TECHNICAL DOCUMENTATION
SSP 646 Audi A4 (Type 8W) Vehicle electrics

This PDF is currently unavailable.
Read document text
Self Study Programme 646 For internal use onlyAudi A4 (Type 8W) Vehicle electrics and electronicsAudi Service Training BackThe Audi A4 (type 8W) is the second representative of the MLBevo (Modular Longitudinal Platform evolution) after the Audi Q7 (type 4M). A fully equipped Audi A4 (type 8W) has around 90 control units on board, many of which exchange data with one another. Such close co-operation would not be possible without an entirely new electronics architecture compared with the Audi A4 (type 8K) – especially when it comes to the driver assistance systems. The new FlexRay bus system in the Audi A4 networks multiple control units and ensures that data is transmitted extremely quickly and securely. The key components are the engine, the automatic gearbox, the central suspension control unit, the Electronic Stability Control (ESC) system, the power steering control unit, the Stop&Go adaptive cruise control system including traffic jam assist, the video camera and the airbag control unit which manages the safety systems. There are further data networks in addition to the FlexRay bus. CAN bus systems (CAN = controller area network) integrate the air conditioning system and several assistance systems such as Audi side assist and the surround cameras.Forward Ξ ContentsThey also facilitate communication between the comfort/convenience control units, the infotainment modules and central display and operating components such as the MMI and Audi virtual cockpit. So-called LIN buses (LIN = local interconnect network) complement the CAN buses by serving less complex subscriber systems such as the interior lighting. The Bang & Olufsen Sound System with 3D sound uses a MOST bus (MOST = media oriented systems transport). As in other Audi models, the Audi A4 now also has aluminium high-current wires with diameters of 16 mm2, 35 mm2 and 50 mm2. However, the Audi A4 is the first Audi to use aluminium wires with diameters of 2.5 mm2, 4 mm2 and 6 mm2. Thanks to these modifications, the electronics in the new Audi mid-range models contribute to a lightweight design. The weight of the vehicle in this area has been reduced by 6 kg compared with the previous model.646_002Learning objectives of this self study programme: Once you have completed this self study programme you will be able to answer the following questions: • • • • Where are the fuse and relay panels located in the Audi A4? In what locations are electrical components fitted on the car? Which bus systems are used in the Audi A4? What are the tasks of the control units in the car? • What are the versions of the exterior lighting, and how are the individual light functions implemented? • What are the changes with regard to headlight range adjustment and calibration of the Audi Matrix LED headlights?2ContentsVoltage supplyCar battery ____________________________________________________________________________________________________________________________________________________ Jump start terminal __________________________________________________________________________________________________________________________________________ Supply structure _ _____________________________________________________________________________________________________________________________________________ Fuses and relays ______________________________________________________________________________________________________________________________________________ Aluminium wires _____________________________________________________________________________________________________________________________________________ 4 5 6 7 8NetworkingInstallation locations of the control units ________________________________________________________________________________________________________________ 10 Topology _____________________________________________________________________________________________________________________________________________________ 12 Bus systems used on the Audi A4 _________________________________________________________________________________________________________________________ 14Control unitsBrief descriptions ___________________________________________________________________________________________________________________________________________ 16Exterior lightingHeadlight variants __________________________________________________________________________________________________________________________________________ 42 Xenon headlight _____________________________________________________________________________________________________________________________________________ 44 LED headlight _______________________________________________________________________________________________________________________________________________ 46 Audi Matrix LED headlight _ ________________________________________________________________________________________________________________________________ 48 Dynamic turn signal function ______________________________________________________________________________________________________________________________ 50 Tail lights ____________________________________________________________________________________________________________________________________________________ 51 High-level brake lights / number plate lights ____________________________________________________________________________________________________________ 54Audi drive selectFunctional characteristics __________________________________________________________________________________________________________________________________ 56 Displays and operation _____________________________________________________________________________________________________________________________________ 56 Audi drive select function __________________________________________________________________________________________________________________________________ 57 Functional features _________________________________________________________________________________________________________________________________________ 57Vehicle electronicsInterior lighting _____________________________________________________________________________________________________________________________________________ 58 Overhead module ___________________________________________________________________________________________________________________________________________ 62 Anti-theft alarm _____________________________________________________________________________________________________________________________________________ 63 Central locking ______________________________________________________________________________________________________________________________________________ 64 Sensor-controlled luggage compartment release _______________________________________________________________________________________________________ 66 Garage door opener (HomeLink) _ _________________________________________________________________________________________________________________________ 68 Head-up display _____________________________________________________________________________________________________________________________________________ 70AppendixSelf study programmes _ ____________________________________________________________________________________________________________________________________ 71The self study programme teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a repair manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. This content is not updated. For further information about maintenance and repair work, always refer to the current technical literature.NoteReference3 BackForward Ξ ContentsVoltage supplyCar batteryThe car battery in the Audi A4 (type 8W) is housed centrally in the spare wheel well. The main fuse panel and the battery isolation igniter N253 are located