TECHNICAL DOCUMENTATION

SSP 610 Audi A3 2013 Onboard Power Supply and Networking

PDFEN44 pages3 MB
SSP 610 Audi A3 2013 Onboard Power Supply and Networking - PDF cover

This PDF is currently unavailable.

Read document text
Self Study Programme 610 For internal use onlyAudi A3 ’13 Onboard Power Supply and NetworkingAudi Service Training Whether the engine fuel system, the dual clutch gearbox, the infotainment system or any one of a number of driver assistance systems – a modern vehicle would cease to function without electrical and electronic equipment. A high-performance alternator, a battery rated for the vehicle's specification, and reliable and fast data transfer across various data bus systems are all vital components of a stable and efficient onboard power supply system.The first part of this self study programme summarises the onboard power supply of the Audi A3 ’13 and provides information on the functions, installation locations and specific features of numerous control units. The design and function of the various headlight and tail light versions are described in "Exterior lighting". This is a quick and direct way to obtain an in-depth knowledge of the electrical and electronic equipment in the Audi A3 ’13.610_070Learning objectives of this Self Study Programme: After you have worked your way through this Self Study Programme, you will be able to answer the following questions: • Where are the fuseholders located in the Audi A3 ’13 and what are their designations? • Where are electrical components fitted in the vehicle? • Which bus systems are used in the Audi A3 ’13? • What are the tasks of the control units in the vehicle? • What are the versions of the exterior lighting and how are the individual light functions implemented? • What are the versions of the headlight range adjustment system?2 ContentsPower supplyBattery _______________________________________________________________________________________________________________________________________________________ 4 Battery housing _____________________________________________________________________________________________________________________________________________ 4 Fuses, relays and jump start terminal ____________________________________________________________________________________________________________________ 5NetworkingInstallation locations of control units ____________________________________________________________________________________________________________________ 6 Topology _____________________________________________________________________________________________________________________________________________________ 8 Overview of bus systems __________________________________________________________________________________________________________________________________ 10 New features of the bus system __________________________________________________________________________________________________________________________ 10 Optical data bus system MOST150 _______________________________________________________________________________________________________________________ 11 Optical replacement control unit VAS 6778 _____________________________________________________________________________________________________________ 11Control unitsBrief descriptions __________________________________________________________________________________________________________________________________________ 12Exterior lightingLight switch _________________________________________________________________________________________________________________________________________________ 29 Headlights __________________________________________________________________________________________________________________________________________________ 30 Fog light ____________________________________________________________________________________________________________________________________________________ 35 Headlight range control ___________________________________________________________________________________________________________________________________ 37 Tail lights ____________________________________________________________________________________________________________________________________________________ 40 High-level brake light ______________________________________________________________________________________________________________________________________ 42 Number plate lights _______________________________________________________________________________________________________________________________________ 42AnnexSelf Study Programmes ___________________________________________________________________________________________________________________________________ 43• The Self Study Programme teaches a basic knowledge of the design and functions of new models, new automotive components or new technologies. It is not a Repair Manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. For further information about maintenance and repair work, always refer to the current technical literature.NoteReference3 Power supplyBatteryIn the Audi A3 ’13, the vehicle battery is housed in the engine bay and protected by a battery box. Battery size and type are dependent on engine version, trim and country specification. Standard batteries, EFB batteries and AGM batteries are used. Vehicles with petrol engines and a start-stop system are equipped with an EFB battery, while vehicles with diesel engines and a start-stop system are equipped with an AGM battery. Vehicles with an auxiliary heater generally have an AGM battery.EFBAn EFB (Enhanced Flooded Battery) can be regarded as a heavyduty wet-cell battery. The positive plate inside the battery is coated with an additional polyester scrim. This provides additional hold for the active battery material. The deep-cycle resistance is higher than that of conventional batteries. An EFB is charged in exactly the same way as a conventional battery.AGM batteryIn AGM (Absorbent Glass Mat) batteries, the battery electrolyte is held within a microporous glass matting. In addition to having higher deep-cycle resistance than an EFB battery, the AGM battery is noted for its leak-proof construction. When charging an AGM battery, it is important to follow the charger's operating instructions and, where applicable, to program the charger for AGM batteries.The following batteries are used in the Audi A3 ’13: Standard batteries • • • • • 44 Ah/220 A 51 Ah/280 A 60 Ah/280 A 61 Ah/330 A 72 Ah/380 A EFB • 59 Ah/280 A • 69 Ah/360 A AGM batteries • 58 Ah/340 A • 68 Ah/380 ABattery housingThe housings of the batteries used in the Audi A3 ’13 vary in length. On the battery bracket there are holes for three different lengths of battery housing. Hole 1 2 3 Battery housing length 212 mm 247 mm 278 mmHole 1 Hole 2Hole 3610_008 4 Fuses, relays and jump start terminalThe battery's positive terminal and the jump start terminal on the engine bulkhead are used for battery charging and jump starting.Jump start terminal on the engine bulkheadGround terminal with battery monitor control unit J367Battery positiveBattery Fuse rail on the e-box Designation of fuses in current flow diagram "SA"e-box with fuses and relays Designation of fuses in current flow diagram "SB"610_073Fuseholder and relay carrier under the dash panel, left Designation of fuses in current flow