TECHNICAL DOCUMENTATION
SSP 657 Audi Q5 (type FY)

This PDF is currently unavailable.
Read document text
Audi Q5(type FY)Self Study Programme 657For internal use only.Audi Service Training BackA best-selling Audi is even more powerful and sporty – with the new Audi Q5, the brand with the four rings has set the bar a notch higher. Among the great innovations are the quattro drive system with ultra technology, highly efficient engines, the air suspension with damper control and a comprehensive line-up of infotainment and assistance systems. The car's masculine and sporty character stands out immediately. The front end of the Audi Q5 is comparatively flat and dominated by horizontal lines matching those of the singleframe grille. A thick aluminium-style frame extending to the headlights accentuates the dominance of the singleframe grille. Viewed side-on, the flowing lines accentuate the sporty character of the new Audi Q5. The roof line culminates in a flat railing and tapers back down early, while the bottom edge of the window cuts upwards just before the C post. A striking and strongly undercut shoulder line emerges from the corners of the headlights as the bonnet shutline and curves elegantly towards the rear where it terminates at the upper edge of the taillights. Distinctively flared wheel arches are a reference to the quattro all-wheel drive system and the Audi DNA. Other Audi styling cues are the aluminium-style trims on the lower parts of the doors and sills. The angular door mirrors are seated on the door shoulders underscoring the sporty look of the new AudiForward Ξ ContentsSUV. Despite having larger dimensions, the occupant cell alone weighs about 20 kg less than that of the previous model. Overall, the new model is up to 90 kg lighter than its predecessor, depending on engine. The keys to this improvement are new solutions in geometric lightweight design and an intelligent material mix with a strong emphasis on aluminium. Production at the San José Chiapa plant (Mexico) The new Audi Q5 is manufactured at a newly constructed San José Chiapa plant in Mexico. The most up-to-date production plant in the Audi organisation has been built on the 460 hectare site. At an altitude of 2,400 meters, it is the highest site in the Audi production network. Located about 200 km to the east of Mexico City, the new Audi plant has an annual production capacity of 150,000 cars. Smart logistics allowing flexible production and supply chains are integral to Audi Mexico. San José Chiapa is the first facility in the entire VW Group to implement such technology for the complete material and container flow process. The new plant has been constructed in line with Audi standards, including those for sustainability and environmental protection.657_002Learning objectives of this self study programme: This self study programme describes the design and function of the Audi Q5 (type FY). Once you have completed this self study programme you will be able to answer questions on the following topics: • • • • Engines used New suspension features New power transmission features New features of the assistance systems.2ContentsIntroductionPresentation __________________________________________________________________________________________________________________________________________________ 4BodyOverview ______________________________________________________________________________________________________________________________________________________ 8 Attachments _________________________________________________________________________________________________________________________________________________ 10EnginesPetrol engines _______________________________________________________________________________________________________________________________________________ 16 Diesel engines _______________________________________________________________________________________________________________________________________________ 17 Engine/gearbox combinations _____________________________________________________________________________________________________________________________ 22Power transmissionOverview _____________________________________________________________________________________________________________________________________________________ 24 quattro with ultra technology _____________________________________________________________________________________________________________________________ 26 7-speed dual clutch gearbox 0CJ __________________________________________________________________________________________________________________________ 38 6-speed manual gearbox with oil injection lubrication _ _________________________________________________________________________________________________ 40 quattro with self-locking centre differential/quattro with sport differential _________________________________________________________________________ 46SuspensionOverall concept ______________________________________________________________________________________________________________________________________________ 48 Axles and wheel alignment ________________________________________________________________________________________________________________________________ 49 Adaptive air suspension (aas) ______________________________________________________________________________________________________________________________ 51 Brake system ________________________________________________________________________________________________________________________________________________ 53 Steering system _____________________________________________________________________________________________________________________________________________ 55 adaptive cruise control (ACC) ______________________________________________________________________________________________________________________________ 56 Wheels and tyres ____________________________________________________________________________________________________________________________________________ 57Electrics and electronicsIntroduction _________________________________________________________________________________________________________________________________________________ 58 Power supply ________________________________________________________________________________________________________________________________________________ 60 Topology _____________________________________________________________________________________________________________________________________________________ 62 Exterior lighting _____________________________________________________________________________________________________________________________________________ 66 Audi drive select _ ____________________________________________________________________________________________________________________________________________ 75Air conditioningIntroduction _________________________________________________________________________________________________________________________________________________ 76 Operation ____________________________________________________________________________________________________________________________________________________ 76 Air conditioners _____________________________________________________________________________________________________________________________________________ 77Safety and driver assistance systemsPassive safety ________________________________________________________________________________________________________________________________________________ 78 Active safety _________________________________________________________________________________________________________________________________________________ 86 Traffic information __________________________________________________________________________________________________________________________________________ 88Infotainment and Audi connectOverview of versions ________________________________________________________________________________________________________________________________________ 