stage operation The charge pressure is controlled via the turbine bypass flap.Torque and engine speed diagramHigh-pressure turbochargerTurbine bypass flap Vacuum unit with position sender for charge pressure AG. Volkswagen AG d agen oes positioner G581 w s k n ot Vol Vanesgu ara nte eo ra cCompressor bypass valvees, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g ny db ise r tho au s sBypass flapVacuum unit for bypass flapility ab y li an pt cerrectness of i t to the co nform spec at i h re o n wit in t hisTurbocharger 1 control unit J724s547_051Low-pressure turbochargerht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t. C op yiAir duct system The intake air is pre-compressed to a greater extent by the low-pressure turbocharger. The pre-compressed intake air is then guided to the high-pressure turbocharger where it enters the main compression stage. The compressor bypass valve is closed.Exhaust gas duct system At mid-range engine speeds, the turbine bypass flap is adjusted according to the torque. The further the turbine bypass flap is opened, the greater the exhaust gas mass flow that is guided directly from the exhaust manifold to the turbine in the low-pressure turbocharger. The turbine in the highpressure turbocharger continues to be driven by the remaining exhaust gas mass flow. The vanes in the high-pressure turbocharger are set at a steep angle and the bypass flap remains closed.do c um en27 Engine mechanics3 Control rangeSingle-stage operation The charge pressure is controlled by the bypass flap in the low-pressure turbocharger.Torque and engine speed diagramurposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pHigh-pressure turbochargerun leAG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s sility ab y li an pt ceTurbine bypass flapVacuum unit with position sender for charge pressure positioner G581rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enVanes Bypass flapCompressor bypass valveVacuum unit for bypass flapr fo ngTurbocharger 1 control unit J724s547_052agen lksw Vo byAG.Prote cted byLow-pressure turbochargerAir duct system The intake air is compressed only by the compressor in the low-pressure turbocharger. All of the compressed intake air passes through the open compressor bypass valve and follows a separate charge air route that bypasses the compressor wheel in the high-pressure turbocharger. The intake air is compressed exclusively by the lowpressure turbocharger.Exhaust gas duct system The major part of the exhaust gas mass (approximately 70%) flows through the fully open turbine bypass flap past the turbine in the highpressure turbocharger. The vanes in the high-pressure turbocharger are set at a steep angle. The high exhaust gas mass flow goes directly to the turbine in the low-pressure turbocharger and drives it. The turbine speed in the low-pressure turbocharger is controlled with the bypass flap.28ht rig py Co t.c o p yri gh t. C op yi Emission control moduleInjector for reducing The emission control module is bolted directly to the agent N474 low-pressure turbocharger. Upper bracket with Since it is located close to the engine, the emission elongated holes control module reaches its operating temperature after a short start up time. The diesel particulate filter has a copper-zeolite coatOxidising cataing and thus also works as a reduction catalytic conlytic converter verter for the SCR system. The emission control module is bolted to the engine using four brackets. The upper bracket has elongated AG. Volkswagen AG d holes to allow for component tolerances. The elonagen oes ksw not l o gu yV gated holes enable the emission control module to be b ara d e nte is r eo positioned and secured without any tension. thoes, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngau ssra cility ab y li an pt ceDiesel particulate filter/ SCR catalytic converterLower bracketTrap catalytic converterThe trap catalytic converter is located behind the diesel particulate filter and is bolted to the emission control module. It has the task of oxidising the carbon monoxide produced during the regeneration of the diesel particulate filter into carbon dioxide. Furthermore it prevents ammonia being released into the outside air.Exhaust flap control unit J883Trap catalytic converterEmission control module s547_086You will find further information about the design and function of the SCR system in Self-study Programme no. 540 „The Selective Catalytic Reduction Exhaust Gas Treatment System in the Passat 2015”.s547_085rrectness of i t to the co nf o r m spec atio h re n in witthi sd o cu m enht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py i29 Engine mechanicsCommon rail fuel systemThe 2.0-l TDI biturbo engine uses a common rail fuel system with piezo injectors and a two-piston highpressure pump. The common rail fuel system from Bosch produces a maximum injection pressure of 2,500 bar. The high fuel pressure is generated by a two-piston highpressure pump. The piezo injectors each have ten injection holes and