TECHNICAL DOCUMENTATION
SSP 924603 The 3,2 and 3,6 liter FSI Engine

This PDF is currently unavailable.
Read document text
Service TrainingThe 3.2 and 3.6 liter FSI Engine Self Study Program 924603Audi of America, Inc. Service Training Printed in U.S.A. Printed 10/2006 Course Number 924603©2006 Audi of America, Inc. All rights reserved. All information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, Inc. Always check Technical Bulletins and the latest electronic repair information for information that may supersede any information included in this booklet. Trademarks: All brand names and product names used in this manual are trade names, service marks, trademarks, or registered trademarks; and are the property of their respective owners.iiTable of ContentsOverview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Engine Mechanics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5The Crank Assembly............................................................................................... 5 The Cylinder Head. .................................................................................................. 8 Camshaft Adjustment. ........................................................................................... 9 Internal Exhaust Gas Recirculation..................................................................... 10 Crankcase Ventilation........................................................................................... 11 The Intake Manifold.............................................................................................. 13 The Chain Drive..................................................................................................... 16 The Ribbed V-belt Drive. ....................................................................................... 17 Oil Circulation. ....................................................................................................... 18 Coolant Circulation............................................................................................... 21 The Exhaust System............................................................................................. 23 FSI Technology...................................................................................................... 24Engine Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30System Overview.................................................................................................. 30 Sensors.................................................................................................................. 32 Actuators............................................................................................................... 43 The Control Modules in the CAN Data-Bus........................................................ 49Operating Diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Actuators............................................................................................................... 55Knowledge Assessment . . . . . . . . . . . . . . . . . . . . . . . . . . . 57The Self-Study Program provides introductory information regarding the design and function of new models, automotive components or technologies. The Self-Study Program is not a Repair Manual! All values given are intended as a guideline only and refer to the software version valid at the time of publication of the SSP. For maintenance and repair work, always refer to the current technical literature.iiiReferenceNoteivOverviewThe 3.2L and the 3.6L V6 FSI engines belong to the narrow V familly of engines. Their reduced V-angle, compared with a traditional V-engine, gives them an extremely compact and space-saving design. The 3.2L narrow V6 engine was first introduced to Audi in the the TT and later the A3. This narrow V engine design is highly desirable for use in smaller vehicles due to the compact design.S360_401OverviewS360_402The 3.2L and 3.6L V6 FSI engines are the newest representatives of the narrow V familly of engines. While the 3.2L version was first introduced in the Audi TT, the 3.6L FSI version is making its debut in the Audi Q7. The displacement was increased from 3.2 liters to 3.6 liters, combined with the switch to the FSI technology. This yields a noticeable increase in power and torque compared with the 3.2L engine. The 3.6L FSI engine has a maximum rated power of 280 hp (206 kW) and produces a maximum torque of 265 lb.fts (360 Nm). These two compact engines have substantial reserves of power on the road and a dynamic torque curve.Special features of both engines:• Retention of external dimensions • FSI direct gasoline injection • Four-valve technology with roller rocker arms • Internal exhaust gas recirculation • Single-piece variable-length intake manifold made of plastic • Weight-reduced cast iron crankcase • Chain drive located on the transmission side with integral drive for the high-pressure fuel pump • Continuously variable intake and exhaust camshafts The use of FSI direct fuel injection technology makes it possible to meet current Low Emission Vehicle (LEV2) emission standards.OverviewTechnical data for the 3.2L V6 EngineConstruction Displacement Bore Stroke V Angle Valves per cylinder Compression ratio Max Output Max Torque Engine management Exhaust emission control Emission standard 6 cylinders narrow V engine 193.3 cu.in (3168 cm3) 3.4 in (86 mm) 3.58 in (90.9 mm) 10.6° 4 12:1 250 hp (184 kW) @ 6250 rpm 243 lbs.ft (330 Nm) @ 2750-3750 rpm Motronic MED 9.1 Three-way catalytic converters with O2 sensors LEV2Torque-power curve250 250225200200150175100150 50 1252000 4000 6000S360_116Power in hp Torque in lb.ftTechnical data for the 3.6L V6 FSI EngineConstruction Displacement Bore Stroke V Angle Valves per cylinder Compression ratio Max Output Max Torque Engine management Exhaust emission control Emission standard 