TECHNICAL DOCUMENTATION
SSP 616 Audi 1,2l and 1,4l TFSI Series EA211

This PDF is currently unavailable.
Read document text
Self Study Programme 616 For internal use onlyAudi 1.2l and 1.4l TFSI Series EA211 enginesAudi Service TrainingThe development aims for the new TFSI engine series were clearly outlined: the small 1.2 or 1.4-litre petrol engine was to be more fuel-efficient, lighter, more compactly dimensioned and offer cross-platform versatility. As well as all that, it had to be futureproof in terms of alternative fuels and new technologies. The results: • CO2 emissions up to 20 g per km lower • Nearly a whole litre fuel saving per 100 km • Weight reduced by as much as 30 % • Installed length up to 18 % shorter • Modified fitted position The EA211 engine series represents a new Audi petrol engine family comprising four-cylinder units specially developed for vehicles using the cross-platform modular component set (MQB).Compared with its predecessor (EA111), the EA211 series is an entirely new design. Only the cylinder spacing of 82 mm has been retained. Because the fitted position of the engines is set at an inclination of 12 degrees, the drive train, drive shafts and gearbox length can be standardised. That reduces the number of engine and gearbox variants within the Group's MQB system by nearly 90 %. A particular technical highlight is the selective cylinder shut-down feature on the 103 kW 1.4l version. It enables two of the four cylinders to be shut down when the situation allows, without the driver noticing any effect. The cylinder shut-down feature reduces the fuel consumption over the NEDC by 0.4 l/100 km (8 g CO2/km). Especially at moderate speeds in urban traffic, as well as on country roads, savings of between 10 and 20 % are even possible. A new benchmark in this class of engine.1.2l TFSI enginee-media This SSP contains a QR code which you can use to access additional interactive content, see "Information on QR codes" on page 50.616_015Learning objectives of this self-study programme In this self-study programme you will learn about the technology of Audi 1.2l and 1.4l TFSI engines. When you have worked through this Self Study Programme, you will be able to answer the following questions: • • • • How are the engines constructed? How is the engine's cooling system constructed? How do the engine's air intake and turbocharger systems work? How does the selective cylinder shut-down system on the 1.4l TFSI engine (103 kW version) work?2ContentsIntroductionBrief technical description __________________________________________________________________________________________________________________________________ 4 Versions _______________________________________________________________________________________________________________________________________________________ 5 Specifications _ ________________________________________________________________________________________________________________________________________________ 6Engine mechanicalsCylinder block _ _______________________________________________________________________________________________________________________________________________ 8 Crankshaft drive system and valve gear _ __________________________________________________________________________________________________________________ 9 Belt-drive timing gear ______________________________________________________________________________________________________________________________________ 10 Auxiliary unit drive system _________________________________________________________________________________________________________________________________ 11 Crankcase venting system __________________________________________________________________________________________________________________________________ 12 Activated charcoal filter system ___________________________________________________________________________________________________________________________ 15 Cylinder head ________________________________________________________________________________________________________________________________________________ 16Oil supplyOil circulation system _______________________________________________________________________________________________________________________________________ 18 Regulated oil pump _________________________________________________________________________________________________________________________________________ 19 Duocentric oil pump ________________________________________________________________________________________________________________________________________ 20 Sump _________________________________________________________________________________________________________________________________________________________ 21 Oil cleaning and cooling ____________________________________________________________________________________________________________________________________ 22Cooling systemIntroduction _________________________________________________________________________________________________________________________________________________ 23 System overview ____________________________________________________________________________________________________________________________________________ 24 Thermostat __________________________________________________________________________________________________________________________________________________ 25 Coolant pump _______________________________________________________________________________________________________________________________________________ 25 Cylinder head cooling ______________________________________________________________________________________________________________________________________ 26 Intercooler ___________________________________________________________________________________________________________________________________________________ 27Air intake and turbocharger systemsOverview _____________________________________________________________________________________________________________________________________________________ 29 Turbocharger ________________________________________________________________________________________________________________________________________________ 30Cylinder on demand (cylinder shut-down system)Introduction _________________________________________________________________________________________________________________________________________________ 32 Cam adjustment actuators _________________________________________________________________________________________________________________________________ 34 Function ______________________________________________________________________________________________________________________________________________________ 35 Deployment conditions for 2-cylinder mode _____________________________________________________________________________________________________________ 37 Shut-down and reactivation sequence _ __________________________________________________________________________________________________________________ 38 Function diagram (Audi A3 ’13) _ __________________________________________________________________________________________________________________________ 40Fuel systemOverview _____________________________________________________________________________________________________________________________________________________ 41Exhaust systemOverview _____________________________________________________________________________________________________________________________________________________ 42 Catalytic converter __________________________________________________________________________________________________________________________________________ 43Engine management systemSensors and actuators on 1.4l TFSI (103 kW) ___________________________________________________________________________________________________________ 44 Engine speed sensor G28 _ _________________________________________________________________________________________________________________________________ 