TECHNICAL DOCUMENTATION
SSP 653 Audi R8 Spyder

This PDF is currently unavailable.
Read document text
Audi R8 Spyder(Type 4S)Self Study Programme 653For internal use onlyAudi Service Training BackThe new open-top high-performance sports-car continues the Audi R8 success story. It began in 2007 with the market launch of the Audi R8 Coupé (Type 42), which was followed by the Audi R8 Spyder (Type 42) in 2010. Almost 27,000 units have now been sold of both variants. They demonstrate the high-tech skills of Audi and the brand's close association with motor sport. The new Audi R8 Spyder (Type 4S) reveals its dynamic character from the very first glimpse. The forward-shifted passenger compartment, the conspicuously accented wheel arches and the long tail lend it the classic proportions of a mid-engine sports-car. Compared with its predecessor, the new Audi R8 Spyder is 14 mm shorter with an overall length of 4,426 mm. Widthways it has expanded by 36 mm to 1,940 mm. The overall height of 1,244 mm is the same as the 1st-generation Audi R8 Spyder, as is the wheelbase of 2,650 mm. The road and wind noise perceptible to occupants is now substantially less than in the previous model. And the air turbulence at head height when the top is down has also been reduced.Forwards Ξ ContentsFor even greater comfort, there is a wind deflector made of synthetic fabric. It reduces the back-flow in the head area by around 90% and in the shoulder/neck area by 80%. In addition to the fabric wind deflector, the rear window can also be used as a wind deflector when the top is down. With the window lowered on the other hand, occupants can fully appreciate the characteristic throaty roar of the V10 power unit. The Audi R8 Spyder (Type 4S) is almost entirely hand-crafted at a specially constructed production facility near to Neckarsulm called "Audi Böllinger Höfe". The site represents and expansion of the quattro GmbH small series capabilities. The manufacturing character of the production facility offers extensive scope for satisfying specific customer wishes. The bodywork attachments such as front spoiler and diffuser can be individually specified, as can the distinctive side blades – with the option of high-gloss carbon fibre, for instance.653_002 2ContentsIntroductionIntroduction __________________________________________________________________________________________________________________________________________________ 4 Dimensions ___________________________________________________________________________________________________________________________________________________ 6BodyIntroduction __________________________________________________________________________________________________________________________________________________ 8Soft-topIntroduction _________________________________________________________________________________________________________________________________________________ 12 Components _________________________________________________________________________________________________________________________________________________ 13Soft-top control systemSoft-top drive unit _ _________________________________________________________________________________________________________________________________________ 16 Overview _____________________________________________________________________________________________________________________________________________________ 20 Soft-top operation and display indications _______________________________________________________________________________________________________________ 22 Functional sequence when raising and lowering the soft-top __________________________________________________________________________________________ 28 Components of the soft-top control system _ ____________________________________________________________________________________________________________ 35 Rear window _________________________________________________________________________________________________________________________________________________ 55Powertrain units5.2l V10 FSI engine _________________________________________________________________________________________________________________________________________ 60Power transmissionOverview _____________________________________________________________________________________________________________________________________________________ 62SuspensionOverview _____________________________________________________________________________________________________________________________________________________ 64Electrics and electronicsTopology _____________________________________________________________________________________________________________________________________________________ 66 Rear window module _______________________________________________________________________________________________________________________________________ 69Air conditioningOverview _____________________________________________________________________________________________________________________________________________________ 70Safety and driver assistance systemsPassive safety ________________________________________________________________________________________________________________________________________________ 72 Assistance systems _________________________________________________________________________________________________________________________________________ 76Infotainment and Audi connectOverview of versions ________________________________________________________________________________________________________________________________________ 78 Sound systems ______________________________________________________________________________________________________________________________________________ 79 Aerials overview _____________________________________________________________________________________________________________________________________________ 82Inspection and maintenanceOverview _____________________________________________________________________________________________________________________________________________________ 84AppendixSelf study programmes _ ____________________________________________________________________________________________________________________________________ 86The self study programme teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a repair manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. This content is not updated. For further information about maintenance and repair work, always refer to the current technical literature.NoteReference3 BackForwards Ξ ContentsIntroductionIntroductionHorizontal lines on the front and rear ends emphasis the width of the Audi R8 Spyder (Type 4S) as does the broad and low-profile Audi Singleframe with its honeycomb pattern radiator grille. Plastically moulded surfaces connect it to the wedge-shaped headlights in which 37 LEDs provide ultra-bright illumination as standard.Engine10-cylinder V-configuration engine with a capacity of 5.2 l, maximum power output of 397 kW, start/stop system and cylinder on demand.Air conditioningLike its predecessor, the new Audi R8 (Type 4S) is equipped with a singlezone automatic air conditioning system. The 3 central controls for the air conditioning system are in the form of rotary push-buttons. The centre rotary push-button has a display which can be used to set the cabin temperature.BodyAs with the Audi R8 Coupé (Type 4S), the Audi R8 Spyder Audi Space Frame (ASF) body is distinguished by its multi-material lightweight design. It combines components made of aluminium and structurally integral carbonfibre-reinforced plastic (CFRP) with one another. The aluminium components make up 79.6% of the multi-material ASF. They form a framework which the Audi engineers have reinforced specifically in the area of the sills, A-pillars and windscreen frame compared with the Audi R8 Coupé. The torsional rigidity in comparison with the Audi R8 Spyder (Type 42) has been increased by 50%.4Power transmissionDrive is provided by the 0BZ 7-speed dual clutch