TECHNICAL DOCUMENTATION
SSP 651 Audi SQ7 (type 4M)

This PDF is currently unavailable.
Read document text
Audi SQ7(type 4M)Self Study Programme 651For internal use onlyAudi Service Training BackThe new Audi SQ7 TDI strikes an impressive balance between powerful and intensified stylistic elements. The Audi DNA, such as the sculpted singleframe radiator grille, distinctively highlighted wheels and flared quattro-style blisters, is unmistakable. Distinguishing features of the SQ7 are the new radiator grille with an S specific design at the bumpers, the side air inlets, the mirror housings and door inlays in aluminium. The exhaust system terminates in four rectangular tailpipes. The SQ7 is driven by a redesigned 4.0l V8 TDI engine. The new technology solution of the electrically powered compressor in the SQ7 is an Audi world first. In addition, two exhaust-gas turbochargers are activated selectively according to the concept of sequential charging. The Audi valvelift system (AVS) is also making its debut in a diesel model from Audi. A redesigned 8-speed tiptronic takes care of power transmision to the wheels.Forward Ξ ContentsAudi offers the SQ7 TDI with an optional driving dynamics package comprising three technology modules: sport differential, electromechanical active roll stabilisation and all-wheel steering. The standard LED and optional Matrix LED headlights plus the dynamic rear turn signals underscore Audi’s leading role in lighting design and technology. With its 12.3 inch display, the Audi virtual cockpit presents logically structured information in brilliant graphics. Driver ergonomics are excellent, and operation is intuitive. The driver chooses the display mode via the multifunction steering wheel. A head-up display is also available as an option. MMI navigation plus, the top-of-the-line infotainment system in the SQ7 TDI, uses the second-generation Modular Infotainment Platform. Thanks to the integrated LTE module and the Wi-Fi hotspot included in the Audi connect package, passengers can surf at high speed with their mobile devices The Audi connect package brings comprehensive online functions on board.651_002Learning objectives of this self study programme: This self study programme describes the design and functioning of the Audi SQ7 (type 4M). Once you have completed this self study programme you will be able to answer questions on the following topics: • • • • • Engine type 48-volt electrical subsystem New suspension features New power transmission features New features of the assistance systems.2ContentsIntroductionPresentation __________________________________________________________________________________________________________________________________________________ 4 Dimensions ___________________________________________________________________________________________________________________________________________________ 6BodyOverview ______________________________________________________________________________________________________________________________________________________ 8Drive unit4.0l V8 TDI engine _ _________________________________________________________________________________________________________________________________________ 10 Exhaust system _ _____________________________________________________________________________________________________________________________________________ 12Power transmissionOverview _____________________________________________________________________________________________________________________________________________________ 14 8-speed automatic gearbox 0D6 __________________________________________________________________________________________________________________________ 16 quattro with sport differential _ ____________________________________________________________________________________________________________________________ 20 Service _ _______________________________________________________________________________________________________________________________________________________ 24SuspensionOverview _____________________________________________________________________________________________________________________________________________________ 26 Driving dynamics – roll _ ____________________________________________________________________________________________________________________________________ 27 Roll stabilisation – basic principle _________________________________________________________________________________________________________________________ 29 System components ________________________________________________________________________________________________________________________________________ 30 Functional principle _________________________________________________________________________________________________________________________________________ 33Electrics and electronicsAudi drive select _ ____________________________________________________________________________________________________________________________________________ 36 General information on the onboard power supply _ ____________________________________________________________________________________________________ 37 Topology _____________________________________________________________________________________________________________________________________________________ 38 Bus systems used on the Audi SQ7 ________________________________________________________________________________________________________________________ 40 48-volt electrical subsystem _______________________________________________________________________________________________________________________________ 42 Convenience electronics ____________________________________________________________________________________________________________________________________ 58Air conditioningVariants ______________________________________________________________________________________________________________________________________________________ 60 In-car components __________________________________________________________________________________________________________________________________________ 61Safety and driver assistance systemsPassive safety ________________________________________________________________________________________________________________________________________________ 62 Driver assistance systems __________________________________________________________________________________________________________________________________ 66Infotainment and Audi connectOverview of versions ________________________________________________________________________________________________________________________________________ 70Inspection and maintenanceOverview _____________________________________________________________________________________________________________________________________________________ 72 Special tools and workshop equipment _ __________________________________________________________________________________________________________________ 74AppendixSelf study programmes _ ____________________________________________________________________________________________________________________________________ 75The self study programme teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a repair manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. This content is not updated. For further information about maintenance and repair work, always refer to the current technical literature.NoteReference3 BackForward Ξ ContentsIntroductionPresentationThe Audi SQ7 is the top model in this series alongside the Q7 and Q7 e-tron quattro. This is underscored by the use of other innovative technologies, such as the electrically powered compressor, the electromechanical active roll stabilistion system and the 48-volt electrical subsystem. Below you will find summarised the key features of the Audi SQ7.Engine4.0l V8 TDI engine with active and passive turbochargers as well as an electrically powered compressor for low engine speeds in particular. • Max. power: 320 kW (435 