at the positive terminal of the car battery. In the event of a crash, N253 disconnects the main battery lead. The battery monitoring control unit J367 is located at the negative terminal of the car battery. This control unit, also known as the battery data module (BDM), combines with the earth lead to form a unit.Battery monitor control unit J367Battery AMain fuse panel and battery isolation igniter N253646_081The following car batteries are used in the Audi A4: Standard batteries 95 Ah/450 A 110 Ah/520 A EFB battery 79 Ah/420 A 93 Ah/520 A AGM car batteries 58 Ah/340 A 68 Ah/380 A 75 Ah/420 A 92 Ah/520 A 105 Ah/580 A EFB battery An EFB (Enhanced Flooded Battery) battery is a heavy-duty wet-cell battery. The positive plate inside the car battery is coated with an additional polyester scrim which provides the active mass of the car battery with additional stability on the plate. The deep-cycle resistance of these car batteries is higher than that of conventional batteries. An EFB battery is charged in exactly the same way as a standard car battery. AGM car battery AGM (Absorbent Glass Mat) car batteries have a glass microfibre material inside in which the electrolyte is held. In addition to having higher deep-cycle resistance, the AGM car battery is noted for its leak-proof design. This is of course very important for installation of the battery inside the car. When charging, it is important to follow the charger's operating instructions and, if required, to program the charger for AGM car batteries.4 BackForward Ξ ContentsJump start terminalThe jump start terminal (positive terminal) is located in the engine bay on the right-hand side of the vehicle, adjacent to the air filter box, under the red plastic cover. The earthing stud (negative terminal) is connected directly to the body fore of the right suspension strut tower. These terminals should also be used for charging the car battery in the showroom or for diagnostics in the workshop.Distributor for term. 30 TV2 with fusesJump start terminalTerminal 30 supplyDistributor supply lineInterference suppression capacitor C24Sealing capEarthing studDistributor 2 for term. 30 TV22Starter/alternator cableConnection to radiator fan control unit J293 (4-cylinder engines) Connection to automatic glow period control unit J179 or secondary air pump relay J299 Connection to radiator fan control unit 2 J671Connection to radiator fan control unit J293646_082The actual jump start terminal is on the terminal 30 distributor TV22 to which the interference suppression capacitor C24 is also attached. The red 70-mm2 cable supplies the distributor. The 3 fuses on the distributor for term. 30 TV2 protect the radiator fan, the glow plugs and the secondary air pump.The black 70 mm2 wire leads from distributor 2 for term. 30 TV22 to the starter. A further wire leads from here to the three-phase AC motor. In 4-cylinder models, the power supply of the radiator fan control unit J293 is located adjacent to the wire leading to the starter/3-phase AC motor.5 BackForward Ξ ContentsSupply structureThe following diagram summarises the supply structure of the Audi A4. This is a schematic diagram. For exact details of fuse assignment and the cable routing, please refer to the applicable service literature.TV22TV2SCTV1SBMain fuse panel SFKey: 1 2 3 4 5 6 A B C 6646_083Connection to auxiliary air heater stage 1 Connection to auxiliary air heater stages 2+3 Connection to radiator fan control unit J293 (4-cylinder engines) Connection to automatic glow period control unit J179 or secondary air pump relay J299 Connection to radiator fan control unit 2 J671 Connection to radiator fan control unit J293 Battery Starter motor AlternatorJ367 Battery monitor control unit J500 Power steering control unit N253 Battery isolation igniter SB Fuse panel B, on the footrest SC Fuse panel C, on the dash panel SF Fuse panel F, in luggage compartment on L/H side TV1 Fuse and relay box at base of right A-post TV2 Distributor for term. 30 TV22 Distributor 2 for term. 30 BackForward Ξ ContentsFuses and relaysThe fuses on the main fuse panel as well as distributors TV1 and TV22 are labelled only "S" in the current flow diagram. This also applies to other individual fuses distributed throughout the car. Fuses "SB", "SC" and "SF" can also be accessed by the driver on the relevant fuse panels and therefore are also described in the Owner's Manual.Relay and fuse panel in plenum chamberDistributor for term. 30 TV2 and distributor 2 for term. 30 TV22 with fusesDistributor for term. 30 TV1 with fusesMain battery lead646_084Fuse panel C on the dash panel, driver side. The fuses here are labelled "SC" in the current flow diagram.Fuse panel B on the driver side footrest. The fuses here are labelled "SB" in the current flow diagram.Fuse panel F in the luggage compartment, rear left. The fuses here are labelled "SF" in the current flow diagram.Main fuse panel at positive terminal of car batteryBattery monitor control unit at negative terminal of car battery7 BackForward Ξ ContentsAluminium wiresMain battery leadAudi has been using aluminium electrical wires for some time now. The Audi A4 (type 8W) makes no exception. The battery main lead in the Audi A4 is made of aluminium, like the Audi A8 (type 4H) where this was used for the first time. This lead begins at the main fuse panel as a flexible round cable. On the right hand-side of the luggage compartment well, it is welded onto a flexurally rigid aluminium ribbon cable. This ribbon cable runs along the right-hand side of the vehicle through the rear section of the vehicle and under the rear seat, terminating in the heel panel area. Here it is welded onto a round cable which continues along the inside of the right-hand sill and through the engine bulkhead to the jump starting terminal in the engine bay. If faulty, the aluminium main battery lead can only be replaced completely. There is no provision for repair work.Wiring harnessA new feature of Audi vehicles, beginning with the Audi A4 (type 8W), is the use of aluminium wires with diameters of 2.5 mm2, 4 mm2 and 6 mm2 in certain areas of the wiring harness. This helps save weight in the electrical system. Copper wires with diameters from 1.5 mm2 to 6 mm2 are also used, particularly in areas in which wires are subject to movement, e.g. on the bonnet.Repairing aluminium wires A new tool was developed for the repair of aluminium wires – the wires harness repair kit for aluminium wires VAS 631 001. In addition to a crimping pliers, this repair kit includes a wire stripper and a special crimp connector including heat shrink tubing for wire diameters of 2.5 mm2, 4 mm2 and 6 mm2. As before, copper wires can be repaired using the wiring harness repair kit VAS 1978B. Cut wires can be reconnected using crimp connectors. Repair wires with industrial manufactured contacts are also available.Crimping pliersWire stripperHeat shrink tubing646_087Crimp connector8 BackSpecial crimp connectors are used for the repair of aluminium wires. These connectors ensure strain resistant connection of the aluminium wires. The supplied heat shrink tubing reliably protects the joints against moisture.Forward Ξ ContentsA cut aluminium wire can be reconnected using this crimp connector. If it is necessary to attach a new section of wires, the copper repair wires from repair kit VAS 1978A can be used.Transition zoneInsulation fittingWire crimping sleeve with serrations and additiveCoding for wire diameter in crimping pliersCode for wire diameter (both sides)646_088Challenges in repairing aluminium wires: 1. T he crimp connector must provide a strain resistant connection. To achieve a strain resistant connection with the aluminium wires, the oxide layers on the individual strands of the aluminium wires must be broken. This is achieved by the serrations in the crimp connectors. These serrations are also coated with an additive to provide better corrosion protection. 