allow a good, precise and fast injection delivery at maximum injection pressure. Maximum injections in normal operation: - two pilot injections, one main injection and one post-injection Maximum injections in regeneration operation: - two pilot injections, one main injection and up to five post-injectionsInjectors N30 - N33 Fuel pressure regulating valve N276AG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s ses, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nHigh-pressure accumulator (rail)ility ab y li an pt cerrectness of i t to the co nform spec at i h re o n wit in t hisFuel pressure sender G247s547_022Fuel metering valve N290do c um enTwo-piston high-pressure pumpagen lksw Vo byYou will find further information about the design and function of the high-pressure pump in Self-study Programme no. 495 „The 3.0 l V6 TDI Engine (Generation 2)”.30ht rig py Co t.AG.Prote cted by c o py rig h t . Co py i Overview of fuel systemurposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pun leAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo th u ra a c s sility ab y li an pt cerrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enr fo ngs547_034KeyHigh fuel pressures up to 2,500 bar Fuel supply pressure and fuel return pressure from the injectors 4.0–6.0 barFuel return pressure 0–1 bar Fuel return pressure from the injectors 11.0–17.0 bar1 2 3 4 5 6Fuel pump control unit J538 Fuel system pressurisation pump G6 Fuel filter Fuel temperature sender G81 High-pressure pump Fuel metering valve N2907 8 9 10 11 12Fuel pressure regulating valve N276 High-pressure accumulator (rail) Fuel pressure sender G247 Injectors N30, N31, N32, N33 Pressure retention valve Pulsation damperht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig ht . C op yi31 Engine management systemSystem overviewSensors Temperature sensor G18 Engine speed sender G28 Hall sender G40 Exhaust emissions warning lamp K83 AG. Volkswagen AG d agen oes ksw not l o gu yV ara db nte ise r o eo h ut r a Diesel particulate filter a c s sility ab y li an pt ceGlow period warning lamp K29Air mass meter G70 Coolant temperature sender G62urposes, in part or in wh ole, cial p is n mer m ot p o c erm or e t a itte v i r d pIntake air temperature sender G42Charge air temperature sender after charge air cooler G811 Charge pressure sender G31 Charge pressure sender 2 G447 Fuel temperature sender G81 Fuel pressure sender G247 Exhaust gas recirculation valve 1 GX5 Exhaust gas recirculation valve 2 GX6 NOx sender G295 Lambda probe 1 before catalytic converter GX10 Exhaust gas temperature senders 1–4 G235, G448, G495, G648 Pressure differential sender G505 Pressure sender 2 for exhaust gas recirculation G692 Turbocharger 1 control unit J724un lewarning lamp K231r fo ngData bus diagnostic interface J533ht rig py Co t.rrectne s s o f i t to the co n form spec atio h re n wit i n thi sd o c um enControl unit in dash panel insert J285Convenience CAN busThrottle valve module GX3Vacuum unit with position sender for charge pressure positioner G581 Oil pressure switch for reduced oil pressure F378 Exhaust flap control unit J883 Oil level and oil temperature sender G266 Oil pressure switch F132agen lksw Vo byAG.Prote cted by c o py rig h t . Co py iPowertrain CAN busCylinder 3 combustion chamber pressure sender G679 Accelerator pedal module GX2 Brake light switch FClutch position sender G476 Actuators Fuel pump control unit J538 Fuel delivery unit GX1 Injectors, cylinders 1–4 N30, N31, N32, N33 Fuel metering valve N290 Fuel pressure regulating valve N276AG. Volkswagen AG d agen oes ksw not l o VCharge pressure control solenoid valve N75es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nby ed ris o th au ssgu N474 Injector for reducing agent arante eo ra cility ab y li an pt ceTurbine changeover valve N529Throttle valve module GX3rrectness of i t to the co nform spec at i h re o n wit in t hisExhaust gas recirculation valve 1 GX5 Exhaust gas recirculation valve 2 GX6 Exhaust flap control unit J883Coolant pump for low-temperature circuit V468Coolant pump for high-temperature circuit V467 Coolant valve for cylinder head N489 Valve for oil pressure control N428 Turbocharger 1 control unit J724AG.ht rig py Co t.do c um enDiagnostic connectorLambda probe 1 before catalytic converter GX10 Engine control unit J623 Heater element for crankcase breather N79 Actuator for engine temperature regulation N493 Automatic glow period control unit J179 Glow plugs 1–4 Q10, Q11, Q12, Q13s537_049agen lksw Vo byProte cted by c o py rig ht . C op yi33 Engine management systemEngine control unitThe engine is controlled by the engine control unit with the designation EDC 17 (Electronic Diesel Control). The engine control unit is made by Bosch and has 196 pins due to the large number of sensorsAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is and actuators (connector A 91 pins and connector r o eo h ut ra a c s 105 pins). It is located on the left of the engine sBility ab y li an pt cees, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g