46AppendixSpecial tools and workshop equipment _ __________________________________________________________________________________________________________________ 48 Scope of maintenance jobs _ ________________________________________________________________________________________________________________________________ 50 Information on QR codes __________________________________________________________________________________________________________________________________ 50 Self Study Programmes ____________________________________________________________________________________________________________________________________ 51 The self-study programme provides information on the fundamentals of the design and function of new vehicle models, new automotive components or new technologies. The self-study programme is not a repair manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. It is essential that you refer to the latest technical literature when carrying out maintenance and repair jobs.NoteReference3IntroductionBrief technical description• Four-cylinder in-line engine • Four valves per cylinder, double overhead camshafts (DOHC) • FSI petrol direct injection • Cast aluminium cylinder block • Turbocharger with indirect intercooler • Intercooler integrated in intake manifold (air/coolant heat exchanger) • Belt-drive timing gear • Cylinder management/cylinder shut-down system on one version of the 1.4l TFSI engine • Emission control system with ceramic underfloor catalytic converter and converter heating function using two-stage injection (homogeneity split) • Energy recovery system in overrunning mode • Start-stop system (model and market-dependent) • Mixture conditioning with fully electronic direct injection and electronic accelerator1.4l TFSI engine (103 kW)616_014 4VersionsThe EA211 engine series is used on various Audi models with different capacities. The engines have different features depending on the vehicle model and the market in which it is sold. The table below details the variants, versions and adaptations. Other technical data is listed on the following pages.Engine1.2l TFSI1.4l TFSIVehicle use Engine code Power output in kW (hp) Torque in Nm Exhaust emission standards GearAudi A3 '13 CJZA 77 (105) 175 • EU 5 plus • EU 2 ddk • 0AJ • 0CW • 0AH FSI yes noAudi A3 '13 CMBA 90 (122) 200 • EU 5 plus • 0CW • 0AJ FSI yes noAudi A1, A3 '13 CPTA 103 (140) 250 • EU 5 plus • A1: 02Q, 0CW, • A3 '13: 02S FSI yes yesFuel injection Turbocharged Cylinder on demandWeight reduction measures126 kg.Aluminium cylinder block -16 kgConnecting rod -0.6 kgTiming gear -0.6 kgTurbocharger -2.5 kgThanks to an ultra-light cylinder block made of die-cast aluminium, the new petrol engines are especially light at 112 and 114 kilogrammes respectively – the 1.4l TFSI has shed an impressive 22 kg compared with its cast-iron predecessor in the EA111 series. The lightweight design extends right down to the minutest details: the crankshaft is 20 % lighter while the conrods have been slimmed down by as much as 25 %. The crank-pins are hollow and even the aluminium pistons with their now flat crown have been optimised for weight. The cylinder shut-down components weigh a mere three kilos.-22 kg. Crankshaft -2.2 kg 104 kg.1.4l 90kW TFSI (EA111)1.4l 90kW TFSI (EA211)616_056 5Specifications1.2l TFSI engine Torque/power curveEngine code CJZA Power output in kW Torque in NmEngine speed [rpm]616_036Engine code Type Capacity in cm3CJZA Four-cylinder in-line engine 1197 77 (105) at 4500 - 5500 175 at 1400 - 4000 4 1–3–4–2 71,0 75,6 10,5 : 1 Bosch MED 17.5.21 Premium unleaded 95 RON • EU 5 plus • EU 2 ddk A3 '13Power output in kW (hp) at rpm Torque in Nm at rpm Number of valves per cylinder Firing order Bore in mm Stroke in mm Compression ratio Engine management system Fuel Exhaust emission standards Vehicle use61.4l TFSI engines Torque/power curveEngine code CMBA Power output in kW Torque in Nm Engine code CPTA Power output in kW Torque in NmEngine speed [rpm]616_037Engine speed [rpm]616_038Engine code Type Capacity in cm3CMBA Four-cylinder in-line engine 1395 90 (122) at 5000 - 6000 200 at 1400 - 4000 4 1–3–4–2 74,5 80 10 : 1 Bosch MED 17.5.21 Premium unleaded 95 RON • EU 5 plus A3 '13CPTA Four-cylinder in-line engine 1395 103 (140) at 4500 - 6000 250 at 1500 - 3500 4 1–3–4–2 74,5 80 10 : 1 Bosch MED 17.5.21 Premium unleaded 95 RON • EU 5 plus A1, A3 '13Power output in kW (hp) at rpm Torque in Nm at rpm Number of valves per cylinder Firing order Bore in mm Stroke in mm Compression ratio Engine management system Fuel Exhaust emission standards Vehicle use7Engine mechanicalsCylinder blockThe cylinder block is made of die-cast aluminium and is an opendeck design. The advantages and disadvantages of an open-deck design are: • Easier to manufacture from the point of view of casting technology as no sand core required (more economical) • More efficient cooling of the upper, hotter part of the cylinders compared with a closed-deck design • Less rigid design compared with a closed deck is counteracted by the use of metal cylinder head gaskets on modern engines • Minimal deformation of the cylinder liner when the cylinder head and cylinder block are bolted together • The slight cylinder liner deformation is easily accommodated by the piston rings and the oil consumption is lower The channels for pressurised oil supply and return and for crankcase venting are cast integral with the crankcase. That reduces the number of additional components and the manufacturing complexity. Cast-iron cylinder liners The cast-iron cylinder liners are individually cast inside the cylinder block. Their outer surface is very rough, which increases the surface area and improves heat transfer to the cylinder block. Furthermore, it forms a very good positively interlocking fit with the cylinder block.Knock sensor G61Aluminium cylinder block with open-deck designMain crankshaft bearingsOil baffle plateSump top sectionOil level/temperature sensor G266Sump bottom section616_006 8Crankshaft drive system and valve gearThe crankshaft drive gear has been designed with small moving masses and low friction in mind. The conrods and pistons are extensively optimised for light weight. Together with the small main and big-end bearings the engine weight and internal friction have thus been further reduced. The lightweight crankshaft with its five main bearings and four counterweights reduces the internal crankshaft forces and, therefore, the stress on the main bearings. The valve gear comprises two camshafts that operate the valves via roller-lever cam followers. One version of the 1.4l TFSI engine has a cylinder shut-down feature for which there are special sliding cam sleeves and positioners on the camshafts, see "Cylinder on demand (cylinder shut-down system)" on page 32.Crankshaft drive and valve gear on 1.4l TFSI engine without cylinder shut-down featureCamshaftsValves operated by roller-lever cam followersAluminium pistons with valve recessesLightweight trapezoidal connecting rodLightweight crankshaft with four counterweights616_019Pistons and conrodsThe pistons are made of die-cast aluminium. To reduce the thermal stresses, oil injectors spray engine oil onto the piston crown from underneath. The conrods are forged and have cracked big ends and lightweight shafts. The small end does not have a pressurised oil supply and is trapezoid in profile. The crank-pins are hollow and even the aluminium pistons with their now flat crown have been optimised for weight.616_039!Note The crankshaft must not be removed. For more information, refer to the latest service documentation.9Belt-drive timing gear(E.g. 90 kW 1.4l TFSI) The crankshafts are driven by a toothed timing belt. It is tensioned by an automatic tensioning roller that simultaneously helps to guide the timing belt by means of raised flanges. When removing and refitting components of the timing gear, the tensioning roller has to be levered back with the aid of special tools T10499 (12-point ring spanner) and T10500. A guide pulley on the tension side and the ctc crankshaft sprocket make