2. The joint must be sealed.As copper repair wires are used, there is an aluminium wire on one side of the connector and a copper wire on the other side. To prevent electrochemical corrosion, the joint must be reliably protected against corrosion. The heat shrink tubing supplied with the crimp connector is used for this purpose.Oxide layerHeat shrink tubing646_090 646_089Cable strandOxide layer broken by serrations in connectorHeat shrink tubing (heat shrunk)Reference For a detailed description of how to repair aluminium wires, please refer to the Workshop Manual.9 BackForward Ξ ContentsNetworkingInstallation locations of the control unitsSome of the control units shown in the overview are optional and/ or country-specific equipment. For the sake of clarity, not all control units fitted in the vehicle can be shown here. Refer to the current service literature for details of control unit installation positions as well as instructions for installation and removal.J428 J364 J1023J387A27J794J685 J500 J217 E87J844 R242E380J245 J587J764 J898 J285 J527J623 A31 J104J792J1018 J519 J850 J386Key: A27 Right LED headlight power module 1 A31 Left LED headlight power module 1 E87 Front air conditioner/Climatronic operating and display unit E265 Rear air conditioner/Climatronic operating and display unit E380 Multimedia system operating unit J104 ABS control unit J136 Seat and steering column adjustment control unit with memory J217 Automatic gearbox control unit J234 Airbag control unit J245 Sliding sunroof control unit J285 Instrument panel control unit J345 J364 J386 J387 J393 J428 J492 J500 J519 J521 J525 J527 J533 J587 Trailer detector control unit Auxiliary heating control unit Driver side door control unit Front pass. side door control unit Central control unit for comfort/convenience system ACC control unit All-wheel drive control unit Power steering control unit Electrical system control unit Control unit for pass. seat adjustment with memory function Digital sound package control unit Steering column electronics control unit Data bus diagnostic interface Selector lever sensors control unit10 BackForward Ξ ContentsJ927 R78 J769J880 J649J521J492J234J775E265J772 J533 J605J136J648J393 J525 J928 J926 J608 J345 J770646_010J605 J608 J623 J648 J649 J685 J764 J769 J770 J772 J775 J792 Rear hatch control unit Control unit for special vehicles Engine control unit Control unit for rear left information display and operating unit Control unit for rear right information display and operating unit MMI display Electrical steering column lock control unit Audi lane assist control unit Audi lane assist control unit 2 Rear-view camera system control unit Suspension control unit Control unit for active steeringJ794 Information electronics control unit 1 J844 Main beam assist control unit J850 ACC control unit 2 J880 Reducing agent metering system control unit J898 Control unit for windscreen projection J898 (head-up display) J926 Door control unit, rear driver side J927 Door control unit, rear pass. side J928 Surround camera control unit J1018 Control unit for light control, left J1018 Control unit for light control, right R78 TV tuner R242 Front camera for driver assistance systems11 BackForward Ξ ContentsTopologyThe topology shows all control units with connectivity to the bus systems. Some of the control units shown here are optional or countryspecific equipment or are scheduled for rollout at a later date.Flap control control motors 1 – 15Front air conditioner/Climatronic operating and display unit E87Door control unit, rear driver side J926Driver side door control unit J386Fresh air blower control unit J126Humidity sensor in fresh air intake duct G657 Air quality sensor G238Door control unit, rear pass. side J927Front pass. side door control unit J387High pressure sender G65Diagnostic port Seat and steering column adjustment control unit with memory function J136 Rear air conditioner/Climatronic operating and display unit E265Electronic steering column lock control unit J764 Data bus diagnostic interface J533Front pass. seat adjustment control unit with memory J521Seat back fan 1, front left V512Garage door operating unit E284Light switch E1Special vehicle control unit J608Seat cushion fan 1, front left V514Garage door opener control unit J530Wiper motor control unit J400Sliding sunroof control unit J245Seat back fan 1, front right V516Automatic anti dazzle rear view mirror Y7Rain and light detector sensor G397Rear hatch control unit J605Seat cushion fan 1, front right V518Roof electronics control unit J528Humidity sensor G355Heated windscreen control unit J505Trailer detector control unit J345Electrical system control unit J519Anti-theft alarm sensor G578Alarm horn H12Rear hatch power opening control unit J938Interior light moduleInterior light moduleCentral control unit for comfort/convenience system J393Key:Convenience CAN Hybrid CAN Extended CAN Infotainment CAN12Diagnostics CAN FlexRay Modular Infotainment Platform (MIB) CAN LIN bus BackFor presentation reasons, the FlexRay topology does not mirror the actual configuration of the control units. This also applies to the control units connected to the MOST bus.Forward Ξ ContentsControl unit for rear left information display and operating unit J648 Driver side volume control E67 Control unit for rear right information display and operating unit J649 Multimedia system operating unit E380Digital sound package control unit J525TV tuner R78Multimedia system key module E817Information electronics control unit 1 J794Control unit in dash panel insert J285Battery monitor control unit J367MMI display J685Multifunction steering wheel control unit J453Alternator CSelector lever sensors control unit J587Control unit for windscreen projection (head-up display) J898 Surround camera control unit J928orL/H control unit for light control J1018Front camera for driver assistance systems R242Engine control unit J623NOx sender control unit J583Rear-view camera system control unit J772R/H control unit for light control J1023ABS control unit J104Radiator louvre control motor V544NOx sender control unit 2 J881Reducing agent metering system control unit J880 Main beam assist control unit J844Left LED headlight power module 1 A31Power steering control unit J500Radiator louvre control motor 2 V550Particulate sensor G784Right LED headlight power module 1 A27Suspension control unit J775Active steering control unit J792Front left seat belt tensioner control unit J854 Front right seat belt tensioner control unit J855 Seat occupancy recognition control unit J706 Electrical pump 2 for gearbox V553Audi side assist control unit J769Steering column electronics control unit J527 Operating unit 1 for drive and comfort/ convenience functions E791 ACC control unit J428Airbag control unit J234Audi side assist control unit 2 J770ACC control unit 2 J850Auxiliary heating control unit J364All-wheel drive control unit J492Automatic gearbox control unit J217Remote control receiver for auxiliary heating R64 646_003Sub-bus systems MOST bus LVDS FBAS"OR" configuration Ethernet port for diagnose interface VAS 615413 BackForward Ξ ContentsBus systems used on the Audi A4Bus system Hybrid CAN Convenience CAN Extended CAN Infotainment CAN Modular Infotainment Platform (MIB) CAN Diagnostics CAN FlexRay MOST bus Cable colour Configuration Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Fibre-optic bus system Max. data transfer rate 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 10 Mbit/s 150 Mbit/s Property not single wire capable not single wire capable not single wire capable not single wire capable not single wire capable not single wire capable not single wire capable Ring structure: an open circuit will result in total system failure single wire capable not single wire capable not single wire capable single wire capableLIN bus Sub-bus system LVDS FBASElectrical single-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical single-wire bus system20 kbit/s 500 kbit/s approx. 200 Mbit/s approx. 