TECHNICAL DOCUMENTATION

SSP 821503 The 2,0L FSI Turbocharged Engine

PDFEN46 pages3 MB
SSP 821503 The 2,0L FSI Turbocharged Engine - PDF cover

This PDF is currently unavailable.

Read document text
The 2.0L FSI Turbocharged Engine Design and FunctionSelf-Study Program Course Number 821503 Volkswagen of America, Inc. Volkswagen Academy Printed in U.S.A. Printed 08/2005 Course Number 821503 ©2005 Volkswagen of America, Inc. All rights reserved. All information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or other wise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Volkswagen of America, Inc. Always check Technical Bulletins and the latest electronic repair information for information that may supersede any information included in this booklet. Trademarks: All brand names and product names used in this manual are trade names, service marks, trademarks, or registered trademarks; and are the property of their respective owners. Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1 2.0L/200 HP 4-Cylinder Turbo FSI Engine with 4-Valves per Cylinder Engine Mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Crankshaft, Engine Block, Pistons, Engine Balance Shaft, Final Drive Sprocket, Toothed Belt Drive, Cylinder Head, Crankcase Ventilation, Exhaust Turbocharger/Manifold Module, Charge Air Ducting and Boost Pressure Control, Boost Pressure Overrun, Cooling System, Tumble Flaps Fuel System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 Demand-Controlled Fuel System, Low Pressure System, High Pressure System Fuel System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Fuel Pump Control Module J538, Transfer Fuel Pump G6, High Pressure Fuel Pump with Fuel Pressure Regulator Valve N276, High Pressure Fuel Pump, High Pressure Fuel Pump Operation, Low Fuel Pressure Sensor G410, Fuel Pressure Sensor G247 , Cylinder Fuel Injectors N30–N33, Fuel Injector Operation, Pressure Limiting Valve, Connector Fitting with Restrictor Engine Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 Modes of Operation, Actuators and Sensor Diagram, Functional Diagram Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Special Tools Knowledge Assessment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40New!Important/Note!This Self-Study Program covers the design and function of the 2.0L FSI Turbo. This Self-Study Program is not a Repair Manual. This information will not be updated. For testing, adjustment and repair procedures, always refer to the latest electronic service information.i ii Introduction2.0L/200 HP 4-Cylinder Turbo FSI Engine with 4-Valves per CylinderThe 2.0L turbocharged FSI engine is first being introduced to the North American market in the 2005 Jetta and the 2006 Passat. Special Features • Exhaust system with two catalytic converters • Hitatchi ethanol-resistant high-pressure fuel pump • Returnless fuel system • Homogeneous fuel injection • Decoupled final drive sprocket in the balance shaft drive gear • Elliptical secondary drive wheel on the crankshaftS339_0461 IntroductionTechnical DataType Displacement Bore Stroke Valves per cylinder Compression ratio Maximum power Maximum torque 4 cylinder, inline 121 cu. in. (1984 cc) 3.2 in. (82.5mm) 3.7 in. (92.8mm) 4Torque and Power243 330 221 300 199 270 177 240 224 165 204 150 184 135 163 120 143 105 109 90 102 75 82 60 61 45 41 30 20 15 2000 4000 6000Torque (ft. lb.)200 HP (147 kW) at 5,100–6,600 rpm 207 ft. lb. (280 Nm) at 1,800–4,700 rpm155 210 133 180 111 150 89 120 66 90 60 44 22 30Engine management Bosch Motronic MED 9.1 Camshaft adjustment 42° crank angle Fuel Premium Plus unleaded, Premium unleaded, Regular unleaded with slight reduction in power Exhaust gas treatment Two three-way catalytic converters with oxygen sensor regulationEngine Speed (rpm)S339_0472Horsepower10.5:1 Engine MechanicsCrankshaftThe crankshaft meets the tough demands of the turbo FSI engine. The main bearing flanges and journals are designed to provide as much strength as possible.S821503_03 FlangesEngine BlockThe cylinder contact surfaces of the cast iron engine block are honed by means of liquid blasting. This type of honing shortens the run-in time of the engine.S337_010PistonsThe crown of the