TECHNICAL DOCUMENTATION
SSP 826803 2,0 Liter TDI Common Rail BIN5 ULEV Engine

This PDF is currently unavailable.
Read document text
Service TrainingSelf Study Program 8268032.0 Liter TDI Common Rail BIN5 ULEV EngineCover art file number tbdVolkswagen of America, Inc. Volkswagen Academy Printed in U.S.A. Printed 4/2008 Course Number 826803©2008 Volkswagen of America, Inc. All rights reserved. All information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Volkswagen of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Volkswagen of America, Inc. Always check Technical Bulletins and the latest electronic repair information for information that may supersede any information included in this booklet. Trademarks: All brand names and product names used in this manual are trade names, service marks, trademarks, or registered trademarks; and are the property of their respective owners.ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Engine Mechanics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Engine Management System . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68Knowledge Assessment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73NoteImportant!This Self-Study Program provides information regarding the design and function of new models. This Self-Study Program is not a Repair Manual.This information will not be updated. For maintenance and repair procedures, always refer to the latest electronic service information.iiiPage intentionally left blankIntroductionIntroductionA New Generation of Diesel Engines from VolkswagenThe 2.0 Liter TDI engine with common rail injection system is the first of a new generation of dynamic and efficient diesel engines from Volkswagen. By combining the successful and proven 2.0 Liter TDI engine with common rail technology, Volkswagen is setting new standards in terms of such characteristic TDI attributes as dynamics, driving enjoyment, economy, and reliability. The superior qualities of the 2.0 Liter TDI engine with common rail injection system are oriented towards future challenges in acoustics, comfort, and exhaust gas after-treatment. The lead taken on by Volkswagen in 1993 with the introduction of the first turbocharged direct injection (TDI) diesel engine in a passenger car continues with the 2.0 Liter TDI engine, confirming Volkswagen’s role as a pioneer in diesel technology. The engine offers the potential for future improvements in exhaust gas standards and the associated technologies.S403_0511Notes2OverviewOverviewHeritageThe 2.0 Liter TDI engine with common rail injection system is based on the 1.9 Liter TDI engine with the Unit Injector System (UIS) also known as the “pumpe düse. ” This predecessor engine is one of the most frequently built diesel engines in the world and has seen the broadest use within the Volkswagen Group, from passenger cars to transport vehicles. To accommodate the increasing demand for improvements in acoustics, fuel consumption, and exhaust gas emissions, a large number of engine components were redesigned. The conversion of the injection system to a common rail design is one of the major changes to this engine. Equipped with a special after-treatment system, this engine meets current emissions standards.3OverviewTechnical Characteristics• Common rail injection system with Piezo fuel injectors • Diesel particulate filter with upstream oxidation catalyst • Intake manifold with flap valve control • Electric exhaust gas return valve • Adjustable exhaust gas turbocharger with displacement feedback • Low and high pressure Exhaust Gas Recirculation (EGR) system2.0 Liter TDI Technical DataDesign Displacement Bore Stroke Valves per Cylinder Compression Ratio Maximum Output Maximum Torque Engine Management 4-Cylinder In-Line Engine 120 in3 (1968 cm3) 3.189 in. (81 mm) 3.760 in. (95.5 mm) 4 16.5:1 140 hp (103 kW) at 4000 rpm 236 lb-ft (320 Nm) at 1750 rpm up to 2500 rpm Bosch EDC 17 (Common Rail Control Unit) ULSD / ASTM D975-06b 2-D-S15 (Ultra-Low Sulfur Diesel, under 15 ppm)295 400 134 100 S403_0032.0 Liter TDI Torque and Powerlbs-ft Nm hp kW266360121902363201078020728094701772408060Fuel14820067501181605440Exhaust Gas Treatment High and Low Pressure Exhaust Gas Return, Oxidation Catalytic Converter, Diesel Particulate Filter, NOx Storage Catalytic Converter10002000300040005000Engine Speed [RPM]S403_0074Output = PowerTorqueEngine MechanicsEngine MechanicsCrankshaftThe 2.0 Liter TDI common rail engine uses a forged crankshaft to accommodate high mechanical loads. Instead of the customary eight counterweights, this crankshaft has only four. Using four counterweights reduces the load on the crankshaft bearings, as well as noise emissions that can occur due to the intrinsic motion and vibrations of the engine.CounterweightsPistonsThe 2.0 Liter TDI common rail engine pistons have no valve pockets. This reduces the cylinder clearance and improves the swirl formation in the cylinder. Swirl is the circular flow about the vertical axis of the cylinder. Swirl has a significant influence on the mixture formation. For cooling the piston ring zone, the piston has an annular cooling channel into which piston spray jets inject oil.Oil Pump GearingCounterweightsS403_069Piston BowlThe piston bowl, where the injected fuel is circulated and mixed with air, is matched with the spray pattern of the injection jets and has a wider and flatter geometry than the piston in a pump-injection engine. This allows more homogeneous carburation and reduces soot formation.Annular ChannelRing PackageS403_0045Engine MechanicsCylinder HeadThe 2.0 Liter TDI common rail engine has a crossflow aluminum cylinder head with two intake and two exhaust valves per cylinder. The valves are arranged vertically upright. The two overhead camshafts are linked by spur gears with an integrated backlash adjuster. They are driven by the crankshaft with a toothed belt and the exhaust camshaft timing gear. The valves are actuated by lowfriction roller cam followers with hydraulic valve lash adjusters.Fuel InjectorsIntake CamshaftExhaust CamshaftRoller Cam FollowersCylinder HeadExhaust PortsS403_008Fuel InjectorThe fuel injectors are fixed in the cylinder head with clamps. They can be removed through small caps in the valve cover. An additional feature of the cylinder head are pressure sensors that are integrated into the glow plugs.ClampS403_0846Engine MechanicsFour-Valve TechnologyTwo intake and two exhaust valves per cylinder are arranged vertically suspended in the cylinder head. The vertically suspended and centrally situated fuel injector is arranged directly over the center of the piston bowl. Shape, size, and arrangement of the intake and exhaust channels ensure a good degree of fill and a favorable charge cycle in the combustion chamber. The intake ports are designed as swirl and fill channels. The air flowing in through the fill channel produces the desired high level of charge motion. The swirl channel ensures good filling of the combustion chamber, particularly at high engine speeds.Intake Camshaft Fuel InjectorFill Channel Swirl ChannelExhaust CamshaftExhaust Valves Intake ValvesS403_0617Engine MechanicsIntake Manifold with Flap ValvesInfinitely variable flap valves are located in the intake manifold. Through the positioning of the flap valves, the swirl of the intake air is adjusted based on the engine speed and load. The flap valves are moved by a pushrod connected to the Intake Flap Motor V157 . This step motor is activated by the Engine Control Module (ECM) J623. The Intake Manifold Runner Position Sensor G336 is integrated in the Intake Flap Motor V157 and electronically regulates its movement. It also provides the Engine Control Module (ECM) J623 with feedback of the current position of the flap valves.Design Intake Plenum Intake Manifold Intake Flap Motor V157Swirl ChannelFill ChannelFlap ValveIntake Flap Motor V157 with Intake Manifold Runner Position Sensor G336S403_0108Engine MechanicsFlap Valve FunctionDuring idling and at low engine speeds, the