80 Mbit/sThe network diagram on page 12 provides a schematic overview of the communication paths between the control units in the Audi A4. As a further member of the MLBevo family, the Audi A4 (type 8W) cannot deny its close affinity to the Audi Q7 (type 4M) in the area of control unit networking. The bus systems used in the Audi A4 are identical to those of the Audi Q7 (type 4M).If we compare the Audi A4 (type 8W) with the Audi A4 (Typ 8K), new features in the area of data transmission are the FlexRay, MOST150 and LVDS buses. In spite of the many similarities with the Audi Q7 (type 4M), there are a few differences that are not exclusively equipment-specific. For this reason, the topologies in the areas of infotainment and FlexRay are described below.Infotainment topologyIn the Audi A4 up to 4 control units are integrated in the MOST ring in the following order: • Information electronics control unit 1 J794 • Control unit in dash panel insert J285 • TV tuner R78 • Digital sound package control unit J525 If we compare this with the Audi Q7 (type 4M), the difference is that the DVD changer is absent from the MOST ring in the Audi A4. Volume control E67 is configured as the LIN slave on the control panel E380. In models with manual gearbox, the operator control module for multimedia system E817 is additionally connected. Control units J648 and J649 have been added to the MIB CAN and will be also be featured in the Audi Q7 (type 4M) after the launch of the Audi A4.J525 R78J648E67J649E817E380J794J285J685J587J898J533orJ928Key: Infotainment CAN Modular Infotainment Platform (MIB) CAN LIN bus MOST bus LVDS FBAS Ring break diagnostics line "OR" configurationJ772 646_051Reference For further information and general descriptions of the MOST150 and FlexRay buses, refer to Self Study Programme 634 "Audi Q7 (type 4M) Onboard Power Supply and Networking".14 BackForward Ξ ContentsFlexRay topologyThe data bus diagnostic interface J533 is the controller for the FlexRay bus. All FlexRay control units are connected to J533 via various branches. In this configuration J533 is referred to as the "active hub" or "active node". If only one control unit is connected to a branch, this is referred to as a "point to point" connection. A configuration in which more than one control unit is connected to a branch is known as a "daisy chain connection". In the Audi A4 six branches are used: branches 1 – 5 and branch 8. The pins of branches 6 and 7 are reserved in the current version of J533, but are still not assigned. The following figure is a schematic diagram showing how the control units are connected.ABS control unit J104 Engine control unit J623Power steering control unit J500 Automatic gearbox control unit J217Steering column electronics control unit J527 Front camera for driver assistance systems R242 Suspension control unit J775Branch 1Data bus diagnostic interface J533Branch 2Branch 3Branch 4Branch 5ACC control unit 2 J850Branch 8Active steering control unit J792Airbag control unit J234ACC control unit J428All-wheel drive control unit J492 646_052The next figure shows the actual situation. In configuring of the control units, a distinction is made between the bus positive cable (pink) and the bus negative cable (green). Two resistors each having a resistance of 47 Ω (94 Ω in total) are always connected at the beginning and end of a branch. Each of the so-called "centre control units" has two resistors with a resistance of 1.3 Ω, i.e. 2.6 Ω in total.A control unit from the vehicle's standard specification is always connected at the end of a branch. This ensures that there is a resistance of 94 Ω at the end of each branch. Two optional control units, which are integrated in other models as "centre control units", are connected to branch 8 in the Audi A4. The FlexRay line is, therefore, routed back to the data bus diagnostic interface J533. The resistance here is 94 Ω - the value required for the termination of branch 8.J10447 Ω 47 ΩJ50047 Ω 47 ΩJ52747 Ω 47 ΩJ6231.3 kΩ 1.3 kΩJ2171.3 kΩ 1.3 kΩR2421.3 kΩ 1.3 kΩJ7751.3 kΩ 1.3 kΩBranch 147 Ω 47 Ω 47 Ω 47 ΩBranch 2J53347 Ω 47 Ω 47 Ω 47 Ω 47 Ω 47 ΩBranch 347 Ω 47 Ω 47 Ω 47 ΩBranch 4Branch 51.3 kΩ 1.3 kΩBranch 81.3 kΩ 1.3 kΩJ850J79247 Ω47 Ω47 Ω47 Ω1.3 kΩ 1.3 kΩJ234J428J492646_053 15 BackForward Ξ ContentsControl unitsBrief descriptionsElectrical system control unit646_012Connector C (54-pin) to cockpit wiring harnessConnectors A and B (each 73-pin) to vehicle / engine bay16 BackDesignation Equipment Installation location Tasks Electrical system control unit J519 / also referred to as BCM1 (Body Control Module 1) Always fitted On A post, L/H side, above bonnet release lever (installation location is always on the L/H side, even in RHD models) Exterior lighting master Interior lighting master Diagnostic gateway for the light control unitsForward Ξ ContentsA/C functions • Activation of seat heater and front seat ventilation • Activation of air conditioning compressor without regulating valve N280 and solenoid coupling for air conditioning system N25 Integration functions • Parking • Parking aid • Park assist steering • Activation of front and rear acoustic signal generators • Ambient lighting • Activation and supply of LIN interior light modules • Headlight range adjustment • Calculation of headlight range adjustment • Activation of headlight range adjustment via the left and right control units for light control J1018 and J1023. • Read-in of the signals from the inclination sensor via the CAN line Other functions • Reading (senders/sensors/switches) • Ambient temperature • New engine coolant, windscreen washer fluid, brake fluid • Brake pad wear • Bonnet contact • Seater heater temperature • Activation (actuators/control elements) • Relay for sockets • Signal horn • Headlight washer system • Windscreen washer pump (dual pump) • Heating the windscreen washer jets • Seat heater, front Diagnostic address Data bus communication 09 • Convenience CAN subscribers • J519 is the LIN master for • LIN 1: Light switch E1, wiper motor control unit J400, combined sensor – rain and light detection sensor G397 and humidity sensor G355 • LIN 2: Garage door operating unit E284, garage door operation control unit J530, automatic anti dazzle rear view mirror Y7, roof electronics control unit J528 • LIN 3: Front left seat back fan 1 V512, front left seat cushion fan V514, front right seat back fan 1 V516, front right seat cushion fan V518 • LIN 4: Operating unit 1 for drive and comfort/convenience functions E791 • LIN 5: Interior light module • LIN 6: Interior light module • Communicates via a sub-bus system with the L/H and R/H control units for light control J1018 and J1023 and left and right LED headlight power modules 1 A31 and A27 Fault finding notes: J519 has duplicated pins at the LIN slave connection. For example, LIN 1 is distributed to 3 pins (A22, A23,C50), which, however, are connected internally within the control unit. This means that the control units connected to pin A23 and C50 are also affected in the event of a short circuit to positive or negative at pin A22 and vice versa.Special feature17 BackForward Ξ ContentsGatewayDesignation Equipment Installation location Tasks Data bus diagnostic interface J533 Always fitted Under the rear seat, on the floor pan • • • • • 19 • Hybrid CAN, convenience CAN, Infotainment CAN, CAN-Extended and FlexRay user • LIN master of battery monitor control unit J367 and alternator C • LIN master for multifunction steering wheel control unit J4531) • Not a user of the Modular Infotainment Platform (MIB) CAN • Not a user of the MOST bus • Additional variant as "connected gateway" Network system gateway Controller for FlexRay bus Diagnostic master Energy management control unit Interface for various connect servicesDiagnostic address Data bus communicationSpecial features646_011Data bus diagnostic interface J5331)Optional equipment18 BackForward Ξ ContentsCentral control unit for comfort/convenience systemDesignation Equipment Installation