6 cylinders narrow V engine 219.5 cu.in (3597 cm3) 3.5 in (89 mm) 3.8 in (96.4 mm) 10.6° 4 12:1 280 hp (206 kW) @ 6200 rpm 265 lbs.ft (360 Nm) @ 2500-5000 rpm Motronic MED 9.1 Three-way catalytic converters with O2 sensors LEV2Torque-power curve250 250225200200150175100150 50 1252000 4000 6000S360_115Power in hp Torque in lb.ftNotesEngine MechanicsThe Crank AssemblyThe Cylinder BlockS360_004The cylinder block has been significantly redesigned compared with the 3.2L manifold injection engine. The goal of the revision was to obtain a displacement of 3.6 liters without changing the exterior dimensions of the engine. This was achieved by changing the V-angle and the offset. Both FSI engines, the 3.2L and the 3.6L, have the new cylinder block. It is made of cast iron with lamellar graphite.Further innovations compared with the 3.2L manifold injection engine include: − Oil pump integral with the cylinder block − Better oil return from the cylinder block to the oil pan − Improved cylinder block rigidity, while reducing weight at the same time − Volumes of coolant in the cylinder block reduced by 0.7 liter, allowing the coolant to heat up faster.Engine MechanicsV angle 10.6° Cylinder Longitudinal AxisS360_003Crankshaft Center Axis Offset 22 mmThe V-angleThe V-angle of the cylinder block is 10.6°. By changing the V-angle from 15° to 10.6°, it was possible to provide the necessary cylinder wall thickness without changing the dimensions of the engine.OffsetBy reducing the V-angle, the cylinder longitudinal axis moves outward relative to the bottom of the crankshaft. The distance between the cylinder longitudinal axis and the crankshaft center axis is the Offset. The Offset is increased from 12.5 mm to 22 mm compared with the manifold injection engine.Engine MechanicsRunning-in CoatingPiston RecessS360_001The CrankshaftThe crankshaft is made of cast iron and is carried by 7 bearings, as in the 3.2L manifold injection engine.The Connecting RodsThe connecting rods are not cast but milled. The connecting rod eye is a trapezoidal design. The connecting rod bearings are molybdenum coated. This provides good break-in characteristics and high load capacityThe PistonsThe pistons are of the recessed piston design and are made of aluminum alloy. In order to improve break-in characteristics, they have a graphite coating. The pistons are different for the cylinder bank 1 and the cylinder bank 2. They differ in the arrangement of the valve pockets and the combustion chamber recess. The location and design of the piston recess generates a swirling motion of the injected fuel and mixes it with the intake air.Engine MechanicsThe Cylinder HeadInjectors 1, 3, 5S360_006Injectors 2, 4, 6S360_011High-Pressure Fuel Pump LocationS360_007The cylinder head is made of an aluminum-silicon-copper alloy and is identical for both engines. It is a new design as a result of the direct fuel injection. The cylinder head has been lengthened to accommodate the chain drive and to strengthen the high-pressure fuel pump mounting location. The fuel injectors for both cylinder banks are located on the intake side of the cylinder head.The fuel injectors bores for cylinders 1, 3 and 5 are located above the intake manifold flange. The fuel injectors for cylinders 2, 4 and 6 are installed below the intake manifold flange. As a result of this layout, the fuel injectors for cylinders 1, 3 and 5 pass through the cylinder head intake manifold. In order to compensate for the effect of the fuel injectors on the airflow characteristics in the intake manifold, the valve spacing for all cylinders has been increased from 34.5 mm to 36.5 mm. This reduces the change in airflow direction resulting from the fuel injectors when filling the cylindersNote Fuel injectors of two different lengths are required because of the two different positions for the fuel injectors.Engine MechanicsCamshaft AdjustmentIntake Camshaft AdjusterExhaust Camshaft AdjusterS360_012N318 Camshaft Adjustment Valve 1 (Exhaust) N205 Camshaft Adjustment Valve 1By adjusting the camshafts, power and torque can be increased, fuel consumption can be improved and emissions reduced, depending on the load characteristics of the engine. The camshafts are adjusted by two vane type adjusters. Both camshafts can be adjusted continuously in the direction of early valve opening and late valve opening. To adjust the camshafts, the Engine Control Module (ECM) actuates the solenoids: − N205 Camshaft Adjustment Valve 1 and − N318 Camshaft Adjustment Valve 1 (exhaust).Maximum adjustment of the camshafts: − Intake camshaft 52° from the crankshaft angle and − Exhaust camshaft 42° from the crankshaft angle. Both camshaft adjusters are adjusted by two valves with the assistance of the engine oil pressure. Adjusting both camshafts enables a maximum valve overlap of 42° crankshaft angle. The valve overlap allows for internal exhaust gas recirculation.Engine MechanicsInternal Exhaust Gas RecirculationInlet Manifold Vacuum Exhaust Valve Intake Valve Intake Valve opens Exhaust Valve closesValve OverlapCycle 4 Cycle 3 Cycle 2Cycle 1S360_124Internal exhaust gas recirculation counteracts the formation of nitrous oxides (NOx). Just as with external exhaust gas recirculation, the reduced formation of NOx is based on lowering combustion temperature by introducing combustion gases. The presence of combustion gases in the fresh fuel-air mixture produces a slight oxygen deficit. Combustion is not as hot as with an excess of oxygen. Nitrous oxides are not formed in greater concentrations until a relatively high temperature is reached. By reducing combustion temperature in the engine and with the lack of oxygen, the formation of NOx is reduced.OperationDuring the exhaust stroke, the intake and the exhaust valves are both open simultaneously. As a result of the high intake manifold vacuum, some of the