diagram "SC"FusesIn addition to the standard flat fuses, the space-saving mini fuses and the circuit breakers (thermal fuses), a new type of fuse is used in the Audi A3 ’13: the so-called J-Case fuse. The fuses are colour coded for easy identification:J-Case fusesFuse rating 20 A 25 A 30 A 40 A 50 A 60 AColour blue white pink green red yellow610_072A new gripping tool is available for removing and fitting this new type of fuse. It is housed in the e-box cover in the engine bay.Gripping tool for J-Case fuses610_071 5 NetworkingInstallation locations of control unitsSome of the control units shown in the overview are optional and/ or country-specific equipment. Refer to the current service literature for details of controls unit positions, as well as instructions for installation and removal.J387 J364J668 J104J794J250J500R242 J428 J685 J234 J255 E380 J844 J587J518 J745 J743 J533 J285 J764 J527 J525J623J791 J667 J519J386Key: E380 J104 J234 J250 J255 J285 J345 J364 J386 Multimedia system operating unit ABS control unit Airbag control unit ECD control unit (electronically controlled damping) Climatronic control unit Control unit in dash panel insert Trailer detector control unit Additional heater control unit Door control unit, driver side J387 J428 J492 J500 J518 J519 J525 J527 J533 Door control unit, front passenger side ACC control unit All-wheel drive control unit Power steering control unit Entry and start authorisation control unit Onboard power supply control unit Digital sound package control unit Steering column electronics control unit Data bus diagnostic interface6 R78 J772 J769J492J345 J843 J608J770610_007J587 J608 J623 J667 J668 J685 J743 J745 J764Selector lever sensors control unit Special vehicle control unit Engine control unit Headlight power module, left Headlight power module, right MMI display Twin clutch gearbox mechatronics Cornering light and headlight range control unit Electrical steering column lock control unitJ769 J770 J772 J791 J794 J843 J844 R78 R242Audi lane assist control unit Audi lane assist control unit 2 Reversing camera system control unit Audi parking system control unit Information electronics control unit 1 Vehicle tracking system interface control unit Headlight assist control unit TV tuner Front camera for driver assistance systems7 TopologyLight switch E1 Headlight power module, left J667Sliding sunroof control unit J245Wiper motor control unit J400Headlight power module, right J668Anti-theft alarm sensor G578Rain and light detector sensor G397Humidity sensor G355Power output module for left LED headlightAlarm horn H12Onboard power supply control unit J519Power output module for right LED headlightControl unit in instrument cluster J285Audi side assist control unit 2 J770Steering column electronics control unit J527Diagnostic port Multifunction steering wheel control unit J453Door control unit, rear driver side1) J926Door control unit driver side J386Door control unit, rear passenger side1) J927Door control unit passenger side J387Data bus diagnostic interface J533Trailer detector control unit J345NOx sender control unit J583 Engine control unit J623Entry and start authorisation control unit J518 Electrical steering column lock control unit J764NOx sender control unit 2 J881Seat occupancy recognition control unit J706Airbag control unit J234Vehicle tracking system interface control unit J843Front left seat belt tensioner control unit J854Special vehicle control unit J608Front right seat belt tensioner control unit J855Climatronic control unit2) J255Twin clutch gearbox mechatronics J743Selector lever sensors control unit J587Fresh air blower control unit J126Refrigerant circuit pressure sender G805Air humidity sender in fresh air intake duct G657Air quality sensor G2388 The topology shows all control units with connectivity to the data bus system. Some of the control units shown here are optional or country-specific equipment, or will be introduced at a later date.This diagrammatic representation of all possible control units is purely theoretical. The adaptive light and headlight range control unit J745, for example, is never fitted at the same time as the headlight range control unit J431, rather only one or the other.Adaptive light and headlight range control unit J745Headlight range control unit J431Multimedia system operating unit E380MMI display J685 Audi side assist control unit J769 Headlight assist control unit J844 Front camera for driver assistance systems R242 Digital sound package control unit J525ACC control unit J428Information electronics control unit 1 J794ABS control unit J104Battery monitor control unit J367Power steering control unit J500Alternator CTV tuner R78All-wheel drive control unit J492Reversing camera system control unit J772Audi parking system control unit J791Auxiliary heater control unit J364Auxiliary heating radio controlled receiver R64ECD control unit (electronically controlled damping) J250Key: Powertrain CAN bus Convenience CAN bus Extended CAN bus Infotainment CAN bus Diagnostics CAN bus Suspension CAN bus LIN bus Sub-bus systems MOST bus610_0011) 2)For five-door models only For more details of heater / air conditioning configurations, refer to SSP 609 "Audi A3 ’13".9 Overview of bus systemsBus system Powertrain CAN bus Convenience CAN bus Extended CAN bus Infotainment CAN bus Suspension CAN bus Diagnostics CAN bus MOST bus Cable colour Configuration Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Optical bus system Max. data transfer rate 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 150 Mbit/s Characteristic Not single-wire capable Not single-wire capable Not single-wire capable Not single-wire capable Not single-wire capable Not single-wire capable Ring structure: an open circuit leads to total system failure Single-wire capable Not single-wire capableLIN bus Sub-bus system (private bus)Electrical single-wire bus system Electrical two-wire bus system20 kbit/s 500 kbit/sNew features of the bus system• The convenience CAN bus and infotainment CAN bus are highspeed bus systems in the Audi A3 ’13 • New MOST bus – MOST150 • The control unit in the instrument cluster J285 is a convenience CAN user • The data bus diagnostic interface J533 is the master of LIN slave "multifunction steering wheel control unit J453" • The data bus diagnostic interface is not a MOST bus user • The information electronics control unit 1 J794 is the system and diagnostic manager for the MOST bus • The information electronics control unit 1 J794 is connected to the operating unit and MMI display via the sub-bus system The networking diagram on pages 8/9 provides a schematic overview of the communication paths of in-vehicle control units. The equipment level dictates which control units are installed in the vehicle. Here are just a few examples: • The headlight range control unit J431 is never fitted at the same time as the cornering light and headlight range control unit J745. • The Headlight Assist control unit J844 is never fitted at the same time as the front camera for driver assistance systems R242 • The seat occupancy recognition control unit J706 is only available in the North American market • The TV tuner is only available in certain markets10 Optical data bus system MOST150HistoryFor the first time in an Audi vehicle, an optical data bus system known as the MOST bus (MOST25 to be precise) is fitted in the Audi  A8 ’03. This data bus system is named after the "Media Oriented Systems Transport (MOST) Cooperation". This group is made up of various automobile manufacturers, their components suppliers and software companies, who joined forces to create a standardised high-speed data transfer system. The term "Media Oriented Systems Transport" denotes a network with media-oriented data transport. This means that, unlike in the CAN data bus, address-oriented messages are sent to a specific recipient. This technology is used in Audi vehicles to transfer data within the infotainment system. The data transfer rate on the MOST25 bus is approx. 