hp) • Max. torque: 900 NmAssistance systemsThe following systems are optionally available: • Cross-traffic assist • Trailer assist • ACC stop & go including traffic jam assistant • Audi active lane assist • Audi pre sense basic, front, rear and city • Exit warning • Predictive efficiency assist • Night vision assist • Evasion assist • Turning assistSuspensionSuspension system components, such as the links, are largely made of aluminium. Electromechanical power steering, the Audi drive select driving dynamics system and adaptive air suspension with S-specific tuning are standard. Extremely lightweight carbon fibre-ceramic discs will also become optionally available shortly after the market launch. The electromechanical active roll stabilisation system significantly reduces body roll in corners.Displays and operationWith its 12.3 inch display, the Audi virtual cockpit presents logically structured information in brilliant graphics. Driver ergonomics are excellent, and operation is intuitive. The driver chooses the display mode via the multifunction steering wheel. A head-up display is also available as an option. The standard MMI navigation plus with MMI all in touch includes a large glass surface on the centre tunnel console that provides the finger with haptic feedback after each click. The MMI logic allows for intuitive system operation and also understands terms from everyday speech.4 BackForward Ξ ContentsAir conditioningA newly developed, two-zone deluxe air conditioning system is standard. Just a few buttons and dials are sufficient for convenient control. Audi also offers the option of a four-zone system, the temperature displays of which are integrated into the rotary dials.BodyHot-shaped and extremely strong steel sheets form the backbone of the occupant cell. Aluminum castings, extruded sections and panels are used in the front and rear ends as well as the body. Other parts made entirely of aluminum are the doors, the front wings, the bonnet and the rear hatch. A twopiece panoramic glass sunroof is optional.651_003Power transmissionThe newly designed 8-speed tiptronic is outstanding for its high efficiency. It provides extremely fast and efficient gear shifting and allows the vehicle to glide in neutral at higher speeds. A self-locking centre differential is the heart of the quattro full-time all-wheel drive system. It is compact, lightweight and interacts very precisely with the suspension control system.Onboard power supplyThe SQ7 uses a 48-volt electrical subsystem to supply the electromechanical active roll stabilisation system as well as the electrically powered compressor. Energy is stored in a 48-volt lithium-ion battery with 470 watt hours of nominal energy content and a maximum power output of 13 kilowatts.5 BackForward Ξ ContentsDimensions1679 1968651_020174112191679 2212651_021107101 69171 1)9782996 50691095651_0226788/6932) BackForward Ξ Contents15713)15613)15124)14854)12553)12554)1179 1086651_023Exterior dimensions and weightsLength in mm Width (not including exterior mirrors) in mm Width (including exterior mirrors) in mm Height in mm Front track width in mm Rear track width in mm Wheelbase in mm Kerb weight in kg Gross vehicle weight in kg Drag coefficient cw 5069 1968 2212 1741 1679 1679 2996 2345/24055) 3030/32005) 0.34Inner dimensions and other specificationsFront cabin width in mm Front headroom in mm Headroom of 2nd seat row in mm Headroom of 3rd seat row in mm Through-loading width in mm Load sill height in mm Luggage compartment capacity in l Capacity of fuel tank in l 15713) 10711) 1016 917 1086 788/6932) 805/2355) 85Maximum headroom Air suspension at loading height 3) Elbow room width 4) Shoulder room width 5) 5-seater/ 7-seater1) 2)All dimensions are given in millimetres and refer to the unladen weight of the vehicle.7 BackForward Ξ ContentsBodyOverviewThe body of the SQ7 is based on the MLBevo (Modular Longitudinal Matrix Evolution). The lightweight body has a multi-material construction and generally is identical to the body of the Q7 base model.Body featuresFirst and foremost, the exterior of the SQ7 is distinguished from the Q7 base model by a number of exclusive design features that accentuate its appearance. Nonetheless the SQ7 The new Audi SQ7 TDI strikes a good balance between powerful and intensified stylistic elements. The SQ7 is distinguished from the base model by the following features:Radiator louvre As with the Audi Q7 efficiency model, the SQ7 has a radiator louvre whose plastic slats open as required or close to provide better thermodynamic and aerodynamic performance.651_066S line front apron with air intakes and exclusive double louvres in aluminium effectDistinctive single-frame grille with S double struts651_019 651_018SQ7 badge integrated in radiator grilleDoor sill plates with SQ7 logoReference In Self Study Programme 632 "Audi Q7 (type 4M)" you will find detailed information about the body structure of the Q7, the materials used, joining techniques, the radiator louvre and the repair methods. Please refer to the current service literature for the relevant information and specifications.8 BackForward Ξ ContentsAt the rear endRoof spoiler in SQ7 designUpper door mirror caps with an anodised matt aluminium finishSporty rear diffusor with aluminium look and under body protection with vertical struts at the rear end651_017V8T badge on the left and right front wings651_015Inside cabinDoor sill trims in S line design and S line aluminium-effect door inlaySQ7 badge on the centre console and leather-trimmed sport steering wheel651_016Reference The technical background for the area of general body repairs (such as the panoramic glass sunroof, power-operated rear hatch or seat systems) is identical to that of the Q7 base model and is described in greater detail in Self Study Programme 632 "Audi Q7 (type 4M)".9 BackForward Ξ ContentsDrive unit4.0l V8 TDI engineFeatures• Audi valvelift system (AVS) on the intake and exhaust sides • Combined oil/vacuum pump inside the oil pan with fully variable oil delivery rate control • Integrated oil filter built into the oil pan behind a cover • Common NOx oxidation catalyst (NOC) and SCR-coated diesel particulate filter integrated in the inner vee, i.e. near the engine • Common rail injection system which delivers injection pressures of up to 2500 bar • Sequential charger with a combination of an active and passive turbocharger • Electrically powered compressor driven by the 48-volt electrical subsystemSynergy with the 3.0l V6 TDI Gen2 evo• • • • Concept of the timing gear Concept of the cylinder heads Concept of the thermal management system Concept of the single-scroll high-pressure exhaust gas recirculation systemCO2 reduction measures• Innovative Thermal Management (ITM) 2 • Concept of a fully variable oil pump • Friction reduction through the use of coated piston rings and reduced preload • Friction reduction in the exhaust turbocharger rotor • Use of engine oil 0W-20651_006Reference For more information about the 4.0l V8 TDI engine, refer to Self Study Programme 652 "Audi 4.0l V8 TDI engine of EA898 series".10 BackForward Ξ ContentsSpecifications Torque-power curve of 4.0l V8 FDI engine EA898 (engine code CZAC) Power output in kW Torque in Nm651_004The engine code is located at the front left below the cylinder head on the protruding edge of the engine block as seen in the direction of travel.Engine speed [rpm]651_005Features Engine code Type Displacement in cm Stroke in mm Bore in mm Number of valves per cylinder Firing order Compression ratio Power output in kW at rpm Torque in Nm at rpm Fuel type Turbocharging Engine management Maximum injection pressure in bar Exhaust gas treatment Emission standard CO2 emissions in g/km1) 3Specifications CZAC 8-cylinder engine with 90° vee angle 3956 91.4 83.0 4 1-5-4-8-6-3-7-2 16.0 : 1 320 at 3750 - 5000 900 at 1000 - 3250 Diesel to EN 590 Active and passive turbochargers with variable turbine geometry (VTG), electrically powered compressor Bosch CRS 3.25 2500 bar NOC (NOx oxidation catalyst), SCR-coated diesel particulate filter