combustion gases are drawn out of the combustion chamber back into the intake manifold and swirled into the combustion chamber with the next induction stroke for the next combustion cycle. Benefits of the internal exhaust gas recirculation: • Improved fuel consumption due to reduced gas exchange • Partial load range expanded with exhaust gas recirculation • Smoother idle • Exhaust gas recirculation possible even with a cold engine10Engine MechanicsCrankcase VentilationIt prevents hydrocarbon-enriched vapors (blow-by gases) from escaping from the crankcase into the atmosphere. Crankcase ventilation consists of vent passages in the cylinder block and cylinder head, the cyclone oil separator and the crankcase ventilation heater.OperationThe blow-by gases in the crankcase are drawn out by intake manifold vacuum through: − vent ports in the cylinder block, − vent ports in the cylinder head, − a cyclone oil separator and − a crankcase ventilation heater The blow-by gases are then rerouted into the intake manifold.Cyclone Oil Separator Crankcase Ventilation HeaterS360_064The Cyclone Oil SeparatorThe cyclone oil separator is located in the cylinder head cover. Its function is to separate oil from the blow-by gases from the crankcase and to return it to the primary oil circuit. A pressure regulator valve limits the intake manifold vacuum from about 700 mbar to about 40 mbar. It prevents the entire intake manifold vacuum and the internal crankcase vacuum from affecting the crankcase ventilation and drawing in engine oil or damaging seals.S360_253Ventilation Ports in the Cylinder Block and Cylinder HeadCyclone Oil SeparatorPressure Regulation ValveOil Ventto the Intake ManifoldS360_05811Engine MechanicsOperationThe cyclone oil separator separates the oil from the oil vapor drawn in. It works on the principle of centrifugal separation. Due to the cyclone design of the oil separator, the oil vapors drawn in are set into a rotating motion. The resulting centrifugal force throws the oil against the separating wall where it combines into larger drops. While the separated oil drips into the cylinder head, the gas particles are routed into the intake manifold through a flexible tube.Cyclone Oil Separator Vacuum Valve Intake Manifold Oil Vent OpeningS360_025InletGas Exit to the intake Manifold Gas ParticlesOil DropletsS360_059Oil Vent Opening into the CrankcaseCrankcase Ventilation HeatingThe heating element is installed in the flexible tube from the cyclone oil separator to the intake manifold, and prevents icing of the blow-by gases when the intake air is extremely cold.Heating ElementS360_026Note In the event of a defective pressure regulator valve, the full intake manifold vacuum and internal crankcase pressure are constantly applied to the crankcase ventilation. This causes a large amount of oil to be drawn out of the crankcase, possibly resulting in engine damage.12Engine MechanicsThe Intake ManifoldBoth engines have a single-piece overhead intake manifold made of plastic.Control Shaft with Flaps Short Resonance Pipe Power Manifold Long Resonance Pipe Main Manifold Crankcase VentilationS360_403Throttle Valve Control UnitDesignThe variable length intake manifold consists of: • the main manifold • two resonance pipes of different length per cylinder • the control shaft • the power manifold • the vacuum tank • the intake manifold valve The two resonance pipes differ in length because a long pipe is needed to achieve high torque and a short pipe is needed to achieve high power. The control shaft opens and closes the connection to the power manifold.13Engine MechanicsThe Control FlapsSwitching between the power and torque positions is accomplished by control flaps. The control flaps are vacuum operated by the Engine Control Module (ECM) J623 through the Intake Manifold Runner Control (IMRC) Valve N316. When current is not applied to the valve, the control flaps are open and are in the power setting.N316S360_022Control FlapsVacuum TankS360_405Check Valve Main ManifoldThe Vacuum TankA vacuum tank is located within the intake manifold. A vacuum supply is maintained in this vacuum tank and will allow to actuate the control flaps. The air from the vacuum tank is drawn through a check valve into the primary manifold, so that vacuum can build up in the vacuum tank. If the check valve is defective, the control flaps cannot be activated.J623N316S360_40414Engine MechanicsFunction of the Variable Length Intake ManifoldThe variable length intake manifold is designed so that a resonance is created between the timing of the valves, the intake pulses and the vibration of the air which produces an increase in pressure in the cylinder and subsequently good charging efficiency in the cylinder.Power Setting of the Variable Intake Manifold Power ManifoldTorque Setting of the Variable Intake ManifoldVariable Intake Manifold HousingAir Supply from the Power Manifold Control ShaftS360_063Air Supply from the Intake Manifold Control ShaftS360_062Engine Speed between 0 and about 1200 rpm The variable length intake manifold is in the power position. Current is not applied to the intake manifold flap control valve. The vacuum wave generated at the beginning of the intake stroke is reflected at the end of the power collector in the power manifold and returns after a brief time to the intake valve as a pressure wave.Engine Speed between about 1200 and 4000 rpm Current is applied from the ECM to the intake manifold flap control valve. The control flaps are closed and close the power manifold. The cylinders draw air through the torque manifold directly from the main manifold. Engine Speed above 4000 rpm No current is applied to the intake manifold flap control valve. As a result, the intake manifold claps switch back to the power position.15Engine MechanicsThe Chain DriveIntake Camshaft Drive Exhaust Camshaft DriveHigh-pressure