TECHNICAL DOCUMENTATION
SSP 633 Audi Q7 (type 4M) Chassis

This PDF is currently unavailable.
Read document text
Self Study Programme 633 For internal use onlyAudi Q7 Chassis(type 4M)Audi Service Training BackForwards Ξ ContentsSuspension system - overall conceptThe new Audi Q7 is a comfortable companion. It tracks smoothly and confidently on the motorway and spoils its passengers with a high level of rolling comfort. On twisting country roads, it is manageable, precise and agile, and it also keeps going when the asphalt stops. Compared with the previous model, the center of mass of the big SUV has been lowered by 50 mm, in part by installing the engine lower. The chassis also features numerous changes. Both the front and rear axles are five-link designs, replacing the double wishbone axles of the previous model. The new elastomer bearings and the separate springs and dampers at the rear axle respond very sensitively. The new electromechanical power steering with servotronic function is very efficient. It provides for direct steering response, and several of the new driver assistance systems would not be possible without it. Compared with the previous model, the chassis of the new Audi Q7 is over 100 kg lighter. The links of the wheel suspensions, for example, are now made of aluminium and high-strength steel. The front axle prop shafts are hollow, and the pivot bearings are aluminium forgings. Audi offers another groundbreaking innovation as an option: all-wheel steering. The new Audi Q7 already offers excellent comfort even with the standard steel suspension. Rolling is even smoother with the adaptive air suspension, which is managed by a newly developed central vehicle control unit that drives all body control systems. The new controllers developed by Audi for the air suspension and active damping vary the body height and body comfort as a function of the situation. The new Audi Q7 comes as standard with 18-inch wheels and 255/60 tires. Audi and quattro GmbH offer a large number of additional wheels in sizes up to 21 inches as options. Large, vented brake discs bring the SUV safely to a stop. They are gripped up front by aluminium six-piston calipers. The electromechanical parking brake, updated with convenient hill hold and startup functions, acts on the rear wheels. An electronic hill descent assist complements the wealth of equipment. New ESC and ACC generations provide the basis for a number of driver assistance systems.633_001633_001quattro all-wheel drive as standard with all Audi Q7 chassis. The following chassis versions are offered: Standard chassis (production control number 1BA) The standard suspension as basic equipment features steel springs and unregulated damping. Chassis with air suspension and electronic damper control (adaptive air suspension, 1BK) This chassis version is optional.Sport chassis with air suspension and electronic damper control (adaptive air suspension, 2MA) The sport chassis with air suspension is optional too.2ContentsAxles and chassis alignmentFront axle _____________________________________________________________________________________________________________________________________________________ 4 Rear axle ______________________________________________________________________________________________________________________________________________________ 6 Chassis alignment / setup _ __________________________________________________________________________________________________________________________________ 8Chassis with air suspension and electronic damper control (adaptive air suspension)Overview ______________________________________________________________________________________________________________________________________________________ 9 Design and function _ _______________________________________________________________________________________________________________________________________ 10 System function _____________________________________________________________________________________________________________________________________________ 14 Operation and driver information _________________________________________________________________________________________________________________________ 19 Service operations _ _________________________________________________________________________________________________________________________________________ 20Brake systemOverview _____________________________________________________________________________________________________________________________________________________ 22 Wheel braking systems _ ____________________________________________________________________________________________________________________________________ 22 Brake servo, master brake cylinder, pedal assembly ____________________________________________________________________________________________________ 24 ESC ___________________________________________________________________________________________________________________________________________________________ 25Steering systemOverview _____________________________________________________________________________________________________________________________________________________ 27 System components and operation _______________________________________________________________________________________________________________________ 28All-wheel steeringOverview _____________________________________________________________________________________________________________________________________________________ 29 Technical implementation _ ________________________________________________________________________________________________________________________________ 32 System components ________________________________________________________________________________________________________________________________________ 33 Function of the overall system _ ____________________________________________________________________________________________________________________________ 35 Basic function _ ______________________________________________________________________________________________________________________________________________ 36 Additional functions/special operating states ___________________________________________________________________________________________________________ 36 Operation and driver information _________________________________________________________________________________________________________________________ 37 Service operations _ _________________________________________________________________________________________________________________________________________ 38Adaptive Cruise Control (ACC)System overview ____________________________________________________________________________________________________________________________________________ 39 Design and basic function of system components _______________________________________________________________________________________________________ 40 Design and function of system components _____________________________________________________________________________________________________________ 42 Service operations _ _________________________________________________________________________________________________________________________________________ 50Wheels and tyresOverview _____________________________________________________________________________________________________________________________________________________ 51 Low tyre pressure indicator ________________________________________________________________________________________________________________________________ 52 Tyre pressure monitoring system _ _________________________________________________________________________________________________________________________ 52The Self Study Programme teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a Repair Manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. This content is not updated. For further information on maintenance and repair work, always refer to the current technical