piston is designed to enhance combustion.2.0L 4V T-FSIS337_0113 Engine MechanicsEngine Balance ShaftThe balance shaft assembly used in the engine: • Optimizes engine vibrations • Has an oil pump with a wide gear • Has a pressure control regulator integrated into the balance shaft assembly• High strength die-cast housing • Balance shafts mounted in the aluminum housing • Decoupled final drive sprocket in the balance shaft drive gearDrive GearBalance Wheels Balance Shaft HousingCrankshaftBalance ShaftsIntake Line Final Drive Sprocket S821503_04 Oil Pump4 Engine MechanicsFinal Drive SprocketHigh torsional irregularities from the crankshaft of the turbo engine at low RPMs result in greater chain forces in the balance shaft chain drive. Bow springs have been integrated into the sprocket wheel hub. They decouple the input shaft of the balance shaft unit from the crankshaft. This is similar to a dual-mass flywheel.S337_06 Decoupled Drive Chain Sprocket DiamondCoated Disc Hub Balance Shaft GearPlain BearingBow Spring (2x)Sprocket WheelFriction Disc Diaphragm Spring Cover DiscS821503_055 Engine MechanicsToothed Belt DriveThe toothed belt drive system is designed to meet turbocharging demands using: • High valve spring pressures • Turbo-related valve timing associated with the 42° crank angle adjustment range of the continuous variable valve timing on the intake camshaft • High-pressure oil pump drive from a triple cam on the intake camshaft As a result of these demands, an elliptical toothed belt sprocket was developed. The Crankshaft Torsional Cancellation (CTC) toothed belt sprocket reduces camshaft vibration and the forces acting on the toothed belt. Function The toothed belt drive sprocket is positioned on the crankshaft at TDC of cylinder 1, as shown below. When the cycle begins, forces acting on the toothed belt are reduced by the elliptical shape of the toothed belt sprocket. The flat side of the sprocket gear allows a slight slackening of the toothed belt. This slackening helps to reduce wear on the toothed belt, improving reliability and extending replacement intervals.D2D1D2D1S821503_066 Engine MechanicsCylinder HeadThe cylinder head of the 2.0L FSI turbocharged engine incorporates the following features: • Sodium-filled exhaust valves • Reinforced intake valve seat • Roller rocker fingers that reduce the land width of the camshaft and roller • Identical high tension valve springs for both intake and exhaust valves The geometry of the intake port reduces knock and improves running smoothness.337_0167 Engine MechanicsCrankcase VentilationThe crankcase is maintained in a constant vacuum while the engine is running. The crankcase breather that supplies this vacuum is connected to the intake manifold. The crankcase blow-by gases are separated in two stages. In the first stage, the primary oil separator in the oil filter module takes most of the oil out of the gases. A second separator in the cylinder head cover removes the remainder of the oil from the gases. Since a turbo engine requires a more sophisticated pressure control system, a two-stage pressure control valve is located on the cylinder head cover. If vacuum exists in the intake manifold, blow-by gases flow directly into the intake manifold. If a boost pressure is present in the intake manifold, a one-way valve in the pressure control valve housing closes and the blowby gases flow into the cylinder head cover ahead of the turbocharger. The system can detect faulty installation of the pressure control valve. Unmetered air is detected by the reaction of the oxygen sensor.8 Engine MechanicsIf a boost pressure is present upstream of turbocharger If a vacuum is present in the intake manifold Exhaust Turbocharged Gas OutletIntake Manifold Gas OutletCylinder Head Cover PassagesPrimary Oil SeparatorOil Filter Module332_057 Non-Return Valve Pressure Control Valve Diagnostic Channel Non-Return Valve9 Engine MechanicsExhaust Turbocharger/Manifold ModuleTo conserve space and improve performance and serviceability, the exhaust manifold and turbine housing have been combined into a single module. Special emphasis was placed on easy removal and installation of the exhaust manifold and the close-coupled