Fuel Pump DriveHydraulic Chain TensionerOil Pump DriveHydraulic Chain Tensioner Crankshaft PinionS360_016The chain drive is located on the transmission side of the engine. It consists of the primary chain and the camshaft chain. The primary chain is driven by the crankshaft. It drives the camshaft chain and the oil pump via a sprocket wheel. Note Please refer to ElsaWeb when setting the valve timing. There is a new special tool T10332 for locking the high pressure-pump pinion wheel. The two camshafts and the high-pressure fuel pump are driven by the camshaft chain. Both chains are kept at the precise tension by hydraulic tensioners.16Engine MechanicsThe Ribbed V-belt DriveTensioning PulleyCoolant Pump DriveAlternator DriveIdler Pulley Crankshaft V-belt Drive PulleyAir-Conditioning Compressor DriveIdler PulleyS360_015Construction of the Poly-V Drive BeltCover Fabric Cover Layer Polyester Drive-ply Substructure Drive Belt PulleyS360_170The ribbed V-belt is a single-sided poly-V belt. Even at high speed, it runs quietly and vibration-free. The belt is driven by the crankshaft through the V-belt pulley with vibration damper.The belt drives the air-conditioning compressor, the alternator and the coolant pump. The V-belt is always kept at the correct tension by a belt tensioner.17Engine MechanicsOil CirculationCamshaft Adjuster Hydraulic Valve Lifter High-pressure Fuel Pump Drive Camshaft Bearing Camshaft AdjusterChain TensionerChain TensionerOil Tank Spray Jets for Piston LubricationOil PumpCrankshaft BearingOil TankIntake Duct Oil filter Cooler Module Oil ReturnOil PanS360_122Oil pressure is generated by a self-priming duocentric oil pump. It is installed in the cylinder block and is chain driven. The particular installation of the oil pump results in a longer path for the oil. With a longer path for the oil to travel, lubrication of engine components on startup can be an issue. For this reason, oil is drawn from an oil tank located behind the oil pump to ensure the initial supply of oil.The oil pump draws oil from the oil pan and then pumps it to the oil filter-cooler module. In that module, the oil is cleaned and cooled before it is transferred to the lubrication points in the engine.18Engine MechanicsThe Oil Pump with Oil TankThe oil tank is formed in the cylinder block by a cavity behind the oil pump. Its volume is approximately 280 ml and remains even after the engine is switched off.Cylinder HeadOil Tank Drive PinionService Opening Oil PumpCylinder BlockS360_174The Service Opening for the Oil Pump The service opening provides access to the oil pump excess-pressure piston with the engine installed. After removing the cover bolt and a second internal bolt, the oil pump pressure piston can be removed and its condition can be inspected without having to remove the drive chain.S360_052Cover ScrewPressure PistonS360_05619Engine MechanicsThe Oil Filter Cooler Module The oil filter cooler module is an assembly made of the oil filter, oil cooler, check valve and filter bypass valve.Oil CoolerS360_019The Oil Return The returning oil is directed through three return ducts in the cylinder head into a central oil return duct in the cylinder block. The oil then flows into the oil pan under the oil level. In addition to the central oil return, oil is returned to the oil pan from the front of the engine through the timing chain housing.Oil FilterS360_219Oil Return20Engine MechanicsCoolant CirculationLegend 1 2 3 4 5 6 7 8 9 10 11 Coolant Tank Heater Exchanger for Heating Coolant Pump Transmission Fluid Cooler Thermostat Oil Cooler Check Valve Recirculation Pump V55 Check Valve Auxiliary Cooler Radiator12345 6 789 1011S360_213The coolant is circulated by the mechanical coolant pump. The pump is driven by the V-belt. There are 9 liters (2.4 gallons) of coolant in the cooling system. The total amount of coolant has been reduced by 2 liters in comparison to the 3.2L injection engine. This allows the engine to more quickly reach its operating temperature. Coolant circulation is controlled by the expansion thermostat.Depending on the vehicle, there may be an auxiliary cooler in the coolant circuit. The check valves are included in the coolant circuit in order to prevent any coolant return flow.21Engine MechanicsThe Recirculation Pump V55The Recirculation Pump is an electrical pump. It is integrated into the engine coolant circuit and is actuated by the ECM based on a characteristic map. After the engine has been turned off, the Recirculation Pump is switched on depending on coolant temperature.The Coolant FanThe V6 FSI engine has two electric Coolant Fans. The Coolant Fans are activated as needed by the ECM. The Engine Control Module (ECM) J623 signals the need for radiator cooling to the Coolant Fan Control (FC) Module J293. Depending on the need, the Coolant Fan Control (FC) Module J293 then supplies current to one or both of the fans. Current is supplied to the Cooling Fan Control (FC) Module J293 by the Motronic Engine Control Module (ECM) Power Supply Relay J271 and by the Vehicle Electrical System Control Module J519. The fans can also be switched on by the Coolant Fan Control (FC) Module after the engine has been turned off. In order to turn on the fans when the engine has been turned off, the Coolant Fan Control (FC) Module has a connection to terminal 30.Engine Control Module (ECM) J623S360_169Coolant Fan V7Coolant Fan 2 V177 Motronic Engine Control Module (ECM) Power Supply Relay J271S360_171Terminal 30Vehicle Electrical System Control Module J519Coolant Fan Control (FC) Control Module J29322Engine MechanicsThe Exhaust System3.2-liter V6 FSI EngineG39 Primary Catalytic ConverterG130G108G131S360_117The exhaust system for the 3.2L engine has a primary catalytic converter for each cylinder bank with a ceramic base. Exhaust gas quality is monitored by two oxygen sensors upstream