sure the timing gear runs smoothly and quietly. Because of the lower belt forces, the force of the tensioner can be reduced. That results in lower friction and mechanical stresses on the timing gear as a whole. The lower vibration levels make for smoother and quieter running. A timing belt with a wear-resistant polytetrafluoroethylene (Teflon) coating is used. Due to its high-quality material specifications, the timing belt has a very long service life.Inlet camshaft sprocket with vane adjuster and adjustment range of 50° CR Exhaust camshaft sprocketTensioner pulleyGuide pulleyOil pump drive sprocket (1.4l TFSI only)ctc camshaft drive sprocketOil pump drive gearDifferent oil pumps are used depending on the engine variant. On the 1.4l TFSI engines the oil pump is driven by a maintenancefree toothed chain, see illustration. No chain tensioner is fitted in this case. The crankshaft sprocket is permanently attached to the crankshaft and cannot be removed. For more information on the regulated oil pump see page 19 The 1.2l version of the engine has a duocentric oil pump that runs directly off the crankshaft without using a chain drive system, see "Duocentric oil pump" on page 20.Toothed drive chain for oil pump (1.4l TFSI only) Oil pump sprocket (1.4l TFSI only)616_020Reference For more information on "ctc – crankshaft torsionals cancellation" refer to Self-study Programme 332 "Audi A3 Sportback".10Timing belt cover(E.g. 103 kW 1.4l TFSI) The timing belt is protected from dust and dirt by a threepiece timing belt cover. This extends the life of the timing belt. The centre section of the cover (aluminium) is a very solid design. It serves simultaneously as an engine mounting. If a repair operation only requires the timing belt to be removed, e.g. "Removing and refitting camshaft housing", the engine mounting can be left in place. There is sufficient space to tension the timing belt.Plastic cover with injection-moulded sealAluminium-silicon cover (engine mounting)Plastic cover with injection-moulded seal616_032Auxiliary unit drive systemA poly-V belt running off the crankshaft pulley drives the alternator and, if fitted, the air conditioning compressor. An automatic tensioner ensures the belt is correctly tensioned. On vehicles without air conditioning compressor, the belt only drives the alternator. The poly V-belt (Optibelt) is flexible and stretchable. Due to its design and the low levels of mechanical stress, a tensioning roller is not required. So that the engine occupies as little space as possible, auxiliary units such as coolant pump, air conditioning compressor and alternator are bolted directly onto the engine and sump without additional brackets.Crankshaft pulleyBelt tensionerAlternator pulleyA/C compressor pulley (if fitted)616_018 11Crankcase venting systemThe crankcase venting system runs internally, i.e. the cleaned blow-by gases flow through channels in the cylinder block to the intake pipe upstream of the turbocharger or into the intake manifold downstream of the turbocharger. The oil vapours are removed in the oil separator. It is made of plastic and is bolted onto the cylinder block.In-feed of blow-by gases on intake side of turbocharger (at high engine speeds)Blow-by feed-in pipeNon-return valve on turbochargerTurbochargerOil separatorThe gases flow from the crankcase into the oil separator. There, the large droplets of oil are separated out first by means of baffle plates and swirl channels in the coarse separator. Then the fine droplets are removed by large baffle plates in the fine separator.Inlet Coarse oil separator Connecting pipe to intake manifold module with calibrated diameter. The calibration limits the flow volume. As a result the pressure regulating valve can be dispensed with.Separation chamber outletOil separator housing cover Fine oil separatorOil returnsOil return from oil separator to sump below oil level Separation chamber in crankcase12Non-return valvesThe non-return valves control recirculation of the cleaned blow-by gases for combustion according to the pressure conditions in the aspiration system. If there is negative pressure in the intake manifold at idling or higher engine speeds, the vacuum effect opens the valve in the intake manifold module and closes the valve on the intake side of the turbocharger. If there is positive pressure in the intake manifold when the turbocharger is working, that pressure closes the valve in the intake manifold module. At the same time, the valve on the intake side of the turbocharger is opened by the pressure differential present. That means that the pressure on the intake side of the turbocharger is lower than the pressure inside the crankcase.In-feed point with non-return valve on intake side of turbochargerIn-feed point for fuel vapour from ACF systemInternal routing of blow-by gases through channels in the cylinder block and cylinder headIn-feed point for blow-by gases downstream of turbocharger on intake manifold module (at low engine speeds)Throttle valveIn-feed point downstream of turbocharger on intake manifold moduleIntake manifoldNon-return valve Oil separator module on cylinder block Blow-by feed-in pipe616_017 13Crankcase venting systemThe non-return valve is part of the crankcase venting system. It allows fresh air to circulate through the engine in order to carry moisture (condensation and fuel constituents) away from the inside of the engine and the sump. If there is sufficient negative pressure inside the engine, fresh air is passed from the clean side of the air filter into the engine and is subsequently fed back into the cylinders together with the blow-by gas via the crankcase venting system. To achieve that, the non-return valve must open at the slightest degree of depression inside the engine and conversely prevent contamination of the air filter element by oil mist. The routing of the hose may vary depending on the engine variant. The non-return valve in the cylinder head cover prevents the oil or unfiltered blow-by gas getting into the air filter.Hose connection on air filter boxNon-return valve616_04214Activated charcoal filter systemThe ACF system is basically the same as the usual design used on turbocharged petrol engines. On the Audi A3 '13, the ACF canister in which the fuel vapour is stored is located on the fuel filler neck on the rear right of the vehicle. The fuel vapour is fed into the intake air at two different points, depending on the engine speed. The activated charcoal filter solenoid valve 1, N80, opens the way for feeding in the fuel vapour and is controlled by the engine management ECU. At idling speed and at low to medium engine loads, fuel vapour is fed into the intake manifold, i.e. downstream of the throttle valve, due to the depression in the intake system. In the phase during which the system is under turbocharger boost pressure, the fuel vapour is fed into the system upstream of the turbocharger. Fuel vapour delivery is controlled by two non-return valves. Their function is identical to that of the non-return valves in the crankcase venting system.From activated charcoal filterActivated charcoal filter on fuel tankFuel vapour feed-in point into crankcase breather pipeIn-feed point with non-return valve on intake side of turbocharger To intake manifoldElectrical connectionActivated charcoal canister solenoid valve 1 N801In-feed into intake manifold downstream of throttle valve2Valve unit with: 1 Non-return valve for in-feed into intake side of turbocharger when there is positive pressure in the intake manifold2Non-return valve for in-feed into intake manifold when there is negative pressure in the intake manifold616_04315Cylinder headTechnical features• • • • Aluminium cylinder head with twin composite camshafts Four valves per cylinder Modular-design cylinder-head cover Variable inlet camshaft timing on all models, adjustment range 50 °CR, lockable in retarded position • Variable exhaust camshaft timing on 1.4l engine (103 kW) only, adjustment range 40 °CR, lockable in advanced position • Cylinder shut-down feature (model dependent), see "Cylinder on demand (cylinder shut-down system)" on page 32 • Central positioning of spark-plugs (at centre of valve constellation) • High-pressure fuel pump driven by inlet camshaft (four-lobe cams) • Integral exhaust manifold • Cross-flow cooling, see "Cylinder head cooling" on page 26Modular-design cylinder-head coverThe cylinder head cover is made of die-cast aluminium and forms a single, inseparable unit with the two camshafts. That means that the four-bearing camshafts cannot be removed. To reduce friction, the first bearing of each camshaft, which is subject to the greatest loads from the belt-drive timing gear, is a deep groove ball bearing. The cylinder head cover also accommodates the following components: • Camshaft timing adjustment valve 1 N205 • Exhaust camshaft timing adjustment valve 1 N318 (model-dependent) • Hall-effect sensor G40 • Hall-effect sensor 2 G163 (model-dependent) • Crankcase venting system non-return valve, see "Crankcase venting system" on page 14Hall-effect sensor 2 G163Hall-effect sensor G40Camshaft timing adjustment valve 1 N205Crankcase venting system non-return valveExhaust camshaft timing adjustment valve 1 N318616_040Integral exhaust manifoldIn the integral exhaust manifold, the four exhaust ports are routed inside the cylinder head to a central flange. The catalytic converter is mounted directly on that flange. As well as offering fuel-efficiency and thermal advantages, see "Cylinder head cooling" on page 26, this design solution saves around 2 kg in weight compared with a conventional exhaust manifold.Key to illustration on page 171 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 16616_034Cylinder head cover Camshaft timing adjustment valve 1 N205 Exhaust camshaft timing adjustment valve 1 N318 Intake cam adjuster for cylinder 2 N583 Intake cam adjuster for cylinder 3 N591 Exhaust cam adjuster for cylinder 2 N587 Exhaust cam adjuster for cylinder 3 N595 Hall-effect sensor G40 Hall-effect sensor 2 G163 Camshaft cover Deep-groove ball bearing Sliding cam sleeve Exhaust camshaft Coolant pump drive sprocket Roller-lever cam follower with support Valve spring retainer17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Valve stem oil seal Valve collets Valve spring Camshaft bearing cap Cylinder head cover gasket (metal gasket) Cylinder head Cylinder head gasket Fuel rail Fuel pressure sensor G247 Fuel injector for cylinder 1 – 4 N30 – N33 Oil pressure switch F1 Inlet valve Inlet camshaft Fuel pressure regulating valve N276 High-pressure fuel pumpLayout on 1.4l TFSI (103 kW) with cylinder shut-down feature1 2 3 6 4 5 7 8 91011 1213143031111516 17 18 19 2920 2827 212625242223616_021 17Oil supplyOil circulation systemThe oil system supplies all bearings, the piston cooling jets, the variable valve timing system, the valve gear and the turbocharger with sufficient oil for lubrication. Different oil pumps are used depending on the engine variant. Piston cooling jets spray oil onto the underside of the pistons to cool them.Oil pressure switch F1Oil supply to turbochargerCamshaft oil galleryConnections for engine oil coolerMain oil galleryRegulated oil pump (1.4l TFSI only)Sump top section with equipment mounting bracket Sump bottom section with Oil level/temperature sensor G266Oil filter on upper section of sump616_002 18Regulated oil pump(1.4l TFSI engines) A regulated oil pump is used on the 1.4l TFSI engines. Compared with other regulated oil pumps, this design is distinguished by a sophisticated control concept that enables even more efficient operation.OverviewCold start valveCoverPump driven gear (axially variable)Drive shaft with pump driving gearCompression spring of adjuster unit Control springControl pistonOil strainerPump casingIntake manifold616_003DesignIn terms of its basic design, the oil pump is a spur-gear pump. A particular feature of it is that one of the pump gears is axially variable (pump driven gear). By varying the axial position of the gear, the delivery rate and pressure in the oil circulation system can be influenced in a controlled manner. Control of the oil supply for operating the regulating piston is performed by the oil pressure regulating valve N428, see illustration on page 20.Regulating pistonPump driving gear Delivered oilPump driven gear (axially variable) Intake from sump616_022Reference More information on the regulated oil pump can be found in Self-study Programme 436 "Modifications to 4-cylinder TFSI Engine with Chain-drive Timing Gear".19Oil pressure control valve N428(1.4l TFSI engines only) The oil pressure control valve N428 is responsible for supplying the oil pressure for the regulating piston of the regulated oil pump. It is located on the rear of the cylinder block ("hot side" of the engine) and is operated by the engine management ECU. In the lower engine speed band the oil pressure regulating valve N428, which is connected to the power supply (Terminal 15), is connected to earth by the engine management control unit. That switches the oil pump to its lower pressure setting. The lower pump pressure is selected according to engine load, engine speed, oil temperature and other operating parameters. In that setting, the power required to drive the oil pump is reduced, thereby lowering fuel consumption. In the higher engine speed band or under high engine loads (acceleration at full power), the oil pressure regulating valve N428 is disconnected from the earth connection by the engine management control unit J623. That switches the oil pump to its higher pressure setting. In both pressure settings, the pump delivery is varied by means of the adjuster unit to suit variations in the engine's oil requirement based on engine speed.Oil channel in cylinder block Drive shaftAdjuster unitOil pressure regulating valve N428Regulating piston To oil filter616_046Duocentric oil pump(1.2l TFSI engine) On the 1.2l TFSI engine, a constant-pressure oil pump is used and takes the form of a duocentric pump. It is mounted on the timinggear end of the engine as a space-saving crankshaft-driven oil pump. That means that the inner rotor is mounted directly on the front end of the crankshaft journal. The regulated delivery of this pump provides a virtually constant oil pressure at anything above idling speed. The oil pressure of roughly 3.5 bar is maintained by a pressure regulating valve that is fitted in the oil pump housing. This ensures that sufficient oil pressure is always available in the engine regardless of how much dirt is in the oil filter. That prevents the oil pressure rising too sharply when starting the engine, for example, and damaging the gaskets.Outer rotorInner rotorBolt-on housing coverPressure-regulating valve616_045Reference More information on how a duocentric pump works can be found in Self-study Programme 432 "Audi 1.4l TFSI Engine".20Sump1.2l TFSI engineOn the sump there is a mounting for the air conditioning compressor. The oil filter is mounted directly on the sump, which is a cast aluminium design. A diaphragm valve in the oil filter prevents the oil running out of the filter when the engine is not running. Underneath the crankshaft there is an oil baffle plate which divides the crankshaft drive gear from the sump. In the sump itself are the oil level/temperature sensor G266 and the oil drain plug.Oil baffle plateSumpOil level/temperature sensor G266Mount for A/C compressorOil filter cartridge616_0101.4l TFSI engineThe oil filter is mounted on the top part of the sump, which is a cast aluminium design. Bolted onto it is the bottom part of the sump, which is made of sheet steel. On the top part of the sump there is a mounting for the air conditioning compressor. A diaphragm valve in the oil filter prevents the oil running out of the filter when the engine is not running. Underneath the crankshaft there is an oil baffle plate which divides the crankshaft drive gear from the sump. In the bottom part of the sump are the oil level/temperature sensor G266 and the oil drain plug.Oil baffle plateSump top sectionMount for A/C compressorOil filter cartridgeOil level/temperature sensor G266 Sump bottom section616_011 21Oil