TECHNICAL DOCUMENTATION
SSP 623 Audi A3 Cabriolet 2014

This PDF is currently unavailable.
Read document text
Self Study Programme 623 For internal use onlyAudi A3 Cabriolet ’14Audi Service TrainingAudi A3 Cabriolet ’14Sporty, elegant and multi-faceted – introducing the new Audi A3 Cabriolet ’14. This compact four-seater impresses at first glance with its flowing lines and soft top. It is also at the top of its class technically – with systematic lightweight design, new engines, multi-faceted networking and high-performance assistance systems. The Audi A3 Cabriolet ’14 completes the A3 family. The new Audi A3 Cabriolet '14 has grown compared to the outgoing model – in length, wheelbase and width. Only its height has been reduced – to give the four-seat convertible a more elegant and sporty look on the road. The new Audi A3 Cabriolet ’14 has a soft top that is stretched over a lightweight magnesium-steel kinematic mechanism, and it complements the car's design perfectly. At the press of a button, the top opens or closes electro-hydraulically in less than 18 seconds, even while driving up to 50 kph. The fully automatic soft top has a glass rear window. A fully automatic acoustic top is available as an alternative; it has a thicker inner foam layer which reduces the already low interior noise level of the Audi A3 Cabriolet '14 even more. An active rollover protection system protects the occupants in case of a rollover accident. Elegantly drawn lines and clean surfaces also typify the interior design of the new Audi A3 Cabriolet '14. The optional lighting package includes, for the first time, a touch-sensitive switch for the reading lights. As in every Audi, workmanship quality is uncompromisingly high, and the car's controls are simple, intuitive and convenient. It offers enough space for four adults, and the seatbacks of the two rear seats can be folded down to create a wide through-load area. The steering wheel and seats are new designs, and the also new electro-mechanical parking brake is operated by a pushbutton on the centre console. All engines in the new Audi A3 Cabriolet '14 combine the technologies of direct injection, turbocharging and a start-stop-system. On average, the three engines offered at market launch have twelve percent better fuel economy than the engines in the outgoing model – and they do so while improving driving performance. The chassis of the new Audi A3 Cabriolet '14 impresses with sophisticated technology that delivers sporty handling, superior vehicle safety and a high level of comfort. Some of the components of the MacPherson front suspension are made of aluminum; the four-link rear suspension handles longitudinal and transverse forces separately. The power steering system features an efficient electromechanical drive. The ESC stability control system integrates an electronic limited slip differential – this makes handling even smoother and safer at the vehicle’s cornering limits while driving fast through curves. The brakes are powerful and durable.623_0012ContentsIntroductionIn brief ________________________________________________________________________________________________________________________________________________________ 4BodyBody structure/materials _ ___________________________________________________________________________________________________________________________________ 6 Body structure/reinforcements _____________________________________________________________________________________________________________________________ 8Convertible topVariable convertible top well _ _____________________________________________________________________________________________________________________________ 12 Convertible top box lid/service position __________________________________________________________________________________________________________________ 13 Convertible top frame ______________________________________________________________________________________________________________________________________ 14 Hydraulic unit _ _______________________________________________________________________________________________________________________________________________ 15Convertible top control systemInstallation locations of the convertible top control unit _ ______________________________________________________________________________________________ 16 Convertible top operation __________________________________________________________________________________________________________________________________ 18 Components of the convertible top control unit _________________________________________________________________________________________________________ 30 Emergency operation _______________________________________________________________________________________________________________________________________ 42 Data bus overview ___________________________________________________________________________________________________________________________________________ 45Occupant safetyComponents _________________________________________________________________________________________________________________________________________________ 46 System overview ____________________________________________________________________________________________________________________________________________ 48 Side airbag ___________________________________________________________________________________________________________________________________________________ 50 Electrical wiring loom for side airbag _____________________________________________________________________________________________________________________ 51 Rear side airbag crash sensor, driver side G256 _ ________________________________________________________________________________________________________ 51 Rollover protection _ ________________________________________________________________________________________________________________________________________ 52 Cassettes with anti-roll bars _______________________________________________________________________________________________________________________________ 53 Rollover protection trigger, driver side N646 and rollover protection trigger, passenger side N647 ______________________________________________ 53 Deployed rollover protection system N647 ______________________________________________________________________________________________________________ 54 Resetting a deployed anti-roll bar _________________________________________________________________________________________________________________________ 55 Diagnostics __________________________________________________________________________________________________________________________________________________ 55Engine/gearbox combinationsPetrol engines _______________________________________________________________________________________________________________________________________________ 56 Diesel engines _______________________________________________________________________________________________________________________________________________ 57SuspensionOverall concept _____________________________________________________________________________________________________________________________________________ 58 Overview _____________________________________________________________________________________________________________________________________________________ 59Electrical systemInstallation locations of control units ____________________________________________________________________________________________________________________ 60 Topology _____________________________________________________________________________________________________________________________________________________ 62Air conditioningIntroduction _________________________________________________________________________________________________________________________________________________ 64 Operation ____________________________________________________________________________________________________________________________________________________ 