and downstream of the catalytic converters.3.6-liter V6 FSI engineG39 Pre-Catalytic Converter G130 Primary Catalytic ConverterG108G131S360_118The exhaust system for the 3.6L FSI engine is equipped with two pre-catalytic converters and 2 main catalytic converters. Exhaust gas quality is monitored by two oxygen sensors upstream of the pre-catalytic converters and two oxygen sensors downstream of the pre-catalytic converters. The exhaust system complies with Low Emission Vehicle (LEV2) emission standards.23Engine MechanicsFSI TechnologyContributing Factors- System Pressure - Start of Actuation - End of Actuation- Valve Timing - Intake Manifold Shape - Air Flow - Valve Lift - Valve Diameter - Fuel Flow - Spray Cone - Spray Angle- Recess Shape- Stroke - Bore - Engine rpmS360_407Direct gasoline injection requires precise timing of the combustion process. The factors affecting the combustion process are: • Cylinder bore and stroke • Shape of the recess in the piston surface • Valve diameter and lift • Valve timing • Geometry on the intake ports • Volumetric efficiency of the fresh air supplied • Fuel injector characteristics (spray cone, spray angle, flow amount, system pressure and timing) • Engine rpm An essential part in the optimization of the combustion performance is the study of airflow characteristics in the combustion chamber. The mixture formation is substantially affected by the flow characteristics of the intake air and the injected fuel.In order to determine the optimal airflow characteristics and as a result define the optimal piston shape for both banks of cylinders, Doppler Global Velocimetry was used. This procedure makes it possible to study airflow characteristics and mixture formation while the engine is running. With the help of this procedure and by modifying the characteristics of the fuel injectors it was possible to equalize and match airflow velocities and mixture formation in the combustion chambers for both cylinder banks.24Notes25Engine MechanicsThe Fuel SystemG6 Transfer Fuel Pump (FP)G247 Fuel Pressure Sensor G410 Low Fuel Pressure Sensor J538 Fuel Pump (FP) Control Module J623 Engine Control Module (ECM) N276 Fuel Pressure Regulator ValveLow-Pressure LinePressure Relief ValveFuel FilterPressure Retention ValveG6The Low-Pressure Fuel SystemThe low-pressure system transfers fuel from the fuel tank. The transfer fuel pump is activated by the ECM through the Fuel Pump Control Module depending on the requirements at a working pressure between 2 and 5 bars. The pressure retention valve maintains the fuel pressure when the engine is switched off. If the fuel line is ruptured in an accident, the pressure retention valve prevents fuel from escaping. The pressure relief valve opens at a pressure of 93 psi (6. 4 bar) and thus prevents excessive fuel pressure in the low-pressure line.OperationThe signal from the Low Fuel Pressure Sensor G410 informs constantly the ECM of the current fuel pressure. The ECM compares the current pressure to the required fuel pressure. If the current fuel pressure is not adequate to meet the fuel needs, the ECM activates the Fuel Pump (FP) Control Module J538. This control module then activates the transfer fuel pump, which increases the working pressure. When the fuel requirement drops again, the working pressure at the pump drops accordingly.26Engine MechanicsDistributor Rail Cylinder Bank 1G410 High-Pressure Fuel Pump High-Pressure LineFuel Injector Cylinder 1Fuel Injector Cylinder 3Fuel Injector Cylinder 5N276 Distributor Rail Cylinder Bank 2G247 J623 Fuel Injector Cylinder 2 Fuel Injector Cylinder 4 Fuel Injector Cylinder 6J538S360_321The High-Pressure Fuel SystemThe Fuel Pressure Sensor G247The Fuel Pressure Sensor G247 is installed in the fuel distributor of the cylinder bank 2 and informs the ECM of current pressure in the high-pressure fuel system.The pressure relief valveThe pressure relief valve is located on the fuel distributor of the cylinder bank 1. The valve opens a connection to the low-pressure fuel system when the fuel pressure in the high-pressure fuel system is over 1,740 psi (120 bars).The Fuel Pressure Regulator Valve N276The Fuel Pressure Regulator Valve N276 is threaded into the high-pressure fuel pump and regulates the pressure in the high-pressure fuel system according to the signal from the ECM.27Engine MechanicsThe High-Pressure Fuel PumpThe High-Pressure Fuel Pump is located on the cylinder head and is a piston pump. It is driven by the camshaft and generates a fuel pressure of 1,595 psi (110 bars).Low-Pressure Fuel LineHigh-Pressure Fuel LineLow Fuel Pressure Sensor G410Fuel Pressure Regulator Valve N276The High-Pressure Fuel Pump DriveThe High-Pressure Fuel Pump is driven by a pinion gear with dual cam. The dual cam actuates the pump piston through a roller. The pump piston generates the high pressure in the pump.S360_123High-Pressure Fuel PumpPump Piston Cylinder Head Cam Follower RollerDual CamS360_038Pinion GearS360_173Fuel Pump DriveDual CamPinion GearNote In order to install the camshaft roller chain, the High-Pressure Fuel Pump pinion must be locked with special tool T10332. Please refer to ElsaWeb for the latest repair information.28Engine MechanicsFuel Injector CharacteristicsExhaust Valve Intake ValveFuel Injector Piston RecessSince the fuel injectors are inserted from the same side for both banks of cylinders, the piston recess must be shaped differently. This is necessary because the fuel injectors and the intake valves for both cylinder banks are positioned at different angles. The shape and orientation of the fuel injection play an important role along with the quantity of fuel injected and the length of injection.Valve Angle Cylinder 1, 3, 5S360_252Valve PocketLate Pre-InjectionLate Ignition Timing Catalytic ConverterValve Angle Cylinder 2, 4, 6S360_251S360_159Hotter Combustion