25 Mbit/s.MOST150The MOST150 is used in the Audi A3 ’13 for the first time in an Audi vehicle. This developmental stage in MOST technology is six times faster than the MOST25 bus. The development process necessitated various modifications to MOST components. For instance, the transmitter and receiver units – Fiber Optical Transmitters (FOT) – had to be adapted. Other components, such as the optical connectors, the fibre optics and the electrical connections of the control units, are identical to those of the MOST25.System managerUp to three control units are integrated in the MOST bus in the Audi A3 ’13: • Information electronics control unit 1 J794 • Digital sound package control unit J525 • TV tuner R78 In the Audi A3 ’13 the information electronics control unit 1 J794 acts not only as the system manager for the MOST bus but also as the diagnostic manager - a function previously performed by the data bus diagnostic interface J533.Digital sound package control unit J525Information electronics control unit 1 J794TV tuner R78610_069Optical replacement control unit VAS 6778Diagnostics The ring break diagnosis procedure is identical to that of the previous MOST bus system. However, the inspection plan for the Audi A3 ’13 must be retrieved in the vehicle diagnostic tester using address word 5F. Even though the ring break diagnosis procedure remains unchanged, a modified tool – the optical replacement control unit VAS 6778 – must be used in the event of an optical fault in the MOST150 bus, due to the modified transmitter and receiver units in the control units.610_074 11 Control unitsBrief descriptionsOnboard power supply control unitDesignation Equipment Installation position Tasks Onboard power supply control unit J519 Always fitted Under the left-hand dash panel • • • • • • Central locking master Exterior light master Interior light master Antitheft alarm / optional equipment master, PR No.: 7AL Activation of various relays Activation of various convenience components: • Seat heaters • Heated spray nozzles • Windscreen washer pump • Headlight washer system pump • Reading in various switches and buttons • Reading in various sensors 09 • Convenience CAN bus user • J519 is the LIN master for: • LIN 1 – light switch E1; wiper motor control unit J400; combined sensor – rain and light detection sensor G397 and humidity sender G355 • LIN 2 – alarm horn H12 • LIN 3 – sliding sunroof control unit J245; antitheft alarm sensor G578 LIN 1 is distributed to two pins on J519. Wiper motor J400 is connected to pin B30. Rotary light switch E1 and the combined sensor – rain and light detection sensor G397 and humidity sender G355 – are connected to pin C28. This means that the control units connected to pin C28 are also affected in the event of a short circuit to positive or negative at pin B30.Diagnostic address Data bus communicationSpecial featureJ519610_009Reference For a detailed description of the onboard power supply control unit J519, refer to SSP 611 "Audi A3 ’13 – Electronics and Driver Assistance Systems".12 GatewayDesignation Equipment Installation position Tasks Data bus diagnostic interface J533 Always fitted Under the left-hand dash panel • • • • 19 • All CAN bus system users • LIN master of battery monitor control unit J367 and alternator • LIN master of multifunction steering wheel control unit J453 / optional equipment Not a MOST bus user Networking gateway Diagnostic master Energy management system control Master for multifunction steering wheel / optional equipmentDiagnostic address Data bus communicationSpecial featureJ533610_010Instrument cluster with driver information system (DIS)Designation Equipment Control unit in dash panel insert J285 Always fitted Versions: • Monochrome DIS without onboard computer, PR No.: 9S4 • Monochrome DIS with onboard computer, PR No.: 9S5 • Colour DIS with onboard computer, PR No.: 9S6 In the dash panel • Display of information relevant to the driver • Immobiliser master 17 Convenience CAN bus user For the first time in an Audi model, this system is a convenience CAN userInstallation position Tasks Diagnostic address Data bus communication Special featureJ285610_01113 Steering column electronicsDesignation Equipment Installation position Tasks Steering column electronics control unit J527 Always fitted On the steering column • Connects the steering column stock and the electrical components in the steering wheel to the vehicle electronics • Terminal management master for vehicles without advanced key 16 Convenience CAN bus user Transfers the LIN signals from the gateway to the multifunction steering wheel control unit J453 in models equipped with a multifunction steering wheelDiagnostic address Data bus communication Special featureJ527610_012Trailer detectorDesignation Equipment Installation position Task Diagnostic address Data bus communication Trailer detector control unit J345 Optional equipment, PR No.: 1D2 Behind the side trim on the left-hand side of the luggage compartment Interconnects the vehicle electrics and the trailer electrics 69 Convenience CAN bus userJ345610_01314 Heating / air conditioningDesignation Equipment Heater control unit J65 Air conditioning system control unit J301 Climatronic control unit J255 • Heating, PR No.: 9AC • Air conditioning system, PR No.: KH6 • Automatic air conditioning, PR No.: 9AK In the dash panel, centre Controlling: • Temperature • Blower • Air distribution 08 • • • • Convenience CAN bus user J65 is the LIN master of the fresh air blower J126 J301 is also the LIN master of the refrigerant circuit pressure sender G805 J255 is also the LIN master of the air quality sensor G238 and the air humidity sensor in fresh air duct G657Installation position TasksDiagnostic address Data bus communicationSpecial featureAll LIN slaves are connected to a LIN output.J65610_014J301610_015J255610_01615 Door electronics, driver sideDesignation Equipment Installation position Task Diagnostic address Data bus communication Special features Door control unit, driver side J386 Always fitted In the driver's door Controlling the electrical and electronic components in and on the driver's door 42 • Convenience CAN bus user • In 5-door models it is connected to the door control unit, rear driver side J926 via a LIN line • J386 acts as the substitute master for the central locking system in the event of failure of the onboard power supply control unit J519 • Activates the side marker lights in the driver's door mirrorJ386610_017Front passenger side door electronicsDesignation Equipment Installation position Task Diagnostic address Data bus communication Special feature Door control unit, front passenger side J387 Always fitted In the front passenger's door Controlling the electrical and electronic