with integrated ammonia slip catalyst EU 6 (ZG) 189 – 1981)Depending on tyre size. 11 BackForward Ξ ContentsExhaust systemExhaust gas temperature sensor 4 (after diesel particulate filter) G648Exhaust gas treatment moduleFlexible pipeParticulate sensor G784NOx sensor 2 G687Exhaust gas treatment moduleExhaust gas temperature sensor 3 after oxidation catalyst G495 NOx accumulator and oxidation catalyst (NOC) Oxygen sensor G39Connecting pipeExhaust gas temperature sender 2 G448 NOx sender G295 Connection to differential pressure sensor G505Exhaust gas temperature sensor 4 (after diesel particulate filter) G648Oxygen sensor after catalytic converter G130651_024Reducing agent injector N474MixerDiesel particulate filter with copper-zeolyte SCR coatingThe diesel particulate filter has a preciousmetal washcoat at the end of the exhaust gas recirculation system12 BackForward Ξ ContentsSound systemThe active sound system is able to produce defined frequencies (engine orders) in order to achieve a desired sound effect. In contrast to conventional exhaust systems with passive silencers, exhaust noise can be adapted to the vehicle and driving situation via Audi drive select. The sound system comprises a sound actuator, an exhaust system with attached speaker housings including actuators R257 and R258 as well as an engine noise generation control unit J943. The control unit receives vehicle data (engine speed, engine load, vehicle type and speed) by CAN bus (powertrain CAN). The signal generator, which is integrated in the engine noise generation control unit J943, produces a spectrum of superimposed oscillations dependent on the engine's operating state. This signal spectrum is amplified by the engine noise generation control unit J943 to produce a power signal and converted to sound waves by the sound actuator. The sound actuator produces the structure-borne sound which is transmitted into the cabin through the body and the front windscreen. It is fitted in a special holder at the centre of the windscreen base. The actuators produce sound waves according to the engine map in the control unit. The sound module is made up of additional speaker housings at the main silencers whose exhaust pipes connect to the tail pipes of the exhaust system.Cutaway view of sound actuatorAssembly bolt with threadElectrical connectionOscillating mass651_064Engine noise generation actuator 1 R257Engine noise generation actuator 2 R258Rear silencer (baffle silencer)651_010Note The tail pipes must not be sealed to carry out leak testing as the backpressure will cause irreparable damage to the speakers.13 BackForward Ξ ContentsPower transmissionOverviewThe quattro drive concept of the Audi SQ7 (type 4M) is based on the proven technology of the modular longitudinal matrix with full-time all-wheel drive. 8-speed automatic gearbox 0D6 for all-wheel drive is rated to match the performance of the Audi SQ7. The front axle drive is located in front of the torque converter. The transfer case incorporates a self-locking centre differential with an asymmetric-dynamic torque split. The rear final drive 0DG is used on the rear axle. The suspension control system "quattro with Sport differential" is optional. Refer to page 20. The software of the 0D6 gearbox utilises the data from the navigation system to assist the start-stop system, neutral idle control and coasting mode. The gearbox setup can be adjusted via Audi drive select. Refer to page 19. The gearbox control unit is integrated in the immobiliser system.4.0l V8 TDI engine8-speed automatic gearbox 0D6. Refer to page 16.The selector mechanism of the Audi SQ7 is identical to the basic version as described in SSP 632, page 40 ff.Coolant shut-off valve N509Splined prop shaftThe ATF cooling system of the 0D6 gearbox is regulated by the coolant shutoff valve N509 in the coolant supply for the ATF cooler. The shut-off valve is actuated by the gearbox control unit J217 which receives the command to open or close the valve from the thermal management system of the engine control unit. The ATF cooling system of the 0D6 gearbox is, therefore, identical to the cooling system of the 0D5 gearbox in the Audi Q7 (type 4M) as described in SSP 632, page 38 ff.The parking lock emergency release mechanism of the Audi SQ7 is identical to the basic version as described in SSP 632, page 48 ff.Splined prop shaftAssembly of the front prop shaftThe prop shaft is connected to the gearbox output shaft by a spline. For more detailed information, refer to SSP 457 and the Audi Service TV programme – STV_0173 _Audi A8 Power Transmission Part 2 / Topic: Splined prop shaft.Clamp651_040 14 BackForward Ξ ContentsRear axle final driveRear axle drive 0DG Rubber-metal bearing Subframe Rubber-metal bearingThe housing of final drive is designed in such a way that it can be mounted to the subframe by means of a four-point mounting system without any additional mountings. The front rubber-metal bearing is press-fitted into the gearcase and bolted to the subframe. It is supported by an additional bearing which acts in the Z direction. The design allows for selective vibration insulation. In the case of all rubber-metal bearings except the additional bearing, the installation position specified in the workshop manual must be observed.GasketRear axle drive 0DG The rear axle drive 0DG is rated to match the performance of the Audi SQ7 and has the internal factory designation HL230.S2.Front rubber-metal bearing651_038Rear axle drive 0BX – sport differential The rear axle drive 0BX – sport differential is a component part of the optional suspension control system "quattro with sport differential". The rear axle drive 0BX – sport differential has the internal factory designation HL220.T2. Please refer to page 20 ff. for further information.Assembly of the rear prop shaftThe procedure for attaching the prop shaft to the rear axle drive is described in the bolting specification for triangular matching. Refer to the Workshop Manual. For detailed information about triangular matching please refer to SSP 409 and the Audi Service TV programme – STV_0154_Audi A5 Power Transmission / Topic: Prop Shaft Assembly ConceptFront rubber-metal bearing Rear axle drive 0DGAdditional bearing651_039 15 BackForward Ξ Contents8-speed automatic gearbox 0D68-speed automatic gearbox 0D6 is a further development of 8-speed automatic gearbox 0BL first used on the Audi A8 (type 4H). see SSP 457 At Audi, the 0D6 gearbox has the internal factory designation AL552-8Q. The manufacturer, ZF-Getriebe GmbH, uses the designation 8HP65A. It is rated for up to 1,000 Nm of input torque.The key new features of the 0D6 gearbox compared with the 0BL gearbox are: • The torque converter with integrated dual mass flywheel with centrifugal pendulum-type absorber. • A reinforced gear set with revised shift elements. Brake B is now activated by a simplex cylinder and the clutch plate assembly of brakes A and B on the Audi SQ7 is configured for active plate separation by using corrugated springs. The separation of the clutch plates helps save fuel and reduces C02 emissions. • The mechatronics with modified hydraulic interfaces and a vehicle plug connection facing in the direction of travel. • A plastic ATF pan with integrated ATF suction filter and an ATF drain screw with bayonet catch in place of a thread. • The combined ventilation of two oil systems, the ATF and the MTF for the transfer case and the front axle drive. Refer to page 18. • The gearbox software enhances coasting mode. • In addition, as previously the case with the 0D6 gearbox, the software of the 0BL gearbox utilises the data of the navigation system and assists the start-stop system by means of a hydraulic impulse storage system, or HIS for short. • The gearbox setup configured using Audi drive select now offers additional modes. These new features were previously used in combination with the 8-speed automatic gearbox 0D5. For further information about this gearbox generation, refer to SSP 632.Clutch DTorque splitThe transfer case of the Audi SQ7 houses a JTEKT self-locking centre