TECHNICAL DOCUMENTATION

SSP 822703 Volkswagen 4,2L V8 FSI Engine

PDFEN40 pages1 MB
SSP 822703 Volkswagen 4,2L V8 FSI Engine - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingSelf-Study Program 822703Volkswagen 4.2L V8 FSI Engine Volkswagen Group of America, Inc. Volkswagen Academy Printed in U.S.A. Printed 5/2008 Course Number 822703 ©2008 Volkswagen Group of America, Inc. All rights reserved. All information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen Group of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Volkswagen Group of America, Inc. Always check Technical Bulletins and the latest electronic repair information for information that may supersede any information included in this booklet. Trademarks: All brand names and product names used in this manual are trade names, service marks, trademarks, or registered trademarks; and are the property of their respective owners. ContentsIntroduction ............................................................................... 2Engine Mechanical .................................................................... 4Engine Management ............................................................... 20Functional Diagram ................................................................. 32Service ...................................................................................... 36Knowledge Assessment .......................................................... 37NoteImportant!This Self-Study Program covers information on the Volkswagen 4.2L V8 FSI Engine. This Self-Study Program is not a Repair Manual. This information will not be updated.For testing, adjustment and repair procedures, always refer to the latest electronic service information.i IntroductionTechnical FeaturesThe 4.2 Liter V8 4V FSI engine is the most recent example of the Fuel Straight Injection engines from Volkswagen. It is the successor to the 4.2 Liter V8 5V engine and is used in the Touareg. The 2.0 Liter turbocharged FSI was the first engine introduced by VW with direct injection technology. Following its success, the 3.6 Liter V6 FSI and 4.2 Liter V8 4V FSI were introduced. – Bosch Motronic MED 9.1.1 – Fuel Straight Injection (FSI) – Electronic Throttle (Electronic Pedal Control) – Two hot film mass airflow sensors – Electronically regulated cooling system – Adjustment of the variable intake manifold and intake manifold flap change-over by means of an electric motor – Continuous inlet and exhaust camshaft timing adjustment – Two-piece cylinder block – Chain drives for camshafts and ancillary drives mounted on the flywheel side of the engine – Spur gear drive for ancillary units – Secondary air injection system4.2L V8 FSI EngineS388_0032 IntroductionTechnical DataTorque lb ft (Nm)368 lb ft (500 Nm) 332 lb ft (450 Nm) 295 lb ft (400 Nm) 258 lb ft (350 Nm) 221 lb ft (300 Nm) 184 lb ft (250 Nm) 147 lb ft (200 Nm) 111 lb ft (150 Nm) 74 lb ft (100 Nm) 37 lb ft (50 Nm) 0 0Power hp (kW)402 hp (300 kW) 362 hp (270 kW) 322 hp (240 kW) 282 hp (210 kW) 241 hp (180 kW) 201 hp (150 kW) 160 hp (120 kW) 120 hp (90 kW) 80 hp (60 kW) 40 hp (30 kW) 0 1000 2000 3000 4000 5000 6000 7000 8000rpmS388_004Engine Code Type Displacement in Bore in Stroke in Valves per Cylinder Compression Ratio Maximum Output Maximum Torque Engine Management Fuel Exhaust Gas Treatment Emissions StandardBAR 8 cylinders with 90° V angle 254 cubic in (4163 cc) 3.32 in (84.5 mm) 3.65 in (92.8 mm) 4 12.5 : 1 350 hp (257 kW) at 6800 rpm 325 lb ft (440 Nm) at 3500 rpm Bosch Motronic MED 9.1.1 Premium plus unleaded RON 98 or premium unleaded RON 95 4 catalytic converters, 4 O2 sensors, secondary air system LEV II3 Engine MechanicalChain DriveIn the 4.2l V8 4V FSI engine, the camshafts and ancillary units are driven by a total of four roller chains on two levels. The chain drive is maintenancefree and reduces the over-all length of the engine. The crankshaft drives the two drive gears for the camshaft timing chains via chain drive A. In turn, these two drive gears drive the camshaft adjusters for the exhaust and intake camshafts via chain drives B and C. In chain drive D, the crankshaft drives the drive chain sprocket for ancillary drives. This is used to drive the spur gear for the ancillary units. The chains are tensioned by hydraulic spring tensioners.Chain Drive AChain Drive BChain Drive CS388_005Chain Drive D4 Engine MechanicalAncillary Unit DriveThe ancillary units (engine coolant pump, power steering pump and A/C compressor) are driven by the crankshaft via chain drive D, a spur gear drive, a gear module and four intermediate shafts. The gear module is used to adapt the rotational speed and therefore the delivery rate of the engine coolant and oil pumps.Air Conditioner CompressorCoolant PumpS388_006Oil Pump Gear ModulePower Steering Pump5 Engine MechanicalIntake SystemAs in the 4.2 Liter V8 5V engine used previously in the Touareg, the fresh air intake system is designed with two branches, therefore reducing pressure losses. 