92 Sound systems ______________________________________________________________________________________________________________________________________________ 94 Aerials overview _____________________________________________________________________________________________________________________________________________ 96 Control panel ________________________________________________________________________________________________________________________________________________ 98 Audi connect SIM (country-dependent) ________________________________________________________________________________________________________________ 103Inspection and maintenanceOverview ___________________________________________________________________________________________________________________________________________________ 104AppendixSelf study programmes _ __________________________________________________________________________________________________________________________________ 106 The self study programme teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a repair manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. This content is not updated. For further information about maintenance and repair work, always refer to the current technical literature. NoteReference3 BackForward Ξ ContentsIntroductionPresentationThe Q5 (type FY) marks the second generation of Audi's successful SUV for everyday use and leisure combining progressive design and high utility value. It features luxury-class connectivity, infotainment and assistance systems.Engines• 2.0l TFSI engine (185 kW) • 3.0l TFSI engine (260 kW) • 2.0l TDI engine (110 kW – 140 kW) Other engine versions will follow at a later date.Driver assistance systemsThe following systems are available: • Audi pre-sense front • Audi pre-sense basic • Audi pre sense city • Audi pre-sense rear • Emergency assist • adaptive cruise control Stop & Go • Traffic jam assist • Audi side assist • Audi active lane assist • Road sign recognition • Park assist • Rear cross traffic assist • Downhill AssistDisplays and operationThe optional Audi virtual cockpit has a high-resolution 12.3-inch screen. Another optional feature is a head-up display which projects key information onto the windscreen. The infotainment features in the Audi Q5 are similar to those of the Audi A4 (type 8W).Air conditioningClimate control is provided by a single-zone or three-zone deluxe automatic air conditioning system. In addition, the air conditioning system is optionally available with an anti-allergenic dust and pollen filter.4 BackForward Ξ ContentsBodyUnladen weight has been reduced by up to 90 kg, depending on the engine. Steels with maximum tensile strength and aluminium form an intelligent material mix in the body. The two front spring strut mounts are manufactured from die-cast aluminium. They are attached to the adjacent sheetsteel components using punch rivets, flowdrill screws and structural adhesive.SuspensionThe handling of the new Audi Q5 is sporty while being comfortable. Creating the basis for this are the newly developed five-link suspensions and also the new electromechanical power steering system. Dynamic steering is available as an option; it varies its gear ratio according to the driving speed and steering angle. In addition to adapting the damper control system, the new adaptive air suspension can be used to vary the ride height of the car body over five stages.657_109Power transmissionDepending on engine, a 6-speed manual gearbox, a 7-speed dual clutch gearbox or an 8-speed automatic gearbox are available. The quattro drivetrain with ultra technology is a full-time all-wheel-drive system with active rear axle torque vectoring. The automatic gearboxes integrate a fuel-saving freewheel function.Electrical system and electricsThe architecture of the electrical system in the Audi Q5 (type FY) is based on the MLBevo platform architecture. The basic architecture corresponds to that of the Audi A4 (type 8W) and the Audi Q7 (type 4M). The new Q5 uses xenon or LED headlights in conjunction with LED daytime running lights. The matrix LED headlights previously featured on other Audi models are also available.5 BackForward Ξ ContentsDimensions165911331616 1893657_0081609 2140657_0091059 1)9988992819 4663945657_0106759 BackForward Ξ Contents15002)15232)14663)14343)982 1050657_011Exterior dimensions and weightsLength in mm Width (not including exterior mirrors) in mm Width (including exterior mirrors) in mm Height in mm Front track width in mm Rear track width in mm Wheelbase in mm Unladen weight in kg Max. gross weight in kg Drag coefficient cw 4663 1893 2140 1659 1616 1609 2819 17954) 24004) 0.30Inner dimensions and other specificationsFront cabin width in mm Front headroom in mm Front shoulder width in mm Rear headroom in mm Through-loading width in mm Load sill height in mm Luggage compartment capacity in l Capacity of fuel tank in l 15232) 10591) 14663) 998 1050 759 550/15105) 656)/707)Maximum headroom. Elbow room width. 3) Shoulder room width. 4) With 2.0l TFSI engine. 5) Depending on the position of the rear bench seat. 6) With TDI engine. 7) With TFSI engine.1) 2)All dimensions are given in millimetres and refer to the unladen weight of the vehicle.7 BackForward Ξ ContentsBodyOverviewThe Audi Q5 (type FY) has shed some 20 kg in body weight, despite being larger overall than its predecessor. This figure was achieved through a combination of geometric lightweight design and an intelligent material mix. The overall body structure of the Q5 owes its lightness and rigidity to the use of two additional die-cast aluminium strut mountings at the front end as a complement to the customary mix of soft, high-strength, modern high-strength and ultra-high-strength sheet-steel components. They are attached to the adjacent sheet-steel components using punch rivets, flowdrill screws and structural adhesive. Structural adhesive not only strengthens the aluminium-steel joint, but also prevents the contact corrosion that would otherwise occur between these two materials. Straightening and reshaping work in the area of aluminium components or aluminium-steel joints is not approved by the manufacturer as this can damage the aluminium casting or lead to invisible cracks in the component.Key:Sheet aluminium Die-cast aluminium Aluminium profile Ultra-high-strength steel (hot-stamped) Advanced high-strength steel High-strength steel Soft steelJoining techniqueA number of different joining technologies are used to assemble the body of the Q5. In addition to classic resistance spot welding (there are 5656 spot welds on the car), the following technologies are utilised:• • • • MAG welding (total seam length: 1646 mm) Laser soldering (total seam length: 3572 mm) Laser welding (total seam length: 4660) MIG soldering of steel (total seam length: 1838 mm)• • • • Semi-tubular punch rivets (132 pcs.) Flow drill screws (16 pcs.) Seaming (total seam length: 2085 mm) Bonding (total seam length: 61425 mm)8 BackForward Ξ ContentsUltra-high-strength hot-shaped componentsHot-shaped components form the high-strength, crash-safe backbone of the occupant cell. They strengthen the transition from the front end to the cabin, the frontal section of the roof frame, the B posts, the lower beams (inner sills) and parts of the floorpan. They account for 20 % of the body structure. So-called "tailored rolled blanks" are used for many hot-formed body components in the Audi Q5. The semi-finished products are rolled so that they are of different thickness, giving a weight advantage of 4.6 kg. Audi uses partial tempering for the B-posts: The individual zones in the mould are cooled at different rates, giving them different strength characteristics. In a side-on impact the bottom section of the B-post deforms in order to absorb energy. On the other hand, hardly any deformation takes place in the upper section of the B-post (at head height).657_159 9 BackForward Ξ ContentsAttachmentsDoor handleThe body of the Audi Q5 (type FY) has