components in and on the front passenger's door 52 • Convenience CAN bus user • In 5-door models it is connected to the door control unit, rear passenger side J927 via a LIN line Activates the side marker lights in the front passenger door mirrorJ387610_01816 Advanced key / keyless entry and start authorisationDesignation Equipment Installation position Tasks Diagnostic address Data bus communication Special feature Entry and start authorisation control unit J518 Optional equipment, PR No.: 4F2 Under the dash panel • Reading in both capacitive sensors • Activation of the entry and start authorisation aerials B7 Convenience CAN bus user For the first time in an Audi model, the external aerials connected to J518 are not installed in the doors, rather on the vehicle underbody in the B-post area.J518610_019Vehicle trackingDesignation Equipment Installation position Tasks Diagnostic address Data bus communication Special feature Vehicle tracking system interface control unit J843 Optional equipment, PR No.: 7G9 Behind the side trim on the left-hand side of the luggage compartment • Requirement for installation of Audi Tracking Assistant Plus • Data exchange between the tracking assistant and other vehicle control units • 3D • 30, if an additional special vehicle control unit is fitted Convenience CAN bus user The tracking assistant is always fitted as a retrofit solution (even in new vehicles). The vehicle tracking system interface control unit J843 cannot be retrofitted.J843610_02117 Electrical steering column lockDesignation Equipment Installation position Tasks Diagnostic address Data bus communication Special features Electrical steering column lock control unit J764 Optional advanced key, PR No.: 4F2 On the steering column • Locking and unlocking the steering column • Terminal management master 2B Convenience CAN bus user • Can be replaced separately from the steering column • Immobiliser user • Reads in the entry and start authorisation buttonJ764610_020Special functionsDesignation Equipment Installation position Task Diagnostic address Data bus communication Special feature Special vehicle control unit J608 Optional equipment, PR No.: F5B Behind the side trim on the left-hand side of the luggage compartment To allow special functions, such as taxi, driving school etc., to be implemented. 3D Convenience CAN bus user The hardware control unit is identical to the vehicle tracking system interface control unit J843J608610_02218 Reversing cameraDesignation Equipment Reversing camera system control unit J772 Optional equipment Versions: • Parking aid plus with reversing camera, PR No.: 7X2+KA2 • Parking aid with reversing camera, PR No.: 7X5+KA2 Behind the side trim on the right-hand side of the luggage compartment • Rectifying and processing the raw images captured by the reversing camera • Transferring the processed images to the information electronics control unit 1 J749 6C Convenience CAN bus user • Video connections are mechanically encoded • Only two of the three connections are usedInstallation position Tasks Diagnostic address Data bus communication Special featuresJ772Reversing camera connectionUnusedElectrical Video output connection610_025Audi adaptive cruise control (automatic speed and distance control) Audi pre sense frontDesignation Equipment ACC control unit J428 Optional equipment for vehicles with: • S tronic, PR No.: 8T3 • Manual gearbox, PR No.: 8T5 • pre sense front, PR No.: 7W2 Behind the radiator grille below the number plate mount in the centre • Radar scanning of traffic • Controlling speed and distance 13 CAN-Extended bus user Independent braking to a standstill behind a vehicle driving ahead and independent restarting (ACC Stop & Go)Installation position Tasks Diagnostic address Data bus communication Special featureJ428610_04319 Auxiliary heaterDesignation Equipment Installation position Tasks Diagnostic address Data bus communication Special features Auxiliary heater control unit J364 Optional equipment, PR No.: 9M9 On the outer right side member • Defrosting the windows • Comfort mode for heated interior 18 • Convenience CAN bus user • J364 is the LIN master of the auxiliary heating radio controlled receiver R64 • The target time and not the starting time of the auxiliary heater is selected with the remote control • Cannot be replaced separately from the heating unitJ364610_024InfotainmentDesignation Equipment Information electronics control unit 1 J794 Standard Audi Radio, PR No.: I8A Optional equipment Versions: • MMI Radio, PR No.: I8B • MMI Navigation plus, PR No.: I8F, 7UG In the glove compartment Controlling the infotainment systems 5F • Infotainment CAN bus user • In MMI versions it is connected to the MMI display J685 and the multimedia system operating unit E380 via a private CAN bus • In the case of MMI versions, an electrically retractable screen is integrated in the dash panel • If the Bang & Olufsen Sound System and/or TV tuner is fitted, the information electronics control unit 1 J794 is the system manager as well as the ring break diagnostics master for the MOST busInstallation position Task Diagnostic address Data bus communicationSpecial featuresJ794610_02620 Sound amplifierDesignation Equipment Installation position Task Diagnostic address Data bus communication Digital sound package control unit J525 Optional equipment for models with Bang & Olufsen Sound System, PR No.: 9VS Under the seat at the front left Activation of the 14 loudspeakers 47 MOST bus usersJ525610_027TV tunerDesignation Equipment Installation position Task Diagnostic address Data bus communication Special feature TV tuner R78 Optional equipment, PR No.: QV6 In the luggage compartment, rear right TV reception, display in the MMI display J685 57 MOST bus users Availability is country-specificR78610_02821 Electronic Stabilisation Program ESPDesignation Equipment Installation position Tasks ABS control unit J104 Always fitted • In the engine bay on the right-hand side of the engine bulkhead in left-hand-drive models • In the engine bay on the left-hand side of the engine bulkhead in right-hand-drive models • • • • • • • 03 Suspension CAN bus user • The control unit can be replaced separately from the valve block using ESD protective mat VAS 6613 • The electro-mechanical parking brake is integrated in the ABS control unit. Address word 53 for electromechanical parking brake has been deleted. Anti lock braking system ABS Electronic Stabilisation Program ESP Traction Control System TCS Electronic Differential Lock EDL Electronic transverse lock Multicollision brake Electro-mechanical parking brake EPBDiagnostic address Data bus communication Special featuresJ104 Valve block610_029Power steeringDesignation Equipment Installation position Tasks Power steering control unit J500 Always fitted Connected to the steering gear • • • • 44 Suspension CAN bus user • Control unit with power steering motor and steering angle sender G85 can only be replaced together with the steering gear • G85 has no separate data bus connections; data is transferred via the power steering control unit J500 Power steering Servotronic – speed-dependent power steering Corrective steering intervention in combination with Audi active lane assist and park assist Corrective steering intervention in combination with ESPDiagnostic address Data bus communication Special featuresJ500610_030Reference