TECHNICAL DOCUMENTATION
SSP 640 Audi 1,4l 3 cylinder TDI engine

This PDF is currently unavailable.
Read document text
Self Study Programme 640 For internal use onlyAudi 1.4l 3-cylinder TDI engine Series EA288Audi Service Training BackForwards Ξ ContentsThe new modular generation of TDI® engines provides a standardised basis for the diesel engines of the EA288 series. Following the rollout of the MDB (Modular Diesel Platform) with 4-cylinder version, the EA288 series will now be extended to include the new 3-cylinder engine.This 1.4 litre engine rounds out the wide range of Audi diesel engines at the lower end. A focal point of development work was the reduction of CO2‑ emissions with the result that the 1.4l 3-cylinder TDI engine meets the EU6 exhaust emission standard.640_002Learning objectives of this self study programme: This self study programme describes the design and function of the 1.4l 3-cylinder TDI engine. Once you have completed this self study programme you will be able to answer the following questions: • • • • What are the cylinder liners made of? Which components are integrated in the balancer shaft module? Which fuel injectors are fitted? What is the return pressure at the fuel injector?2ContentsIntroductionFeatures _______________________________________________________________________________________________________________________________________________________ 4 Modular design _______________________________________________________________________________________________________________________________________________ 5Engine mechanicalsEngine block __________________________________________________________________________________________________________________________________________________ Crankshaft ____________________________________________________________________________________________________________________________________________________ Pistons and conrods _ ________________________________________________________________________________________________________________________________________ Balancer shaft module _ ______________________________________________________________________________________________________________________________________ 7 8 8 9Oil supplyOil circuit _____________________________________________________________________________________________________________________________________________________ 12 Oil pump _____________________________________________________________________________________________________________________________________________________ 13Cylinder headOverview _____________________________________________________________________________________________________________________________________________________ 14 Valvegear _ ___________________________________________________________________________________________________________________________________________________ 16 Coolant ducts ________________________________________________________________________________________________________________________________________________ 16 Camshaft module ___________________________________________________________________________________________________________________________________________ 17Air supply and turbochargingAir flow _______________________________________________________________________________________________________________________________________________________ 18 Turbocharging _______________________________________________________________________________________________________________________________________________ 19 Intake manifold with swirl flaps _ __________________________________________________________________________________________________________________________ 20 Exhaust gas recirculation _ __________________________________________________________________________________________________________________________________ 21Cooling systemThermal management ______________________________________________________________________________________________________________________________________ 25 Active coolant pump ________________________________________________________________________________________________________________________________________ 25 System overview ____________________________________________________________________________________________________________________________________________ 26Fuel systemSystem overview ____________________________________________________________________________________________________________________________________________ 31 Fuel delivery unit ____________________________________________________________________________________________________________________________________________ 32 Fuel pump _ __________________________________________________________________________________________________________________________________________________ 33 Fuel injectors ________________________________________________________________________________________________________________________________________________ 34Engine management systemSystem overview (2015 model Audi A1) __________________________________________________________________________________________________________________ 36 Exhaust system _ _____________________________________________________________________________________________________________________________________________ 