many of the features previously associated with the Audi A4 (type 8W) and Audi A5 (type F5). The Audi Q5 also adopts, among other things, the door handle design of the Audi A4 featuring the kinematic mechanism which allows the door handle to swivel upwards when the door is opened. When compared to the previous Audi Q5 (type 8R), the design, and therefore also the procedure for removing and dismantling the door handles, has changed accordingly.Support arm Exterior door handle lightSupportsLocking cylinder (driver's door only)657_022Housing (not driver's door)Securing screwsDoor handleExterior door handle contact sensor (with advanced key only)Door handle trimDiffusing lens for exterior door handle lightCap for concealed locking cylinder (in certain countries)Note For details of the procedure for removing and dismantling the door handles, please refer to the current service literature.10 BackForward Ξ ContentsBonnetIn keeping with the current design language, and to meet the highest demands in terms of pedestrian safety, the Audi Q5 has a wrap-around bonnet. The resulting shut line between the bonnet and the front wing is the starting point of the tornado line on the Audi Q5. A high-quality car body is characterised, among other things, by absolutely uniform shut lines or gaps, which can be adjusted in several ways. These adjustment options allow service personnel to align the bonnet in the x, y and z directions after accident repairs have been carried out. The longitudinal adjustment (x axis) and the lateral adjustment (y axis) are made at the bonnet attachment points (hinges). For vertical adjustment (z direction) and further longitudinal adjustment of the bonnet, each complete hinge can be moved upwards, downwards, forwards or backwards. The attachment points are partially concealed by the hinge when the bonnet is open and, therefore, it is recommended that the hinge be tack-welded beforehand in the foremost and uppermost positions, i.e. at the greatest possible distance to the door and to the front wing.657_026Bonnet attachment points at the hingeHinge attachment at the wing stayNote For further information and details of the bonnet setting procedure, please refer to the current service literature.11 BackForward Ξ ContentsGlazingWindscreen The Audi Q5 comes with green-tinted heat insulating glass as standard. In this version the windscreen is made of laminated safety glass (VSG) with three sound-insulating interlayers, while the door windows, side windows and rear window are made of tempered safety glass (ESG). The following optional equipment is available in certain countries: • Acoustic glass in the front door windows (VSG) • Privacy glass from the B post back • Heated windscreen The heated windscreen is available in two country spec versions: • As a filament heating system with two heating fields and an invisible infrared-reflective coating for protection against excessive heating of the cabin in the summer. • As a climate comfort windscreen with no additional heating filaments. In this version the windscreen is heated by applying an electric current directly to the invisible infraredreflective coating.Version with climate comfortVersion with filament heaterOuter pane Outer pane Acoustic film Heated filament layerAcoustic filmInner pane with infrared-reflective coatingInner pane with infrared-reflective and heatable coating657_02312 BackFront side windows The front doors can be fitted with either tempered safety glass windows or, if the car is fitted with the optional acoustic glass, laminated safety glass windows. The front door windows are held in place in the window lifters by two drivers which engage two holes in the glass pane.Forward Ξ ContentsOn models fitted with tempered safety glass, there are holes in the actual glass pane. The laminated safety glass window is bonded to two adaptors which provide the holes for the drivers in the window lifter. This solution was adopted so as to avoid perforating the polymer interlayers in the laminated safety glass.Tempered safety glass657_024Laminated safety glass657_02513 BackPanoramic glass sunroof The Audi Q5 is optionally available with a panoramic glass sunroof. As is the case with the Audi Q5 (type 8R), the panoramic glass sunroof of the new Audi Q5 (type FY) has a two-part design. The front glass panel is movable and can be tilted or retracted electrically. The rear glass panel is non-movable.Forward Ξ ContentsA power-operated roller blind for both glass panels provides sun-shading, if needed. A total of four hoses provide for reliable drainage of rainwater which may have collected in the sliding sunroof frame.Drainage hose657_028Dash panelEven if they may at first glance look to be physically separate from one another, the centre and side air outlets on the front passenger side form a unit, which is attached to the dash panel by eight screws in total. The trim covering these screws and the smaller driver's side trim panel is attached using a new concept. The trims are held in place, without additional screws, by means of so-called "crash hooks", which ensure that they cannot become randomly detached during an accident. This, in turn, means that allowance has to be made for additional lateral displacement of the trims during installation and removal.212 1657_027Crash hookCrash hook14 BackForward Ξ ContentsSeating systemsThe seats in the new Audi Q5 have been radically redesigned under the premise of strict lightweight design. High-strength steels are used in the underbody area to reduce weight, while magnesium components and a lightweight wire frame are used in the rear bench seat. Depending on trim level, the rear bench seat backrest can be remotely released and folded down. When the remote release lever in the luggage compartment is activated, pawls are actuated via Bowden cables, thereby relieving the load on the springs. The rear backrests fold forward down onto the seat cushions automatically. When the remote release is activated with the backrests folded down, the backrests are automatically raised about 45° by the springs.Remote release leverDeflection mechanism for pawl657_029Torsion springBowden cable15 BackForward Ξ ContentsEnginesPetrol enginesTorque/power curve of 2.0l TFSI engine2.0l engine with engine code DAXB Power output in kW Torque in NmTorque/power curve of 3.0l TFSI engine3.0l engine with engine code CWGD Power output in kW Torque in NmEngine speed [rpm]657_031Engine speed [rpm]657_032Features Engine code Type Displacement in cm Stroke in mm Bore in mm Number of valves per cylinder Compression ratio Power output in kW at rpm Torque in Nm at rpm Engine management Exhaust gas treatment Emission standard Fuel type3Specifications DAXB 4-cylinder inline engine 1984 92.8 82.5 4 9.6 : 1 185 at 5000 - 6000 370 at 1600 - 4500 SIMOS 18.41 Close-coupled ceramic catalytic converter, 2 oxygen sensors EU 6+/LEV 3/Tier 3 95 RON CWGD V6-cylinder engine 2995 89.0 84.5 4 11.2 : 1 260 at 5400 - 6400 500 at 1370 - 4500 Bosch MDG 1 2-stage ceramic catalytic converter, 2 oxygen sensors EU 6+/LEV 3/Tier 3 98 RONReference For further information about the 2.0l TFSI engine and the 3.0l TFSI engine, please refer to Self Study Programme 645 "Audi 2.0l TFSI engines of EA888 series" and Self Study Programme 655 "Audi 3.0l V6 TFSI engine of EA839 series".16 BackForward Ξ ContentsDiesel enginesTorque/power curves of 2.0l TDI engine2.0l engine with engine code DEUA Power output in kW Torque in Nm 2.0l engine with engine code DETA Power output in kW Torque in NmEngine speed [rpm]657_013Engine speed [rpm]657_107Features Engine code Type Displacement in cm3 Stroke in mm Bore in mm Number of valves per cylinder Compression ratio Power output in kW at rpm Torque in Nm at rpm Engine management Maximum injection pressure in bar Exhaust gas treatment Emission standardSpecifications DEUA 4-cylinder inline engine 1968 95.5 81.0 4 16.2 : 1 110 at 3250 - 4200 320 at 1500 - 3250 Bosch EDC 17 2000 with solenoid injectors, 8-port nozzles Oxidising catalyst, SCR-coated diesel particulate filter, oxygen