TECHNICAL DOCUMENTATION
SSP 626 Audi Basics of Engine Technology

This PDF is currently unavailable.
Read document text
Self Study Programme 626 For internal use onlyAudi Basics of Engine TechnologyAudi Service Training BackForwards Ξ ContentsAudi engine technology is distinguished by continual advancement and development with the aim of improving efficiency. That is part and parcel of the customer's continuing and growing enthusiasm for the vehicle. That alone produces a broad range of engines for a wide diversity of demands and vehicle types. Added to that there are market-specific variations. New engine technologies have been presented in the Audi selfstudy programmes for many years. The chief objective of doing so is to equip service organisation staff with an understanding of the numerous innovations and processes to a level beyond the information given in the worksop manual repair instructions.This self-study programme follows an approach that supplements the previous objectives. On the pages of this self-study programme you will find information on the fundamental design and function of Audi engines and associated technologies. Numerous engine subsystems are also presented and explained.This SSP contains QR codes which you can use to access additional interactive content, see "Information on QR codes" on page 123.Training modules on the Audi power unitsATE 219 P.1 4-cylinder petrol engines Series EA211 ATE 218 P.1 4-cylinder petrol engines Series EA888 Gen. 3 ATE 217 P.1 4.0l V8 TFSI engine Expert training course ATE 216 P.1 2.5l TFSI engine ATE 215 P.2 W12 engine ATE 214 P.1 3.6l V6 FSI engine ATE 213 P.1 Audi V engine series ATE 212 P.2 4-cylinder engines Series EA111 ATE 211 P.1 4-cylinder engines Series EA888ATE 231 P.1 Audi g-tronATE 226 P.1 1.6l / 2.0l TDI engine Series EA288 ATE 225 P.1 3.0l V6 TDI engine 2. Generation/Biturbo ATE 224 P.1 6.0l V12 TDI engine ATE 223 P.1 4.2l V8 TDI common-rail engine ATE 222 P.1 3.0l TDI clean diesel engineAdvanced trainingATA 211 P.2 Petrol injection engines ATA 201 P.2 Fundamentals of petrol/diesel engine technologyATA 222 P.2 Fuel injection systems Diesel engine626_086Learning objectives of this self-study programme In this self-study programme, you will learn the fundamental basics of Audi engine technology. It forms the basis for Training Module ATA 201 P.2. When you have worked through this Self Study Programme, you will be able to answer the following questions: • What types of engine are used at Audi? • How are the components of the engine's mechanical and control systems constructed? • How do the components of the engine's mechanical and control systems operate? • What engine subsystems are there and how do they work?2ContentsIntroductionPrinciple of operation of a four-stroke petrol engine _____________________________________________________________________________________________________ 4 Engine technology at Audi __________________________________________________________________________________________________________________________________ 6Engine codeIntroduction __________________________________________________________________________________________________________________________________________________ 7 Engine code on the vehicle __________________________________________________________________________________________________________________________________ 8Engine typesThe in-line and the V engine _______________________________________________________________________________________________________________________________ 10 The VR and the W engine ___________________________________________________________________________________________________________________________________ 11Engine componentsCylinder block _ ______________________________________________________________________________________________________________________________________________ 12 Crankshaft ___________________________________________________________________________________________________________________________________________________ 18 Piston _ ________________________________________________________________________________________________________________________________________________________ 22 Piston rings __________________________________________________________________________________________________________________________________________________ 27 Gudgeon pin _________________________________________________________________________________________________________________________________________________ 28 Connecting rod ______________________________________________________________________________________________________________________________________________ 29 Timing belt drive system ___________________________________________________________________________________________________________________________________ 31 Chain drive system __________________________________________________________________________________________________________________________________________ 33 Balancer shafts ______________________________________________________________________________________________________________________________________________ 37 Cylinder head ________________________________________________________________________________________________________________________________________________ 39 Gaskets and seals on the engine _ __________________________________________________________________________________________________________________________ 44 Camshafts ___________________________________________________________________________________________________________________________________________________ 46Engine timingValve gear ____________________________________________________________________________________________________________________________________________________ 48 Camshaft timing adjuster __________________________________________________________________________________________________________________________________ 52 Engine lubrication _ __________________________________________________________________________________________________________________________________________ 56SubsystemsCrankcase breather _ ________________________________________________________________________________________________________________________________________ 71 Engine cooling system ______________________________________________________________________________________________________________________________________ 73 Coolant thermostat as 3/2-way valve _____________________________________________________________________________________________________________________ 78 Air supply system ___________________________________________________________________________________________________________________________________________ 81 Intake manifold _____________________________________________________________________________________________________________________________________________ 85 3-stage variable intake manifold __________________________________________________________________________________________________________________________ 86 Forced induction systems __________________________________________________________________________________________________________________________________ 88 Intercooler ___________________________________________________________________________________________________________________________________________________ 97 Exhaust gas recirculation _ __________________________________________________________________________________________________________________________________ 98 Exhaust system _ ___________________________________________________________________________________________________________________________________________ 103 Ignition system ___________________________________________________________________________________________________________________________________________ 114 Glow plug system _________________________________________________________________________________________________________________________________________ 118 Fuel