38AppendixSelf study programmes _ ____________________________________________________________________________________________________________________________________ 39The self study programme teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a repair manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. This content is not updated. For further information about maintenance and repair work, always refer to the current technical literature.NoteReference3 BackForwards Ξ ContentsIntroductionFeatures• • • • • • • • • 3-cylinder inline engine 4 valves per cylinder, double overhead camshafts (DOHC) 1 intake camshaft and 1 exhaust camshaft Die-cast aluminium engine block Exhaust turbocharging with indirect charge air cooling and exhaust turbocharger with variable turbine geometry (VTG) Timing belt drive gear Intake manifold with swirl flaps Balancer shaft module with oil and vacuum pump Dual-circuit exhaust gas recirculation system comprising high and low pressure exhaust gas recirculation circuitsLow pressure exhaust recirculation circuit1)Exhaust treatment module1)Cylinder head2)Engine block2)Active coolant pump1)Timing belt and auxiliary drive1)Oil pan1)Balancer shaft module2) with oil and vacuum pumpReference The design and function of the basic engine are explained in Self Study Programme 608 "Audi 1.6l / 2.0l 4-cylinder TDI engines".4 BackForwards Ξ ContentsModular designExhaust turbocharger1)The Modular Diesel Platform concept of the EA288 series is based on the subdivision of the engine's functional units into modules. Depending on the requirements relating to engine displacement, engine power, exhaust emissions standard and vehicle class, the engines can be configured from the same and, where required, modified unit modules of the basic engine and attachments. The use of modular design means it is possible to meet the current requirements relating to fuel pressure, exhaust emissions and power delivery while also addressing future challenges such as the cost-effective introduction of national and regional legal requirements.High pressure exhaust recirculation circuit1)Crankcase breather module1)Camshaft module1)Oil filter module1)Intake and charge air system with liquid-cooled charge air cooler2)High pressure injection system1)640_0481) 2)Module offering synergy with existing diesel platform Newly developed modules5 BackForwards Ξ ContentsSpecifications Torque-power curve Power output in kW Torque in Nm640_051Engine speed [rpm]640_004The engine code is positioned at the front left below the cylinder head on the protruding edge of the engine block, as seen in the direction of travel.Features Engine code Type Displacement in cm3 Stroke in mm Bore in mm Number of valves per cylinder Firing order Compression ratio Power output in kW at rpm Torque in Nm at rpm Fuel type Turbocharging Exhaust gas treatment Emission standard CO2 emissions in g/kmSpecifications CUSB 3-cylinder inline engine 1422 95.5 79.5 4 1–2–3 16.1 : 1 66 at 2750 – 3500 230 at 1500 - 2500 Diesel to EN 590 Exhaust turbocharger with variable turbine geometry • Oxidising catalytic converter and diesel particulate filter • Exhaust gas recirculation with high and low pressure sections EU 6 89 (combined)6 BackForwards Ξ ContentsEngine mechanicalsEngine blockTo reduce weight, the engine block is manufactured from die-cast aluminium (AlSi9Cu3). Even the switching from cast iron to aluminium alone was enough to bring a reduction in weight. Thermally joined thin wall liners made from cast iron (GJL 250) serve as cylinder liners. The engine block is heated so that it can expand. At the same time, the cylinder liners are supercooled in order to shrink them. As a result, the new engine is 11 kg lighter than an equivalent cast iron 3-cylinder engine and no less than 27 kg lighter than the 1.6l 4-cylinder TDI engine. The principle of deep-seated cylinder head bolts was adopted from the EA288 diesel engine series. This improves power flow distribution within the structure of the engine block and pressure distribution within the cylinder head gasket.Deep-seated cylinder head boltsCast iron cylinder liners (thermally joined)Die-cast aluminium engine blockDie-cast aluminium oil pan top sectionOil level and temperature sensor G266Sheet steel oil pan bottom section640_011 7 BackForwards Ξ ContentsCrankshaftThe steel crankshaft is mounted in 4 bearings and has 2 counterweights for balancing the rotating inertial forces. In addition, the drive pinion for driving the balancer shaft module is shrunk on the crankshaft on the timing belt side.Pistons and conrodsThe pistons are made of aluminium. They have an annular oilway in the top land ring zone, where they are subjected to high thermal stresses. Fresh, cooled engine oil is sprayed directly into the piston through an inlet port while the piston is in the BDC position. At the same time, the fresh oil displaces the heated oil out of the annular oilway and back into the oil pan. To reduce friction, the pistons are graphite-coated on the breakdown torque side. The pistons are connected to the crankshaft by cracked trapezoidal conrods.Graphite coating on pistonAnnular oilwayOutlet port in piston from annular oilwayInlet port in piston to annular oilwayPiston cooling jetsCrankshaft counterweightsTrapezoidal conrodBalancer shaft module input gearCrankshaft