sensors EU 6 (W) EU 6 (W) DETA 4-cylinder inline engine 1968 95.5 81.0 4 15.5 : 1 140 at 3800 - 4200 400 at 1750 - 3000 Bosch EDC 17Reference For further information about the 2.0l TDI engine, please refer to Self Study Programme 608 "Audi 1.6l / 2.0l 4-cylinder TDI engines".17 BackForward Ξ ContentsSCR systemReducing agent tank The reducing agent tank is an injection moulding made from two halves, and not an extruded tank. This has the advantage of reducing weight. Thus, allowance could be made in the vehicle design for the integration of baffles and a cabin-adapted heating system as installation space. The SCR system has two different tanks for AdBlue® reducing agent: a tank with a capacity of 12 litres and an optional tank for extended range with a capacity of 24 litres (see figure below). The 12-litre reducing agent tanks is distinguished by a lower filler tube and a lower vent line. The 24-litre tank has a shorter filler tube and vent line. A non-return flap (spitback flap) at the end the vent tube holds back rising reducing agent during filling and allows displaced air to flow from the tank to the vent. This prevents overfilling of the tank and discharge of reducing agent at the filler neck.Sealing capReducing agent filler neckDelivery module in reducing agent tank The delivery module (delivery unit for reducing agent GX19) is, like the SCR systems in other Audi models, welded to the reducing agent tank. However, parts of the delivery module can be replacedReducing agent tank base Electrical connection for the tank heater Electrical connections for the delivery module (sensors, delivery module heater, pump) Outlet for draining the reducing agent tankvia a bolted service cover on the underside of the tank.Delivry module (metering system delivery unit for reducing agent GX19)Fixed tank bracket for attaching the reducing agent tank to the underbody Service cover on the delivery module Reducing agent line connection (exchangeable)657_00418 BackEqualisation chamber at filler neck The ventilation system within the reducing agent tank is designed so that the tank can be filled with AdBlue® reducing agent using a pump nozzle. An equalisation chamber at the filler neck allows the inflow of reducing agent at a high flow rates of up to 40 litres per minute. Splashing reducing agent would cause the pump nozzle to shut off, so the reducing agent is held back in this equalisation chamber and allowed to settle.Forward Ξ ContentsOverflow during fillingVentNon-return flapEqualisation tank in filler neckReducing agent tank heater Z102Reducing agent tankMetering system delivery unit for reducing agent GX19 with: • Heater • Reducing agent quality sensor G697 • Delivery unit with reducing agent pump V437 • FilterHeat shield657_003 19 BackDelivery module components • Heater • Ultrasound sensor for measuring reducing agent level and quality • Orbital pump for pumping reducing agent to the injectorForward Ξ Contents• Pressure sensor to control operating pressure/ pressure accumulator to level off pressure peaks • Delivery module filterPressure sensor and pressure accumulatorPressure sensorSensor unit The sensor unit comprises the following sensors: • Reducing agent quality sensor G849 • Reducing agent tank sender G684 • Reducing agent temperature sender G685Acoustic tube with mirrorsUltrasound cone for detecting a full tank (direct piezo sensor)Measurement zone of reducing agent quality sensor 849 (combined piezo sensor) Reducing agent temperature sensor G685 Reducing agent tank sensor G684 for low levels (combined piezo sensor)Ultrasound sensors • The direct piezo sensor (centre) is used for high reducing agent levels. • The combined piezo sensor on the left is used for low reducing agent levels. When the level reaches the uppermost mirror in the riser tube, this sensor automatically activates the electronics. • Two defined measurement zones are used to determine the travel time of the sound waves and hence the quality (density) of the reducing agent.20 BackReducing agent pump The reducing agent pump V437 is of an orbital-type pump similar to a peristaltic pump, where the fluid contained within a flexible tube is displaced by a cam. The cam pinches the diaphragm as it rotates, thus forcing the fluid to be pumped through the tube.Delivery module Tank filterForward Ξ ContentsHeaterPressure sensor Screen filterPressure connection Suction connection Reducing agent pump V437 Heater Pressure accumulatorPressure connectionSuction connectionReducing agent injector N474657_007657_114Filter • The surface of the filter also serves as a reservoir, ensuring a steady supply of reducing agent to the pump even at low reducing agent levels.Cam • The reducing agent is displaced through a flexible tube by a cam and pumped under pressure into the pressure accumulator before entering the SCR line to the reducing agent injector.Delivery module heater• Consists of three PTC heating elements • To improve heat distribution, the PTC heating elements are attached to a thermally conductive frame integrated in the delivery module housing.657_006 21 BackForward Ξ ContentsEngine/gearbox combinationsThe engine-gearbox combinations shown below are those currently available at market launch. Petrol engines 2.0l TFSI engine (DAXB) 3.0l TFSI engine1) (CWGD)7-speed Dual clutch gearbox 0CJ S tronic DL382-7A • All-wheel drive1) 8-speed automatic gearbox 0D5 tiptronic AL552-8Q • All-wheel drive1) Rear axle drive 0D0 HL165.U1 MRear axle drive 0D2 Standard differential – HL195.S2 M1) Rear axle drive 0D3 Sport differential – HL195.T2 M1) (optional)1)To be introduced after market launchKey to manufacturer code designation e.g.: ML322-6F A M D L Automatic planetary gearbox Manual gearbox Dual-clutch gearbox Longitudinal mounting 6 F Q Number of gears Front-wheel drive All-wheel-drive system with integrated transfer case/centre differential – quattro with self-locking centre differential All-wheel-drive system with separate transfer case/centre differential, e. g. – quattro with ultra technology322 Development number (indicating torque capacity, generation and position of front final drive etc.)A 22 BackForward Ξ ContentsDiesel engines2.0l TDI engine (DEUA)2.0l TDI engine (DETA)6-speed manual gearbox 0DJ ML322-6F • Front wheel drive1)6-speed Manual gearbox 0CX ML402-6F • All-wheel drive1)7-speed Dual clutch gearbox 0CJ S tronic DL382-7A • All-wheel drive1) Rear axle drive 0D0 HL165.U1 M1)To be introduced after market launchNew final drive designationPreviously Rear axle drive 02D Rear axle drive 0D3 Rear axle drive 0B0 HL600 B HL601 B – New HL195.S2 M HL195.T2 M HL165.U1 M 2nd gen. standard 2nd gen. sport differential quattro ultraKey to new manufacturer code designationHL165.U1 MrearlongitudinalCrown gear diameter in mmU = ultra Technologie S = Standard (unlocked differential) T = Torque Vectoring (sport differential)1st generation 2nd generationManufacturer code: Magna powertrain23 BackForward Ξ ContentsPower transmissionOverviewIn terms of its power transmission system the Audi Q5 (type FY) has much in common with the Audi A4 (type 8W) and A5 (type F5). For more information about this, please refer to SSP 644 (chapter on Power transmission) and the Audi Service TV programmes at www.Audi-Training-Online.com. Refer to page 47. Here you can find information about modifications and new features of the power transmission system in the Audi Q5 (type FY) which were previously introduced in the Audi A4 (type 8W) and A5 (type F5). The notes explain where you can find the relevant information. The Audi Q5 will initially be available with S tronic and as a quattro with ultra technology. Further gearboxes and drive variants will be added successively to the line-up. Refer to the tables on the right. Depending on engine type and the customer's specifications, the following all-wheel-drive concepts will be available in future: • quattro with ultra technology • quattro with self-locking centre differential • quattro with sport differentialCable 1 7-speed dual clutch gearbox 0CJ • with all-wheel-drive clutch 