literature.NoteReference3 BackForwards Ξ ContentsAxles and chassis alignmentFront axleThe front axle is based on the modular longitudinal platform (MLB). The Audi Q7 adopts the tried and tested five-link axle concept already used on other Audi models.Spring −− Steel spring with linear characteristicGuide link −− Forged aluminium designDamper −− Twin-tube shock absorber with additional polyurethane spring −− Tailored to Q7 −− Low-friction axial bearings for upper strut mountings (new development) Suspension strut knuckle −− Cast aluminium design −− Bolted to support linkJoint −− The control arm/pivot bearing are connected by a spherical joint −− Aluminium housingEngine/gearbox mount −− Welded aluminium design with cast nodes and IHU profilesAnti-roll bar −− Tubular anti-roll bars −− Vulcanised bearing elements4 BackForwards Ξ ContentsCross strut −− Steel construction −− bolted to subframe to increase stiffnessUpper link −− Forged aluminium design −− Mounted directly to body without a separate bearing pedestalPivot bearing −− Forged aluminium design −− 2 axle load dependent versions (wheel bearing width)Tie rod −− Aluminium housing with rubber-metal bearingsWheel bearing −− 2nd generation wheel bearing −− 2 versions with different wheel bearing widths (40.5 mm and 42 mm) Wheel hub −− Steel construction633_002Support link −− Forged aluminium design5 BackForwards Ξ ContentsRear axleThe rear axle is also based on the modular longitudinal platform (MLB). The Audi Q7 features a newly developed five-link axle. By paying close attention to lightweight design, the weight of the axle has been reduced by 40 kg compared with the previous model.Track link −− Steel constructionSpring −− Steel springs with linear spring characteristicUpper rear wishbone 2 versions: −− Steel design (standard) −− Forged aluminium design for adaptive air suspension, rear axle steering and cars with "large" steel springs (high axle load)Lower front wishbone −− Steel constructionTie rod −− Aluminium extrusion profile with rubbermetal bearingsAnti-roll bar −− Tubular anti-roll bars −− Two-piece bearing cups, loose and bolted using steel clamps6 BackForwards Ξ ContentsEngine/gearbox mount −− Steel construction −− Flexible body attachment, achieved using rubber-metal bearings at rear and hydraulic bearings at front −− 3 versions based on axle load: load group 3, loud groap 4 and load group 4 with rear axle steeringDamper −− Twin-tube shock absorber with additional polyurethane springUpper wishbone −− Forged aluminium design −− Attachment of the anti-roll bar coupling rod and the linkage of the level control system sensorWheel carrier −− Aluminium casting −− 2 versions based on different wheel bearings Wheel bearing −− 2nd generation wheel bearing −− 2 axle load based versions (various outer diameters)633_003Spring link −− Shaped aluminium extrusion profile −− Attachment of spring and damper −− Concealed by aero trim in diagramAero trim −− Attached by clips to the spring link at the bottom −− Reduces liftBalancer weight −− Bolted to subframe −− Not visible in diagram7 BackForwards Ξ ContentsChassis alignment / setupThe left and right tracking values on the front axle can be adjusted separately by altering the length of the track rods. The camber can be centred within narrow limits by shifting the subframe transversely. Individual tracking values and individual camber values can be adjusted on the five-link rear suspension.Tracking adjustment at attachment point of track link and subframe (not shown in graphic)Tracking adjustmentCamber adjustment at attachment point of spring link and subframe (concealed by aero trim)Camberbalancing633_004Note Always adjust the rear axle camber first, then the tracking. This is important because the tracking values are altered slightly when the camber is adjusted.8 BackForwards Ξ ContentsChassis with air suspension and electronic damper control (adaptive air suspension)OverviewTwo aas chassis versions with a different configuration/setup are optionally available for the Audi Q7. They have production control numbers (PR number) 1BK "adaptive air suspension" and 2MA "adaptive air suspension sport". The system is based on the aas systems already used on other Audi models. A key new feature is the chassis control unit J775. This control unit contains the control software for the air suspension and damping systems, and will, in the future, also contain control algorithms for other chassis control systems. A high integration platform such as this makes it possible integrate the large number of chassis versions into an extended control unit architecture and, thus, to reduce the number of hardware variants in the vehicle. It is also possible to use a common hardware including the necessary safety concept for the miscellaneous chassis versions.Air spring strut with damper, front right Damping adjustment valve, front right N337Chassis control unit J775 −− contains the control software for the air suspension and damping systems as well as the sensors for measuring vehicle dynamicsDamping adjustment valve, rear right N339Pressure accumulatorAir supply system with compressor and solenoid valve blockDamping adjustment valve, rear left N338 Air spring Level control system sensor, rear left G76 Level control system sensor, front left G78 Pressure accumulator Air lines −− Polyamide tube Level control system sensor, front right G289 Air spring strut with damper, front left Damping adjustment valve, front left N336633_005Level control system sensor, front left G789 BackForwards Ξ ContentsDesign and functionChassis control unit J775 In the Audi Q7 and future models based on the modular longitudinal platform, the chassis control unit will function as a universal control unit for chassis control systems. The control unit in the Audi Q7 contains the suspension and damping control software developed by Audi. In addition, the sensors are integrated in the control unit to measure vertical acceleration (z), as well as the yaw rates about the longitudinal axis (x direction, squat and roll) and the transverse axis (y direction, pitch). The control unit is installed at the front end, below the air conditioner under the centre console. A FlexRay bus is used for communication.633_006Air supply unit The compressor with electric motor as drive and the solenoid valve block are mounted on a common bracket as a compact unit. The entire unit is attached to the vehicle's outer body at the rear right.The compressor / electric motor unit is additionally mounted to the bracket by spring elements. The bracket is vibration-isolated from the body at the mounting points by rubber mounts. The complete unit is protected against stone chip damage and other damage by a special cladding.Drive unit633_007CompressorElectric motorSolenoid valve block10 BackCompressor with electric motor A newly developed two-stage "twin" compressor is used to produce the requisite air pressure. The compressor is driven by an electric motor. A few feature is the mode of activation of the electric motor. Instead of using a mechanical relay, the motor is now activated by a cyclic pulse wave modulated (PWM) signal. This mode of activation allows for soft starting and stopping of the motor and reduces the peak load of the onboard power supply. The activation signal is processed by a special drive unit, which is also attached to the common bracket by clips. A separate bus (CAN bus) is used for data transfer between the chassis control unit and the drive unit.Forwards Ξ ContentsThe compressor compresses the air by means of 2 pistons. The piston of the 1st compression stage (smaller diameter) is connected directly to the eccentric plate of the drive shaft by its conrod. The piston of the 2nd compression stage (larger diameter) is mounted on the conrod of the 1st compression stage. As a result, both pistons move jointly in the same direction. While the 1st compression stage piston is compressing the air, the 2nd compression stage piston draws in air. The 1st compression stage produces a pressure of about 4-6 bar, while the 2nd compression stage piston delivers a system