TECHNICAL DOCUMENTATION

SSP 613 Audi R8 Power Transmission

PDFEN76 pages8 MB
SSP 613 Audi R8 Power Transmission - PDF cover

This PDF is currently unavailable.

Read document text
Self Study Programme 613 For internal use onlyAudi R8 Power TransmissionAudi Service Training The Audi R8 sees Audi offering, for the first time, a high-performance sports car based on a mid-engine concept. The engine positioning fore of the rear axle helps to ensure a balanced weight distribution and a low centre of gravity. This basic configuration allows a high level of driving stability and good transverse acceleration. Driving dynamics are further enhanced by the combination of a bespoke mid-engine concept and quattro all-wheel drive, with a strong emphasis being placed on sportiness and driving enjoyment.Due to the mid-engine concept and the demands on driving dynamics, the quattro full-time all-wheel drive system in the Audi R8 has been implemented in a different way to previous Audi quattro drive systems. In the case of the mid-engine concept with quattro all-wheel drive in the Audi R8, drive is transmitted dynamically to the front axle by means of a viscous coupling. Furthermore, a limited slip differential in the rear axle drive improves rear axle traction under high transverse acceleration.613_006When buying the Audi R8, the customer can elect to change gear manually using the 6-speed manual gearbox with double-plate dry clutch or to drive away and change gear fully automatically using the optional R tronic gearbox. An innovative selector mechanism allows the driver to make the choice of driving in Automatic mode or changing gears manually. In addition, the driver can select Sport mode. Want to find out more about the technology behind this power transmission system? If so, read on and learn all you need to know about power transmission in the Audi R8.613_007This self study programme teaches a basic knowledge of the design and functions of new models, new automotive components or new technologies. It is not a repair manual. Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. Always refer to the current technical literature when carrying out maintenance and repair work.!NoteReference2 ContentsIntroductionMid-engine concept with quattro all-wheel drive ________________________________________________________________________________________________________ 4Selector mechanismSelector mechanism – manual gearbox ___________________________________________________________________________________________________________________ 6 Clutch pedal switch F36 ____________________________________________________________________________________________________________________________________ 8 Reversing lights switch F4 _________________________________________________________________________________________________________________________________ 9 Selector mechanism – R tronic ____________________________________________________________________________________________________________________________ 10 Special aspects of operating R tronic ____________________________________________________________________________________________________________________ 12 Operating noise of R tronic ________________________________________________________________________________________________________________________________ 13Front axle drive 0AZSpecifications _______________________________________________________________________________________________________________________________________________ 15 Viscous coupling ___________________________________________________________________________________________________________________________________________ 16 Lube oil supply _____________________________________________________________________________________________________________________________________________ 18 Operating instructions _____________________________________________________________________________________________________________________________________ 19Manual and automatic gearboxesSectional view of basic gearbox ___________________________________________________________________________________________________________________________ 20 Specifications _______________________________________________________________________________________________________________________________________________ 22 6-speed manual gearbox 086 _____________________________________________________________________________________________________________________________ 23 Automated 6-speed manual gearbox 086 – R tronic ___________________________________________________________________________________________________ 24 Gear set – internal shift mechanism – synchromesh ___________________________________________________________________________________________________ 26 Rear axle drivewith limited slip differential _____________________________________________________________________________________________________________ 28 Lube oil supply _____________________________________________________________________________________________________________________________________________ 30 Gear oil cooling _____________________________________________________________________________________________________________________________________________ 32ClutchDouble plate clutch ________________________________________________________________________________________________________________________________________ 34 Clutch control – manual gearbox _________________________________________________________________________________________________________________________ 35R tronic – hydraulic control unitSystem overview ___________________________________________________________________________________________________________________________________________ 36 Hydraulic diagram __________________________________________________________________________________________________________________________________________ 38 Selector mechanism – R tronic ____________________________________________________________________________________________________________________________ 40 Clutch control – clutch adaptation – measured values _________________________________________________________________________________________________ 42 Electro-hydraulic shift mechanism _______________________________________________________________________________________________________________________ 46 S-CAM _______________________________________________________________________________________________________________________________________________________ 48 Shift sequence – gear-changing __________________________________________________________________________________________________________________________ 50 Basic setting – shift adaptation – self-diagnostics – measured data __________________________________________________________________________________ 54 Putting gearbox into neutral after certain system malfunctions _____________________________________________________________________________________ 56Electronic control unitAutomatic gearbox control unit J217 ____________________________________________________________________________________________________________________ 58 Basic settings – adaptations ______________________________________________________________________________________________________________________________ 59 Encode control unit ________________________________________________________________________________________________________________________________________ 59 Functions – displays/warnings ____________________________________________________________________________________________________________________________ 60 Functions – ignition key removal lock ____________________________________________________________________________________________________________________ 61 Functions – starter control unit ___________________________________________________________________________________________________________________________ 61 Function diagram __________________________________________________________________________________________________________________________________________ 62 CAN information exchange ________________________________________________________________________________________________________________________________ 64 Sensors ______________________________________________________________________________________________________________________________________________________ 66 Actuators ____________________________________________________________________________________________________________________________________________________ 70ServiceTow-starting/towing _______________________________________________________________________________________________________________________________________ 73AnnexIndex ________________________________________________________________________________________________________________________________________________________ 74 Test your knowledge (Part 1) _____________________________________________________________________________________________________________________________ 45 Test your knowledge (Part 2) _____________________________________________________________________________________________________________________________ 653 IntroductionMid-engine concept with quattro all-wheel driveThe outstanding performance is the quattro® all-wheel drive system is based on a weight distribution of 44 : 56 in favour of the rear axle. If needed, up to 420 Nm of drive can be transmitted dynamically to the front wheels by a viscous coupling.Manual selector mechanism with 6-speed manual gearbox or automatic selector mechanism with shift by wire technology in the R tronic, see page 10. R tronic shift actuator, see page 36 or the shift unit in the manual gearbox, see page 6 Limited slip differential, see page 28Drive shaft6-speed manual gearbox 086 or optional automated 6-speed manual gearbox 086 (R tronic)R tronic hydraulic unitThe manual gearbox 086 and the R tronic use a near-identical basic gearbox. This is a full synchromesh 6-speed manual gearbox. A high synchronisation capacity and short throws allow slick gear-shifting. A double plate clutch transmits the engine power to the gearbox.The R tronic has an electro-hydraulic shift unit which provides for drive-away and performs gear changes fully automatically. This type of gearbox is therefore referred to as an automated manual gearbox. Several aspects of the basic gearbox have been modified for this purpose. The transmission ratios are identical to those of the manual gearbox, but in both cases they are adapted depending on engine type.4 Front axle drive of 0AZ with viscous coupling, see page 14613_008Schematic diagram of power flowFront axle differentialDrive conceptThe quattro concept in the Audi R8 is a slip-controlled all-wheel drive system. The rear axle is the main drive axle. Engine torque is transferred through a spur gear to the rear axle differential, where a limited slip differential ensures a continuous flow of drive torque even under high transverse acceleration. Engine torque is transmitted to the viscous coupling through a second spur gear in the front axle drive, i.e. without the centre differential. Depending on the speed differential between the front and rear axles, the viscous coupling transfers a defined amount of torque to the front axle drive. Here, an open differential distributes the torque equally to the front and rear. The EDL control unit is specially adapted to the R8 drive concept and assists torque distribution in the usual way.Front axle drive Viscous coupling – transmits a defined amount of torque to the front axleDrive shaft – transfers the drive torque to the front axle gearbox. It is located inside the engine (it runs through the engine oil pan), which means it is not visible from the exterior.Rear axle differential with limited slip differential Rear axle drive spur gearFront axle drive spur gearManual gearbox gear set613_009 5 Selector mechanismSelector mechanism – manual gearboxDirection of travelSelector cable for gear selectionThe Audi R8 with manual gearbox is equipped with a gate shift system which allows short and slick gear changes and provides exact feedback on the gear engaged. The high-quality matt finish aluminium used underscores the sporty character of the Audi R8. To start the engine on models with a manual gearbox, the clutch must be fully depressed. This information is provided by the clutch pedal switch F36 on the clutch slave cylinder as a precaution against unintentional drive-away at start. Shift movements are transmitted from the selector mechanism to the gearbox via two selector cables (Bowden cables). The robust housing and lever parts as well as the high-quality bearings and joints in the selector mechanism and on the gearbox shift unit provide for very direct transfer of shift commands to the gearbox. In addition to the high-quality finish, a very direct and sporty shift feel is conveyed.Selector cable for shift gate selectionThe selector cables are set using the quick-release fasteners on the gearbox.Reversing lights switch F46 Overview of the external and internal shift mechanismsBall joints in the joint forks provide for direct transfer of shift movements.Shift locks on the selector shaft (and selector lever)613_010Direction of travelSelector cable for shift gate selectionSelector cable for gear selection613_011 7 Clutch pedal switch F36To start the engine on models with a manual gearbox, the clutch must be fully depressed. This is indicated by the clutch pedal switch F361) on the clutch slave cylinder. This measure safeguards against unintentional drive-away at start.1)The clutch pedal switch is also referred to in some service documents as clutch position sender G476. This can lead to irritation and confusion with the clutch position sender first mentioned on page 40.Clutch pedal switch F36 – mounted on the clutch slave cylinderCircuit diagram – clutch pedal switch F36Movement of the piston with ring magnet on actuation of the clutch pedal Ring magnet – is located on the piston of the clutch slave cylinderReed contact 1 (NC contact) – CCS signalPosition of ring magnet when clutch pedal is in home positionSignal for deactivation of cruise controlShift point 1 Reed contact 1 Shift point 2 Reed contact 2613_012Signal for start enable (interlock)613_013Maximum clutch pedal travelReed contact 2 (NC contact) – start enable signalNotes on operation The gate shift selector offers sporty gear-shifting and a sporty look. When changing gate, e.g. to shift from 2nd to 3rd gear (or vice versa), the shift lever and the finger of the aluminium gate can come into contact with one another during the gearshift. This produces an audible clicking sound because it is not possible to use a damper element for noise reduction. It is therefore important to ensure, firstly, that the selector mechanism is set correctly and, secondly, to ensure that gearshifts are performed exactly.Possible collision point when shifting from 2nd to 3rd gear135Launch Control Program A Launch Control Program is available for the R8 with V10 engine and manual gearbox. The Launch Control Program provides maximum power delivery from a standing start. Refer to the user manual for details of requirements, operating instructions and other information.R246Normal position of selector lever – in centre of shift gate 3/4613_014 8 Reversing lights switch F4The reversing lights switch F4 is supplied with term. 15 via a fuse. As soon as the selector lever is moved into the reverse gate, switch F4 connects term. 15 directly to the onboard power supply control unit J519. The onboard power supply control unit J519 actuates the reversing lights and relays the signal for the automatic anti-glare rear-view mirror Y7 to the gateway J533 by convenience CAN bus. The gateway, in turn, supplies the corresponding control units via their respective bus systems. The information supplied by the reversing lights switch F4 is required for the following functions: • Activation of the reversing lights • Automatic anti-glare rear-view mirror/door mirror • Activation of the front passenger