Gases heat up the Catalytic ConverterThe Homogenous Split Catalytic Converter Heating ProcessThe purpose of the Homogenous Split Catalytic Converter Heating Process is to bring quickly the catalytic converters to operating temperature after a cold start. To achieve this, the fuel is injected twice during one combustion cycle. The first injection takes place in the induction stroke. This achieves an even distribution of the fuel-air mixture. In the second injection, a small amount of fuel is additionally injected shortly before ignition Top Dead Center (TDC). The late injection increases exhaust gas temperature. The hot exhaust gas heats up the catalytic converter so that it reaches operating temperature more quickly.29Engine ManagementSystem OverviewSensorsEngine Speed (RPM) Sensor G28 Mass Air Flow (MAF) Sensor G70Throttle Position (TP) Sensor G79 Accelerator Pedal Position Sensor 2 G185Clutch Position Sensor G476 Throttle Valve Control Module J338 with Throttle Drive Angle Sensor 1 (for Electronic Power Control (EPC)) G187 Throttle Drive Angle Sensor 2 (for Electronic Power Control (EPC)) G188 Engine Control Module (ECM) J623 Camshaft Position (CMP) Sensor G40 Camshaft Position (CMP) Sensor 2 G163 Engine Coolant Temperature (ECT) Sensor G62 Engine Coolant Temperature (ECT) Sensor (on Radiator) G83 Knock Sensor (KS) 1 G61 Knock Sensor (KS) 2 G66Brake Light Switch FFuel Pressure Sensor G247 Low Fuel Pressure Sensor G410 CAN Data-bus Oil Level Thermal Sensor G266Heated Oxygen Sensor (HO2S) G39 Heated Oxygen Sensor (HO2S) 2 G108 Oxygen Sensor (O2S) Behind Three Way Catalytic Converter (TWC) G130 Oxygen Sensor (O2S) 2 Behind Three Way Catalytic Converter (TWC) G13130S360_154Engine ManagementActuatorsFuel Pump (FP) Control Module J538 Transfer Fuel Pump (FP) G6Cylinder 1-6 Fuel Injector N30, N31, N32, N33, N83, N84Ignition Coil 1-6 with Power Output Stage N70, N127, N291, N292, N323, N324Throttle Valve Control Module J338 with Throttle Drive (for Electronic Power Control (EPC)) G186Fuel Pressure Regulator Valve N276Evaporative Emission (EVAP) Canister Purge Regulator Valve N80Intake Manifold Runner Control (IMRC) Valve N316Camshaft Adjustment Valve 1 N205 Camshaft Adjustment Valve 1 (exhaust) N318Instrument Cluster Control Module J285Oxygen Sensor (O2S) Heater Z19 Oxygen Sensor (O2S) 2 Heater Z28 Oxygen Sensor (O2S) 1 (behind Three Way Catalytic Converter (TWC)) Heater Z29 Oxygen Sensor (O2S) 2 (behind Three Way Catalytic Converter (TWC)) Heater Z30 Third Speed Coolant Fan Control (FC) Relay (V35) J283 Coolant Fan V7 Coolant Fan 2 V177Recirculation Pump Relay J160 Recirculation Pump V55S360_155 31Engine ManagementSensorsEngine Speed (RPM) Sensor G28The Engine Speed Sensor is threaded into the side of the cylinder block. It scans the sensor wheel on the crankshaft.Signal UtilizationThe engine speed and the exact position of the crankshaft relative to the camshaft are determined by the engine speed sensor. Using this information, the injection quantity and the start of injection are calculated.Effects of Signal FailureIn case of signal failure, the engine is switched off and cannot be restarted.S360_11132Engine ManagementMass Airflow Sensor G70The 6th generation hot film mass airflow sensor (HFM6) is used in the 3.2L and the 3.6L FSI engine. It is located in the intake manifold and operates based on a thermal measurement principle, as did its predecessor.Characteristics• Micromechanical sensor element with reverse current detection • Signal processing with temperature compensation • High measurement accuracy • High sensor stabilityConnectorSensor ElectronicsDrawn-in AirS360_183Bypass Channel33Engine ManagementOperationThe sensor element for the Mass Airflow Sensor protrudes into the airstream of the air drawn in by the engine. Some of the air flows through the bypass duct of the mass air flow sensor. The electronic sensor system is located in the bypass duct. A heating resistor and two temperature sensors are located in the electronic sensor system. The two temperature sensors detect the direction of airflow: • The intake air passes first over temperature sensor 1 • The air returning from the closed valves passes first over temperature sensor 2 Using the heating resistor, the ECM can draw conclusions about the oxygen content of the intake air.Sensor ElementS360_178Measurement of the Intake Air Cut-out Mass Airflow SensorSignal UtilizationThe signal from the mass airflow sensor is used in the ECM to calculate the volumetric efficiency. Based on the volumetric efficiency, and taking into consideration the lambda value and ignition timing, the control module calculates the engine torque.Heating Resistor Temperature SensorS360_179Intake Air FlowEffects of Signal FailureIf the mass airflow sensor fails, the engine management system calculates a substitute value.Measurement of the air returning from the closed valveS360_180Returning Air FlowTemperature Sensor 2 Heating ResistorS360_181 34Engine ManagementThe Throttle Position (TP) Sensor G79 and the Accelerator Pedal Position Sensor 2 G185The two throttle position sensors are part of the accelerator pedal module and are contact-free sensors. The ECM detects the driver’s request from these sensor signals.G79 and G185Signal UtilizationThe ECM uses the signals from the Throttle Position Sensor to calculate the fuel injection volume.Accelerator PedalEffects of a Signal FailureIf one or both sensors fails, a DTC is set and memory and the EPC light is switched on. Comfort functions such as cruise control or engine drag torque control are switched off.Clutch Position Sensor G476The Clutch Position Sensor is a mechanically actuated switch located on the clutch pedal. It is only required on vehicles with manual transmission.S360_150Signal UtilizationThe signal is used to control the cruise control and to control the ignition timing and