pressure of about 18 bar. The temperature and running time of the compressor are monitored on the basis of a temperature model. The maximum "on" time is about 4 min. The activation electronics also have a safety function which, in the worst case scenario, switches off the compressor after a maximum of 6 minutes.2nd compression stage piston633_0081st compression stage piston11 BackSolenoid valve block The solenoid valve block consists of five solenoid valves which connect the air supply unit to the air suspension and the pressure accumulators, or interconnect the air suspension and the pressure accumulators. A pressure sensor is integrated in the solenoid valve block.Forwards Ξ Contents633_0106789 1012 11 1 2 3 4 51413 Solenoid valve block633_0111-5 = 6,7 = 8,9 = 10 = 11 = 12 = 13 = 14 = solenoid valves air suspension, front axle air suspension, rear axle pressure accumulator pressure sensor pressure reading electrical activation of solenoid valves compressor connection The 2/2 way valves (1-5) in the solenoid valve block open or close the pathway to the pressure accumulators and the air suspension. The graphic shows the valves in a neutral state, i.e. not electrically activated. The valves are closed when de-energised. When required, the corresponding solenoid valve is activated in order to fill or exhaust the assigned air spring.The pressure sensor is arranged in such a way that it measures the pressure in the pressure accumulators or the pressure in the air suspension system, depending on the configuration of the solenoid valves.12 BackPressure accumulator For packaging reasons, the Audi Q7 has two separate pressure accumulators each with a capacity of 5 litres. The accumulator modules are installed in the rear footwell on the left and right hand sides of the vehicle and are interconnected by a line. They are made of aluminium. The pressure accumulators are primarily used for making corrective adjustments in order to enhance vehicle acoustics while the vehicle is stationary or driving at low speeds. When the vehicle exceeds a speed of approx. 30 kph, the pressure accumulators are filled and control operations are preferably implemented by producing pressure using the compressor. In general, control operations can only be implemented using the pressure accumulator if the accumulator pressure is at least 3 bar higher than the pressure in the air spring to be controlled.Forwards Ξ Contents633_012Front axle air spring strut The air spring seal is made of natural rubber with polyamide strength members. Its is attached to the damper tube at the bottom and to the damper bearing at the top by clips. The resultant enclosed space forms the air chamber. The air spring seal "rolls" over the roll piston when the springs compress and rebound. The geometric shape of the roll piston determines the spring characteristic. The minimal air pressure inside the chamber is limited to about 3 bar by a special valve (residual pressure retention valve) at the air connection. This protects the air spring seal against mechanical damage which can occur when the chamber is evacuated, particularly in the region of the rolling fold.Air spring seal Roll pistonBellows seal633_013Rear axle air spring The air spring seal is made of natural rubber with polyamide strength members. It is attached to the roll piston and the baseplate of the air spring by clips. The geometric shape of the baseplate and the upper part of the air spring define the installation position in the vehicle and provide protection against twisting.Air intake/ventilation To meet the acoustic requirements, a damper is used for air intake and air discharge from the system. The damper is installed in the rear end, where it is protected inside the vehicle in front of the right-hand wheel arch.Bellows seal Roll pistonAir spring seal633_015633_014 13 BackForwards Ξ ContentsSystem functionFilling the pressure accumulator2341 2 3 4 = = = = solenoid valve pressure accumulator compressor air intake1633_016When the vehicle exceeds a speed of approx. 30 kph, the pressure accumulators are filled. The solenoid valve 1 is activated and a connection is established between the compressor and pressure accumulator.Increasing ride height via pressure accumulator (using front axle as an example)1-5 6,7 8,9 10 7 8= = = = solenoid valves air suspension, front axle air suspension, rear axle pressure accumulator910612345633_017The pressure accumulators are primarily used for making corrective adjustments in order to enhance vehicle acoustics while the vehicle is stationary or when driving at low speeds. In general, control operations can only be implemented using the pressure accumulators if the accumulator pressure is at least 3 bar higher than the pressure in the air spring to be controlled.14The pneumatic diagram shows the valve configuration using an increase in ride height at the front axle as an example. Solenoid valves 1 and 2 in the solenoid valve block are activated and the compressor is not running (off). The air flows from the pressure accumulators 10 into air springs 6 and 7 via open solenoid valves 1 and 2. BackIncreasing ride height via compressor (using front axle as an example)Forwards Ξ Contents10 13121411678912345633_0181-5 6,7 8,9 10 = = = = solenoid valves air suspension, front axle air suspension, rear axle pressure accumulator11 12 13 14 = = = = 1. compression stage 2. compression stage solenoid valve for boost function air drierWhen the vehicle exceeds a speed of approx. 30 kph, control operations are preferably implemented by producing pressure using the compressor. For this purpose, the corresponding solenoid valves in the solenoid valve block are activated and the lines interconnecting the compressor and air suspension are opened. In the example given here, pressure is produced by the compressor with boost function in order to increase ride height at the front axle. The boost function is a major innovation which provides a rapid increase in pressure when required. The function uses the pressure accumulator pressure. The compressed air from the pressure accumulators flows into the intake tract of the 2nd compression stage on the compressor. This serves to increase the pressure of the 1st compression stage 11.The boost function is active whenever the pressure in the pressure accumulators is insufficient for control purposes, but is greater than 5 bar. If the pressure in the pressure accumulators drops below 5 bar during an active control phase, the control operation is not cancelled, but rather is completed. The boost function increases the capacity of the compressor. Without this function, the compressor would have to be much larger (and therefore also heavier). The solenoid valve 13 is activated in such a way that the compressed air from the pressure accumulators can flow into the intake tract of the 2nd compression stage on the compressor. Before leaving the compressor, the compressed air flows through the air drier 14, which extracts moisture from the air.15 BackLowering the ride height (using the rear axle as an example)Forwards Ξ Contents1210111314678912345633_0191-5 6,7 8,9 10 = = = = solenoid valves air suspension, front axle air suspension, rear axle pressure accumulator11 12 13 14 = = = = pneumatic switching valve solenoid valve air drier intake and ventilation connectionThe lines interconnecting the compressor and air suspension are opened by activating the solenoid valves 14 in the solenoid valve block. To allow the compressed air to escape from the air suspension, the pneumatic switching valve 11 must be opened. This is done by activating the solenoid valve 12. The solenoid valve opens and pressure is applied to the pilot connection of the pneumatic switching valve. The switching valve is switched to the open position.The air flows through this valve and leaves the system through the intake/ventilation connection. The dry air flows through the drier and extracts the moisture in the air from the system.16 BackControl strategy for chassis 1BK without trailer operation The control algorithms generally differ depending on the