door mirror fold-away function • Activation of the parking aid or reversing camera • Audi hold assist (ESP)Shift detent of the manual gearboxManual gearbox shift unit – engaged in R positionShift detents of the selector shaft and selector lever – shown here engaged in R positionReversing lights switch F4Selector shaft Detent for each of the gears and for the home position of the shift finger (and the selector lever) in the centre of shift gate 3/4. The ball socket in the selector shaft is on one side only.This axial detent is effective only outside the neutral position.613_015The illustration shows the shift detent in the neutral/home position of shift gate 3/4.9 Selector mechanism – R tronicIn the R tronic there is no mechanical connection between the selector mechanism and the gearbox. Selector lever positions and shift commands are registered, evaluated by the gear lever sensors control unit J587 and sent to the gearbox control unit J217 by CAN data bus. The gearbox control unit controls the electro-hydraulic control unit on the gearbox based on this information. This control mode is referred to as "shift by wire". The R tronic selector mechanism differs not only visually from the selector mechanisms of the other automatic gearboxes. The shift diagram has been specially adapted to suit the functional principle of the automated manual gearbox. The selector lever has two lockable normal positions (left and right positions) from which the corresponding functions can be selected (see Fig. 613_018).Selector lever position display Y5Sport program button E541 – is read in by selector lever sensors control unit J587. The information "Sport mode" is relayed from J587 to the gearbox control unit J217 and to the engine control unit by CAN data exchange. Refer to page 64 for further information.Refer to function chart on page 62Hall sensorsSelector lever sensors control unit J587613_016The selector lever sensors control unit J587 ... determines the selector lever positions for the gearbox control unit, … controls the LEDs in the selector cover and in the selector lever position display Y5, … transmits all information to the automatic gearbox control unit J217 by powertrain CAN bus, … is the interface to the sport program button E541. The selector lever positions are monitored by multiple Hall sensors. At the bottom end of the selector lever there is a permanent magnet which controls the corresponding sensors according to the selector lever position. The selector lever sensors of the J587 evaluate the signals and transmit the selector lever positions to the gearbox control unit J217. J217 utilises this information to identify the driver's input and controls the valves of the hydraulic control unit to engage the corresponding gears and clutch functions.613_017O-ring for noise reductionPermanent magnetBottom end of selector lever10 Selector lever in left-hand normal positionSelector lever in right-hand normal positionOperationSelector lever in left-hand normal position From the locked left-hand normal position, the drive can select Automatic mode (by moving selector to "A"), issue manual shift commands (by moving selector to + or –) or put the gearbox into neutral. In the locked left-hand selector lever position, the gearbox may, depending on prior selection, either be in neutral or engaged in a forward gear. When the engine is running, the brake pedal must be depressed in order to select Automatic mode or to engage a gear1).Selection of automatic modeSelection of forward gear or upshiftSelector lever sensors control unit J587Downshift613_018Selection of neutral position Selector lever in left-hand normal position613_019Selector lever in right-hand normal position From the locked right-hand selector lever position N, reverse gear can be selected by pulling the selector lever back to R. To select reverse gear ... … the vehicle must be stationary … and the brake pedal must be depressed with the engine idling1). In the locked right-hand selector lever position, the gearbox may, depending on prior selection, either be in neutral or engaged in a forward gear. Gearbox neutral position When changing from one locked normal position to the other, the gearbox is put into neutral (no gear is selected). To this end, the brake pedal must be depressed when the engine is at a standstill. This prevents the vehicle from rolling away unintentionally.Selection of neutral positionSelection of reverse gear Selector lever in right-hand normal position613_020Selector mechanism system malfunction In the case of the following malfunctions, the adjacent message is indicated: • Malfunction in the selector lever sensors control unit J587 • Interruption in the power supply to the selector mechanism • Interruption in the data bus connection to the selector mechanism If the gearbox was in Manual mode when the malfunction occurred, it switches over to Automatic mode. Gears can still be shifted manually using the selector paddles on the steering wheel. Reverse gear can no longer be selected. First gear can be selected from the neutral position using the + selector paddle.1)Selector lever Faulty: No reverse gear!613_021To aid maneouvring the vehicle, the brake must first be depressed if the gearbox is kept in neutral for longer than 1 second.11 Special aspects of operating R tronicThere is no park position or parking lock. Since a gear can be engaged and the clutch closes automatically when R tronic is deenergised, the vehicle can be secured against rolling away by selecting either 1st gear or reverse (R) gear. To securely shut off the vehicle, the handbrake must also be applied (as is the case with a normal manual gearbox). If the gearbox is in neutral, a gear must be selected manually. A gear which has already been selected remains engaged after turning off the ignition. The engine can only be started when the footbrake is depressed. R tronic always shifts into neutral when the engine is started. This prevents the vehicle from driving away unintentionally when the accelerator is depressed. The driver can select 1st gear, reverse gear or neutral with the ignition turned on (without the engine running). To do so, the brake pedal must be depressed. Gear-shifting noise and the running noise of the hydraulic pump are audible. If the gearbox is in neutral after ignition is turned OFF, a gear can still be selected manually for approx. 30 sec. after applying the brake (as long as the selector lever position display is lit). The Audi R8 with R tronic does not have an ignition key removal lock. Gearbox in neutral If the neither the accelerator nor the brake pedal is depressed when the vehicle is stationary and the engine running, neutral is engaged automatically after 10 sec. Drive-away characteristics Gearboxes have specific drive-away characteristics. Automatic gearboxes usually produce a certain amount of drive torque when the engine is idling and a gear selected. This is known as "creep torque". The vehicle begins to move away if its is not held with the brake. R tronic dos not generate creep torque when the engine is idling and a gear selected. R tronic automatically opens the clutch wide and interrupts power flow when the vehicle is stationary, the engine idling and a gear selected. This state is similar to that which occurs with a manual gearbox when the clutch is depressed. No noticeable feedback is provided as to whether a gear has been selected or not. For reasons of safety, neutral is engaged after approx. 