location Central control unit for comfort/convenience system J393 / also referred to as BCM2 (Body Control Module 2) Always fitted In luggage compartment on L/H side, behind luggage compartment side trim, under fuse and relay panel (installation location is always on L/H side, even in RHD models) Central locking system master Integration functions • Terminal management system • Entry and start authorisation • Immobiliser (master) • Anti-theft alarm system Other functions • Reading (senders/sensors/switches) • Brake light switch • Ignition starter button • P signal • Soft touch button on rear hatch • Rear hatch contacts (prelock and full lock) • Rear window breakage sensor • Capacitive sensors of door handles • Entry and start authorisation aerials • Fuel tank sender • Inclination sensors for headlight range adjustment • Hall effect sensor, rear roller blind • Activation (actuators/control elements) • Rear hatch lock motor • Luggage compartment release • Fuel tank flap lock • Rear roller blind motor (Avant only) • Terminal 15 relay • Heated rear window relay • Rear wiper motor (Avant only) • Supply voltage, rear hatch power opening control unit • Luggage compartment lights • Rear lighting Diagnostic address Data bus communication 46 • Convenience CAN subscribers • J393 is the LIN master for: • LIN 1: Control unit for windscreen heater J505, antitheft alarm system sensor G578 • LIN 2: Alarm horn H12 • LIN 3: Rear hatch power opening control unit J938 • J393 is the immobiliser system master in the Audi A4 • Central locking aerial is integrated in the control unit PCBTasksSpecial featuresCentral control unit for comfort/convenience system J393646_013 19 BackForward Ξ ContentsDoor control unitDesignation Equipment Installation location Tasks Driver side door control unit J386 Always fitted In driver's door Controlling the electrical and electronic components in and on the driver's door • Reading (senders/sensors/switches) • Switches/buttons, e.g. for window lifters, rear hatch release, electrical child lock button, electrical door mirror, central locking, seat memory etc. • Activation (actuators/control elements) • Lights and components in and on the door trim, locking and safe motor, turn signals in door mirror 42 • Convenience CAN subscribers • LIN master for door control unit, rear driver side J926 The door control unit, rear driver side J926 has its own address code "BB" although it is a LIN slave of J386.Diagnostic address Data bus communication Special featureDriver side door control unit J386646_014Designation Equipment Installation location TasksFront passenger side door control unit J387 Always fitted In front passenger's door Controlling the electrical and electronic components in and on the front passenger's door • Reading (senders/sensors/switches) • Switches/buttons, e.g. for window lifters, rear hatch release, electrical child lock button, electrical door mirror, central locking, seat memory etc. • Activation (actuators/control elements) • Lights and components in and on the door trim, locking and safe motor, turn signals in door mirror 52 • Convenience CAN subscribers • LIN master for door control unit, rear passenger side J927 The door control unit, rear passenger side J927 has its own address code "BC" although it is a LIN slave of J387.Diagnostic address Data bus communication Special feature20 BackForward Ξ ContentsSeat adjustmentDesignation Equipment Installation location Tasks Diagnostic address Data bus communication Special feature Seat and steering column adjustment control unit with memory J136 Optional equipment (PR no.: PV3) Below the driver's seat Activation (actuators/control elements) • Seat adjustment (memory function) 36 Convenience CAN subscribers Contrary to what the name of the control unit in the "mummy list" would suggest, an electrical steering wheel lock is not available in the Audi A4.Seat and steering column adjustment control unit with memory function J136646_015Designation Equipment Installation location Tasks Diagnostic address Data bus communicationControl unit for passenger seat adjustment with memory function J521 Optional equipment (PR no.: PV3) Below the front passenger seat (not shown) Activation (actuators/control elements) • Seat adjustment (memory function) 06 Convenience CAN subscribers21 BackForward Ξ ContentsTrailer detectorDesignation Equipment Installation location Tasks Trailer detector control unit J345 Optional equipment (PR no.: 1D9) In luggage compartment, L/H side, behind luggage compartment side trim Interconnects the in-car electrics and the trailer electrics • Reading (senders/sensors/switches) • Brake light switch • Tow bar release button • Activation (actuators/control elements) • Tow bar warning lamp • Tow bar lowering motor 69 Convenience CAN subscribers Although the tow bar can be unlocked via a switch in the left luggage compartment trim, it must be moved into its end position by hand until it audibly engages.Diagnostic address Data bus communication Special featureTrailer detector control unit J345646_016Steering column lock control unitDesignation Equipment Installation location Task Diagnostic address Data bus communication Special features Electronic steering column lock control unit J764 • Always installed in vehicles with a manual gearbox • In the case of vehicles with an automatic gearbox, installation is country-dependent On steering column Locking and unlocking the steering column 2B Convenience CAN subscribers • Immobiliser user • Can be replaced separately from the steering columnElectronic steering column lock control unit J764646_017 22 BackForward Ξ ContentsSliding sunroof control unitDesignation Equipment Installation location Tasks Sliding sunroof control unit J245 Optional equipment (PR no.: 3FU) On sliding sunroof frame at front Controlling the functions of the panoramic glass sunroof • Reading (senders/sensors/switches) • Controller for sliding sunroof adjustment • Activation (actuators/control elements) • Motors for sliding sunroof V1 and sliding sunroof roller blind V260 CA Convenience CAN subscribersDiagnostic address Data bus communicationSliding sunroof control unit J245646_018Rear hatch control unitDesignation Equipment Installation location Tasks Rear hatch control unit J605 For Avant only On roof cross member, rear centre Controlling the functions of the electrical rear hatch • Reading (senders/sensors/switches) • Button for closing the rear hatch • Activation (actuators/control elements) • Rear hatch drive motors • Luggage compartment cover motor1) 6D Convenience CAN subscribers The rear hatch control unit activates the rear parking aid speaker.Diagnostic address Data bus communication Special featureRear hatch control unit J605646_0191)Optional "electrical luggage compartment cover" (PR no.: PKC) 23 BackForward Ξ ContentsInterface control unitDesignation Equipment Installation location Task Diagnostic address Data bus communication Special vehicle control unit J608 Optional equipment (PR no.: e.g.: F4X paramedic version, F4G police version etc.) In luggage compartment, L/H side, behind luggage compartment side trim J608 serves as an interface between special installations, e.g. for paramedics, police, fire service etc., and the vehicle electrics 3D Convenience CAN subscribersSpecial vehicle control unit J608646_085Instrument clusterDesignation Equipment Installation location Task Diagnostic address Data bus communication Control unit in dash panel insert J285 • Always fitted • Optional Audi virtual cockpit (PR no.: 9S8) In dash panel Display of information relevant to the driver 17 • Infotainment CAN bus user • MOST subscriber • Connected by LVDS bus to information electronics control unit 1 J794 (image transfer for navigation display in instrument cluster). The instrument cluster in the Audi A4 is not integrated in the immobiliser.Special feature646_020646_086Control unit in dash panel insert J285Control unit in dash panel insert J285 (Audi vitual cockpit)24 BackForward Ξ ContentsACC adaptive cruise controlDesignation Equipment ACC control unit J428 Optional equipment: • ACC with Stop&Go including traffic jam assist (PR no.: 8T8) • ACC distance indicator (PR no.: 8T3) On lock carrier, front right, behind front bumper cover • Radar scanning of traffic (distance and speed) • Controlling speed and distance • Distance display and distance warnings (only if ACC is deactivated) 13 FlexRay subscriber • ACC Stop&Go with integrated traffic jam assistant • Distance display and distance warning – display of distance in instrument cluster in seconds • Function master for ACC control unit 2 J850Installation location TasksDiagnostic address Data bus communication Special features646_021ACC control unit J428ACC control unit 2 J850Designation Equipment Installation location Task Diagnostic address Data bus communication Special featureACC control unit 2 J850 Optional equipment On lock carrier, front left, behind front bumper cover Radar scanning of traffic (distance and speed) 8B FlexRay subscriber ACC control unit 2 is a slave of the ACC control unit J428 and, based on its function, could also be referred to as a sensor.25 BackForward Ξ ContentsMain beam assistDesignation Equipment Installation location Task Diagnostic address Data bus communication Special features Main beam assist control unit J844 Optional equipment (PR no.: 8G1) In rear view mirror Automatic activation and deactivation of main beam in response to oncoming traffic 20 Extended CAN subscriber • J844 can only change over the dipped/main beam headlights. The front camera for driver assistance systems R242 is required for Audi matrix LED headlights. • Only installed if the customer has ordered main beam assist without further assistance systems, such as Audi active Lane Assist or traffic sign recognition.Main beam assist control unit J844646_022Front cameraDesignation Equipment Installation location Tasks Front camera for driver assistance systems R242 Optional equipment On windscreen above base of rear view mirror Imaging of traffic, traffic signs and lane markers for • Audi active lane assist (lane departure warning system) • Main beam assist • Road sign recognition • ACC Stop&Go • Audi pre sense • Evasion assist • Matrix Beam headlight A5 • FlexRay subscriber • R242 is connected to the light control units via a sub-bus system. • Forms a functional unit in combination with image processing control unit • The Audi Matrix LED headlights are also calibrated using the front camera for driver assistance systems R242.Diagnostic address Data bus communication Special featuresFront camera for driver assistance systems R242646_023 26 BackForward Ξ ContentsAutomatic gearboxDesignation Equipment Automatic gearbox control unit J217 Installed in combination with: • 7-speed dual clutch gearbox 0CK/0CL – S tronic (PR no.: G1C/G1D) • 8-speed automatic gearbox 0D5 – tiptronic (PR no.: G1G) Component part of mechatronic unit J743 of automatic gearbox Controlling and monitoring the engagement and disengagement operations of the automatic gearbox 02 • FlexRay subscriber • LIN master for electrical pump 2 for gearbox V553 (in conjunction with 7-speed S tronic) Immobiliser userInstallation location Task Diagnostic address Data bus communication Special featureAutomatic gearbox control unit J217 (7-speed dual clutch gearbox 0CK/0CL)646_047Automatic gearbox control unit J217 (8-speed automatic gearbox 0D5)646_024Reference For further information about the automatic gearboxes, refer to Self Study Programme 644 "Audi A4 (type 8W)".27 BackForward Ξ ContentsSelector mechanismDesignation Equipment Selector lever sensors control unit J587 Installed in combination with: • 7-speed dual clutch gearbox 0CK/0CL – S tronic (PR no.: G1C/G1D) • 8-speed automatic gearbox 0D5 – tiptronic (PR no.: G1G) Within the selector mechanism Operating the automatic gearbox, e.g. transmitting drive positions, controlling the mechanical selector lever locks, transmitting selector lever tiptronic commands and resetting the selector lever in the automatic gate. 81 Infotainment CAN bus user • J587 can only be replacded together with the selector mechanism. • The selector mechanism is not mechanically connected to the automatic gearbox.Installation location TasksDiagnostic address Data bus communication Special featuresSelector lever sensors control unit J587646_025Reference For further information about the selector mechanism, refer to Self Study Programme 644 "Audi A4 (type 8W)".Rear final drive 0D3 – sport differentialDesignation Equipment Installation location Task Diagnostic address Data bus communication Special features All-wheel drive control unit J492 Optional equipment (PR no.: GH2) In luggage compartment Controls the torque of the sport differential's multi-plate clutch 22 FlexRay subscriber • Special procedures must be followed when replacing the control unit. • The driving dynamics control system is integrated in the suspension control unit J775, and no longer in the all-wheel drive control unit J492. All that control unit J492 does is execute the commands issued by J775.All-wheel drive control unit J492646_026 28 BackForward Ξ ContentsSteering column electronicsDesignation Equipment Installation location Task Diagnostic address Data bus communication Special feature Steering column electronics control unit J527 Always fitted On steering column Connects the steering column stalk and the electrical components in the steering wheel to the vehicle's electronics. 16 FlexRay subscriber In conjunction with the multifunction steering wheel, it transfers the LIN signals from the data bus diagnostic interface J533 (master) to the multifunction steering wheel control unit J453 (slave).Steering column electronics control unit J527646_027AirbagDesignation Equipment Installation location Tasks Airbag control unit J234 Always fitted Under centre console, front, on centre tunnel • Deployment of airbags, seat belt pretensioners and battery isolation igniter • Audi pre sense • Deployment of the pedestrian protection system 15 • FlexRay subscriber • Is connected to the front left (J854) and front right (J855) seat belt pretensioner control units via a sub-bus system. • LIN master for seat occupancy recognition control unit J706 (for North American market only) Inertial sensors for ESCDiagnostic address Data bus communicationSpecial featureAirbag control unit J234646_028 29 BackForward Ξ ContentsEngine control unitDesignation Equipment Installation location Tasks Engine control unit J623 Always fitted In engine bay, L/H side, in front of plenum chamber • Controlling the engine characteristic • Activation of starter relays J906 and J907 • Function master for start-stop system 01 • FlexRay subscriber • J623 is connected to NOx senders and the particulate sensor (diesel engine) via a sub-bus system. • LIN master for radiator lourvre control motors 1 and 2 V544 and V550 • Immobiliser user • Control unit with new plug-in connections. Has a total of 315 pins. New test adapter VAS 6606/23 for test box VAS 6606Diagnostic address Data bus communicationSpecial featuresEngine control unit J623646_030Start-stop systemAs with all Audi models with start-stop system, the engine control unit J623 is the coordinator for the start-stop function in the Audi A4. The Audi A4 (type 8W) is equipped with a start-stop system in Version 2.0, which was first used in the Audi Q7 (type 4M). For a history of the start-stop system and a detailed description of Version 2.0, refer to SSP 634 "Audi Q7 (type 4M) Onboard Power Supply and Networking".Operating unit 1 for drive and comfort/convenience functions E791646_080Start-stop mode button E69330 BackForward Ξ ContentsSCR systemDesignation Equipment Installation location Task Diagnostic address Data bus communication Special feature Reducing agent metering system control unit J880 Always installed in diesel models On the underside of the SCR tank Controlling the injection of reduction agent for reduction of the