flap valves are closed. This leads to high swirl formation, with results in good mixture formation.Flap ValveFill ChannelSwirl ChannelS403_044During driving operation, the flap valves are adjusted continuously based on the load and engine speed. Thus for each operating range the optimum air movement is available. Starting at an engine speed of approximately 3000 rpm, the flap valves are completely open. The increased throughput of air insures good filling of the combustion chamber. At startup, during emergency operation, and at full load the flap valves are opened.Flap ValveFill ChannelSwirl ChannelS403_0459Engine MechanicsCamshaft OperationThe intake and exhaust camshafts are linked by means of spur gearing with an integrated backlash adjuster. The spur gear on the exhaust camshaft drives the spur gear on the intake camshaft. Valve lash compensation ensures quiet camshaft operation.Intake CamshaftLadder FrameExhaust CamshaftExhaust Camshaft Moving Spur GearS403_013Shim Stationary SpurS403_012Disk Spring Retaining RingMoving Spur Gear Stationary Spur GearDesignThe wider part of the spur gear (stationary spur gear) is a press-fit on the exhaust camshaft. There are ramps on the front face of the stationary spur gear. The narrower part of the spur gear (the moving spur gear) can move in both radial and axial directions. There are recesses for the stationary spur gear ramps in the rear face of the moving spur gear.RampsS403_01410Engine MechanicsHow it Works Both parts of the spur gear are pushed together in an axial direction by the force of a disk spring. At the same time, they are rotated by the ramps.Radial DirectionAxial DirectionDisk SpringS403_015The rotation leads to a gear displacement of the two spur gear parts and effects the lash adjustment between the intake and exhaust camshaft gears.Lash AdjustmentGear DisplacementS403_01611Engine MechanicsCylinder Head GasketThe cylinder head gasket is a four-layer design and has two special attributes that improve the sealing of the combustion chambers. • Vertically profiled combustion chamber seals • Rear flank supportRear Flank SupportS403_103Combustion Chamber SealsVertically Profiled Combustion Chamber Seals The sealing edge at the cylinder bore is referred to as the combustion chamber seal. It is vertically profiled, which means that the edge profile has varying heights around the perimeter of the combustion chamber. This special geometry provides for the uniform distribution of cylinder head gasket sealing forces around the combustion chambers. This prevents deformation at the cylinder bores and fluctuations in the sealing gap.S403_029Rear Flank Support The profile in the area of the two outer cylinders of the cylinder head gasket are referred to as “rear flank support. ” The rear flank support effects a uniform distribution of the gasket sealing forces in these areas. This reduces flexing of the cylinder head and deformation of the outer cylinders.Rear Flank SupportS403_09212Engine MechanicsToothed Belt DriveThe camshaft, the coolant pump, and the highpressure pump for the common rail injection system are driven by a toothed belt.Idler PulleyHigh-Pressure Pump Drive WheelCamshaft Timing GearTensioner Pulley Coolant Pump Drive WheelGenerator Drive WheelCrankshaft PulleyAccessory Drive Ribbed V-BeltTensioner PulleyAir Conditioning CompressorAccessory DriveThe generator and air conditioning compressor are driven by a ribbed V-belt. The profile surface of the ribbed V-belt has a fibrous coating. This improves the frictional properties of the belt, reducing unpleasant noise that can occur in wet and cold conditions.Ribbed V-Belt Tooth ProfileFibrous CoatingS403_11613Engine MechanicsBalance Shaft ModuleThe balance shaft module is installed below the crankshaft in the oil pan. The balance shaft module is driven by the crankshaft by a gear drive. The duocentric oil pump is integrated in the balance shaft module. The gear drive is designed so that the balance shafts rotate at double the crankshaft speed. The tooth backlash of the gear drive is adjusted with the help of a coating on the intermediate gear. This coating wears off during startup of the engine and results in excellent mating of the teeth on the two gears. The intermediate gear must always be replaced if the intermediate gear or the drive gear of the first balance shaft have been loosened. Please refer to the instructions in the Repair Manual.DesignThe balance shaft module consists of a gray cast iron housing, two counter-rotating balance shafts, a helical-toothed gear drive, and an integrated duocentric oil pump. The rotation of the crankshaft is transferred to the intermediate gear on the outside of the housing. This drives the first balance shaft. From this balance shaft, the motion is then transferred inside the housing to the second balance shaft and to the duocentric oil pump.Crankshaft GearIntermediate GearHousingBalance Shaft 1 Drive Gear Duocentric Oil PumpBalance Shaft 2 Drive GearS403_01714Notes15Engine MechanicsOil CircuitA duocentric oil pump generates the oil pressure required for the engine. It is integrated into the balance shaft module and is driven by a balance shaft drive shaft. The pressure relief valve is a safety valve. It prevents damage to engine components from excessive oil pressure, such as at high speeds and low ambient temperatures. The oil pressure control valve regulates the oil pressure in the engine. It opens as soon as the oil pressure reaches the maximum permissible value. The bypass valve opens when the oil filter is clogged to safeguard the lubrication of the engine.16Engine MechanicsS403_106Legend 1 – Oil Pan 2 – Oil Level and Temperature Transmitter 3 – Oil Pump 4 – Oil Pressure Relief Valve 5 – Oil Return Block 6 – Oil Cooler 7 – Oil Filter 8 – Bypass Valve9 – Oil Pressure Switch F1 10 – Oil Pressure Control Valve 11 – Crankshaft 12 – Spraying Nozzles for Piston Cooling 13 – Camshaft 14 – Vacuum Pump 15 – Turbocharger 16 – Oil Return17Engine MechanicsCrankcase VentilationIn combustion engines, pressure differentials between the combustion chamber and the crankcase generate air flow between piston rings and cylinder barrel, which are referred to as blow-by gases. These oily gases are returned to the intake area through the crankcase ventilation system to prevent pollution. Effective oil separation keeps engine oil in the crankcase and prevents it from entering the intake manifold. This multistage system separates more oil than a single-stage system. The oil separation is effected in three stages: • Coarse separation • Fine separation • Damping section The crankcase ventilation components, the oil filler inlet, and the pressure reservoir for the vacuum system of the engine are all integrated in the cylinder head cover.Coarse SeparationThe blow-by gases move from the crankshaft and camshaft chamber into a stabilizing section, which is integrated in the cylinder head cover. In this section, the larger oil droplets are separated onto the walls and collect on the floor. The oil can drip into the cylinder head through the openings in the stabilizing section.Vacuum ReservoirDamping SectionPressure Control Valve Oil Filler InletCoarse Separation Fine SeparationS403_01918Engine MechanicsDesign To the Intake Manifold Cover Diaphragm Pressure Control Valve Support Plate Spiral Spring Damping Section Flutter ValvesStabilizing SectionCyclonesFlutter Valve Oil Collector SectionLegend Oily Air from the Crankcase Air Cleaned of Oil Oil ReturnS403_08619Engine MechanicsFine SeparationThe fine separation takes place over a cyclone separator consisting of a total of four cyclones. Depending on the amount of the pressure differential between the intake manifold and the crankcase, two or four cyclones are activated by spring steel flutter valves. Due to the geometry of the cyclones, the air is set into a rotating motion. The resulting centrifugal force slings the oil mist onto the separator wall. The oil droplets are deposited on the wall of the cyclone and are