chassis versions. Differences also exist with regard to operation with and without a trailerForwards Ξ ContentsIn general, it is not permissible to reduce the vehicle level to the low setting when towing a trailer in order to avoid variation in the load on the tow bar.modeLevelLowering [mm]liftHigh level 10soffroadHigh level 2 12 s 0scomfort automatic dynamic Normal level 120 s 20 s 30 sLow level0sMotorway level30 s 0s20 sLoading levelSpeed [kph]633_020As an example, the control strategy outlined above is explained. In principle, the control system implements six different vehicle levels. Starting from the basic level, "offroad" mode can be set by raising the vehicle 25 mm. The mode is immediately deactivated automatically when the vehicle reaches or exceeds a speed of 80 kph. If the vehicle's speed is subsequently reduced to 35 kph, the vehicle level is automatically readjusted to "offroad" level. The maximum ride height (+60 mm) is achieved by activating "lift" mode. This mode is exited automatically when a speed of 30 kph is reached and "offroad" mode is activated. The basic level is used by two modes: "comfort" mode and "auto" mode. In "comfort" mode, suspension and damping are configured for maximum ride comfort. If a speed of 120 kph is reached, the ride height is lowered by 15 mm (vehicle level in "dynamic" mode) after 30 s, both in "auto" mode and in "comfort" mode.If the speed is again reduced, the basic level is restored after 20 s in "comfort" mode at 70 kph and after 120 s in "auto" mode. If a speed of 160 kph is reached after the vehicle level is reduced to dynamic level, the vehicle level is reduced by a further 15 mm (motorway level) in "auto" mode and in "dynamic" mode. If the driver subsequently reduces speed, the system returns to dynamic level after 30 s at 130 kph. The Audi Q7 also has a feature which assists loading. The rear end lowered by a further 55 mm relative to the basic level. If the loading level is not deactivated again by the driver, this is done automatically immediately after reaching a speed of 2 kph. The ride height is then readjusted to the last level set prior to loading.17 BackControl strategy for chassis 2MA (sports chassis) The basic ride height has been reduced by 15 mm compared to chassis 1BK. The ride height in "dynamic" mode has also been reduced by 15 mm compared to 1BK, and likewise the ride height is not lowered in "comfort" mode.Forwards Ξ ContentsmodeLevelLowering [mm]liftHigh level 10soffroadHigh level 2 (=DIN unladen) 1BA Normal level 0s12 scomfort automatic dynamic0s20 s30 sMotorway level0s30 s20 sLow level Loading levelSpeed [kph]633_02118 BackForwards Ξ ContentsOperation and driver informationDifferent suspension and damping control modes are implemented on the Audi Q7. They can only be set by selecting the relevant mode in Audi drive select. Depending on preference, the driver can choose between comfortable ("comfort"), sporty ("dynamic") and balanced ("auto") damping setups. Alternatively, the driver can select "offroad" mode for driving under offroad conditions or "lift" mode for even more difficult terrain. The rear end can be lowered in order to simplify loading and unloading. If "efficiency" is selected, the "auto" mode is activated. As usual, the individual setting combines various settings of different vehicle systems.Vehicle: Audi drive select633_022Lowering the rear end makes it easier to load the vehicle. Starting from the ride height in "auto" mode, the rear end is lowered by approx. 55 mm. Conditions for the activation of rear end lowering: • All doors are closed. • Terminal 15 "on" • The pressure accumulator is sufficiently filled. The function is operated using the push button in the luggage compartment. The rear end is again raised into the starting position by: • pushing the button. • selecting a different mode in Audi drive select. • exceeding a driving speed of approx. 2 kph. The status of the system is indicated to the driver by a warning lamp in the button. This lamp is lit while lowering is in progress and when the rear end is lowered. If the pressure in the pressure accumulator is too low, the warning lamp will briefly flash 3 times.633_022aSystem faults are indicated to the driver by the familiar yellow or red warning symbol in conjunction with a text message.Susp. control Fault! You can continue driving633_02319 BackForwards Ξ ContentsService operationsDiagnostic address The system can be accessed in the diagnostic tester under address 74 - suspension control. Control unit J775 is integrated in the component protection system. Coding is carried out online.Reprogramming the default suspension height After removing / installing or replacing the control unit, it is necessary to reprogram the default suspension height and to calibrate the sensors in the control unit on completion of encoding. This can be done by configuring separate basic settings on the diagnostic tester, but also by starting a complete cycle. The vehicle must be at rest (no persons in the vehicle with the doors closed) throughout the entire process. The process of programming the default suspension height begins by raising the vehicle on a hydraulic hoist and by moving the dampers into the access position. The measurement data supplied by the level control system sensors is evaluated and stored. The vehicle is then set down on its wheels again and automatically adjusted to a defined level by the control unit. With the vehicle in this position, the mechanic measures the heights and enters them into the diagnostic tester for each of the individual wheel positions. The control unit then adjusts the vehicle to the normal level within a close tolerance and activates the control system. The axle load is then calibrated automatically. After the normal vehicle level has been set, the sensors in the control unit are calibrated. For this purpose, the vehicle must be at rest on a level surface. On completion of calibration, all control options will be available.633_006The default suspension height is programmed after: • replacing the chassis control unit J775 • removing / replacing one or more level control system sensors • performing work on the chassis which involves detaching the lever of the level control system sensors on the axle carrier • replacing / removing and installing the dampers633_02520 BackActuator diagnostics The following actuator diagnostics routines are available: • Actuator diagnostics for lowering vehicle - Testing the air spring seal, hoses, level control system sensor for signal / adjustment direction • Actuator diagnostics for damper valve energisation - Electrical damper activation • Actuator diagnostics for system testing of boost function - Testing of solenoid valves for boost function • Actuator diagnostics for system testing of compressor pressure accumulator - Testing pressure buildup, compressor activation and pressure accumulator solenoid valveForwards Ξ Contents633_025bVehicle transportation To be able to transport the vehicle with air suspension fully evacuated, use is made of a new special tool - manoeuvring aid set VAS 741013. The tool is pushed under the vehicle in the position where the air suspension is evacuated so that one roller is in front of the wheel and the other behind it. The rollers are moved towards one another by operating the foot lever until the wheel is raised off the ground. The vehicle can then be moved on the rollers of the special tool and the other wheels. The 4 manoeuvring aids shown here belong to the set. Note: the vehicle must not be moved or driven under engine power using VAS 741013.Manoevring aid set VAS 741013Loading mode When the loading mode is activated, the high level is set in order to maximise ground clearance. The loading mode can be deactivated again using the diagnostic tester. Alternatively, the loading mode is deactivated automatically when the vehicle exceeds a speed of 100 kph or after travelling a distance of 50 kph.Transport mode When the transport mode is activated, no further control operations are performed and the damper control function is deactivated. The