differential. This differential has an asymmetric-dynamic torque split and, depending on traction conditions, distributes up to 70 % to the front axle or up to 80 % to the rear axle without deceleration or any need for corrective action by the ESC system (refer to SSP 363 and 478). The mechanical centre differential thus enhances traction and driving dynamics. The torque vectoring system 1) and the optional suspension control system "quattro with sport differential" (refer to page 20) enhance steering agility and driving stability in addition to traction and driving dynamics.Vent for transfer box and front axle driveJTEK self-locking centre differentialTransfer caseInspection and filler screw for the transfer case gear oil1)For more information about torque vectoring, refer to SSP 617. Parking lock with reinforced pawl and enlarged parking lock gear diameter16 BackForward Ξ ContentsBrake A, with active brake disc separationTorque converter with integrated dual mass flywheel with centrifugal pendulum-type absorber. For more information about this technology, refer to SSP 632, page 34.Brake B, with active brake disc separationBreather portClutch CClutch ETorque-optimised tapered roller bearingFront axle driveATF filler and inspection screwPlastic ATF pan with integrated ATF suction filter and an ATF drain screw with bayonet catch in place of a thread.651_04117 BackForward Ξ ContentsOil systems and gearbox ventilationSealing sleeveBreather portCollecting chamberBreather hose for transfer box and front axle driveDistributor housingFront axle driveO-ringATF cooler returnATF cooler intakeBreather pipe651_042The 8-speed automatic gearbox 0D6 has two separate oil systems. The ATF system and the MTF system. The MTF system supplies the front axle drive and the transfer case. Both parts of the gearbox are ventilated through the transfer case. In the Audi SQ7 a breather hose connects the ventilation point of the transfer case and the collecting chamber. The MTF and ATF ventilation systems are merged in the collecting chamber.To ensure that the ventilation system does not flow into the converter housing, it is routed outwards through a tube element to the breather port. This safeguards against the contamination of the converter housing and largely prevents ingress of water into the gearbox.Gearbox functionsAudi drive select Audi drive select can be used to select between different vehicle configurations, i.e. modes. In this chapter you will learn how the gearbox control unit of the 0D6 gearbox responds to the various Audi drive select modes. Gearbox setups are tailored to the customer's requirements in a country-specific way. For this reason, only typical differences between the various modes can be shown here.18 Backlift / offroad mode (models with air suspension) In lift / offroad mode the gearbox control unit assists driving in rough terrain by providing adapted functions. Gear selection follows a fixed shift program without driver type recognition. Gears are held up to high revs, like in selector position S. Selector position S is not available but manual shifting is possible in tiptronic mode (manual mode M). Automatic upshifting of the gearbox is suppressed in tiptronic mode. The engine revs up to the rpm limit without shifting up. This prevents unwanted continuous up-and-down shifting. The suppression of automatic upshifting enables the engine to stop on a hill at full rpm. Even if traction is lost briefly, the gear is held to ensure that the full drive torque is available when the wheels regain full traction. The suppression of automatic upshifting allows the full braking effect of the engine to be utilised when travelling downhill. To protect the engine against overspeeding the gearbox shifts up before a defined engine speed is reached. When a speed of 30 kph is exceeded, the vehicle exits lift/offroad mode and switches to allroad mode. At the same time, the gearbox control unit selects the selector position which was active before lift / offroad mode was selected (D or S). auto modeForward Ξ ContentsDriver type recognition in selector positions D and S: In selector positions D and S driver type recognition is based on the driving style adopted by the driver. Criteria for driver type recognition include the mode of actuation of the brake and accelerator pedals, the speed of the vehicle as well as transverse and longitudinal acceleration of the vehicle within defined periods. Accordingly, an economical driving style leads to early upshifts and late downshifts. A sporty driving style is made possible by late upshifts and early downshifts. The driving phases in which the driver adopts an efficient, economical, sporty or manual driving style can be read out using the diagnostic tester. Speed D: Gearshifts are comfort-oriented and shift point selection is adapted to the driver's driving style with the assistance of driver type recognition. Selector position S1): In Sport mode (sport program), the shift points are sporty and adapted to the performance range of the engine. Shift points are configured with the assistance of driver type recognition. Shift times and shift points vary from driving in the standard sport program to a handling course setup with short, noticeable shift cycles.allroad mode The allroad mode does not have any effect on the gearbox setup.dynamic mode efficiency mode In efficiency mode the gearbox setup follows a defined shift program without driver type recognition. Upshifts are executed as early as possible and downshifts are performed late in order to conserve fuel and cut C02 emissions. In addition, the engine power output is reduced, allowing the gearbox control unit to reduce the clutch pressure. This, in turn, has a positive effect on fuel economy and CO2 emissions. In efficiency mode both the tiptronic function and selector position S are available. If selector position S is activated before the engine is shut off, the efficiency mode (E) is automatically activated when the engine is subsequently started1). If the driver wishes to have selector position S, he must select this. An E is displayed in the gear selection indicator as the selector position (E1 – 8). If dynamic mode is selected, the gearbox control unit activates the sport program (selector position S). In dynamic mode both the tiptronic functions and selector position D are available. If selector position D is activated before shutting off the engine, selector position (D) is again activated when the engine is subsequently started 1). If the driver wishes to have selector position S, he must select this.individual mode In individual mode the driver can freely select the gearbox setup irrespective of other vehicle systems.comfort mode The gearbox setup is especially comfort-oriented with soft gear shifts and low engine speeds. As is the case in auto mode, gear selection is aided by driver type recognition.Neutral idle control In the Audi SQ7 the gearbox is not disengaged at idle as described in SSP 632 on page 52.Other functions In addition to Audi drive select, the gearbox control unit employs a navigation-data-based shift strategy to increase comfort and efficiency. The coasting mode and the start-stop system provide higher efficiency; the downhill assist function improves comfort. All of these functions are identical to those of the 8-speed automatic gearbox 0D5 as described in SSP 632, page 51 ff.1) n accordance with the exhaust emissions certification, the drive programs of selector position D or E are always preselected when the I vehicle is restarted.Reference For a summary of the vehicle systems influenced by Audi drive select in the Audi Q7, refer to page 36 of this self study programme.19 BackForward Ξ Contentsquattro with sport differentialThe suspension control system "quattro mit sport differential" was first used on the Audi S4 (type 8K) in 2009. This first-generation system is described in detail in SSP 476 and is equipped with sport differential 0BF or 0BE depending on engine version. The Audi SQ7 (type 4M) employs a further development of the first-generation system. The