65InfotainmentSound system _______________________________________________________________________________________________________________________________________________ 68 Aerial system ________________________________________________________________________________________________________________________________________________ 70 Overview of versions ________________________________________________________________________________________________________________________________________ 72ServiceInspection and maintenance _ ______________________________________________________________________________________________________________________________ 74 Self Study Programmes ____________________________________________________________________________________________________________________________________ 75• The Self Study Programme teaches a basic knowledge of the design and mode of operation of new models, new automotive components or new technologies. It is not a Repair Manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. Content is not updated. For further information on maintenance and repair work, always refer to the current technical literature.!NoteReference3IntroductionIn briefDimensions623_002623_003!4Note The graphics and illustrations shown in this self study programme are basic representations and are given to help understand concepts.623_004Length in mm Width in mm Height in mm Track width, front in mm Track width, rear in mm Wheelbase in mm Trailer load in kg with brake at a gradient of 8 % Kerb weight in kg Max. gross weight in kg4421 17935) 1409 1555 1526 2595 18004) 14304) 1930Cabin width, front in mm Cabin width, rear in mm Headroom, front in mm Headroom, rear in mm Load sill height in mm Boot capacity in l Tank capacity in l Drag coefficient in cw1468 1203 1000 921 685 320 50 0.30Shoulder room width Elbow room width 3) Maximum headroom 4) with a 1.8l TFSI engine developing 132 kW at 250 Nm 5) excluding mirror1) 2)All dimensions are given in millimetres and refer to the unladen weight of the vehicle.5BodyBody structure/materialsThe body of the Audi A3 Cabriolet ’14 rigid and crash-safe body structure designed on the basis of the Audi A3 saloon. Thanks to Audi ultra-lightweight technology, convertible-specific elements such as the A post, front roof frame, rear bulkhead and the underbody are designed so they do not add weight to the A3 Cabriolet ’14. Including its special reinforcements, which deliver high torsional stiffness, the body-in-white weighs 30 kg less than the outgoing model.AttachmentsThe attachments, specifically the wings, doors, convertible top box lid, rear hatch and bumper cross-members, are of lightweight steel construction. The following components of the A3 Cabriolet ’14 are made from aluminium: • Bonnet • Front bumper cross-member6Key:623_106Ultrahigh strength steel (hot-formed) Advanced high strength steel High strength steel Low strength steel Sheet aluminium Aluminium section7Body structure/reinforcementsA post reinforcementThe A3 Cabriolet ’14 affords a high level of safety in the event of a rollover accident thanks to its extremely stiff A post structure, which comprises an inner plate and a reinforcement tube. The inner plate is made from modern high-tensile steel and the reinforcement tube from ultra-high-strength thermoformed steel.Reinforcing tubeInner A post623_107Lower rail / sill / seat cross-member reinforcementsVarious additional reinforcements are used to ensure that the body structure meets the high convertible-specific strength requirements in the lower rail/sill and the B post areas. To provide better side impact protection, the seat cross-member located between both B posts is made from ultra-high-strength thermoformed steel.Seat cross-memberB post with reinforcementsReinforcement Side member/sill623_1088Rear bulkheadAdditional strengthening is provided by the rear bulkhead, which is rigidly connected to the car body. High-strength sheet steel is used to achieve extremely high rigidity in crash-relevant areas, such as the rollover protection system mounting. This not only provides better safety for the car occupants; it also increases the stiffness of the occupant cell significantly.Rollover protection system mountingRear bulkhead623_109Door side impact reinforcementThe door side impact protection is specially adapted for the A3 Cabriolet ’14; during a collision ,it absorbs the impact energy and dissipates it to the body side structure.Side impact protection623_110Additional reinforcements9Convertible topAs with the outgoing generation, the new Audi A3 Cabriolet ’14 features a classical soft top with k fold system. The substructure comprises a mix of magnesium, aluminium and steel. At the press of a button, the top opens or closes electro-hydraulically in less than 18 seconds, even while driving up to 50 kph. In the opened state, the convertible top – folded into three layers – is stowed in a well. Excellent thermal insulation and a heated glass rear window mean the new Audi A3 Cabriolet ’14 is also suitable for winter use. The soft top is made from rugged materials and optionally available in a deluxe version (acoustic convertible top). The complete convertible top weighs approximately 51 kg.Roof bowRoof bowThe roof bows contain grooves in which the convertible top cover is attached by welting. For removal and installation, the convertible top cover can be pulled in and out at the sides. The headliner clips onto the roof bows.Convertible top cover with sound insulating foamConvertible top cover welting Headliner retaining stripRoof bowInterior lining623_11110Convertible top fabricThe convertible top cover comprises a tarpaulin with layers of insulation (acoustic insulating foam). The acoustic convertible top provides superior sound and thermal insulation thanks to an acoustic insulating foam of adapted density and thickness (10mm instead of 7 mm in the basic convertible top). The convertible top tarpaulin itself has a three-layered structure. The outer layer is made of an acrylic nitrile fabric, the middle layer of butyl rubber (acoustic convertible top) or chloroprene rubber (basic convertible top) and the inner layer of polyester fabric. The tarpaulin is manufactured from a middle panel and two side sections.Convertible top tarpaulin Sound insulating foamInterior lining623_112Rear window The glass rear window is made of 3.15 mm toughened safety glass and is electrically heated. It is bonded to the convertible top cover. AM aerial2Tensioning strut The tensioning strut is seated on the convertible top box lid and locks in the OTDC position so that the hydraulic system can depressurise after closing.623_113!Note The integrated glass rear window cannot be replaced individually.11Variable convertible top wellThe convertible top of the A3 Cabriolet ’14 can only be opened when the convertible top tray is in the lowered position. The convertible top well can be lowered manually by pulling the handle. The variable convertible top well can be raised when the convertible top is closed, thereby providing additional load capacity in the boot.WindbreakThe windbreak reduces draughts inside the vehicle for greater comfort when driving with the soft top open. The windbreak is engaged into the side trims behind the front seats and then moved into the upright position. When not in use, the windbreak is folded away and stowed in a storage bag in the boot.!12Note The windbreak can be left on the car when the convertible top is closed.Convertible top box lid/service positionThe convertible top box lid is a lightweight steel construction and stops the open convertible top from becoming dirty. It is opened and closed by two hydraulic cylinders seated on the left and right toggle levers (hinges). For assembly work on the convertible top, the convertible top and/ or the convertible top box lid must be moved into the service position (limit position). To prevent unwanted closing of the lid, both toggle levers (hinges) must be pushed towards the tensioning strut at the upper pivot point as far as the stop. A tensioning strap (T10038) and