counterweightsDrive gear for timing belt of engine control unit640_012 8 BackForwards Ξ ContentsBalancer shaft moduleTo balance out the free inertial forces, use is made of a balancer shaft which rotates counter to the crankshaft at engine speed. The balancer shaft module is bolted directly to the engine block in the oil bath of the oil pan. The balancer shaft is driven by the crankshaft through the input gear.DriveMark for positioning relative to crankshaft640_050Crankshaft input gearDrive gear of the balancer shaft moduleBalancer shaft module640_053Note The drive pinion of the balancer shaft module has a polymer coating which allows it to be adjusted for backlash. The coating wears off in the course of use. Without this coating, it is not possible to adjust for backlash. The balancer shaft module must, therefore, be replaced after it has been removed.9 BackForwards Ξ ContentsDesignOwing to space constraints and to keep friction to a minimum, use is made of a balancer shaft with an integrated oil pump and a vacuum pump. Each of the balancing weights has a plastic cover on the opposite side, which prevents frothing of the engine oil.Plastic coverBalancer shaft moduleDouble flutter valveBalancer weightShaftVacuum pumpOil pump coverControl piston10 BackForwards Ξ ContentsFlutter valveOil pump coverInput gearAdjustment ring with control springPlastic coverBalancer weight640_015Intake manifoldRotor with vane cellsVacuum pump The vacuum pump induces air from the brake servo through a vacuum line and ports in the engine block. The extracted air flows through flutter valves into the engine block and ventilates its inner chamber. This air is then admitted into the combustion chamber via the engine breather as a blow-by gas. The double flutter valve provides a cross section which is large enough to expel the oil in the vacuum pump chamber. This helps keep drive torque to a minimum even at low temperatures.11 BackForwards Ξ ContentsOil supplyOil circuitThe oil pump integrated in the balancer shaft module ensures that the engine, crankshaft, cylinder head and exhaust turbocharger are supplied with the correct quantity of oil and the correct oil pressure. The oil pump is regulated and is operated in 2 defined stages.Turbocharger oil supplyCamshaft oil galleryCrankshaft oil galleryOil coolerPiston cooling jetsOil pressure regulating valve N428 Two-stage oil pumpOil pump control pistonOil filter cartridge640_018 12 BackForwards Ξ ContentsOil pumpThe pump is a vane cell pump with an excentrically mounted adjustment ring. To reduce the power required to drive the oil pump, the oil pump has a flow control mechanism. The delivery characteristic can be adjusted using a rotatably mounted adjustment ring. By applying oil pressure to the adjustment ring via a control surface, the adjustment ring can be swivelled against the force of the control spring. A specially shaped intake manifold ensures the reliable intake of engine oil from the oil pan even when the vehicle is under high transverse acceleration.Oil pressure controlThe oil pump operates in 2 pressure stages, which are activated as a function of engine speed. • Low pressure stage: oil pressure 1.8 – 2.0 bar1.8 – 2.0 bar 3.8 – 4.2 bar High pressure setting Low pressure setting Pressure demand• High pressure stage: oil pressure 3.8 – 4.2 bar3000 rpm640_019Low delivery rateHigh delivery rateControl springAdjustment ringControl springAdjustment ring640_057640_055Control surfaceVane cellsDelivery chamberControl surfaceVane cellsDelivery chamberAt low engine speeds, the oil pressure control valve N428 energised by terminal 15 is brought to ground by the engine control unit and opens the active oilway to the control piston. The oil pressure acts on the control surface. The resultant force is greater than that of the control spring and swivels the adjustment ring counterclockwise into the centre of the vane cell pump, with the result that the delivery space between the vane cells decreases. The lower pressure stage is activated as a function of engine load, engine speed, oil temperature and other operating parameters, thereby reducing the drive output of the oil pump.In the upper engine speed range or at high engine load (fullthrottle acceleration), the oil pressure control valve N428 is disconnected from ground by the engine control unit J623 in order to vent the active oilway. The adjustment ring now swivels out of its centre position and enlarges the delivery space between the individual vanes. Oil delivery is increased by enlarging the spaces between the vane cells. The higher oil flow encounters a resistance due to the oil ports and the crankshaft bearing play, causing the oil pressure to increase. This way, it was possible to implement a volume-controlled oil pump with 2 pressure stages.13 BackForwards Ξ ContentsCylinder headOverviewThe cylinder head of the 3-cylinder TDI engine is manufactured from aluminium and is, in principle, based on the cylinder head of the EA288 engine series.Outlet portExhaust valveIntake valveGlow plug 2 Q11 with internal cylinder pressure sender for cylinder 2 G621Coolant temperature sensor G62Intake port640_014Key to illustration on page 15:1 2 3 4 5 6 7 8 9 10 14Fuel pressure sensor G247 High pressure fuel reservoir Fuel pressure regulating valve N276 Clamping elements Crankcase breather hose Fuel