ncompartment between the air filter housing and the fuse holder.rrectness of i t to the co nform spec at i h re o n wit in t hisdo c um enConnector BConnector AThe testing box VAS 6606 is used for testing the engine control unit J623.Engine control unit J623 s547_08734ht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py is547_068 Exhaust gas temperature sender 1 G235 AG. Volkswagen AG d gen oes swaes, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngThe 2.0-l 176-kW TDI generation of exhaust because the exhaust gas temperature can exceed 800°C. The new exhaust gas temperature sender 1 is screwed into the exhaust manifold and consists of ak Vol by d e uses a new biturbo engine ris tho u gas temperature senders a ssnot gu ara thermal element and n tee evaluation electronics. or The evaluation electronics and the thermal element acility ab y li an pt ceare separate from each other. This measure protects the evaluation electronics components against excessively high temperatures.rrectness of i t to the co nf o r m spec atio h re n in witEvaluation electronicsthi sd o cu m enThermal elementht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t . C op yis547_09835 Engine management systemDesign and function of exhaust gas temperature sender 1The voltage that is generated lies in the millivolt The exhaust gas temperature sender 1, which is fitted range. This effect is referred to in physics as the into the exhaust manifold, measures the exhaust gas Seebeck effect. The voltage generated is transmitted temperature in front of the high-pressure turbovia the nickel and nickel chromium wires to the charger turbine. evaluation electronics. The evaluation electronics If the exhaust gas temperature in front of the turbine evaluate the voltage and send the temperature to the rises above 830°C, the engine output will be reduced. AG. Volkswagen AG d agen oes w s k no engine control unit in the form of a SENT signal The exhaust gas temperature sender 1 ol thus protects t gu V y b ara d nteEdge Nibble Transmission). The (SENT= Single the turbocharger components.orise eo th ra exhaust gas temperature sensor has three wires It consists of a thermal element au and evaluation c s s because the evaluation electronics require a voltage electronics. The thermal element is made up of two supply. different metals that are connected to one another (nickel and nickel chromium).ility ab y li an pt cees, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngIn an electrical circuit composed of two different electrical conductor materials, an electrical voltage is generated when there is a temperature difference between the contact point (metal A and B) and the conductor ends (evaluation electronics).Effects of failure If the exhaust gas temperature sender 1 fails, there is no diesel particulate filter regeneration.rrectness of i t to the co nf o r m spec atio h re n in witEvaluation electronicsHigh-pressure turbocharger turbine housinght rig py Co t.thi sd o cu m ens547_094Thermal element Voltage difference between metals A and B Metal A36agen lksw Vo byAG.Prote cted byc o p yri gh t. C op yiConfiguration of exhaust gas temperature sender 1 G235 Sensor signal Evaluation electronicsTemperature difference due to spatial separationThermal elementMetal B s547_090 Structure of SENT protocol for exhaust gas temperature sender 1 G235Signal pattern of exhaust gas temperature sender 1 G235un leAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s ss547_091ility ab y li an pt cepe rm itte dSynchronisation Status Signal 1Signal 2 Check sum Pausees, in part or in w l purpos hole ercia , is n m ot comrrectness of i t to the co nform spec a t i h re o n in wit thi sSynchronisation The synchronisation sequence communicates information about the component sending the protocol. The data from the sender are transmitted, along with any error that is present.Signal 2 The current temperature is sent with the signal 2 sequence for exhaust gas temperature sender 1. Pressures, position feedback or also extended diagnosis data can be transferred in the signal 2 sequence of the SENT protocol.Signal 1 If an entry is made in the event memory, extended diagnosis data is transferred with the signal 1 sequence for exhaust gas temperature sender 1. Temperatures, pressures and position feedback can also be sent in the signal 1 sequence of the SENT protocol.Pause The pause separates the data messages from each other. The pause is optional in a SENT protocol.ht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py iStatus The status sequence informs the control unit that data is being transmitted.r te o iva r rp fo g nCheck sum In the checksum sequence, the transmitted data is checked for plausibility. If the value does not match, the transmitted data will be discarded by the control unit.do c um en37 ServiceSpecial toolsDescription T10497/4 Clamp Tool Usage for removing and installing the engineVAS 6606 Test box, 198-pinfor engine control unit diagnosticsVAS 6931 Engine and gearbox jackes, in part or in w l purpos hole ercia , is n m ot compe rm itte dun lefor removing and installing the engine n AG. Volkswagen AG do es n wage s k l ot g o V ua by ran ed s i tee r o h t or u ac a ssility ab y li an pt cerrectness of i t to the co nform spec a t i h re o n in wit thi sr te o iva r rp fo g ndo c um en38ht rig py Co t.agen lksw Vo byAG.Prote cted byc o p yri gh t . C op yi Which answers are correct? One or several of the given answers may be correct. 