two hooks (T4036) are engaged into the convertible top edge centrally at the front and back and hold the convertible top in the assembly position.T 10038 T 40306 T 40306623_114Convertible top well, upper positionConvertible top, lower position623_11513Convertible top frameThe convertible top frame to bolted to the car body, with a main bearing attached to a mounting plate on the left and right. Unlike in the outgoing model generation, the position of the retaining plates is now defined by the reference point system (RPS) of the car body and cannot be changed.Roof bow tensioning strap Front roof bow Convertible top locking motor Convertible top lock Roof bow 4 Roof bow 1 Roof bow 2 Roof bow 3Roof bows 1-4 are made from extruded aluminium sections. The front roof bow, on the other hand, is made from high-grade magnesium on account of its complex design. By using these different materials, the convertible top frame meets high standards for stability and strength.Front roof rodHydraulic cylinder for tensioning strut AM aerial2 Tensioning strut Rear roof rodMain side bar Hydraulic cylinder Convertible top box lid Rear windowHydraulic cylinder for tensioning strutMain bearing with hydraulic cylinder for convertible topHydraulic pump Hydraulic cylinder Convertible top box lid623_116Main bearingThe convertible top can be removed and installed using the two spacers T40307, which are inserted into the left and right main bearings from above and remain inside the main bearings during the entire time the convertible top is removed. When the convertible top is removed, the spacers replace the missing stop buffers on the car body and thereby prevent damage to the convertible top cover and convertible top frame while the convertible top is in storage or transit.T40307!14Note Please follow the instructions given in the Workshop Manual during all work on the convertible top.Hydraulic unitThe hydraulic unit consists of the electric motor, the valve block (including pump and valves) and the oil tank. Plastic-sheathed flexible metal spiral hoses connect the hydraulic cylinders to the hydraulic unit. Relays 1 and 2 are clipped onto the hydraulic unit and control the operating current for clockwise and anticlockwise operation of the pump. During the convertible top raising or lowering sequence, the pump runs and valves 1-3 control the flow of fluid according to the required sequence of movements. The direction of rotation of the pump only needs to be reversed to move the tensioning strut into position when raising the convertible top. Pump pressure is limited to max. 180 bar by pressure-limiting valves. When the system is at rest, the hydraulic fluid can flow back from the hydraulic cylinders to the fluid reservoir unpressurised, allowing the convertible top to be emergency-operated.Plastic-sheathed flexible metal spiral hose Valve blockElectric motorPower operated convertible top valve -2- N341 Power operated convertible top valve -1- N272 Power operated convertible top valve -3- N342 Oil filler screwOil reservoirRelay 2 J588623_118Relay 1 J321Bleeding the systemIf repair work has been performed on the hydraulic system, no bleeding is required. The hydraulic system is bled automatically during operation.Hydraulic cylinderDouble-acting hydraulic cylinders are used. They can be activated from both sides according to the movement sequence and are birdirectional.Solenoid valveThe hydraulic system is fitted with 3/2-way valves (valves with 3 connections and 2 switch positions) which are operated electromagnetically and reset by spring force. Oil flows out of the cylinders and into the tank when the valves are de-energised, and from the pump to the cylinders when the valves are energised. The valves are activated by the control unit for 5 minutes. The convertible top can be emergency-operated directly after the valves have been switched off. When the valves are de-energised, the hydraulic system depressurises and the convertible top collapses completely.15Convertible top control systemInstallation locations of the convertible top control unitThe component parts of the system are summarised on the following two pages.F412 F294 F295 V223F411J285F13716Key E137 F171 F202 F293 F294 F295 F404 F407 F408 F411 F412 F517 F519 F520 Convertible top operating switch Convertible top stowed switch Convertible top front switch Convertible top box lid latch unlocked switch Convertible top lock open switch Convertible top lock closed switch Convertible top box lid latch engaged switch Convertible top box lid up switch Tensioning strut up switch Convertible top lock closed switch, left Convertible top lock closed switch, right Tensioning strut down switch Convertible top box lid closed switch Convertible top well down switch J256 J285 J321 J588 N272 N341 N342 V118 V222 V223 Convertible top operation control unit Control unit in dash panel insert (diagram showing convertible top status) Hydraulic pump relay 1, convertible top operation Hydraulic pump relay 2, convertible top operation Power operated convertible top valve 1 Power operated convertible top valve 2 Power operated convertible top valve 3 Convertible top operation hydraulic pump Convertible top box lid latch motor Convertible top locking motorF520 F519 F404 F293 V222J256 N341 N272 N342F171 F202 F517 F408 F407J588V118623_023J32117Convertible top operationThe convertible top on the Audi A3 Cabriolet ’14 is opened and closed by an electro-hydraulic system. In contrast to the outgoing model, the Audi A3 Cabriolet ’14 has a convertible top box lid. The convertible top box is completely covered by the convertible top box lid. Objects deposited on the convertible top box lid or in the convertible top box can damage the vehicle during convertible top operation. The convertible top is only available as a fully automatic convertible top. It is also optionally available as an acoustic convertible top. The acoustic convertible top offers better thermal and sound insulation than the standard convertible top.Service position of convertible top and convertible top box lidThe hydraulic system is depressurised approx. 5 minutes after the last actuation. The convertible top can then collapse completely and the convertible top box lid can close. When carrying out work on the convertible top system, please note that moving parts can cause injury. This is why the hydraulic pressure must be relieved and the convertible top moved into the service position before carrying out work on the convertible top. For further information, refer to page 13 "Convertible top box lid/service position" and the Workshop Manual.Basics of convertible top operating switch E137The convertible top opening cycle is started by pulling the convertible top operating switch E137. To open the convertible top completely, the switch must be kept pulled until the opening cycle is complete. When the switch is released, the convertible top cycle stops instantaneously. If the switch is pulled again, the convertible top continues to open. If the switch is pressed, the convertible top closes. The switch must also be kept actuated (pressed) during the closing cycle. If the convertible top is closed and the switch for opening the convertible top is pulled and then released again, the side windows will lower to a certain level. The convertible top cycle will not start. If the button is now kept pressed for the next 5 seconds, the side windows closes again. this function is unavailable due to legal restrictions in some countries, including the USA.623_024Convertible top operating switch E137Graphic displays for convertible top operation in instrument panel J285The Audi A3 Cabriolet ’14 uses a different method to indicate convertible top operation. A separate convertible top operation warning lamp is no longer used. Instead, the operation of the convertible top is now indicated graphically. The displays are monochrome or colour depending on dash panel insert version.As soon as the convertible top starts to open or close, a graphic display appears in the dash panel insert J285 showing the vehicle together with the convertible top.A curved arrow over the convertible top indicates the direction of the convertible top. If the arrow tip is pointing back, the convertible top is opening. If the arrow tip is pointing forward, the convertible top is closing.Convertible top opening cycle623_025Convertible top opening cycle623_02618If no arrow is displayed over the convertible top, the convertible top cycle has been initiated but aborted. The convertible top is therefore currently in an intermediate position.Convertible top cycle aborted, intermediate position623_027Convertible top cycle aborted, intermediate position623_028If the convertible top cycle has been completed, the status of the convertible top (opened or closed) is indicated for approx. 