4.2L V8 FSI Intake SystemThrottle Valve Module Mass Air Flow (MAF) Sensor G70 Variable Inlet ManifoldBoth intake tracts are brought together upstream of a common throttle valve module. Each intake track is equipped with a mass airflow sensor.Mass Air Flow (MAF) Sensor 2 G246Intake Manifold FlapsS388_007Intake ManifoldThe two-stage variable intake manifold is manufactured from die-cast magnesium. It houses the change-over flaps to vary the length of the intake runners as well as the flaps that change the airflow path near the intake valves.Change-Over FlapS388_008Intake Manifold Flaps6 Engine MechanicalVariable Intake ManifoldSwitching between the long and short intake manifold runners is determined by a performance map of the Engine Control Module. – In the lower engine speed range, the long intake manifold runners are used (torque position) – In the upper engine speed range, the short intake manifold runners are used (output position) The change-over flaps are actuated by an electric motor on command from the Engine Control Module. The change-over flaps have sealing lips to ensure that the long intake manifold remains leak-tight in the torque position.Variable Intake Manifold Runner Motor V183 Selector Shaft with Change-Over FlapsS388_009Intake Manifold Runner Position Sensor G336Intake Manifold FlapsIntake Manifold Flap Change-OverThe intake manifold flaps are installed in the two intake manifold lower sections. They are actuated, depending on load and engine speed, by an intake manifold flap motor and two linkage systems. – At low load and engine speed, they are actuated and close off the lower section of the intake ports. This results in cylindrical-shaped air flow into the cylinder. – At high load and engine speed, they are not actuated, and lie flush against the surface of the intake port in order to avoid flow losses. Due to emission-relevant reasons, the positions of the intake manifold flaps are monitored by two intake manifold flap potentiometers.S388_010Separating PlateIntake Flap Motor V157Intake Manifold Runner Position Sensor 2 G5127 Engine MechanicalCylinder BlockThe cylinder block is manufactured from an aluminum-silicon alloy by means of low-pressure gravity die casting. It is characterized by high strength, very low cylinder warming and good thermal dissipation. To obtain the narrowest cylinder webs possible, cylinder liners have been omitted. Final cylinder bore surface machining is carried out in a three-stage honing and exposure process. During this process, the aluminum is separated from the surface and the silicon is exposed in the form of extremely small and particularly hard particles. These finally form the wear-resistant contact surface for the pistons and the piston rings. The ladder frame is manufactured from an aluminumsilicon alloy by means of die casting. Cast-in bearing caps manufactured from cast iron with nodular graphite reinforce the ladder frame and absorb the majority of the flow of force. Due to their thermal expansion, which is lower than that of aluminum at high temperatures, they limit main bearing clearance. The ladder frame design with bearing caps offers high longitudinal and transverse stiffness.S388_012Crankshaft DriveThe crankshaft is manufactured from high-quality tempered steel, and is supported by five bearings. The large ends of the connecting rods are cracked during manufacture. This ensures a tight, precise fit of the cap after the bearing has been installed. Forged pistons are used for reasons of strength. The piston crowns have been adapted to the combustion process involved in FSI technology, and support the circular flow of air in the cylinder. The piston skirts are coated with Ferrostan, which contains iron. This prevents direct contact between the pistons and the cylinder walls, reducing wear.Piston SkirtCracked Connecting RodCylinder Block Piston Crown CrankshaftCast-In Bearing CapLadder FrameS388_0118 Engine MechanicalCylinder HeadsThe 4-valve cylinder heads are manufactured from an aluminum alloy. This material provides very good thermal conductivity and high strength. – The separating plates for intake manifold flap change-over are installed in the intake ports – The injectors are fitted on the intake side in the cylinder head – The high-pressure fuel pumps are driven by dual cams on the intake camshafts – The cylinder head cover is made of plastic and contains a labyrinth oil separator – The camshafts are fully-assembled (the camshaft lobes are mated to the camshaft by a hydroforming process) and are driven by chain – The exhaust valves are filled with sodium. This reduces the temperature at the valve by 212°F (100°C)Cylinder Head Cover Hall Sender Crankcase Ventilation