gearbox together with mechanical limited slip differential for the rear axle and the 0D4 front final drive together with a newly developed electro-hydraulic all-wheel drive clutch. The dual clutch gearbox receives shift commands electronically (shiftby-wire). A variety of gearbox set-ups can be selected on the Audi drive select handling system. A launch control system allows full-throttle acceleration from a standing start. BackForwards Ξ ContentsDisplays and operationThe Audi R8 Spyder (Type 4S) has a large 12.3 inch fully digital Audi virtual cockpit instrument cluster with dynamic animations and graphics. The START-ENGINE-STOP and Audi drive select buttons are located on the multifunction steering wheel. The optional Performance steering wheel features 2 extra satellite buttons – one for performance mode together with a thumb-wheel for selecting the driving programs and the other for controlling the sports exhaust system. MMI Navigation plus with MMI touch is a standard feature. It is controlled via the steering wheel, the MMI terminal on the centre console or natural voice control – conveniently registered by 3 small microphones in the seat belts.SuspensionThe suspension features lightweight aluminium wishbones for all 4 wheels. With the Audi drive select dynamic handling system, the driver has the choice of 4 modes (comfort, auto, dynamic and individual) to control the way in which important technical components operate. As standard, the system incorporates the engine characteristics, steering, S tronic transmission, control of the exhaust flaps and quattro drive system as well as optional extras such as Audi magnetic ride and dynamic steering. For the first time on the Audi R8 Spyder, the Performance leather steering wheel is available as an option. It includes the 3 additional driving programs dry, wet and snow. With their pre-programmed frictional coefficient parameters, they enable the driver to adapt the vehicle to the particular road conditions. As well as the modules referred to, those modes also affect the ESC stability control.Assistance systemsThe following systems are available as options: • Park Assist Plus • Rear-view camera653_009Convertible topThe soft-top of the Audi R8 Spyder (Type 4S) is a new but typically Audi fabric design. An electro-hydraulic drive system raises and lowers the softtop at the press of a button in only 20s, even when the car is moving at up to 50 kph. Covering the slim stowage compartment into which the soft-top folds away when lowered is the soft-top compartment cover. Two fins extending to the rear tension the soft-top and lend the Audi R8 Spyder a dynamic profile.HeadlightsThe headlights feature LED technology as standard. The Audi R8 Spyder also offers the option of a laser spot for the main beam and the front dynamic turn signals. The LED headlights with Audi Laserlight are identifiable by a blue anodised strip – which is also illuminated – in the headlight. The laser main beam has a range of up to 600 m – almost double the range of the LED main beam. Dynamic turn signals are standard in the rear lights.5 BackForwards Ξ ContentsDimensions1638 1940653_00312441599 2037653_0049942650 4426977 1)782653_0056 BackForwards Ξ Contents15022)14003)653_006Exterior dimensions and weightsLength in mm Width (not including exterior mirrors) in mm Width (including exterior mirrors) in mm Height in mm Front track width in mm Rear track width in mm Wheelbase in mm Kerb weight in kg Gross vehicle weight in kg 4426 1940 2037 1244 1638 1599 2650 1720 2020Inner dimensions and other specificationsFront cabin width in mm Front shoulder width in mm Luggage compartment capacity in l Drag coefficient cw Capacity of fuel tank in l 15022) 14003) 112 0,36 83Maximum headroom Elbow room width 3) Shoulder room width1) 2)All dimensions are given in millimetres and refer to the unladen weight of the vehicle.7 BackForwards Ξ ContentsBodyIntroductionThe new Audi R8 Spyder is based on the Modular Sportscar System (MSS) sports-car platform. Courtesy of the Audi lightweight design, the multi-material ASF is distinguished by highly rigid bodywork combined with minimal mass. As on the Audi R8 Coupé, the body combines cast and extruded aluminium components with structurally integral carbon-fibrereinforced plastic parts. The aluminium components make up 79.6 % of the multi-material ASF. They form a framework which has been reinforced specifically in the area of the sills, A-pillars and windscreen frame compared with the Audi R8 Coupé. The multi-material ASF of the new Audi R8 Spyder has a total weight of only 208 kg, while its torsional rigidity has increased by 50% compared with the previous model.Key:Sheet aluminium Die-cast aluminium Aluminium profile Carbon fibre reinforced polymer (CFRP)Reference Information on bodywork joining techniques and manufacture can be found in Self-Study Programme 641 "Audi R8 (Type 4S)".8 BackForwards Ξ ContentsWindscreen frame conceptOne example of lightweight structural design is the windscreen frame. On open-top vehicles, it is a part of the body that has very demanding requirements in terms of strength and rigidity. In the case of the Audi R8 Spyder, those demands are met by using an all-aluminium construction and by detailed matching of wall thickness and profile cross-section without the use of tubular steel. The upper casting incorporates mounts for the soft-top locking mechanism, wiring and seals. And because of the strict dimensional stability requirements it has to satisfy, it also contributes to the flawless functioning of the soft-top raising and lowering mechanism.Crash design features of the body (load transfer paths)On account of the mid-engine concept, very specific requirements apply to the crash design. During a frontal collision, for example, the complete mass of the drive line must be absorbed by the structure for the full duration of the collision. To achieve that, the forces which occur during a frontal impact are transferred to the other parts of the vehicle structure via 3 load paths. To dissipate the impact energy, the side members should deform in a controlled manner and transmit the residual energy to the next component as effectively as possible.653_098When repairing such a complex body, it is important to keep these defined deformation zones intact and not to disrupt the transfer of forces. To guarantee that this is the case after repair work is completed, the repair depths and repair methods are defined in precise detail and described in the current ELSA service literature.653_1119 BackForwards Ξ ContentsSill bodywork reinforcementThe door sills made from extruded aluminium sections make a substantial contribution to the increased rigidity. Due to the absence of a roof structure, it is necessary for the door sills of the Audi R8 Spyder to be thicker and to be integrated into the structure by means of node castings. Because of the complex geometry, partial replacement of these components is not possible. If they are damaged, the entire sill has to be replaced.653_112Audi R8 Spyder sillAudi R8 Coupé sillUltra-RTM (resin transfer moulding)At present, the carbon-fibre-reinforced plastic (CFRP/carbon fibre) parts of the Audi R8 Coupé body are made up of multiple individual, non-integral components which are subsequently joined together to form a module. On the Audi R8 Spyder, the new sandwich/integral construction method has made it possible not only to reduce the number of components but also to save on joining systems. Thus the integral rear bulkhead sandwich structure improves torsional rigidity, while Key:Aluminium HD RTM carbon-fibre-reinforced plastic Ultra-RTM carbon-fibre-reinforced sandwich structurethe integral B-pillars help optimise crash performance. Those two features alone have made it possible to combine 10 previously separate components into 3 sandwich structures with integral load transfer points, thereby dispensing with additional bonding flanges. For reasons of cost, this design method is normally only used in motor racing or in supercars (carbon-fibre monocoques) but can now also be employed economically