10 sec. when the engine is idling and a gear selected unless throttle or brake is applied during this time. Starting on gradients Due to the fact that R tronic does not produce creep torque, the vehicle will roll back from a stationary start on even the slightest of gradients if the brake is not applied. The driving characteristics are similar to those of the manual gearbox. The vehicle must be held with the handbrake or the footbrake. "Holding" the vehicle on gradients by balancing the clutch and accelerator pedal will result in heavier clutch wear and cause the clutch to overheat. Refer to page 44. Audi hill hold assist is optional. If a gradient is detected and the footbrake is applied when the vehicle is stationary, the built-up brake pressure is held for a short time after releasing the brake. This aids starting on gradients by eliminating rollback. Driving in Manual mode (tiptronic) Manual mode (Tip-in function) can be selected by operating the shift paddle on the steering wheel or by moving the selector lever into the plus or minus position. In this case, Manual mode remains permanently activated. To change over to Automatic mode, the selector lever must be moved towards "A". By encoding the gearbox control unit accordingly, the Tip-in function can be adapted in such a way that it automatically switches back to Automatic mode a defined amount of time after a Tip command is issued using the steering wheel shift paddles. Refer to page 59 for further information. Driving in Sport mode During normal operation in automatic mode, the shift operations are configured with an emphasis on comfort. This results in longer shift times. A sporty setup can be provided for the driving and shift characteristics by selecting Sport mode (button E541). Sport mode is effective during both the automatic and manual shift modes. In Automatic mode, the shift points are adjusted to higher engine speeds and the shift times reduced. In both the Manual and Sport modes, the emphasis is on performance. The gearshifts are very short and crisp. The gearbox does not shift up automatically when when a certain engine speed is reached. A kickdown function is available in manual Sport mode. The basic principle is: the higher the engine speed and load, the faster the gearshift. Customers who are accustomed to the "normal automatic gearbox" may object to the at times abrupt gear changes. However, this characteristic is integral to the philosophy of this sports car. Sport mode also has an impact on the engine control unit. The ECU changes over to a more spontaneous accelerator pedal characteristic and the exhaust flaps are opened earlier.12 Blip of throttle during downshifts Downshifts are always executed with a blip of the throttle. The lower the engine speed, the lower the intensity at which the throttle is blipped. In Sport mode and Manual mode, the blip of the throttle is particularly pronounced at high engine speeds. When downshifts are performed at an engine speed of approx. 2500 rpm, the blip of the throttle is relatively light and barely noticeable.Launch Control Program A Launch Control Programm is available in the R8 with R tronic. The Launch Control Program provides maximum power delivery when accelerating from a standing start. Refer to the user manual for details of requirements, operating instructions and other information.Operating noise of R tronicR tronic is an automated manual gearbox. As is the case with a manual gearbox, a clicking sound can be heard from the gearbox when engaging and changing gears. The "idler gear rattle" typical of manual gearboxes may also be audible. Idler gear rattle is caused by uneveness in the rotational motion of an internal combustion engine. These rotary oscillations are transmitted to the gearbox gear set. Due to design-related backlash between the fixed gear and the idler gear as well as the inertia of the idler gears, the traction and thrust flanks of the gear teeth may collide with one another in a rhythmic fashion. This manifest itself as a rattling noise, which generally is noticeable when the engine is idling and when coasting at low speed and low engine load. This characteristic is particularly marked when the gearbox is at operating temperature. This effect is enhanced by sound reflection, e.g. if the vehicle is in an enclosed space or when driving along narrow lanes between buildings with the window open. Idler gear rattle can be reduced by vibration damping measures, e.g. in the clutch plate, but it usually cannot be eliminated entirely. The electro-hydraulic control unit of the R tronic is a largely independent system, since hydraulic pressure is supplied by an electrically driven oil pump. This is why it is possible to perform gearshifts and actuate the clutch even when the engine is not running. The R tronic hydraulic system operates at a system pressure of 40 to 50 bar. The oil pump produces this pressure and admits a certain amount of oil into a pressure accumulator. When the shut-off pressure of approx. 50 bar is reached, the pump is deactivated. The system is supplied with pressure from the pressure accumulator, and the pump is reactivated when the starting pressure of 40 bar is achieved. If the ignition is not turned on for a prolonged period of time, e.g. because the vehicle is parked, the pressure decreases slowly as a result of internal leakage. To ensure that the system is immediately ready for operation, the oil pump is activated as soon as the driver's door is opened if the oil pressure is below the starting pressure. The pump can be heard running. The auxiliary water pump can also be a source of audible operating noise when the engine is not running. When the hot engine is shut off, the auxiliary water pump can run on for up to 7 minutes. Gearshifts are performed at a higher pressure for the first 100 km. This allows for higher shift forces if the selector mechanism is new and has not been run in yet. This measure is also taken if a gearbox control unit has been replaced (refer to page 58).Starter control unit See page 61.Displays in the driver information system (DIS) See page 60.Special features and instructions for operation of the clutch Refer to "Clutch" on page 44.13 Front axle drive 0AZThe front axle drive is driven directly by the manual gearbox without an intermediate centre differential. A viscous coupling is integrated in the front axle drive. If necessary, it transmits up to 160 Nm of torque to the pinion shaft. Input torque is increased by a factor of 2.6 to approx. 420 Nm by the final drive ratio. This torque is distributed equally in the centre differential to both front drive wheels. The viscous coupling reacts to differences between the input and output speeds and transmits only a small amount of drag torque if the speed differential is small. This compensates for differences in speed between the front and rear axles, e.g. when cornering (small speed differential). Consequently, there is no need for a centre differential.613_022Viscous coupling mount from January 2010Silicone oil filler hole sealViscous couplingThe silicone oil filler hole seals and the pressure relief valve are composed of different sectional planes.ASilicone oil filler hole sealPressure relief valve From week 02/2009B14 SpecificationsDesignation Manufacturer Torque capacity Viscous coupling Final drive ratio Oil supply Front axle drive 0AZ GETRAG 450 Nm 160 Nm at 100 rpm of slip 37/14 (2.643 : 1) • Axle oil in final drive – bevel box / difference and all bearing points (one oil supply) – no change interval – lifetime filling • Special silicone oil in the viscous coupling (hermetically sealed housing) approx. 