cleaning and coolingOn all engine variants in the EA211 series, the oil is cleaned by a cartridge filter. However, its position varies from model to model, see "Sump" on page 21. To cool the engine oil, it is pumped through the engine oil cooler by the oil pump. The engine oil cooler is mounted directly on the cylinder block underneath the intake manifold. It is in the form of an oil/coolant heat exchanger and, therefore, incorporated in the engine's coolant circulation system, see "Cooling system" on page 23.Coolant returnAfter passing through the engine oil cooler, the oil flows into the main oil gallery and on to other lubrication points in the engine, see "Oil circulation system" on page 18. The illustration below shows an example of the oil circulation system in the lower part of a 1.4l engine (90 kW).Coolant flowOil flow to cylinder headOil pressure switch F22Main oil galleryPiston cooling jetsMain bearingRiser pipe from oil filter to oil coolerSump top section with oil baffle plateEngine oil cooler (oil/coolant heat exchanger)Regulated oil pump (1.4l TFSI only)Oil level/temperature sensor G266Oil filter cartridgeSump bottom section616_033 22Cooling systemIntroductionThe cooling system has been entirely redesigned from scratch. For example, the coolant pump and its drive mechanism have been moved to the flywheel end of the engine. Fundamentally, the system is a twin-circuit cooling system which enables different coolant temperatures to be achieved in the cylinder head and the cylinder block. In the cylinder head, the cross-flow cooling system (from inlet side to exhaust side) achieves more even temperature distribution. In addition, the coolant channels in the cylinder head have been sufficiently generously dimensioned to be able to adequately cool the integral exhaust manifold. Mounted directly on the cylinder head is the thermostat housing and integral coolant pump. The coolant pump is driven by a toothed belt running off the exhaust camshaft.Cross-flow cooling in cylinder head with cooling of integral exhaust manifoldCoolant pump driven by exhaust camshaftConnections to heater matrixThermostat-tocylinder-head gasketThermostatCoolant-pump-tothermostat gasketFlow to radiatorReturn from radiator Coolant connections for oil coolerCylinder block coolant jacket open at top (open-deck design)616_024Reference More information on how the twin-circuit cooling system works can be found in Self-study Programme 432 "Audi 1.4l TFSI Engine".23System overview1 324 5 6 7 8 11 10 912 2 13 2 1415 17 18 19616_00516Key: 1 2 3 4 5 6 7 8 9 10 Coolant expansion tank Non-return valve Heater matrix Turbocharger Transmission oil cooler (ATF heat exchanger) Coolant temperature sensor G62 Thermostat 1 Coolant pump Thermostat 2 Engine oil cooler 11 12 13 14 15 16 17 18 19 Intercooler integrated in intake manifold Auxiliary heater Circulation pump V55 Flow restrictor Continued coolant circulation pump V51 Intercooler coolant radiator Radiator fan V7 Radiator outlet coolant temperature sensor G83 RadiatorCooled coolant Heated coolant ATFReference The basic method of operation of the twin-thermostat cooling system is described in Self-study Programme 432 "Audi 1.4l TFSI Engine".24ThermostatThe thermostat is integrated in the thermostat housing, which is mounted directly on the cylinder head. Inside the thermostat housing there are two thermostats for the twin-circuit cooling system.Thermostat 2 for cylinder blockTo heater matrixThermostat 1 Opens upwards of 87 °C and allows coolant to flow from the radiator to the coolant pump.Thermostat 2 Opens upwards of 103 °C and allows heated coolant to flow from the cylinder block to the radiator.The entire coolant circulation system is open.From heater matrixReturn from radiator Flow to radiatorThermostat 1 for cylinder head616_047Coolant pumpThe coolant pump is integrated in the thermostat housing. The complete module is bolted onto the cylinder head. It is sealed off from the coolant channels by EPDM (ethylene propylene diene monomer) rubber gaskets. One gasket sits between the coolant pump housing and the cylinder head, and the other between the coolant pump and the thermostat housing, see Figure 616_024 on page 23. The coolant pump is driven by a separate toothed drive belt running off the exhaust camshaft. That belt-drive system is on the flywheel end of the engine and is maintenance free. However, it does have to be replaced if the coolant pump is replaced.Coolant pump belt drive systemDrive belt coverThermostat 2 for cylinder blockExhaust camshaft Thermostat housing Coolant temperature sensor G62Coolant pump housing Coolant pump616_031!Note Before removing and when tensioning the coolant pump drive belt, always refer to the instructions in the Workshop Manual. Only a correctly tensioned drive belt will ensure the coolant pump functions correctly.25Cylinder head coolingIn the cross-flow cylinder head, the coolant flows from the inlet side around the combustion chambers to the exhaust side. There it splits into two areas, above and below the exhaust manifold. It flows through multiple channels, absorbing heat as it does so. From the cylinder head it flows into the thermostat housing where it mixes with the rest of the coolant. This design has a number of advantages: • The coolant is heated by the exhaust while the engine is warming up. The engine reaches normal operating temperature more quickly. That reduces fuel consumption and the vehicle interior can be heated sooner. • Because of the smaller exhaust surface area before it reaches the catalytic converter, the exhaust loses little heat when the engine is warming up and the catalytic converter heats up to its normal operating temperature more quickly despite the cooling effect of the coolant. • When the engine is under maximum load, the coolant is cooled to a greater degree and the engine can be run fuel and emission-efficiently at lambda = 1 over a wider band. That lowers fuel consumption at full power by as much as 20 % compared with turbocharged engines with external exhaust manifolds. In this case the components are protected by the cooling effect with an over-rich mixture.Coolant jacket and integral exhaust manifoldTo protect the engine and especially the cylinder head against overheating, the coolant temperature sensor G62 has been placed at the hottest point in the coolant flow, close to the exhaust manifold, see Figure 616_031 on page 25.Inlet sideMain coolant jacketConnection for coolant temperature sensor G62Upper coolant chamber Lower coolant chamber Exhaust port with flange connecting to turbochargerExhaust side616_02326IntercoolerAfter the intake air has passed through the turbocharger, it is very hot. It is heated up to temperatures as high as 200 °C, mainly due to the compression process, but also because the turbocharger itself is very hot. As a result, the air has a lower density, and less oxygen would enter the cylinders. So cooling it to a little above ambient temperature increases its density again and more oxygen is supplied to the cylinders. Furthermore, cooling the air reduces engine tendency to knock and prevents production of nitrogen oxides. To cool the air from the turbocharger, it is passed through an intercooler, which is integrated in the intake manifold module. The intercooler is in the form of an air/coolant heat exchanger and, therefore, incorporated in the engine's coolant circulation system, see "Cooling system" on page 23. The design and function of the intercooler in the intake manifold module are similar to that of a normal liquid cooler or radiator. A pipe carrying the coolant passes through a matrix of aluminium fins. The hot air flows over the fins and the heat of the air is passed to the fins. The fins transfer the heat to the coolant. The heated coolant is pumped to the intercooler system's auxiliary radiator where it is cooled down again.Heated air in turbocharger outlet pipeTurbochargerBoost pressure sensor G31 and intake air temperature sensor 2 G299IntercoolerCooled charge airIntake manifold Heated coolant to intercooler radiator in front endCooled coolant