TECHNICAL DOCUMENTATION

SSP 820173 The EA888 20L TSI Engine Gen III B

PDFEN21 pages1 MB
SSP 820173 The EA888 20L TSI Engine Gen III B - PDF cover

This PDF is currently unavailable.

Read document text
Self Study Program 820173The EA888 2.0L TSI Engine Gen III BDesign and Function - Tablet Format Volkswagen Group of America, LLC Volkswagen Academy Printed in U.S.A. Printed 6/2017 Course Number SSP 820173©2017 Volkswagen Group of America, LLC. All rights reserved. All information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Volkswagen Group of America, LLC. Always check Technical Bulletins and the latest electronic repair information for information that may supersede any information included in this booklet. Trademarks: All brand names and product names used in this manual are trade names, service marks, trademarks, or registered trademarks; and are the property of their respective owners. Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Engine Mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Engine Management System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 IntroductionThe 2.0L TSI Generation III B engine is from the EA888 series of engines. The primary goals of this engine are to reduce CO and particulate emissions.1For more information about engines of the EA888 series, see Self-Study Program 820533 The 1.8L and 2.0L TSI 3rd Generation EA888 Gasoline Engines. IntroductionDevelopment of the 2.0L TSI EngineThe recent trend of engine development is to reduce displacement. The next step is to optimize these smaller engines. During development, special attention is placed on balancing displacement, performance, torque and fuel consumption with operating conditions. Customers spend most driving time in the part load range. As a result, this engine focuses on improving economy in that load range.s554_0952 IntroductionTechnical FeaturesEngine Mechanics The mechanical parts of this engine are mostly identical to those in the EA888 2.0L TSI engine. The following components and assemblies have been modified due to the optimized combustion process: • The intake port • The combustion chamber with inlet and exhaust valves • The injectors • The piston Engine Management System The engine management system has the following characteristics: • Valvelift system on the intake side • Injection pressure increased to 250 bar • Mass Airflow Sensor G70 between the turbocharger and air filter housing • Engine Control Module with quad core processor • Intake camshaft and exhaust camshaft adjustment • Innovative thermal management with rotary valve regulation (actuator for Engine Temperature Control Actuator N493) • On-demand piston cooling jets • Intake manifold flapsTechnical Data 265 235 200 165 Torque 135 100 65 35 01000 2000 3000 4000 5000 6000215 190 160 135 110 80 55 25 0 Engine Speed [rpm] HorsepowerType Displacement Bore Stroke Valves per Cylinder Compression Ratio Maximum Output Maximum Torque Engine Management System Fuel Exhaust Gas Treatment4-cylinder in-line engine 1984cm3 82.5mm 92.8mm 4 11.6 : 1 183 hp (137kW) from 3940 to 6000 rpm 221 lb/ft (300Nm) from 1500 to 3940 rpm Bosch MG1 Regular unleaded Three-way catalytic converter, a broadband lambda probe upstream of the turbocharger and a step-type lambda probe downstream of the catalytic converter3Volkswagen Technical Site: http://vwts.ru http://vwts.info Engine MechanicsThe Technical ChangesThe following is an overview of the main changes to the 2.0L TSI engine. Component Cylinder block Change • Blow-by gases passed via balance shaft on inlet side through slotted plastic sleeve • More precision required for installation of piston cooling nozzles on account of changes to crankcase breather system (see workshop manual)s554_032Cylinder head• Valvelift system on intake side • Intake ports have been straightened • Changes to combustion chambers • Valves and injectors have been moved further back into combustion chamber • Three-part oil scraper ring • Piston crowns modified for deeper valve pocketss554_024Pistons554_022Note: New special tool for piston installation. • Oil pump drive gear with 22 teeth instead of 24 teeth for higher ratio • Faster build-up of oil pressureOil pumps554_0854 Engine MechanicsComponent Chain drive Change • Longer guide rail to prevent timing chain slipping • Crankshaft chain has three sprockets: – Oil pump drive – Balancer shaft drive – Camshaft drive • Camshaft chain sprocket is designed to be off center to reduce chain forces on timing chain. • Increase of injection pressure to 250bar, resulting in finer atomization of fuel in combustion chambers554_029Fuel systems554_021Engine management system• Bosch MG1 with four core processorss554_020Valve stem oil seal• Valve stem oil seals of exhaust valves have a double lip for better sealings554_0865 Engine MechanicsCrankcase VentilationThe addition of the valvelift system on the intake side of the engine required changes to the crankcase breather system. The blow-by gases exit the crankcase near cylinders 1 and 2, move through the balance shaft area and exit to the fine separator module in the cylinder head. The balance shaft has a slotted plastic sleeve to allow the blow-by gases to flow through. A large amount of the