2 seconds. An audible signal sounds at the same time.Convertible top cycle completed, convertible top closed623_029Convertible top cycle completed, convertible top closed623_030Convertible top cycle completed, convertible top open623_051Convertible top cycle completed, convertible top open623_05219If a convertible top operation is not possible, this is indicated audibly and visually in the dash panel insert. A warning is given and nine messages are displayed.The warning is given if the convertible top is in an intermediate position, and if the event memory contains an entry and the vehicle is travelling faster than 5 kph.Warnings are indicated via the colour dash panel insert as follows:Triangle with exclamation mark in the driver information and warning lamps tab Yellow vehicle-with-convertible-top icon in the status lineConvertible top: malfunction!Displayed textyou can continue driving (limited functionality). See owner's manualYellow central warning lamp623_031Warnings are indicated via the monochrome dash panel insert as follows:Exclamation mark in driver information tab and warning lamps tab Vehicle convertible top icon in the status lineConvertible top: malfunction!Displayed textyou can continue driving (limited functionality). See owner's manualYellow central warning lamp623_03220Other reasons why a convertible top operation is not possible are displayed as messages.Display of messages in the dash panel insert:• The yellow warning lamp is NOT activated when messages are displayed. • Messages are indicated by a white vehicle-with-convertible-top icon in the status line in both the colour and monochrome dash panel inserts. • Message texts are NOT included in the driver information and warning lamps tab. If the convertible top is in a limit position (open or closed) and a convertible top cycle is initiated in the limit stop direction, no actions are initiated and no messages are displayed.To activate messages, the following conditions must be met: The boot lid is open and the convertible top operating switch is actuated.Convertible top: Please close boot lid623_033The convertible top well is in the upper position and the convertible top operating switch is actuated in the "open" direction.Convertible top: Please lower convertible top well623_034The convertible top is in a limit position (open or closed), the vehicle is travelling faster than 50 kph and the convertible top operating switch is actuated.Convertible top: no operation possible. Speed too high623_03521A convertible top cycle is currently active and the vehicle's speed increases to over 50 kph or the convertible top is in an intermediate position and the vehicle's speed exceeds 50 kph Convertible top: not in limit position. Speed too high623_036The ambient temperature is below -15 °C, the convertible top is closed and the convertible top operating switch is actuated in the "open" direction. An open convertible top can also be closed at temperatures below -15°C. Convertible top: no operation possible. Ambient temperature too low623_037The convertible top operation control unit has registered a static event and the switch is actuated.Convertible top: no operation possible623_03822The car’s battery voltage has dropped below a certain value. The ignition is "on" but the engine is "off" and the convertible top operating switch is actuated.Convertible top: no operation possible. Engine must be running623_039The overload protection is active and the convertible top operating switch is actuated.Convertible top: no operation possible623_040The convertible top operation control unit has registered a static event, the limit position (open or closed) has been reached and the actuated convertible top operating switch is released.Convertible top: malfunction! You can continue driving623_04123Convertible top opening sequenceTo be able to open the convertible top, the following conditions must be met: • The vehicle must not be travelling faster than 50 kph • The function must be switched on • The ambient temperature must be above -15 °C • The convertible top well must be in the lower position • The boot lid must be closed • The battery voltage must be sufficientInitial situation: the convertible top is closed Assuming that all conditions are met and the convertible top operating switch E137 is kept pulled, the side windows initially open to a certain level.623_043623_042Convertible top operating switch E137A graphic display then appears in the dash panel insert J285 showing the vehicle with convertible top and a curved arrow. The arrow tip is pointing back.Convertible top opening cycle623_044Convertible top opening cycle623_045At this time the boot lid handle release button E234 is not functional. Therefore, the boot lid cannot be opened.If the rear window heater is on, it is switched off. The rear window heater can only be switched on if the convertible top is fully closed.24Next, the catch hooks in the upper part of the lock in the window frame area move upwards. At the same time, the tensioning strut begins to move into the upright position.623_046At the same time, the convertible top box lid latch motor V222 opens the convertible top box lid. The tensioning strut moves into the upright position. The convertible top box lid opens fully.623_047The convertible top retracts and folds down into the convertible top well. Meanwhile, the catch hooks close again.623_048After that, the convertible top box lid closes and the convertible top box lid latch motor locks the convertible top box lid.An acoustic signal and a graphic display in the dash panel insert J285 indicate that the convertible top cycle is complete and the convertible top is fully open.623_049Convertible top cycle completed, convertible top open623_051Convertible top cycle completed, convertible top open623_052Finally, the side windows move up all the way and the boot lid can again be opened.623_050 25Convertible top closing sequenceTo be able to close the convertible top, the following conditions must be met: • The vehicle must not be travelling faster than 50 kph • The function must be switched on • The boot lid must be closed • The battery voltage must be sufficientInitial situation: the convertible top is open The convertible top operating switch E137 is kept pressed. First, the side windows open to a certain value.623_046a623_042Convertible top operating switch E137A graphic display then appears in the dash panel insert J285 showing the vehicle with convertible top and a curved arrow. The arrow tip is pointing forward.Convertible top closing cycle623_053Convertible top closing cycle623_054At this time the boot lid handle release button E234 is not functional. Therefore, the boot lid cannot be opened.26The convertible top box lid latch motor V222 unlocks the convertible top box lid and the convertible top box lid opens fully.623_046bThe convertible top lifts up out of the convertible top box and the catch hooks in the upper part of the convertible top lock open.623_046cThe tensioning strut moves into the upper position and the convertible top box lid closes fully. The convertible top box lid latch motor locks the convertible top box lid.623_046dThe convertible top continues to run until it settles on top of the window frame. At the same time, the tensioning strut moves down. The catch hooks then lock the convertible top.623_046eAn acoustic signal and the graphic