0CJAcuator unit for Parking lock emergency releaseCable 2Quick-release coupling657_064Parking lock emergency releaseThe emergency release cable is made up of two sections. In the area of selector mechanism there is a quick-release coupling which interconnects both cable pulls. The actuating unit is located under the carpet on the driver's side. The system has the same operating principle as that in the Audi A4 (Typ 8W). For information on operation, please refer to SSP 644 and watch the Audi Service TV programme – STV_0411_Emergency releasing the parking lock in the Audi A4 (type 8W).657_065 24 BackForward Ξ ContentsOverview of manual and automatic gearboxesDepending on engine type, the following gearboxes will be available initially: PR no. G0K G0L G1D G1G Manufacturer code designation ML322-6F ML402-6A DL382-7A AL552-8Q Service code designation 6-speed manual gearbox 0DJ with ESS1) 6-speed manual gearbox 0CX with ESS1) 7-speed dual clutch gearbox 0CJ 8-speed automatic gearbox 0D5 Marketing code designation – – S tronic tiptronic Drive concept Front wheel drive quattro with ultra technology quattro with ultra technology • quattro with self-locking centre differential • quattro with sport differential (optional)1)ESS = injection lubrication systemRear axle differential overviewDepending on the quattro concept and the customer's specifications, the following rear axle differentials will be available: PR no. GH1 GH2 GH4 Manufacturer code designation HL195.S2 M HL195.T2 M HL165.U1 M Service code designation Rear axle drive 02D Rear axle drive 0D3 Rear axle drive 0B0 Combination with gearbox 0D5 0D5 0CJ/0CX quattro concept quattro with self-locking centre differential quattro with sport differential (optional) quattro with ultra technologySelector mechanism featuring shift-by-wire technology • For information about this system and the operating concept, please refer to SSP 644.The figure shows the driveline with 7-speed dual clutch gearbox 0CJ and the quattro drive with ultra technology.A new feature is the all-wheel drive system – quattro with ultra technology – was initially used in the Audi A4 allroad in mid 2016.Rear axle drive 0B0 • with dog clutch, see page 30.657_063 25 BackForward Ξ Contentsquattro with ultra technologySystem descriptionquattro stands for outstanding traction, driving dynamics and safety. The new ultra technology adds to these typical characteristics of the quattro the attribute of efficiency. The quattro drive with ultra technology is a full-time all-wheeldrive system with active rear axle torque vectoring. The electronic differential lock (EDS) integrated in the ESC control unit (for all driven wheels) and wheel-selective torque control 1) provide enhanced traction and driving dynamics. The system includes an electronically controlled all-wheel-drive clutch, the all-wheel-drive control unit with clutch actuator and a dog clutch with actuator integrated in the rear axle drive. The special feature of the quattro drive mit ultra technology is the ingenious interaction between the all-wheel-drive clutch and the dog clutch in the rear axle drive. To reduce drag losses, the prop shaft and sections of the rear axle drive can be deactivated by opening these two clutches. This in turn offers significant fuel savings and reduces CO2 emissions. An intelligent all-wheel drive control strategy in the all-wheel-drive control unit continuously computes the driving status of the vehicle and situatively distributes drive torque to the rear axle. To facilitate this calculation, the all-wheel-drive control unit is networked with a multiplicity of other control units by FlexRay bus. On the basis of this information, the control unit records and evaluates all data relevant to the driving status of the vehicle at 10 ms intervals. If the control unit detects a driving situation in which all-wheel drive is not required and therefore offers no advantages, it changes over to front-wheel drive. If the control unit detects a driving situation in which all-wheel drive is an advantage, the rear axle is activated within approximately 200 ms and provided with sufficient drive torque. The control strategy is so intelligent that, in most cases, it computes torque requirements approximately 500 ms in advance. This means that the all-wheel drive is activated even before it is needed.1) or information about wheel-selective torque control, please refer to F SSP 617 "Audi RS 5 ’10 and RS 4 Avant ’13 Power Transmission".Rear axle drive 0B0Dog clutch657_067 26 BackForward Ξ ContentsDriveline mit 2.0l TFSI engine7-speed dual clutch gearbox 0CJ • with all-wheel-drive clutch 0CJ657_066All-wheel-drive control unit J492All-wheel-drive clutch 0CJ657_068 27 BackForward Ξ ContentsSystem components All-wheel-drive clutchThe all-wheel-drive clutch is flanged-mounted to the gearbox. Refer to pages 38 and 45. It forms a fully integrated unit together with the following components: • All-wheel drive control unit J492 • All-wheel-drive clutch actuator V622 • All-wheel-drive clutch position sensor G969 There are two types of clutch with different maximum torque levels: • All-wheel-drive clutch 0CJ with 800 Nm max. torque Manufacturer code designation: VTK080 • All-wheel-drive clutch 0CX with 1,200 Nm max. torque Manufacturer code designation: VTK120 Both variants differ in terms of the number of clutch plates and in the way the front clutch housing is adapted to the higher clutch torque.Clutch output shaft • Gearbox output shaft657_069All-wheel-drive control unit J492ATF filler and inspection screw657_070Clutch engagementOil drain screwClutch output shaft • Gearbox output shaftMulti-plate clutchClutch input shaftAll-wheel-drive clutch actuator V622 All-wheel-drive clutch position sensor G96928657_071 BackForward Ξ ContentsLubrication/cooling oil supplyThe all-wheel drive has an oil supply for lubrication and cooling of the clutch plates. The oil supply is subdivided into two oil chambers: A and B. A special control mechanism with oil metering slot ensures, firstly, that the clutch is lubricated and cooled when all-wheel drive is active and, secondly, that the oil level in oil chamber B is reduced to such an extent that churning losses are kept to a minimum.Oil chamber A All-wheel drive Oil chamber AThis is how it works: The outer plate carrier is driven continously during vehicle operation. The oil is centrifuged into an oil trap and ducted into oil chamber A.657_072Oil chamber B Outer plate carrier Oil metering slot – openAll-wheel drive When the clutch is operated, the oil metering slot also opens automatically, and the clutch is supplied with oil from oil chamber A. The clutch plates are lubricated with ATF from the inside out, and the oil flows into oil chamber B. From here, the ATF is recirculated to clutch chamber A as described previously, thereby circulating the oil.Front wheel driveFront wheel drive When front wheel drive is active, the clutch is always open. In this clutch position the oil metering slot is closed and oil circulation between oil chambers A and B is interrupted. The oil is now pumped from the outer plate carrier as far as possible into oil chamber A.657_073Refilling the ATF / checking the oil level1)Oil metering slot – closedThe ATF filler and check screw reaches into oil chamber A. The oil level is correct when the oil level in oil chambers A and B at the bottom edge of the filler and check screw. As described previously, the oil level in the oil chambers can vary considerably. It is therefore important to equalise the levels in both oil chambers when filling the ATF system and before checking the oil level. To equalise these levels, the oil drain screw housing is designed so that the desired level-equalising effect can be achieved by slackening the oil drain screw 4-5 turns. All-wheel-drive clutches 0CJ and 0CX are filled with lifetime oil and need no routine maintenance. If the ATF needs to be replaced, e.g. due to repair work, the programmed values for oil deterioration have to be reset. Refer to the workshop manual and the diagnostic tester.Very