captured in a collector section. When the engine is OFF , a flutter valve opens. This valve closes during engine operation due to the increased pressure in the cylinder head. The sole purpose of this valve is to let oil drain back into the engine sump when the engine is OFF .Cyclones Pressure Control Valve Flutter ValvesCleaned Air to the Intake PortOil Collector Section Oil to the CrankcaseFlutter ValveS403_08720Engine MechanicsPressure Control ValveThe pressure control valve regulates the pressure for ventilation of the crankcase. It consists of a diaphragm and a pressure spring. When blow-by gases are present, the pressure control valve limits the vacuum in the crankcase. Excessive vacuum in the crankcase could result in damage to the engine seals. If the vacuum in the intake port is too small, the valve opens through the force of the pressure spring.Pressure Control Valve OpenedDiaphragm Pressure SpringTo the Intake PortS403_088If the vacuum in the intake port is too large, the pressure control valve closes.Pressure Control Valve ClosesAtmospheric PressureS403_08921Engine MechanicsDamping SectionTo prevent disruptive swirl upon introduction of the gases in the intake manifold, a damping section connects to the cyclone oil separator. In this section the motion energy of the gases from the cyclone is reduced, and a residual quantity of oil is again separated out.To the Intake PortDamping SectionS403_10422Engine MechanicsCoolant CircuitIn the coolant circuit, the coolant is circulated by a mechanical coolant pump. It is driven by the toothed belt. The circuit is controlled by an expansion-element thermostat, the coolant control unit.678324 59 1Legend 1 – Radiator 2 – Coolant Control Unit (Expansion Element Thermostat) 3 – Coolant Pump 4 - Transmission Cooler (if applicable) 5 – Oil Cooler 6 – Cooler for Exhaust Gas Return 7 – Heat Exchanger For Heater 8 – Equalizing Reservoir 9 -- Engine Block Heater (optional)The engine block heater is not planned to be available until early in 2009 and will be a dealer-installed item.23Engine MechanicsHigh and Low Pressure Exhaust Gas Recirculation (EGR) SystemThe most effective measure to reduce nitrogen oxides (NOx) with an internal combustion engine is by introducing very high exhaust gas recirculation rates into the combustion chamber. An additional advantage is to introduce these very high exhaust gases at very low temperatures. The current cooled EGR systems that exist in many applications today had to be modified. To meet BIN 5 emission standards, the entire operating characteristics of the engine up to full-load required EGR operation.Air FilterMass Airflow Sensor Cylinder pressure sensorsAirCR injectorsLow Pressure (LP) EGRCharge air cooler Throttle valve HP EGR valve Variable inlet manifold with path feedback VTG turbochargerEGR cooler valve EGR coolerExhaust High Pressure (HP) EGRDOC + DPF NOx Exhaust storage cat. valve H2S catalytic converter24Engine MechanicsThe air mass regulation of the High-Pressure EGR is regulated by the EGR Vacuum Regulator Solenoid Valve N18 and servo and by the turbocharger vane direction. The short path of the High-Pressure EGR is used in order to reach the desired EGR rate while driving at lower engine speeds and loads. The combined EGR operation is continuously adjusted depending on engine operating conditions and revolutions-per-minute (RPM). Thus, no-load engine operation results in high amounts of High Pressure EGR application.With rising engine load and engine RPM, the recirculation of exhaust gases is shifted to the Low Pressure EGR system to increase the recirculation rate. This happens in order to obtain optimal NOx reduction at middle and high engine loads. Particularly in the high engine loads, the cooled Low Pressure EGR is a very large advantage over the High Pressure EGR system.Air FilterMass Airflow Sensor Cylinder pressure sensorsAirCR injectorsLow Pressure (LP) EGRCharge air cooler Throttle valve HP EGR valve Variable inlet manifold with path feedback VTG turbochargerEGR cooler valve EGR coolerExhaust High Pressure (HP) EGRDOC + DPF NOx Exhaust storage cat. valve H2S catalytic converterUncooled EGR00125Engine MechanicsThe Fuel SystemSchematic Overview1 – Transfer Fuel Pump (FP) G6 Feeds fuel continuously in the presupply area (from the fuel tank). 2 – Fuel Filter with Preheating Valve The preheating valve prevents the filter from becoming clogged due to crystallization of paraffin in low ambient temperatures. 3 – Auxiliary Fuel Pump V393 Feeds fuel from the presupply area to the fuel pump. 4 – Filter Screen Protects the high-pressure pump from dirt particles. 5 – Fuel Temperature Sensor G81 Determines the current fuel temperature. 6 – High-Pressure Pump Generates the high fuel pressure needed for injection. 7 – Fuel Metering Valve N290 Regulates the quantity of fuel to be compressed based on demand.26Engine Mechanics8 – Fuel Pressure Regulator Valve N276 Adjusts the fuel pressure in the high-pressure area. 9 – High-Pressure Accumulator (Rail) For all cylinders, stores the fuel needed for injection under high pressure. 10 – Fuel Pressure Sensor G247 Determines the current fuel pressure in the highpressure area. 11 – Pressure Retention Valve Retains the return pressure of the fuel injectors at approximately 145 psi (10 bar). This pressure is needed for the function of the fuel injectors. 12 – Cylinder 1 through 4 Fuel Injectors N30, N31, N32, N33High Pressure 3,336 – 26,107 psi (230 – 1800 bar) Return Pressure of the Fuel Injectors 145 psi (10 bar) Presupply Pressure Return PressureS403_02127Engine MechanicsCommon Rail Injection SystemThe common rail injection system is a high-pressure accumulator injection system for diesel engines. The term “common rail” refers to the shared fuel high-pressure accumulator for all fuel injectors in a cylinder bank. In this type of injection system, pressure generation and fuel injection are performed separately. A separate high-pressure pump generates the high fuel pressure required for injection. This fuel pressure is stored in a high-pressure accumulator (rail) and supplied to the fuel injectors over short injection lines. The common rail injection system is controlled by the Bosch EDC 17 engine management system.High-Pressure Accumulator (Rail)High-Pressure PumpS403_03628Engine MechanicsThe characteristics of this injection system are: • The injection pressure is selectable and can be adapted to the operating conditions of the engine. • A high injection pressure up to a maximum of 26,107 psi (1800 bar) enables good mixture formation. • A flexible course of injection with multiple pre- and post-injections. The common rail injection system can adapt the injection pressure and the timing of the injection to the operating conditions of the engine. This system is very well suited to fulfill the constantly increasing requirements for an injection system to provide greater fuel economy, lower emissions, and quiet operation.Cylinder 1 through 4 Fuel Injectors N30, N31, N32, N33Fuel Pressure Regulator Valve N276 Fuel Pressure Sensor G247High-Pressure Accumulator (Rail) Fuel Metering ValveHigh-Pressure Pump Fuel Inlet to the HighPressure Accumulator (Rail)S403_05529Engine MechanicsFuel Injectors N30, N31, N32, N33In the common rail system of the 2.0 Liter TDI engine, piezo-controlled Fuel Injectors N30, N31, N32, and N33 are used. The fuel injectors are controlled over a piezo actuator. The switching speed of a piezo actuator is approximately four times faster than a solenoid valve. Compared to solenoid actuated fuel injectors, piezo technology also involves approximately 75% less moving mass at the nozzle pin. This results in the following advantages: • Very short switching times • Multiple injections possible per work cycle • Precise metering of injection quantitiesThrottle Plate Nozzle Spring Seal Fuel Inlet (High-Pressure Connection) Electrical ConnectionRod Filter Fuel ReturnPiezo ActuatorCoupling Piston Valve Piston Valve Piston Spring Switching ValveCourse of InjectionDue