For detailed descriptions of the suspension components refer to SSP 612 "Audi A3 ’13 – Suspension".22 All-wheel driveDesignation Equipment Installation position Task Diagnostic address Data bus communication Special feature All-wheel drive control unit J492 Standard equipment with quattro powertrain Connected to the rear axle gear Control of the Haldex coupling according to the driving situation 22 Suspension CAN bus user The control can be replaced separately and without removing the rear axle gearJ492610_031Parking aid / park assistDesignation Equipment Park assist steering control unit J791 Optional equipment Versions: • Rear parking aid, PR No.: 7X1 • Parking aid plus, PR No.: 7X2 • Audi parking system, PR No.: 7X5 Behind the left-hand dash panel • Reading in the ultrasound sensors and, depending on version, audible or visual obstacle warnings • If the Audi parking system is fitted, it also measures the parking spot and calculates the parking manoeuvre 76 Suspension CAN bus user The diagnostic address is now 76, having been 10 on previous Audi modelsInstallation position TasksDiagnostic address Data bus communication Special featureJ791610_03223 Audi magnetic rideDesignation Equipment Installation position Task Diagnostic address Data bus communication ECD control unit (electronically controlled damping) J250 Optional equipment, PR No.: 2H7 Under the right-hand front seat Adaptation of the damping characteristic 14 Suspension CAN bus userJ250610_033Engine control unitDesignation Equipment Installation position Task Diagnostic address Data bus communication Engine control unit J623 Always fitted In the engine bay between the battery and e-box Controlling the engine characteristic 01 • Powertrain CAN bus user • To comply with specific emission standards, the engine control unit J623 is connected to both NOx sender control units via a private CAN bus • Control units (petrol engine/diesel engine) have different plug connections • Immobiliser user • Vehicles with an antitheft alarm have an antitheft device (sheet metal cover with shear bolts) over the engine control unitSpecial featuresJ623Shear bolt 1 Antitheft protection Shear bolt 2610_03424 Airbag / Audi pre sense basicDesignation Equipment Installation position Tasks Airbag control unit J234 • Always fitted • Optional Audi pre sense basic, PR No.: 7W1 On the centre tunnel in front of the centre console • Deployment of the airbags • Audi pre sense basic • Deployment of the pedestrian protection system 15 • Powertrain CAN bus user • If Audi pre sense basic is fitted, it is the LIN master for the front left and right belt tensioner control units (J854 and J855 respectively) • In vehicles specified for the North American market, it is the LIN master for the seat occupancy recognition control unit J706 It also controls the pedestrian protection systemDiagnostic address Data bus communicationSpecial featureJ234610_035S tronicDesignation Equipment Installation position Task Diagnostic address Data bus communication Special feature Mechatronic unit for dual-clutch gearbox J743 Optional equipment for vehicles with S tronic On the gearbox Controling the dual clutch gearbox 02 Powertrain CAN bus user Dual clutch gearbox 0CW (7-speed, see fig.) or dual clutch gearbox 09D (6-speed) is used depending on engine version.J743610_03625 Selector lever sensorsDesignation Equipment Installation position Tasks Diagnostic address Data bus communication Special feature Selector lever sensors control unit J587 Optional equipment for vehicles with S tronic On the selector lever • Signalling the selector lever position • Signalling the tiptronic commands 81 Powertrain CAN bus user The control unit can only be replaced together with the selector leverJ587610_037Headlight range control on vehicles with bi-xenon headlightsDesignation Equipment Installation position Task Diagnostic address Data bus communication Headlight range control unit J431 Optional equipment for models with bi-xenon headlights, PR No.: 8IG Behind the left-hand dash panel Dynamic headlight range control 55 CAN-Extended bus userJ431610_03926 Headlight range control on vehicles with bi-xenon headlights and adaptive light or LED headlightsDesignation Equipment Adaptive light and headlight range control unit J745 Optional equipment for vehicles with: • Bi-xenon headlights with adaptive light, PR No.: 8IM • LED headlights, PR No.: 8EY Behind the left-hand dash panel • Dynamic headlight range control • Controlling the light profiles • Controlling the adaptive light 55 CAN-Extended bus user It is connected to the power modules for the left and right headlights via a private CAN busInstallation position TasksDiagnostic address Data bus communication Special featureJ745610_038Audi side assist (lane change warning system)Designation Equipment Installation position Task Diagnostic address Data bus communication Special feature Audi lane assist control unit J769 Audi lane assist control unit 2 J770 Optional equipment, PR No.: 7Y1 • In the rear right bumper J769 • In the rear left bumper J770 • To scan the peripheral area behind and to the side of the vehicle • To activate the warning lights in the door mirrors 3C • J769 (master) CAN-Extended bus user • J770 (slave) connected to J769 via private CAN bus The control units are mounted in the bumper cover. The system must be calibrated after removal and installation.J770J769610_04027 Headlight assistDesignation Equipment Installation position Task Diagnostic address Data bus communication Special feature Headlight assist control unit J844 Optional equipment, PR No.: 8G1 In the rear-view mirror Automatic activation and deactivation of the main beam taking oncoming traffic into consideration 20 CAN-Extended bus user Available with halogen headlights, bi-xenon headlights and LED headlightsJ844610_041Audi active lane assist (lane departure warning system) Headlight assist Traffic sign recognition Intelligent light systemDesignation Equipment Front camera for driver assistance systems R242 Optional equipment • Audi active lane assist, PR No.: 7Y4 • Camera-based traffic sign recognition, PR No.: QR9 • Intelligent light system, PR No.: 8G2 On the windscreen, above the base of the interior rear-view mirror Scanning and imaging of traffic, traffic signs and lane markers A5 CAN-Extended bus user Camera-based traffic sign recognition requires MMI Navigation plus and colour driver information displayInstallation position Task Diagnostic address Data bus communication Special featureR242610_04228 Exterior lightingLight switchThe light switch of the Audi A3 ’13 is a LIN slave of the onboard power supply control unit J519. The operating concept with the rotary switch and the control panel for the fog lights and/or rear fog light has been adapted to the Audi model range. The headlight range adjuster is fitted in models with halogen headlights only.Headlight range control adjuster E102Designation Equipment Installation position TaskLight switch E1 Always fitted Dash panel, driver side To indicate the driver's preferred light setting to the onboard power supply control unit None, LIN slave, measurement values and diagnostics via onboard power supply control unit J519 (master)Control panelRotary switchDiagnostic addressDisplay and instrument lighting controller610_045FunctionRotary switch: 0 Lights off (in some countries the daytime running light is switched on