catalytic converter. The turbine shaft mount is integrated into the compressor housing. The air intake includes connections for crankcase and Evaporative Emission (EVAP) Canister Purge Regulator Valve N80. A silencer reduces pressure pulsation noises. Boost pressure is controlled by a Wastegate Bypass Regulator Valve N75. A Turbocharger Recirculating Valve N249 keeps a portion of air running through the intake side of the turbocharger when the throttle valve is closed and boost pressure is still present. This keeps the turbocharger impeller from slowing down, reducing turbo lag when the throttle is applied again. The Wastegate Bypass Regulator Valve N75 and the Turbocharger Recirculating Valve N249 are located on the turbocharger.Crankcase Breather Connection Coolant Flow to Radiator and from Auxiliary Water PumpEvaporative Emission (EVAP) Canister Purge Regulator Valve N80Pressurized Oil InletTurbocharger Recirculating Valve N249Oil ReturnCoolant Inlet from Engine Block332_02410 Engine MechanicsA clamping flange on the cylinder head allows easy removal and installation of the exhaust turbocharger/manifold module. The clamping flange does not require removal.Clamping Flange332_025 Cylinder 1The exhaust manifold is split. A divider in the manifold ensures a steady flow of exhaust gases to the turbine. The ports of cylinders 1 and 4 and cylinders 2 and 3 are separated based on the firing order. The divider also prevents the exhaust gas pressure from expanding into the other cylinders.Divider332_02611 Engine MechanicsCharge Air Ducting and Boost Pressure ControlBoth the boost and intake pressures are used to control the wastegate of the turbocharger. These pressure signals are supplied to the ECM, which then sends a pulse-width modulated signal to the Wastegate Bypass Regulator Valve N75. As a result N75 controls vacuum supply to the Pressure Unit, which directly acts on the wastegate via a connecting rod. This control system regulates the turbine speed and sets the maximum boost pressure. If the control system fails, the boost pressure acts directly on the pressure unit. The increased spring pressure reduces maximum boost down to minimum boost.Turbocharger Recirculating Valve N249 Wastegate Bypass Regulator Valve N75Wastegate Brake Booster ServoVacuum Pump Pressure Unit Water ConnectionEvaporative Emission (EVAP) Canister Purge Regulator Valve N80Oil Filter ModuleCharge Air Cooler 332_01112 Engine MechanicsBoost Pressure OverrunIf the throttle valve closes when the engine is in overrun, back pressure develops in the turbo housing. Back pressure reduces the speed of the turbine, which reduces boost pressure and increases turbo lag when the engine accelerates again. At other engine speeds, the tumble flaps are open to eliminate flow resistance and reduction in engine performance. To avoid this, the Turbocharger Recirculating Valve N249 is opened by an electrical actuator. This allows the compressed air to flow back to the intake side of the circuit through the turbine. This maintains turbine speed. The Turbocharger Recirculating Valve N249 closes when the throttle valve opens again and boost pressure is immediately available.Overrun ModeAir Intake from Air FilterDivert Air Valve Open Engine Running Under LoadDivert Air Valve Closed332_01213 Engine MechanicsCooling SystemTo prevent carbon build-up on the turbine shaft in the turbocharger, an auxiliary coolant pump provides additional coolant circulation for a certain time after the engine is shut off hot. The pump forces the lower temperature coolant against the normal direction of flow. The coolant flows from the radiator through the turbocharger to the engine block and back to the cooler.Connection Heat ExchangerConnection Expansion TankConnection Engine BlockCoolant PortConnection Exhaust-Driven TurbochargerCoolant ThermostatRadiator Outlet Oil Cooler Auxiliary Coolant PumpRadiator InletKey: Red arrows indicate normal coolant flow with engine running. Blue arrows indicate reverse coolant flow from the auxiliary water pump with the engine OFF .S821503_0714 Engine MechanicsTumble FlapsTumble flaps are individual plates located within the intake manifold runners that can either stay in