nitrous oxides in the exhaust gases AC Extended CAN subscriber The control unit is identical in all diesel models. The size of the reduction agent tank can vary: standard SCR tank capaciity 12 l; "extended range" SCR tank capacity 24 l1).Reducing agent metering system control unit J880646_031Front A/C control panelDesignation Equipment Front air conditioner/Climatronic operating and display unit E87 Always fitted • Automatic air conditioning (PR no.: 9AK) • Automatic air conditioning (PR no.: 9AQ) In centre of dash panel Controlling: • Temperature • Fan speed • Air flow distribution 08 • Hybrid CAN user • E87 is the LIN master for • LIN 1: Control motors for flap activation 1 – 15 • LIN 2: Rear air conditioner/Climatronic operating and display unit E265, fresh air blower control unit J126, humidity sensor in fresh air intake duct G657, air quality sensor G238, high pressure sensor G65 Although the seat seating and seat ventilation switches are integrated in and read in by operating unit E87, the electrical system control unit J519 is responsible for their activation.Installation location TasksDiagnostic address Data bus communicationSpecial featureFront air conditioner/Climatronic operating and display unit E87 (figure shows deluxe automatic air conditioning system)646_0291)Optional equipment31 BackForward Ξ ContentsHead-up displayDesignation Equipment Installation location Task Diagnostic address Data bus communication Special features Control unit for windscreen projection (head-up display) J898 Optional equipment (PR no.: KS1) In dash panel, directly in front of instrument cluster Controlling all optical, mechanical and electrical components of the head-up display 82 Infotainment CAN bus user • The control units can only be replaced complete with the other components of the head-up display. • To replace the head-up display, the windscreen must be removed. • When replacing the windscreen, please note: the head-up display requires a special screen (with wedge-shaped foil).646_032Control unit for windscreen projection (head-up display) J89832 BackForward Ξ ContentsRear-view cameraDesignation Equipment Installation location Task Diagnostic address Data bus communication Special feature Rear view camera system control unit J772 Optional equipment (PR no.: KA2) In handle (soft touch) on rear hatch Processing and transfer of images from the area behind the vehicle to the information electronics control unit 1 J794 6C Extended CAN subscriber Control unit, camera and wiring harness form a unit (as shown)Rear-view camera system control unit J772 (with built-in camera)646_033Surround camerasDesignation Equipment Surround camera control unit J928 Optional equipment, available in combination with: • Parking aid plus (PR no.: 7X2) • Park assist (PR no.: 7X5) In luggage compartment, L/H side, behind luggage compartment side trim The control unit reads in the data from the 4 surround-view cameras and generates images mapping the area around the vehicle. 6C • Extended CAN subscriber • Image transfer to instrument cluster by LVDSInstallation location Task Diagnostic address Data bus communicationSurround camera control unit J928646_034 33 BackForward Ξ ContentsAuxiliary heatingDesignation Equipment Installation location Tasks Auxiliary heater control unit J364 Optional equipment (PR no.: 9M9) In front wheel arch, R/H side, on side member • Reading (senders/sensors/switches) • Temperature sensor, flame monitor • Switch-on signals of auxiliary heating radio receiver • Activation (actuators/control elements) • Fuel metering pump, combustion air blower • Heater glow plug, heating element for fuel preheating • Coolant circulation pump, heater coolant shut-off valve 18 • Extended CAN subscriber • LIN master for auxiliary heating radio receiver R64 Control unit integrated in heaterDiagnostic address Data bus communication Special featureAuxiliary heating control unit J364646_03534 BackForward Ξ ContentsAudi side assistDesignation Equipment Installation location Tasks Audi side assist control unit J769 (master) Audi lane assist control unit 2 J770 (slave) Optional equipment (PR no.: 7Y1) In rear bumper cover, left and right Radar monitoring system for the detection of vehicles (cycles and automobiles) in the area to the rear and side of the vehicle for • Audi pre sense rear including Audi side assist • Rear cross traffic assist • Exit warning • 3C – J769 (master) • CF – J770 (slave) • Extended CAN subscriber • Both control units are also interconnected by a sub-bus system. The control unit is integrated in the bumper cover. The system has to be calibrated after removal and installation.Diagnostic address Data bus communication Special featureAudi side assist control unit J769Audi side assist control unit 2 J770646_03635 BackForward Ξ ContentsElectronic Stability Control (ESC)Designation Equipment Installation location Tasks ABS control unit J104 Always fitted In engine bay, L/H side Controlling: • Anti lock braking system (ABS) • Electronic Stability Control (ESC) • Traction Control System (TCS) • Electronic Differential Lock (EDL) • Torque vectoring • Multicollision brake • Electro-mechanical parking brake (EPB) 03 FlexRay subscriber • The control unit camn be replaced separately from the valve block. ESD protective mat VAS 6613 must be used. • The electro-mechanical parking brake is integrated in the ABS control unit. Address word 53 is no longer used for electro-mechanical parking brake.Diagnostic address Data bus communication Special features646_037ABS control unit J10436 BackForward Ξ ContentsInformation electronicsDesignation Equipment Installation location Task Diagnostic address Data bus communication Information electronics control unit 1 J794 Always fitted In glove compartment Controlling the infotainment systems 5F • Infotainment CAN bus user • MOST subscriber • J794 is connected to the MMI display J685 and the multimedia system operating unit E380 via the Modular Infotainment System (MIB) CAN. • J794 is the system manager and the ring break diagnostics master for the MOST bus. • J794 is connected to the dash panel insert control unit J285 and the MMI display J685 via LVDS bus (image transfer for navigation display in instrument cluster or MMI display).Special featuresInformation electronics control unit 1 J794646_038Information electronics control unit 1 J794 (back)TV tunerDesignation Equipment Installation location Task Diagnostic address Data bus communication TV tuner R78 Optional equipment (PR no.: QV1) In luggage compartment, R/H side, behind luggage compartment side trim TV reception 57 MOST subscriberTV tuner R78646_03937 BackForward Ξ ContentsSound amplifierDesignation Equipment Installation location Task Diagnostic address Data bus communication Digital sound package control unit J525 Optional equipment (PR no.: 9VS) In luggage compartment, L/H side, behind luggage compartment side trim Activation of up to 19 speakers 47 MOST subscriber646_040Digital sound package control unit J52538 BackForward Ξ ContentsRear Seat Entertainment (Audi tablet)Designation Equipment Installation location Task Diagnostic address Data bus communication Control unit for rear left information display and operating unit J648 Optional equipment (PR no.: 9WE or 9WF) In the driver seat backrest Interface between the Audi tablet for Rear Seat Entertainment, rear left and the vehicle electronics 5E Modular Infotainment System CAN subscriberBracket for multimedia system display unit 3 R315Control unit for rear left information display and operating unit J648646_041Designation Equipment Installation location Task Diagnostic address Data bus communicationControl unit for rear right information display and operating unit J649 Optional equipment (PR no.: 9WE or 9WF) In the front passenger seat backrest Interface between the Audi tablet for Rear Seat Entertainment, rear right and the vehicle electronics 4E Modular Infotainment System CAN subscriber39 BackForward Ξ ContentsSuspension control