injectors Crankcase breather module Cylinder head cover Fine oil separator of crankcase breather (swirls) Hall-effect sensor G4011 12 13 14 15 16 17 18 19 Camshaft module Roller cam follower (intake side) Intake valves Exhaust valves Charge pressure sender G31 Glow plugs Q10, Q11, Q12 Intake manifold with swirl flaps Intake manifold position sender G513 Cylinder head BackForwards Ξ ContentsComponents2 3 415 678119101213141516171819640_044 15 BackForwards Ξ ContentsValvegearThe valvegear components were adopted unchanged from the previous model. Unlike the 4-cylinder engines of the EA288 series, however, the 1.4l 3-cylinder TDI engine does not have an offset radial valve configuration. It has a symmetrical radial valve configuration, where the intake valves are located on the intake side and the exhaust valves on the exhaust side. Good volumetric efficiency is achieved through the parallel arrangement of the valves and by optimising the intake port for pressure loss. An optimised swirl effect is achieved inside the combustion chamber by using a variable intake manifold and a seat swirl chamfer on the intake port.Intake sideExhaust side640_046Coolant ductsTo increase heat dissipation in the combustion chamber area, the water jacket is subdivided into a lower jacket core and an upper water jacket core. The lower part of the coolant port is connected to the upper part by a throttle bore. The advantage of this is that the coolant flows through the combustion chamber plates (valve area) faster than in the upper part. This helps reduce heat influx into the cylinder head. The cylinder head has a cross-flow cooling system, i.e. the coolant flows upwards into the cylinder head on the exhaust side and then transversely though the cylinder head towards the exhaust side.Intake sideUpper coolant jacketExhaust sideLower coolant jacket640_01316 BackForwards Ξ ContentsCamshaft moduleThe cylinder head consists of 2 components: the bearing frame with integral camshafts (integrated valvegear module) and the cylinder head together with its fittings. The camshaft tubes are mounted in a fixture and the finished and heated cam elements and the encoder wheel are held in the correct position in the bearing frame by a joining cassette. Having been fitted with end pieces and supercooled, the camshaft tubes are then guided through the frame mounting points. After the temperatures of the components have been equalised, both camshafts are mounted inseparably in the integrated valvegear module. This method allows the camshaft bearing to be designed for very high rigidity and low weight. To minimise friction, there is a needle bearing on the drive side of the camshaft.Rocker coverHall-effect sensor G40Crankcase breather moduleGasketSender wheel for Hall-effect sender G40 Exhaust camshaftIntake camshaftCamshaft moduleNeedle bearing640_01717 BackForwards Ξ ContentsAir supply and turbochargingAir flowThe intake air flows from the air filter on the turbocharger side of the compressor, the charge air cooler and the throttle flap control unit into the combustion chamber via the intake manifold with swirl flaps, the intake ports and the intake valves.Intake valvesExhaust turbochargerIntake airIntake manifold with swirl flapsCharge pressure sender G31 Intake air temperature sensor G42Charge air temperature sensor after charge air cooler G811 (on reverse)Charge air cooler (liquid cooled) Throttle valve control unit J338Charge air coolingLike the 1.6l / 2.0l TDI engine (EA288), the 3-cylinder engine has a liquid-cooled charge air cooler. For engineering reasons, it was necessary to install the charge air cooler on the gearbox box side on the cylinder head. The charge air cooler consists of 7 horizontal aluminum flat tubes. To achieve optimal heat dissipation into the coolant, turbulence plates and embossings were integrated into the flat tubes. Two senders (intake air temperature sensor G42 and charge air temperature sensor after charge air cooler G811) are used to compare the nominal and actual charge air temperatures. If the actual temperature after the charge air cooler is higher than the nominal temperature, the charge air cooling pump V188 is activated on demand by the engine control unit.Coolant return Coolant supply640_02218 BackForwards Ξ ContentsTurbochargingThe exhaust manifold module consists of the exhaust manifold, the exhaust turbocharger integrated in the exhaust manifold and the low pressure exhaust gas recirculation intake. Use is made of an exhaust turbocharger with a pneumatically actuated variable turbine geometry (VTG) including a position sensor. The engine control unit receives feedback on the position of the vanes from the charge pressure actuator position sensor G581 in the charge pressure actuator. The recirculated exhaust gases are not extracted at the turbine housing, but rather at the diesel particulate filter outlet. This allows the turbocharger to operate in higher efficiency ranges. This allows higher charge pressures and higher volumetric efficiency to be achieved at partial throttle in particular. A benefit of this is the higher cooling capacity of the exhaust gas recirculation system, which helps reduce the mixing temperature of the fresh air and the recirculated exhaust gases. The bearing is lubricated and cooled by the engine oil.Exhaust turbineCharge pressure actuator with