in volume production.653_09610 BackForwards Ξ ContentsNon-destructive inspection (NDI)After an accident, components can be non-destructively inspected at a service centre by ultrasound measurement The test probe transmits ultrasonic pulses which have a very short duration (1 to 10 μs) and pass through the component under inspection. The sound is reflected by the rear wall of the part being examined and is picked up by the test probe as an echo. Based on the time between signal transmission and receipt of the echo, and the pre-set parameters, a software program calculates the depth and position at which the sound is reflected.ProbeComponent thickness653_097 653_095CFRP componentDefect in componentReference Further information about the non-destructive inspection of CFRP components can be found in Self-Study Programme 641 "Audi R8 (Type 4S)", in the current service literature in ELSA and on the Audi ServiceNet.Outer skinLightweight construction and design flexibility were the top priorities when it came to selecting the outer skin materials. To Key:Aluminium PU/Thermoplastic GFRP = Glass-fibre-reinforced plastic CFRP = Carbon-fibre-reinforced plasticmeet the targets for quality, function and cost, the best-suited material was selected for each component.653_11311 BackForwards Ξ ContentsSoft-topIntroductionAs already seen on the previous generation, the new Audi R8 Spyder also features a lightweight fabric soft-top that tapers into 2 fins at the back. Those fins tension the fabric and, like the large soft-top compartment cover, harmonise perfectly with the athletic styling of the Audi R8 Spyder. The soft-top module is located behind the seats. It consists of the components roll-over protection system, soft-top, soft-top well and rear window compartment. The multi-joint hinge for the soft-top compartment cover, which is made of CFRP, is also part of the soft-top module.653_099If the soft-top module has to be removed in the course of maintenance or repairs, it is essential to follow the correct tightening sequence for the bolts that fix the soft-top module to the rear bulkhead. If the correct sequence is not followed, malfunctions when raising and lowering the soft-top may result.Correct alignment of the soft-top module is achieved by means of compensators in the roll hoop mounting which have to be set flush with the bodywork by hand before the soft-top module is installed.Note Please always follow the guidance in the latest service literature whenever carrying out any repairs.12 BackForwards Ξ ContentsComponentsSoft-top frameIn order to be able to achieve the complex folding process for the soft-top, a large number of individual components is required. Thus the soft-top frame includes a front bow, roof bow 1, roof bow 2 and the rear window frame for tensioning the soft-top fabric. More than 20 lateral links and arms on each side guide the roof bows and the rear window frame when the top is raised/lowered and make sure it moves in exactly the right way. Those multi-joint hinges are mounted on a 2-piece main pillar, as are the right and left main mountings.Front roof bow Roof bow 1 Roof bow 2Rear window frame653_100Soft-top fabricThe Audi R8 Spyder has a lightweight soft-top, the fabric of which is made up of the outer fabric and inner liner. Between the front roof bow and roof bow 2, and in the area of the fins, there is insulation that is intended primarily to optimise noise levels when driving with the top up.Front roof bow Roof bow 1 Soft-top fabric Roof bow 2 Rear window frame Inner liningInsulation653_10113 BackForwards Ξ ContentsWindbreakBy making improvements to the aerodynamics in specific areas, it has been possible to reduce the air turbulence in the head area when the top is down. For even greater comfort, the wind deflector made of synthetic fabric has been carried over from the previous model. In keeping with the purist appeal of the Audi R8 Spyder, it is slotted into the sockets provided behind the seats. It reduces the back-flow in the head area by around 90% and in the shoulder/ neck area by 80%. If the wind deflector is not in use it can be stowed neatly in a space-saving bag the luggage compartment.653_102653_103Rear windowIn addition to the fabric wind deflector, the rear window can also be used as a wind deflector when the top is down. With the rear window lowered on the other hand, occupants can fully appreciate the characteristic throaty roar of the V10 TFSI engine. When the soft-top is raised, the rear window moves up to its highest position, and when the top is down it can either be fully lowered or set to the wind deflector position, in other words not quite fully raised.653_104Reference More information on the rear window positions can be found in this self-study programme in the section "Soft-top control" starting on page 55.14 BackForwards Ξ ContentsWater drainageUnder normal operating conditions, the soft-top is wind-proof and waterproof. Only in extremely bad weather such as torrential downpours or very long periods of continuous rain may a few droplets of water possibly find their way into the inside of the car. Rain or splash-water that drips from the rear window or runs into the soft-top compartment is channelled off through the left and right fuel tank sensor covers and between the fuel tank and the heat shield by a special water drainage concept. In the event of complaints in that connection, the outlet of the water drain hose should be checked for dirt. Furthermore, care should be taken to ensure that the water drain hose of the soft-top compartment water drip tray is fully inserted into the water drain hose of the rear window module and that the end of the hose has an unrestricted outlet between the fuel tank and the heat shield.Water drain653_105Sealing systemA sealing system provides for a dry interior and minimal wind noise when the soft-top is raised and the door windows are closed. The sealing system consists of an inner door seal, the inner door seal moulding on the B-pillar, a 3-piece seal for the soft-top compartment cover, and several seals on the front and sides of the softtop.653_106Note When fitting the seals it is essential to pay attention to the correct sequence in which the door inner seal is applied to the body flange as well as the correct fitted positions and that the adjacent seals overlap correctly. More information on the subject can be found in the current service literature.15 BackForwards Ξ ContentsSoft-top control systemSoft-top drive unitInstallation locationsThe next 4 pages provide an overview of the components that are part of the system.Right-hand switch for soft-top lock ready E894Right-hand switch for soft-top latch closed E892Switch for soft-top latch open F294Left-hand switch for soft-top latch closed E891 Left-hand switch for soft-top lock ready E893 Left-hand switch for soft-top flap extended F427 Left-hand switch for soft-top compartment cover centre position F428 Left-hand soft-top flap motor V383 Left-hand switch for tensioner bar up F432 Switch for soft-top stowed F171 Left-hand switch for tensioner bar down F419 Left-hand switch for soft-top flap retracted F42416 BackForwards Ξ ContentsPower operated convertible top valve 3 N342 Power operated convertible top valve 4 N503 Power operated convertible top valve 2 N341 Power operated convertible top valve 5 N504 Right-hand soft-top flap motor V381 Right-hand switch for tensioner bar up F431 Right-hand switch for soft-top flap extended F426 Right-hand switch for soft-top compartment cover centre position F429 Right-hand switch for soft-top flap retracted F425 Right-hand switch for tensioner bar down F420 Right-hand switch for soft-top compartment cover lock released F422 Right-hand switch for soft-top compartment cover lock fastened F421Hydraulic pump for soft-top operation V118 Valve 1 for automatic soft-top N272Left-hand switch for soft-top compartment cover lock released F418 Left-hand switch for soft-top compartment cover lock fastened F417 Switch for soft-top compartment cover closed F519 Switch for soft-top compartment cover open F407 Hydraulic pump