system ________________________________________________________________________________________________________________________________________________ 120AnnexInformation on QR codes _ ________________________________________________________________________________________________________________________________ 123The Self Study Programme teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a Repair Manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. This content is not updated. For further information on maintenance and repair work, always refer to the current technical literature.NoteReference3 BackForwards Ξ ContentsIntroductionPrinciple of operation of a four-stroke petrol engineAll Audi internal combustion engines are four-stroke engines. The applies regardless of whether the engine runs on petrol, diesel, natural gas or ethanol. A crankshaft converts the reciprocating motion of the pistons into rotary motion. The motion of the pistons inside the cylinders is transmitted by way of connecting rods connected to crank arms. In the course of 2 revolutions of the crankshaft (720°) work is only done for 1 revolution (320°). So that the engine runs smoothly, multiple pistons that have their power strokes offset from one another are used. Each cylinder has 2 valves, the inlet valve (I) and the exhaust valve (E). Both valves are opened and closed at precisely the right times by an actuating mechanism.1st stroke – inductionAt the start of the 1st stroke the piston is at top dead centre (TDC). The exhaust valve is closed and the inlet valve opened. The piston moves towards the crankshaft. As the piston moves downwards, air or a mixture of fuel and air is drawn into the cylinder through the inlet valve. Engines with internal mixing, such as diesel engines and direct-injection petrol engines, draw in only air. With external mixing, such as is the case with engines with intakemanifold fuel injection, a mixture of air and atomised fuel is drawn in. When the piston has reached bottom dead centre (BDC), the inlet valve is closed and the 1st stroke is complete.2nd stroke – compression and ignitionThe piston moves towards top dead centre. The mechanical work required to do so is provided by the kinetic energy of the rotating inertial mass, or in multi-cylinder engines from the power stroke of one of the other cylinders. The air or fuel-and-air mixture in the cylinder is now compressed to a faction of its original volume. The amount by which it is compressed depends on the type of engine. In unturbocharged petrol engines, a compression ratio of more than 10:1 is normal. Diesel engines without a turbocharger can have a compression ratio as high as 20:1. With a turbocharger it is significantly lower. Compression heats the fuel-and-air mixture in a petrol engine to around 450°C. In a diesel engine, the air reaches a temperature of about 650°C. Shortly before the piston reaches top dead centre, ignition is initiated in a petrol engine and the pre-injection phase in a diesel engine. The precise timing is dependent on engine load and speed.Inlet valve (I)Exhaust valve (E)626_238 4626_239 BackForwards Ξ Contents3rd stroke – powerAfter the piston has reached top dead centre, the spark-ignited fuel-and-air mixture in a petrol engine continues to burn. At this point in a diesel engine, the main injection phase takes place and the fuel ignites spontaneously. The temperature of the burning fuel-and-air mixture in a petrol engine is between 2,200 and 2,500°C. The pressure inside the combustion chamber can be as much as 120bar. In a diesel engine the respective figures are 1,800 to 2,500°C and 160bar. The piston now moves towards bottom dead centre. The burning fuel-and-air mixture performs mechanical work on the piston and at the same time cools down. Shortly before the piston reaches bottom dead centre, a residual pressure of around 4bar is present in a petrol engine. In a diesel engine it is about 3bar. The exhaust valve starts to open.4th stroke – exhaustWhen the piston starts to move away from bottom dead centre, the upward movement pushes the exhaust gases out of the cylinder. At the end of the exhaust stroke the phenomenon known as valve overlap occurs. The inlet valve is opened before the piston reaches top dead centre and before the exhaust valve has closed. The exhaust valve does not close until shortly after the piston has reached top dead centre.626_240626_241Valve timingEach cylinder has at least 1 inlet and 1 exhaust valve. But 3, 4 or 5 valves per cylinder are not unusual. Because the gas replacement cycle is faster, engines with 4 valves per cylinder can rev higher and so can produce more power than engines with only 2 valves per cylinder. Engines referred to as 16-valve engines are usually 4-cylinder engines with 4 valves per cylinder. On standard engines, the valves are controlled by one or more camshafts. The camshafts are driven by a timing belt or timing chain running off the crankshaft. The camshaft rotates at half the speed of the crankshaft. In a pushrod engine, the camshaft is not in the cylinder head but lower down in the engine and operates the valves by means of pushrods and rocker arms, while in a side-valve engine (used until the 1950s) it operates the valves via tappets. If the camshaft is placed in the cylinder head, the pushrods can be dispensed with. This is the design most commonly used on modern engines. In this case, the valves are operated by means of rocker arms, bucket tappets or lever arms.5 BackForwards Ξ ContentsEngine technology at Audi1.2l TFSI engine Engine design probably reflects the Audi credo of "Vorsprung durch Technik" better than anything else, characterised as it is by the most advanced technologies in terms not only of production but also efficient engine operation. In that connection we can cite the widespread use of TDI diesel engines in the early 1990s which marked the start of that development. The development of a new engine has to take account not only of the performance aspirations but also of economy and especially the conservation of natural resources. As well as the advanced TDI technology – now incorporating modern common rail technology – numerous other technical achievements have been added. Examples of note are FSI turbocharged petrol direct injection, "cylinder on demand" selective cylinder shut-down, and the ultra-low emission system (SCR) on diesel engines. The range is completed by engines that can also run on alternative fuels such as natural gas or bio-ethanol and so make a contribution to sustainable transport. As well as adopting new technologies, the Audi range of engines has also expanded enormously over recent years. The diversity now extends from 4-cylinder in-line engines with a capacity of 1.2 litres to the imposing 6.3-litre W12 engine. And in between there are numerous modern power units such as the EA888 Series with its 1.8l and 2.0l TFSI engines that are used across a number of vehicle models – mounted both transversely and in line.626_006626_0023.0l V6 TDI engine2.0l TDI engineApart from the W12 engine already mentioned, peak performance among the petrol engines is defined primarily by the 4.0l V8 TFSI, which courtesy of selective cylinder shut-down and twin turbochargers can operate both as a high-performance and an economy engine. Among the diesels, the 3.0l V6 TDI is worthy of special mention by virtue of its wide choice of variants. There are ultra-low emission system (SCR) versions that meet the very strictest emission standards as well as performance varieties with twin turbochargers. The continuing development of engines at Audi will undoubtedly be marked by efficiency improvement considerations. In that respect, lightweight design and new materials as manifested by the Audi ultra concept have a major role to play. And there will be more systems and technologies in the future that will continue to make Audi cars what the Audi credo promises.626_0043.0l V6 TFSI engine Audi – Vorsprung durch Technik626_005626_0766 BackForwards Ξ ContentsEngine codeIntroductionIn order to reduce the diversity of engine codes, the engine codes are now made up of 4 letters instead of 3. This applies to engines with the same basic unit, but different power outputs. The only means of differentiating in performance terms between these engines is by means of the engine control unit in which the software has been modified to achieve a different power output and torque. The engine codes are not changed for engines with a modified exhaust-gas concept. Answers to frequently asked questions: 1. What is the advantage of the 4-letter engine code? • It reduces the diversity of engine codes. • A separate engine code is no longer required for each performance variant. 