second-generation system works with two control units which activate the rear axle drive of the 0BX sport differential. The suspension control unit J775 conditions input signals centrally and determines the operating state of the vehicle. On this basis and depending on the Audi drive select mode selected, the suspension control unit determines how much torque needs to be redistributed to the rear axle. The data for the required for the redistribution of torque is sent to the differential lock control unit via the FlexRay bus. The differential lock control unit J187 identifies the sport differential and the corresponding vehicle on the basis of internal data. It activates the hydraulics of the sport differential, which in turn redistributes the engine torque. The coefficient of friction of each clutch and the wear-dependent change in this value is compensated by adapted values stored in the control unit J187 An optimised control strategy is implemented within the content of this new architecture. As a result, the torque is redistributed even more precisely and before a tendency to understeer becomes noticeable. The hydraulic control unit of sport differential 0BX is identical to the first generation with regard to its sensors, actuators and clutch activation. However, it is not compatible with the first generation due to extensive detailed improvements. For example, the pressure sensors have been shortened by 13 mm due to space constraints. The inner workings including the torque overlay units and the clutches are also to a large exent identical to those of the first generation. Weight reduction measures and the new low-viscosity axle oil increase overall efficiency.Operating unit 1 for drive and comfort/ convenience functions E791Communication via FlexRayDifferential lock control unit J187651_043Suspension control unit J775 Rear axle drive 0BX – sport differential651_044Torque redistributionThe suspension control system "quattro with sport differential" redistributes up to 1200 Nm of torque (differential torque) between the rear wheels to provide agile and neutral handling. Redistribution of torque also improves driving stability in oversteer situations without loss of driving dynamics and avoids understeer when accelerating out of curves.Steering into a curve Torque is redistributed to the rear wheel on the outside of the curve to improve cornering651_045 20Straight ahead Torque is redistributed evenlyAccelerating out of a curve Torque is redistributed to the rear wheel on the outside of the curve to avoid understeer caused by acceleration.651_046 651_047 BackForward Ξ ContentsProtective function and diagnosticsTo safeguard against excessively high temperatures, less torque is redistributed under extreme load. If the load situation is such that no torque is redistributed, this is indicated to the driver via a message displayed on the instrument cluster. If a fault is diagnosed, no corrective adjustments are made or no torque is redistributed and, likewise, a message is displayed on the instrument cluster. The differential lock control unit J187 can be addressed via the diagnostic tester by entering address code 32. The diagnostic results can be obtained via "rear axle drive 0BX - sport differential". For more information about the diagnostic options for the sport differential, refer to page 25.Engraved classification of the multiplate clutches (for more information about clutch classification, refer to page 14 of SSP 476).Oil pressure and temperature sensor G437 (brown)Oil pressure and temperature sensor 2 G640 (black) Clutch valve 2 for all-wheel-drive system (right/brown) Engraved engine code and date of manufacture Pump for all-wheel-drive system V415 Four-wheel drive clutch valve N445 (left/black)Audi drive selectThe range of options provided by Audi drive select has been extended compared to the first generation of sport differentials. The driver can choose between the ift / offroad, efficiency, comfort, auto, allroad, dynamic and individual modes. Depending on what Audi drive select mode is selected, the suspension control system "quattro with sport differential" is assigned to651_048one of the following 3 setups: comfort, auto or dynamic. In the individual mode of Audi drive select, the driver can freely select the comfort, auto or dynamic setup for the suspension control system "quattro mit sport differential", irrespective of the other systems integrated into Audi drive select.Audi drive select Modi lift / offroad efficiency comfort auto allroad dynamic individualSetup Sport differential comfort comfort comfort auto auto dynamic1) comfort auto dynamic1)comfort The suspension control system "quattro with sport differential" has a moderate setup. No adjustments are made to sharpen steering response at higher speeds. Compared directly to the other setups, this setup highlights the effect of the system within the vehicle. auto The suspension control system "quattro with sport differential" has a balanced setup. The adjustments made to sharpen steering response at higher speeds provide neutral handling. The vehicle is stabilised in the event of oversteer. dynamic The suspension control system "quattro with sport differential" has a sporty setup. The redistribution of torque provides very agile handling. Only in the event of pronounced oversteer is the torque redistributed to stabilise the vehicle.1) f the vehicle is towing a trailer, the auto setup is set within the I system when the sport differential setup dynamic is selected.Reference For a summary of the vehicle systems influenced by Audi drive select in the Audi Q7, refer to page 36 of this self study programme.21 BackForward Ξ ContentsOil systemsAs with the first-generation differential, the rear axle drive 0BX sport differential has an MTF system and an ATF system. It is important not to mix up these systems when changing the oil. Pay attention to the respective assignments of the filling, inspection and drain screws.ATF breatherATF breatherMTF breatherATF filler and inspection screw651_049MTF drain screwMTF filler and inspection screwATF drain screwOil leakage bore, left side Oil leakage bore, right side651_050 22 BackForward Ξ ContentsCutaway viewThe interior workings of sport differential 0BX are identical to those of the first generation, i.e. sport differentials 0BF and 0BE.Crown wheel welded onto the differential case Flange shaft - prop shaft Double shaft oil seal with oil drainage port Right flange shaftFront rubber-metal bearingMTF breatherSuperposition gearbox, rightSuperposition gearbox, leftLeft flange shaftMulti-plate clutchHydraulic pumpClutch pistonHydraulic pipeMotor for hydraulic pump V401Shaft oil sealDouble shaft oil seal with oil drainage port651_051Note For more information about the technology and working principle of sport differential 0BX, which is largely identical to the technology and working principle of the 0BF and 0BE sport differentials, refer to SSP 476 and the following Service TV programmes: • • • • STV_0105_Audi quattro with sport differential 0BF Part 1 STV_0106_Audi quattro with sport differential 0BF Part 2 STV_0120_Audi quattro with sport differential 0BF Part 3 STV_0122_Audi quattro with sport differential 0BF Part 423 BackForward Ξ ContentsServiceUsing the diagnostic tester The diagnostic functions assigned to address codes 02 Gearbox electronics, 32 Lock electronics, 81 Selector lever and 01 Engine electronics are available for power transmission in the Audi SQ7 using the diagnostic tester. Address code 02 Gearbox electronics The automatic gearbox control unit is addressed via address code 02 Gearbox electronics, and the diagnostic results can be obtained via "0D6 gearbox". In addition, the listed diagnostic functions can be used for assessment and handling of the 0D6 gearbox. Adaptation The following functions can be activated or deactivated using the adaption function. • Individual gear display The gear display for selector lever positions D and S can be activated or deactivated separately in the instrument cluster by adapting the individual selector lever