21.5 kg (incl. oil)WeightViscous coupling mount to January 2010To avoid having to replace the flange shafts in order to change the shaft oil seals, the shaft oil seals are press-fitted more deeply than in normal production. Consequently, the lip seal of the shaft oil seal runs on a new liner. As a result, the sensitive lip seal is subjected to less stress, which in turn improves durability and leak-tightness.Key: A B Production insertion depth Service insertion depthBABA613_024 15 Viscous couplingThe viscous coupling is a kind of fluid clutch. It consists of a hermetically sealed clutch housing and a corresponding number of inner and outer plates. The outer plates mesh with the clutch housing (torque input). The inner plates mesh with the output hub (torque output). The clutch housing is filled with a special-grade silicone oil. This silicone oil has a relatively low viscosity at normal temperature and becomes increasingly viscous when heated. The inner and outer plates have circular and slotted recesses around their entire circumference. The space between the plates is filled with silicone oil. The plates do not come into contact with one another in the normal operating range. Due to the presence of silicone oil between the plates, only a small amount of drag torque is transmitted at low slip. This compensates for differences in speed between the front and rear axles, e.g. when cornering (low speed differential). When the speed differential between the outer plates and the inner plates increases, the silicone oil is sheared off at the recesses in the plates. This generates heat, which makes the silicone oil more viscous. The result is transmission of power between the torque input and the torque output of the viscous coupling to an extent dependent on the speed differential and heating.Outer plate Silicone oil Torque input Clutch housing Torque outputSeal613_025Inner plateSchematic diagram of the viscous couplingInner plateOuter plate Silicone oil Clutch housingPressure relief valve From week 02/2010Output hub with inner plate carrier – torque outputSeal Lube oil port Torque input Lube oil portSilicone oil filler hole sealSeal Outer plate Inner plateSilicone oil613_026 16 The rule of thumb with a viscous coupling is that the greater the slip, the greater the amount of torque transmitted. Potentially this could even lead to 100% transmission of power for a short period of time. This characteristic of the viscous coupling is known as the "hump effect" (see diagram). The hump effect is caused by a sharp increase in temperature and the accompanying rise in pressure inside the clutch housing. The hump effect causes mechanical friction between the inner and outer plates, resulting in a sharp increase in the amount of torque transmitted. The speed difference decreases markedly between the outer and inner plates. The silicone oil therefore incurs less friction and cools down, which in turn reduces the amount of power transmitted. This process begins anew if the load on the clutch is maintained. The torque and power transmission configuration (characteristic) of a viscous coupling is mainly dependent on the following parameters: • Inner and outer diameters of the plates • Number of plates • Viscosity of the silicone oil • Filling level of the silicone oilThe viscous coupling in the Audi R8 is rated to transmit approx. 160 Nm of torque at a speed differential of 100 rpm. The viscous coupling should not incur hump even under heavy load. A rapid increase in torque is not desirable for reasons of driving dynamics. To prevent hump from occurring, a pressure relief valve is built into the clutch housing (from February 2009). If too much load is placed on the viscous coupling, the temperature and pressure in the clutch housing will rise sharply. If the pressure exceeds approx. 20 bar, this causes the pressure relief valve to open, which in turn reduces the amount of torque transmitted and prevents hump from occurring.Outer plate, torque increase without pressure relief valve1st activation threshold of the pressure relief valve 2nd activation threshold of the pressure relief valve (if load is still present)Hump effectClutch torque613_001Characteristic curve of clutch slip as a function of slip and slip durationAs the speed differential increases, the clutch torque initially rises rapidly to a defined value of 160 Nm and then levels off. If the speed differential remains unchanged, a hump effect will occur after a certain period of time. The time at which the hump occurs is essentially dependent on the speed differential, duration of slip and operating temperature. This cannot be exactly predicted.If the viscous coupling is placed under extreme load, the pressure relief valve opens and silicone oil is discharged from the clutch housing. The amount of torque which is transmitted by the viscous coupling is permanently reduced after the pressure relief valve has been activated. The silicone oil cannot be checked or refilled. If complaints are received concerning power transmission, the viscous coupling must be replaced. The silicone oil does not mix with the axle oil and deposits in the oil pan. The performance of the final drive and differential is not affected.In sections of the outer plates, each tooth is shaped in such a way that it serves as a spacer. This ensures that the required clearance between the inner and outer plates is maintained. The clearance space is filled with silicone oil. The plates do not come into contact with one another. Power is transmitted through the silicone oil.17 Lube oil supplyThe final drive 0AZ has an oil chamber which is filled with axle oil (hypoid oil). There is no change interval for the axle oil (lifetime filling). From model year 2008 onwards, the oil chamber vent is differently positioned and the previous rubber valve is replaced by a spring-loaded plate valve. When the final drive heats up, a slight excess pressure builds up inside the oil chamber, causing the valve to open. When the final drive cools down, a slight vacuum develops inside the oil chamber and decreases automatically over a prolonged period ( 12 hours) due to micro leaks. The viscous coupling has its own hermetically sealed oil supply, which is filled with special silicone oil (refer to page 16).Vent with rubber valve (until model year 2008)Vent with plate valve (from model year 2008)Axle oil filler and inspection screwAxle oil drain screw613_027 18 Operating instructions• For performance testing and road simulation, the Audi R8 may only be run on a permanently coupled 4-roller dynamometer. This means that the front and rear axle rollers must be interconnected so that the wheels can be driven at the same speed. • Continuous balancing of high speed differentials between the front and rear axles will damage the viscous coupling and the front axle drive. • If the prop shaft has been removed, the Audi R8 can be driven as a rear-wheel drive model. • A brake test can be safely conducted on a low speed dynamometer. A speed differential of less than 10 kph is not problematic and is acceptable for a period of less than 5 minutes. • The Audi R8 must not be towed with the front or rear axle elevated off the ground. Background: In the case of a speed differential between the front and rear axles, the viscous coupling is automatically engaged to transmit power. As a result, the raised axle can break away. If an axle is locked up, the viscous coupling or the front axle drive will incur damage. • At large steering angles, stresses occur in the front axle due to the toe-on on turns, causing the wheels to rub and produce a droning or rubbing noise. This effect is intensified by low aspect ratios, wide tyres, low ambient temperatures (cold tyres) and certain road surface conditions. This characteristic of the Audi R8 occasionally leads to complaints wrongly attributed to the front axle drive. • The viscous coupling is a maintenance-free part. The silicone oil cannot be checked or refilled. If the viscous coupling is faulty or ineffective, it must be completely replaced.19 Manual and automatic gearboxesVentSectional view of basic gearbox6-speed manual gearbox 086The manual gearbox and the R tronic use an almost identical basic gearbox. This is a full synchromesh 6-speed manual gearbox. A high synchronisation capacity and short throws allow slick gear-shifting. A double plate clutch transmits the engine power to the gearbox.Port for venting the hydraulic clutch controlOil filler screwAutomated manual gearbox 086 – R tronicIn the case of the R tronic, an electro-hydraulic shift unit actuates the clutch and performs gear changes fully automatically. This type of gearbox is referred to as an automated manual gearbox. Several aspects of the basic gearbox have been adapted for this purpose. The gear ratios are absolutely identical to those of the manual gearbox, but in both cases are adapted according to engine. The differences between the manual gearbox and R tronic are shown on page 26.Input shaft – drive shaft (two piece)Input shaft connecting to front axle driveRear axle drivewith limited slip differentialProtective tube (fitted from model year 2009 