different oil levels in oil chambers A and B1) efer to the special procedure for filling the ATF system and checking for R correct oil level in the workshop manual.The level in oil chambers A and B is equalised by slackening the oil drain screw657_074 29 BackForward Ξ ContentsRear axle drive 0B0A special efature of the quattro with ultra technology is the dog clutch in the rear axle drive. When the all-wheel-drive clutch is open, the dog clutch allows the crownwheel/differential gear and the prop shaft to be disengaged from the remainder of the driveline. As the crownwheel/differential gear and the prop shaft generate the greatest drag torque in front-wheel-drive mode, disengaging these elements provides significant fuel savings compared with the previous all-wheel-drive systems. During internal test drives, average fuel saving of approximately 0.3 litres per 100 km compared to similar vehicles without disengagement of the crownwheel/differential gear and the prop shaft.Axle shaftDifferential bevel gear Axle bevel gear Sender wheel for G970Dog clutchAll-wheel-drive clutch actuator 2 V623Prop shaft speed sensor G970657_075Actuating dogWorm shaftInner drive shaftAxle shaft30657_076 BackForward Ξ ContentsDog clutchThe right-hand flange shaft consists of three shafts (axle shaft, worm shaft and flange shaft). The axle shaft is connected to the right-hand axle bevel gear in the differential and mounted in the worm shaft at the other end. The worm shaft interlocks with the flange shaft. The axle shaft and the worm shaft can be engaged or disengaged by a dog clutch. Refer to Fig. 657_076. The dog clutch is opened or closed by means of a sophisticated and highly efficient electromechanical clutch control system.Dog clutch with clutch actuatorSpringDog clutch – closed When the clutch actuator V623 is inactive (not energised), the dog clutch is closed. Two powerful springs1) close the dog clutch or keep the dog clutch closed. When the dog clutch is closed, drive is transmitted from the axle shaft to the flange shaft.Worm shaft All-wheel-drive clutch actuator 2 V623657_077Dog clutch – opening – open holdActuating dogAWhen clutch actuator 2 V623 is energised, it pushes the disengagement lever into the worm gear spline, thereby actuating the disengagement mechanism. The rotational movement of the worm shaft produces axial lift at the disengagement lever, which pushes the actuating dog out of the spline against the pressure of the spring and opens the dog clutch.ABThe dog clutch is fully open after approximately four turns. The disengagemernt mechanism pushes the disengagement lever automatically out of the worm gearing and locks the disengagement lever in this position. The disengagement lever stays locked as long as the clutch actuator 2 V623 is activated by a low holding current.Release lever657_078When the dog clutch is opened, the crown wheel and the drive pinion are disconnected from the flange shafts. Refer to page 34, Fig. 657_103.Dog clutch – closing Before the dog clutch is closed, the speed differential is reduced via the controlled all-wheel-drive clutch. To close the dog clutch, clutch actuator 2 V623 is deactivated. The disengagement lever is retracted, releasing the disengagement mechanism. The actuating dog is now pushed into the spline at lightning speed by the spring forces 1), and the dog clutch is closed. Refer to page 32, Fig. 657_096.BDisengagement lever locked • Lock1) nly one spring is visible (the second spring is concealed beneath the first O one).657_079 31 BackForward Ξ ContentsChanging from all-wheel drive to front-wheel driveDriving with all-wheel drive In all-wheel drive mode, the dog clutch in the rear axle drive is closed and the all-wheel-drive clutch transmits the drive torque computed by the all-wheel-drive control unit to the rear axle via the prop shaft.657_094657_095All-wheel-drive clutch – active • Fully variable torque distribution by the allwheel-drive clutch. • The optimal power split between the front and rear axles is computed and adjusted on an ongoing basis. Refer to page 36.Dog clutch – closed Refer to description on page 31.Colour key: Parts in action Parts which do not contribute to power flow Rotating parts which do not contribute to power flow Parts which are stationary Torque, drive troque, forces All-wheel-drive clutch actuator 2 V623657_09632 BackSwitching off and disconnecting all-wheel drive If the system detects a driving situation in which all-wheel drive offers no advantages and is not expected to be needed shortly, it changes over to front-wheel drive for efficiency.Forward Ξ Contents657_097Dog clutch – opening – A657_098All-wheel-drive clutch – opening Initially, the all-wheel-drive clutch is opened and the handling in front-wheel-drive mode is evaluated. If no change in handling is detected, the dog clutch in the rear axle drive is opened.Dog clutch – openingAAll-wheel-drive clutch actuator 2 657_099 V623 – active – defined electrical current applied Dog clutch – opening – A Actuating dogTo open the dog clutch, a specific electric current is applied to clutch actuator 2 V623. The lutch actuator 2 V623 now pushes the disengagement lever into the worm gear spline, actuating the disengagement mechanism. Due to the rotational movement of the flange and worm shaft, the disengagement mechanism now displaces the actuating dog against the force of the spring and opens the clutch. Refer to page 31.BWorm shaftInner drive shaftSpring There are two springs, one beneath the other.Release lever657_100 33 BackAll-wheel drive disconnected – front-wheel drive In front wheel drive mode, the all-wheel-drive clutch and the dog clutch are open and the prop shaft, the crown gear and the pinion are disconnected. Rendering these components stationary reduces drag loses to a large extent and saves fuel.Forward Ξ Contents657_101Dog clutch – open – C Axle shaft657_102Differential bevel gearClutch actuator for all-wheel drive V662All-wheel-drive clutch – open To minimise drag losses in the all-wheeldrive clutch when front-wheel drive is active, special clutch plate separation measures and a generous clearance ensure that there is little friction loss between the clutch plates. Moreover, the ATF is also kept away from the rotating parts in order to reduce churning losses. Refer to page 29.657_103All-wheel-drive clutch actuator 2 V623 – active – activated with low holding currentDog clutch The dog clutch is fully open after approximately four turns. The disengagemernt mechanism pushes the disengagement lever automatically out of the worm gearing and locks the disengagement lever in this position. A reduced holding current at the clutch actuator 2 V623 is sufficient to maintain this functional position.Colour key: Parts in action Parts which do not contribute to power flow Rotating parts which do not contribute to power flow Parts which are stationary Torque, drive troque, forces34 BackForward Ξ ContentsChanging from front-wheel drive to all-wheel driveActivation of all-wheel drive To activate the all-wheel drive, the dog clutch must be closed again. To this end, the prop shaft and the crown gear must be accelerated to a near-synchronous speed by closing the all-wheeldrive clutch to the required degree. The prop shaft speed sensor G970 and the wheel speed sensor supply the required speed information.657_104657_105All-wheel-drive clutch – active • Prop shaft accelerationProp shaft speed sensor G970657_106All-wheel-drive clutch actuator 2 V623Clutch actuator 2 V623 is deactivated shortly before synchronous speed is reached, with the result that the disengagement lever is retracted and the disengagement mechanism is unlocked. The actuating dog is now pushed into the spline at lightning speed by the spring forces, and the dog clutch is closed.Driving with all-wheel drive When the dog clutch closes, the clutch torque computed by the all-wheel-drive clutch is transmitted. Refer to the illustrations and texts on page 31.35 BackForward Ξ ContentsAll-wheel-drive strategyA highly intelligent all-wheel-drive control strategy