vacuum cell and charge pressure actuator position sensor G581 Linkage for vane adjustmentCharge air compressorOil supplyOil returnExhaust manifold640_02319 BackForwards Ξ ContentsIntake manifold with swirl flapsThe swirl effect inside the combustion chamber was optimised with the aid of a variable intake manifold, an adapted intake geometry and a seat swirl chamfer at the bottom end of the intake valve seats.Swirl flap Shaft Charge pressure sender G31 Intake manifold housingGasketPushrodPositioning element with vacuum cellVariable intake manifold position sender G513640_024Intake portsTangential port (swirl port)Tangential port (swirl port)Seat swirl chamferSeat swirl chamferParallel exhaust portParallel exhaust port640_056 20 BackForwards Ξ ContentsExhaust gas recirculationDual-circuit exhaust gas recirculationThe 1.4l 3-cylinder TDI engine has a dual-circuit exhaust gas recirculation system comprising high and low pressure exhaust gas recirculation circuits.High pressure exhaust recirculationThe exhaust gas is extracted from an external duct directly at the exhaust manifold and flows uncooled into the charge air tube via the exhaust gas recirculation servomotor V338. The hot exhaust gases heat the charge air and, together with the charge air, flow into the cylinders via the intake manifold. The inflowing hot exhaust gases heat up the exhaust treatment module quickly and so make it ready for operation in less time. The high pressure exhaust gas recirculation circuit is mainly active during the warm-up phase of the engine. The recirculation rate of the high pressure exhaust gas recirculation circuit is controlled by the engine management system via the exhaust gas recirculation servomotor V338.Charge air tubeIntake manifoldExhaust manifoldExhaust gas treatment modulePoint of entry of exhaust gases into charge airExhaust gas recirculation valve with exhaust gas recirculation servomotor V338External exhaust gas recirculation duct640_031 21 BackForwards Ξ ContentsLow pressure exhaust recirculationAfter passing through the diesel particulate filter, where the soot particulates are removed by a filter insert, the recirculated exhaust gases flow through the liquid-cooled EGR cooler to the exhaust gas recirculation valve. From here, the cooled exhaust gases are directed to the exhaust turbocharger compressor, optimally mixed with the charge air and channeled into the intake manifold system with integrated charge air cooler, where the compressed charge air flows into the intake manifold. To utilise the low pressure exhaust gas recirculation system across the full mapped range, the complete exhaust gas flow from the diesel particulate filter is shut off in a controlled manner by a motor-operated exhaust flap. The exhaust gas recirculation rate is dependent on the pressure gradient between the exhaust and intake sides. As the pressure gradient changes as a function of engine load, it must be regulated. This is done by the exhaust gas recirculation valve V339 on the intake side, working in conjunction with the exhaust flap control unit J883 on the exhaust side. The pressure can rise or fall during this process. • The pressure gradient increases when the throttle flap of the exhaust gas recirculation flap is further opened and the throttle valve of the exhaust flap control unit is further closed. • The pressure gradient decreases when the throttle flap of the exhaust gas recirculation flap is further closed and the throttle valve of the exhaust flap control unit is further opened.Intake manifoldExhaust turbochargerOxidising and nitrogen oxide accumulator catalystDiesel particulate filterCharge air coolerEGR coolerExhaust gas recirculation valve with EGR servomotor 2 V339Exhaust flow for exhaust flap control unit J883640_03222 BackForwards Ξ ContentsExhaust gas treatment moduleTo reduce nitrogen oxide emissions and thus meet the EU6 emission limits, the 1.4l 3-cylinder TDI engine is equipped with a nitrogen oxide accumulator catalyst (NOx accumulator catalyst). To store the nitrogen oxides in the exhaust gases, the oxidising catalyst is coated with barium oxide in addition to platinum, palladium and rhodium and, thus, also acts as an NOx accumulator catalyst. A computational model stored in the engine control unit controls the storage of nitrogen oxides and regeneration of the NOx accumulator catalyst. The computational model utilises the information supplied by the exhaust gas temperature sensors and the oxygen sensors. The diesel particulate filter also serves as a blocking catalyst for the hydrogen sulphide produced during operation of the NOx accumulator catalyst. For this purpose, the diesel particulate filter is coated with a metal oxide.Oxygen sensor G39Differential pressure sender 2 G524Differential pressure sender G505Exhaust gas temperature sender 3 G495Oxygen sensor after catalytic converter G130Oxidising and nitrogen oxide accumulator catalyst Diesel particulate filter Mounting bracket640_035Note The exhaust gas treatment module is bolted to the engine block and to the cylinder head. To allow the exhaust gas treatment module to be installed without tension, the brackets have oblong holes.23 BackForwards Ξ ContentsRemoval of nitrogen oxides (regeneration)If the storage capacity of the NOx accumulator catalyst is exhausted, the engine management system initiates a