automatically at "terminal 15 on") The automatic daytime running light is switched on and off depending on the light sensor (this position is also prerequisite for the "headlight assist" and "intelligent light system" functions) Parking light Dipped beam Upper control panel: Fog light All-weather light in vehicles with LED headlights AUTOLower control panel: Rear fog lightElectrical connections and circuitThe four positions of the rotary switch, button operations and the position of the instrument lighting controller are read in by the onboard power supply control unit J519 via the LIN line. In addition, all commands for the switch lighting and the warning lamps of the individual functions are sent to the light switch by the onboard power supply control unit. The redundancy line is used to determine the plausibility of the switch positions. In the event of a short circuit or an open circuit in the LIN line or redundancy line, the emergency light function is activated by the onboard power supply control unit ("dipped beam on") and a diagnostic trouble code is entered in the fault memory of the onboard power supply control unit. The headlight range adjuster E102 is integrated in the light switch housing but is a separate component. Its information is transmitted to the headlight range control servomotors via a discrete line.Light switch E1 Headlight range control adjuster E102610_046Connections of E1: Pin 1 Pin 2 Pin 3 Pin 4 LIN Terminal 30 Terminal 31 Redundancy lineConnections of E102: Pin 1 Pin 2 Pin 4 Terminal 30 Terminal 31 Activation of the headlight range control servomotors29 HeadlightsIn the case of the Audi A3 ’13, a distinction is made between headlight versions: • • • • Halogen headlight / ECE1) and SAE2) Bi-xenon headlight / ECE1) and SAE2) Bi-xenon headlights with adaptive light, ECE1) only LED headlight / ECE1) and SAE2) To remove headlights, the bumper cover must first be taken off. In addition to the headlight end caps, the parts shown in the diagrams can be replaced. In the event of damage to the upper and inner headlight attachments, repair tabs can be attached to the headlight housing.Halogen headlightPR no.: 8IDLeft main beam bulb M30 Daytime driving light bulb, left L174Left parking light bulb M1Left headlight range control servomotor V48Turn signal bulb, front left M5Sidemarker2)Left dipped beam bulb M29610_047Light functions Daytime running light Parking light Dipped beam Main beam Turn signal Sidemarker2)Illuminants used Bulb H15 Bulb W5W Bulb H7LL Bulb H15 Bulb PSY24W LEDPower 15 watts 5 watts 55 watts 55 watts 24 watts 0.6 wattsActivation mechanism In the case of halogen headlights, the various light functions are activated by the onboard power supply control unit J519. The daytime running lights are dimmed for the duration of the turn signalling cycle (in the SAE2) version they are switched off ). The halogen headlights can be combiend with a headlight assist system.Adaptation for driving on opposite side of road It is not necessary to adapt the headlights. No further action is needed to meet the statutory requirements.1) 2)ECE = for the European market SAE = for the North American market30 Bi-xenon headlightPR no.: 8IG In the case of the bi-xenon headlight, the component parts shown here can be replaced. Exception: The LED module with its 2 LEDs for daytime running lights and parking light. In the event of a fault in this module, the headlight must be replaced.Left gas discharge lamp L13 Left headlight range control servomotor V48Turn signal bulb, front left M5 Sidemarker2)Left LED module for daytime running lights and parking light L176Left gas discharge lamp control unit J343 Left daytime running light and parking light control unit J860610_048Light functions Daytime running light Parking light Dipped beam Main beam (change-over by shutter) Turn signal Sidemarker2)Illuminants used 2 LEDs with plastic optical fibres dimmed to approx. 25 % Gas discharge lamp D3SPower 18 watts35 wattsBulb PSY24W LED24 watts 0.6 wattsActivation mechanism In the case of bi-xenon headlights, the various light functions are activated by the onboard power supply control unit J519. The daytime running lights are dimmed for the duration of the turn signalling cycle (in the SAE2) version they are switched off ). The left and right dipped beam shutter motors (V294 and V295 respectively) are used for changing over between low beam and high beam. The bi-xenon headlight can be combined with a main beam assist system (PR No.: 8G1).Adaptation for driving on opposite side of road It is not necessary to adapt the headlights. No further action is needed to meet the statutory requirements.31 Bi-xenon headlight with adaptive lightPR no.: 8IM Implementation of different light functions In the case of the bi-xenon headlight with adaptive light, a rotating roller is fitted between the gas discharge lamp and the lens. The roller has different profiles around its circumference. The various light functions are obtained by rotating the roller using the variable front lighting servomotors. In addition, the complete projection module - comprising the reflector, lens, gas discharge lamp and roller - can be swivelled sideways by the dynamic adaptive light servomotors (not shown) to produce the adaptive light. The bi-xenon headlight with adaptive light is not available for the North American market. In the case of the bi-xenon headlight, the component parts shown here can be replaced. The following inner components of the headlight cannot be replaced separately: • • • • • LED module for daytime running lights and parking light Sender for variable front lighting servomotors Swivel module position sensors Variable front lighting servomotors Dynamic adaptive light servomotorsLeft gas discharge lamp L13Left adaptive light bulb L148Left headlight range control servomotor V48 (concealed in diagram)Turn signal bulb, front left M5 Roller for light functionsLeft variable front lighting servomotor V446 Left LED module for daytime running lights and parking light L176 Left gas discharge lamp control unit J343 Headlight power module, left J667 Left daytime running light and parking light control unit J860610_049Light functions Daytime running light Parking light Dipped beam (profile on roller) Main beam (change of profile on roller) Motorway light (change of profile on roller) Town light (change of profile on roller and slight swivelling of projection modules) Tourist light (change of profile on roller) Adaptive light (swivelling of the projection module) Cornering light (activated on one side) Intersection light3) (activated on both sides) Turn signal32Illuminants used 2 LEDs with plastic optical fibres dimmed to approx. 25 % Gas discharge lamp D3SPower 18 watts35 wattsBulb H835 wattsBulb PSY24W24 watts Bi-xenon headlights with adaptive light and "intelligent light system"PR no.: 8G2 The optional "intelligent light system" can be ordered in addition to the bi-xenon headlights with adaptive light. The intelligent light system function also requires the front camera for driver assistance systems R242 in order to monitor the current traffic situation. Oncoming vehicles, vehicles driving ahead and built-up areas are detected by the camera. Depending on the current traffic situation, the intelligent light system continuously adjusts the headlight range between dipped and main beam.Front camera for driver assistance systems R242610_050Light functions Daytime running light Parking light Country road light (profile on roller) Main beam (change of profile on roller) Motorway light (change of profile on roller) Town light (change of profile on roller and slight swivelling of projection modules) Tourist light (change of profile on roller) Adaptive light (swivelling of the projection module) Cornering light (activated on one side) Intersection light3) (activated on both sides) Turn signalIlluminants used 2 LEDs with plastic optical fibres dimmed to approx. 