relay for soft-top operation J321 Hydraulic pump relay 2 for soft-top operation J588653_04317 BackSwitch for rear window down F416Forwards Ξ ContentsSoft-top operation control unit J256Button for lowering soft-top E36118 BackHall-effect sensor for rear window motor G952 and Hall-effect sensor 2 for rear window motor G953Forwards Ξ ContentsRear window motor V456653_044Button for soft-top operation E13719 BackForwards Ξ ContentsOverviewThe soft-top of the Audi R8 Spyder is available exclusively as a fully automatic fabric top. The soft-top drive system is electro-hydraulic. When the top is down, it is folded away in the soft-top compartment. The soft-top compartment cover covers the soft-top and the soft-top compartment. Soft-top operation is controlled by the soft-top control unit J256. The soft-top requires about 20 s for the opening/closing sequence. Objects placed on the soft-top compartment cover or in the softtop compartment while the soft-top is in operation can cause damage to the vehicle or the components.Soft-top lock catches on windscreen frameRoof bow 1 Roof bow 2Rear window moduleRear window frame653_045Front roof bowSoft-top finSoft-top compartment cover lock catches20 BackForwards Ξ ContentsRisk of injury from moving parts of the soft-topThe hydraulic system is de-pressurised about 5 minutes after it was last operated. If the soft-top is in an intermediate position and the hydraulic system de-pressurises, the soft-top may collapse and the soft-top compartment cover close, depending on its position.Note: The system can also be de-pressurised manually. To do so, the ignition has to be switched off and the soft-top operation button E137 pressed forwards or pulled back for about 5 s.Note When carrying out work on the soft-top system, please note that there is a risk of injury from moving parts. Be aware that the soft-top may collapse and the soft-top compartment cover can move while the system is de-pressurised. Do not reach into moving parts of the soft-top.653_046653_047Intermediate position during soft-top operation.If a soft-top operating sequence is interrupted, intermediate positions may result in which the soft-top is folded away in the soft-top compartment but, at the same time, the soft-top compartment cover is open and the soft-top flaps have not reached their "fully retracted" positions.Note Closing the soft-top compartment cover manually from such an intermediate position can cause damage to the soft-top or the soft-top flaps because the soft-top flaps may collide with the soft-top.Soft-top compartment coverSoft-top flapSoft-top653_048 21 BackForwards Ξ ContentsSoft-top operation and display indicationsBasic features of soft-top operating button E137The soft-top operating button E137 has 2 actions. Pulling back the soft-top operating button E137 lowers the soft-top and pushing the button forwards raises the soft-top. As well as the manual operating sequence, the soft-top also has an automatic operating sequence. For more information on the soft-top automatic operating sequence and the soft-top operating button E137, refer to page 23 and page 35.653_049Manual soft-top operating sequenceDuring a manual soft-top operating sequence, the soft-top operating button E137 has to be held continuously in the operating position, i.e. pressed forwards or pulled back. If the soft-top operating button E137 is released, the soft-top operating sequence stops instantaneously. If the button is operated again, the soft-top operating sequence continues.Closing of side windows and rear window • If the soft-top operating button E137 continues to be operated after the soft-top is lowered, the side windows are raised. • If the soft-top operating button E137 continues to be operated after the soft-top is raised, the side windows and the rear window are raised. • If the button is released after the soft-top is raised or lowered, the side windows/rear window do not move. If the button is then held in the relevant position again, the side windows or side windows and rear window are raised accordingly. • Closing of the side windows and rear window is subject to a time limit of roughly 5 s. • If the button is held in the relevant position again within the time limit of 5 s, the side windows or side windows and rear window are raised accordingly. If the time limit of 5 s expires while the windows are being raised, the side windows/rear window stop moving. • If the button is not operated until after the 5 s have elapsed, the windows do not move. • The 5 s time limit for window closing starts from the point at which the soft-top operation control unit J256 detects that the soft-top is fully lowered or fully raised. • If the soft-top is raised and the soft-top operating button E137 is pulled back to lower the soft-top and then released again (automatic sequence not activated), the side windows lower by a defined amount. The rear window opens completely. The soft-top operating sequence does not start. If the soft-top operating button E137 is then pushed forwards and held within the next 5 s, the side windows and the rear window close again. • The rear window is automatically opened if the soft-top is raised when the rear window is not already open. This provides a "one-button operation" function when closing using the soft-top operating button E137.Note The automatic closing function for the side windows and the rear window after raising the soft-top is not available on vehicles sold in some countries such as the USA due to legal requirements. In such cases, the side windows and the rear window do not automatically close. In that case there is the possibility of closing the rear window and the side windows within 5 s of the soft-top reaching its fully raised position using the rear window opening button E361.22 BackForwards Ξ ContentsAutomatic soft-top operating sequenceTo initiate the automatic soft-top operating sequence, the soft-top operating button E137 must be operated and quickly released within 0.5 s while the vehicle is travelling at between 6 kph and 50 kph. The soft-top then raises or lowers itself automatically depending on whether the button is pushed forwards or pulled back. If the soft-top operating button E137 is operated again while the automatic operating sequence is in progress, the automatic sequence stops. The soft-top operating sequence can then be resumed manually or automatically. When the vehicle is stationary or travelling at less than 6 kph or more than 50 kph, the automatic soft-top operating sequence cannot be activated. At the end of an automatic soft-top operating sequence, the side windows also close. The rear window does not automatically close.OpeningAt 6 - 50 kph653_051653_050ClosingAt 6 - 50 kph653_053653_052Note The automatic closing function for the side windows is not available on vehicles sold in some countries such as the USA due to legal requirements. In such cases, the side windows do not automatically close.23 BackForwards Ξ ContentsGraphical display indications on instrument cluster for soft-top operating sequenceOn the Audi R8 Spyder there is no separate indicator lamp for the soft-top operating sequence. Instead, the soft-top operating sequence is indicated graphically on the instrument cluster. Depending on the setting in the Audi virtual cockpit, the indications appear in the centre or at the side. As soon as the soft-top operating sequence is started, a graphical representation of the vehicle with highlighted soft-top and soft-top compartment cover appears on the instrument cluster display. A curved arrow over the soft-top indicates the direction in which the top is moving: • Arrow pointing backwards: soft-top is opening. • Arrow pointing forwards: soft-top is closing. • No arrow shown: the soft-top is in an intermediate position or has reached the fully raised/lowered position. The soft-top and the soft-top compartment cover are shown in red in similar fashion to when a door or the bonnet or boot is open.Soft-top indication653_026Indication during automatic soft-top operating sequenceIndication if automatic soft-top operating sequence