display in the dash panel insert J285 indicate that the convertible top cycle is complete and the convertible top is fully closed.Convertible top cycle completed, convertible top closed623_055Convertible top cycle completed, convertible top closed623_056If the convertible top operating switch E137 is kept pressed, the side windows close. This function is unavailable in some countries due to legal restrictions.The boot lid can be opened again and the rear window heater can be switched on again.27Opening the convertible top with the car key via the lock cylinder on the driver's door.The convertible top can also be opened using the car key. Before this can be done, the following conditions must be met: • The vehicle must be travelling at 0 kph • The boot lid must be closed • The battery voltage must be sufficient • The convertible top well must be in the lower position • The ambient temperature must be above -15 °CTo open the convertible top, first unlock the vehicle with the car key. Then insert the car key into the lock cylinder on the driver's door and turn it in the "open" direction. If the car key in now turned in the "open" direction again within 2 seconds and held in this position, the convertible top cycle will start. The car key must be kept held in the "open" position during the convertible top cycle. When the car key is released, the convertible top cycle will stop instantaneously. To resume the convertible top opening cycle, the car key must again be turned in the "open" direction and held in this position. If the car key is turned in the "close" direction and held in this position, the convertible top will close again.623_057Closing the convertible top with the car key via the lock cylinder on the driver's door.The convertible top can also be closed using the car key. Before this can be done, the following conditions must be met:• The vehicle must be travelling at 0 kph • The boot lid must be closed • The battery voltage must be sufficientInsert the car key into the lock cylinder on the driver's door and turn it in the "close" direction. If the car key in now turned in the "close" direction again within 2 seconds and held in this position, the convertible top cycle will start. The car key must be kept held in the "close" position during the convertible top cycle. When the car key is released, the convertible top cycle will stop instantaneously. To resume the convertible top cycle, the car key must again be turned in the "close" direction and held in this position. If the car key is turned in the "open" direction and held in this position, the convertible top will open again.623_058!28Note If the convertible top is actuated via the car key, the convertible top will start after a delay.Operating the convertible top while drivingThe convertible top can be opened or closed using the convertible top operating switch E137 up to a speed of 50 kph. If the vehicle's speed increases to over 50 kph during the convertible top cycle, the driver will be alerted audibly and visually. The convertible top cycle is stopped and the convertible top comes to a standstill in its current position. The convertible top cycle cannot be resumed until the vehcile's speed has dropped to 50 kph or less. To do this, the convertible top operating switch must be kept pressed.Convertible top: not in limit position. Speed too highMessage text623_059A convertible top cycle cannot be initiated if the vehicle is travelling at a speed of over 50 kph. In this case too, the driver is alerted by audible and visual warnings.Convertible top: no operation possible. Speed too highMessage text623_06029Components of the convertible top control unitConvertible top operating switch E137The convertible top operating switch E137 is available in two versions: firstly in a large version and secondly in a small version. The small version is installed if the vehicle is equipped with Hill Start Assist and AUTO HOLD button E540. In this case, the Hill Start Assist switch is installed in place of the small convertible top operating switch. Thr functions of the small and large switches are identical. The switch is installed in the centre console.623_061623_062Convertible top operating switch E137AUTO HOLD button E540 Convertible top operating switch E137Hall sensorControlled operation of the convertible top is only possible if the convertible top operation control unit J256 receives information from the sensors and switches during every phase of the convertible top cycle. The sensors and switches indicate the current position of certain parts of the convertible top system to the convertible top operation control unit J256. The convertible top operation control unit J256 uses this information to control the actuators and, thus, the operation of the convertible top. The following Hall sensors in the Audi A3 Cabriolet ’14 react to the fields generated by permanent magnets: • • • • • • • Convertible top well down switch F520 Convertible top lock closed switch, left F411 Convertible top lock closed switch, right F412 Convertible top box lid closed switch F519 Convertible top front switch F202 Convertible top stowed switch F171 Tensioning strut up switch F408 Hall sensors work on the so-called Hall effect principle According to the Hall effect, a magnetic field acts perpendicular to the direction of current flow in a live conductor, resulting in voltage differences. These voltage differences are converted to signals and utilised by the convertible top operation control unit J256.The switching distance of the aforementioned Hall sensors can be in excess of 3 mm.The aforementioned Hall sensors are referred to as monopolar or unipolar Hall sensors. They react to the south pole of a permanent magnet.Hall sensorPermanent magnet623_063Switching distance30Tensioning strut up switch F408The tensioning strut up switch F408 is installed on the long tensioning strut pivot arm on the left-hand side as seen in the direction of travel. This switch is a Hall sensor. A permanent magnet is attached to the joint on the pivot arm. When the tensioning strut reaches its upper position, the tensioning strut up switch F408 and the permanent magnet are facing one another. In this position, the convertible top operation control unit J256 detects "tensioning strut up".Convertible top well down switch F520The convertible top well switch F520 is installed on the convertible top well at the rear right as seen in the direction of travel. This switch is a Hall sensor which detects when the variable convertible top well is in the lowered position. The convertible top cannot be opened when the variable convertible top well is in the upper position.Tensioning strut up switch F408623_069The variable convertible top well has to be actuated manually. It is lowered by pulling the handle and raised by pushing the handle. The advantage of the variable convertible top well is that it provides approx. 