25 % Gas discharge lamp D3SPower 18 watts35 wattsBulb H835 wattsBulb PSY24W24 wattsAdaptation for driving on opposite side of road Both in the case of the bi-xenon headlight with adaptive light and the bi-xenon headlight with adaptive light and intelligent light system, the headlight can be changed over for driving on the opposite side of the road by rotating the roller through 180°. These headlights can be completely changed over, i.e. the roller has all the required light profiles for both left and right hand drive. This means that only one hardware version of this headlight is needed. The tourist light is activated in the MMI. In the CAR menu, the setting "Lights for driving on left" or "Lights for driving on right" can be selected under the menu option "Exterior lighting". In models fitted with a navigation system, the headlights are changed over automatically when crossing international borders, if necessary.ECE = for the European market SAE = for the North American market 3) models with navigation only1) 2)33 LED headlightsPR no.: 8EY In the case of the LED headlights, all light functions are performed by LEDs. No fog lights are fitted in models equipped with LED headlights. The all-weather light function is available as a substitute. However, this function is confined to the ECE1) version due to statutory requirements and is not available in the SAE2) version.Left headlight range servomotorParking light / daytime running light / turn signalCornering lightLeft headlight fanDipped beam Sidemarker2) Main beamHeadlight range control power module LED power module (Dipped beam, main beam, cornering light, fan activation)LED control unit (Parking light, daytime running light, turn signal, sidemarker2))610_051Light functions Daytime running light Parking light Dipped beam All-weather light Motorway light Main beam Cornering light Intersection light3) Turn signal Sidemarker2)Illuminants used 4 LEDs (1x 3 LED chip, 1x 1 LED chip) dimmed to approx. 15 % 9 LEDs (2x 5 LED chip, 2x 2 LED chip)Power 14 watts41 watts8 LEDs (2x 4 LED chips) 4 LEDs (2x 2 LED chips) LEDs of both cornering lights 4 yellow LEDs (1x 3 LED chip, 1x 1 LED chip) LED36 watts 18 watts 36 watts 16 watts 0.6 wattsWhen the all-weather light function is active, several LEDs are switched off (shortening the headlight range and reducing the self-dazzle effect) and the cornering lights are switched on. The motorway light is produced by raising the light beam level using the headlight range control function. In the case of the intersection light, both cornerning lights are switched on (models with navigation only). None of these three light functions is legal for the North American market.Adaptation for driving on opposite side of road It is not necessary to adapt the headlights. No further action is needed in order to meet the statutory requirements.1) 2)ECE = for the European market SAE = for the North American market3)models with navigation only34 Fog lightPR no.: 8WB The Audi A3 ’13 can be fitted with fog lights. These are integrated in the bumper and equipped with a 35 watt H8 bulb. The fog lights are activated directly by the onboard power supply control unit J519. To replace the bulb, first the air intake grille and then the fog light must be removed from the bumper.Fog light bulb, left L22610_052Overview of light functionsThe descriptions of the individual headlights specify which light function is available for which headlight version.Country road light The country road light is an asymmetric light. It is activated when a driving speed of 50 kph is exceeded. In models equipped with a navigation system, the country road light is active unless the system has detected a built-up area or motorway driving. With the country road light function, the adaptive light may additionally be active.610_053Motorway light The motorway light is an asymmetrical light which illuminates the oncoming lane slightly better than the country road light. The motorway light is activated if the vehicle exceeds 110 kph for an extended period, and immediately if a speed of 130 kph is exceeded. In models equipped with a navigation system, the motorway light is activated when the vehicle is travelling faster than 80 kph and the navigation system recognises motorway driving.610_054Main beam The main beam is a symmetrical light. It can be activated by operating the main beam stalk, the main beam assist function or the intelligent light system.610_05535 Adaptive light The adaptive light adapts to the curvature of the corner depending on vehicle speed and steering angle, thereby illuminating the corner better. This function is active in a speed range of 10 kph to 110 kph.610_056Town light The town light is a symmetrical close-range light. It is activated at speeds of between 5 kph and 50 kph in models equipped with a navigation system if the navigation system detects a built-up area. The adaptive light cannot swivel when the "town light" function is active.610_057Cornering light The cornering light is produced by activating the G8 bulbs on one side in the bi-xenon headlights with adaptive light. The following conditions must be met in order to activate the cornering light: • sharp steering angle and driving speed of less than 70 kph or • activated turn signal and driving speed of less than 40 kph It is activated in addition to the country road light and the town light.610_058Intersection light The light function "Intersection light" is also available for models equipped with a navigation system. The intersection light is produced by switching on both cornering lights. It helps the driver to detect hazards from the side at road intersections and is activated ahead of the intersection. The intersection light is always lit in combination with other lights. It is activated in conjunction with the town light while driving in built-up areas (see diagram below) and in conjunction with the country road light while driving on country roads.Intersection lightCornering light610_05936 Headlight range controlManual headlight range controlModels with halogen headlights are equipped with a manual headlight range control system. Here, the driver is responsible for correct adaptation of the headlight range to the vehicle's load condition. The headlight range adjuster E102 is integrated in the light switch housing, above the instrument lighting adjuster. It is supplied by terminal 15 and terminal 31 and activates both headlight range control servomotors via a discrete line.Schematic diagram of the activation mechanism for halogen headlightsConvenience CAN busHalogen headlight (left-hand side of vehicle)Discrete linesOnboard power supply control unit J519Left parking light bulb M1 Left daytime running light and parking light bulb L186 Left dipped beam bulb M29 Left main beam bulb M30 Turn signal bulb, front left M5Terminal 