a flat position to allow maximum airflow or move up to redirect the airflow into the combustion chamber. At different engine rpms, the tumble flaps are activated to enhance the air/fuel mixture. The tumble flaps are actuated: • To improve cold engine idling • To improve charge efficiency at start-up • In overrun mode At other engine speeds, the tumble flaps are open to eliminate flow resistance and reduction in engine performance.High-Pressure Rail Plastic Flap with Steel Shaft High-Pressure/ Low-Pressure Fuel PortTorque (ft. lbs.) 230 207 177 148 118 89 59 30 0 0 Output (kW) 218 190 163 136 109 82 54 27 0 1000 2000 3000 4000 5000 6000 7000 Speed (rpm) which tumble flaps are closedRange inS821503_08Intake Air Temperature SensorThrottle Valve Actuator Evaporative Emission (EVAP) Canister Purge Regulator Valve N80332_058 Tumble Flap ActuatorPressure Limiting Valve15 Fuel System OverviewDemand-Controlled Fuel SystemThe demand-controlled fuel system combines the advantages of the low pressure electric fuel pump with the high pressure fuel pump by providing only as much fuel as the engine needs at any given time. This reduces the electrical and mechanical power requirements of the fuel pumps and saves fuel. The fuel system is divided into low pressure and high pressure systems.Door Contact Switch for Fuel Pump SupplyVehicle Electrical System Control Module J519, Power Supply for Fuel Pump SupplyLow Pressure SystemThe low pressure system maintains fuel pressure in the 7 .3–72.5 psi (0.5–5 bar) range. The pressure is increased to 94.3 psi (6.5 bar) for hot and cold engine startup. Increasing low pressure results in higher pressure in the high pressure system for cold starts. It achieves better mixture preparation and a quicker start. The pressure increase also prevents the formation of vapor bubbles in the high pressure fuel pump for hot starts. Low Pressure System Components Include: • Fuel Pump Control Module J538 • Fuel tank • Transfer Fuel Pump G6 • Fuel filter with pressure limiting valve (opens at approximately 98.6 psi [6.8 bar]) • Low Fuel Pressure Sensor G410Battery Motronic Engine Control Module J220Fuel Pump Control Module J538 Restrictor Return LineFuel Filter with Pressure Limiting ValveTransfer Fuel Pump G6Fuel TankLow Fuel Pressure Sensor G410Key No pressure Low pressure High pressure Low pressure fuel system High pressure fuel system16 Fuel System OverviewHigh Pressure SystemThe high pressure system maintains fuel pressure in the 435–1,595 psi (30–110 bar) range. The pressure range may vary.Fuel Pressure Sensor G247 Pressure Limiting Valve Return LineImportant: Before opening the system, the excess pressure must be bled off. The high pressures of this fuel system can cause injury or death. Always reference the electronic service repair information.High Pressure System Components Include: • High pressure fuel pump • Fuel Pressure Regulator Valve N276 • Fuel railHigh Pressure Fuel Pump• Pressure limiting valve (opens at approximately 1,740 psi [120 bar]) • Fuel Pressure Sensor G247 • Cylinder Fuel Injectors N30–N33Fuel Rail S334_032Fuel Pressure Regulator Valve N276Cylinder Fuel Injectors N30–N3317 Fuel System ComponentsFuel Pump Control Module J538The Fuel Pump Control Module J538 is located in the electric fuel pump cover. Function The Fuel Pump Control Module J538 controls the Transfer Fuel Pump G6 by means of a pulse-width modulated signal (PWM). The control module regulates pressure in the low pressure fuel system from 7 .3–72.5 psi (0.5–5 bar). The pressure is increased to 94.3 psi (6.5 bar) during hot or cold startups. Failure Strategies If the Fuel Pump Control Module fails, the engine will not start or run.S334_024 Fuel Pump Control Module J538Transfer Fuel Pump G6The Transfer Fuel Pump G6 is integrated with the fuel level sensor. This unit is mounted in the fuel tank. Function G6 provides fuel, through the low pressure fuel system, to the high pressure fuel pump. G6 is regulated by a PWM signal from J538.S334_07618 Fuel System ComponentsSystem Operation The Transfer Fuel Pump G6 only provides the required amount of fuel to the engine. Low-Side Fuel pressure is constantly measured by the Low Fuel Pressure Sensor G410 