interrupted653_037653_020During an automatic soft-top operating sequence, an "A" is displayed at the beginning of the arrow.If no arrow is displayed over the soft-top, the soft-top operating sequence has been initiated and then abandoned. The soft-top is therefore in an intermediate position.Reference For further information on the Audi virtual cockpit, refer to Self Study Programme 628 "Audi virtual cockpit".24 BackIndication when automatic soft-top operating sequence completed Once the soft-top operating sequence is completed, the status of the soft-top and the soft-top compartment cover (open or closed) is indicated for about 2 s. An audible signal sounds at the same time.Forwards Ξ ContentsSoft-top operating sequence complete – soft-top loweredSoft-top operating sequence complete – soft-top raised653_025653_093Indications if soft-top operating sequence is not possibleIf the soft-top cannot be operated, this is indicated on the instrument cluster. An audible signal sounds at the same time. A warning and 7 different messages can also be displayed.Warning display The warning is given if the soft-top is in an intermediate position and if the event memory simultaneously contains a static entry and the vehicle is travelling faster than 5 kph. In addition to the warning, the yellow central warning lamp comes on.Indication on red-highlighted tab for driver information and indicator lamps Vehicle/soft-top symbol shown in yellow on the status bar Message displayedSoft-top: Malfunction! Continuation of journey only possible within limitations. See owner's manual653_03625 BackDisplay of messages Other reasons why a soft-top operating sequence is not possible are displayed as messages. • When messages about the soft-top are displayed, the yellow central warning lamp does not come on. • When the messages are displayed, the vehicle/soft-top symbol appears on the status bar. • The messages are not added to the driver information and warning lamps tab.Forwards Ξ ContentsNote: If the soft-top is at the limit of its travel in either direction (fully lowered or fully raised) and a soft-top operating sequence is initiated in the direction of travel for which the limit has been reached, "no" actions are initiated and no messages are displayed.This message is displayed if the soft-top is at the limit of its travel in either direction and the soft-top operating button E137 is operated to move the soft-top in the direction of travel opposite to that for which the limit has been reached, and the vehicle is travelling at a speed of 50 kph or more. In that case, a soft-top operating sequence is not started.Soft-top: operation not possible at present. Vehicle speed too high.653_024This message is displayed in the following situations: • If a soft-top operating sequence is active, the vehicle's speed increases to 55 kph and the soft-top operating sequence is abandoned. • Or: If a soft-top operating sequence was active or abandoned (soft-top operating button E137 was released) and therefore the soft-top is in an intermediate position. The vehicle's speed subsequently increases to at least 50 kph and the soft-top operating sequence is to be continued (button is operated again). In that case, the soft-top operating sequence is not resumed.Soft-top: not at limit of travel. Vehicle speed too high653_023This message is displayed if the ambient temperature is below -15 °C, the soft-top is raised and the soft-top operating button E137 is operated for "lowering" the soft-top. If the soft-top is down at temperatures below -15 °C, it can still be raised.Soft-top: operation not possible at present. Outside temperature too low.653_03326 BackThis message is displayed in the following situations: • If a static event is present that prevents a soft-top operating sequence when the soft-top operating button E137 is operated. • Or: If the bonnet is openForwards Ξ ContentsSoft-top: operation not possible.653_027This message appears if the soft-top operating switch E137 is operated when the ignition is switched on and the engine is not running and the battery voltage has dropped below a certain level. Once the engine has started, the soft-top can again be raised or lowered.Soft-top: operation not possible at present. Engine needs to be running653_028This message is displayed if the overheat cut-out (overload cut-out) has tripped and the soft-top operating button E137 is operated.Soft-top: operation not possible at present.653_029This message is displayed if the soft-top control unit J256 has registered a static event, a limit of travel (fully raised or fully lowered) has been reached and the soft-top operating button E137 is operated and then released.Soft-top: Malfunction! Journey can be continued.653_03027 BackForwards Ξ ContentsFunctional sequence when raising and lowering the soft-topSoft-top opening sequenceFor the soft-top to be lowered, the following conditions must be satisfied: • The vehicle speed must be under 50 kph. • The ignition must be switched on.• The outside temperature must be above -15 °C. • The battery must have sufficient voltage. • The bonnet must be closed.Initial situation: the soft-top is raisedStarting the lowering sequence If all conditions have been met, the lowering sequence can be initiated by pulling back and holding the soft-top operating button E137. If the vehicle is travelling at a speed of between 6 kph and 50 kph, simply pulling back and quickly releasing the button (within 0.5 seconds) is sufficient to the start the automatic soft-top operating sequence.If the side windows and the rear window are not yet open, the side windows open by a certain amount and the rear window opens completely.653_011Indication on instrument cluster display Afterwards, a graphical depiction appears on the instrument cluster showing the vehicle with the soft-top partly lowered, the soft-top compartment cover open and a curved arrow. The arrow is pointing backwards. When an automatic soft-top operating sequence is in progress, an "A" is displayed at the start of the arrow. If the rear window heater is on, it is switched off.653_037Note The rear window heater can only be switched on when the soft-top is raised.28 BackSoft-top opening The soft-top fins move up into an upright position (1). The soft-top compartment cover lock catches are then unlocked (2).Forwards Ξ Contents1 2653_012The soft-top compartment cover opens. Once the soft-top compartment cover has reached the limit of its travel (3), the soft-top lock catches on the windscreen frame open (4).43653_013The soft-top folds down into the soft-top compartment. At the same time, the soft-top flaps move into the centre position and stop there (5). The soft-top is completely stowed away in the soft-top compartment (6).5 6653_014The soft-top flaps move into the "extended" position (7).7653_015The soft-top compartment cover closes (8). The soft-top compartment cover lock catches are locked (9). If the convertible top operating switch E137 is kept pressed, the side windows close but the rear window remains open. The same sequence takes place with the automatic sequence.89653_016Note The automatic closing function for the side windows is not available on vehicles sold in some countries such as the USA due to legal requirements. In such cases, the side windows do not automatically close.Indication on instrument cluster display An audible signal and a graphical indication on the instrument cluster indicate that the soft-top operating sequence is complete and the soft-top is down.653_025 29 BackForwards Ξ ContentsFunctional sequence when raising the soft-topFor the soft-top to be raised, the following conditions must be satisfied: • The vehicle speed must be under 50 kph. • The ignition must be switched on.