15 Terminal 31Headlight range control adjuster E102Discrete lineHeadlight range control servomotor V48610_060Dynamic headlight range controlAudi A3 ’13 vehicles with gas discharge headlights or LED headlights are equipped with a dynamic headlight range control system. Depending on the altitude and movement of the vehicle, headlight range control servomotors V48 and V49 correct the range of the headlights. The headlight range control configurations described below are available for the bi-xenon headlights and the bi-xenon headlights with adaptive light.Schematic diagram of the activation mechanism for bi-xenon headlightsConvenience CAN busBi-xenon headlight (left-hand side of vehicle)Discrete linesOnboard power supply control unit J519Left daytime running light and parking light control unit J860 Turn signal bulb, front left M5 Left gas discharge lamp control unit J343Extended CAN busHeadlight range control unit J431Discrete linesHeadlight range control servomotor V48Discrete lineRear left vehicle level sender G76 610_06137 Schematic diagram of the activation mechanism for bi-xenon headlights with adaptive lightConvenience CAN busBi-xenon headlight with adaptive light (left-hand side of vehicle) Discrete linesOnboard power supply control unit J519 Left daytime running light and parking light control unit J860 Turn signal bulb, front left M5 Left gas discharge lamp control unit J343Extended CAN busAdaptive light and headlight range control unit J745Power output module for left headlight J667Private CAN bus (sub-bus)Discrete linesDiscrete linesHeadlight range control servomotor V48 Left dynamic adaptive light control servomotor V318 Left variable front lighting servomotor V446 Left adaptive light bulb L148 Front left vehicle level sender G78Rear left vehicle level sender G76610_062Schematic diagram of the activation mechanism for LED headlightsConvenience CAN busLED headlights (left-hand side of vehicle) Discrete linesOnboard power supply control unit J519LED control unit (Parking light and daytime running light / turn signal) (Sidemarker with SAE1))Extended CAN busAdaptive light and headlight range control unit J745Private CAN bus (sub-bus)LED power module (Dipped beam, main beam and cornering light)Discrete lines Discrete lineLeft headlight fanRear left vehicle level sender G76Headlight range control power moduleDiscrete linesLeft headlight range control servomotor610_0631)SAE = for the North American market38 Headlight range control in vehicles with wheel damping electronicsThe Audi A3 ’13 can optionally be equipped with wheel damping electronics. These vehicles have four senders for monitoring the vehicle's ride height. They are read in via discrete lines in the electronically controlled damping control unit J250. The electronically controlled damping control unit J250 is a suspension CAN user and transfers information on vehicle ride height via the data bus to the installed headlight range control unit (varies depending on headlight version).Schematic diagram of the activation mechanism for vehicles with wheel damping electronicsHeadlight range control unit J4311)Discrete lineHeadlight range control servomotors1)Data bus diagnostic interface J533Adaptive light and headlight range control unit J7452)Private CAN bus (sub-bus)Power module for headlights2)Discrete line Suspension CAN bus Extended CAN busHeadlight range control servomotors2)Adaptive light and headlight range control unit J7453)Private CAN bus (sub-bus)Power module for headlight range adjustment3)Discrete lineHeadlight range control servomotors3)ECD control unit (electronically controlled damping) J250Discrete linesFront left vehicle level sender G78Front right vehicle level sender G289Rear left vehicle level sender G76Rear right vehicle level sender G77610_064with bi-xenon headlights with bi-xenon headlights with adaptive light 3) with LED headlights1) 2)39 Tail lightsIn the Audi A3 ’13 the light functions of the rear lighting are distributed to the tail lights in the rear end and the tail lights in the rear hatch. A distinction is made between the following versions of the tail lights: • Basic tail lights (in combination with halogen headlights) • LED tail lights (in combination with bi-xenon headlights, bi-xenon headlights with adaptive light and LED headlights) The onboard power supply control unit J519 activates the tail lights irrespective of version.Basic tail lightPR no.: 8SABrake/tail light 1Tail light 2Brake/tail light 3Turn signalReversing light610_065Light functions Brake light Tail light 1 Tail light 2 Rear fog light Tail light 3 Turn signal Reversing lightIlluminants used Bulb W21W Bulb W16W Bulb H21W Bulb PY21W Bulb H6WActivation mechanism 100 % 21 % 31 % 100 % 10 % 100 % 100 %Power 21 watts approx. 5 watts approx. 5 watts 21 watts approx. 2 watts 21 watts 6 wattsThe tail lights are also activated if the vehicle is equipped with a Coming Home / Leaving Home function. The rear fog light and the reversing light are deactivated when the rear hatch is open.The rear hatch light bulbs can be accessed by a service flap. The side light must be removed in order to replace a bulb.40 LED tail lightPR no.: 8SKTurn signalReversing lightRear fog lightBrake lightTail light610_066Light functions Brake light Tail light Rear fog light Turn signal Reversing lightIlluminants used 9 LEDs 2 LEDs with plastic optical fibres Bulb H21W 20 LEDs Bulb H6WActivation mechanism 100 % 100 % 100 % 100 % 100 %Power approx. 3.5 watts approx. 2 watts 21 watts approx. 3.5 watts 6 wattsThe tail lights are also activated if the vehicle is equipped with a Coming Home / Leaving Home function. The rear fog light and the reversing light are deactivated when the rear hatch is opened.The bulbs of the rear hatch light can be accessed via a service flap. LEDs cannot be replaced. If faulty, the tail light in question must be replaced.41 High-level brake lightThe high-level brake light is integrated in the rear spoiler and, comprising a total of 48 LEDs, provides additional brake lighting. The component parts of the high-level brake light cannot be replaced. If faulty, the complete component must be replaced. This is only possible after removing the rear spoiler.High level brake light bulb M25610_067Number plate lightsThe number plate lights on the Audi A3 ’13 use LED technology irrespective of tail light version. Both number plate lights are clipped into the rear hatch panel, and each has two LEDs. As with the high-level brake light, they are activated by the onboard power supply control unit J519.610_06842 AnnexSelf Study ProgrammesFor further information about the technology of the Audi A3 ’13, refer to the following Self Study Programmes.610_075610_076610_077SSP 238 Data exchange on the CAN bus I, order number: 140.2810.57.20 SSP 269 Data exchange on the CAN bus II, order number: 140.2810.88.20 SSP 286 Audi New data bus systems – LIN, MOST, BluetoothTM, order number: 000.2811.06.20610_078610_079610_080SSP 609 Audi A3 ’13, order number: A12.5S00.93.20 SSP 611 Audi A3 ’13 Vehicle Electronics and Driver Assistance Systems, order number: A12.5S00.95.20 SSP 612 Audi A3 ’13 Suspension, order number: A12.5S00.96.2043 All rights reserved. Technical specifications are subject to change. Copyright AUDI AG I/VK-35 service.training@audi.de AUDI AG D-85045 Ingolstadt Technical status 04/12 Printed in Germany A12.5S00.94.20610Audi Vorsprung durch Technik