is implemented in the all-wheel-drive control unit J492. This control strategy utilises a large volume of data and information which is acquired and evaluated at 10 ms intervals. For this purpose, the control unit is networked with the control units shown in Fig. 657_038 by FlexRay data bus. The objective of the control strategy is to activate all-wheel drive before it is actually needed, and it does this by employing a predictive strategy. This is made possible by acquisition and evaluation of the driving status parameters and influencing factors shown on the right. Predictive analysis of the need for all-wheel drive The traction limits of the wheels are determined up to 500 ms in advance by evaluating the driving status parameters shown adjacent. The need for all-wheel drive is determined on the basis of this information, and the lead time is sufficient to activate the allwheel drive before the wheels reach their traction limits.Operating unit 1 for drive and comfort/convenience functions E791 • Audi drive select buttonSteering column electronics control unit J527Engine control unit J623ABS control unit J104Factors influencing the need for all-wheel drive The activation and utilisation ratio of all-wheel drive are influenced by specific factors. Driver type – The utilisation ratio of all-wheel drive and frontwheel drive is essentially dependent on driving style (sporty or economical). Audi drive select – in dynamic mode the vehicle always starts off in all-wheel drive. The all-wheel-drive activation theshold is lower than in other drive select modes and the vehicle is held in allwheel-drive for longer. All-wheel drive is always active in allroad and lift/offroad modes. ESC status – All-wheel drive is always active in offroad mode and in ESC-OFF mode. Trailer operation – When towing a trailer, all-wheel drive is always used at drive-away and stays engaged at low speeds. Ambient temperature/friction coefficient – All-wheel drive is always active when driving at low speed at low ambient temperatures and on surfaces with a low friction coefficient.Mechatronic module J743 and Automatic gearbox control unit J217 All-wheel-drive control unit J492Reactive activation of all-wheel drive In reactive activation mode (which rarely occurs in practice), the system reacts to sudden unforeseeable changes in the friction coefficient of the road surface. An example would be the front wheels going from dry asphalt to a sheet of ice. In these situations the system detects a sudden change in friction coefficient on the basis of wheel speed differences. The all-wheel drive system is activated at lightning speed and, working in conjunction with the suspension control systems, provides safe handling, excellent traction and driving dynamics - even in situations such as this.36 BackDriving status parameters for determining the need for all-wheel driveForward Ξ ContentsEngine speedAccelerator/ brake pedal travelSteering angleDriveline modelDriving speedLateral/longitudinal accelerationWheel load modelFriction coefficient recognitionFactors influencing the need for all-wheel driveSuspension control unit J775Driver type Data bus diagnostic interface J533Audi drive selectTrailerAmbient temperature657_038Basic system reactions • The all-wheel-drive clutch is opened when braking is applied. The all-wheel-drive utilisation ratio is generally lower: • On motorways and dual carriageways. • When driving straight ahead or at a constant high speed. The all-wheel-drive utilisation ratio is generally higher: • At low road surface friction coefficients (in winter and in wet conditions). • At low and medium driving speeds with acceleration phases. All-wheel-drive generally stays active: • When the vehicle is being driven in a dynamic fashion on winding roads, even if the asphalt is dry and grippy. Key: Convenience CAN FlexRay37Trailer recognition control unit J345 BackForward Ξ Contents7-speed dual clutch gearbox 0CJThe 0CJ gearbox is a further variant of the DL382 gearbox series1). Apart from the components for all-wheel drive, it is identical to 7-speed dual clutch gearbox 0CK with shift-by-wire. For more information, please refer to SSP 644 and the Audi Service TV programmes previously released for the DL382 series. Refer to page 47.7-speed dual clutch gearbox 0CJAll-wheel-drive clutch 0CJ657_039ATF drain screw ATF filler and inspection screw1)All-wheel-drive control unit J492The DL382-7x gearbox series currently comprises the following gearbox variants:Input shaft 1DL382-7F – 7-speed dual clutch gearbox 0CK2) DL382-7Q – 7-speed dual clutch gearbox 0CL3) DL382-7A – 7-speed dual clutch gearbox 0CJ3) A key to the code dsignations can be found on page 25.2) 3)This variant is available with and without shift-by-wire. This variant is exclusively available with shift-by-wire.All-wheel-drive clutch 0CJ • Refer to page 28. All-wheel-drive clutch ventThe output shaft (subgearbox 1/2) transmits drive torque equally to the spur gear step for the front axle drive and to the all-wheel-drive clutch. ATF drain screw – all-wheel-drive clutch38 BackAll-wheel-drive clutch 0CJ is self-contained unit flange-mounted to the 0CJ gearbox. 0CJ gearbox is always supplied as an Audi original part without an all-wheel-drive clutch. Gearbox oil systemsForward Ξ ContentsThe 0CJ gearbox has two oil systems: an ATF system for the dual clutch and the electrohydraulic control unit, and an MTF system for the gear set and the front axle drive (such as the 0CK gearbox). The ATF must be changed at specified intervals, but the MTF is designed to provide lubrication for the lifetime of the gearbox and does not require servicing. All-wheel-drive clutch 0CJ has its own ATF supply which is designed to provide lubrication for the lifetime of the gearbox and does not require servicing.Clutch K1Gear shift lever for parking lock emergency release Parking lock module Selector shaft for parking lockDual mass flywheel with pendulum-type absorber • Refer to Audi Service TV programme information on page 47.Clutch K2Input shaft 2657_040Parking lock gearPressure accumulator (gas-pressure hydraulic accumulator) Follow the safety instructions given in the workshop manual.MTF filler and inspection screwKey: Gearbox input, sub-gearbox 1 Gearbox input, sub-gearbox 239 BackForward Ξ Contents6-speed manual gearbox with oil injection lubricationThe manual gearboxes in the Audi Q5 (type FY) originate from the latest gearbox series (MLxx2-6x1)) and are pre-installed in the Audi A4 (type 8W) and Audi A6 (type 4G) series. Even during the market launch, the manual gearboxes were noted for their very high efficiency. Since production week 34/2016 these gearboxes have been equipped with an oil injection lubrication system. By eliminating churning losses the oil injection lubrication system provides a significant increase in efficiency.6-speed manual gearbox 0DJ Gearbox breatherClutch module with dual mass flywheel with pendulum-type absorber • Refer to SSP 644657_042Output shaft • Oil pump drive657_043Oil pumpInput shaft (main shaft)Supply to oil rail 2Pump pinion • Oil pump drivePressure test connection for function-testing by manufacturer Sealing screw Suction port657_0441)Refer to page 45.Supply to oil rail 140 BackDirection of travelForward Ξ ContentsThe figure shows the 6-speed manual gearbox 0CX and oil injection lubrication at standstill.Oil pan657_045Oil pumpOil pan • The oil level is below that of the gear set.Filler and inspection screwOil rail 1System description The oil injection lubrication system is an all-mechanical system. The oil pump is driven by the gearbox output shaft via a spline (Torx). The gearbox output shaft only rotates when the vehicle is moving. This means that no oil is pumped when the vehicle is at a standstill. When the vehicle begins to move, the oil pump conveys oil into the two oil rails and into the hollow-drilled gearbox output shaft The oil rails are fitted with injectors which inject the lubrication and cooling oil directly into the meshing zone of the spur gears and the crownwheel/differential gear. A