SystemCamshaft Adjustment SystemThe gas exchange processes in the combustion chamber has a significant influence on output, torque and exhaust gas emissions. The camshaft adjustment system allows these gas exchange processes to be adapted to the engine’s requirements. Camshaft adjustment is carried out continuously by vane adjusters, and has a maximum of 42°. The position of the camshafts are detected by means of four Hall senders. When the engine is not running, the vane adjusters are locked using a spring-loaded locking pin. The intake camshafts are set to the “retarded” position and the exhaust camshafts to the “advanced” position. To achieve this, a return spring is installed in the exhaust camshaft vane adjusters.Intake AdjusterS388_014High-Pressure Fuel Pump with Fuel Metering ValveS388_013Fully Assembled CamshaftExhaust Adjuster with Return Spring9 Engine MechanicalOil SupplyDuring development of the oil supply system, emphasis was placed on achieving the lowest possible oil flow while providing sufficient lubrication. As a result, the camshaft adjusters and various friction bearings were optimized. This engine’s oil flow of 53 qt (50 l) per minute at 7000 rpm at a temperature of 248°F (120°C) is very low. The advantage is that the oil remains in the oil sump for a longer period of time, and that better water and hydrocarbon (uncombusted fuel) degasification is possible. Additionally, a smaller oil pump can be used. This results in reducing the necessary drive power and therefore, lowering fuel consumption. A baffle plate in the area of the intake connection ensures that no oil, which has been worked into a foam by the oil pump, is drawn into the oil system. The oil is cooled by an oil-water heat exchanger.Cylinder Bank 1Chain TensionerOil Filter ModuleCylinder Bank 2Hydraulic Camshaft AdjustmentOil Cooler (Coolant)Oil Pressure Control ValveOil Pump (Gear)Oil Sump Upper SectionS388_017Baffle PlateOil Sump Lower Section10 Engine MechanicalOil PumpThe oil pump is located inside the oil sump upper section and is bolted to the ladder frame. Oil intake is first through a base filter located on the suction side of the pump. All engine lubrication points are supplied from the pressure side of the oil circuit.Pressure Oil Side Return from the EngineOil Filter ModuleThe oil filter module is designed as a full-flow filter. It is located in the inner V of the engine and the filter element can be easily replaced without special tools.CapFilter Element Consisting of Polymer MatS388_019Base Filter Suction SideS388_020To the Engine CircuitFrom the Oil Pump Pressure Side11 Engine MechanicalCrankcase Breather and Ventilation SystemCrankcase Breather System The crankcase breather system is used to flush fresh air through the crankcase. As a result, water vapor and low-boiling hydrocarbons are removed from the crankcase and diverted back into the engine intake air to be burned. The air is removed downstream of the air filter, and is guided into the inner V of the cylinder block by a non-return valve. A restrictor downstream of the nonreturn valve ensures that only the correct quantity of fresh air is supplied to the crankcase. Crankcase Ventilation System Because of the crankcase ventilation system, the uncombusted hydrocarbons (blow-by gases) are returned to the combustion process and do not escape into the outside air. To minimize the oil contained in the blow-by gases, they are separated by a labyrinth oil separator in the cylinder head cover and a three-stage cyclonic micro oil separator. In the cylinder head cover, the gas encounters impact plates, where the larger oil droplets are separated. The gases are then channeled by hoses to the micro oil separator. Here, the smaller oil droplets are separated off, preventing intake valve coking. The induction point downstream of the throttle valve module is integrated into the engine cooling circuit to prevent it from freezing.Cooling Circuit Connection for Heating Crankcase Breather SystemVent LineS388_023Non-Return Valve (Crankcase Breather System) Micro Oil Separator Pressure Limiting Valve12 Engine MechanicalThree-Stage Cyclonic Micro Oil SeparatorThe quantity of uncombusted hydrocarbons and oil vapor is dependent on the engine load and speed. The oil mixed with unburned hydrocarbons is separated by a three-stage cyclonic micro oil separator. Because cyclonic oil separators only perform well in a low volumetric flow range, one, two or three cyclones are released in parallel depending on the quantity of gas. Low Engine Load/Speed — Low Gas Flow At low engine load and speed, the gas flow is low. The gas flows past the control plunger into the first cyclonic oil separator. Here, the oil still present in the gas is pressed outwards by centrifugal force, adheres to the wall and drips into the oil collection chamber. The oil collection chamber