2. Will there still be engines with a 3-letter engine code? • Yes, 3-letter codes will continue to be used for engines with only one power rating. 3. Will engines with more than one performance variant which already have 3-letter engine codes be given new engine codes? • No, existing engine codes will not be changed.The allocation of the new engine codes can be illustrated by the following example:2.0l 103kW TDI2.0l 100kW TDI2.0l 96kW TDIBKDAZVBEEOld 3-letter engine codesNew 4-letter engine codesCAGA, 105 kWCAGB, 100 kWCAGC, 88 kWCAHA, 125 kWCAHB, 120kW626_088The new generation of engine codes can be identified as follows: • The engine code starts with a "C". • On the cylinder block the 3-letter engine code is retained.• The 4-letter engine codes will only appear on the vehicle data sticker, the engine control unit and the type plate.7 BackForwards Ξ ContentsEngine code on the vehicleOn the shock absorber: The 4-letter engine code is documented on the identification plate on the front right shock absorber.On the timing belt cover: A sticker carrying the 3-letter engine code and a serial number is affixed to a visible part of the engine (timing belt guard, cylinder head cover).626_016626_015On the cylinder block: On the cylinder block the 3-letter engine code is retained. It is stamped on the cylinder block.626_014On the engine control unit: A sticker carrying the 4-letter engine code is affixed on a visible part of the engine control unit.626_019 8 BackForwards Ξ ContentsIn the spare wheel well: The 4-letter engine code is documented on the vehicle data sticker in the spare wheel well in the luggage compartment.626_017In the service record: The 4-letter engine code is documented on the vehicle data sticker in the service record.626_013626_018 9 BackForwards Ξ ContentsEngine typesThe in-line and the V engineThe in-line engine is one of the oldest and simplest engine designs in which the cylinders are arranged in a row. The in-line engine is relatively compact, providing the number and displacement of cylinders is limited. A 2.0l 4-cylinder engine will fit in almost any engine compartment, for example. The more cylinders an in-line engine has, the longer it becomes and so it ceases to be suitable for smaller engine compartment. On Audi engines, the cylinders are generally numbered from the right, which is the end of the engine opposite to the flywheel end. With the development of the V engine, it has been possible to replace a small in-line 4-cylinder engine with a 6-cylinder engine without requiring any additional space. With the V engine, the cylinders are arranged in 2 planes, also referred to as cylinder banks, at an angle to one another. When seen from the front, it is easy to see why this is called a V engine. The angle between the cylinder banks of most V engines is either 60° or 90°. The V engines used at Audi have 6, 8 or 10 cylinders.In-line engine4 3 2 1Flywheel endFiring orders: 3-cylinder engine 4-cylinder engine 5-cylinder engine 1-2-3 1–3–4–2 1–2–4–5–3626_010V engineFlywheel endDirection of travel when mounted in line3Direction of travel when transversely mounted2190°6 5 4Firing orders: 6-cylinder engine 8-cylinder engine 10-cylinder engine 1–4–3–6–2–5 1–5–4–8–6–3–7–2 1–6–5–10–2–7–3–8–4–9Bank 1 Bank 2Direction of travel626_01110 BackForwards Ξ ContentsThe VR and the W engineThe next step was the development of the VR engine This engineering design makes more space available in the engine compartment. The V profile was retained but the cylinders are closer together. The angle of the cylinder bank was reduced to 15° to make the unit more compact. This means that the VR engine, in contrast to the conventional V engine, requires only one cylinder head. The VR engine is also narrower than a V engine and shorter than an in-line multiple cylinder engine. Another benefit of the VR concept is that it retains the smooth running characteristics of an in-line engine. The compactness of the VR design makes it possible to accommodate 6 cylinders in a very small space. However, if more cylinders and a higher displacement is required, the VR design also becomes too long. The answer to this problem is the W engine in which two VR banks are placed side by side. The name of this engine is also derived from its profile. When viewed from behind, the cylinders appear to have a double V (side-by-side) arrangement which can be interpreted as a W. As is the case with the VR engine, the cylinders in each cylinder bank are offset by 15° and the angle between the two cylinder banks is 72°. Owing to its design, the W engine has an extremely compact multiple cylinder engine that takes up very little space in the engine compartment compared with a V engine. W engines therefore provide the power and performance characteristics of larger engines in vehicles with smaller engine compartments.VR engineFlywheel end6Firing order: 6-cylinder engine 1–5–3–6–2–4352Bank 2Bank 115 °41Direction of travelW engine72°Flywheel end6 11 1254 9 10626_00115 °32 7 815°1Firing order: 12-cylinder engine 1–12–5–8–3–10–6–7–2–11–4–9Bank 1Bank 2Direction of travel626_01211 BackForwards Ξ ContentsEngine componentsCylinder blockThe cylinder block is the core component of an engine. It essentially reflects the type of power unit used. A cylinder block has to satisfy enormous demands. For example, it has to withstand the high combustion pressures and ensure the heat generated by combustion is rapidly dissipated.Cylinder block variations according to cylinder configuration5-cylinder in-line engine 12-cylinder W engine626_021626_020Function• Absorption of the gas-pressure and inertia forces in the crankshaft bearings or in the cylinder head mounting bolts/studs. • Retaining the crankshaft drive gear, consisting of pistons, connecting rods, crankshaft and flywheel. • Incorporation of the cylinders. • Retaining the crankshaft. • Incorporation of channels for circulation of fluids. • Integration of a crankcase venting system. • Connection to the gearbox and the valve gear drive system. • Holding and guiding power transmission components such as chains. • Connection and mounting of auxiliary units. • Sealing off the crankcase from the outside.Stresses• Gas pressures occurring inside the engine • Internal inertial torque (twisting forces) resulting from rotating and oscillating inertial forces. • Internal torsional forces (tilting forces) between the individual cylinders. • Crankshaft torque • Free inertial forces and torque resulting from oscillating inertial forces.12 BackForwards Ξ ContentsIntegrated systemsInside the cylinder block are the cylinders inside which the pistons move up and down. The pistons are connected to the crankshaft via connecting rods. The surfaces of cylinders, pistons and piston rings must be especially resistant to wear as they have to ensure that the combustion chambers remain sealed. In addition, low-friction guidance of the pistons in the individual cylinders reduces fuel consumption as the piston can then move much more easily. There are also numerous channels in the cylinder block for the lubrication and cooling systems.CylinderCylinder block PistonConnecting rod626_022CrankshaftOil channelsOil flow to cylinder head Main oil galleryCooling systemCoolant flow from and to the cylinder head626_023626_026Piston cooling jetRiser pipe from oil filter to oil coolerMain bearingCoolant connections for oil cooler13 BackForwards Ξ ContentsDistinguishing between different cylinder block typesFundamentally, engines can be distinguished on the basis of their cylinder blocks. The number and arrangement of the cylinders they contain allows us to classify engines as in-line, V, VR or W engines. But even within those categories, cylinder blocks can be further classified on the basis of the following criteria:Design of the upper face Open-deck construction Closed-deck constructionCharacteristics of the cylinders Cylinder liners Cylinder inner surface material • Plasma coating (hypo-eutectic) • Alusil® process (hyper-eutectic) Cylinder inner surface structure Composite technologyCylinder block manufacture Die casting Gravity die castingLost-foam process Sand casting Squeeze castingDesign of the upper faceA feature by which types of cylinder block can be distinguished is the design of the upper face (deck) of the cylinder block. A distinction is made between "open deck" and "closed deck" designs.Open-deck construction An open-deck design is distinguished by the fact that the space surrounding the cylinders is open at the top. The coolant it contains is thus able to have a cooling effect right up as far as the most highly stressed area at the top of the cylinder and dissipate the heat over the full height of the cylinder. In addition, with this design, distortion of the cylinders when mounting the cylinder head can be significantly limited. A disadvantage is the reduced rigidity of the cylinder block. That effect can be offset by the use of a cylinder head gasket made of metal. In general, this design allows a lot of scope for making the cylinder block manufacturing process more efficient.Closed-deck construction With a closed-deck design, the space around the cylinders is largely closed off. In this case the deck has only separately defined openings that allow the coolant to flow from the area around the cylinders into the cylinder head. The advantage of this design is the significantly greater rigidity of the cylinder block compared with an open-deck design. A clear disadvantage is that the cooling effect cannot extend over the full height of the cylinder. In addition, cylinder blocks of this type are very expensive to produce.Open deckClosed deck CoolantCoolant626_024 14626_025 BackForwards Ξ ContentsCharacteristics of the cylindersThe character of a cylinder is definitively determined by 4 aspects: • Cylinder liners • Cylinder inner surface material • Cylinder inner surface structure • Composite technologyCylinder linersTo reduce the friction and wear on the pistons and cylinders, the pistons are not in direct contact with the cylinder block. Instead, cast integral or fitted into the cylinder bock there are thin-walled sleeves inside which the pistons move up and down. Those sleeves are called "cylinder liners". A positive side-effect of cylinder liners is that they improve the stability of the cylinder block.PistonCylinder linerCylinder block626_034Cylinder inner surface material In order to save weight, cylinder blocks are increasingly being made of aluminium alloys. As the pistons are also made of the same material, this results in substantially diminished running qualities inside the cylinders. The reason for that is that the frictional coefficient between two aluminium surfaces is very high. To improve the running characteristics and still keep the cylinder wear as low as possible, the contact surface material has to be suitably treated. The aim is to create a cylinder inner surface that is as hard and low-friction as possible. For that purpose, 2 processes have been developed. The first involves coating the inner surface of the cylinder by means of plasma coating. The alternative is what is known as the Alusil® process. As both processes act directly on the inner surface of the cylinder in the cylinder block, engines produced in this way do not require cylinder liners.15 BackForwards Ξ ContentsPlasma coating The plasma coating ensures that the pistons can slide over the inner surface of the cylinder with as little friction as possible. As the layer applied is only 0.2mm thick and the use of a cylinder liner is not necessary, a substantial weight saving can be achieved with engines of this type. The coating is applied with the aid of a rotating burner. The burner is fuelled by a plasma gas which is ignited by an arc as it exits the jet. As a result, the plasma gas is heated to a temperature of around 11,700°C and transformed into a plasma. At the same time it is accelerated to a velocity of 600m/s. A coating powder is injected into the plasma beam created and in the process is heated to 2,500°C so that it melts. In addition, the now liquid coating powder is accelerated to a velocity of up to 150m/s. Finally, the particles contained carried by the plasma beam strike the cylinder wall where they penetrate into the surface irregularities. Subsequently, the layer applied hardens, forming a positively interlocking junction between the coating and the cylinder wall. Finally, the inner surface of the cylinder is finished by means of a special honing process.CoatingDirection of burner rotationCoating powderPlasma gasBurner626_027Cylinder wallPlasma beamArcAlusil® process For this process, it is an essential requirement that the cylinder block is made of an aluminium-silicon alloy with a high silicon content. The cylinder blocks are manufactured using the lowpressure gravity die-casting method. This involves the molten metal being introduced into the re-usable mould (sometimes called a permanent mould) through a riser pipe, usually from below, using compressed air. From the beginning of the casting process close attention is paid to ensuring that silicon crystals form in the area of the cylinder walls in particular. This can be achieved by cooling the mould in the area that will ultimately form the inner surfaces of the cylinders. Increasing the silicon content in the walls of the cylinders makes those areas especially resistant. Afterwards, the inner surfaces of the cylinders are finished by means of a special honing process. And finally, the surface is enhanced by an electrochemical pickling process. The pickling removes the soft aluminium surrounding the silicon crystals. That further increases the resistance of the inner surface of the cylinder.626_028 16 BackForwards Ξ ContentsSurface finishing by honing The cylinder inner surfaces of both plasma-coated cylinder blocks and those made using the Alusil® process have to be machinefinished. This involves a fine surface texture being ground into the cylinder contact surfaces by a honing process. That finely textured surface provides better adhesion for the film of oil that provides the lubrication for the moving piston than an unfinished surface would provide. The surface textures produced differ according to whether the surface has been plasma-coated or produced using the Alusil® process.Honing plasma-coated cylinder surfaces The honing of plasma-coated cylinder walls is performed as the last operation before the pistons are installed. So that the coating applied is not removed by the honing process, a special honing method has been developed which creates minute recesses in the surface. Known as micro-pressure chambers, they are already present in the applied coating and are simply opened up by the honing process. The oil is held inside those recesses. When the piston ring then passes over one of those micro-pressure chambers, it produces pressure inside the chamber that acts against the piston ring. As a result, the piston ring floats on a cushion of oil, thereby perceptibly reducing friction and wear.Honed cylinder wall Piston ringOilPiston ringOil cushion626_029Honing cylinder walls manufactured by the Alusil® process With this type of cylinder block, the honing of the cylinder walls is performed as the penultimate operation before the pistons are installed. It is then followed by electrochemical pickling of the cylinder surfaces. The cylinders are honed using a hydraulically pre-tensioned hone. In the process, honing stones grind a fine texture