regeneration cycle. A requirement for regeneration of the NOx accumulator catalyst is that the engine is run on a rich mixture (λ 1) whereby the nitrogen oxides are removed from the carbon monoxide molecules which are plentiful in the rich exhaust gases. The barium nitrate is initially reduced to barium oxide by the carbon monoxide, liberating carbon dioxide and nitrogen monoxide. The NOx accumulator catalyst is coated with rhodium and platinum reduce the nitrogen oxides to nitrogen. The carbon monoxide oxidises to carbon dioxide.Sulphur removalThe removal of sulpur from the NOx accumulator catalyst requires exhaust temperatures of higher than 620 °C. In most cases, regeneration of the diesel particulate filter takes place after sulphur removal. The high exhaust gas temperature which builds up during regeneration of the particulate filter is utilised to reduce the heating-up time of the NOx accumulator catalyst. As soon as the exhaust gas temperature required for sulphur removal is reached, the engine is alternately run lean and rich. During surplus fuel operation, the sulphur (SO) becomes sulphur dioxide (SO2) and hydrogen sulphide (H2S) is removed. During the lean operation phases, the exhaust gas temperature in the NOx accumulator catalyst is set in such a way as to avoid stressing components due to excessively high exhaust gas temperatures. The small quantities of hydrogen sulphide which form during sulphur removal are converted to sulphur dioxide (SO2) by the barrier coating in the diesel particulate filter.Oxidising and nitrogen oxide accumulator catalystDiesel particulate filter640_058 24 BackForwards Ξ ContentsCooling systemThermal managementThe 1.4l 3-cylinder TDI engine has a thermal management system which is designed to shorten the warm-up phase after a cold start and channel the heat produced by the engine to where it can be advantageously utilised to boost vehicle efficiency. The focus here is on reducing intra-engine friction. Other goals are to ensure the early availability of emission reduction measures and to reduce the use of heating measures which have the effect of increasing fuel consumption.Cylinder head coolant valve N489Coolant pump640_049Active coolant pumpAn active coolant pump is used in the thermal management system for the 1.4l 3-cylinder TDI engine. This coolant pump can be switched on and off, allowing coolant circulation to stop when the engine is cold. Static coolant heats up more quickly and can bring the engine up to operating temperature more effectively. A hydraulically actuated control valve (pot) activated by the cylinder head coolant valve N489 slides over the rotating impeller and prevents the coolant from circulating.Cylinder head coolant valve N489Input shaftAnnular piston Impeller with integrated wobble plate Axial piston pump Guide bush with coolant ducts Control valve (pot) Bearing Pump casingAnnular piston ring sealsCompression spring for resetting the control valve Control valve seal640_052Reference For more information about the active coolant pump, please refer to Self Study Programme 608 "Audi 1.6l / 2.0l 4-cylinder TDI engines".25 BackForwards Ξ ContentsSystem overviewThe overall cooling circuit comprises three sub-circuits: • Small cooling circuit (micro circuit) • Large cooling circuit (high temperature circuit) • Cooling circuit with charge air cooling (low temperature circuit)3 21 V4884V3385 9 6 N489 G62 7 8V1881110640_005Key: 1 2 3 4 5 6 7 8 9 10 11 Coolant expansion tank Heater heat exchanger Low pressure EGR cooler Cylinder head Engine block Active coolant pump Engine oil cooler Coolant thermostat Charge air cooler Cooler for low temperature cooling circuit Radiator G62 Coolant temperature sensor N489 Cylinder head coolant valve V188 Charge air cooling pump V338 Exhaust gas recirculation servomotor V488 Heating assistance pumpCooled coolant Hot coolant Charge air cooling26 BackForwards Ξ ContentsSecondary cooling circuit (micro circuit, heating circuit)If the engine is cold, the thermal management system is started in conjunction with the small cooling circuit, thereby ensuring that the engine and interior are heated quickly. The active coolant pump is activated via the cylinder head coolant valve N489. This stops the coolant from circulating within the engine block. The electrical heating assistance pump V488 initiates the secondary cooling circuit in a controlled manner, depending on the coolant temperature in the cylinder head. The A/C control unit registers the driver's temperature preference and takes this into account when activating the coolant pump.3 21 V4884V3385 9 6 N489 G62 7 8V1881110640_006Key: 1 2 3 4 5 6 7 8 9 10 11 Coolant expansion tank Heater heat exchanger Low pressure EGR cooler Cylinder head Engine block Active coolant pump Engine oil cooler Coolant thermostat Charge air cooler Cooler for low temperature cooling circuit Radiator G62 Coolant temperature sensor N489 Cylinder head coolant valve V188 Charge air cooling pump V338 Exhaust gas recirculation servomotor V488 Heating assistance pumpCooled coolant Hot coolant Charge air cooling27 BackForwards Ξ ContentsLarge cooling circuit (high temperature circuit) – coolant at operating temperatureIf the coolant has reached its operating temperature, the coolant thermostat opens and switches to controlled operation. The radiator (main radiator) is