from intercooler radiator in front end616_02527Intercooler coolant circulation systemThe coolant circulation system for the intercooler is driven by the continued coolant circulation pump V51. The turbocharger is also incorporated in that "low temperature" coolant circulation system. This coolant circulation system should be seen as independent. It is only connected to the expansion tank, see "System overview" on page 24. Isolation is by way of flow restrictors and a non-return valve. Because of that separation, temperature differences of up to 100 °C from the main cooling system can occur. The pump is operated by means of a PWM signal from the engine management ECU. The pump is always run at 100 %. The times at which it is switched on and off are calculated using a data map. The most important variables referred to are the engine load and the charge air temperature upstream and downstream of the turbocharger when the engine is running.Run-on function After the engine is switched off, after-heating effects can cause the coolant to boil under certain circumstances (if the car has been driven at top speed and/or up a long climb in high outside temperatures). After the engine is switched off, the pump therefore runs on for a certain time according to a data map stored on the engine management ECU. The data map is computed using a model which calculates the exhaust temperatures. That then serves as a measure for the turbocharger housing temperature. While the pump V51 is running, the electric radiator fan is operated at the same time.Continued coolant circulation pump V51The continued coolant circulation pump V51 is bolted onto the cylinder block below the intake manifold. Integrated in the pump is an electronic control circuit. This analyses the PWM signal from the engine management ECU, for example. The pump is also fully diagnosis-compatible. Communication with the engine management ECU for diagnostic purposes takes place via the PWM signal lead.TurbochargerThe pump carries out a self-diagnosis routine when in operation. If a fault is detected, the details are stored on the pump's control unit. The engine management ECU continues to cyclically check that the pump is actually running. This involves connecting the control signal to earth for 0.5 seconds every 10 seconds. If any faults are detected, the details are sent to the engine management ECU.Diagnosable faults Fault number 1 2 3 4 Description/Remarks Running dry 1 Pump mechanism jammed Pump overheating Minimum speed not reachedBleeder pipeIntercooler integrated in intake manifoldContinued coolant circulation pump V51Cooled coolant Heated coolantIntercooler coolant radiator616_05028Air intake and turbocharger systemsOverviewCompared with the EA111 engine series, the intake system for the EA211 series is on the forward-facing side. Because the fitted position of the engine is also different with the engine tilted backwards by 12°, it has been possible to position the air filter box directly on the engine. This has a favourable effect on the length of the air intake system and the preheating of the intake air. An air/coolant heat exchanger integrated in the intake manifold module cools the heated intake air.Air filter box mounted directly on engine Heated air in turbocharger outlet pipeBoost pressure sensor G31 and intake air temperature sensor 2 G299Throttle valve module J338Intake manifold module with integrated intercooler616_027Intake manifold module with integrated intercooler The intercooler on the EA211 engine series is integrated in the injection-moulded plastic intake manifold. The advantage of this is that the relatively small volume of air in the entire charge air tract can be relatively quickly compressed. Very rapid pressure generation and very responsive engine performance are the results. The distance travelled by the charge air from the impeller to the intake manifold module through the plastic intake pipe (turbocharger outlet pipe) is also very short.Intake manifold pressure sensor G71 Intake air temperature sensor 1 G42Throttle valve module J338Fuel pressure sensor G247Intake manifold moduleIntercooler616_026 29TurbochargerOn the EA211 engine series, the exhaust manifold is integrated in the cylinder head and provided with its own coolant jacket. By using this design concept, it has been possible to make use of very lightweight mono-scroll turbochargers. Mono-scroll turbochargers have only one inlet helix which directs the exhaust to the turbine rotor. The significant advantage is their simplicity of design, which makes mono-scroll turbochargers especially light and economical.Intake manifold from air filter Turbocharger outlet pipeNon-return valve for in-feed from crankcase venting systemWastegate actuator V465WastegateConnecting flange to cylinder headWastegate actuating lever616_041Reference For more information on the design and function of the wastegate actuator V465, refer to Self-study Programme 606 "Audi 1.8 and 2.0l TFSI EA888 Series Engines (2nd Generation)".30Oil supply and coolingTo supply the turbocharger shaft with oil for lubrication, the turbocharger is incorporated in the oil circulation system. At high engine speeds, the blow-by gas from the crankcase venting system is fed back into the intake system upstream of the impeller. The connection for this is on the turbocharger, see Figure 616_017 on page 13. To provide for adequate cooling, the turbocharger is connected to the coolant circulation system. An electric coolant pump, the continued coolant circulation pump V51, pumps the coolant for both the intercooler and the turbocharger to the coolant radiator in the front end, see "Intercooler coolant circulation system" on page 28.Oil flowIn-feed from crankcase venting systemCoolant returnCoolant flowOil returnOil flow616_04931Cylinder on demand (cylinder shut-down system)IntroductionThe 103 kW version of the 1.4l TFSI engine benefits from a selective cylinder shut-down feature. When the system is activated, cylinders 2 and 3 are shut down. This reduces emissions and lowers fuel consumption. Modern petrol engines are generally run in the low power band. Under those conditions, the throttle losses are high because the throttle is only slightly open. That diminishes the efficiency and negatively affects the specific fuel consumption. An unthrottled 2-cylinder engine running at higher power has a more economical specific fuel consumption than a throttled 4-cylinder engine – a fundamental argument in favour of cylinder shut-down capability. The essential challenge for a cylinder shut-down facility was, therefore, that the inlet and exhaust valves on the cylinders to be shut down have to remain closed. Otherwise too much air would get into the exhaust system and the engine would cool down too quickly. Shutting down two cylinders would also make the 4-cylinder engine run less smoothly because of the lower firing frequency. In addition, the shut-down and reactivation of the cylinders needed to function as smoothly as possible (avoidance of abrupt load changes).Exhaust cam adjustment actuatorInlet cam adjustment actuatorSliding cam sleeve616_028Cylinder with shut-down capability Cylinder without shut-down capability32Development aims• Reduction of consumption in MVEG cycle (MVEG = Motor Vehicle Emission Group) and a perceptible lowering of fuel consumption for the customer at moderate speeds in the NEDC cycle (NEDC = New European Driving Cycle) by 10 to 20 %: • Around 8 g CO2/km • Up to 24 g CO2/km with start/stop system • Widest possible power band in 2-cylinder mode • Highest possible constant speed (above 140 kph) in 2-cylinder mode • No loss of passenger comfort in 2-cylinder modeMethod of operationCylinder shut-down is effected by the AVS variable valve timing technology developed by Audi. In accordance with the firing order, it is always cylinders 2 and 3 that are shut down. When the cylinders are shut down, the inlet and exhaust valves on those cylinders remain closed. The fuel injectors and ignition for those cylinders are also deactivated while the cylinders are inoperative. Changeover to 