• The battery must have sufficient voltage. • The bonnet must be closed.Initial situation: the soft-top is downStarting the raising sequence If all conditions have been met, the raising sequence can be initiated by pushing forwards and holding the soft-top operating button E137. If the vehicle is travelling at a speed of between 6 kph and 50 kph, simply pressing back and quickly releasing the button (within 0.5 seconds) is sufficient to the start the automatic soft-top operating sequence.If the side windows and the rear window are not yet open, the side windows open by a certain amount and the rear window opens completely.653_115Indication on instrument cluster display Afterwards, a graphical depiction appears on the instrument cluster showing the vehicle with the soft-top partly lowered, the soft-top compartment cover open and a curved arrow. The arrow is pointing forwards. When an automatic soft-top operating sequence is in progress, an "A" is displayed at the start of the arrow.653_038Note The rear window heater can be switched on again.30 BackSoft-top closing The soft-top compartment cover lock catches are unlocked (1). The soft-top compartment cover opens (2) and the soft-top flaps move into the "retracted" position (3).Forwards Ξ Contents32 1653_116As soon as the soft-top flaps have reached the "centre position" (4), the soft-top moves out of the soft-top compartment (5).54653_117When the soft-top flaps have reached the "retracted" position (6) they remain in that position and the soft-top moves to the raised position (7).7 6653_118The soft-top lock catches on the windscreen frame are locked (8). The soft-top compartment cover closes (9). The soft-top compartment cover lock catches are locked (10).8910653_119The soft-top fins move down and tension the soft-top (11). If the convertible top operating switch E137 is kept pressed, the side windows and the rear window close. The same sequence takes place with the automatic sequence.11653_120Note The automatic closing function for the side windows is not available on vehicles sold in some countries such as the USA due to legal requirements. In such cases, the side windows do not automatically close.Indication on instrument cluster display An audible signal and a graphical indication on the instrument cluster indicate that the soft-top operating sequence is complete and the soft-top is raised.653_026 31 BackForwards Ξ ContentsOperating the soft-top using the driver's door lock cylinderThe soft-top can be raised or lowered using the driver's door lock cylinder. This can be done using the integrated emergency key or the socalled wallet key.Lowering For the soft-top to be lowered, the following conditions must be satisfied: • The vehicle speed must be 0 kph. • The battery must have sufficient voltage. • The outside temperature must be above -15 °C. • The bonnet must be closed. To lower the soft-top, first unlock the vehicle with the remote control key. Then turn the driver's door lock cylinder in "unlocking" direction using the emergency/wallet key (1). If the emergency/wallet key is then turned in "unlock" direction again within 2 s and held in that position (2), the soft-top operating sequence starts. The emergency/wallet key must be held in the "unlock" position throughout the soft-top operating sequence. If the emergency/wallet key is released, the soft-top operating sequence stops immediately. If the soft-top operating sequence is to be resumed, the emergency/wallet key must be turned in "unlock" direction again and held in that position. If the emergency/wallet key is turned in "lock" direction and held in that position, the soft-top is raised again.1.Turn key again within 2 seconds2.Lowering For the soft-top to be raised, the following conditions must be satisfied: • The vehicle speed must be 0 kph. • The battery must have sufficient voltage. • The bonnet must be closed. To raise the soft-top, turn the driver's door lock cylinder in "locking" direction using the emergency/wallet key (1).653_054If the emergency/wallet key is then turned in "lock" direction again within 2 s and held in that position (2), the soft-top operating sequence starts. The emergency/wallet key must be held in the "lock" position throughout the soft-top operating sequence. If the emergency/wallet key is released, the soft-top operating sequence stops immediately. If the soft-top operating sequence is to be resumed, the emergency/wallet key must be turned in "lock" direction again and held in that position. If the emergency/wallet key is turned in "unlock" direction and held in that position, the soft-top is lowered again.1.2.Turn key again within 2 seconds653_055Note If the soft-top is operated using the emergency/wallet key, there is a delay before the soft-top operating sequence starts.32 BackForwards Ξ ContentsOperating the soft-top using the remote control key fobThe soft-top can be raised or lowered using the buttons on the remote control key fob.Raising For the soft-top to be lowered, the following conditions must be satisfied: • The vehicle speed must be 0 kph. • The battery must have sufficient voltage. • The outside temperature must be above -15 °C. • The bonnet must be closed. • The remote control key must not be more than about 6 m away from the vehicle. To lower the soft-top, press the unlock button on the remote control key fob. If, within 2 s, the button is pressed again and held, the soft-top operating sequence starts. The button must be kept pressed throughout the soft-top operating sequence. If the button is released, the soft-top operating sequence stops immediately. If the soft-top operating sequence is to be resumed, the button must be pressed and held again. If the lock button on the remote control key fob is pressed and held, the soft-top is raised again.653_056Raising For the soft-top to be raised, the following conditions must be satisfied: • The vehicle speed must be 0 kph. • The battery must have sufficient voltage. • The bonnet must be closed. • The remote control key must not be more than about 6 m away from the vehicle. To raise the soft-top, press the lock button on the remote control key fob. If, within 2 s, the button is pressed again and held, the soft-top operating sequence starts. The button must be kept pressed throughout the soft-top operating sequence. If the button is released, the soft-top operating sequence stops immediately. If the soft-top operating sequence is to be resumed, the button must be pressed and held again. If the unlock button on the remote control key fob is pressed and held, the soft-top is lowered again.653_057Note If the soft-top is operated using the remote control key fob buttons, there is a delay before the soft-top operating sequence starts.33 BackForwards Ξ ContentsBonnetIf the bonnet is open, no soft-top operating sequence is possible. The driver is visually notified by the following message on the instrument cluster.Soft-top: operation not possible.653_027The bonnet can be opened when the soft-top is up, down or in an intermediate position.Note If the soft-top compartment cover is open when the soft-top is in an intermediate position and the bonnet is then opened, the bonnet may strike the soft-top compartment cover and be damaged if fully opened.653_05834 BackForwards Ξ ContentsOperating the soft-top while drivingThe soft-top can be raised or lowered using the soft-top operating button E137 as long as the vehicle speed is below 50 kph. If the vehicle's speed increases to over 55 kph during soft-top operating sequence, the driver is alerted visually and audibly. A soft-top operating sequence cannot be initiated if the vehicle is travelling at a speed of 50 kph or higher. In that case too, the driver is alerted by audible and visual warnings.Soft-top: operation not possible. Vehicle speed too high.653_024Components of the soft-top control systemSoft-top operating button E137The soft-top operating button is integrated in the centre console. It initiates the soft-top raising/lowering sequence. If the soft-top operating button E137 sends the "actuated" signal for about 60 s (time-out), the static event "soft-top raising/lowering button – implausible signal" is registered in the event memory. This can occur, for example, if the soft-top operating button E137 is inadvertently continuously operated by an object (briefcase, mobile phone etc.). As soon as the soft-top operating button E137 is free again, the event memory entry changes to "sporadic". It is again possible