position display. The gear indicator is always active in manual mode M (tiptronic mode). • Route data Navigation data based gear selection can be activated or deactivated using this function. Refer to SSP 632, page 51. • Automatic upshift When the automatic upshift function is activated, the gearbox shifts to the next higher gear before the engine speed limiter cuts in. If the automatic upshift function is deactivated, the engine runs up to the speed limit without shifting up. • Neutral idle control Navigation based gear selection can be activated or deactivated using this adaption function (refer to page 52). The neutral idle control function is not available in the Audi SQ7. • Tiptronic switch This adaption function can be used to activate or deactivate tip shifting in D. Actuator test The following actuator tests are offered: • Selector lever lock N110 Actuator diagnostics cannot be performed under address code 02. The selector lever solenoid can be checked via address code 81 – Selector lever. • Open converter lockup clutch With this function, the converter lockup clutch stays open while driving from a standing start. The converter lockup clutch is not controlled. This function is used to selectively isolate unwanted rotary vibration in the internal combustion engine from the driveline for fault-finding purposes. • Coolant shut-off valve N509 This actuator test was unavailable at the time of preparation of the self study programme. • Auxiliary hydraulic pump for gear oil V475 This actuator test is not applicable to the 0D6 gearbox, which has no auxiliary hydraulic pump V475.Address code 01 Engine electronics The engine control unit J623 can be addressed via address code 01 - Engine electronics. The following diagnostic functions relevant to power transmission can be carried out: • Gearbox mounting valve 1 N262 Actuator diagnostics: R/H gearbox mounting valve. • Gearbox mounting valve 2 N263 Actuator diagnostics: L/H gearbox mounting valve • Coolant circuit ventilation routine The high-temperature circuit of the internal combustion engine can be vented using this guided function. The ATF cooling system is integrated into this circuit.Basic setting The following adaption processes can be performed using the basic setting function. • Quick adaption when the vehicle is stationary, e.g. after changing the ATF, replacing the brakes/clutches or the mechatronics module. • Rest all programmed values The adaption values of the clutches can be read and reset collectively. It is not possible to reset individual adaption values.24 BackAddress code 32 Lock electronics The differential lock control unit J187 is addressed via address code 32, and the diagnostic results can be obtained via "rear axle drive 0BX – sport differential". In addition, the listed diagnostic functions can be used for assessment and handling of the sport differential. Identification The control unit identification and the event memory can be read out using this function. SVM control unit configuration This function checks whether the control unit has been configured correctly for the vehicle (software version, coding). Replace control unit First of all, the adaption values of the old control unit are read out and buffered via the diagnostic tester. After the new control unit has been installed, it is configured using these adaption values. If the old control unit cannot be addressed, the clutch classification must be entered manually for the new control unit. In addition, the software and the coding of the control unit are checked via the SVM system. If the axle drive is used, the ATF must be replaced. Adapting the oil pressure and temperature sensors This function allows for identification of the sport differential by the control unit via the oil pressure and temperature sensors. Replenish ATF (hydraulics) This function resets the oil deterioration values and aids filling the ATF (including lines, for example). This function may only be carried out in connection with an oil change. Torque redistribution This function can be used to check for torque redistribution, installation on the correct side and proper functioning of the clutch valves. Test clutch function The control unit require that the clutches of the sport differential develop a fixed holding torque which prevents the shafts from spinning. The holding torque can be checked using a torque wrench. Replacing the rear axle drive The contl unit J187 identifies the sport differential based on the information from oil pressure and oil temperature sensors G427 and G640. The axle drive/control unit is assigned when the clutch classification is entered see SSP 476. Actuator test The following actuator tests are offered: • System function testing, pressure build-up at both clutches • Venting the hydraulics (maximum pressure build-up) • Checking the left-hand clutch, see "Clutch function testing"1) • Checking the right-hand clutch, see "Clutch function testing"1) Address code 81 Selector leverForward Ξ ContentsThe selector lever sensors control unit J587 can be addressed via address code 81 - Selector lever. The diagnostic functions of the selector mechanism can be used. The selector mechanism of the Audi SQ7 is identical to the basic version as described in SSP 632, page 40 ff. An actuator test is available for the following components of the selector mechanism: • Selector lever position display Y5 • Selector lever lock solenoid N110 • Transverse selector lever lock motor V577Towing If a vehicle with an 0B6 gearbox needs towing, the usual restrictions on automatic gearboxes apply: • • • • Emergency release the parking lock (refer to SSP 632, page 48). Max. towing speed is 50 kph. Max. towing distance 50 km. Do not tow the vehicle with the front or rear axle raised off the ground.Reason When the engine is at standstill, the oil pump is not driven and certain parts of the gearbox are not lubricated. Failure to comply with the towing conditions can lead to serious gearbox damage.Note Note the other descriptions and notes on the topic of tow-starting and towing in the owner's manual.Indicator lamps If the red gearbox warning lamp appears in the instrument cluster, the driver will be advised against driving the vehicle any further. If one of the yellow warning lamps for the gearbox or the suspension control system "quattro with sport differenmtial" appears in the instrument cluster, it is normally possible to continue driving the vehicle. Driver information is displayed informing the driver what to do.Note For more detailed information about the Guided Fault Finding for the sport differential, refer to SSP 476 page 42 ff.For detailed and up-to-date information, please refer to the vehicle owner's manual.1)This actuator test is identical to the guided function "Check clutch" for the left-hand or right-hand clutch. 25 BackForward Ξ ContentsSuspensionOverviewThe suspension components and systems of the Audi SQ7 are carry-overs from the Audi Q7. They have been adapted to the specific requirements of the Audi SQ7, where required. In terms of their design, function, operation and scope of service, these components and systems are identical to those of the Audi Q7 (type 4M). A sports suspension with air springs and controlled damping (adaptive air suspension sport, 2MA) is offered for the Audi SQ7 as standard. The electromechanical active roll stabilisation system is being used by Audi for the first time in the SQ7.651_09226 BackForward Ξ ContentsDriving dynamics – rollThe term driving dynamics describes the movement of the vehicle taking into account the forces acting on the vehicle. One such type of movement is roll. This is the rotational movement of the vehicle about its longitudinal axis (roll axis). The orientation of the roll axis is defined by the structural design of the axles. When cornering, roll occurs due to centrifugal force acting on the vehicle's centre of mass. The distance between the centre of mass and the roll axis is the roll torque lever arm. The centrifugal force acting towards the outside of the curve causes the vehicle body to roll