to the very short switching times of the piezocontrolled fuel injectors, it is possible to control the injection phases and quantities flexibly and precisely. This enables the course of injection to be adaptedNozzle PinS403_024to the operating conditions of the engine. Up to five partial injections can be performed per course of injection.Control Voltage (Volts)Injection (Injection Rate)Pre-Injection Main InjectionPost-InjectionS403_02530Engine MechanicsAuxiliary Fuel Pump V393The Auxiliary Fuel Pump V393 is a roller-cell pump. It is located in the engine compartment and has the task of feeding fuel from the fuel tank to the high-pressure pump. The Auxiliary Fuel Pump V393 is actuated by the Engine Control Module (ECM) J623 through a relay and increases the fuel pressure presupplied by the Transfer Fuel Pump (FP) G6 in the fuel tank to approximately 73 psi (5 bar). Effects of Failure If the Auxiliary Fuel Pump V393 fails, the engine runs at first with reduced power. An engine startup is not possible.Auxiliary Fuel Pump V393S403_058From the Fuel Tank Auxiliary Fuel Pump V393To the High-Pressure PumpElectrical ConnectionsS403_037Filter ScreenTo protect the high-pressure pump from dirt particles, a filter screen is installed before the high-pressure pump in the fuel inlet.FilterS403_09431Engine MechanicsHigh-Pressure PumpThe high-pressure pump is a single-piston pump. It is driven via the toothed belt by the crankshaft at engine speed. The high-pressure pump has the job of generating the high fuel pressure of up to 26,107 psi (1800 bar) needed for injection. Pressure is generated by the rotation of two cams offset by 180 degrees on the pump drive shaft. The injection is always in the operating cycle of the respective cylinder. This keeps the pump drive evenly loaded and pressure fluctuations in the high-pressure area are minimized.Design of the High-Pressure PumpFuel Metering Valve N290 Intake Valve Exhaust Valve Connection to the Rail Pump Piston Fuel InletPiston Spring Fuel ReturnRollerOverflow ValveDrive ShaftDrive CamS403_02732Engine MechanicsWhen setting the control times of the engine, the position of the high-pressure pump drive shaft must be set. Please refer to the instructions in the Repair Manual.Design of the High-Pressure Pump – SchematicIntake Valve Exhaust ValveFuel Metering Valve N290 Connection to the RailPump Piston Piston Spring Fine FilterRoller Overflow ValveDrive Shaft with CamFuel Return Fuel InletS403_04933Engine MechanicsHigh-Pressure Area The high-pressure pump is supplied with adequate fuel by the Auxiliary Fuel Pump V393 in each operating range of the engine. The fuel enters the high-pressure area of the engine through the Fuel Metering Valve N290. The pump piston is moved upward and downward by the cams on the pump drive shaft.Exhaust ValveConnection to the High-Pressure Accumulator (Rail)Fuel Metering Valve N290Pump PistonDrive Shaft with Cam Fuel Inlet of the Auxiliary Fuel PumpS403_10734Engine MechanicsIntake Stroke The downward motion of the pump piston increases the volume the compression space. This results in a pressure differential between the fuel in the high-pressure pump and the compression space.The intake valve opens and fuel flows into the compression space.Intake ValveCompression SpacePump PistonS403_10835Engine MechanicsDelivery Stroke With the beginning of the upward motion of the pump piston, the pressure in the compression space increases and the intake valve closes.As soon as the fuel pressure in the compression space exceeds the pressure in the high-pressure area, the exhaust valve (check valve) opens and fuel enters the high-pressure accumulator (rail).Connection to the HighPressure Accumulator (Rail)Exhaust ValvePump PistonS403_10936Engine MechanicsFuel Metering Valve N290Fuel Metering Valve N290 is integrated in the highpressure pump. It ensures demand-based control of the fuel pressure in the high-pressure area. The Fuel Metering Valve N290 controls the fuel quantity that is needed for high-pressure generation. This represents an advantage, in that the high-pressure pump must generate only the pressure needed for the momentary operating situation. The power consumption of the high-pressure pump is reduced and unnecessary warming up of the fuel is avoided. Function The non-energized state the Fuel Metering Valve N290 is open. To reduce the feed quantity to the compression space, the valve is actuated by the Engine Control Module (ECM) J623 with a pulsewidth modulated (PWM) signal. Through the PWM signal the Fuel Metering Valve N290 is closed cyclically. Depending on the duty cycle, the position of the locking piston changes as does the amount of fuel into the compression space of the high-pressure pump. Effects of Failure Engine power is reduced. Engine management operates in emergency mode.To the Compression SpaceFeed from Pump InteriorS403_11037Engine MechanicsLow-Pressure AreaOverflow Valve The fuel pressure in the low-pressure area of the high-pressure pump is controlled by the overflow valve. Function The Auxiliary Fuel Pump V393 delivers fuel from the fuel tank with a pressure of approximately 73 psi (5 bar) into the high-pressure pump. Thus the fuel supply to the high-pressure pump is ensured in all operating conditions. The overflow valve regulates the fuel pressure in the high-pressure pump to approximately 62 psi (4.3 bar). The fuel delivered by the Auxiliary Fuel Pump V393 acts in opposition to the piston and the piston spring of the overflow valve. With a fuel pressure over 62 psi (4.3 bar), the overflow valve opens and clears the way to the fuel return. The excess fuel flows through the fuel return into the fuel tank.Overflow ValveFuel Return Fuel PresupplyS403_11138Engine MechanicsControl of the Fuel High PressureIn the common rail injection system, the fuel high pressure is controlled by a so-called two-controller concept. Depending on the operating conditions, the high fuel pressure is regulated either by the Fuel Pressure Regulator Valve N276 or the Fuel Metering Valve N290. The valves are actuated by the Engine Control Module (ECM) J623 with a pulse-width modulated (PWM) signal. Control by the Fuel Pressure Regulator Valve N276 At engine start and for preheating of the fuel, the high fuel pressure is controlled by the Fuel Pressure Regulator Valve N276. To heat up the fuel quickly, the high-pressure pump delivers and compresses more fuel than is needed. The excess fuel is discharged by the Fuel Pressure Regulator Valve N276 into the fuel return. Control by the Fuel Metering Valve N290 With large injection quantities and high rail pressures, the high fuel pressure is controlled by the Fuel Metering Valve N290. This effects a demand-based regulation of the fuel high pressure. The power consumption of the high-pressure pump is reduced and unnecessary heating up of the fuel is avoided. Control by Both Valves In idling, in trailing throttle condition, and with small injection quantities, the fuel pressure is controlled by both valves simultaneously. This enables precise control, which improves idling quality and the transition into trailing throttle condition.Two-Controller ConceptInjection QuantityControl of Fuel High Pressure by Fuel Pressure Regulator Valve N276 Control of Fuel High Pressure by Fuel Metering Valve N290 Control by Both ValvesEngine SpeedS403_03039Engine MechanicsFuel Pressure Regulator Valve N276The Fuel Pressure Regulator Valve N276 is located on the high-pressure accumulator (rail). Opening and closing of the Fuel Pressure Regulator Valve N276 adjusts the pressure of the fuel in the high-pressure area. This is actuated by the Engine Control Module (ECM) J623 with a pulse-width modulated signal.Fuel Pressure Regulator Valve N276S403_023DesignSolenoid Coil High-Pressure Accumulator (Rail) Valve NeedleElectrical ConnectionValve AnchorValve SpringReturn to Fuel TankS403_03240Engine MechanicsHow it Works In contrast to conventional control valves in common rail injection systems, the Fuel Pressure Regulator