contains an oil drain valve, which is closed by the pressure in the crankcase when the engine is running. When the engine is switched off, the valve opens and the collected oil flows into the oil sump through a hose located below the level of the oil. The pressure control valve ensures a constant pressure level and good crankcase ventilation.From the Cylinder Head Cover To the Induction Point Downstream of the Throttle Valve ModuleControl PlungerPressure Control ValveOil Collection Chamber Oil Drain ValveS388_024Increasing Engine Load/Speed — Increasing Gas Flow As the engine load and speed increases, so to does the flow of the blow-by gases. The higher the flow, the greater the force which acts on the control plunger. The control plunger force overcomes the spring force and releases the access ducts to further cyclones.Control Plunger ShiftedS388_02613 Engine MechanicalBypass Valve Opens — Very High Gas Flow The bypass valve ensures that the pressure in the crankcase does not become excessive. If the pressure in the crankcase increases rapidly, for example due to a jammed control plunger or piston ring flutter (may occur at high engine speeds and low load), the cyclones are no longer able to cope with this pressure increase. The pressure continues to rise and now opens the bypass valve. Part of the blow-by gases now flow past the cyclone and are guided to the intake manifold directly through the pressure control valve.S388_050Bypass Valve OpenGases Flow Past the Cyclones14 Engine MechanicalEngine Cooling CircuitThe cooling system is designed as a longitudinal cooling system. The coolant flows in on the intake side, through the cylinder head gasket and into the head, where it flows out through the timing chain cover. Cylinder web cooling has been improved by drilling coolant ducts with cross-sections into the webs. Forced flow through these bores is ensured with the aid of specifically sealed water ducts. In addition, the engine is equipped with an electronically controlled cooling system. – In the partial load range which is not critical with regards to engine knock, the coolant temperature is regulated to 221°F (105°C). In the lower partial load range, the thermodynamic advantages and reduced friction result in a fuel saving of approximately 1.5%. – In the full load range, the coolant temperature is regulated to 194°F (90°C) by the map-controlled engine cooling system thermostat. This creates cooler combustion chambers and better cylinder charging with reduced knock tendency.Heating System Heat Exchanger Recirculation Pump V55 Engine Coolant Temperature (ECT) Sensor G62Expansion TankOil CoolerCoolant Pump Engine Coolant Temperature (ECT) Sensor (on Radiator) G83 Alternator Radiator Map Controlled Engine Cooling Thermostat F265S388_01615 Engine MechanicalFuel SystemThe fuel system is a requirement-controlled fuel system. This means that both the electric transfer fuel pump and the two high-pressure fuel pumps only deliver the amount of fuel required by the engine at that particular moment. As a result, the electrical and mechanical power requirements are reduced and fuel consumption is lowered. The fuel system is sub-divided into a low-pressure and a high-pressure fuel system. – The fuel pressure of up to 102 psi (7 bar) in the low-pressure fuel system is generated by an electric transfer fuel pump, which is actuated by the engine control module through Fuel Pump Control Module J538. – The fuel pressure of 363 psi (25 bar) to 1523 psi (105 bar) in the high-pressure fuel system is generated by two mechanical high-pressure fuel pumps, each of which is driven via a dual cam by the intake camshafts. To minimize fuel pressure pulsations, both highpressure fuel pumps deliver fuel into a common fuel line to the fuel rails. In addition, the high pressure delivery has been designed so that pressure impulses of the pumps are offset at the common rail.Cylinder Fuel Injectors 1 through 4 N30-N33 Fuel Pressure Sensor G247Fuel Metering Valve N290 Fuel RailFuel Metering Valve 2 N402Pressure Limiting Valve 1740 psi (120 bar)Low Fuel Pressure Sensor G410 Leakage LineCylinder Fuel Injectors 5 through 8 N83-N86Fuel Filter Integrated into TankFuel TankS388_02716 Engine MechanicalExhaust SystemThe exhaust system is a twin-branch design. This means that each cylinder head has a separate exhaust tract. The exhaust manifolds are insulated sheet metal manifolds with a gas-tight inner shell. This airgap insulation enables a compact design and fast heating. Additional heat shields are no longer necessary. The exhaust manifolds are secured to the cylinder heads using clamping flanges. Two broadband oxygen sensors are installed downstream of the exhaust manifolds and two oxygen sensors downstream of the pre-catalytic converters. The starter and main catalytic converter substrate material is comprised of