onwards)Rear axle drive crown gearLimited slip differentialThis screw may not be used for checking the oil level (this will result in overfilling). This screw is no longer available on recent gearbox models (refer to workshop manual).613_029 20 The figure shows the 6-speed manual gearbox 086Drive shaft3rd gear Output shaft Rear axle drive spur gear Front axle drive spur gear 4th gear 6th gear5th gear 2nd gear 1st gear Reverse gear613_028Oil drain screwRear axle drive spur gearSpecial features of the gearbox • • • • Two-piece input shaft with spline Input shaft for front axle drive Final drive with limited slip differential, see page 28 Lubrication of specific bearing points, gearings and idler gears by means of the oil pump, see page 30 • Thermostat-controlled gear oil cooling (except for R8 GT), see page 32Gear oil filterRear axle drive pinion gearOutput shaft613_03021 SpecificationsService designation Plant designation Gearbox manufacturer Electro-hydraulic control unit manufacturer Torque capacity Final drive ratio Oil supply 6-speed manual gearbox 086 ML600-6A Oerlikon/Graziano – 600 Nm Refer to ETKA (electronic parts catalogue) Oil is supplied by means of an integrated oil pump Thermostat-controlled gear oil cooling by air-oil heat exchanger No oil change interval – lifetime filling approx. 95 kg (incl. oil) approx. 105 kg (incl. oil) Automated 6-speed manual gearbox 086 – R tronic SL600-6A Oerlikon/Graziano Magneti Marelli 600 NmWeightReversing lights switch F4 Shift unit with selector shaft and fingerShift locks in the shift unitBall bearing shift rods Gearbox input speed sender G182 (not functional in conjunction with manual gearbox, see page 68)Reverse gear shift forkThe shift forks are attached to the shift rods by means of grub screws1st and 2nd gear shift forks22 6-speed manual gearbox 086Gear oil filler screwVent for hydraulic clutch controlGearbox oil system ventProtective tube (fitted from model year 2009 onwards) Input shaft connecting to front axle driveRear axle drive with limited slip differential, see page 28Front axle drive spur gearRear axle drive spur gear613_03123 Automated 6-speed manual gearbox 086 – R tronicAudi has elected to use an R tronic automated manual gearbox in the R8. R tronic is notable for its near-lossless power transmission, low weight and ultra-slick gearshifts. R tronic cannot be compared to a typical automatic gearbox with torque converter or a double clutch gearbox. The main difference is that traction is interrupted completely during gearshifts. This can result in slight dive motion, which will often be considered annoying. Depending on driving profile and shift program, the gearshifts are comfort oriented or "short and slick". With the R tronic, comfort is secondary. The seemingly abrupt gear changes may not appeal to former owners of sports saloons (new converts and movers-up), although this is an integral part of the sports car driving experience. For further information on the special features of R tronic, refer to page 12.R tronic gear actuator, see page 36Shift locks on the shift rods and shift forksBearing for shift rods with Teflon anti-friction bushingsGearbox input speed sender G182, see page 68The shift forks are attached to the shift rods by means of clamping screws24 Electro-hydraulic clutch control ventGearbox oil system ventProtective tube (fitted from model year 2009 onwards)613_03225 Gear set – internal shift mechanism – synchromeshCommon design features and differences between the manual gearbox and R tronicCommon features1): • • • • • Input shaft – drive shaft (two piece) Bearing and synchromesh Output shaft Output shaft connecting to front axle drive Rear axle drive with limited slip differential Differences: • • • • Shift jaws of the shift forks Shift rod mounts Attachment of the shift forks to the shift rods Shift locksGear set with final drive, input and output shafts – manual gearboxInput shaft – drive shaft (two piece)Thick shift jaws2)Ball bearing shift rods613_033Input shaft connecting to front axle drive 4th gear Each shift fork has its own axial shift lock. 3rd gear 5th gear 2nd gear 1st gear Reverse The shift forks are attached to the shift rods by means of grub screws Flat shift rods for short shift throws and fast shift times2)6th gearBearing for shift rods with Teflon anti-friction bushesGear set – R tronicThe gear ratios of the individual gears and the final drive vary according to engine type. 2) R tronic has flatter shift jaws which reduce the rotation angle of the selector shaft from approx. 15° (manual gearbox) to approx. 7° when changing shift gates. This shortens the shift throws, which in turn cuts the reaction time of the gear actuator and allows short shift times to be achieved (see page 47).1)26 Synchromesh Gears 1, 2 and 3 have triple cone synchoniser rings. Gears 4, 5 and 6 have double cone synchroniser rings. To achieve high synchronisation capacity and long life, the friction faces are coated with a special sintered lining. Reverse gear has a brass single cone.Synchroniser ring Large lining ring Intermediate ring Small lining ring Inner ring Lining ring Synchroniser ring Sliding sleeve 3–4 Lining ring Inner ring 3rd gear pinion Synchroniser ringInner ring Lining ring Synchroniser ring4th gear pinion6th gear pinionSmall lining ring Intermediate ring Large lining ring Synchroniser ring Synchroniser ringSliding sleeve 5–65th gear pinion613_035Large lining ring Intermediate ring Small lining ring2nd gear pinion Synchroniser ringSliding sleeve 1–21st gear pinion Reverse gear pinion Reverse gear sliding sleeve613_036The shift forks are attached to the shift rods by means of clamping screwsIn the case of the R tronic, the shift positions and limit stops of each of the gears must be adapted to the gearbox control unit. The "gear actuator basic setting" function is available on the diagnostic tester for this purpose. For more information, refer to the workshop manual and page 54.613_034 27 Rear axle drivewith limited slip differentialIn both gearbox versions, a limited slip differential in the final drive improves traction at the rear axle. Particularly at high transverse acceleration, it ensures that drive torque flows continuously. Background The classic open differential always distributes drive torque evenly. The left and right wheels therefore transmit the same amount of force (50 : 50). Due to the dynamic distribution of wheel load, the wheel on the inside of the corner defines how much torque the wheels are able to transmit to the road when cornering, as it is the one which begins to spin first. In this case, the inner wheel cannot transmit any torque and therefore neither can the wheel on the outside of the corner, resulting in loss of traction. The same applies when one wheel is, for example, driving on ice, in which case the rear axle, again, cannot transmit any torque to the road. Accordingly, the wheels on the opposite side of the vehicle cannot transmit any torque to the road. However, a differential always has a certain amount of inner friction. This friction produces a small amount of "locking torque", which acts as a "assisting torque" on the other side of the vehicle. In the case of a limited slip differential, a certain amount of torque is transmitted from the faster-turning wheel to the slowerturning wheel (on the inside of the corner) depending on the limited slip value. This results in steering effects which counteract the steering direction during normal cornering. The vehicle initially has a tendency to understeer. This behaviour changes when cornering at high speed. The wheel on the inside of the corner is relieved of load and has a tendency to spin. The limited-slip differential transfers the torque to the wheel on the outside of the curve allowing the axle to continue transmitting torque to the road.Thrust ringDifferential caseMulti-plate clutchDifferential gearThe clutch plates are molybdenum-coated steel plates and therefore highly durable. The multi-plate clutch setting is made at the manufacturers and must not be adjusted.613_037Right thrust ring1)Differential side