control function is restored when the engine is started.21 BackForwards Ξ ContentsBrake systemOverviewThe Audi Q7 is equipped with a generously dimensioned brake system which offers a high performance reserve. The front axle wheel brakes have lightweight aluminium calipers and lightweight discs. Increased brake caliper rigidity conveys a direct and sporty braking feel. All brake pads already meet the highest environmental standard, which stipulates the use of copper-free brake pads and does not come into force until 2021. The paint coating on the brake discs contributes to the outstanding appearance of the vehicle. The Audi Q7 is now equipped with the electronic parking brake (EPB). The foot controls and the brake servo are new developments designed with a strong emphasis on weight saving. The Audi Q7 features the new ESC system (ESP 9) by Robert Bosch AG - a highperformance stability control system.Wheel braking systemsFront axle wheel brake systemEngine typeV6 3.0 TFSI 245 kW V6 3.0 TDI 200 kW 7-seater 18“ AKE fixed caliper brake 6 30/36/38 mm 375 mmV6 3.0 TDI 200 kW 5-seater 17“ AKE fixed caliper brake 6 30/36/38 mm 350 mmMinimum wheel size Brake type Number of pistons Piston diameter Brake disc diameterWheel brake AKE (fixed caliper brake)633_04622 BackRear axle wheel brake systemForwards Ξ ContentsEngine typeV6 3.0 TFSI 245 kW V6 3.0 TDI 200 kW 7-seater 18“ TRW PC44HE 1 44 mm 350 mmV6 3.0 TDI 200 kW 5-seater 17“ TRW PC43HE 1 43 mm 330 mmMinimum wheel size Brake type Number of pistons Piston diameter Brake disc diameter633_047Electromechanical parking brake (EPB) An important new feature of the Audi Q7 is the electromechanical parking brake. In terms of design, function, operation and service operations, the system is identical to that used in current Audi models. The software for activating the actuators is integrated in the ABS control unit J104. For detailed information about the design, function and service operations, please refer to Self Study Programme 612.633_04923 BackForwards Ξ ContentsBrake servo, master brake cylinder, pedal assemblyA size 9/9 tandem brake servo is used on the Audi Q7 in both left and right hand drive markets. This TRW brake servo is a new development. Compared to the 9/10“ brake servo of the previous Q7 model, a great deal of weight has been saved by using aluminium as a housing material. The brake light switch is a carryover from the transverse platform (Audi A3, Q3, TT) and is mounted on the tandem master brake cylinder. The brake circuit layout is new: The front and rear axle wheel brakes on the Audi Q7 have separate brake circuits ("black-and-white" configuration; the configuration in the previous model is diagonal).633_050The pedal assembly is a new development. A strong emphasis was placed on weight saving. The pedestal for mounting the pedals is a die-cast aluminium construction and is bolted to the module cross-member. The brake pedal is made from an aluminium profile, while the accelerator pedal is a plastic construction. The pedals are in a suspended arrangement.633_05124 BackForwards Ξ ContentsESCSystem components The Audi Q7 uses ESP9 - the new generation ESC system by Robert Bosch GmbH. In the hydraulic unit a six-piston pump works in combination with the new hydraulic valves to meet the exacting demands on pressure buildup dynamics. Depending on the trim level, there are two physically different versions of the ESC system. A hydraulic unit with 3 pressure sensors is used for models with ACC. One pressure sensor measures the pilot pressure in the hydraulic system while the other two pressure sensors measure the pressure in both braking circuits. In models without ACC, only the pilot pressure is measured. The ESC receives information on vehicle dynamics (transverse and longitudinal acceleration and the yaw rate) from the airbag control unit J234 via the FlexRay bus. The relevant sensors are integral to this control unit on the Audi Q7.633_052Active speed sensor with a rotation direction sensing feature are used on the Audi Q7. In terms of design and function, they are identical to the sensors used on the current Audi A6 and A7 models. The steering angle sender is a magnetic sensor, which is installed in the steering column switch module and communicates via the FlexRay bus. This sender is an improved version of the sender used in the Audi A6 and A7 models. However, the service operations are identical.Functional principle The ESC on the Q7 also performs the basic and additional functions implemented on the current Audi A6, A7 and A8 models. For detailed information about this system, please refer to Self Study Programme 475. In addition, other driver assist and safety systems have been networked. This enables trailer assist and turn assist (available for the first time in the Audi Q7) to request corrective braking inputs from the ABS control unit J104. The Audi Q7 is equipped as standard with the Hill Hold Control (HHC) assistance function. The hold time is approx. 2s, after which the brake is released again and the driver must brake the vehicle himself if required. The Hill Start Assist function has been improved for the Audi Q7. The switch-activated function holds the vehicle stationary if the driver brings it to a standstill by applying the service brake. The function stays active even after the vehicle in driven away again with a forward gear selected. If, on the other hand, the vehicle is driven away again in reverse after stopping and exceeds a speed of approx. 2 kph, Hill Start Assist is automatically deactivated. This innovation significantly improves comfort during manoeuvring and parking. If the vehicle subsequently exceeds a speed of approx. 10 kph when driving forwards, the function is automatically reactivated.633_053633_05425 BackOperation and driver information Offroad mode can be activated by briefly pressing the ESC button ( 3s). In this mode, the scope of TCS and ESC corrective inputs is limited. The control parameters are selected so that the main focus is on traction. If the ESC button is pressed for longer than 3 s, TCS and ESC are fully deactivated.Forwards Ξ Contents633_055A new function generates a driver warning if the wheel brakes reach a high temperature on descents. The brake temperature can rise rapidly, particularly on descents, if the driver fails to select a gear which does not utilise the full deceleration potential of the driveline.If the brake servo does not provide sufficient boost, ESC generates additional braking force by actively building up brake pressure. This function is known as the "optimised hydraulic brake servo (OBBS)" and is an integral part of the ESC systems used on Audi models (refer to SSP 475). If a fault occurs in the vacuum supply system for the brake servo or in the brake servo itself, the result is an increased need for "ESC assistance". This information is provided to the driver in the form of the yellow ESC warning symbol. If this warning is given continuously, it is essential to have the brake servo inspected by a service centre. In the Audi Q7, for the first time, the warning symbol changes colour from yellow to red if the driver ignores the warning for a lengthy period of time (after a defined number of driver braking inputs).633_056Service operations The ESC service operations defined for the Audi Q7 are essentially identical to those of the current Audi A6, A7 and A8 models. The control unit and hydraulic unit can be separated by service personnel and, therefore, can also be replaced separately. A condition is the use of workshop equipment VAS 6613 in order to protect the electronic components of the control unit against static charge buildup. After venting the brake system, it is necessary to encode the new control unit online and to calibrate steering angle sender G85 (as an integral part of the steering column electronics). 