towards the outside of the curve. In the process the weight of the vehicle shifts towards the wheels on the outside of the curve, reducing the weight on the wheels on the inside of the curve. A similar effect occurs when the vehicle body is exposed to side winds. The wheel contact forces which change due to the action of centrifugal force can be detrimental to driving stability. Conversely, controlled roll behaviour can have certain beneficial effects. Roll reduction is important not only for dynamic stability, but also for driving comfort.S R X FCentre of mass Roll axis Roll torque lever arm Centrifugal forceFSX R651_093Use of anti-roll barsIn the vehicle, the main task of the front and rear axle anti-roll bars is to limit rolling movement in interaction with the springs and dampers. Anti-roll bars connect the relevant axle components (links, swivel bearings and wheel bearings) on both sides of the corresponding axle. They are designed as torsionally soft components. This means that they deform when different forces are placed simultaneously on their outer attachment points. This allows relative movement of the axle components connected by the anti-roll bar. The wheels of the axle have a limited range of compression and rebound travel despite being connected by the anti-roll bar. A drawback of this configuration is that one-sided excitation at a wheel is transmitted to the other wheel of the axle by the effect of the anti-roll bar. This process is known as "roll copying". Usually solid bars or tubes are used as anti-roll bars.651_09427 BackAnti-roll bars and their characteristics The design of anti-roll bars is always a compromise. The required dynamic characteristics of the suspension dictate whether less torsional rigidity (comfortable suspension setup) or more torsional rigidity (sporty suspension setup) is needed. To achieve a sporty setup, the springs have to be accordingly "firmer" and the dampers have to produce higher damping forces. A setup such as this allows a dynamic style of driving, but results in less comfort for the passengers. Conversely, a vehicle with a comfort-oriented setup will reach its dynamic limits earlier, leading to loss of driving dynamics and agility. It is virtually impossible to resolve this conflict of interests using conventional suspension technology. Moreover, the front and rear axle anti-roll bars cannot be treated separately when they are designed. The self-steering behaviour of the vehicle is to a large extent influenced by the stiffness relationship between the front and rear axle anti-roll bars.Forward Ξ ContentsDynamics ComfortAnti-roll bar torsional rigidity651_095Compared with: Roll behaviour of race cars When it comes to race cars, hardly any attention is given to comfort. In return, they achieve impressive driving dynamics. Suspension travel is minimal compared to "normal" road-going vehicles and roll is virtually eliminated.651_10228 BackForward Ξ ContentsRoll stabilisation – basic principleThe well-known drawbacks of the conventional anti-roll bar do not apply if the torsional rigidity of the anti-roll bar can be adapted to the driving situation. In fact, there are even some advantages. For example, it is possible to improve traction by isolating the sides of each axle in offroad mode through increased axle articulation. As conventional anti-roll bars have a defined and non-variable degree of torsional rigidity, additional design measures are necessary in order to achieve this goal. The basic principle involves dividing the conventional anti-roll bar into 2 "halves" and "countertensioning" these halves by means of a special mechanism. The axle components themelves can be adopted unchanged without any need for modification of the anti-roll bar connections. Generally speaking, such a "tensioning mechanism" (actuator) can be driven hydraulically or electrically. A hydraulic drive offers installation space advantages when it comes to actuators due to its higher power density but suffers from major drawbacks when compared to an electric drive. The hydraulic drive requires an additional hydraulic pump and additional lines, resulting in added installation work during production and extra maintenance during operation. A hydraulic drive has a higher total energy demand because on-demand activation is not possible. Electromechanical systems additionally offer the option of recuperation, which helps to further reduce energy demand. There is also the possibility of environmental contamination as a result of leakages within the system. For this reason, an electrical actuator drive was developed for use in the Audi SQ7. The best results in regard to driving comfort, roll behaviour, driving stability and offroad functionality are achieved through a combination of roll stabilisation and air suspension in conjunction with controlled damping.Actuator for increasing the tension between each side of the anti-roll bar. The higher the tension, the higher the torsional rigidity.651_104651_092651_096 29 BackForward Ξ ContentsSystem componentsElectrically/electronically controlled anti-roll bars are used on the front and rear axles of the Audi SQ7. Each actuator is regulated by a separate control unit. Both control units work in conjunction with the suspension control unit. They communicate with one another and with the suspension control unit via the high-speed SUB CAN. The control units has a logic module which runs on 12-volt onboard voltage. The power supply responsible for activating the actuator is integrated into the 48-volt electrical system.651_097Installation locations in the vehicleRear suspension stabilisation actuator V636 Roll stabilisation control unit J924 Roll stabilisation control unit 2 J1096Front suspension stabilisation actuator V634Suspension control unit J775651_098Reference For more information about the 48-volt electrical system, refer to the chapter on "Electrics and electronics" in this self study programme.30 BackForward Ξ ContentsAxle componentsRear axle with roll stabilisationRoll stabilisation control unit 2 J1096Rear suspension stabilisation actuator V636651_088Front axle with roll stabilisationRoll stabilisation control unit J924"Anti-roll bar half" permanently connected to the actuator Front suspension stabilisation actuator V634 "Anti-roll bar half" bolted to the actuator – non-detachable connection!651_08931 BackForward Ξ ContentsDesign of the actuatorsA permanently excited synchronous three-phase AC motor with a downstream 3-step planetary gear is used as an active actuator in the Audi SQ7. Peak torque is about 1200 Nm and maximum torsion angle speed is 120° per second. An electrical power output of about 1.5 kW is required for this purpose. The electric motor is activated by applying a voltage of 48 V through the control unit power supply. The planetary gear has a total ratio of about 1 : 200.651_101Anti-roll bar (bolted to actuator)Planetary gearElectric motorAnti-roll bar (permanently connected to actuator)651_097 32 BackForward Ξ ContentsFunctional principleWhen the electric motor is activated by the corresponding control unit, the rotor applies a torque to the planetary gear input shaft. The high total ratio of the planetary gear (1 : 200) multiplies the torque (up to 1200 Nm), which is available at the gearbox output shaft and acts on the anti-roll bar half to which it is connected. The electric motor stator being connected to the other anti-roll bar half, both anti-roll bar halves are "tensioned" relative to one another, generating more torsional torque (making the anti-roll bar "firmer", as it were). Depending on requirements, the anti-roll bar halves can be tensioned by applying any amount of torque up to the maximum level. To improve traction under offroad conditions in particular, the anti-roll bar halves can even be decoupled by not activating the electric motor (through active wheel excitation adjustment). In this scenario, the wheels do not lose contact with the ground despite the large axle articulation and a drive torque can be generated at both wheels.651_09033 BackForward Ξ ContentsFunctional