gear Left thrust ring1)613_038Axle spider of the differential gears (pay attention to correct direction of fitting) Differential gear1)Do not interchange parts.28 Design and function The drive torque transmitted from the drive pinion to the crown gear is transmitted from the differential case to both thrust rings. Each of the thrust rings has four wedge-shaped recesses in which the axle spider is mounted in bearings. The axle spider forms the axle journal for the four differential gears. The axle journals flatten off at the same angle as the recesses in the thrust rings. This ensures full surface contact between the swivel pins and the thrust rings. As soon as drive torque is input, the radial forces produced by the thrust rings and the axle journals act in opposite directions. The wedge-shaped recesses act like ramps (inclined plane), and the axle journals spread the thrust rings apart axially like a wedge. The axial contact pressures resulting from the wedge effect act on both the left and right multi-plate clutches and produce a loaddependent clutch torque. This clutch torque serves as a locking torque and produces the locking effect. The outer plates (steel plates) interlock with the differential case and the inner plates engage the differential side gears. As a result, a portion of the drive torque is transferred directly from the differential case to the gears.Axial contact pressures acting on the multi-plate clutchesRadial counterforce produced by the wheelsRadial drive force produced by the crown gearRelative movement between the axle journal and the thrust ringsForces in the limited slip differential (when driving forwards)Locking effect and slip value The locking effect of the limited slip differential is adapted to the vehicle and the desired driving dynamics. The lock-up effect is defined by the lock-up value. The slip value defines the maximum torque difference at both outputs of the differential (left and right) resulting from the locking effect. The limited slip differential in the Audi R8 has a nominal slip value of 25% under throttle and 45% when coasting. One of the adjustment parameters for the slip value is the ramp angle, since this is a key factor defining the pressure applied to the multi-plate clutches. Due to the fact that there are different ramp angles for driving under throttle and coasting, the locking effect is adapted to both different driving situations.Operating Instructions The limited slip differential has an all-mechanical action, is selflocking and becomes effective as soon as drive torque is input. This can place strain on the rear wheels when negotiating tight corners at high drive torque. When this occurs, the wheels have a tendency to rub. This manifests itself as noticeable vibration in the driveline.613_03929 Lube oil supplyThe gear set and the final drive are supplied with gear oil from a common oil supply. The same gear oil is used in both gearbox versions (manual gearbox and R tronic). Controlled lubrication is provided by an oil pump, which allows a low oil level to be maintained and guarantees lubrication even at high transverse and longitudinal acceleration. The low oil level reduces churning losses and improves efficiency. An oil cooler integrated in the oil circuit (air-oil heat exchanger) reduces the thermal load on the gear oil and gearbox components. A thermostat regulates oil flow to the oil cooler. The oil conveyed by the oil pump is initially channeled to the thermostat. Depending on the oil temperature, the oil is either channeled through the oil cooler or directly back to the gearbox. Oil ports in the gearcase parts distribute the oil to the lubrication points. The input and output shaft pinion bearings are lubricated through the hollow-drilled shafts. Cross holes in the shafts channel the oil to the bearing points.Gear oil cooler (not fitted in the Audi R8 GT; for weight reasons, the Audi R8 GT dispenses with a gear oil cooling system)Oil port for lubricating the final drive bearingOil port with inlet to the hollow-drilled input shaftOil port for lubricating the drive pinion setO-rings for sealing the oil ports at the gearcase partings Oil port with inlet to the hollow-drilled output shaft613_04030 A bypass thermostat with an expanding wax element is used as an oil temperature regulator, see overleaf.613_041Gear oil pumpThe gear oil pump is driven by the reverse idler gear of the reverse gear.Gear oil filter – no change interval Reverse gear reversing idler31 Gear oil coolingExpanding wax elementFunction of the bypass thermostat with expanding wax elementThermostat closed The expanding wax element also acts as the gate valve of the thermostat and regulates inflow into the radiator. In the closed state, a small quantity of gear oil flows through the bypass and back to the gearbox. The gear oil flows along the expanding wax element and heats it up.G KBypassG K613_042SealThermostat open Upwards of a temperature of approx. 75 °C, the plunger begins to push the expanding wax element down against the force of the spring. This opens the inlet to the radiator. The thermostat is fully open upwards of a temperature of approx. 90 °C.K GPlungerKey: G K from or to gearbox from or to radiatorG K613_043!Notes Impurities in the gear oil (e.g. wear, chips, emulsion) are also distributed throughout the cooling system and can deposit in the oil cooler and bypass thermostat. It is therefore important to carefully flush the cooling system after gearbox repair work and before replacing a gearbox. For this purpose, the lines must be disconnected from the thermostat and radiator in order to flush the individual components. Care must be taken to ensure that all impurities are flushed out of the system. If in doubt, components such as the oil cooler or thermostat must be replaced. If any impurities are left in the system, this will again lead to complaints or damage to the gearbox. Impurities can clog up the thermostat bypass, impairing the performance of or disabling the thermostat. If the cooling system is opened during repair work (draining the oil cooler), the oil must be heated to above the opening temperature of the thermostat (so that it is distributed throughout the system) in order to ensure that the gear oil level is set correctly.32 Special aspect of the Audi R8 GT Due to the lightweight design of the Audi R8 GT, no gear oil cooler is fitted. To maintain oil circulation, "short-circuit line" is fitted in place of the oil pressure lines running to and from the oil cooler.Oil pressure line (short-circuit line)Special aspect of checking the gear oil level (all) The previous gearboxes do not have an oil inspection plug. To check the oil level, the gear oil must be drained off completely and the gearbox refilled with the prescribed quantity. The what appears to be a oil inspection plug on the cover of the final drive (Fig. 613_046) of this gearbox must not be used for checking the oil level (this will result in a wrong reading). Recent gearbox models have an oil inspection plug which can be used to set the oil level correctly. All gearboxes have an oil filler screw and an oil drain screw.613_044Gear oil vent Oil filler screwObserve the instructions and information given in the workshop manual.613_045613_046Oil drain screw Previous gearboxes have an oil inspection plug here. This must not be used for checking the oil level.613_047Oil inspection plug (recent gearbox models only)33 ClutchDouble plate clutchFlywheel with encoder wheel for the engine speed senderBoth in the manual gearbox and in the R tronic, engine torque is transmitted by means of a double plate clutch. The advantage of the double plate clutch is its high torque transfer capability and durability in conjunction with a relatively small diameter. To keep clutch installation space to a minimum, a self-adjusting clutch pressure plate is dispensed with.Pressure plate with clutch platesStarter sprocketPressure plate 2 (ventilated)Pressure plate 1 SpacerClutch plate 2Clutch plate 1The clutch plates and the pressure plates form a unit and cannot be separated. Spacers are located