oil from the blow-by gases is separated (centrifugal effect) by rotation of the balance shaft, flowing back into the oil sump. This allows the balance shaft to function as a coarse oil separator. Cylinders 1 and 2 Flow of Blow-by Gases to Fine Separator ModuleBlow-by-Gases from CrankcaseBalance Shafts554_0976Slotted Plastic Sleeve Engine MechanicsCylinder HeadChanges to the cylinder head were needed for an optimized combustion process. Smooth running and knock reduction were also improved. The cylinder head of the engine was changed as follows: • Valvelift system on intake side • Increase in compression ratio from 9.6 to 11.6 by: – lowering combustion chamber roof by 9mm – modified piston crown • Injectors located closer to combustion chambers • Intake ports designed to be straighter in order to optimize the inlet air flow • Valve stem oil seal of exhaust valves with double lipValvelift System on Intake SideIntake PortsCylinder 1-4 Fuel Injector N30 - N33 (TSI injectors)s554_0987 Engine MechanicsThe Combustion Chamber DesignThe combustion chamber is the area between the cylinder head and the piston crown. The combustion chamber depression has a larger compression zone, which requires the use of smaller intake valves. The larger compressing zone provides better mixing of the fuel and air in the cylinder. To help with this, the piston crown valve pockets and the gas flow recess have been optimized.s554_098Combustion ChamberCombustion Chamber Depression in Cylinder Head Inlet Valve Exhaust Valve Compressing ZoneCombustion Chamber Design in Piston Crown Gas Flow RecessCompressing ZoneInjection Apertures554_100 s554_101Inlet ValveSpark PlugExhaust ValveAdapted Valve Pockets8 Engine MechanicsThe Three-Part Oil Scraper RingThe pistons use a three-part oil scraper ring. It has two steel plates, a spacer and expander spring.Top Steel PlateSpacer and Expander SpringBottom Steel Plates554_102When installing the oil scraper rings, make sure that the expander spring is positioned correctly. This is especially important on pistons with the rings pre-installed. There is a risk that the ends of the springs could have shifted above each other. Both ends of the expander spring have a colored marking so that the exact position can be determined. The expander spring must not overlap or the oil scraper ring will not work. The ends of the three-part oil scraper ring must be rotated by 120° during installation.9 Engine Management SystemSystem OverviewSensorsThrottle Valve Control Module GX3 EPC Throttle Drive Angle Sensor 1 & 2 G187, G188 Brake Lamp Switch F Clutch Position Sensor G476 Accelerator Pedal Module GX2: Accelerator Pedal Position Sensor G79 Accelerator Pedal Position Sensor 2 G185 Knock Sensor 1 G61 Low Fuel Pressure Sensor G410 Camshaft Position Sensor G40 Camshaft Position Sensor 3 G300 Engine Coolant Temperature Sensor G62 Engine Coolant Temperature Sensor on Radiator Outlet G83 Engine Speed Sensor G28 Oil Level Thermal Sensor G266 Intake Manifold Runner Position Sensor G336 Intake Manifold Sensor GX9: Manifold Absolute Pressure Sensor G71 Intake Air Temperature Sensor G42 Fuel Pressure Sensor G247 Charge Air Pressure Sensor G31 Oxygen Sensor 1 before Catalytic Converter GX10 Lambda probe G39 Oxygen Sensor 1 after Catalytic Converter GX7: Oxygen Sensor after Catalytic Converter G130 Oil Pressure Switch F1 Reduced Oil Pressure Switch F378 Oil Pressure Switch, Level 3 F447 Fuel Delivery Unit GX1: Fuel Level Sensor G Fuel Level Sensor 2 G169 Driving Profile Selection Button E735 Start/Stop Mode Button E693 Engine Control Module J623 Instrument Cluster Control Module J285 Malfunction Indicator Lamp K83 Electronic Power Control Malfunction Indicator Lamp K132Mass Airflow Sensor G70Charge Air Pressure Actuator V465 Additional Input Signals10Transmission Neutral Position Sensor G701 Engine Management SystemActuatorsPiston Cooling Nozzle Control Valve N522 Ignition Coil 1-4 with Power Output Stage N70, N127, N291, N292 Throttle Valve Control Module GX3: Throttle Valve Control Module J338 EPC Throttle Drive G186 Cylinder 1-4 Fuel Injector N30-33Vehicle Electrical System Control Module J519Dual-Clutch Transmission Mechatronic J743Coolant Shut-off Valve N82 Turbocharger Recirculation Valve N249 Intake Manifold Runner Control Valve N316Data-Bus On Board Diagnostic Interface J533Heater Support Pump V488 Camshaft Adjustment Valve 1 N205 Exhaust Camshaft Adjustment Valve 1 N318Fuel Metering Valve N290 Oil Pressure Regulation Valve N428 Cylinder 1-8 Intake Cam Actuator A or B N577, N576, N584, N585, N592, N593, N600, N60 Charge Air Cooling Pump V188 EVAP Canister Purge Regulator Valve 1 N80 Engine Temperature Control Actuator N493 Fuel Pressure Regulator Valve N276 Oxygen Sensor 1 before Catalytic Converter GX10: Oxygen Sensor Heater Z19 Charge Air Pressure Actuator V465 Oxygen Sensor 1 after Catalytic Converter GX7: Heater for Oxygen Sensor 1 After Catalytic Converter Z29 Fuel Pump Control Module J538 Fuel Delivery Unit GX1: Transfer Fuel Pump G6 Additional Output SignalsRadiator Fan VX5711Motronic Engine Control Module Power Supply Relay J271 Engine Management SystemEngine Control Module J623The engine management system is a Bosch MG1. Bosch is the manufacturer of control