integrated in the cooling circuit. The coolant thermostat regulates the engine outlet temperature and is located at the main radiator inlet.3 21 V4884V3385 9 6 N489 G62 7 8V1881110640_007Key: 1 2 3 4 5 6 7 8 9 10 11 Coolant expansion tank Heater heat exchanger Low pressure EGR cooler Cylinder head Engine block Active coolant pump Engine oil cooler Coolant thermostat Charge air cooler Cooler for low temperature cooling circuit Radiator G62 Coolant temperature sensor N489 Cylinder head coolant valve V188 Charge air cooling pump V338 Exhaust gas recirculation servomotor V488 Heating assistance pumpCooled coolant Hot coolant Charge air cooling28 BackForwards Ξ ContentsCooling circuit with charge air cooling (low temperature circuit)The intake manifold temperature is used as a reference variable for activating the charge air cooling circuit (low temperature cooling circuit). After this target temperature is reached, the intake manifold temperature is regulated by activating the charge air cooling pump V188.3 21 V4884V3385 9 6 N489 G62 7 8V1881110640_008Key: 1 2 3 4 5 6 7 8 9 10 11 Coolant expansion tank Heater heat exchanger Low pressure EGR cooler Cylinder head Engine block Active coolant pump Engine oil cooler Coolant thermostat Charge air cooler Cooler for low temperature cooling circuit Radiator G62 Coolant temperature sensor N489 Cylinder head coolant valve V188 Charge air cooling pump V338 Exhaust gas recirculation servomotor V488 Heating assistance pumpCooled coolant Hot coolant Charge air cooling29 BackForwards Ξ ContentsFuel systemThe 1.4l 3-cylinder TDI engine is equipped with a common rail fuel injection system by Delphi. The fuel injection system uses a singlepiston high pressure pump to produce an injection pressure of up to 2000 bar and thus supplies the injectors with the required fuel pressure. As before, the fuel injection system is controlled by the engine control unit based on the following influencing variables: • Engine load • Engine speed • TemperatureInjectors N30 – N32Fuel pressure sensor G247High pressure fuel reservoir (rail)Fuel pressure control valve N276Fuel pumpFuel metering valve N290640_02530 BackForwards Ξ ContentsSystem overviewFuel metering valve N290Fuel pressure sensor G247High pressure fuel reservoir (rail)Fuel pressure regulating valve N276High pressure pump CP4.1Injectors N30, N31, N32 Fuel temperature sender G81 Pressure limiting valveEngine control unit J623Battery (positive)Fuel filterGround Fuel pump control unit J538Fuel predelivery pump G6640_009Fuel feed pressure and return pressure from the injectors approx. 5 – 6 bar High fuel pressure approx. 230 – 2000 bar Fuel return from the high pressure pump approx. 0 – 1 bar31 BackForwards Ξ ContentsFuel delivery unitThe fuel delivery unit is directly built into the fuel tank. The fuel predelivery pump G6, the pressure limiting valve for fuel feed and the fuel gauge sender G are integrated in the fuel delivery unit. The fuel predelivery pump channels the fuel to the high pressure pump. It is an electrical, non-regulated internal gear pump. The fuel predelivery pressure is set to approx. 5.8 bar by a mechanical pressure limiting valve.Fuel return lineFuel supply lineFuel line from the fuel pump to the pressure limiting valveConnection to pressure limiting valveFuel line from pressure limiting valve to fuel supply lineHousingFuel predelivery pump G6Pressure limiting valveFuel intakeFloat with linkage connecting to fuel gauge sender GFilter640_02632 BackForwards Ξ ContentsFuel pumpThe single-piston high pressure pump by Delphi has the designation DFP 6.1E. It produces a fuel injection pressure of up to 2000 bar and is driven by the timing belt drive.Fuel metering valve N290High pressure connection with exhaust valve Fuel supply lineInput shaft Fuel return line640_059DesignThe fuel predelivery pump G6 delivers the fuel from the fuel tank to the high pressure pump housing. The fuel metering valve N290 installed in the high pressure pump regulates the high pressure fuel flow as a function of engine load and speed. The pump piston is actuated by a drive shaft with dual cams and a roller. The roller provides for low-friction power transmission.High pressure chamberConnection to high pressure fuel reservoir (rail) Pump piston Pump piston spring Fuel metering valve N290Fuel supply line Roller Fuel return linePump casingDrive shaft with dual cams640_060 33 BackForwards Ξ ContentsFuel injectorsThe 7-hole fuel injectors by Delphi have the designation DFI 1.20 and are rated for injection pressures of up to 2000 bar. To achieve quick injector operating times, an uprated magnetic coil was used. The magnetic coil allows the duration of injection, the start of injection and the number of injection cycles to be regulated exactly. The fuel injectors are controlled by the engine control unit. Technical features are: • Optimised switching valve with uprated magnetic coil • Reduced diameter of the injector pintle • Optimisation of the pintle seatConnection to high pressure fuel reservoir (rail)Connection to fuel return lineSolenoid coilSwitching valveInjector spring Inflow restrictorInjector pintle640_02734 BackForwards Ξ ContentsFuel injection phase controlAs regards the injection phases, a distinction is made between injection during normal engine operation and injection during the regeneration phase of