Valve N276 is open in the non-energized state. Fuel Pressure Regulator Valve N276 in Rest Position (Engine “Off”) If the Fuel Pressure Regulator Valve N276 is not activated, the pressure regulator valve is opened by the valve springs. The high-pressure area is connected to the fuel return. This ensures volume compensation between the high-pressure and low-pressure areas. Fuel vapor lock, which can occur during the cool-down with engine standstill in the high-pressure accumulator (rail), is avoided and the startup properties of the engine are improved.S403_033Valve SpringsFuel Pressure Regulator Valve N276 Activated (Engine “On”) To set an operating pressure of 3,336 to 26,107 psi (230 to 1800 bar) in the high-pressure accumulator, the Fuel Pressure Regulator Valve N276 is actuated by the Engine Control Module (ECM) J623 with a pulse-width modulated (PWM) signal. Upon actuation a magnetic field is generated in the solenoid coil. The valve anchor is tightened and presses the valve needle into its seat. A magnetic force opposes the fuel pressure in the high-pressure accumulator. Depending on the duty cycle of the actuation, the flow cross-section to the return line and the exhaust quantity is changed. This also allows fluctuations in the pressure in the high-pressure accumulator to be compensated. Effects of Failure If the Fuel Pressure Regulator Valve N276 fails, the engine cannot run because adequate high fuel pressure cannot be developed for injection.S403_03441Engine Management SystemEngine Management SystemSystem OverviewSensorsEngine Speed (RPM) Sensor G28 Camshaft Position (CMP) Sensor G40 Throttle Position (TP) Sensor G79 / Accelerator Pedal Position Sensor 2 G185 Mass Air Flow (MAF) Sensor G70 Engine Coolant Temperature (ECT) Sensor G62 Charge Air Pressure Sensor G31 Intake Air Temperature (IAT) Sensor G42 Manifold Absolute Pressure (MAP) Sensor G71 Fuel Temperature Sensor G81 Fuel Pressure Sensor G247 EGR Potentiometer G212 Heated Oxygen Sensor (HO2S) G39 Exhaust Pressure Sensor 1 G450 Low Pressure Exhaust Gas Recirculation (EGR) Pressure Sensor Exhaust Gas Temperature (EGT) Sensor 1 G235 Exhaust Gas Temperature (EGT) Sensor 2 G448 Exhaust Gas Temperature (EGT) Sensor 3 G495 Exhaust Gas Temperature (EGT) Sensor 4 G648 Exhaust Gas Recirculation (EGR) Temperature Sensor G98 Engine Coolant Temperature (ECT) Sensor (on radiator) G83 Oxygen Sensor (O2S) Behind Three Way Catalytic Converter (TWC) G130 Brake Light Switch F Clutch Position Sensor G476 Charge Pressure Actuator Position Sensor G581 Intake Manifold Runner Position Sensor G336 Cylinder Pressure Sensors G620 - G623 Throttle Position (TP) Sensor G69 Instrument Cluster Control Module J285 Glow Plug Indicator Lamp K29Diesel Particle Filte Indicator Lamp K23 Malfunction Indicator Lamp (MIL) K8342Engine Management SystemActuatorsFuel Pump (FP) Relay J17 Transfer Fuel Pump (FP) G6 CAN Data Bus Drive Auxiliary Fuel Pump Relay J832 Auxiliary Fuel Pump V393 Cylinder 1 Fuel Injector N30 Cylinder 2 Fuel Injector N31 Cylinder 3 Fuel Injector N32 Cylinder 4 Fuel Injector N33 Fuel Metering Valve N290er 31Fuel Pressure Regulator Valve N276 Wastegate Bypass Regulator Valve N75 (uses variable turbine geometry)Intake Flap Motor V157 Engine Control Module (ECM) J623Throttle Valve Control Module J338 Exhaust Flap Control Module J883 With Position SensorEGR Vacuum Regulator Solenoid Valve N18Exhaust Gas Recirculation (EGR) Cooler Switch-Over Valve N345 EGR Valve 2 N213Engine Coolant (EC) Circulation Pump 2 V178 Oxygen Sensor (O2S) Heater Z19 Oxygen Sensor (O2S) Heater Z28 Automatic Glow Time Control Module J179 Glow Plug 1 Q10 Glow Plug 2 Q11 Glow Plug 3 Q12 Glow Plug 4 Q13S403_02843Engine Management SystemElectronic Diesel Control (EDC) Engine ManagementThe engine management system of the 2.0 Liter TDI engine with common rail injection system is the electronic diesel control EDC17 from Bosch. The EDC17 engine management system is the successor of EDC16. EDC17 has greater processing capability and a larger storage capacity than EDC16. It also offers the option of integrating control functions for future technologies.Control Devices in the CAN Data BusThe schematic below shows the integration of the Engine Control Module J623 into the CAN data bus structure of the vehicle. Information is transmitted between control devices over the CAN data bus.Engine Control Module J623S403_052Color Codes CAN Data Bus Drive CAN Data Bus Comfort CAN Data Bus InfotainmentS403_090Legend J104 ABS Control Module J217 Transmission Control Module (TCM) J234 Airbag Control Module J285 Instrument Cluster Control Module J519 Vehicle Electrical System Control ModuleJ527 Steering Column Electronic Systems Control Module J533 Data Bus On Board Diagnostic Interface J623 Engine Control Module (ECM)44Engine Management SystemExhaust Gas TurbochargerThe boost pressure in the 2.0 Liter TDI engine is generated by an adjustable turbocharger. It has adjustable guide vanes that can be used to influence the flow of exhaust gas onto the turbine wheel. The advantage is that optimum boost pressure and good combustion are achieved over the entire engine speed range. The adjustable guide vanes ensure high torque and good starting behavior in the lower speed range, as well as low fuel consumption and low exhaust gas emissions in the upper speed range. A linkage controlled by vacuum is used to adjust the guide vanes.Charge Pressure Actuator Position Sensor G581 Exhaust Gas TurbochargerFlow Damper821803_026baFlow DamperA flow damper is located behind the outlet of the turbocharger in the charge air section. It has the task of reducing disagreeable noise from the turbocharger, such as whistling. Design and Function During full-load acceleration the turbocharger must build up boost pressure very quickly. The turbine and compressor wheel are accelerated quickly and the turbocharger approaches its pump limit. This can lead to burbling in the air flow, which causes disturbing noise that radiates into the charge air section. The charge air causes the air in the resonance sections of the flow damper to vibrate. The vibration has approximately the same frequency as the noise in the charge air. Disturbing noise is minimized by superimposition of the charge air sound waves with the vibration of the air in the resonance sections ofResonance SectionsCharge Air from the TurbochargerS403_09845Engine Management SystemBoost Pressure ControlThe boost pressure control manages the volume of air that is compressed by the turbocharger.2 36 4 7 10 8 5 11 19Legend 1 – Vacuum System 2 – Engine Control Module (ECM) J623 3 – Intake Air 4 – Charge Air Cooler 5 – Vacuum Regulator Valve 6 – Turbocharger Compressor 7 – Actuator / Guide Vane Position Sensor 8 – Exhaust Gas Turbine with Guide Vane Adjuster 9 – Diesel Particulate Filter / Oxidation Catalyst 10 – Charge Air Pressure Sensor G31 and Intake Air Temperature (IAT) Sensor G42 11 – Low Pressure EGR Valve46Engine Management SystemWastegate Bypass Regulator Valve N75The Wastegate Bypass Regulator Valve N75 is an electro-pneumatic valve. This valve is used to control the vacuum needed to adjust the guide vanes over the vacuum cell. Effects of Failure If the Wastegate Bypass Regulator Valve N75 fails the vacuum cell is not supplied with vacuum. A spring in the vacuum cell pushes the linkage of the adjusting mechanism so that the guide vanes of the turbocharger are brought into a steep approach angle (emergency mode position). With lower engine speed and thus lower exhaust gas pressure, only a low boost pressure is available. The engine has less power, and an active regeneration of the particulate filter is not possible.Wastegate Bypass Regulator Valve N75S403_09747Engine Management SystemCylinder Pressure SensorsA cylinder pressure sensor is integrated into each of the Glow Plugs. The glow element is attached to an extension, which can apply pressure to a diaphragm. The diaphragm has strain gauges that change resistance by deformation. The integrated electronics calculate