2-cylinder mode and back to 4-cylinder mode has to be as inobtrusive as possible, i.e. imperceptible to the vehicle's occupants. To avoid torque fluctuations during changeover, the pressure in the intake manifold is reduced to a low level. During cylinder charging, the firing point is retarded in response to the cylinder charge so as to remain torque-neutral. When the required charge is reached, first the exhaust valves and then the inlet valves of cylinders 2 and 3 are disabled. After replacement of the last charge, no further fuel injection takes place so that only intake air is trapped inside the cylinder. The intake air trapped inside the cylinder results in lower compression pressures in the combustion chamber during the next compression phase, which makes the changeovers smoother. In the two active cylinders, 1 and 4, the efficiency level increases because they are operating at higher loads. The internal friction relative to engine speed remains more or less constant while the effective power output rises. Running at lower levels of intake throttle produces lower charge replacement losses, better combustion and lower cylinder-wall heat losses. Reactivation of cylinders 2 and 3 takes place in the same order as for shut-down. First of all the exhaust valves are brought back into operation and then the inlet valves, thus releasing the trapped intake air in the cylinder into the exhaust system. The resulting leaner exhaust is counterbalanced by fuel injection into cylinders 1 and 4. That allows the oxygen-concentration control system to continue operating as normal.Indication on instrument clusterThe engine operating mode is indicated to the driver on the instrument cluster display. When the relevant menu is opened, "2-cylinder mode" is displayed as appropriate. The illustration shows the instrument cluster indicating the cylinder mode on the Audi A3 '13.2-cylinder mode616_07233Operating range of cylinder shut-downCylinder shut-down takes place within an area of the engine data map that is frequently used according to the average customer driving pattern. The lower engine speed limit was set at 1250 rpm because below that rev band cylinder shut-down causes the engine to run too unevenly. The upper limit was set at 4000 rpm in order to keep the actuation forces at a moderate level. The cylinder shut-down band starts in third gear at about 30 kph; it ends in fifth and sixth gears at around 130 kph. The possible torque in shut-down mode has been configured for an upper limit of between 75 and 100 Nm depending on engine speed. At higher torques the optimum consumption is no longer achieved due to the knock limits and ignition timing shifts in shut-down mode; accordingly, all four cylinders are enabled. To fully exploit the fuel-efficiency potential, cylinder shut-down is activated not only in the medium power band but also when the engine is overrunning. Due to the lower braking forces, the overrunning phases, during which fuel injection is inactive, are significantly longer. As soon as the driver operates the brake pedal, shut-down mode is terminated so that all four cylinders assist braking in overrunning mode. When coasting downhill cylinder shut-down is also disabled because the full engine braking effect is generally desirable in such situations. The information as to whether the car is coasting downhill is communicated to the engine management ECU via the CAN data bus. The signal concerned is provided by the ABS control unit J104 (based on wheel speed and vehicle inclination).Fuel economy with active cylinder shut-downKey: Fuel economy in % Torque [Nm]0 5 10 15 20 256th gear5th gear 4th gear110Speed Torque3rd gear616_061Engine speed [rpm]Cam adjustment actuatorsFor each cylinder that can be shut down, there is one actuator for the exhaust cams and one for the inlet cams on the cylinder head cover. As distinct from the AVS actuators previously used by Audi, which involved a separate actuator for each direction of movement, in this case both actuators are incorporated in a single unit. The design is similar to the individual actuators on other engines with AVS variable valve timing. A total of four actuators is fitted: • • • • Intake cam adjuster for cylinder 2 N583 Exhaust cam adjuster for cylinder 2 N587 Intake cam adjuster for cylinder 3 N591 Exhaust cam adjuster for cylinder 3 N595Electrical connection Solenoid 1 Solenoid 2Permanent magnet 1Permanent magnet 2 Guide tubeMetal pin 1 (actuated)Metal pin 2 (not actuated)616_03034Function(illustrated by cylinder 2, intake side)2-cylinder modeOperating the relevant cam adjustment actuator causes its metal pin to engage in the slot in the sliding cam sleeve. That slides the cam sleeve in axial direction along the spline on the camshaft as the camshaft rotates and locks the cam sleeve in that position. The roller-lever cam follower then runs on a "zero-lift cam". That cam has no raised lobe so that the valve concerned no longer moves in and out. All valves on the cylinder that is shut down stop moving. After the cam sleeve concerned has been successfully moved, the cam profile moves the extended metal pin of the actuator back to its initial position where it is held in place by the magnetic force until next operated. Sliding the metal pin back into the actuator solenoid induces a voltage. That serves as the feedback signal for the engine management ECU that changeover has been successfully completed. The illustrations show the cylinder shut-down function on cylinder 2 on the intake side.4-cylinder modeIn this operating mode, cylinder shut-down is inactive. The sliding cam sleeves are in the position in which all valves are operated.e-media Animation illustrating cylinder shut-down616_029Cam sleeve is moved over to zero-lift cam 2-cylinder modeCam sleeve is moved back to working cam 4-cylinder modeReference More information on the design and function of the Audi valvelift system (AVS) can be found in Self-study Programme 411 "Audi 2.8l and 3.2l FSI Engine with Audi valvelift system".35Vibration and noise reduction measuresThe engine's generally low vibration characteristics are achieved from the outset by its fundamental design involving rigid construction, lightweight crankshaft drive gear and transverse orientation in the vehicle.Initial situation The greatest challenges are shut-down and reactivation of the cylinders and the engine's vibration characteristics and noise in 2-cylinder mode. Although shutting down cylinders 2 and 3 maintains an even firing interval, the fact remains that in 2-cylinder mode only one cylinder fires per crankshaft revolution, whereas in 4-cylinder mode two cylinders fire per revolution. Without any additional measures, that would lead to greater vibration and a noisier engine.Measures as illustrated by Audi A3 '13 SportbackModified dual-mass flywheelExhaust system with additional centre silencer616_083Upper metalastic mountingEngine/gearbox mountings As regards engine and gearbox mountings, the front engine mountings have been carried over from the engine without cylinder shut-down. The vibrations that occur in 2-cylinder mode are largely minimised by the softer metalastic mountings on the engine subframe.Lower metalastic mounting616_08536Dual-mass flywheel The dual-mass flywheel is designed to offer optimum insulation both in 2-cylinder and 4-cylinder mode. Rotational vibration/ engine unevenness should not be transmitted to the rest of the drive train. For that reason, the springs between the engine and gearbox-side flywheel masses have been dimensioned specifically to fit the requirements. The resonance speed of the flywheel's sprung mass system is significantly below the engine's idling speed, i.e. the range in which the vehicle can be driven. With a dual-mass flywheel designed purely for use on a normal 4-cylinder engine without cylinder shut-down, the resonance speed1) would be substantially within the engine's drivable range. That would induce very high levels of resonant vibration by the flywheel. For that reason, the spring characteristic has been made as soft as possible for two-cylinder mode. This