into the cylinder surface. That texture subsequently retains the oil and guarantees sufficient lubrication.Honed cylinder wall Piston ring OilPiston ringOil626_030 17 BackForwards Ξ ContentsCrankshaftThe crankshaft is in the lower part of the cylinder block. The connecting rods are coupled to it. This enables the reciprocating motion of the piston to be converted in rotary motion. That produces the torque that is required to power the vehicle.DesignThe main journals are aligned on a common axis and run in the main bearings which locate the crankshaft in the cylinder block. The main bearings are bolted to the cylinder block from below and also from the side to provide additional stability and smoothness. The crankpins receive the big end bearings. The shaft journals and crankpins are connected to each other by a crank web. A counterweight opposite the crankpin equalises the inertial masses of the crankpins and crank webs. Balancing holes are drilled to balance out any differences in weight. Oil supply passages for lubrication of the big end bearings run from the shaft journals to the crankpins. In addition, there is a flange on the flywheel end to which the flywheel is attached.Oil boreCrank webMain journalFlangeFlywheel end626_031Cylinder blockCounterweightCrankpin Side bolting Main bearingBolting from below626_196ManufactureCrankshafts can be cast or forged. The two manufacturing methods produce crankshafts with different properties. A comparison of the properties of the two types shows why forged crankshafts are increasingly being used.Cast crankshafts Advantages: • Low manufacturing costs • Simple machining • Low weight Disadvantages: • Low rigidity • Poor vibration characteristics • High wearForged crankshafts Advantages: • High rigidity • Good vibration characteristics • Low wear Disadvantages: • Higher manufacturing costs • Complex machining • High weight18 BackForwards Ξ ContentsSplit crankpinsIn V and W engines, pairs of opposing pistons are attached to a common crankpin. So that this arrangement does not adversely affect the smooth running characteristics of the engine, the firing intervals between the cylinders have to be precisely matched. Such fine tuning can be achieved by the used of offset or "split" crankpins. The crankpin offset is definitively determined by the cylinder bank angle. For a cylinder bank angle of 90°, split crankpin crankshafts with an 18° crankpin offset are used. This achieves an even firing interval of 72° of crankshaft rotation. Split-crankpin crankshafts are usually forged. The reason for that is that forged crankshafts are significantly more rigid and offset crankpins are subject to enormous forces acting on the junction of the offset. That junction point is therefore more susceptible to breakage in operation. For that reason, the crankshaft journals are roller burnished at the junction with the crank web. The compression of the material increases the strength of the crankshaft.JunctionSplit crankpin626_032Scan the QR code to watch a short video about roller burnishing.Design of centre main bearingThe job of the crankshaft bearings is to locate, support and guide the crankshaft in the crankcase. To minimise wear, they should offer as little friction as possible when doing so. Different bearing shells are used in the crankshaft main bearings according to the engine design. One type is the triple-layer composite bearing. It is distinguished by exceptionally high wear-resistance and enormous load-bearing capacity. The crankshaft is axially retained in the centre main bearing by crescent-shaped thrust washers. Triple-layer composite bearings consist of a steel backing shell, a thin substrate layer and the actual bearing contact layer. An oil groove with integral bore provides for lubrication of the main bearing.Steel backing shellContact surface layer (0.012 - 0.02mm) Nickel barrier (0.001mm) Substrate layer (0.2 - 0.3mm) Oil supply626_033 Scan the QR code to find out more about the crankshaft in a V12 engine.19 BackForwards Ξ ContentsVibration damper (illustrated on the 4.2l V8 TDI engine)Because of the play in the crankshaft drive gear, if high rotational forces are abruptly released, the entire system can be caused to vibrate, which – as well as producing noise – can also lead to mechanical damage. That is one reason why prompt damping of rotational vibration is very important. The important aspect with this type of vibration damping is that the inertia ring has a high mass. In addition, it should have a large diameter so that it is as far out as possible. In contrast with the flywheel, for example, this inertial mass is attached to the rotating component to be damped by a rubber damper. In the illustration below, the inertial mass at the rear of the damper is attached to the rubber layer and that in turn is fixed to the poly-V belt pulley at the front by vulcanising. This allows the inertial mass to rotate relative to the not entirely even rotation of the crankshaft. The belt pulley on the crankshaft is fitted with a vibration damper. In order to damp the vibration of the poly-V belt arising from the uneven acceleration rates of the pistons during combustion, a freewheel in the alternator and an additional damping idler have been fitted. The vibration damper is designed in such a way that the torsional forces occurring at medium engine speeds are about 13% lower than with a belt vibration damper. This results in lower stresses on the crankshaft and improved engine noise characteristics. The belt drive system drives the alternator and the air conditioning compressor.-13 Torsional force, amplitude in Nm Rotational vibration damper Belt vibration damper100015002000250030003500400045005000626_224Engine speed (rpm)Additional damping idlersCounterweight to crankshaftFreewheel on alternator626_225Rubber layer20Belt track BackForwards Ξ ContentsVibration damper (illustrated on the 4.0l V8 TFSI engine)The viscous-coupling damper reduces rotational vibration. Such vibrations are caused by the gas-pressure and inertial forces (internal combustion and rotating and oscillating masses) that occur in an internal combustion engine. The vibrations cause relative movement between the housing and the inertia ring. Nowadays there are vibration dampers that have an outer cavity ring filled with silicon oil. They are able to react even more quickly to uneven crankshaft rotation. The silicon oil in the damper is subjected to shear stress. Those stresses act on the entire surface in the space between inertia ring and housing. The combined stresses produce the damping effect.HousingBearing components Inertia ringSilicone oilCover626_226Viscous-coupling vibration damper (illustrated on the 5.2l V10 FSI engine)The V10 FSI engine is fitted with a viscous-coupling damper, for which proximity to the vibration source is an important aspect. A ring in the belt pulley is filled with a highly viscous oil, which acts as the damping fluid. That high-viscosity oil damps the relative movement of damping element and vibration damper housing.Poly-V belt trackCounterweight to crankshaftVibration damper housingDamping elementCover plateLocating pin626_227 21 BackForwards Ξ ContentsPistonThe pistons are fundamental components of any reciprocating engine. They fit and move up and down inside the cylinders and seal off the combustion chamber from the cylinder block. They take up the gas pressure resulting from combustion and transfer it via the connecting rods to the crankshaft as a rotational force. In the process, the pistons are subjected to extremely high thermal and mechanical stresses.Requirements placed on the pistons: • • • • • • High strength Corrosion-resistance Smooth running characteristics Low weight Low oil consumption Low emissionsAreas of a pistonFire landThe fire land protects the top piston ring against overheating. A rounded inner fillet optimises heat dissipation and makes the piston crown more rigid.Ring landThe ring lands are the sections of the piston between 2 ring grooves. The top ring land in particular is subjected to high stress by the