3 further basic settings follow: • Check for interchanging of the connected hydraulic lines (the vehicle must be elevated on the hydraulic hoist for this purpose) • Basic setting of electrical parking brake (EPB) For this purpose, the brake is fully opened and closed again once only (previously: 3 opening and closing cycles). • Basic setting of tyre pressure indicator (TPI) The final control diagnostics conclude the test plan for system function test purposes. The steering angle sender G85 does not lose its calibration after disconnecting terminal 30.ESD table mat with equipotential bondingWristband633_056aWorkshop equipment VAS 661326 BackForwards Ξ ContentsSteering systemOverviewThe Audi Q7 now also has electromechanical steering (EPS). Special steering maps which can be configured with Audi drive select were developed. A mechanically adjustable steering column is standard and an electrically adjustable steering column is optional. The standard trim comprises a newly developed four spoke steering wheel. Two three spoke steering wheels are custom options.Steering wheel Four spoke steering wheel as standard Three spoke steering wheel as optionSteering column mechanically adjustable (electrical adjustment is optional) Height adjustment: ± 20 mm Longitudinal adjustment: ± 34 mm633_057Electromechanical power steering (EPS) Use of Q7 specific maps27 BackForwards Ξ ContentsSystem components and operationElectromechanical power steering (EPS) In terms of design, function and service operations, the electromechanical steering system is identical to the system already used on the current Audi A6, A7 and A8 models. Refer to Self Study Programme 612 for detailed information.633_058They can only be set by selecting the relevant mode in Audi drive select. Depending on whether "auto", "dynamic" or "comfort" mode is selected, the system activates steering maps which provide balanced, dynamic or comfort-oriented steering assistance. When "individual" mode is selected, the driver can freely select one of 3 maps. When "efficiency" and "allroad" mode are selected, the map for "auto" mode is activated. When "offroad/lift" is selected, the map for "comfort" mode (comfort-oriented) is utilised.Vehicle: Audi drive select633_022Steering column In terms of design and function, the mechanical and electrical steering columns are identical to those used on the Audi A6 and A7 models. The following major detail modifications were made: The foot controls are attached to the module cross member, and no longer to the steering column bracket, allowing a more filigree bracket design to be realised. This, in combination with further lightweight design measures including the steering shaft, provides a weight reduction of approx. 2 kg. The steering lock attachment has been modified in order to increase anti-theft security. The control unit for activating the control motors of the electrical steering adjustment system is connected to the control unit by a plug (it is bolted on the A6 and A7). The electrical connections are now on the steering column.633_058aSteering wheel A four spoke steering wheel is standard. Two variants of the three spoke steering wheel are optional. The steering wheels are available in various colours with colour-coordinated stitching. All available steering wheels are leather bound.There are differences in regard to the decorative trims used. As the Audi Q7 is exclusively equipped with tiptronic, all available steering wheels have tiptronic paddles. The four spoke steering wheel and the three spoke steering wheel can, as an option, be ordered without a flat bottom with heater.633_059aFour spoke steering wheelThree spoke steering wheel without flat bottomThree spoke steering wheel with flat bottom28 BackForwards Ξ ContentsAll-wheel steeringOverviewFor the first time in Audi models, all-wheel steering is optional on the Audi Q7. Depending on the actual speed of the vehicle and the driving situation, the tracking is adjusted dynamically with the aim of improving driving dynamics and ride comfort. The control process generally comprises 2 different steering operations: parallel steering and countersteering relative to the steered front wheels.633_027Countersteering One of the key aims for countersteering the front and rear wheels is to improve handling at low speeds and to reduce the travel envelope of the vehicle. The advantage for the driver is that less steering effort is required given the same curve radius and the same speed. The vehicle is subjectively much more manoeuvrable and agile. To make full use of the advantages offered by the system, countersteering is only activated in the low speed range (up to approx. 60 kph).The graphic shows the advantage of all-wheel steering using the smallest turning circle as an example. Radius R2, which is achieved using all-wheel steering, is much smaller than the radius (R1) achievable with traditional steering.633_02829 BackParallel steering (in same direction) 1. Steering manoeuvre with a front-steered vehicle Fig. 1: The driver executes a cornering manoeuvre or a change in direction by turning the front axle wheels inwards using the steering wheel. The front wheels begin to transmit lateral friction force due to the (enforced) deformation of the tyre contact surface when turning the wheels inwards. To generate yaw motion about the vehicle's vertical axis, the rear wheels must be able to absorb sufficient lateral friction force.Forwards Ξ ContentsLateral accelerationYaw torque633_029Fig. 2: The lateral friction force now changes direction due to the mass of the vehicle pushing towards the outside of the corner, with the result that lateral acceleration can now be generated. Initiating the change in direction of travel at the front axle alone produces a relatively high yaw torque (torque about the vehicle's vertical axis) until a steady-state condition has been reached. This can have a detrimental effect on comfort and cause the vehicle to become unstable. If for example the driver performs a sudden steering movement in order to avoid an obstacle, unintentional vibration about the vehicle's vertical axis can adversely affect driving stability.633_0302. Steering manoeuvre with a rear-steered vehicle Fig. 1: The driver executes a cornering manoeuvre or a change in direction by turning the front axle wheels inwards using the steering wheel. The system responds to the steering input by initiating parallel steering of the rear wheels. Because of the (enforced) deformation of the tyre contact surfaces at all 4 wheels, the equidirectional lateral friction forces take effect parallel to the front axle wheels due, also, to the rear wheels. The resulting yaw torque is much lower than in a vehicle with front-steered wheels only. The immediate buildup of lateral (cornering) force at both axles signficantly reduces the transition time from the initial steering input to the steady-state condition - a well-known effect which occurs in purely front-steered vehicles. The change in the direction of travel is initiated much more harmoniously and comfortably and the danger of yaw oscillation is reduced Fig. 2: A steady-state condition has been reached and the vehicle is following the trajectory defined by the driver.633_031Lateral friction forces633_032 30 BackCountersteering of the rear wheels is employed in the low speed range while parallel steering is employed at higher speeds.Forwards Ξ ContentsIn addition to the above-mentioned advantages, the system also limits the yaw rate when the driver takes sudden evasive action. In these situations, overproportional parallel steering of the rear wheels helps to increase driving stability.Evasive action/lane change of a car with conventional steering.633_033aEvasive action/lane change with all-wheel steering.633_03331 BackForwards Ξ ContentsTechnical implementationThe tracking values of the rear wheels are modified by an active control element. As with a conventional rear axle, the track rods are mounted in rubber-metal bearings on the wheel carriers. They are not attached directly to the subframe like a conventional axle, but are attached to both sides of the control element by rubbermetal bearings. The entire unit comprising the control element, drive and electronic controller is attached to the subframe and simultaneously steers both wheels through the same angle. Given that the maximum tracking angle adjustment is only approx. 