unitDesignation Equipment Installation location Tasks Suspension control unit J775 Optional equipment Under centre console, front, on centre tunnel Wheel damping control • Reading (senders/sensors/switches) • Level control system sensor (4 pcs.) • Activation (actuators/control elements) • Damper adjustment valve (4 pce.) 74 FlexRay subscriber The suspension control unit J775 is responsible for driving dynamics control. In models with a sport differential, J775 sends the commands to the all-wheel drive control unit J492, where these commands are put into action.Diagnostic address Data bus communication Special featureSuspension control unit J775646_042Power steeringDesignation Equipment Installation location Tasks Power steering control unit J500 Always fitted Connected to the steering gear. Controlling: • power steering • Servotronic speed-responsive power steering • Corrective steering inputs in conjunction with Audi active lane assist, park assist, evasion assist and trailer assist • Corrective steering inputs in conjunction with ESC 44 FlexRay subscriber The control unit with power steering motor can only be replaced together with the steering gear.Diagnostic address Data bus communication Special featurePower steering control unit J500646_043 40 BackForward Ξ ContentsDynamic steeringDesignation Equipment Installation location Tasks Active steering control unit J792 Optional equipment (PR no.: 1N8) In driver's side footwell, under the floor covering • Calculating the superimposition angle required to implement the variable steering ratio. • Correcting the calculated superimposition angle of the stabilising function through ESC intervention. • Reading (senders/sensors/switches) • Index sensor • Motor position sensor • Activation (actuators/control elements) • Dynamic steering actuator • Dynamic steering lock 1B FlexRay subscriber Basic setting is necessary after: • replacement by a new or different active steering control unit J792 • replacement by a new or different steering column • replacement by a new or different steering angle sensor G85 or recalibration • Changing the wheel alignment values • Disconnecting the actuator from the steering column or the actuator from the steering gearDiagnostic address Data bus communication Special features646_044Active steering control unit J79241 BackForward Ξ ContentsExterior lightingHeadlight variantsIn the case of the Audi A4, a distinction is made between the following headlight versions:• Xenon headlight (ECE1) and SAE2)) • LED headlight (ECE1) and SAE2)) • Audi Matrix LED headlight (ECE1))To remove headlights, the bumper cover must be taken off beforehand. The headlights are connected to the vehicle body by means of adjusting elements. Thus, it is possible to align the headlights exactly with the other body parts. Before the headlight can be removed from the vehicle, the headlight washer nozzle must be unclipped from the headlight.In the event of damage to the upper and inner headlight attachments, repair tabs can be attached to the headlight housing. The parts marked "Service" in the exploded-view diagrams of the headlights on the following pages can be replaced individually in the event of damage. For information as well as the corresponding spare part numbers, please refer to the workshop manual or the electronic parts catalogue.Xenon headlightThe figure shows the left headlight in the ECE1) version.Sealing cover in headlight housing – access for changing bulb in foglight "Service"Headlight range control servomotor V48Reflectors for LED daytime running light and side lightTurn signal bulb, front left M5 "Service"Left gas discharge lamp L13 "Service"Fog light bulb, left L22 "Service"1) 2)646_054ECE = for European market SAE = for North American RegionNote "Fog light bulb L22" (for the all-weather light function) can be accessed via a cover on the back of the headlight housing and can be replaced after the headlight has been installed.42 BackForward Ξ ContentsLED headlightsThe figure shows the left headlight in the ECE1) version.Headlight range control servomotor V48Power module 1 for left LED headlight A31 "Service"Headlight moduleControl unit for light control, left J1018 "Service" Dipped beam moduleFibre optic cable for daytime running light / side light, turn signal646_055Audi Matrix LED headlightThe figure shows the left headlight.Headlight range control servomotor V48Power module 1 for left LED headlight A31 "Service"Left headlight fan V407Matrix headlight moduleControl unit for light control, left J1018 "Service" Dipped beam moduleFibre optic cable for daytime running light / side light, turn signal646_0561) 2)ECE = for European market SAE = for North American RegionReference For information on parts replaceable by service centres and the corresponding spare part numbers, please refer to the workshop manual or the electronic parts catalogue.43 BackForward Ξ ContentsXenon headlightThe figure shows the L/H headlight in the ECE1) version.Daytime running light/ parking light Dipped beam/ main beam646_057Turn signalAll weather lightLight functions Daytime running light Side light Dipped beam Motorway light (only ECE1)) Main beam All weather light Turn signal Sidemarker (SAE only2))Type of bulb used 4 LEDs Parking light is dimmed if light function is active Gas discharge lamp D5S Raises dipped beam by means of headlight range adjustment Changes over dipped beam using shutter Bulb H8 Bulb PSY24W 1 LEDPower 5 watts25 watts35 watts 24 watts 0.5 wattsSpecial features of the light functions The daytime running lights in the ECE1) version are dimmed for the duration of the turn signaling cycle (in the SAE2) version they are switched off). The all-weather light in both versions is deactivated during the turn signalling cycle as soon as the vehicle exceeds a speed of 40 kph. The left and right dipped beam shutter motors V294 and V295 are used for switching between dipped beam and main beam. The LEDs for the side light function and the dipped beam function of the gas discharge lamp are used for the Coming Home / Leaving Home function.1) 2)ECE = for European market SAE = for North American Region44 BackSchematic diagram of the activation mechanismForward Ξ ContentsGas discharge headlight (L/H side of vehicle)Electrical system control unit J519 • Voltage supply • Activation of light functions • Calculation/activation of headlight range adjustmentDiscrete linesConvenience CAN• Control unit • Dipped beam shutter • Fog light bulb, left • Turn signal bulb, front left • LEDs for parking lights and daytime running lights • LEDs for front left side marker light (SAE2)) • Beam-height adjustment servo motor646_058Activation If the vehicle is equipped with xenon headlights, the electrical system control unit J519 is responsible for power supply as well as for activating all bulbs in the headlight. J519 also activates the dipped beam shutter and the headlight range adjustment control motor. Headlight range adjustmentService The basic setting of the headlight range adjustment function is configured in the electrical system control unit J519. The foglamp bulb can be replaced with the headlights fitted. This bulb can be accessed via a cover on the back of the headlight housing. The headlight must be removed in order to replace the gas discharge lamp or the turn signal lamp. Adaptation for driving on the opposite side of the roadThe gas discharge headlight has automatic static headlight range adjustment. This means that changes in headlight range are compensated by loading of the vehicle. However, changes caused by rolling movements of the vehicle under acceleration and braking are not compensated. The electrical system control unit receives information on ride height from either the central control unit for comfort/convenience system J393 or, if installed, the suspension control unit J775.It is not necessary to adapt the headlights. No further action is needed in order to meet the statutory requirements. Optional equipment The xenon h