and sent to the Motronic Engine Control Module (ECM) J220. If this pressure deviates from the reference pressure, J220 sends a PWM signal (20 Hz) to the Fuel Pump (FP) Control Module J538. J538 then sends a PWM signal (20 kHz) to the Transfer Fuel Pump G6 until the desired fuel pressure is achieved. Advantages • Less power used because the fuel pump only provides the amount of fuel required by the engine • Lower fuel temperature because only as much fuel is compressed as is required by the engine • Lower noise levels, especially at idle Failure Strategies If the Transfer Fuel Pump G6 fails, the engine will not run.Low Pressure SystemMotronic Engine Control Module J220 PWM Signal (20 Hz) Fuel Pump (FP) Control Module J538 PWM Signal (20 Hz) Transfer Fuel Pump G6 Fuel TankLow Fuel Pressure Sensor G4107 .3–72.5 psi High Pressure Fuel PumpS334_080If either the Motronic Engine Control Module J220 or the Fuel Pump (FP) Control Module J538 is replaced, reference the messages displayed during “Guided fault finding” on the VAS 5051 to perform the adapt procedure.19 Fuel System ComponentsHigh Pressure Fuel Pump with Fuel Pressure Regulator Valve N276The high pressure fuel pump is mounted on the cylinder head. This pump provides between 450 and 1,595 psi (31 and 110 bar) to the fuel rail. Unique Features • The pump is a volume-controlled, singlecylinder, high pressure fuel pump that pumps only as much fuel into the fuel rail as is required for fuel injection. This reduces its output requirements and saves fuel • There is no return line on the high pressure fuel pump. Excess fuel flows back to the low pressure side of the supply lineHigh Pressure Fuel PumpS334_018 Fuel Pressure Regulator Valve N276High Pressure Fuel Pump Drive The high pressure fuel pump is driven by a double cam on the end of the intake camshaft. Important: Before opening the system, the excess pressure must be bled off. The high pressures of this fuel system can cause injury or death. Always reference the electronic service repair information.S334_068 High Pressure Fuel PumpDouble Cam20 Fuel System ComponentsHigh Pressure Fuel PumpBoth fuel lines are metal and are threaded to the pump. The cover cap includes a vent valve that is only required in production. The fuel system is vented during operation by the injectors. The high pressure fuel pump is not serviceable. If the pump fails, replace it as a unit.Low Pressure Fuel Connection S334_022 Cover Cap with Vent Valve High Pressure Fuel Connection Fuel Pressure Regulator Valve N27621 Fuel System ComponentsHigh Pressure Fuel Pump OperationThe high pressure fuel pump is a volumecontrolled, single-cylinder, high pressure pump. It is map-controlled, and pumps only as much fuel as is required for injection. The engine control module calculates the start of the delivery stroke from the required injection amount. When the time is right, the fuel pressure regulating valve closes the inlet valve and the delivery stroke begins.Fuel Pressure Regulating Valve N276 Pump Chamber From Low Pressure Fuel SystemTo Fuel Rail Inlet Valve Outlet ValvePump PlungerS334_058 Double Cam on Intake CamshaftThe chart is divided into three parts representing the pump’s intake stroke, return stroke and delivery stroke. The appropriate stroke section of the chart is shaded. • The blue line indicates the curve of the cam during the rising or falling of the pump plunger • The red line indicates the pressure in the pump chamberIntake StrokeReturn Stroke Delivery StrokeS334_07022 Fuel System ComponentsIntake Stroke During the pump intake stroke, the valve needle spring forces the valve needle to open the inlet valve. Fuel is drawn into the pump chamber by the downward movement of the pump plunger.Valve Needle Valve Needle Spring Pump ChamberInlet Valve Open Pump Plunger Moves Downward S334_060Direction of Double Cam RotationIntake StrokeIntake Stroke Operation• The pump plunger moves down • The pressure in the pump chamber is approximately the same as the pressure in the low pressure fuel systemEnd of Intake StrokeS334_03823 Fuel System ComponentsReturn Stroke The inlet valve remains open as the pump plunger begins to move upward. This allows the fuel quantity to adjust