40 litres of additional load capacity in the boot when the convertible top is closed and the convertible top well raised.HandleConvertible top wellConvertible top well down switch F520623_064Convertible top lock closed switch, left F411 and convertible top lock closed switch, right F412The convertible top lock closed switch, left F411 and the convertible top lock closed switch, right F412 are located on the left and right-hand convertible top latch locks respectively. These switches are Hall sensors. The convertible top locking motor V223 engages and disengages the catch hooks on the convertible top. When the catch hooks are engaged in the lock, the switches send a signal which the convertible top operation control unit interprets as "catch hooks engaged in lock".Catch hook Convertible top lock closed switchPermanent magnet623_065 31Convertible top box lid closed switch F519The convertible top box lid closed switch F519 is located on the convertible top box lid latch motor V222. This switch is a Hall sensor. A permanent magnet is attached to the striker. The permanent magnet is directly facing switch F519 when the convertible top box lid is closed. The convertible top operation control unit then detects "convertible top box lid closed".Striker on convertible top box lidConvertible top box lid closed switch F519623_066Convertible top front switch F202The convertible top front switch F202 is installed in the direction of the travel, on the stationary part of the main bearing bolted to the body on the left-hand side of the vehicle. The switch is attached to the rear main bearing in the direction of travel. This switch is a Hall sensor. A permanent magnet is attached to the moving part of the main bearing. If the permanent magnet stops within the detection range of the switch, convertible top locking control unit detects "convertible top in front position".Permanent magnet623_067Convertible top front switch F20232Convertible top stowed switch F171The convertible top stowed switch F171 is installed in the direction of the travel, on the stationary part of the main bearing bolted to the body on the left-hand side of the vehicle. The switch is attached to the rear main bearing in the direction of travel. This switch is a Hall sensor. A permanent magnet is attached to the moving part of the main bearing. If the permanent magnet stops within the detection range of the switch, convertible top locking control unit detects "convertible top front".Permanent magnet623_068Convertible top stowed switch F171Convertible top box lid latch motor V222The convertible top box lid latch motor locks the convertible top box lid. Motor V222 is activated by the convertible top operation control unit J256. The motor is mounted on the anti-roll bar cross-member.623_070Convertible top box lid latch motor V22233Convertible top box lid latch unlocked switch F293 and convertible top box lid latch engaged switch F404Both switches are integrated in the convertible top box lid latch motor V222. The microswitches are actuated by nipples on the toothed segment. This switch tells the convertible top operation control unit J256 whether the convertible top box lid latch is engaged or disengaged.Convertible top box lid latch engaged switch F293623_070Convertible top box lid latch engaged switch F404Boot lidThe convertible top can only be operated when the boot lid is closed. When the convertible top cycle is initiated, the onboard power supply control unit J519 prevents the boot lid from being opened via the boot lid handle release button E234. On completion of the convertible top cycle, the boot lid handle release button E234 is re-enabled.623_072Switch for releasing the boot lidIf a convertible top cycle is initiated with the convertible top operating switch E137, the adjacent diagram in the dash panel insert indicates that the boot lid is open and, therefore, that the convertible top cannot be operated.Convertible top: Please close boot lid623_073 34Convertible top operation hydraulic pump V118Convertible top operation hydraulic pump V118 including • Hydraulic pump relay, convertible top operation J321 • Hydraulic pump relay 2, convertible top operation J588 • Power operated convertible top valve -1- N272 • Power operated convertible top valve -2- N341 • Power operated convertible top valve -3- N342The hydraulic pump together with the relays and valves form a unit. The hydraulic pump is installed in the boot, behind the luggage compartment trim on the left-hand side as seen in the direction of travel. The hydraulic pump is housed in an acoustic enclosure which provides sound insulation during pump operation.623_074Convertible top operation hydraulic pump V118The convertible top operation control unit J256 controls the hydraulic pump via both relays. The relays control the clockwise and anticlockwise operation of the pump.Depending on the deployment direction of convertible top (opening or closing), the valves guide the oil flow through the hose system and into the hydraulic cylinders.Power operated convertible top valve -2- N341 Power operated convertible top valve -1- N272 Power operated convertible top valve -3- N342Hydraulic pump relay 1, convertible top operation J321 Hydraulic pump relay 2, convertible top operation J588623_11835The hydraulic system is self-locking. This means that the pressure generated by the pump is maintained within the system for approx. 5 minutes. The system de-energises the valves after approx. 5 minutes, causing the hydraulic system to depressurise.If the convertible top is in an intermediate position and the hydraulic system depressurises, the convertible top will collapse depending on its position. Also, the convertible top box lid will close depending on its position. In the worst-case scenario, the convertible top will collide with the convertible top box lid. If this happens, the convertible top or the convertible top box lid may become damaged. It may also be the case that neither the convertible top box lid nor the convertible top reaches one of its limit positions. It is no longer possible to operate the convertible top because, in this case, the convertible top operation control unit receives implausible signals. The message "Convertible top: no operation possible" is displayed in the dash panel insert.Collision of the convertible top and convertible top box lid623_076To be able to continue operating the convertible top, the convertible top box lid must be moved manually into a limit position. The convertible top cycle can then be resumed. If the limit position was reached by opening the convertible top box lid, the convertible top box lid must be secured to prevent it from slamming shut. Refer to description on page 43. The system can also be depressurised manually by turning off the ignition and pushing or pulling the convertible top operating switch E137 for approx. 5 seconds.623_077Convertible top operating switch E137!36Note Avoid collisions between the convertible top and the convertible top box lid while the top is lowering.Hydraulic cylinderThe convertible top of the A3 Cabriolet ’14 is equipped with three hydraulic cylinder pairs. Two cylinders are responsible for actuating the convertible top box lid, two other cylinders are responsible for the roof bows, and the last two are responsible for the convertible top.Cylinder pair for tensioning strutCylinder pair for convertible topCylinder pair for convertible top box lid623_078The hydraulic cylinders can be actuated from both sides and therefore act in two working directions.Compression stageHydraulic cylinderTension stagePiston rod623_079Hydraulic connection PistonsHydraulic lineHydraulic connection37Tensioning strut down switch F517The tensioning strut down switch F517 is integrated in the hydraulic cylinder responsible for the movement of the tensioning strut, on the left-hand side of the vehicle as seen in the direction of travel. This sensor is a Hall sensor, which is attached to the hydraulic cylinder and can be replaced separately. When the tensioning strut is in its lowest position (tensioned), the cylinder is fully extended and the Hall sensor sends a signal which the convertible top operation control unit interprets as "tensioning strut down".623_080Tensioning strut down switch F517Convertible top box lid up switch F407The convertible top box lid switch F407 is integrated in the hydraulic cylinder responsible for the movement of the convertible top box lid, on the left-hand side of the vehicle as seen in the direction of travel. This switch is a Hall sensor, which is attached to the hydraulic cylinder and can be replaced separately. When the convertible top box lid is fully open, the cylinder is fully retracted and the Hall sensor sends a signal which the convertible top operation control unit interprets as "convertible top box lid open".623_081The convertible top box lid switch F407 is built into the cylinder38Hydraulic cylinder of main bearingThere are no Hall sensors in the hydraulic cylinders of the main bearing. The hydraulic cylinders of the main bearing are responsible for the movement of the convertible top.623_082Hydraulic cylinder of main bearingConvertible top control unit J256Convertible top control unit J256The convertible top operation control unit J256 is fitted in a compartment in the boot, behind the trim over the convertible top operation hydraulic pump V118; this is on the left-hand side of the vehicle as seen in the direction of travel. The control unit is integrated in the vehicle's bus system via the convenience CAN bus and exchanges data with other systems across this bus. The control unit controls and monitors each individual convertible top operating cycle. It collects the information generated by the sensors as well as information from other bus users, evaluates it and controls the actuators accordingly.623_083The control unit is also responsible for system diagnostics. If irregularities are detected in the system or if signals are received at the wrong time, the convertible top cycle is stopped. An event is registered and a message is displayed in the dash panel insert J285.Convertible top: malfunction! You can continue driving623_084 39To protect the convertible top operation hydraulic pump V118 against overload, the control unit monitors the runtime of the convertible top. If the convertible top has been running continuously for approx. 