tension, which is proportional to the combustion chamber pressure. Effect of Failure If one of the pressure sensors fails, a substitute value will be used from the other pressure sensors.Signal Use The pressure sensor collects cylinder burn-data such as the burn moment and the situation of the burn in relation to the crankshaft. This can result in an increase or decrease of the injection amount, as the pressure is indirectly related to the injection amount. Correcting the injection using pressure sensor information balances the injection for all cylinders. In addition, this correction applies to manufacturing tolerances and engine aging. As a direct result of the pressure sensors, emission tolerances are clearly reduced over the life span of the engine. The regulation of the burn is accomplished by shifting the start of injection. Thus, the burn stabilizes during times of very large exhaust recirculation rates and misfires and other running issues can be avoided. Also, the pressures can help to balance the time delays caused by bad fuel (low Cetane).48Engine Management SystemPressure Sensor Power Pressure Sensor Ground Pressure Sensor Signal Glow Plug Power Glow Plug / Pressure Sensor ConnectorElectrical ChipMembrane with Strain Gauges Glow Rod, Moveable by Approx 4mmMetal Sealing Bellows49Engine Management SystemCharge Air Pressure Sensor G31 and Intake Air Temperature (IAT) Sensor G42Charge Air Pressure Sensor G31 and Intake Air Temperature (IAT) Sensor G42 are integrated in one component and are located in the intake manifold.Intake Air Temperature (IAT) Sensor G42Engine Control Module (ECM) J623 uses the signal of Intake Air Temperature (IAT) Sensor G42 to control the boost pressure. Because the temperature influences the density of the charge air, the signal is used by Engine Control Module (ECM) J623 as a correction value.Charge Air Pressure Sensor G31Signal Use The air pressure in the intake manifold is determined from the Charge Air Pressure Sensor G31 signal. Engine Control Module (ECM) J623 needs the signal to control the boost pressure. Effect of Failure If the Charge Air Pressure Sensor G31 signal fails, there is no substitute function. The boost pressure control is disengaged and the engine power decreases significantly. The particulate filter cannot be actively regenerated.Charge Air Pressure Sensor G31 Intake Air Temperature (IAT) Sensor G42Charge Air CoolerS403_09650Engine Management SystemCharge Pressure Actuator Position Sensor G581Charge Pressure Actuator Position Sensor G581 is integrated in the vacuum cell of the turbocharger. It is a displacement sensor that enables Engine Control Module (ECM) J623 to determine the position of the guide vanes in the turbocharger. Signal Use The signal of Charge Pressure Actuator Position Sensor G581 delivers the position of the guide vanes of the turbocharger to Engine Control Module (ECM) J623. Together with the signal of Charge Air Pressure Sensor G31, this allows conclusions about the state of boost pressure control. Effects of Failure If Charge Pressure Actuator Position Sensor G581 fails, the signal from Charge Air Pressure Sensor G31 and the engine speed are used to determine the position of the guide vanes. Malfunction Indicator Lamp (MIL) K83 is actuated.Charge Pressure Actuator Position Sensor G581S403_09551Engine Management SystemEGR Vacuum Regulator Solenoid Valve N18The EGR Vacuum Regulator Solenoid Valve N18 is an electric motor controlled valve plate. It is actuated by the Engine Control Module (ECM) J623 and can be infinitely adjusted by the electric motor. The angle of the valve plate controls the quantity of returned exhaust gas. Effect of Failure If EGR Vacuum Regulator Solenoid Valve N18 fails, the valve plate is closed by a valve spring. No exhaust gas can be returned.EGR Potentiometer G212EGR Potentiometer G212 captures the position of the valve plate in the exhaust gas return valve. Signal Use Based on the signal, Engine Control Module (ECM) J623 recognizes the position of the valve plate. This enables control of returned exhaust gas volume and thus the nitrogen oxide content in the exhaust gas. Effect of Failure If EGR Potentiometer G212 fails, the exhaust gas return is deactivated. The EGR Vacuum Regulator Solenoid Valve N18 drive is switched to the nonenergized state and the valve plate is closed by a valve spring.Exhaust Gas Return Valve with EGR Potentiometer G212 and EGR Vacuum Regulator Solenoid Valve N18S403_09952Engine Management SystemLow Pressure Exhaust Gas Recirculation (EGR) Valve with EGR Potentiometer and EGR Valve N345The exhaust gas return cooler is a switchable cooler that allows the engine and diesel particulate filter to reach their operating temperatures more quickly. The exhaust gas cooler is activated when the coolant temperatures reach 99ºF (37ºC) The Exhaust Gas Recirculation (EGR) Cooler SwitchOver Valve N345 is an electrically-controlled valve plate . It is actuated by the Engine Control Module (ECM) J623 and can be infinitely adjusted by the electric motor. The position of the valve plate controls the quantity of the returned exhaust gas. Effect of Failure If the Exhaust Gas Recirculation (EGR) Cooler SwitchOver Valve N345 fails, the valve plate is closed by a spring. No exhaust gas can be returned.To the Intake Side of the TurbochargerIMG_0408_edit3Low Pressure Exhaust Gas Recirculation Valve with EGR Potentiometer and EGR Valve N345EGR PotentiometerThe EGR Potentiometer captures the position of the valve plate in the Low Pressure exhaust gas recirculation valve.Signal Use Based on the signal, the Engine Control Module (ECM) J623 recognizes the position of the valve plate. This enables control of the returned exhaust gas volume and thus the nitrogen oxide content in the exhaust gas.Effect of Failure If the EGR potentiometer fails, the Low Pressure recirculation is deactivated. The Low Pressure EGR Vacuum Regulator Solenoid Valve N345 drive is switched to the non-energized state and the valve plate is closed by the valve spring53Engine Management SystemThrottle Valve Control Module J338In the direction of flow, Throttle Valve Control Module J338 is mounted before EGR Vacuum Regulator Solenoid Valve N18. There is an electric motor in Throttle Valve Control Module J338 that moves the throttle with a gear. Adjustment of the throttle is infinite and can be adapted to the respective load and speed of the engine. The Throttle Valve Control Module J338 has the following tasks: In certain operating situations, a differential between intake manifold pressure and exhaust gas pressure is generated through the throttle. This pressure differential facilitates exhaust gas return. In the regeneration mode of the diesel particulate filter, the intake air volume is regulated with the throttle. When the Throttle Valve Control Module J338 motor is switched off, the throttle is closed. Less air is taken in and compressed, and the engine shuts down smoothly. Effect of Failure If Throttle Valve Control Module J338 fails, correct regulation of the exhaust gas return rate is not possible. An active regeneration of the diesel particulate filter does not take place.Throttle Valve Control Module J338 with Throttle Position (TP) Sensor G69S403_101Throttle Position (TP) Sensor G69Throttle Position (TP) Sensor G69 is integrated in the throttle drive. The sensor element captures the position of the throttle. Signal Use Based on the signal, Engine Control Module (ECM) J623 recognizes the position of the throttle. This information is needed for control of exhaust gas return and particulate filter regeneration.Effect of Failure If Throttle Position (TP) Sensor G69 fails, the exhaust gas return is deactivated and active regeneration of the diesel particulate filter does not take place.54Engine Management SystemExhaust Throttle ValveThe exhaust throttle valve is a new component. In the direction of exhaust flow, the Exhaust Throttle Valve is located behind the NOx storage catalytic converter. There is an electric motor inside