between the tangential springs of pressure plates 1 and 2. They provide the necessary clearance between the clutch plates when the clutch is open. The spring connections, tangential springs and spacers must be in perfect condition to ensure that the clutch opens properly. In vehicles with R tronic, the basic setting procedure must be carried out with the diagnostic tester after replacing the clutch, among other things (see page 59).Spring connections (tangential springs)34613_048 Clutch control – manual gearboxHydraulic clutch control ventClutch slave cylinder with release bearingBrake fluidPipe/hose to clutch slave cylinder613_049In the case of both the manual gearbox and R tronic, clutch disengagement is provided by a hydraulicallly actuated release bearing. In the case of this design, the clutch slave cylinder and the release bearing form a unit which is installed concentrically relative to the gearbox input shaft and the clutch. This type of gearbox has no further levers or bearing points which cause increasing frictional losses over time in use. It also provides central, and therefore more even, clutch disengagement.As with conventional clutch controls, the manual gearbox uses brake fluid. The R tronic gearbox uses hydraulic fluid. Components which are rated specially for the fluid in use, e.g seals and O-rings, must not come into contact with the other fluid. Since the components are identical in terms of their design, they can easily be mixed up. For this reason, particular care must be taken to ensure that the correct parts are used. The manual gearbox has a standard-type clutch breather.35 R tronic – hydraulic control unitSystem overviewIn the case o the R tronic, gears are shifted and the clutch is operated electro-hydraulically by a hydraulic control unit. This comprises the R tronic hydraulic unit and the R tronic gear actuator. The hydraulic unit supplies the gear actuator with the required oil pressure. This purpose is served by a separate oil circuit (hydraulic fluid) with a system pressure of between 40 and 50 bar. The gear actuator is activated by the gearbox control unit. It changes gears and controls the hydraulic pressure applied to the clutch according to the instructions of the gearbox control unit. The key components of the gear actuator are: • Three electromagnetic valves for gear-shifting (N284, N285, N286) • One electromagnetic valve for clutch actuation (N255) • One pressure sensor (G270) • Two travel sensors (G604, G616) • Selector shaft with shift finger, gear lock, working piston and sensor lever • S-CAM The key components of the gear actuator are: • Reservoir • Hydraulic pump with electric motor (V387) • Pressure accumulatorHydraulic oil reservoir – the oil level is checked when the hydraulic system is depressurised (at 0 bar system pressure). The vehicle must be horizontal for this purpose (refer to workshop manual).Hydraulic pump motor V387Sealing cover (with or without vent hose, depending on version) Sensor lever Gear recognition sensor G6041) Hydraulic pump inletR tronic gear actuatorSupply pressure lineGear recognition sensor 2 G6161)Shift finger Gear lock Selector shaft with working pistonS-CAMNon-return valvePressure line to clutch slave cylinder Pressure accumulator1)Follow the instructions on page 66 on the replacement of sensors, the gear actuator and the gearbox.36 Sealing cover (with or without vent hose depending on version)Return lineGearbox hydraulic pressure sender G270Gear recognition sensor G6041)R tronic gear actuator1)Gear recognition sensor 2 G6161)Pressure line to clutch slave cylinderR tronic hydraulic unitClutch actuator valve N255 Gear selection valve 1 N284 Gear selection valve 2 N285 Gear selection valve 3 N286Pressure accumulator613_050Other components integral to the automation of manual gearbox 086, and therefore R tronic, are: • • • • • • Automatic gearbox control unit J217 – see page 58 Clutch slave cylinder – see page 40 Clutch position sender G476 – see page 67 Gearbox input speed sender G182 – see page 68 R tronic selector mechanism – see page 10 Various signals and information received from other control units by powertrain CAN bus or separate signal lines – see page 64Connection for hydraulic pump motor V387Hydraulic pump!Notes When performing work on the hydraulic control unit, care must be taken to ensure that the hydraulic system withstands high pressures (over 50 bar) even when the engine is at a standstill and the ignition OFF. There is a danger of injury. Before performing work on the hydraulic system, it must be ensured that the system is depressurised and that the hydraulic pump cannot be started. Refer to the workshop manual and the diagnostic tester.37 Hydraulic diagramClutch slave cylinder Clutch control mechanism vent Pressure piston of S-CAM brake2) Working piston of the selector shaft Selector shaftThrottle = R, 2, 4, 6Overrrun = 1, 3, 5Shift finger in neutral positionPressure accumulatorR tronic gear actuator613_051R tronic hydraulic unitdepressurised Suction pressure System pressure Key: G270 N255 N284 N285 N286 V387 Gearbox hydraulic pressure sender Clutch actuator valve (marked green1)) Gear selection valve 1 (not marked1)/3)) Gear selection valve 2 (marked white1)) Gear selection valve 3 (marked blue1)) Hydraulic pump motorNon-return valveFilter bypass valve Pressure filter Hydraulic pump Return line Suction filterThe hydraulic diagram is shown in a pressure and stress free state.Hydraulic oil reservoir1)The connectors for the electromagnetic valves are identical in design (they are not coded). To ensure that the connectors can be connected correctly, the wiring harness connecting to the electromagnetic valves is colour-coded. The valves are not usually colour-coded, which is why the electrical connectors are easily confused. To ensure that the connectors are reconnected to the matching valves, they must be marked unmistakably before disconnecting. For information on the electromagnetic valves, refer to page 70.2) 3)For information on S-CAM, refer to page 48. Special feature of N284: A pressure limiting valve is integrated in N284. It opens at approx. 80 – 90 bar and protects the hydraulic system against excess pressure. This pressure limiting function is not shown to ensure the simplicity of the hydraulic diagram.38 Pressure build-up613_052The electro-hydraulic control unit of the R tronic is a largely autonomous system. The hydraulic pressure is produced by an electrically driven hydraulic pump (V387). This means that gearshifts and clutch operations can be performed at terminal 15 "on" and without the engine running. A pressure accumulator provides a defined oil pressure volume. As a result, the system can operate for a certain amount of time without the pump running. The system pressure lies between 40 and 50 bar. The hydraulic pump starts up at terminal 15 "on" and if the pressure drops below the starting pressure of approx. 40 bar. When the switch-off pressure of approx. 50 bar is reached, the hydraulic pump is deactivated. The nonreturn valves maintain the pressure. The system is now supplied with pressure from the pressure accumulator. The hydraulic pump is reactivated by the gearbox control unit by means of a relay when a starting pressure of approx. 40 bar is achieved (see function diagram on page 62). The running noise of the pump is barely noticeable when the engine is running, but the pump can easily be heard running when the engine is at a standstill.Pressure holding613_053If the terminal 15 is not turned on for a lengthy period of time (e.g. because the vehicle is parked up), the pressure decreases slowly due to internal leakage. To ensure that the system is immediately ready for operation, the hydraulic oil pump is activated as soon as the driver's door is opened if the oil pressure has dropped below the starting pressure of 40 bar. In this case, the pump can clearly be heard running.!Notes When performing work on the hydraulic control unit, care must be taken to ensure that the hydraulic system will withstand high pressures (over 50 bar) even when the engine is at a stand