2 minutes and is closed by this time, the control unit suppresses operation of the convertible top for approx. 10 minutes.The maximum continuous duty cycle of the hydraulic pump is limited to approx. 170 seconds. This means that the hydraulic pump shuts off after approx. 170 seconds of continuous duty, regardless of the convertible top’s momentary position. Operation of the convertible top is subsequently suppressed for approx. 20 minutes due to the danger of overheating. This is indicated by the adjacent diagram in the dash panel insert. Convertible top: no operation possible623_085Convertible top locking motor V223The convertible top locking motor V223 is attached to the convertible top in the middle as seen in the direction of travel. The motor uses a linkage to actuate the two catch hooks which lock the roof into the window frame.623_086Catch hookConvertible top locking motor V223Linkage40Convertible top box lid closed switch F295The convertible top box lid closed switch F295 is built into the convertible top locking motor V223. This switch is a Hall sensor. When the motor V223 has locked the convertible top latch, a retaining plate is within the detection range of the Hall sensor. This produces a signal which the convertible top operation control unit detects as "convertible top lock closed".Convertible top box lid closed switch F295Retaining plate623_087Convertible top lock open switch F294The convertible top box lid open switch F294 is built into the convertible top locking motor V223. This switch is a Hall sensor configured as an incremental encoder, or rotary encoder, i.e. the Hall sensor measures the number of revolutions of motor V223. The convertible top operation control unit evaluates the signals generated by the Hall sensor. When the Hall sensor has measured the corresponding number of revolutions, the convertible top operation control unit detects "convertible top lock open".Convertible top lock open switch F294623_08841Emergency operationIn the event of a malfunction, the convertible top can be closed manually. If possible, the convertible top should be emergencyoperated by two persons. The convertible top cannot be emergency-operated unless the system is depressurised. The system depressurises automatically approx. 5 minutes after turning the ignition off. The system can also be depressurised manually by turning off the ignition and pushing or pulling the convertible top operating switch E137 for approx. 5 seconds.Closing the convertible top Conditions: • • • • Parking brake closed All side windows lowered Ignition turned off Hydraulic system is depressurised The box wrench from the vehicle's tool kit is required for manual operation of the convertible top.First of all, the convertible top box lid must be unlocked. To do this, open the boot lid and fold down the backrest of the right seat seat as seen in the direction of travel (arrow) .623_014Now remove the box wrench from the vehicle tool kit and close the boot lid. From inside the vehicle, pull down the release loop (arrow) and unlock the convertible top box lid.623_01542Push the covers on both sides of the vehicle in the direction of the arrow until they engage.623_016As the convertible top box lid can close involuntarily and cause injury or damage, the convertible top box lid must be held during the entire opening cycle. Move the convertible top box lid into the upright position (arrow 1) and hold it there with your hands. After that, secure the convertible top box lid by pushing back the left and right-hand hinges (arrow 2). It is no longer necessary to hold the convertible topbox lid in this position.623_017Remove the cover from the trim and apply the box wrench. To open or disengage the catch hooks, turn the box wrench clockwise as far as it will go. Then remove the box wrench.623_018To lift out the convertible top, place the seat next to the vehicle, grab the convertible top by the front edge and pull it out completely (arrow). The convertible top tensioning strut must then be raised until the convertible top box lid can be closed.623_019 43As the convertible top box lid can close involuntarily and cause injury or damage, the convertible top box lid must be held during the entire closing cycle. Unlock the convertible topbox lid by pulling the left and right hinges and slowly close the lid with manual assistance. Then lower the tensioning strut of the convertible top (arrow 2) until it rests on the convertible top box lid.623_020The final step is to lock the convertible top into the window frame. For this purpose, push the convertible top onto the window frame (arrow).623_021Then apply the box wrench and turn it anticlockwise as far as it will go and remove the box wrench. Make sure that the catch hooks engage in the top sections of the lock and that the convertible top is correctly locked.623_022!Note After the convertible top has been emergency-operated, the convertible top box lid is unlocked. Caution: do not reach into the convertible top linkage or other moving parts during emergency operation of the convertible top. Danger of injury!Reference Please refer to the Owner’s Manual for further information on emergency operation.44Data bus overviewThe overview shows, by way of example, some of the information exchanged via data bus.Instrument panel control unit J285 Display convertible top message in instrument cluster display ← E Ambient temperature → A Rear driver’s side indow regulator control unit with motorJ1016 Rear passenger’s side indow regulator control unit with motor J1017 Side window closing ← E Lower side windows ← E (LIN users of door control units J386 and J387)Door control unit, driver side J386 Front passenger door control unit J387 Locked and closed status of convertible top ← E Side window closing ← E Lower side windows ← E Side window closing → A (to LIN users J1016 and J1017) Side window opening → A (to LIN users J1016 and J1017)Onboard power supply control unit J519 (= BCM_01) Locked and closed status of convertible top ← E Locked and open status of convertible top ← E Convertible top in intermediate position ← E Boot lid release enabled/disabled ← E Comfort request via key ← E Rear window heater on/off status → A NO contact on/off status → A Terminal 15 status → A Convenience opening and closing request signal → A Enable convertible top operation → A Actual and nominal status of external vehicle locking → A Boot lid status → A Sleep mode readiness → AConvertible top control unit J256 Locked and closed status of convertible top ← A Unlocked status of convertible top ← A Locked and open status of convertible top ← A Convertible top in intermediate position ← A Convertible top opening movement ← A Convertible top closing movement ← A Boot lid release enabled/disabled ← A Side window closing → A Lower side windows ← A Display convertible top message in instrument cluster display → A Comfort request via key ← A Speed signal → E Ambient temperature → E Convenience opening and closing request signal → E Sleep mode readiness → E