combustion chamber pressure. To prevent ring land breakage, this ring land must therefore be designed to be especially resistant. The height of the top ring land relative to the piston diameter varies according to the type of engine (see table).Engine type Petrol engine Diesel engine Diesel engine with turbochargerHeight of top ring land relative to piston diameter 4,5 - 5 % 6 % 7 - 8 %Gudgeon pin bossThe gudgeon pin boss serves to retain the gudgeon pin. It is the point at which the piston force is transferred to gudgeon pin.22 BackForwards Ξ ContentsStresses• Ignition pressures of 50 - 180bar on the piston crown and combustion recess. • Lateral forces on piston skirt. • Surface pressure on piston boss. • Acceleration of up to 25,000m/s2. • Dynamic friction on the piston skirt and gudgeon-pin bearings. • Piston tilt • Temperatures: • Piston crown/recess edge: 200°C - 400°C • Gudgeon-pin boss: 150°C - 260°C • Piston skirt: 120°C - 180°CPiston crownThe piston crown forms the combustion chamber together with the cylinder and the cylinder head. Its shape is determined by the valve configuration and engine design. Thus in FSI engines, for example, the piston crowns are shaped so as to deflect and thereby optimise the air flow.Piston ringsThe piston rings dynamically seal off the combustion chamber from the cylinder. The zone of a piston in which the piston rings are located is called the piston ring zone. The height of the piston ring zone is determined by the number and size of the piston rings fitted. Most pistons have 3 piston rings – 2 compression rings and 1 oil scraper ring.Piston skirtThe piston skirt serves to keep the piston straight inside the cylinder. It also transfers the lateral forces to the cylinder wall. A long piston skirt and a tight fit counteract piston tilt. In order to reduce wear of the piston skirt surface, it is coated by a special process, see page 25.626_03623 BackForwards Ξ ContentsSpecial features of diesel engine pistons The pistons of a diesel engine differ in design from those of a petrol engine. Diesel engine pistons have a piston crown recess in which the injected fuel mixes with the intake air. For that purpose, the recess is matched to the position of the fuel jet from the fuel injector.Piston crown recess Annular oilwayPiston cooling Depending on the particular design, the pistons may also have an active cooling system. This technology is used to minimise the temperature in particularly highly stressed areas such as the piston crown or the ring zone. There is an oil ring channel inside the piston for the purpose which is supplied with engine oil by a piston cooling jet and so cools the piston crown. The oil ring channel is formed by a salt core insert during the casting process.Piston cooling jetPiston dimensions626_037The character of a piston is definitively determined by its geometry and the associated dimensions.234 15 7 68626_038Number1Definition Compression height Piston diameter Maximum diameter of crown recess Crown thickness Crown diameter Lower length Skirt length Overall lengthDefinition Specifies the distance between the centre of the gudgeon pin and the top edge of the fire land. Specifies the diameter of the piston crown. Specifies the maximum diameter of the crown recess. Specifies the thickness of the piston crown. Specifies the diameter of the piston crown. Specifies the distance between the centre of the gudgeon pin boss and the bottom edge of the skirt. Specifies the length of the piston skirt. Specifies the overall length of the piston.2 3 4 5 67 824 BackForwards Ξ ContentsOffset of piston hub boreThis refers to the offset of the gudgeon pin axis from the piston centre-line. This has a decisive effect on piston slap forces thereby optimising the contact characteristics when the force changes from on side to the other. The result is a reduction in piston noise. In addition, the occurrence of damage to the cylinder liners, known as cavitation damage, can be minimised.Piston installation clearanceWhen fitting a piston in the cylinder, the installation clearance has to be taken into account. The installation clearance is the difference between the cylinder diameter and the piston's maximum diameter. The figure may be marked on the piston crown. The piston's installation orientation will also be indicated. It is absolutely imperative that the installation orientation is served.ManufactureThe way in which pistons are made differs according to their type. They are manufactured by different processes according to their intended use and the associated stresses. Common to all piston designs is that they undergo a surface treatment process after manufacture. That minimises wear and improves running characteristics. Some pistons are provided with a ferroprint coating on the piston skirt for that purpose.Production methods: • Forging • Pressing • Casting • Gravity die casting • Spin casting • Continuous casting • Squeeze castingTypesDifferent types of engine demand the use of different types of piston. The essential differences are in the shape, material and structure of the piston. The most obvious differences are in the geometry of the piston crown and recess. The illustration below shows a few of the possible piston designs.TDI engine with piston recessV8 TFSI engine with valve recessesFSI engine for stratified charge operationW12 engine with slanting crown626_039626_041626_042626_040Ferroprint coatingScan the QR code to find out more about the function of the piston crown in a diesel engine.25 BackForwards Ξ ContentsRegulating pistonThe term controlled-expansion piston is used to refer to pistons that have precisely directed/controlled thermal expansion properties. They contain a steel brace cast integral with the alloy piston that directs the thermal expansion in a specific direction. If we compare a controlled-expansion piston when hot and when cold, it is evident that the steel brace works in conjunction with the piston alloy to produce a bi-metal effect. This directs the thermal expansion mainly in the direction of the gudgeon pin axis. To allow for the expansion of the piston, the area around the gudgeon pin is made slightly oval in shape.Cast integral steel braceEngine coldEngine at operating temperature626_043626_044Flow deflectorThe pistons of direct-injection petrol engines have crowns that are specially shaped so as to influence the gas flow within the combustion chamber. As well as flow deflectors, some of them have injection recesses which play an particularly important role in what is known as stratified charge operation.Flow deflector Injection recess626_04226 BackForwards Ξ ContentsPiston ringsThe piston rings are in the upper part of the piston. A distinction is made between compression rings and oil scraper rings. The compression rings are always above the oil scraper ring.Piston ring Compression ringFunction • Forms a between the piston and the cylinder • Dissipates heat from the piston to the cylinder wall • Wipes off the excess oil from the cylinder wall • Returns the wiped off oil to the sumpOil scraper ringManufacturePiston rings have to withstand enormous stresses due to the high piston speeds and high pressures in the cylinder. Therefore, piston rings are made of cast iron or high-alloy steels. Pistons subjected to especially high stresses have cast integral high-strength ring groove inserts for holding the upper piston rings. Ring groove inserts are used primarily in diesel engines but are also occasionally found in FSI engines.Ring groove insert (cast integral)Compression ringsOil scraper ring626_036TypesThere are various types of piston ring according to the engine design and intended use. Piston ring Compression rings Profile Designation Plain rectangular compression ring Tapered piston ring Features and advantages Easy to manufacture.Shortens the time it takes to run-in a new engine.Trapezial ringPrevents the ring sticking inside a ring groove filled with coking residue. The low tension of the ring allows the combustion gases to penetrate behind the ring and so increase the contact