1.es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngAG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s sTest your knowledgeility ab y li an pt cerrectness of i t to the co nf o r m spec atio h re n in witWhich turbocharger is responsible for the main compression in two-stage operation? a) The low-pressure turbocharger. b) The high-pressure turbocharger.❒ ❒ ❒c) No intake air is compressed in two-stage operation.thi sd o cu m en2.What is the task of the turbine bypass flap?a) The turbine bypass flap has the task of rapidly reducing the charge pressure. b) The turbine bypass flap has the task of distributing the exhaust gas mass flow to the turbines in the high- and low-pressure turbochargers. c) The turbine bypass flap has the task of guiding the intake air to the compressor wheel in the low-pressure turbocharger.AG.❒❒3.What is the task of the bypass flap? a) The bypass flap has the task of regulating the charge pressure produced by the low-pressure turbocharger and protecting it against overspeed. b) The bypass flap has the task of regulating the single- or two-stage operation of the turbocharger system. c) The turbine bypass flap has the task of protecting the high-pressure exhaust turbocharger against overspeed.❒❒❒4.When is the compressor bypass valve open? a) At high engine speeds when the intake air is compressed only by the low-pressure turbocharger. b) At mid-range engine speeds when the main compression is performed by the high-pressure turbocharger. c) At low engine speeds when the main compression is performed by the high-pressure turbocharger.❒❒ ❒ht rig py Co t.agen lksw Vo byProte cted by c o py rig h t . Co py i❒39 Test your knowledge5.How is the temperature measured by the exhaust gas temperature sender 1 G235? a) With an NTC resistor. b) With a PTC resistor. c) With an AG. Volkswagen AG do es n wage s k l ot g o yV ua b ran ed s i tee r element. thermal o h t or u ac a ss❒ ❒ ❒ility ab y li an pt ce6.es, in part or in w l purpos hole ercia , is n m m ot p o c erm or e t a itte iv r du rp o nl f e ngIn which coolant circuit is the actuator for engine temperature regulation N493 installed?rrectness of i t to the co nf o r m spec atio h re n in wit❒ ❒ ❒a) In the low-temperature circuit. b) In the micro-circuit. c) In the high-temperature circuit.7.What is the task of the actuator for engine temperature regulation N493?thi sd o cu m en❒a) The actuator for engine temperature regulation N493 is only required for filling coolant so that the air is mixed sufficiently in the coolant circuit. b) The actuator for engine temperature regulation N493 mixes the coolant from the micro-circuit with the coolant from the high-temperature circuit. c) Quick and precise regulation of the coolant temperature in the low-temperature circuit.agen lksw Vo byAG.Prote cted by❒❒40Answers: 1. b); 2. b); 3. a); 4. a); 5. c); 6. a); 7. c)ht rig py Co t.c o p yri gh t . C op yi AG. Volkswagen AG d agen oes ksw not l o V gu y b ara d nte ise r o eo h t u ra a c s sility ab y li an pt cerrectness of i t to the co nform spec at i h re o n wit in t hisdo c um enht rig py Co t.41agen lksw Vo byAG.Prote cted byc o p yri gh t. C op yies, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n AG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo th u ra a c s sility ab y li an pt cerrectness of i t to the co nform spec a t i h re o n in wit thi sdo c um enht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig ht . C op yir te o iva r rp fo g n42es, in part or in w l purpos hole ercia , is n m ot compe rm itte dun le AG. Volkswagen AG d agen oes ksw not l o gu yV b ara d e nte is r o eo h ut ra a c s sility ab y li an pt cerrectness of i t to the co nform spec at i h re o n wit in t hisdo c um en43ht rig py Co t.agen lksw Vo byAG.Prote cted by c o py rig h t . Co py ies, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g n 547es, in part or in w l purpos hole ercia , is n m ot p om c r erm o e t a itte riv du p or nl f e g nn AG. Volkswagen AG do es n wage s k l ot g o yV ua b ran ed s i tee r o h t or u ac a ssility ab y li an pt cerrectness of i t to the co nform spec at i h re o n wit in t hisdo c um enVolkswagen AG After Sales Qualification Service Training VSQ-2 Brieffach 1995 D-38436 Wolfsburg❀ This paper was manufactured from pulp that was bleached without the use of chlorine.AG.Prote cted by© VOLKSWAGEN AG, Wolfsburg All rights reserved. Subject to technical modifications. 000.2813.04.20 Technical status 04/2015ht rig py Co t.agen lksw Vo byc o p yri gh t . C op yi