the diesel particulate filter and the nitrogen oxide accumulator catalyst.Injection phases during normal operation and in regeneration modeNormal operation TDCRegeneration mode - heating-up phaseRegeneration mode - regeneration phasePreinjectionsMain injectionPost-injections640_029Normal operation During normal operation, the injectors perform up to 3 injections. • 1 – 2 preinjections and 1 main injection.Regeneration mode In regeneration mode, up to 6 injections are performed: • During the heating-up phase, the injection cycle consists of 2 preinjections, 1 main injection and 2 post-injections shortly after the main injection. • In regeneration mode, the injection cycle consists of 2 preinjections, 1 main injection, 2 post-injections shortly after the main injection and 1 late post-injection relative to the main injection.Note These post-injections result in an exothermic reaction1), where heat is released through the oxidising catalytic converter. Therefore, up to 6 partial fuel injections are performed per combustion cycle across a wide mapped range during the regeneration phase of the particulate filter.1)Exothermic reaction: A chemical reaction which takes place on the surface of the oxidising catalytic converter releasing additional heat into the exhaust gas.35 BackForwards Ξ ContentsEngine management systemSystem overview (2015 model Audi A1)SensorsAir mass meter G70 Engine speed sensor G28 Hall-effect sensor G40 Coolant temperature sensor G62 Intake air temperature sensor G42 Fuel temperature sender G81 Oil level/temperature sensor G266 Fuel pressure sensor G247 Exhaust gas recirculation potentiometer G212 Exhaust gas recirculation potentiometer 2 G466 Accelerator pedal position sensor G79 with accelerator pedal position sensor 2 G185 Knock sensor G61 Brake light switch F Brake pedal switch F63 Combustion chamber pressure sensor for cylinder 2 G678 Oxygen sensor G39 Oxygen sensor after catalytic converter G130 Charge air temperature sensor after charge air cooler G811 Wastegate actuator position sensor G581 Throttle valve control unit J338 Throttle actuator position sensors 1+2 for vehicles with electronic accelerator G187, G188 Variable intake manifold position sender G513 Oil pressure switch F1 Exhaust valve control unit J883 Charge pressure sensor G31 Clutch position sensor G476 Exhaust gas temperature sender 1 G235 Exhaust gas temperature sender 3 G495 Differential pressure sender G505 Exhaust gas pressure sensor 1 G450 Auxiliary signals: • Central control unit for comfort/convenience system • Cruise control system • Auxiliary heater control unit • Starter motor relay 1+2 • Entry and start authorisation control unit36Control unit in dash panel insert J285 with: • Glow period warning lamp K29 • Exhaust gas warning light K83 • Diesel particulate filter warning lamp K231Diagnosis interface for databus J533Engine control unit J623 BackForwards Ξ ContentsActuatorsInjectors for cylinders 1 – 3 N30 – 32Automatic glow period control unit J179 Glow plugs 1 – 3 Q10 – Q12Oil pressure regulating valve N428Throttle valve control unit J338 Throttle valve positioner for electronic power control G186Fuel metering valve N290Fuel pressure control valve N276Exhaust gas recirculation servomotor V338 Exhaust gas recirculation servomotor 2 V339Diagnostic portIntake manifold flap change-over valve N239Cylinder head coolant valve N489Charge air cooling pump V188Charge pressure limitation solenoid valve N75Heating assistance pump V488Exhaust valve control unit J883Heating resistor (crankcase breather) N79Heater for oxygen sensor Z19 Heater for oxygen sensor 1 after catalytic converter Z29Fuel pump relay J17 Fuel pump control unit J538 Fuel predelivery pump G6640_010Auxiliary signals: • A/C compressor • Auxiliary coolant heater • Fan setting 1 + 2 • Auxiliary air heater element Z3537 BackForwards Ξ ContentsExhaust systemThe exhaust system for compliance with the EU6 (W) exhaust emission standard is made up of the following component parts: • Exhaust manifold with integrated exhaust turbocharger • Exhaust gas treatment module with oxidising and accumulator catalyst as well as the coated diesel particulate filter • Exhaust valve control unit J883 • Baffle silencerOverview(2015 model Audi A1)Oxidising and nitrogen oxide accumulator catalystDiesel particulate filterFlexible pipeBaffle rear silencerExhaust flap control unit J883Exhaust valve control unit J883 To utilise the low pressure exhaust gas recirculation system across the full mapped range, the complete exhaust gas flow from the diesel particulate filter is shut off in a controlled manner by a motor-operated exhaust flap. The exhaust gas recirculation rate is dependent on the pressure gradient between the exhaust and intake sides.38640_054 BackForwards Ξ ContentsAppendixSelf study programmesYou will find further information on the technology of the 1.4l TDI engine in the following self study programmes.SSP 477 Audi A1 Order number: A10.5S00.70.20SSP 608 The Audi 1.6l and 2.0l 4-cylinder TDI engines Order number: A12.5S00.92.20SSP 626 Basics of Audi engine technology Order number: A14.5S01.11.2039All rights reserved. Technical specifications are subject to change. Copyright AUDI AG I/VK-35 service.training@audi.de AUDI AG D-85045 Ingolstadt Technical status 03/15 Printed in Germany A15.5S01.23.20640Audi Vorsprung durch Technik