pressure against the cylinder wall. Extra oil scraping effect.L-ringOil scraper ringsStepped ringSlotted oil scraper ring Coil-spring-loaded oil control ringOil scraping action with additional slot to allow oil to pass into inside of piston. Improved oil scraping effect due to higher contact pressure.27 BackForwards Ξ ContentsGudgeon pinThe gudgeon pin forms a frictional joint between the piston and connecting rod and has to withstand enormous loads in performing its function. Due to the reciprocating motion of the piston, the gas pressures and inertial forces that occur, and the difficult lubrication conditions, a whole series of demands are placed on the gudgeon pins.Requirements placed on gudgeon pins • • • • • • Low weight High rigidity High alternating-stress resistance and resilience of the material High surface quality Very hard surface High dimensional stabilityGudgeon pin designIn most engines the gudgeon pins are tubular and run in floating bearings. The pins are held in place by a circlip. On some engines the gudgeon pins are fixed in the connecting rod by shrink-fitting. To increase the strength of the piston, some engines such as the V6 TDI biturbo with twin turbochargers, have coated gudgeon pins. The coating enhances the low-friction properties of the gudgeon pin and reduces friction in that area. The use of sleeves with a contoured bore ensures that the pressure is evenly distributed between the gudgeon pin and the piston. The bore is shaped in such a way that it counteracts the deformation of the piston when the engine is running and thus ensures that the gudgeon pin is able to move easily.Sleeve with contoured boreGudgeon pinGudgeon pin retention626_052Gudgeon pin retentionIf the gudgeon pin is not held in the connecting rod by shrinkfitting, it has to be held in place to prevent it moving sideways and coming into contact with the cylinder wall. This is achieved in the majority of cases by internal circlips or snap rings made of spring steel. They locate in grooves in the outer ends of the gudgeon pin boss.Types of circlip626_05328 BackForwards Ξ ContentsConnecting rodThe connecting rods are attached to the bottom of the piston. They connect the piston and crankshaft and act together as a thrust rod. Their main task is to convert the linear (translational) movement of the piston into a rotational movement of the crankshaft. When in operation they are subject to pulling and pushing forces that alternate continuously and therefore also thermal stresses due to friction and combustion.DesignThe connecting rod shank is the central element. This is usually manufactured as a double T form. At the top end of the connecting rod shank is the "small end" with integral small-end bush. The small end holds the gudgeon pin, which is lubricated by oil splash. At the bottom end of the connecting rod is the "big end", the two halves of which are held together by stretch bolts. Two bearing shells in the big end form the bearing between the connecting rod and the crankpin.DesignWith the limited space available and ever-increasing compression pressures, the demands placed on connecting rods are very high.Trapezial connecting rod A piston with trapezial attachment in conjunction with a matching trapezial connecting rod satisfies both requirements. The contact area between the small end and the gudgeon pin is significantly larger compared with conventional piston-connecting rod combinations. This improves the distribution of combustion forces and significantly reduces the load on the components.Parallel connecting rodParallel small-end bush Small end same width at top and bottomTrapezial small-end bush Small end narrower at the top than at the bottom Web thicknessConnecting rod shankShoulder Flange thickness Connecting rod shankShoulder Top bearing shell Top bearing shellBottom bearing shellBig-end bearing cap with stretch boltsBottom bearing shellBig-end bearing cap with stretch bolts626_197626_057 29 BackForwards Ξ ContentsDiagonally split connecting rod Some V engines use diagonally split connecting rods. This design allows the connecting rod shank to be installed through the cylinder bore without the connecting rod cap.626_060Connecting rod shankBig-end bearing capManufactureConnecting rods are most commonly manufactured by the forging process. Various materials are used to manufacture this element and a range of corresponding manufacturing processes therefore also exists. The subsequent machining and the splitting of the big end are of particular importance. It is a case of ensuring as accurate a fit as possible, something that can be achieved very successfully with cracking. In the cracking process, a laser beam creates a predetermined breaking point on the connecting rod at which the connecting rod is subsequently split. A special splitting tool then performs the precision splitting operation. This produces a unique fracture surface. Both parts fit together in only one position. This technology has significant advantages when compared to cutting: • High-precision fit • Good frictional joint properties • No additional centring means required • More economical manufacture due to use of less material.Fracture surfacePredetermined breaking point626_061Big end bearingsThe crankpins are machined so as to achieve a precise fit with the bearing shells.Note To help identify the cause of knocking sounds, the combustion pressure can be reduced by disconnecting the spark plug lead or injector lead (on diesel engines) for a particular cylinder. That will allow the possibility of big-end bearing damage to be investigated on the cylinder concerned.30 BackForwards Ξ ContentsTiming belt drive systemOne of the ways in which the camshafts can be driven is by a toothed timing belt. Such a camshaft drive system uses a plastic drive belt to connect the camshafts to the crankshaft. A tensioner pulley ensures that the belt is always tensioned and so functions reliably. The timing belt drive system can also incorporate and drive other auxiliary units such as the coolant pump. A raised flange on the tensioner/guide pulley prevents the timing belt from running off the edge of the pulley.Requirements placed on timing belt drive system: • • • • • Long service life Minimal space requirements Very light weight Low noise properties Compliance with minimum wraparound requirements on the belt sprockets • Slack runs1) must be within the range 75mm - 130mm. • Timing belts must be guided by at least one pulley.Camshaft sprocketGuide pulleyHigh-pressure fuel pumpTiming beltTensioner pulley with lateral guidesCoolant pumpGuide pulleyCrankshaft626_0791)The slack runs are the lengths of the belt between the pulleys.Note If there are noises from the area of the timing belt, the tension of the timing belt should be measured with a belt tension gauge. In addition, the condition of the tensioner and guide pulleys should be examined. When examining the timing belt drive system, pay attention to the guidance in the workshop manual.31 BackForwards Ξ ContentsStructure of a timing beltA timing belt is made up of several layers.Advantages: • • • • • • • Low mass Quiet running characteristics Low production costs Requires no lubrication Simple drive system Versatile in terms of belt guidance Low frictionDisadvantages:626_080Rubber base material Polyamide tooth coatingPolyamide backing fabric Glass-fibre tension cords• • • • Possible for belt to jump or tear. Oil-free environment essential. Strictly specified bending radii. If a used belt is refitted, it has to rotate in the same direction as before. • Replacement intervals must be observed.Belt tensioning systemsBelt tensioning systems ensure that the belt is correctly tensioned and therefore functions reliably. There are 3 different types of tensioning system: • Eccentric tensioner pulley • Compact mechanical tensioner • Hydraulic tensionerEccentric tensioner pulleyCompact mechanical tensionerHydraulic tensionerMethod of operation Properties• Fixed tensioner pulley• Friction-damped tensioner pulley • Prevents belt stretching and wearing over time. • Reduces timing belt wear.