of the Exhaust Throttle Valve that moves the throttle plate with a gear. Adjustment of the throttle plate is infinite and can be adapted to respective load and speed of the engine. The Exhaust Throttle Valve has the following tasks: • In certain operating conditions, a differential pressure is generated between the NOx storage catalyst and the turbocharger. • This increase in pressure helps with Low Pressure EGR return. Effect of Failure If the Throttle Valve Control Module fails, the correct regulation of exhaust gas recirculation rate is not possible. Regeneration of the NOx storage catalyst does not take place.Throttle Valve with Throttle Position (TP) SensorThe throttle Position Sensor is integrated into the throttle valve drive. The purpose of this sensor is to capture the position of the throttle valve. Signal Use Based on the signal, Engine Control Module (ECM) J623 recognizes the position of the throttle. This information is needed for control of exhaust gas recirculationEffect of Failure If Throttle Position (TP) Sensor G69 fails, the exhaust gas recirculation is deactivated.55Engine Management SystemExhaust SystemThe exhaust system of the 2.0L Common-Rail is very different from previous engines. The exhaust system consists of the following main components: • Oxidation Catalytic Converter • Particulate Filter • Nitrogen Oxide Catalytic Converter • H2S Catalytic ConverterOxidation Catalytic ConverterDiesel Particulate FilterH2S Catalytic ConverterNitrogen Oxide Catalytic ConverterLow Pressure EGR Filter56Engine Management SystemDiesel Particulate Filter SystemIn addition to internal engine measures in the 2.0 Liter TDI engine with common rail injection system, soot particle emissions are further reduced through a diesel particulate filter. The diesel particulate filter is found together with the oxidation catalyst in a housing. It is located close to the engine so that it will reach operating temperature quickly.Differential Pressure Sensor Pipes Differential Pressure Sensor Pipes Oxygen SensorDiesel Particulate Filter (DPF)Temperature SensorsS403_05457Engine Management SystemDiesel Particulate Filter and NOx Storage Catalytic Converter System Overview1102 11 3 4 7129 13 5 6 8 14Legend 1 – Mass Air Flow (MAF) Sensor G70 2 – Exhaust Gas Temperature (EGT) Sensor 1 G235 3 – Turbocharger 4 – Heated Oxygen Sensor (HO2S) G39 5 – Oxidation Catalyst 6 – Particulate Filter 7 – Exhaust Gas Temperature (EGT) Sensor 3 G495 8 – Exhaust Pressure Sensor 1 G450 9 – Exhaust Gas Temperature (EGT) Sensor 4 G648 10 – Cylinder Pressure Sensors 1,2,3,4 11 – Low Pressure EGR Temperature Sensor 12 – Low Pressure EGR Potentiometer 13 - Exhaust Gas Temperature (EGT) Sensor 2 14 - Heated Oxygen Sensor (H02S) G130Additional Components not Pictured: - Low Pressure EGR Differential Pressure Sensor - Wastegate Bypass Regulator Valve N7558Engine Management SystemDiesel Particulate Filter System DesignThe diesel particulate filter and the oxidation catalyst are installed separately in a shared housing. The oxidation catalyst is located before the particulate filter in the direction of flow. This design with the oxidation catalyst upstream offers the following advantages in connection with the common rail injection system: • Because of the upstream placement of the oxidation catalyst, the temperature of the exhaust gas is increased before it enters the diesel particulate filter. As a result, the operating temperature of the diesel particulate filter is reached quickly. • In trailing throttle condition, over cooling of the diesel particulate filter by the cold intake air is prevented. In this case, the oxidation catalyst acts as a heat exchanger, from which the warmth is routed through the exhaust gas flow to the particulate filter. • In the regeneration operation, the temperature of the exhaust gas is accurately controlled. The Exhaust Gas Temperature (EGT) Sensor 3 G495 determines the temperature of the exhaust gas directly before the particulate filter. As a result, the fuel quantity of the post-injection is precisely calculated to increase the exhaust gas temperature in the regeneration operation.Heated Oxygen Sensor (HO2S) G39Exhaust Gas Temperature (EGT) Sensor 3 G495Oxidation CatalystExhaust Gas FlowDiesel Particulate FilterExhaust Gas Temperature (EGT) Sensor 4 G648Connection for Exhaust Pressure Sensor 1 G450S403_09159Engine Management SystemOxidation CatalystThe carrier material of the oxidation catalyst is metal, so the light-off temperature is reached quickly. This metal body has an aluminum oxide carrier coating, onto which platinum and palladium are vapordeposited as catalyst for the hydrocarbons (HC) and the carbon monoxide (CO). Function The oxidation catalyst converts a large portion of the hydrocarbons (HC) and the carbon monoxide (CO) into water vapor and carbon dioxide. Diesel Particulate Filter The diesel particulate filter consists of a honeycombshaped ceramic body made of aluminum titanide. The ceramic body is partitioned into a large number of small channels, which are alternately open and closed at the ends. This results in inlet and outlet channels that are separated by filter walls. The filter walls are porous and coated with a carrier coating of aluminum oxide. Vapor-deposited onto this carrier layer is the precious metal platinum, which acts as catalyst. Function As the soot-containing exhaust gas flows through the porous filter walls of the inlet channels, the soot particles are captured in the inlet channels.S403_07260Engine Management SystemRegenerationThe particulate filter must be regenerated regularly so that it does not become clogged with soot particles and its function impaired. During regeneration, the soot particles collected in the particulate filter are burned off (oxidized). The regeneration of the particulate filter is performed in the following stages: • Warm-up phase • Passive regeneration • Active regeneration • Customer-initiated regeneration drive • Service regeneration Warm-Up Phase To heat up a cold oxidation catalyst and particulate filter as quickly as possible and thus bring them to operating temperature, the engine management system introduces a post-injection after the main injection. This fuel combusts in the cylinder and increases the combustion temperature. Through the air flow in the exhaust gas tract, the resulting heat reaches the oxidation catalyst and the particulate filter and heats them. The warm-up phase is complete when the operating temperature of the oxidation catalyst and the particulate filter has been reached for a specific period of time. Passive Regeneration During passive regeneration the soot particles are continuously burned without the intervention of Engine Control Module (ECM) J623. This occurs primarily at higher engine load, such as in highway driving, when exhaust gas temperatures range from 662°F to 932°F (350°C to 500°C). At these temperatures the soot particles are converted into carbon dioxide through a combustion reaction with nitrogen dioxide.61Engine Management SystemActive RegenerationIn a large portion of the operating range the exhaust gas temperatures are too low for a passive regeneration. Because soot particles can no longer be eliminated passively, soot accumulates in the filter. As soon as a specific soot load has been reached in the filter, the Engine Control Module (ECM) J623 initiates an active regeneration. The soot particles are burned off at an exhaust gas temperature of 1022°F to 1202°F (550°C to 650°C). Active Regeneration Function The soot load of the particulate filter is calculated by two pre-programmed load models in the Engine Control Module (ECM) J623. One of the load models is determined from the driving profile of the user and the signals from the exhaust gas temperature sensors and Heated Oxygen Sensor (HO2S) G39. Another soot load model is the flow resistance of the particulate filter. It is calculated from the signals of Exhaust Pressure Sensor 1 G450, Exhaust Gas Temperature (EGT) Sensor 3 G495, and