to actual consumption. The pump plunger forces excess fuel back into the low pressure system. The resulting pressure pulses are dampened by the fuel-pressure attenuator and a restrictor located in the fuel supply line.Fuel-Pressure Attenuator Low Pressure SectionOutlet Valve Closed Inlet Valve Open Pump Plunger Upward Movement S334_056Return Stroke Operation• The pump plunger begins its upward stroke with the inlet valve remaining open. Pressure in the pump chamber is approximately the same pressure as the low pressure fuel systemReturn Stroke Start of Return Stroke End of Return StrokeS334_04024 Fuel System ComponentsDelivery Stroke At the beginning of the delivery stroke the fuel pressure regulating valve is briefly energized to force the valve needle back against the force of the valve needle spring, allowing the inlet valve to be closed by the force of the inlet valve spring. Pressure builds in the pump chamber as the pump plunger moves upward. When the pressure in the pump chamber is higher than the pressure in the fuel rail, the outlet valve opens and fuel is forced into the fuel rail.Valve Needle Fuel Pressure Regulator Valve N276 Inlet Valve Spring Pump Chamber To Fuel RailOutlet Valve Open Inlet Valve Closed Valve Needle Spring Pump Plunger Moves UpwardsS334_058Delivery Stroke OperationDelivery Stroke Start of End of Delivery Stroke Delivery Stroke• The pump plunger continues its upward stroke • Pressure in the pump chamber increases. Pump pressure starts to fall when the pump plunger reaches it highest point. This is the end of the delivery stroke The start of the delivery stroke varies depending on the amount of fuel required.VariableS334_04225 Fuel System ComponentsLow Fuel Pressure Sensor G410The Low Fuel Pressure Sensor G410 is located in the high pressure fuel pump supply line. The sensor measures fuel pressure in the low pressure fuel system and sends a signal to the engine control module. Signal Function The engine control module uses the signal from the Low Fuel Pressure Sensor G410 to regulate pressure in the low pressure fuel system. The fuel pressure ranges from 7 .3–72.5 psi (0.5–5 bar) depending on the engine. Failure Mode If the Low Fuel Pressure Sensor G410 fails, a fixed PWM signal activates the Transfer Fuel Pump G6 to increase pressure in the low pressure system.S334_012 Low Fuel Pressure Sensor G41026 Fuel System ComponentsFuel Pressure Sensor G247The Fuel Pressure Sensor G247 for the high pressure system is located on the lower part of the intake manifold in the fuel rail. The sensor measures fuel pressure in the fuel rail and sends a signal to the engine control module. Signal Function The engine control module uses the signal from the Fuel Pressure Sensor G247 to regulate pressure in the fuel rail via the fuel pressure regulating valve. The fuel pressure may range from 435–1,595 psi (30–110 bar) depending on the engine. Failure Mode If the Fuel Pressure Sensor G247 fails, the Engine Control Module J220 sets the Fuel Pressure Regulating Valve N276 at a predetermined fixed pressure.S334_014 Fuel Pressure Sensor G247 , High Pressure System27 Fuel System ComponentsCylinder Fuel Injectors N30–N33The high-pressure fuel injectors are mounted in the cylinder head and inject high-pressure fuel directly into each combustion chamber. Fuel Injector Function The fuel injectors spray atomized fuel directly into the combustion chamber.S334_054 High-Pressure Fuel InjectorsSpecial tools are required for installation of the injector seals. Please reference the latest service information.Support WasherSupport RingCombustion Chamber Sealing RingFuel Rail O-Ring Seal S334_082 Extractor Groove in InjectorRadial Compensator Ensures Full Contact28 Fuel System ComponentsFuel Injector OperationDuring fuel injection, the injector’s solenoid is activated producing a magnetic field. This energizes the solenoid armature’s valve needle opening the valve, injecting fuel. When activation stops, the magnetic field collapses and the valve needle is forced back into the valve seat by the compression spring stopping fuel flow. Failure Strategy If a defective fuel injector is detected by the misfire detection circuit, that fuel injector