principleThe suspension control unit uses the steering angle and the speed of the vehicle to predict how much transverse acceleration will occur. This prediction is important because the measured value for actual transverse acceleration is determined too late to be effective as a basic control variable. The control unit uses the measured value for actual transverse acceleration and its prediction to calculate a transverse acceleration valve which serves as the calculation basis for the roll stabilisation control units. This transverse acceleration value and the measured yaw rate provide the basis for calculating the distribution of roll torque to the front and rear axles, which the suspension control unit sends to both roll stabilisation control units. The roll stabilisation control units calculate the required total amount of roll torque on the basis of the transverse acceleration values received. For redundancy reasons, both control units carry out the same calculation routines. This roll torque in relation to the roll torque distribution factor sent by the suspension control unit is distributed proportionally to the front and rear axles. Comfort aspects are factored into the control process by additionally making allowance for the vehicle ride heights. If, for example, road surface excitation is detected on one side of the vehicle, the roll torque is reduced accordingly at this axle. The "softer" anti-roll bar setup reduces roll copying on the opposite side of the vehicle, thereby increasing ride comfort.ABS control unit J104Roll stabilisation control unit J924 Suspension control unit J775 Lateral acceleration Distribution factor Vehicle levelActivation Anti-roll bar Front axleRoll stabilisation control unit 2 J1096 Vehicle ride heightsActivation Anti-roll bar Rear axleVehicle level sender, G76 – 289651_091RegulatedThe distribution of overall roll torque to the front and rear axles has a special roll to play in the control process. Whether the vehicle understeers or oversteers when cornerning depends to a high degree on the "firmness" of the anti-roll bars. If, for instance, the wheel on the outside of the curve compresses due to an increase in wheel load (caused by the centrifugal force acting on the wheel), this compression movement will be transmitted partially to the wheel on the inside of the curve. The wheel load acting on the wheel on the inside of the curve will decrease as a result. The greater the roll torque (i.e. the "firmer" the anti-roll bar), the greater the differences in wheel load between the wheels of an axle. Less lateral force is transmitted through the wheels of this axle due to the non-linear tyre characteristic (skew angle vs. wheel contact force). In other words: to transmit the same amount of lateral force, a higher skew angle of the tyres is required on the outside of the curve. If the anti-roll var on the front axle becomes "firmer", the self-steering behaviour of the vehicle shifts towards understeer when cornering. A "firmer" anti-roll bar on the rear axle produces oversteer. Given the possibility for varying the roll torques at the front and rear axles, the self-steering behaviour of the vehicle be adjusted from "understeer" through "neutral" to "oversteer" as the situation requires.651_099651_100The vehicle understeers – the vehicle pushes the front wheels towards the outside of the curve.34The vehicle oversteers – the rear end of the vehicle leaves its trajectory and pushes towards the outside of the curve. BackForward Ξ ContentsControl strategyDuring the control process, a distinction must be made between two key aspects: • the limitation on roll angle and the distribution of roll torque to the front and rear axles. During active vehicle operation, transverse acceleration occurs within a range of approximately 1 – 3 degrees per g (9.81 m/s2) when cornering. The Audi drive select setting chosen by the driver dictates whether the system allows lesser or greater roll angles. The greatest roll angles are allowed in comfort mode, while the least roll angles are allowed in dynamic mode. If the drive selects the auto or offroad mode, medium roll angles are obtained. • The distribution of roll torquer to the axles is also defined by the Drive select setting. In dynamic mode, the anti-roll bar on the rear axle has a "firmer" setup than in the other modes to give more neutral handling. In the other modes, a tendency to understeer is achieved by selecting a "firmer" setup for the front axle anti-roll bar. Active control processes take place upwards of a vehicle speed of about 5 kph. If the anti-roll bar control system fails, the overall system is switched off. If the signal from a vehicle level sensor or the transverse acceleration value is unavailable, the engines are activated in such a way that they maintain a constant actuator angle. Thsis corresponds to the behaviour of a passive, non-controlled anti-roll bar.Operation and driver informationThe system is active when the ignition is turned on and cannot be switched off by the driver. The driver operates the system by selecting the relevant Drive Select Mode. If the system is intact, the driver receives no information. In the event of a fault, a warning is issued via the dash panel centre display. Roll stabilisation: Malfunction! Driving stability limited! See handbook.651_103Service operationsThe roll stabilisation system has self-diagnostic capability and the front and rear axle regions are differentiated as follows: • Diagnostic code D4 = electromechanical active roll stabilisation 1 (front axle) • Diagnostic code D5 = electromechanical active roll stabilisation 2 (rear axle) The front and rear anti-roll bars are replaced as a complete unit by service centres. When removing an anti-roll bar, care must be taken to ensure that the connector for connecting the electrical wiring loom is not disconnected from the actuator. For functional reasons (leak tightness), the connector may only be installed once. After a control unit is replaced, it is encoded online. Before the new control unit is activated, a roll test is performed as part of the basic setting procedure. For this purpose, the vehicle must be standing on its wheels. A check is made automatically to determine whether the requirements for the test have been met or not, and the boundary conditions are indicated to the mechanic in the form of a table. The actual roll test is performed by the control units, which actively activate the anti-roll bars, causing the vehicle body to move. Note: When the test is carried out, the special requirements set out in the Workshop Manual must be observed. This basic setting is also suitable for carrying out a general function test on the system.35 BackForward Ξ ContentsElectrics and electronicsAudi drive selectFunctional characteristicsThe Audi SQ7 is equipped with the Audi drive select system. With Audi drive select, it is possible to modify the vehicle characteristic. The mode can be changed when the car is stationary or while driving. Condition: "Terminal 15 on". In any case, steering assistance, the gearbox control unit and the engine characteristic are affected. In addition, the system affects the following equipment: (The highlighted systems are those now featured on the SQ7 but not on the Q7 (type 4M).) • • • • • • • • • • • • • • • • Air conditioning system Cornering light Ambient interior lighting Fuel range display Interior sound Exterior sound Exhaust flap Rear axle steering Damper control Air suspension quattro with sport differential Cruise control system ACC Audi pre sense basic / pre sense city Start-stop system Electromechanical active roll stabilisationIn the Audi SQ7 the driver can select between the following drive modes: • lift / offroad • efficiency (not available for North American market) • comfort • auto • allroad • dynamic • individualSystem quattro with sport differentialVehicle characteristic As an integral part of the all-wheel drive, the suspension control system "quattro with sport differential" situatively distributes drive power to the rear axle. Depending