5 °, it is not necessary to use a pivot bearing on the front axle. The angular adjustments are realised by utilising the elasticity of the link/wheel carrier bearing elements.633_034c32 BackForwards Ξ ContentsSystem componentsSpindle driveIndex sensorSpindle driveBelt drivePowerpack: consisting of electronic control unit and power output stageThree phase AC synchronous electric motor with rotor position sensor633_034aThe electric motor drives the spindle nut via the drive belt. The rotational movement of the spindle nut is converted to linear movement of the spindle. The connected track rods transmit the linear movement to the wheel carriers and the wheels are steered in parallel to the right or left (depending on the direction of rotation of the electric motor). The system is self-locking due to the transmission ratio and the trapezoidal thread of the spindle and the spindle nut.The electric motor is only activated during the adjustment process and otherwise stays inactive. The stopping forces are generated solely through the self locking of the screw drive. The maximum adjustment travel of the spindle (from the centre position) is approx. 9 mm, which is equivalent to a maximum wheel lock of approx. 5 °Track rod attachmentThreaded spindleIndex sensor Magnetic pinSpindle nut Drive belt Belt pulley633_03533 BackIndex sensor The index sensor senses the zero position, i.e. the "centre position", of the spindle drive in the non-steered/neutral state. The sensor works on the basis of the Hall-effect principle. For this purpose, the spindle has a pin to which is attached a permanent magnet. Spindle position sensing is performed in an analog fashion within a small angular range about the zero position. The actual Hall effect sensor is preceded by a 2 additional Hall effect switches on the sensor PCB. These switches are used to detect the direction of movement of the spindle.Forwards Ξ ContentsIndex sensorHall switchHall sensorPermanent magnet633_036SpindleElectric motor A brushless three-phase AC synchronous motor is used as a drive. The three-phase current is produced by an AC/DC converter in the drive unit. A rotor position sensor is integrated in the motor. This sensor determines the position of the rotor with high precision.633_037Electric motorControl unitRear steering control unit J1019 The control unit and the drive unit are bolted to the electric motor as a compact unit sealed against water spray and moisture. The control unit is connected to the FlexRay bus as a low-ohmic end user. It computes the drive currents required for the electric motor on the basis of defined input information. An AC/DC converter supplies the alternating voltage to drive the motor.Powerpack34 BackForwards Ξ ContentsFunction of the overall systemThe rear axle steering system generally requires the following measurement data/information: • Wheel speeds Information on wheel speeds is placed on the FlexRay bus in the form of a message from the ABS control unit J104. From this, the rear axle steering control unit J1019 determines the vehicle reference speed, which, to provide redundancy, is compared with the vehicle reference speed determined by ESC. • Steering angle The steering angle is measured by steering angle sender G85 and also transmitted in the form of a message via the FlexRay bus. The control unit determines the required rear steering angle from the "master information", i.e. speed of vehicle and steering angle of front axle wheels. Behaviour at terminal 15 on When the ignition is turned on (terminal 15 message via FlexRay), the control unit checks to see if the following requirements for operation of the rear steering have been met: • The steering assistance provided by the electromechanical steering at the front axle is greater than 20 % of maximum steering assistance. • The vehicle battery (terminal 30) is connected and intact. • The control unit and steering unit have not been interchanged (comparison of stored vehicle identification number (VIN) with the VIN of the current vehicle received via the FlexRay bus). • The rear steering has been correctly programmed/encoded.ABS control unit J104Wheel speedSteering angle sender G85Steering angle Electric motorRear axle steering control unit J1019 Index sensor Index signalActivation currentRotor position sensor Rotor position633_036FlexRay633_039Response to steering inputs by the driver When the control unit is encoded, maps defining the steering angle of the rear axle as a function of vehicle speed and front axle steering angle are stored in the control unit. The maps differ with regard to the desired steering/driving behaviour (driver input). Depending on the drive select setting selected by the driver, there are various maps which support driving styles ranging from comfort-oriented to sporty. If steering inputs are made by the driver at low speeds (up to approx. 60 kph 1)), the rear wheels are countersteered relative to the front wheels up to a max. angle of approx. 5 ° 1).The steering angle of the rear wheels increases with the steering angle of the front wheels (steering angle applied by the driver), with additional allowance being made for the speed of the vehicle. At higher speeds (upwards of approx. 70 kph 1)), parallel steering movements of the rear wheels are realised with much smaller steering angles.1) The specified values differ depending on vehicle type and trim level (depending on application) and serve only to convey a basic understanding of the functional principle.35 BackForwards Ξ ContentsBasic functionBehaviour when vehicle is stationary When the vehicle is stationary, the rear wheels are always set to the neutral position (starting position). The exact position is determined by evaluating the measurement data supplied by the index sensor and the rotor position sensor. In isolated cases, a complete reset may not be possible due to insufficient resetting force. The behaviour described above is mainly due to the load state (higher vehicle weight) and the road surface characteristics (high friction coefficient). In these cases, the rear wheels are reset to the neutral position during the next driving cycle. This "misalignment" is indicated to the driver (refer to owner's manual and driver information).Additional functions/special operating statesInputs from other vehicle systems The Audi parking system (APS) and trailer manoeuvring assist (TMA) may "request" certain rear axle steering angles. The control units in question can specify exact steering angles, which are then implemented by the rear axle steering control unit J1019. ESC can also influence the rear axle steering. If beneficial to driving stability, ESC can suppress certain steering movements of the rear wheels.36 BackForwards Ξ ContentsOperation and driver informationThe driver can directly influence the function of the rear axle steering by selecting the vehicle behaviour in Audi drive select. Depending on the setting selected, the system supports a sporty, balanced or comfortable steering response. When "individual" mode is selected, the driver can freely select one of 3 maps. When "efficiency" and "allroad" mode are selected, the map for "auto" mode is activated. When "offroad/lift" is selected, the map for "comfort" mode (comfort-oriented) is utilised. The driving mode to vehicle behaviour/map assignments are, therefore, identical to those of the electromechanical front axle steering (EPS).The driver receives information on the rear axle steering only in the event of system malfunctions. Depending on the weighting of the fault, a yellow or red warning symbol is displayed. This warning symbol is identical to the familiar symbol used already by the electromechanical front axle steering. The following additions are new: "Adapt driving style. Turning circle larger" and "Please stop vehicle. Note distance to side." These texts are only activated in conjunction with faults at the rear axle.Steering: Fault! Adapt driving style Turning circle largerSteering: Fault! Please stop vehicle Note