is deactivated.Fine-Mesh StrainerSolenoid CoilValve Needle with Solenoid ArmatureTeflon Sealing Ring Outlet HoleS334_08329 Fuel System ComponentsPressure Limiting ValveThe pressure limiting valve is mounted in the fuel rail and protects components from damage caused by excessive fuel pressure. The pressure limiting valve is mechanical and only opens at fuel pressures above 1,740 psi (120 bar). The valve releases fuel from the fuel rail via the return line to the fuel supply line. There the fuel is directed back to the high-pressure fuel pump. The short return line on the engine eliminates the long return line that runs to the fuel tank.S334_016 Fuel Rail Fuel Supply Line High-Pressure Fuel Pump Low Pressure ConnectionReturn LinePressure Limiting ValveConnector Fitting with RestrictorThe connector fitting is located between the fuel supply line and the return line and includes a 0.06 in. (1.5mm) diameter restrictor. The connector fitting with restrictor ensures that: • The high fuel pressure from the high pressure fuel pump is reduced during return • The high fuel pressure from the fuel rail is reduced when the pressure limiting valve is open This also prevents pulses in the fuel line and eliminates noise transmitted by the fuel supply line through attachment points to the vehicle’s body.Fuel Supply LineConnector Fitting with RestrictorS334_086 Return Line30 Engine ManagementModes of OperationThe 2.0L turbocharged engine operates in two modes. Cold Start Dual Injection Dual injection is a special mode of operation for rapid heating of the catalytic converter. To do this, a quantity of fuel is injected on the intake stroke at approximately 300˚ before TDC of ignition. The fuel distributes itself homogenously due to the long gap before ignition. The second injection occurs at approximately 60˚ before TDC of ignition during the compression phase. The rich mixture that forms around the spark plug means that timing can be retarded to a considerable degree without affecting engine stability. Dual injection also achieves stoichiometric (14.7:1) optimum air/fuel ratio. With the exhaust valves open, the exhaust temperature inceases rapidly bringing the catalytic converter up to operating temperature 662°F (350˚C) very quickly (30–40 seconds). Normal Mode The normal mode of operation occurs with the catalytic converter at operating temperature. Normal injection timing occurs because additional heating of the catalytic converter is no longer necessary. The oxygen sensor reaches and maintains a lambda value of 1 (stoichiometry). The electric fuel pump remains energized after the engine reaches operating temperature to maintain pressure in the fuel line and prevent heat bubbles in the fuel. Low Pressure System Prestart Operation When the driver door is opened, the door contact switch causes the electric fuel pump to energize. The purpose of the prestart is to minimize the start time and build up fuel pressure more rapidly. A counter monitors the number of prestarts and prevents pump damage.31 Engine ManagementActuators and Sensor DiagramMass Air Flow (MAF) Sensor G70 Charge Air Pressure Sensor G31 Manifold Absolute Pressure (MAP) Sensor G71 Engine Speed (RPM) Sensor G28 Camshaft Position (CMP) Sensor G40 Throttle Drive Angle Sensor 1 [for Electronic Power Control (EPC)] G187 Throttle Drive Angle Sensor 2 [for Electronic Power Control (EPC)] G188 Throttle Valve Control Module J338 Throttle Position (TP) Sensor G79 Accelerator Pedal Position Sensor 2 G185 Brake Light Switch F Brake Light Switch F63 Fuel Pressure Sensor G247 Intake Manifold Runner Position Sensor G336 Knock Sensor (KS) 1 G61 Knock Sensor (KS) 2 G66 Engine Coolant Temperature (ECT) Sensor G62 Engine Coolant Temperature (ECT) Sensor (on Radiator) G83 Low Fuel Pressure Sensor G410 Intake Air Temperature (IAT) Sensor G42 Heated Oxygen Sensor (HO2S) G39 Oxygen Sensor (O2S) Behind Three Way Catalytic Converter (TWC) G130 Exhaust Gas Temperature (EGT) Sensor 1 G235 Clutch Position Sensor G476 Alternator DFS821503_10 Diagnosis Connection Barometric Pressure (BARO) Sensor F96 Motronic Engine Control Module J22032 Engine ManagementFuel Pump (FP) Control Module J538Cruise Control On/Off Fuel Level