Rear window heater on/off status → E NO contact on/off status → E Terminal 15 status → E Enable convertible top operation ← E Boot lid status → E Actual and nominal status of external vehicle locking → EClimatronic control unit J255 Locked and closed status of convertible top ← E Locked and open status of convertible top ← E Convertible top opening movement ← E Convertible top closing movement ← EData bus diagnostic interface J533 (Gateway) Locked and closed status of convertible top ← E Unlocked status of convertible top ← E Locked and open status of convertible top ← E Comfort request via key ← E Speed signal → A Sleep mode readiness → AAccess and start authorisation control unit J518 Locked and closed status of convertible top ← E Convertible top opening movement ← E Convertible top closing movement ← E Comfort request via key ← EKey: Data bus in general LIN bus ← E → A Receiving data (input) Sending data (output)Trailer detector control unit J345 Comfort request via key ← E623_07145Occupant safetyComponentsThe passive occupant and pedestrian protection system in the Audi A3 ’14 comprises the following components and systems: • • • • • • • Airbag control unit Driver and passenger airbags Front side airbags (head-thorax airbag) Driver side knee airbag Front airbag crash sensor Crash sensors for side impact detection in the doors Rear crash sensor for side impact detection on heel plate • Front inertia reel seat belts with electric and pyrotechnic belt tensioners • Seat belt warning for all seats • Seat belt switches on all seats in the seat belt buckles • Seat occupancy sensor in front passenger seat • Rollover protection46Additional equipmentThe vehicle is optionally available with a key-operated disabling switch for the front passenger front airbags with accompanying warning lamp. Due to the different statutory provisions and requirements for car makers in the various markets, equipment specifications may vary.623_00547System overviewThe system overview shows, by way of example, the equipment options available for a German-specification vehicle.623_00648Key to illustration E24 E25 E224 E258 E259 Driver side seat belt switch Passenger side seat belt switch Airbag disabling switch, passenger side (optional) Rear seat belt switch, driver side Rear seat belt switch, passenger side K19 K75 K145 Seat belt reminder warning lamp Airbag warning lamp Passenger airbag off warning lamp (optional)G128 G179 G180 G256 G283 Passenger side seat occupancy sensor Side airbag crash sensor, driver side Side airbag crash sensor, passenger side Rear side airbag crash sensor, driver side (centre of heel plate) Front airbag crash sensor, driver side (front end)N95 N131 N153 N154 N199 N200 N646 N647 Driver side airbag igniter Passenger side airbag igniter 1 Seat belt tensioner igniter 1, driver side Seat belt tensioner igniter 1, passenger side Side airbag igniter, driver side Side airbag igniter, passenger side Rollover protection trigger, driver side Rollover protection trigger, passenger sideT16 J234 J285 J533 J854 J855 Airbag control unit Control unit in dash panel insert Data bus diagnostic interface (gateway) Front left seat belt tensioner control unit (optional) Front right seat belt tensioner control unit (optional)16-pin connector, diagnostic portPowertrain CAN bus Convenience CAN bus Diagnostics CAN bus Input signal Output signal49Side airbagThe side airbags, side airbag igniter, driver side N199, and side airbag igniter, passenger side N200 are configured as head-thorax airbags. The head-thorax airbags are designed to protect not only the body, but also the head of the front occupants. The side airbags on the Audi A3 Cabriolet ’14 have approx. 8.5 litres more capacity than the side airbags on the A3 and the A3 Sportback. By integrating the side airbags in the front seat backrests, the airbags are optimally positioned relative to the front occupants irrespective of the seat setting.623_011The side airbag igniter activated by the airbag control unit (fusible resistance wire including a small quantity of pyrotechnics) ignites the priming charge. This in turn ignites the actual propellant charge, which in this case is a pyrotechnic solid propellant. The gases liberated during combustion of the propellant charge flow through outlet orifices via the filter into the airbag, whichthen unfolds and fully inflates. The seal between the outlet orifices protects the pyrotechnics against moisture and is destroyed by the heat generated.Seal Filter (contains the propellant charge)Priming charge623_012IgniterPropellant chargeOutlet orifices50Electrical wiring loom for side airbagThe electrical wiring loom of the front side airbag can be completely replaced on the Audi A3 Cabriolet ’14. Therefore, it is no longer necessary to replace the complete airbag module if the wiring loom is damaged. This is possible because the ground cable used to protect the pyrotechnics against static connects directly to the airbag module connector. After contacting the connector, the ground cable connects the gas generator housing to the body in an electrically conductive manner.Cover Locking deviceContactMechanically encoded housing609_014a 609_014Reference Please refer to the information given in ETKA.Rear side airbag crash sensor, driver side G256The side airbag crash sensor, rear driver side G256 is a capacitive acceleration sensor. Although crash sensor G256 is designated "rear driver side", it is fitted in the rear of the vehicle at the centre of the heel plate. If G256 senses a side impact, it informs the airbag control unit. The Y sensor integrated in the control unit checks the crash signal from G256 for plausibility. As soon as a deployable impact is detected, the airbag control unit deploys the belt tensioners and the head-thorax airbag on the impact-facing side of the vehicle.Rear side airbag crash sensor, driver side G256623_013 51Rollover protectionWithout special modifications, cabriolets would not adequately protect their occupants during a rollover accident as they do not have a rigid roof. To counteract this, the Audi A3 Cabriolet ’14 is equipped with a rollover protection system. In contrast to the outgoing model, which has a rigid rollover protection system, the Audi A3 Cabriolet ’14 is equipped with a retractable rollover protection system. When deployed, the rollover protection system, together with the body strengthening measures and the rigid A posts, provides a survival space for the occupants. An additional sensor detects an imminent rollover and deploys the rollover protection system. This sensor is known as a "roll over sensor" and is integrated in airbag control unit J234. The roll over sensor cannot be replaced separately. If an imminent rollover is detected, the rollover protection system deploys and the belt tensioners are ignited. In all crash events in which airbags and/or belt tensioners are ignited, the rollover protection system deploys as a precautionary measure. If no rollover occurs in the course of the crash, the rollover protection system can easily be reset due to its reversability.623_005a52Cassettes with anti-roll barsThe rollover protection system on the Audi A3 Cabriolet ’14 consists of two cassettes which accommodate the anti-roll bars and other components. Different cassettes are used on the driver and passenger sides. Therefore, care must be taken to ensure that the cassettes are fitted on the correct side of the vehicle. The correct installation direction of the cassettes is indicated by an arrow on the cassettes. The specified tightening sequence must be adhered to.Arrow indicating installation direction SpringRelease lever CassetteRatchet railPawl623_007Rollover protection trigger, driver side N646 and rollover protection trigger, passenger side N647The retractable anti-roll bars are preloaded by a spring. The antiroll bar is held in its lower position by the U bar of the rollover protection trigger. When the rollover protection trigger is energised by the airbag control unit J234 due to an imminent rollover or crash, the trigger releases the U bar and the anti-roll bar deploys upwa