has shifted the resonance speed in 2-cylinder mode to below engine idling speed.1) he resonance speed occurs when the excitation frequency is the T same as the natural frequency. That means that the excitation has an accelerating effect on the direction of movement at any particular moment and the vibration is increasingly amplified.616_084Exhaust system In order to reduce the large difference in exhaust system pulsation between 2-cylinder and 4-cylinder modes, the front and rear silencers in the exhaust system have differently dimensioned resonators and volumes. As well as that, the pipe lengths have been specially adapted and an additional centre silencer fitted. For more information, refer to the section on exhaust systems in "1.4l TFSI engine with cylinder shut-down in Audi A3 '13" on page 43.Deployment conditions for 2-cylinder modeFor the engine to actually switch to 2-cylinder mode, the following conditions must be met: • Engine speed must be above idling (for reasons of engine smoothness). • Engine speed must be roughly in the range of 1250 - 4000 rpm. • The oil temperature is must be at least 50 °C. • The coolant temperature must be at least 30 °C. • The gear box must be in 3rd gear or higher. The system can also be activated with the automatic transmission in S-mode and Audi drive select set to "dynamic". Driving profile recognition The cylinder shut-down system also has a control algorithm that monitors use of the accelerator, brake pedal and steering wheel by the driver. If the system detects an uneven pattern in that data, it does not activate cylinder shut-down in certain situations because deactivating the cylinders for only a few seconds would tend to increase rather than lower fuel consumption.37Shut-down and reactivation sequenceShut-down sequenceThe complete shut-down sequence takes place within the course of one camshaft revolution. So that the driver notices as little as possible of what is happening, various measures must be employed within a matter of milliseconds to ensure that no abrupt load changes occur during shut-down.As an oxygen concentration of lambda 1 must be maintained at all times and, for example, because changes in the intake system require more time than changes in the ignition system, the order in which the measures are applied is decisive.616_029aPhase/Action Phase 1 Throttle valve adjustmentMode 4-cylinder modeDescription So that cylinders 1 and 4 are supplied with sufficient air after cylinders 2 and 3 have been shut down, the throttle is opened wider. All of the cylinders together then receive about twice as much air as required for the current torque demand in 2-cylinder mode. As all cylinders are still active, the following operating cycle would produce a significant increase in torque. To prevent that, the ignition timing is progressively retarded as the air volume increases, thereby diminishing efficiency. The torque then remains constant.Ignition timing adjustment cylinders 1 to 4Phase 2 Exhaust discharge2-cylinder modeAfter the last power stroke, the exhaust is expelled.Once the exhaust has been expelled, the engine management ECU operates the exhaust cam adjuster by applying a short earth signal pulse. The sliding cam sleeves are moved across and the roller-lever cam followers run on the zero-lift cams. The exhaust valves are no longer operated. Phase 3 Injection, ignition Cylinders 2 and 3 Phase 4 Inlet valves Cylinders 2 and 3 2-cylinder mode Fuel injection and ignition are deactivated.2-cylinder modeIntake air is drawn in again. The trapped air acts like spring. The force required to compress it aids subsequent downward movement of the piston.Once the intake air has been drawn in, the engine management ECU operates the inlet cam adjuster by applying a short earth signal pulse. The sliding cam sleeves are moved across and the roller-lever cam followers run on the zerolift cams. The inlet valves are no longer operated. Phase 5 Ignition timing adjustment Cylinders 1 and 4 2-cylinder mode The ignition timing for cylinders 1 and 4 is advanced to obtain optimum efficiency.38Reactivation sequenceAbrupt load changes that would be perceived as obtrusive by the driver must be avoided in the reactivation sequence as well. Thus, once again, various measures are employed by the engine mechanicals and engine management to prevent abrupt torque changes.616_029bPhase/Action Phase 1 Exhaust valves Cylinders 2 and 3 Phase 2 Exhaust valves Cylinders 1 and 4Mode 2-cylinder modeDescription The engine management ECU operates the exhaust cam adjuster by applying a short earth signal pulse. The sliding cam sleeves are moved across and the roller-lever cam followers run on the normal-lift cams again. The exhaust valves are operated and the trapped intake air expelled. The expelled intake air would produce a leaner exhaust mixture so that the oxygen concentration would rise above lambda 1. As the catalytic converter requires an oxygen concentration of lambda 1 to function most effectively, the injection volume in cylinders 1 and 4 is increased to produce a level of lambda 1 at the catalytic converter. The engine management ECU operates the inlet cam adjuster by applying a short earth signal pulse. The sliding cam sleeves are moved across and the roller-lever cam followers run on the normal-lift cams again. The inlet valves are operated and intake air is drawn in. As all cylinders are active again and the throttle is still open wide, the following power stroke would produce a significant increase in torque. To prevent that, the ignition timing is progressively retarded, thereby diminishing efficiency. The torque then remains constant. As all cylinders are now being supplied with air, the throttle is closed more to prevent an abrupt increase in torque.2-cylinder modePhase 3 Intake valves Cylinders 2 and 3 Phase 4 Ignition timing adjustment cylinders 1 to 4 Phase 5 Throttle valve adjustment Cylinders 1 and 44-cylinder mode4-cylinder mode4-cylinder modeIgnition timing adjustment cylinders 1 to 4The ignition timing for all cylinders is advanced to obtain optimum efficiency.39Function diagram (Audi A3 ’13)Powertrain CANKey: G28 Engine speed sensor G62 Coolant temperature sensor G266 Oil level/temperature sensor J104 J285 J533 J623 ABS control unit Instrument panel control unit Data bus diagnostic interface Engine management control unit N584 Intake cam adjuster A for cylinder 2 N585 Intake cam adjuster B for cylinder 2 N587 Exhaust cam adjuster for cylinder 2 N588 Exhaust cam adjuster A for cylinder 2 N589 Exhaust cam adjuster B for cylinder 2 N591 Intake cam adjuster for cylinder 3 N592 Intake cam adjuster A for cylinder 3 N593 Intake cam adjuster B for cylinder 3 N595 Exhaust cam adjuster for cylinder 3 N596 Exhaust cam adjuster A for cylinder 3 N597 Exhaust cam adjuster B for cylinder 3 P Q Spark plug connector Spark plugsN30 Fuel injector for cylinder 1 N31 Fuel injector for cylinder 2 N32 Fuel injector for cylinder 3 N33 Fuel injector for cylinder 4 N127 Ignition coil 2 with output stage N291 Ignition coil 3 with output stage N583 Intake cam adjuster for cylinder 240Suspension and steering CAN 616_044Comfort/convenience CANFuel systemOverviewThe maximum pressure in the combustion chambers has been increased to 200 bar. That pressure is generated by a latestgeneration high-pressure fuel pump made by Hitachi. Its operating pressure is between 100 bar minimum when the engine is idling and 200 bar at approx. 6000 rpm. The pressure limiting valve is designed to open at pressure peaks of over 230 bar and direct the fuel back to the intake side of the pump. The control concept of the new-design pump is now the same as the control concepts for other new engine designs such as the 3rd generation EA888 series. That control concept is as follows: if the power supply to the fuel pressure regulating valve N276 is cut off, no fuel is delivered to the high-pressure system. The engine cuts out.High-pressure injectorsState-of-the-art, 5-jet fuel injectors are supplied with fuel by a stainless-steel fuel rail. This enables extremely precise fuel injection with up