• Hydraulically damped tensioner pulley • Timing belt is tensioned by a pressure spring in the hydraulic element via a lever and tensioner pulley. • Directional damping provided by means of a hydraulic element. • Directional damping enables control of complex belt drive systems. • Tensioning force is optimised.• Tension of belt varies according to engine temperature • Belt stretches and wears over time. • Belt gradually loses basic tension.32 BackForwards Ξ ContentsChain drive systemAnother means of driving the camshafts is by a chain drive system. This concept is adopted if greater forces need to be transmitted or larger distances need to be overcome. In this type of system, a chain transmits the rotation of the drive sprocket on the crankshaft to the camshaft sprockets. A hydraulic chain tensioner ensures that the chain is kept at a constant tension. The chain tensioner plays an essential role in minimising chain wear. Plastic guide rails guide the chain and minimise chain noise. Several chain tensioners may be used depending on the routing and length of the chain. The number of chain drive systems also varies according to the type of engine and the number of auxiliary units to be driven. Chain drive systems for auxiliary units are often tensioned by mechanical tensioners.Exhaust camshaft sprocketInlet camshaft sprocketChain drive systemGuide railTensioning railHydraulic chain tensionerCrankshaft sprocketBalancer shaft chain drive systemOil pump chain drive systemMechanical chain tensioner626_085Scan the QR code to find out more about the chain drive system.33 BackForwards Ξ ContentsComplex chain drive systemsThe number of chain drive systems used can vary according to the complexity of the engine and the number of auxiliary units to be driven. Complex chain drive systems are found primarily on V and W engines.Chain stretch Chain stretch can occur in chain drive systems. Its outward signs are noise from the chain drive system or loss of power. In such cases, the chain should be checked for stretching using the chain stretch gauge T40182.Chain drive system BChain drive system CChain drive system ABalancer shaft sprocketChain drive system D Regulated flow oil pump626_089Direction of travelNote When examining the timing chain drive system, pay attention to the guidance in the workshop manual.34 BackForwards Ξ ContentsChain designsDifferent types of chain are used according to the demands placed on the chain drive system. They can be subdivided into roller chains, bushed chains and inverted-tooth chains.Inner platesRoller chains The chain links of a roller chain have inner and outer plates. The two types of plate form the framework of the chain links. Pins join the inner and outer plates of a chain link together. They also join the chain links to one another. The pins fit inside bushes and the bushes in turn fit inside rollers. The rollers rotate around the bushes as they make contact with the sprocket teeth. This means that different parts of the circumference are used again and again. The lubricant between the rollers and sleeves helps reduce noise and has a damping effect.Outer platePin BushesRollers626_090Bushed chains The design of a bushed chain differs from a roller chain only by virtue of the absence of the rollers. With this type of chain, the teeth of the sprockets always make contact with the same point on the fixed bushes. That is why lubrication is especially important with this kind of chain drive system. Bushed chains are subject to less wear in the link joints.Inverted-tooth chains The inverted-tooth chain is a particularly efficient type of chain. The forces are transmitted by inverted-tooth plates. They are arranged back-to-back in several offset layers. Lateral guide plates prevent the chain from running off. Compared with conventional roller or bushed chains, inverted-tooth chains have significant advantages.Inverted-tooth plate Guide plateAdvantages: • • • • • • Require less space. Low wear Long service life No maintenance required. Capable of transmitting high forces. High speeds possible.Disadvantages: • • • • Noisier in operation Heavier Requires lubrication Complex covers required626_09135 BackForwards Ξ ContentsChain tensioning systemsChain tensioning systems perform a variety of tasks within the timing gear. The main task is to keep the timing chain tensioned on the slack side in all operating conditions under a defined load. Even if the chain stretches due wear in operation, that tension must be kept constant. Chain tensioners have damping elements to reduce vibration. On some engines the chain tensioning systems are provided with sector gears for safety reasons. They prevent the chain tension slackening if the engine oil pressure is too low. If the chain tension is too low, the chain could jump on the sprocket and thus cause damage to the engine. Chain tensioning systems are subdivided into pusher and puller-type systems.Pusher-type chain tensioning systems With this type of tensioning system, the timing chain is pressed outwards from the inside to tension it.Pusher-type chain tensioner626_104Puller-type chain tensioning systems In this case, the tensioning system pulls the timing chain inwards from the outside to tension it.Puller-type chain tensioner626_105 36 BackForwards Ξ ContentsBalancer shaftsVarious forces and torques are at play when an engine is running. They cause the engine to vibrate and, therefore, decisively determine how smoothly the engine runs and the stresses to which components are subjected. If the vibrations are transmitted to the bodywork due to inadequate engine mountings, they also substantially diminish ride comfort. The forces occurring during engine operation are classified as first-order or 2nd-order forces. Firstorder forces are inertial forces produced by centrifugal forces acting on rotating parts. The crankshaft can completely counterbalance such forces by means of the crankshaft counterweights and throw. The 2nd-order forces, on the other hand, have to be balanced out by special means. This category comprises forces that are produced by translational motion of the crankshaft drive gear components. A possible countermeasure that can be employed is the use of balancer shafts. The balancer shafts are usually driven directly by the crankshaft via a combination of gears or a chain drive system. They rotate at twice the speed of the crankshaft, with one of the balancer shafts rotating in the same direction as the crankshaft and the other being rotated in the opposite direction by means of an idler gear.Vibration balancing by 2 balancer shaftsBalancer shaftsGuide rail Gearing sprocket Tensioning rail Hydraulic chain tensioner Inverted-tooth chain Sprocket Guide rail626_145Vibration balancing by a central balancer shaftCentral balancer shaftChain drive system with guide sprocket for changing direction of rotation626_140Note Balancer shafts have to be fitted the right way round in the chain drive system.37 BackForwards Ξ ContentsBalancer shaft moduleThe balancer shafts may be fitted directly in the cylinder block or incorporated in a separate balancer shaft module. Balancer shaft module on EA288 On the EA288, a balancer shaft system positioned above the crankshaft in the cylinder block is used. The drive is delivered via helical gears running off the crankshaft. The shafts and the idler gear are held radially and axially by roller bearings. The bearings are lubricated by oil spray from the cylinder block.Roller bearingBalancer shaft 2Roller bearingBalancer shaft 1Crankshaft626_198Idler gear for direction reversalDesign On the 2.0l RDI engine, for example, the balancer shaft module is mounted below the crankshaft in the sump. It is driven by a system of gears running off the crankshaft. The module consists of a housing made of cast iron, 2 contra-rotating balancer shafts, the helical-gear drive system and the integral duocentric oil pump. The rotation of the crankshaft is transmitted to the idler gear on the outside of the housing. The idler gear transmits the drive to balancer shaft 1. Th