quantity of fuel when shifting.Effects of a Signal FailureThe cruise control cannot be turned on. It also results in driveability problems, such as engine jerking and increased RPM when shifting.Sensor Cylinder Clutch Pedal ModuleG476S360_16335Engine ManagementThe Throttle Drive Angle Sensor 1 G187 and Throttle Drive Angle Sensor 2 G188 in the Throttle Valve Control UnitThese sensors determine the current position of the throttle valve and send this information to the ECM.Throttle Valve Housing Throttle Valve DriveSignal UtilizationThe ECM recognizes the position of the throttle valve from the angle sensors signals. The signals from the two sensors are redundant, meaning that both sensors provide the same signal for reasons of safety.Effects of a Signal FailureExample 1 The ECM receives an implausible signal or no signal at all from an angle sensor:Throttle Valve• A DTC is set and the EPC light is switched on • Systems which affect torque, (e.g. cruise control system or engine drag torque control), are switched off • The load signal is used to monitor the remaining angle sensor • The accelerator pedal responds normally Example 2G187 and G188S360_238The ECM receives an implausible signal or no signal from both angle sensors: • DTCs are set for both sensors and the EPC light is switched on • The throttle valve drive is switched off • The engine runs only at an increased idle speed of 1,500 RPM and no longer reacts to the accelerator pedal36Engine ManagementThe Camshaft Position Sensors (CMP) G40 and G163Both Hall sensors are located in the engine timing chain cover. Their task is to communicate the position of the intake and exhaust camshafts to the ECM. To do this, they scan a quick-start sensor wheel which is located on the individual camshaft. The ECM recognizes the position of the intake camshaft from the Camshaft Position (CMP) Sensor G40, and recognizes the position of the exhaust camshaft from Camshaft Position (CMP) Sensor 2 G163.G40G163S360_108Signal UtilizationUsing the signal from the Camshaft Position Sensors, the precise position of the camshaft relative to the crankshaft is determined very quickly when the engine is started. Used in combination with the signal from the Engine Speed (RPM) Sensor G28, the signals from the Camshaft Position Sensors allow to detect which cylinder is at TDC. The fuel can be injected into the corresponding cylinder and ignited.Effects of a Signal FailureIn case of signal failure, the signal from the Engine Speed (RPM) Sensor G28 is used instead. Because the camshaft position and the cylinder position cannot be recognized as quickly, it may take longer to start the engine.37Engine ManagementThe Engine Coolant Temperature (ECT) Sensor G62This sensor is located at the coolant distributor above the oil filter on the engine and it informs the ECM of the coolant temperature.Signal UtilizationThe coolant temperature is used by the ECM for different engine functions. For example, the computation for the injection amount, compressor pressure, start of fuel delivery and the amount of exhaust gas recirculation.Effects of a Signal FailureIf the signal fails, the ECM uses the signal from the Engine Coolant Temperature (ECT) Sensor G83.G62S360_164The Engine Coolant Temperature (ECT) Sensor (on the Radiator) G83The Engine Coolant Temperature Sensor (on the Radiator) G83 is located in the radiator output line and measures the coolant exit temperature.Radiator InletSignal UtilizationThe radiator fan is activated by comparing both signal from the Engine Coolant Temperature Sensors G62 and G83.Effects of a Signal FailureIf the signal from the Engine Coolant Temperature Sensor G83 is lost, the first speed engine coolant fan is activated permanently.Radiator OutletG83S360_18238Engine ManagementKnock Sensors (KS) 1 G61 and Knock Sensors (KS) 2 G66The Knock Sensors are threaded into the crankcase. They detect combustion knocks in individual cylinders. To prevent combustion knock, a cylinder-selective knock control overrides the electronic control of the ignition timing.S360_158G61S360_157G66Signal UtilizationBased on the knock sensor signals, the ECM initiates ignition timing adjustment in the knocking cylinder until knocking stops.Effects of a Signal FailureIn the event of a knock sensor failure, the ignition timing for the affected cylinder group is retarded. This means that a safety timing angle is set in the “late“ direction. This can lead to an increase in fuel consumption. Knock control for the cylinder group of the remaining knock sensor remains in effect. If both knock sensors fail, the engine management system goes into emergency knock control in which the ignition angle is retarded across the board so that full engine power is no longer available.39Engine ManagementThe Brake Light Switch FThe Brake Light Switch is located on the tandem master cylinder. It scans a magnetic ring on the tandem master cylinder piston using a contactless Hall Element. This switch provides the Engine Control Module with the signal “Brake actuated“ via the CAN data bus drive.Signal UtilizationWhen the brake is operated, the cruise control system is deactivated. If the signal “accelerator pedal actuated“ is detected first and “brake actuated“ is detected next, the idle speed is increased.Effects of a Signal FailureIf the sensor signal is lost, the amount of fuel injected is reduced and the engine has less power. The cruise control system is also deactivated.S360_177The Fuel Pressure Sensor G247The Fuel Pressure Sensor is located on the lower fuel distributor pipe. It measures the fuel pressure in the high-pressure fuel system.Signal UtilizationThe ECM analyzes the signal and regulates the fuel high pressure through the Fuel Pressure Regulator Valve N276 in the high-pressure pump.Effects of a Signal FailureIf the Fuel Pressure Sensor fails, the fuel pressure regulator