distance to side633_042633_04337 BackForwards Ξ ContentsService operationsThe rear axle steering system has the production control number (PR number) 0N5. The diagnostic address is CB. The system leaves the factory in the starting position (zero position). The starting position is determined/calibrated by the system supplier. It is not necessary to carry out service work on the system for this purpose. The system can only be adapted to the vehicle by setting the tracking values of the rear wheels. This setting is achieved by turning the designated eccentric screws in the same way as on a vehicle without rear axle steering.Installation and removal/replacement of the steering module The rear axle steering is only available as a complete module in service centres. No provision has been made for the removal/ replacement of individual components. Care must be taken to ensure exact positioning of the module during installation. This is achieved using a special tool. Details of the tool and its usage were still pending clarification at the time of going to press. For detailed information, please refer to the current workshop manual. If the module is not positioned exactly, the positions in the z direction of the track rod attachment points may differ on the left and right hand sides of the vehicle. This will result in unwanted differences in tracking angle on the left and right rear wheels when the springs compress and rebound. After the module is replaced, the new control unit is encoded online. In the process, the vehicle-specific dataset is downloaded from the vehicle database. A wheel alignment computer is required for subsequent adjustment the rear axle tracking angles. Before commencing the alignment procedure, the exact centre position of the steering system is set by performing the basic setting procedure "active steering to centre of steering rack" with the diagnostic tester. The centre position of the steering rack is set with high precision as the tolerance range is much smaller than in "normal operation". An entry is made in the event memory and the yellow warning symbol is activated. On completion of tracking adjustment, the basic setting is deactivated, the event memory entry is cleared and the warning symbol is deactivated after a terminal 15 cycle.633_044To interchange modules, it is necessary to carry out the basic setting procedure "reset/program VIN" and to subsequently encode the control unit online.Note Please bear in mind that the complaint "steering wheel is skewed" may also be due to inexact setting of the rear axle steering starting position due to system parameters.38 BackForwards Ξ ContentsAdaptive Cruise Control (ACC)System overviewThe fourth generation ACC is featured for the first time on the Audi Q7. The modified design and extended range of functions provide a significant improvement in comfort. System availability has also been increased. For example, a system shut-down due to insufficient sensor vision now takes effect much later than before. The existing system limitations have been pushed further back by the modified hardware. For example, radar signal reflection (which can lead to misinterpretation when driving through tunnels) has been minimised and is unlikely to cause the system to shut down. New functions include the system response to stationary vehicles. The measurement data generated by the ACC is an important basis for the new predictive efficiency assist and traffic jam assist functions. As previously with the A6, A7 and A8 models (including the S and RS models), a master/slave concept with 2 radar units is also implemented on the Audi Q7. As before, each radar unit has its own control unit which is combined with the radar unit. Data is exchanged via the FlexRay bus.633_060ADR sender, right G259 and ACC control unit J428 (master)Left ADR sender G258 and ACC control unit 2 J850 (slave)Note Like all other assistance systems, ACC also operates within certain system limits. The responsibility for driving the vehicle in traffic lies with the driver.39 BackForwards Ξ ContentsDesign and basic function of system componentsADR sender, right G259 and ACC control unit J428 (master) Left ADR sender G258 and ACC control unit 2 J850 (slave) The physical structure of both radar units is identical and the only differences are of a functional nature in the control unit software. A key modification is the use of six horizontally aligned radar transceiver units and an additional vertical transceiver unit. At close range (up to approx. 150 m), this gives horizontal and vertical radar visibility ranges/coverage of ± 22 ° and ± 3 °, respectively. The range has been extended to about 250 m. The sensors are positioned on the outer extremes of the vehicle in order to extend the visibility range. This makes it possible, for example, to "look beyond" a column of vehicles ahead. Vehicles in adjacent lanes are detected at an even greater distance within the limitations of the system.Distance [m]Lateral distance [m] Propagation characteristic of the radar beams633_061The ACC master and ACC slave are autonomous control units/ sensors which independently pick up radar reflection within their radar visibility range. Information is exchanged via the FlexRay bus. The slave supplies the master with measurement data. The information generated by both sensors is collated in the master. The functions available to the driver (ACC, traffic jam assist, Aud PreSense etc.) and the driver information displays are implemented by the driver only. The following figures give an idea of the complexity of the detection and control processes. To function properly, ACC system needs to exchange data with 22 other control units. In the process, the ACC master control unit receives and processes around 1000 signals/messages and itself sends around 500. The ACC slave control unit can simultaneously detect up to 32 objects.633_062ACC control unit J428Terminal 15Ground pinACC control unit 2 J850FlexRay633_06340 BackACC basic function The same physical functional principle also applies, of course, to the fourth generation ACC. Targets ahead of the sensor reflect the radar signal, and the reflected signal components are evaluated with regard to amplitude and frequency. Relative speeds and distances are determined by utilising the Doppler effect (or Doppler shift). For detailed information, please refer to Self Study Programme 620 "Audi ACC systems". The ACC is, as per usual, operated using the control stalk. A new feature is that 5 distances can now be set relative to a vehicle ahead (previously 4). Another new feature is the LIM button on the ACC control stalk. This is used for switching between ACC mode and speed limiter. If the vehicle has Audi Drive Select, the ACC program is coupled to the setting selected here. Alternatively, ACC can be configured independently using the "Individual" setting. If the vehicle is not equipped with Audi drive select, the ACC drive program is selected via a separate menu. The driver displays relevant to ACC are largely identical to those on current Audi models equipped with ACC. For further information, please refer to the current owner's manual.Forwards Ξ Contents633_064633_068Vehicle: Audi drive selectACC auxiliary functions The following additional ACC functions are implemented on the Audi A7. • ACC Stop & Go • Distance indicator/distance warning • Evasion assist • Turning assist • Traffic jam assist • Control response when cornering 1) • Boost function 1) • Overtaking assistance 1) • Start-off monitoring 1) • Lane change assistance 1) • Right lane overtaking prevention 1) ACC also supplies important information which is required to implement the predictive efficiency assist systems/functions and for Audi pre sense front.1)633_022 The functional principle is identical to that of same-named functions on other current Audi models. For detailed information, please refer to Self Study Programme 620 "Audi ACC systems".633_064aACC Stop & Go For the first time, ACC also brakes the Audi Q7 in response to vehicles stationary at the time of object detection. The fol