to operate the soft-top.653_05935 BackForwards Ξ ContentsHydraulic cylindersThe soft-top is equipped with 4 pairs of hydraulic cylinders. • 1 pair of cylinders is for operating the soft-top fins (tensioner bar) • 1 pair of cylinders is for operating the soft-top compartment cover • 1 pair of cylinders is for operating the soft-top • 1 pair of cylinders is for operating the soft-top compartment cover locks In addition, the soft-top has a single cylinder for operating the soft-top locks.Cylinder for operating the soft-top locks653_060Cylinder for operating the soft-top finsCylinder for operating the soft-top compartment coverCylinder for operating the soft-top compartment cover locksCylinder for operating the soft-topDesign of a hydraulic cylinder The hydraulic cylinders can be operated in both directions and are, therefore, double-acting.Piston end Hydraulic cylinder Piston-rod endPiston rodHydraulic line Hydraulic connection Piston Hydraulic connection653_06136 BackForwards Ξ ContentsSoft-top operation hydraulic pump V118The hydraulic pump for soft-top operation V118 contains the following components: • Hydraulic pump relay for soft-top operation J321 • Hydraulic pump relay 2 for soft-top operation J588 • Automatic soft-top valve 1 N272 • Automatic soft-top valve 2 N341• Automatic soft-top valve 3 N342 • Automatic soft-top valve 4 N503 • Automatic soft-top valve 5 N504The hydraulic pump forms a single unit together with the relays and the electro-hydraulic valves. The hydraulic pump is located below the rear window module.653_062Hydraulic pump relay for soft-top operation J321Hydraulic pump relay 2 for soft-top operation J588Hydraulic pump relay for soft-top operation J321 and hydraulic pump relay 2 for soft-top operation J588 The direction of rotation of the hydraulic pump V118 is controlled by the two relays J321 and J588. The soft-top operation control unit J256 controls the deployment of the two relays. Based on the direction of rotation of the hydraulic pump, the electro-hydraulic valves direct the oil into the hydraulic cylinders so that the softtop, the soft-top fins, the soft-top compartment cover, the soft-top compartment cover locks and the soft-top locking mechanism move in the required direction. Which electro-hydraulic valve is responsible for which component is explained on the next couple of pages.37 BackForwards Ξ ContentsHydraulic pump valvesAutomatic soft-top valve 1 N272 Automatic soft-top valve 1 N272 directs the oil from the hydraulic pump to the hydraulic cylinders that are responsible for raising and lowering the soft-top fins. When the hydraulic pump is running, pressure is applied to the piston-rod ends of the hydraulic cylinders, see page 36. It makes no difference in this case in which direction the pump is rotating. The piston ends (see page 36) of the hydraulic cylinders are differentially actuated. That means that the direction of rotation of the hydraulic pump changes according to the operation required. Consequently, there is either pressure or no pressure acting on the piston ends of the cylinders. If pressure is applied to the piston ends of the cylinders, the piston rods are forced out of the cylinders due to the larger effective surface areas. Since the piston rods are attached to the soft-top fins, the soft-top fins move downwards past the point of equilibrium and tension the soft-top. If no pressure is applied to the piston ends of the cylinders, the piston rods are forced back into the cylinders due to the pressure constantly acting on the piston-rod ends. Since the piston rods are attached to the soft-top fins, the soft-top fins move upwards and release the tension on the soft-top.Automatic soft-top valve 3 N342 (locks and unlocks the soft-top compartment cover)Automatic soft-top valve 2 N341 Automatic soft-top valve 2 N341 is responsible for closing the soft-top compartment cover. Valve 2 directs the oil from the hydraulic pump to the hydraulic cylinders that are responsible for moving the soft-top compartment cover. When valve 2 switches over, the hydraulic fluid flows into the piston ends of the hydraulic cylinders. No pressure is acting on the piston-rod ends. When pressure is applied to the piston ends of the cylinders, the piston rods are forced out of the cylinders. Since the piston rods are attached to the soft-top compartment cover, the soft-top compartment cover closes due to the action of the mechanical linkage.Automatic soft-top valve 3 N342 Automatic soft-top valve 3 N342 directs the oil from the hydraulic pump to the hydraulic cylinders that are responsible for locking/ unlocking the soft-top compartment cover. When the hydraulic pump is running, pressure is applied to the piston-rod ends of the hydraulic cylinders. It makes no difference in this case in which direction the pump is rotating. The piston ends of the hydraulic cylinders are differentially actuated. That means that the direction of rotation of the hydraulic pump changes according to the operation required. Consequently, there is either pressure or no pressure acting on the piston ends of the cylinders. If pressure is applied to the piston ends of the cylinders, the piston rods are forced out of the cylinders due to the larger effective surface areas. Since the piston rods are attached to the soft-top compartment cover lock, the catches release the soft-top compartment cover due to the action of the mechanical linkage. If no pressure is applied to the piston ends of the cylinders, the piston rods are forced back into the cylinders due to the pressure constantly acting on the piston-rod ends. Since the piston rods are attached to the soft-top compartment cover lock, the catches lock the soft-top compartment cover due to the action of the mechanical linkage.38Automatic soft-top valve 1 N272 (raises and lowers the soft-top fins) BackForwards Ξ ContentsAutomatic soft-top valve 4 N503Automatic soft-top valve 4 N503 (locks and unlocks the soft-top)Automatic soft-top valve 2 N341 (closes the soft-top compartment cover)Automatic soft-top valve 4 N503 directs the oil from the hydraulic pump to the hydraulic cylinder that is responsible for locking/ unlocking the soft-top to the windscreen frame. When the hydraulic pump is running, pressure is applied to the piston-rod end of the hydraulic cylinder. It makes no difference in this case in which direction the pump is rotating. The piston end of the hydraulic cylinder is differentially actuated. That means that the direction of rotation of the hydraulic pump changes according to the operation required. Consequently, there is either pressure or no pressure acting on the piston end of the cylinder. If pressure is applied to the piston end of the cylinders, the piston rod is forced out of the cylinder due to the larger effective surface area. As the piston rod is attached to the linkage for the soft-top lock catches, the catches open and release the soft-top from the windscreen frame. If no pressure is applied to the piston ends of the cylinders, the piston rod is forced back into the cylinder due to the pressure constantly acting on the piston-rod end. As the piston rod is attached to the linkage for the soft-top lock catches, the catches close and lock the soft-top to the windscreen frame.Automatic soft-top valve 5 N504 Automatic soft-top valve 5 N504 is responsible for opening the soft-top compartment cover. Valve 5 directs the oil from the hydraulic pump to the hydraulic cylinders that are responsible for moving the soft-top compartment cover. When valve 5 switches over, the hydraulic fluid flows into the piston-rod ends of the hydraulic cylinders. No pressure is acting on the piston ends. When pressure is applied to the piston-rod ends of the cylinders, the piston rods are forced back into the cylinders. Since the piston rods are attached to the soft-top compartment cover, the soft-top compartment cover opens due to the action of the mechanical linkage.653_063Automatic soft-top valve 5 N504 (opens the soft-top compartment cover)Hydraulic valve inside soft-top operation hydraulic pump V118 (raises and lowers the soft-top)Valve