ceramic. Both exhaust tracts end in the front silencer. There, the sound waves overlap and noise emissions decrease. Two exhaust pipes lead from the front silencer to the rear silencer. Both exhaust pipes are routed separately in the interior of the rear silencer. The exhaust gas flows into the outside air via two tailpipes.Exhaust Manifold with Air-Gap Insulation Heated Oxygen Sensor (HO2S) 2 G108 Starter Catalytic Converters Oxygen Sensor (O2S) 2 Behind Three Way Catalytic Converter (TWC) G131 Heated Oxygen Sensor (HO2S) G39Oxygen Sensor (O2S) Behind Three Way Catalytic Converter (TWC) G130Front Silencer Main Catalytic Converters Rear Silencer17 Engine MechanicalSecondary Air Injection SystemTo heat the catalytic converters as quickly as possible, the fuel mixture is enriched during coldstarting and warm-up. This results in a higher percentage of uncombusted hydrocarbons in the exhaust gas during this period. Because of the air injection downstream of the exhaust valves, the exhaust gases are enriched with oxygen, leading to oxidation (afterburning) of the hydrocarbons and the carbon monoxide. The heat released during this process also heats the catalytic converter, helping it to reach its operating temperature faster. The secondary air injection system is comprised of: – Secondary Air Injection (AIR) Pump Relay J299 – Secondary Air Injection (AIR) Pump Motor V101 – Two self-opening combination valves Input signals: – Signal from the Oxygen Sensors (for system diagnosis) – Engine Coolant Temperature Sensors – Mass Airflow Sensor load signalsConnection on the Air FilterSecondary Air Injection PumpS388_029Combination Valves (Self-Opening)18 Engine MechanicalSecondary Air InjectionThe secondary air injection system is activated during cold-starting, at the start of the warm-up phase and for test purposes as part of OBD II requirements. In this case, the engine control module actuates the secondary air pump through the secondary air pump relay. When the pressure is present at the combination valves, they open and the air flows downstream of the exhaust valves. Afterburning takes place.Function of the Combination ValvesThe combination valves are self-opening valves. This means that they are opened through the pressure generated by the secondary air pump, and not by vacuum as in the previous secondary air systems.Combination Valve ClosedThe pressure in the combination valves corresponds to ambient pressure. The valves are closed.From the Spring Secondary Air PumpDiaphragmValve Stem Hollowed Out Valve Disk Closed Exhaust Gas SideS388_015Combination Valve OpenIf the current for the secondary air pump is activated by the relay, it begins to deliver air. Pressure builds up due to the fact that the combination valve is closed. This is present at the valve disk and, through the hollowed-out valve stem, at the diaphragm. If a pressure of approximately 6.5 psi (450 mbar) above ambient pressure acts on the diaphragm and the valve disk, the valve opens. The air delivered by the secondary air pump now flows downstream of the exhaust valves and afterburning takes place.From the Secondary Air PumpDiaphragmValve Disk OpenTo the Exhaust ValvesS388_05719 Engine ManagementSystem OverviewSensorsMass Air Flow (MAF) Sensors, G70, G246 Intake Air Temperature (IAT) Sensor G42 Engine Speed (RPM) Sensor G28 Throttle Position (TP) Sensors G79, G185Camshaft Position (CMP) Sensors G40, G163, G300, G301 Throttle Valve Control Module J338 Throttle Drive Angle Sensors [for Electronic Power Control (EPC)] G187, G188 Intake Manifold Runner Position Sensors G336, G512Data Link ConnectorLow Fuel Pressure Sensor G410Engine Control Module J623Fuel Pressure Sensor G247 CAN Drive Bus Engine Coolant Temperature (ECT) Sensor G62Engine Coolant Temperature (ECT) Sensor (on Radiator) G83 Knock Sensors G61, G66, G198, G199Oxygen Sensors G39, G108Oxygen Sensors G130, G131 Brake Light Switch F Brake Pedal Switch F47 Brake Booster Pressure Sensor G294Additional Input Signals20 Engine ManagementActuatorsMotronic Engine Control Module (ECM) Power Supply Relay J271 Fuel Pump (FP) Control Module J538 Transfer Fuel Pump (FP) G6 Fuel Metering Valves N290, N402 Cylinder Fuel Injectors 1 through 8 N30-33, N83-N86 Evaporative Emission Canister Purge Regulator Valve N80 Throttle Valve Control Module J338 Throttle Drive [for Electronic Power Control (EPC)] G186 Intake Flap Motor V157 Variable Intake Manifold Runner Motor V183Camshaft Adjustment Valves (intake) N205, N208Camshaft Adjustment Valves (exhaust) N318, N319 Ignition Coils with Power Output Stages N70, N127, N291, N292, N323-N326 Map Controlled Engine Cooling Thermostat N265 Coolant Circulation Pump Relay J151 Recirculation Pump V55 Oxygen Sensor (O2S) Heaters Z19, Z28 Oxygen Sensor (O2S) Heaters [behind Three Way Catalytic Converter (TWC)] Z29, Z30 Secondary Air Injection (AIR) Pump