Sensor G Transfer Fuel Pump (FP) G6 Fuel Injectors N30–N33 Ignition Coil with Power Output Stage N70, N127 , N291, N292 Throttle Valve Control Module J338 Throttle Drive [for Electronic Power Control (EPC)] G186 Motronic Engine Control Module (ECM) Power Supply Relay J271 Engine Component Power Supply Relay J757 Power Supply Relay (Terminal 15) J329 Evaporative Emission (EVAP) Canister Purge Regulator Valve N80 Fuel Pressure Regulator Valve N276Intake Flap Motor V157 Camshaft Adjustment Valve 1 N205 Wastegate Bypass Regulator Valve N75 Turbocharger Recirculating Valve N249 Oxygen Sensor (O2S) Heater Z19 Oxygen Sensor (O2S) Heater 1 [behind Three Way Catalytic Converter (TWC)] Z29 Coolant Circulation Pump Relay J151 After-Run Coolant Pump V51 Coolant Fan Control (FC) Control Module J293S821503_1133 Engine ManagementFunctional DiagramA F F47 G G1 G6 G28 G31 G39 G40 G42 G61 G62 G66 G70 G79 G83Battery Brake Light Switch Brake Pedal Switch Fuel Level Sensor Fuel Gauge Transfer Fuel Pump (FP) Engine Speed (RPM) Sensor Charge Air Pressure Sensor Heated Oxygen Sensor (HO2S) Camshaft Position (CMP) Sensor Intake Air Temperature (IAT) Sensor Knock Sensor (KS) 1 Engine Coolant Temperature (ECT) Sensor Knock Sensor (KS) 2 Mass Air Flow (MAF) Sensor Throttle Position (TP) Sensor Engine Coolant Temperature (ECT) Sensor (on Radiator)G130 G185 G186 G187 G188 G247 KeyOxygen Sensor (O2S) Behind Three Way Catalytic Converter Accelerator Pedal Position Sensor 2 Throttle Drive (for Electronic Power Control (EPC)) Throttle Drive Angle Sensor 1 (for Electronic Power Control (EPC)) Throttle Drive Angle Sensor 2 (for Electronic Power Control (EPC)) Fuel Pressure Sensor Output Signal Ground Input Signal Positive CAN Drive Train34 Engine ManagementG336 G410 G476 J220 J235 J285 J317 J329 J338 J519 J533 J538 J682 J757 N30 N31 N32 N33 N70Intake Manifold Runner Position Sensor Low Fuel Pressure Sensor Clutch Position Sensor Motronic Engine Control Module (ECM) Engine Coolant Pump Relay Instrument Cluster Control Module Power Supply Relay (Terminal 30, B+) Power Supply Relay (Terminal 15) Throttle Valve Control Module Vehicle Electrical System Control Module Data Bus On Board Diagnostic Fuel Pump (FP) Control Module Power Supply Relay (Terminal 50) Engine Component Power Supply Relay Cylinder 1 Fuel Injector Cylinder 2 Fuel Injector Cylinder 3 Fuel Injector Cylinder 4 Fuel Injector Ignition Coil 1 With Power Output StageN75 N80 N127 N205 N249 N276 N291 N292 P Q S T16 V50 V157 Z19 Z29Wastegate Bypass Regulator Valve Evaporative Emission (EVAP) Canister Purge Regulator Valve Ignition Coil 2 with Power Output Stage Camshaft Adjustment Valve 1 Turbocharger Recirculating Valve Fuel Pressure Regulator Valve Ignition Coil 3 with Power Output Stage Ignition Coil 4 with Power Output Stage Spark Plug Connectors Spark Plugs Fuse 16-Pin Connector Coolant Pump Intake Flap Motor Oxygen Sensor (O2S) heater Oxygen Sensor (O2S) Heater 1 (Behind Three Way Catalytic Converter (TWC))S337_02535 ServiceSpecial ToolsDesignation T10252 Camshaft bar Tool Application Locks camshaft to allow pulley removalVAG 1687 Charge air system testerTo check for leaks in charge air systemWith new adapter 687/536 ServiceDesignation T10133 FSI special tool caseToolApplication Contains tools for injector removal, injection seal installation and injector installation.T40057 Oil drain adapterTo drain engine oil from oil filter housingT40001 PullerTo remove camshaft pulleyT40001/1–7 Arms for puller37 Notes38 Notes39 Knowledge AssessmentAn on-line Knowledge Assessment (exam) is available for this Self-Study Program. The Knowledge Assessment may or may not be required for Certification. You can find this Knowledge Assessment at:www.vwwebsource.comFrom the vwwebsource.com Homepage: – Click on the Certification tab – Type the course number in the Search box – Click “Go!” and wait until the screen refreshes – Click “Start” to begin the AssessmentFor Assistance, please call:Certification Program Headquarters 1 – 877 – CU4 – CERT (1 – 877 – 284 – 2378) (8:00 a.m. to 8:00 p.m. EST)Or, E-Mail:Comments@VWCertification.com40 Volkswagen of America, Inc. 3800 Hamlin Road Auburn Hills, MI 48326 Printed in U.S.A. August, 2005