Mass Air Flow (MAF) Sensor G70.Mass Air Flow (MAF) Sensor G70Exhaust Pressure Sensor 1 G450 Exhaust Gas Temperature (EGT) Sensor 3 G495Engine Control Module (ECM) J623Heated Oxygen Sensor (HO2S) G39Oxidation CatalystDiesel Particulate FilterS403_07062Engine Management SystemEngine Control Module (ECM) J623 has several ways to control the increase of exhaust gas temperatures during active regeneration: • The intake air supply is regulated by Throttle Valve Control Module J338.S403_074• The exhaust gas return is deactivated to increase the combustion temperature and the oxygen content in the combustion chamber.S403_075• Shortly after a delayed “late” main injection, the first post-injection is initiated to increase the combustion temperature.S403_076• Late after the main injection an additional postinjection is initiated. This fuel does not combust in the cylinder, but instead vaporizes in the combustion chamber.S403_077• The unburned hydrocarbons of this fuel vapor are oxidized in the oxidation catalyst. This ensures an increase in the exhaust gas temperature to approximately 1202°F (650°C) as it reaches the particulate filter.S403_078• To calculate the injection quantity for the late post-injection, Engine Control Module (ECM) J623 uses the signal of Exhaust Gas Temperature (EGT) Sensor 3 G495 located before the particulate filter.S403_080• The boost pressure is adjusted so that the torque during the regeneration operation does not change noticeably for the driver.S403_07963Engine Management SystemCustomer-Initiated Regeneration DriveAn exhaust gas temperature high enough for particulate filter regeneration is not reached when the vehicle is only driven for short-distances. If the load condition of the diesel particulate filter reaches a threshold value, Diesel Particle Filter Indicator Lamp K231 in the instrument panel will light up. This signal prompts the driver to perform a regeneration drive. The vehicle must be driven for a short period of time at increased speed to ensure that an adequately high exhaust gas temperature is reached. The operating conditions must remain constant over the period for a successful regeneration. Details of the driving behavior required when the Diesel Particle Filter Indicator Lamp K231 comes on can be found in the Owner’s Manual.Service RegenerationIf the regeneration drive is not successfully completed and the load condition of the diesel particulate filter has reached 1.41 ounces (40 grams), Diesel Particle Filter Indicator Lamp K231 and Glow Plug Indicator Lamp K29 will light up simultaneously. The text “Check Engine – Service Shop” will appear in the instrument panel display. This prompts the driver to visit the nearest service shop. In this case, the Engine Control Module (ECM) J623 blocks active regeneration of the diesel particulate filter to prevent damage to the filter and the particulate filter can only be regenerated by service regeneration with the VAS 5051. When the load condition reaches 1.59 ounces (45 grams), service regeneration is no longer possible. Because the danger of destroying the filter is too great with this load, the filter must be replaced.64Engine Management SystemRegeneration of the 2.0 Liter TDI Particulate FilterFilter ReplacementLoad in GramsTime Example: Increase in soot load Example: Profile with successful regeneration in the respective stage Passive Regeneration Active Regeneration Customer-Initiated Regeneration Drive Service Generation Filter ReplacementS403_105Distance Regeneration “Distance regeneration” is a distance-dependent regeneration of the particulate filter. The Engine Control Module (ECM) J623 initiates an active regeneration automatically if during the last 466 to 621 miles (750 to 1000 km) of travel no successful regeneration has taken place, regardless of the load condition in the diesel particulate filter. Distance regeneration serves as additional safeguard to minimize the load condition of the diesel particulate filter.65Engine Management SystemNitrogen Oxide Catalytic ConverterTo attain the BIN5/LEV2 emission level, an efficient system for exhaust gas after-treatment is required. The NOx storage catalyst is used to supplement the particulate filter system.By placing the NOx storage catalytic converter away from the engine in the vehicle underbody, the thermal aging is considerably reduced. This also takes advantage that the CO and HC that have already been oxidized by the particulate filter. This allows an optimum NOx conversion in the NOx catalytic converter.Oxidation Catalytic ConverterDiesel Particulate Filter66Engine Management SystemThe exhaust system has two lambda sensors. The lambda sensor upstream of the oxidation catalytic converter regulates the air-reduced operating modes for the NOx catalytic converter. It is also used for the initial value for the air model stored in the engine control unit. This air model help to determine the model-based NOx and soot emissions of the engine.The second lambda sensor, which is placed downstream of the NOx catalytic converter, detects an excess of reduction medium in the regeneration phase. This is used to determine loading and the aging condition of the NOx catalytic converter. The three temperature sensors integrated into the exhaust system enable the OBD functions for the catalytic components and are used as initial values in the regulation of the regeneration operating modes ad the exhaust temperature model.Sulfur Catalytic ConverterNitrogen Oxide Catalytic Converter67Engine Management SystemAdditional Engine Operating Modes for Exhaust AfterTreatmentDeNox ModeThe enhancement of the exhaust after-treatment system with a NOx storage catalytic converter requires the introduction of new regeneration modes to ensure NOx conversion throughout the storage unit’s service life. Unlike particulate filter regeneration, a substoichiometric exhaust gas composition is necessary for the regeneration of the NOx storage catalytic converter. In sub-stoichiometric operation, the nitrogen oxides stored during the lean operation are reduced by the exhaust enriched reduction media consisting of HC, CO and H2.68Engine Management SystemDeSOx ModeA further regeneration mode is provided by the sulphur removal of the NOx storage catalytic converter (DeSOx Mode). This is necessary as the sulphur contained in the fuel causes sulfate formation which slowly deactivates the NOX storage catalytic converter. The de-sulphurization procedure is designed for a sulfur content of 15 ppm parts per million (ppm) Due to the high thermal stability of the sulfates, significant levels of sulphur reduction are only possible at temperatures above 620 C (1150 F). The sulphur reduction procedure has been designed so that the storage capacity of the catalytic converter can mostly be restored without irreversible damage to the storage material. The sub-stoichiometric mode is very demanding in terms of engine management. To be able to set air mass and exhaust gas recirculation independently on each other, two separate control circuits are used. The air mass is set using the intake manifold throttle valve. The exhaust recirculation rate is set using a new, model-based regulation concept.Air FilterMass Airflow Sensor Cylinder pressure sensorsAirCR injectorsLow Pressure (LP) EGRCharge air cooler Throttle valve HP EGR valve Variable inlet manifold with path feedback VTG turbochargerEGR cooler valve EGR coolerExhaust High Pressure (HP) EGRDOC + DPF NOx Exhaust storage cat. valve H2S catalytic converter69Engine Management SystemA suitable combination of high pressure and low pressure EGR, with corresponding compression temperatures, enable stable rich operation even in the low load range with the fuel qualities that are typical for the USA.In addition to this, the injection strategy for the rich mode is changed. Up to six injections are used depending on characteristic values to attain a stable and low-soot combustion. This is particularly important in the sulphur reduction process to prevent soot accum