small portion of the pressurised oil is channeled directly into the hollow-drilled gearbox output shaft through bores in the oil pump output shaft and in the pump pinion, where transverse ports allow the oil to flow to the gear pinion bearings. The gear pinion bearings on the output shaft are also lubricated from the inside via transverse ports. Oil is supplied from the oil pan in the rear gearbox housing. To this end, the oil pan collects splash oil, which is channeled to the rear main shaft bearing and into the hollow-drilled input shaft.Oil panInput shaft with pump pinion Direction of travelOil pumpOil rail 2657_046Oil rail 1InjectorOil filter with intake manifoldGuard plate with flap41 BackForward Ξ ContentsOil injection lubrication during vehicle operation During vehicle operation, the oil pump supplies the two oil rails and the output shaft with oil. The system is designed to ensure that the lubrication points are supplied with sufficient oil even when travelling at low speeds.Front view657_047Oil rail 1Filler and inspection port Oil level at standstill The oil level varies according to driving speed (pump output). Oil rail 2657_048High transverse acceleration – left-hand curve The gearbox geometry is such that when negotiating a left-hand curve at a high rate of transverse acceleration the oil can shift to the right, with the result that the oil pump is unable to take in sufficient oil. In this situation the guard plate and the flap ensure that the oil is held back and that sufficient oil is retained in the oil pan. The flaps acts as a non-return valve and prevents the oil from shifting to the left. When driving straight ahead, the flap is down allowing the oil to flow unobstructed from one side of the oil pan to the other. This ensures that the oil pump has a steady supply of oil at all times.657_049control flap42Shield BackOil pump The oil pump is designed such that it conveys oil both when driving forward and in reverse. To enable the pump to deliver oil when rotating both clockwise and anticlockwise, the pump has two side intake points and two pressure chambers (A and B). Pressure chambers A and B flow into the common pressure chamber C to which the two oil rails are connected and supplied with oil. A non-return valve at the outlets of pressure chambers A and B opens or closes the inlet to pressure chamber C depending on the direction in which the oil pump is rotating. The two non-return valves allow the oil pump to take in oil and build up pressure correctly and thus prevent the oil rails and the pump from running empty when the vehicle is at a standstill. They allow the rapid build-up of pressure and ensure that lubrication is provided at driveaway.Input shaftForward Ξ ContentsPressure chamber ASide intake point657_050Side intake point Non-return valve B Non-return valve A Common pressure chamber C Pressure chamber BPressure chamber CPressure connection to oil rail 2Oil supply – driving forwards The gears take in the oil at the side and force it into pressure chamber A. The oil flows via non-return valve A into oil chamber C, to which both oil rails are connected. Non-return valve B is closed and allows the pump to take in oil via both side intake points. Oil supply to gearbox output shaft657_051The oil pump input shaft and the pump pinion are hollow-drilled. A small portion of the pressurised oil flows into the hollow input shaft of the oil pump via a transverse bore and directly into the gearbox output shaft via the pump pinion.Pump pinion Pressure connection to oil rail 1 Suction port Pressure chamber APressure chamber CSide intake pointOil supply – reversing The gears take in the oil at the side and force it into pressure chamber B. The oil flows via non-return valve B into oil chamber C to which both oil rails are connected. Non-return valve A is closed and allows the pump to take in oil via both side intake points. The gearbox output shaft is supplied with oil as described above.657_052Side intake point Pressure chamber B43 BackOil supply All manual gearboxes in the Audi Q5 (type FY) have oil injection lubrication. The gearboxes with oil injection lubrication have a much smaller oil fill capacity than the gearboxes without oil injection lubrication and are filled up to the bottom edge of the filler and inspection screw. Refer to the workshop manual. No servicing interval applies to the gear oil and the oil filter as they are designed for the lifetime of the gearbox.Forward Ξ Contents6-speed manual gearbox 0DJAccess to pressure test connection • Not currently relevant to serviceThe gearboxes with oil injection lubrication have a pronounced recess for the oil pan657_053Filler and inspection screwOil drain screwFiller and inspection screwOil level at standstill • Fill and inspection level • The oil level is below that of the gear set. Only the spur gear step for the final drive and the crown gear are immersed in the oil.657_054Drainage outlet - drain screw • As the drain screw is relatively high up, a certain amount of oil always remains in the gearbox when draining off the oil.ShieldIntake manifold of the oil pumpcontrol flapPermanent magnet Oil filter with integrated intake manifoldand permanent magnet.Filter intake manifold657_05544 Back6-speed manual gearbox 0CX – quattro with ultra technology A manual gearbox with quattro drive (0CX gearbox) is not scheduled to be rolled out for the Audi Q5 until mid 2017. The 0CX gearbox has been available in the Audi A4 (type 8W) since around September 2016.Forward Ξ ContentsThe 0CX gearbox ... is only available with oil injection lubrication. ... ... has a maintenance-free MTF system. ... is only available in the quattro with ultra technology. ... is used currently in combination with all-wheel-drive clutch 0CX. ... is supplied as an Audi original part without all-wheel-drive clutch.657_056All-wheel-drive control unit J492Cap • For protection during transportation and handlingAll-wheel-drive clutch 0CX • Peak clutch torque: 1200 Nm • Autonomous unit with its own maintenance-free ATF system • Refer to page 28.657_0571)The MLxx2-6x gearbox series currently comprises the following gearboxes:Gear recognition sensor G604 • For information about G604, please refer to SSP 486 (page 32 ff.)ML332-6F – 6-speed manual gearbox 0DJ ML402-6F – 6-speed manual gearbox 0CS ML402-6A – 6-speed manual gearbox 0CX A key to the code dsignations can be found on page 22.The 0DJ and 0CS gearboxes were fitted without oil injection lubrication up until around September 2016 and from then onwards were only available with oil injection lubrication. The 0CX gearbox is only available with oil injection lubrication.45 BackForward Ξ Contentsquattro with self-locking centre differential/quattro with sport differentialquattro with self-locking centre differential For engines developing more than 500 Nm of torque, the 8-speed automatic gearbox 0D5 is installed in conjunction with the quattro all-wheel drive and a self-locking centre differential. This all-wheel drive can be combined with the rear axle drive 0D3 (sport differential) as an option. For information about the 0D5 gearbox, please refer to SSP 632 and SSP 644. quattro with sport differential The 0D3 sport differential is an evolutionary, second-generation unit based on 0BF sport differential. The key modifications in sport differential 0D3 are: • Adaptation of the gearcase to the rear axle • Welded crown gear and miscellaneous weight-saving measures • New axle oil and ATF • Shortened sensors for more clearance to exhaust system • Dual control unit concept in conjunction with J775 and J187 • Renaming of the sport differential control unit – previously J492, now J187 • New address code – previously 22, now 32 The basic hardware of the sport differential (torque redistribution units, hydraulic control unit, sensors and actuators) is to a large extent identical to that of the first-generation sport differential.8-speed automatic gearbox 0D5 – tiptronicThe self-locking centre differential comes in different versions (different manufacturers). The characteristi