for moving the soft-top The movement of the soft-top itself is not controlled by means of an electro-hydraulic valve. So that the movement of the soft-top can be effected, there is a hydraulic valve inside the hydraulic pump V118. That hydraulic valve directs the oil from the hydraulic pump to the hydraulic cylinders that are responsible for raising/ lowering the soft-top. When the soft-top is lowered, relay J321 causes the hydraulic pump to rotate in the direction that applies pressure to the piston-rod ends of the hydraulic cylinders. The piston ends are not under pressure at this point. When pressure is applied to the piston-rod ends of the cylinders, the piston rods are forced back into the cylinders. Since the piston rods are attached to the main mounting of the soft-top, the soft-top is lowered due to the action of the mechanical linkage. When the soft-top is raised, relay J588 causes the hydraulic pump to rotate in the direction that applies pressure to the piston ends of the hydraulic cylinders. The piston-rod ends are not under pressure at this point. When pressure is applied to the piston ends of the cylinders, the piston rods are forced out of the cylinders. Since the piston rods are attached to the main mounting of the soft-top, the soft-top is raised due to the action of the mechanical linkage.39 BackForwards Ξ ContentsOverheat cut-outIn order to protect the soft-top operation hydraulic pump V118 against overload, the soft-top operation control unit J256 monitors the running time of the hydraulic pump and switches it off if necessary. Activation of overheat cut-out The overheat cut-out is activated in 2 stages. An appropriate message is displayed on the instrument cluster if the overheat cut-out has been activated.Soft-top: no operation possible.• Stage 1: stage 1 starts when the soft-top (hydraulic pump) has been operating constantly for 120 s. If a soft-top lowering sequence is currently in progress at the point when the 120 s time-limit is reached, the lowering sequence can be completed outside of the 120 s limit. However, if the lowering sequence is stopped, it cannot be653_029restarted. That means the soft-top then remains in an intermediate position. Even if stage 1 of the overheat cut-out function has been triggered, the soft-top can still be raised once. After stage 1, there is a delay of roughly 10 min until it is possible to operate the soft-top again.• Stage 2: stage 2 starts when the soft-top (hydraulic pump) has been operating constantly for 200 s. In this case it makes no difference what position the soft-top happens to be in at that point or whether it is being raised or lowered. As soon as stage 2 of theoverheat cut-out function has been triggered, the soft-top cannot be operated at all. After stage 2, there is a delay of roughly 20 min until it is possible to operate the soft-top again.Soft-top flapsThe left and right-hand soft-top flaps are each extended/retracted by an actuating arm that is driven by an electric motor. The actuating arm on the right-hand side of the vehicle is driven by the right-hand soft-top flap motor V381, and the one on the left by the left-hand soft-top flap motor V383. The soft-top flaps cover the main mountings when the soft-top is down. When the soft-top is raised, the soft-top flaps are retracted. The position of the left-hand soft-top flap is detected by 3 microswitches: • Left-hand soft-top flap retracted switch F424 • Left-hand soft-top flap extended switch F427 • Left-hand soft-top compartment cover centre position switch F428 The position of the right-hand soft-top flap is detected by 3 microswitches: • Right-hand soft-top flap retracted switch F425 • Right-hand soft-top flap extended switch F426 • Right-hand soft-top compartment cover centre position switch F429 The soft-top operation control unit J256 analyses the signals from the microswitches and operates the soft-top flaps and/or the soft-top accordingly.L/H soft-top flap653_064R/H soft-top flap40 BackForwards Ξ ContentsRight-hand soft-top flap motor V381The right-hand soft-top flap motor V381 is fitted on the right-hand side of the vehicle, as seen when facing forwards. The motor drives the right-hand soft-top flap via an actuating arm. The motor does not have its own switches or sensors. It is monitored by the softtop operation control unit J256 and is diagnosable.Right-hand soft-top flap motor V381653_065Left-hand soft-top flap motor V383Left-hand soft-top flap motor V383The left-hand soft-top flap motor V383 is fitted on the left-hand side of the vehicle, as seen when facing forwards. The motor drives the left-hand soft-top flap via an actuating arm. The motor does not have its own switches or sensors. It is monitored by the softtop operation control unit J256 and is diagnosable.41 BackForwards Ξ ContentsRight-hand soft-top flap retracted switch F425The right-hand soft-top flap retracted switch F425 is fitted on the console of the right-hand soft-top flap, as seen when facing forwards. The switch is a microswitch. When the soft-top flap is retracted, the microswitch is operated by the actuating arm that operates the soft-top flap. The left-hand soft-top flap retracted switch F424 and the righthand soft-top flap retracted switch F425 are wired in series with one another. For the soft-top operation control unit J256 to be able to detect the "switched" signal, both switches have to be switched at the same time. The event memory can register the event "implausible signal" for those switches. If an event is present at one of the switches, that event is registered for both switches even though it is only present on one side.Left-hand switch for soft-top flap retracted F424Right-hand switch for soft-top flap retracted F425653_066Left-hand switch for soft-top flap retracted F424Left-hand soft-top flap retracted switch F424The left-hand soft-top flap retracted switch F424 is fitted on the console of the left-hand soft-top flap, as seen when facing forwards. The switch is a microswitch. When the soft-top flap is retracted, the microswitch is operated by the actuating arm that operates the soft-top flap. The left-hand soft-top flap retracted switch F424 and the righthand soft-top flap retracted switch F425 are wired in series with one another. For the soft-top operation control unit J256 to be able to detect the "switched" signal, both switches have to be switched at the same time. The event memory can register the event "implausible signal" for those switches. If an event is present at one of the switches, that event is registered for both switches even though it is only present on one side.42 BackForwards Ξ ContentsRight-hand soft-top flap extended switch F426The right-hand soft-top flap extended switch F426 is fitted on the console of the right-hand soft-top flap, as seen when facing forwards. The switch is a microswitch. When the soft-top flap is extended, the microswitch is operated by the actuating arm that operates the soft-top flap. The left-hand soft-top flap extended switch F427 and the righthand soft-top flap extended switch F426 are wired in series with one another. For the soft-top operation control unit J256 to be able to detect the "switched" signal, both switches have to be switched at the same time. The event memory can register the event "implausible signal" for those switches. If an event is present at one of the switches, that event is registered for both switches even though it is only present on one side.Right-hand switch for soft-top flap extended F426653_067Left-hand switch for soft-top flap extended F427Left-hand soft-top flap extended switch F427The left-hand soft-top flap extended switch F427 is fitted on the console of the left-hand soft-top flap, as seen when facing forwards. The switch is a microswitch. When the soft-top flap is extended, the microswitch is operated by the actuating arm that operates the soft-top flap. The left-hand soft-top flap extended switch F427 and the righthand soft-top flap extended switch F426 are wired in series with one another. For the soft-top operation control unit J256 to be able to detect the "switched" si