Relay J299 Secondary Air Injection (AIR) Pump Motor V01 Coolant Fan Control (FC) Control Module J293 Coolant Fan V7 Coolant Fan Control (FC) Control Module 2 J671 Coolant Fan 2 V177 Brake Booster Relay J569 Brake System Vacuum Pump V192 Additional Output SignalsS388_03021 Engine ManagementCAN NetworkingThe diagram below shows the control units with which Engine Control Module J623 communicates through the CAN data bus and exchanges data.J285J428J533 T16 J623 J217 J644CAN Drive Data BusJ104J197J518CAN Convenience Data BusJ234J646J519G85 J255 J527S388_031G85 Steering Angle Sensor J104 ABS Control Module J197 Adaptive Suspension Control Module J217 Automatic Transmission Control Module J234 Airbag Control Module J255 Climatronic Control Module J285 Instrument Cluster Control Module J428 Distance Regulation Control ModuleJ518 Access/Start Control Module J519 Vehicle Electrical System Control Module J527 Steering Column Electronic Systems Control Module J533 Data Bus On Board Diagnostic Interface J623 Engine Control Module J644 Energy Management Control Module J646 Differential Control Module T16 Data Link Connector22 Engine ManagementSensorsMass Air Flow Sensor with Intake Air Temperature Sensor G42 and Mass Air Flow Sensor 2 G246 To minimize pressure losses, the intake tract has a twin-branch design. The most accurate possible air mass signal is achieved using two Mass Air Flow Sensors. Mass Air Flow Sensor G70 is installed along with Intake Air Temperature Sensor G42 in the intake tract on the cylinder bank 1 side. Mass Airflow Sensor G246 is installed in the intake tract on the cylinder bank 2 side.Mass Air Flow Sensor with Intake Air Temperature Sensor G42 (Cylinder Bank 1)The engine control module calculates the mass and the temperature of the air from the signals transmitted by the two Mass Air Flow Sensors and the Intake Air Temperature Sensor.Mass Air Flow Sensor 2 G246 (Cylinder Bank 2)S388_032Signal Use The signals are used to calculate all load- and engine speed-dependent functions. These include the injection period, ignition timing or camshaft adjustment.Effects in the Event of Failure If one or both Mass Air Flow Sensors fail, the throttle valve position and the engine speed are used as correction values. If the intake air temperature sender fails, a fixed, substitute value is used by the Engine Control Module.23 Engine ManagementCamshaft Position Sensors G40, G163, G300, G301Camshaft Position Sensors G40 and G300 are located on cylinder bank 1 and Camshaft Position Sensors G163 and G301 are located on cylinder bank 2. By scanning a quick-start sender wheel, the engine control module recognizes the position of each cylinder bank’s intake and exhaust camshafts Cylinder Bank 1 Camshaft Position Sensor G40 — intake camshaft Camshaft Position Sensor G300 — exhaust camshaftCamshaft Position Sensor G40S388_033Camshaft Position Sensor G300Cylinder Bank 2 Camshaft Position Sensor G163 — intake camshaft Camshaft Position Sensor G301 — exhaust camshaft Signal Use The signals are used to detect the first cylinder at the firing position, for camshaft adjustment, and to calculate the injection point and the ignition timing. Effects in the Event of Signal Failure No further camshaft adjustment takes place if a Camshaft Position Sensor fails. The engine continues to run and also re-starts again after switching off because of run-on recognition, however, torque and power are reduced.Camshaft Position Sensor G163S388_034Camshaft Position Sensor G30124 Engine ManagementLow Fuel Pressure Sensor G410This sensor is installed in the supply line to the two high-pressure fuel pumps. It measures the fuel pressure in the low-pressure fuel system and transmits a signal to the engine control module.Low Fuel Pressure Sensor G410S388_035Signal Use The signal is used by the engine control module to regulate the low-pressure fuel system. Following the sensor signal, the engine control module transmits a signal to Fuel Pump (FP) Control Module J538, which then regulates Transfer Fuel Pump G6 as required.Effects in the Event of Signal Failure If the fuel pressure sensor fails, the fuel pressure is regulated by a fuel pressure pilot control system. The fuel pressure is then approximately 94.2 psi (6.4 bar).25 Engine ManagementFuel Pressure Sensor G247The sensor is located in the inner V of the cylinder block, and is connected to the fuel rail by a separate fuel line. It measures the fuel pressure in the highpressure fuel system and transmits the signal to the engine control module. Signal Use The engine control module evaluates the signals and regulates the pressure in the fuel rail pipes via the two fuel metering valves. Effects in the Event of Signal Failure If Fuel Pressure Sensor G247 fails, no further high fuel pressure is built up. The engine runs in emergency mode with low fuel pressure. Power