module: • M = Motor (engine) • G = Gasoline • 1 = 1st processor generations554_020It uses a 32bit, 300MHz quad core processor. Two main processors are responsible for the actual computing work. Two additional processor cores monitor the computing steps of the main processors. These attributes make it possible to perform various operating modes without reaching the engine control module’s performance limits.Mass Airflow Sensor G70 This mass airflow sensor with backflow detection measures the air mass in the intake port. It is needed because, with the optimized Miller combustion process, the intake valve closes prematurely. When this happens, the intake air flows back into the intake port from the closed intake valve. As this air mass flows back, it is measured by the backflow detection feature.s554_03412 Engine Management SystemThe Principle of 4-stroke CombustionThe Otto 4-stroke Combustion Cycle Many different approaches have been implemented to improve the performance of the Otto cycle engine over the years. The goal was always to get more power from the fuel-air mixture. Intake Compression Combustion Exhaust BackgroundValve lifts554_080TDC The Miller Combustion Process Ralph Miller optimized the Otto combustion process and patented his design in 1947. It involves closing the intake valve before bottom dead center. This results in an increased combustion chamber size. As the piston makes its downward stroke towards bottom dead center, the air is decompressed and cooled. As bottom dead center is passed, the air is compressed. This increases the efficiency of the fuel-air mixture. Valve liftBDCTDCBDCTDCIntakeCompression CombustionExhausts554_082TDCBDC Inlet Valve ClosesTDCBDCTDC13 Engine Management SystemThe Optimized Miller Combustion Process from VolkswagenThanks to the valvelift on the intake side of the engine, the 2.0L TSI engine has the capability to mimic an Otto Cycle or a Miller Cycle engine. Generally, it operates similar to an Otto Cycle during acceleration and high loads, and operates similar to a Miller Cycle for part throttle low-load conditions for economy and emissions. The valvelift system on the intake camshaft makes it possible to switch between short and long valve lift durations, depending on the engine load. At idling speed and in the part load range, the valve lift and duration is shorter. When the engine is placed under greater load, the valve lift and duration is larger. Also, the intake and exhaust camshaft timing can be changed using variable valve timing.Short valve lift in the optimized combustion process With the short valve lift, the intake valve closes (in conjunction with premature setting of the variable valve timing) before bottom dead center (BDC) is reached. The fresh mixture is decompressed as it approaches BDC and cooled in the process. Intake The shorter valve lift with its smaller cross section increases the speed of the air flow into the cylinder. This improves mixing of the fuel and air, and is supported by the geometrical shape of the combustion chamber. This results in: • a greater degree of efficiency in the fuel-air mixture • lower fuel consumption • fewer harmful emissions Compression Combustion ExhaustValve liftValvelift Systems554_083TDCBDC TDC Intake Valve ClosesBDCTDC14 Engine Management SystemLong Valve Lift in the Combustion Process The engine switches to the long valve lift and duration process when a greater demand is required. In combination with a retarded setting of the variable valve timing, the intake valve closes after BDC. This fills the combustion chamber more and provides maximum engine power. Intake Compression Combustion ExhaustValve liftValvelift Systems554_084TDCBDC TDC Intake Valve ClosesBDCTDCModes of OperationCold start • The engine speed is increased, the valve timing adapted, ignition is set to “retarded” and up to three injection sequences are performed. This brings the catalytic converter up to operating temperature quickly. Warm-up phase • Up to a coolant temperature of 70°C, TSI injection occurs between one and three times. Warm start • The intake camshaft is on the small cam profile and valve lift is small respectively. • During the start phase, single or multiple injection takes place during the intake stroke and/or compression stroke depending on the engine temperature. Engine running at operating temperature • With the optimized Miller combustion process or full load depending on the load requirement.15 ServiceFor installing the piston Under no circumstances should a piston ring compressor be used. The oil scraper ring could be damaged beyond repair.T40347 Piston assembly tools554_202VAG1763/13 Screw-in adapters554_203For testing compression pressureFor turning the camshafts T10567s554_20416 Knowledge AssessmentAn on-line Knowledge Assessment (exam) is available for this Self-Study Program. The Knowledge Assessment may or may not be required for Certification. You can find this Knowledge Assessment at: www.vwwebsource.com For Assistance, please call: Volkswagen Academy, Certification Program Headquarters 1-877-791-4838 (8:00 a.m. to 8:00 p.m. EST) Or, E-mail: concierge@volkswagenacademy.com17 Volkswagen Group of America 2200 Ferdinand Porsche Drive Herndon, VA 20171 June 2017