and torque are reduced.S388_036Fuel RailFuel Pressure Sensor G24726 Engine ManagementIntake Manifold Runner Position Sensors G336 and G512The two intake manifold flap potentiometers are secured to the intake manifold and are connected to the shaft for the intake manifold flaps. They recognize the position of the intake manifold flaps.Intake Manifold Runner Position Sensor 2 G512S388_037Intake Manifold Runner Position Sensor G336Signal Use The position is important, as intake manifold changeover affects air flow in the combustion chamber and the inlet air mass. The position of the intake manifold flaps is therefore relevant to the exhaust gas, and must be checked via self-diagnosis.Effects in the Event of Signal Failure If the signal from the position sensor fails, the position of the intake manifold flaps at the time of failure and the relevant ignition timing are used as substitute values. Power and torque are reduced and fuel consumption increases.27 Engine ManagementActuatorsTransfer Fuel Pump G6The electric fuel pump and the fuel filter are combined to form a fuel delivery unit. The fuel delivery unit is located in the fuel tank. Task Transfer Fuel Pump G6 delivers the fuel in the low-pressure fuel system to the high-pressure fuel pump. It is actuated with a PWM signal by Fuel Pump Control Module J538. Transfer Fuel Pump G6 always supplies the quantity of fuel required by the engine at the present moment in time.S388_038Effects in the Event of Failure If Transfer Fuel Pump G6 fails, engine operation is no longer possible.Fuel Pump G6Fuel Pump Control Module J538Fuel Pump Control Module J538 is mounted under the rear seat on the cover for the electronic fuel pump. Task The Fuel Pump Control Module receives a signal from the Engine Control Module and controls the electronic fuel pump with a PWM signal (pulse-width modulated). It regulates the pressure in the lowpressure fuel system between 72.5 psi (5 bar) and 101.5 psi (7 bar). Effects in the Event of Failure If Fuel Pump Control Module J538 fails, engine operation is not possible.Fuel Pump Control Module J538S388_03928 Engine ManagementFuel Metering Valves N290 and N402The fuel metering valves are located at the sides of the high-pressure fuel pumps. Task They have the task of making the required quantity of fuel available at the required fuel pressure in the fuel rail pipe. Effects in the Event of Failure The metering valves are open when current is not supplied. This means that high pressure is not built-up and the engine runs with the existing fuel pressure from Transfer Fuel Pump G6. As a result, output and torque are significantly reduced.Fuel Metering Valve N290 Fuel Metering Valve N402S388_04029 Engine ManagementIntake Camshaft Adjustment Valves N205 and N208 Exhaust Camshaft Adjustment Valves N318 and N319These solenoid valves are attached to the cylinder head covers. Task Depending on actuation by the engine control unit, they distribute the oil pressure to the camshaft adjusters according to the adjustment direction and adjustment travel. Both camshafts are infinitely adjustable: – Intake camshaft, 42° crank angle – Exhaust camshaft 42° crank angle – Maximum valve overlap angle 47° crank angleS388_041Camshaft Adjustment Valve N205 (Intake)Camshaft Adjustment Valve 1 N318 (Exhaust)Effects in the Event of Failure If an electrical cable to the camshaft adjusters is defective or a camshaft adjuster fails due to mechanical jamming or insufficient oil pressure, no further camshaft adjustment is carried out. Power and torque are reduced.Camshaft Adjustment Valve 2 N208 (Intake)S388_042Camshaft Adjustment Valve 2 N319 (Exhaust)30 Engine ManagementVariable Intake Manifold Runner Motor V183The variable intake manifold motor is bolted to the intake manifold. Task The motor is actuated by Engine Control Module J623 depending on engine load and speed. The motor actuates the change-over flaps via a shaft and switches to the torque (long runners) or the output position (short runners). Effects in the Event of Failure If Variable Intake Manifold Runner Motor V183 fails, intake manifold change-over is no longer possible. The intake manifold remains in the position in which the change-over flaps were located at the time of failure. Power and torque are reduced.S388_043Variable Intake Manifold Runner Motor V183Intake Flap Motor V157The intake manifold flap motor is bolted to the variable intake manifold. Task The motor is actuated by Engine Control Module J623 depending on engine load and speed. Using two operating rods, it adjusts four intake manifold flaps per cylinder bank. If these are actuated, they close part of the intake port in the cylinder head. This leads to circular air movement in the cylinder head and improves mixture formation. Effects in the Event of Failure If Intake Flap Motor V157 fails, the intake manifold flaps can no longer be actuated. This leads to a deterioration in combustion and a reduction in output and torque. The fuel consumption also increases.Intake Flap Motor V157S388_04431 Functional DiagramJ27130 15 87aS S G6 J285J285 S S J285 J538GG169N30N86N83N84N33N32J623A N70N85N31N326N324N323N292N325N291N127G79 P Q P Q P Q P Q P Q P Q P Q P QG18531A G G6 G79Battery Fuel Level Sensor Transfer Fuel Pump Throttle Position (TP) SensorN70 N83N86Ignition Coil 1 with Power Output Stage Cylinder 5 Fuel Injector to Cylinder 8 Fuel InjectorN127 Ignition Coil 2 with Power Output Stage N291 Ignition Coil 3 with Power Output Stage N292 Ignition Coil 4 with Power Output Stage N323-Ignition Coil 5 with Power Output Stage to N326 Ignition Coil 8 with Power Output Stage P Q S Spark Plug Connector Spark Plugs FuseG169 Fuel Level Sensor 2 G185 Accelerator Pedal Position Sensor 2 J271 J285 J538 J623 N30N33 Motronic Engine Control Module (ECM) Power Supply Relay Instrument Cluster Control Module Fuel Pump Control Module Engine Control Module Cylinder 1 Fuel Injector to Cylinder 4 Fuel Injector32 Functional DiagramJ757S G39/Z19S G108/Z28S G130/Z29 G131/Z30N290N402J623J338 G186 G187 G188 G61 G66 G198 G199 G28 G163S388_045G28 G39 G61 G66Engine Speed Sensor Heated Oxygen Sensor (HO2S) Knock Sensor 1 Knock Sensor 2J757Engine Component Power Supply RelayN290 Fuel Metering Valve N402 Fuel Metering Valve 2 S Z19 Z28 Z29 Z30 Fuse Oxygen Sensor (O2S) Heater Oxygen Sensor (O2S) Heater 2 Oxygen Sensor (O2S) 1 (Behind Three Way Catalytic Converter) Heater Oxygen Sensor (O2S) 1 (Behind Three Way Catalytic Converter) Heater Positive Ground Input Signal Output Signal Bi-Directional Cable CAN Data BusG108 Heated Oxygen Sensor (HO2S) 2 G130 Oxygen Sensor (O2S) Behind Three Way Catalytic Converter G131 Oxygen Sensor 2 (O2S) Behind Three Way Catalytic Converter G163 Camshaft Position Sensor 2 G186 Throttle Drive for Electronic Power Control (EPC) G187 Throttle Drive Angle Sensor 1 for Electronic Power Control (EPC) G188 Throttle Drive Angle Sensor 2 for Electronic Power Control (EPC) G198 Knock Sensor 3 G199 Knock Sensor 4 J338 J623 Throttle Valve Control Module Engine Control Module33 Functional DiagramJ151SSSSN208N205N318N319V157V183V7J293V177J671AJ623G163G40G336G512G247G62G300G301A F265 G40 G62Battery Map Controlled Engine Cooling Thermostat Camshaft Position Sensor Engine Coolant Temperature SensorJ293 J623 J671Coolant Fan Control (FC) Control Module Engine Control Module Coolant Fan Control (FC) Control Module 2N205 Camshaft Adjustment Valve 1 (Intake) N208 Camshaft Adjustment Valve 2 (Intake) N318 Camshaft Adjustment Valve 1 (Exhaust) N319 Camshaft Adjustment Valve 2 (Exhaust) S V7 Fuse Coolant FanG163 Camshaft Position Sensor 2 G247 Fuel Pressure Sensor G300 Camshaft Position Sensor 3 G301 Camshaft Position Sensor 4 G336 Intake Manifold Runner Position Sensor G512 Intake Manifold Runner Position Sensor 2 J151 Coolant Circulation Pump RelayV157 Intake Flap Motor V177 Coolant Fan 2 V183 Variable Intake Manifold Runner Motor34F265 Functional DiagramJ708J569 BJ299SJ255SSS V55 V192 V101SF47F J508J623m G410 G83 G294 G70 G42 G246 B N80123 K1Back-Up Light Switch2 CAN Data Bus 3 CAN Data BusS388_045B F F47 G42 G70 G83Starter Brake Light Switch Brake Pedal Switch Intake Air Temperature Sensor Mass Air Flow Sensor Engine Coolant Temperature Sensor (on Radiator)J623 J708 N80 S V55Engine Control Module Residual Heat Relay Evaporative Emission Canister Purge Regulator Valve Fuse Recirculation PumpV101 Secondary Air Injection Pump Motor V192 Brake System Vacuum Pump Positive Ground Input Signal Output Signal Bi-Directional Cable CAN Data BusG246 Mass Air Flow Sensor 2 G294 Brake Booster Pressure Sensor G410 Low Fuel Pressure Sensor K J255 J299 J508 J569 Dash Panel Insert Climatronic Control Module Secondary Air Injection Pump Relay Brake Light Disable Relay Brake Booster Relay35 ServiceSpecial ToolsDesignation Thrust piece T 40051ToolApplication For installing A/C compressor drive sealing ringThrust piece T40052For installing power steering pump drive sealing ringCamshaft clamps T40070For locking camshafts on cylinder bank 1 and cylinder bank 2Locking pins T40071For locking chain tensioners for chain drives A, B, C, DKey T40079For pre-tensioning inlet and exhaust camshafts after installing the camshaft timing chain36 Knowledge AssessmentAn on-line Knowledge Assessment (exam) is available for this Self-Study Program. The Knowledge Assessment may or may not be required for Certification. You can find this Knowledge Assessment at:www.vwwebsource.comFor Assistance, please call:Volkswagen Academy Certification Program Headquarters 1– 877–491–4838 (8:00 a.m. to 8:00 p.m. EST)Or, E-Mail:concierge@volkswagenacademy.com37 822703Volkswagen Group of America, Inc. 2200 Ferdinand Porsche Drive Herndon, VA 20171 Printed in the U.S.A. May 2008