valve is activated at a fixed value by the ECM.S360_110G24740Engine ManagementThe Low Fuel Pressure Sensor G410The Low Fuel Pressure Sensor is located on the highpressure fuel pump. It measures the fuel pressure in the low-pressure fuel system.Signal UtilizationThe signal is used by the ECM to regulate the lowpressure fuel system. Based on the signal from the sensor, a signal is sent by the ECM to the Fuel Pump Control Module J538, which then regulates the fuel pump as needed.Effects of a Signal FailureIf the Low Fuel Pressure Sensor fails, the fuel pressure is not regulated as needed. Fuel pressure is maintained at a constant 72 psi (5 bar).G410S360_109The Oil Level Thermal Sensor G266The Oil Level Thermal Sensor is threaded into the oil pan from below. Its signal is used by several control modules.Signal UtilizationThe ECM receives the signal over the CAN data bus and uses the oil temperature signal to control the retarded setting of the exhaust camshaft at high oil temperatures.Effects of a Signal FailureThe control module uses instead the signal from the Coolant Temperature Sensor.S360_15641Engine ManagementThe Heated Oxygen Sensors (HO2S) G39 and the Heated Oxygen Sensors (HO2S) 2 G108A broadband oxygen sensor is assigned to each precatalytic converter as a pre-catalytic oxygen sensor. Using the broadband oxygen sensors, a wide range of oxygen concentration in the exhaust gas can be determined, allowing to derive information about the air-fuel ratio in the combustion chamber. Both oxygen sensors are heated to reach operating temperature more quickly.Broadband Oxygen SensorSignal UtilizationThe signals from the Heated Oxygen Sensors are one of the variables used in calculating the injection timing.S360_222Effects of a Signal FailureIf the pre-catalytic converter oxygen sensor fails, there is no closed loop control. The fuel injection adaptation is not available. An emergency running mode is enabled using an engine characteristics map.The Oxygen Sensor (O2S) Behind Three Way Catalytic Converter G130 and the Oxygen Sensor (O2S) 2 Behind Three Way Catalytic Converter G131The planar oxygen sensors are located downstream of the pre-catalytic converter. They measure the remaining oxygen content in the exhaust gas. Based on the amount of oxygen remaining in the exhaust gas, the ECM can draw conclusions about the catalytic converter operation.Planar Oxygen SensorSignal UtilizationThe ECM uses the signals from the post-catalytic converter oxygen sensors to check the catalytic converter operation and the closed-loop oxygen control system.S360_224Effects of a Signal FailureIf the post-catalytic converter oxygen sensor fails, the closed loop operation continues. The operation of the catalytic converter can no longer be checked.42Engine ManagementThe ActuatorsCamshaft Adjustment Valve 1 N205, Camshaft Adjustment Valve 1 (exhaust) N318The solenoid valves are integrated in the camshaft adjustment housing. They distribute the oil pressure based on the ECM signals for the adjustment direction and adjustment travel at the camshaft adjusters. Both camshafts are continuously adjustable: • Intake camshaft at 52° of the crankshaft angle • Exhaust camshaft at 42° of the crankshaft angle • Maximum valve overlap angle 47° The exhaust camshaft is mechanically locked when no oil pressure is available (engine not running).N205N318S360_161Effects of a Signal FailureIf an electrical lead to the camshaft adjusters is defective or if a camshaft adjuster fails because it is mechanically seized or as a result of inadequate oil pressure, there is no camshaft adjustment.43Engine ManagementThe Transfer Fuel Pump (FP) G6 and the Fuel Level Sensor GThe Transfer Fuel Pump and the Fuel Filter are combined in the Fuel Transfer Unit. The Fuel Transfer Unit is located in the fuel tank.OperationThe Transfer Fuel Pump transfers the fuel in the lowpressure fuel system to the high-pressure fuel pump. It is activated by a Pulse Width Modulation (PWM) signal from the Fuel Pump Control Module. The Transfer Fuel Pump transfers as much fuel as the engine requires at any point in time.S360_190Effects of a FailureIf the Transfer Fuel Pump fails, engine operation is not possible.The Fuel Pressure Regulator Valve N276The Fuel Pressure Regulator Valve is located on the underside of the High-Pressure Fuel Pump. The ECM regulates the fuel high-pressure through the Fuel Pressure Regulator Valve at a level between 507 and 1,450 psi (35 and 100 bar).Effects of a FailureThe ECM goes into emergency running mode.High-Pressure Fuel PumpS360_162N27644Engine ManagementThe Ignition Coils 1-6 with Power Output Stage N70, N127, N291, N292, N323, N324The ignition coil and power output stage are one component. The ignition timing is controlled individually for each cylinder.Effects of a FailureIf an ignition coil fails, fuel injection for the affected cylinder is switched off. This is possible for a maximum of two cylinders.S360_192Ignition CoilsThe Evaporative Emission (EVAP) Canister Purge Regulator Valve N80The Evaporative Emission Canister Purge Regulator Valve is located on the front (belt drive side) of the engine and is triggered by the ECM. The fuel vapors collected in the evaporative emission canister are sent for combustion and thus the evaporative emission canister is emptied.Effects of a Signal FailureIf the current is interrupted, the valve remains closed. The fuel tank is not vented.N80S360_40645Engine ManagementThe Cylinders 1-6 Fuel Injectors N30, N31, N32, N33, N83, N84The High-Pressure FSI Fuel Injectors are inserted into the cylinder head. They are triggered by the ECM in accordance with the firing orders. When triggered, they spray fuel directly into the cylinder. Due to the design of the engine, injection takes place from one side. For this reason, the fuel injectors for cylinder bank 1, 3 and 5 are longer than the fuel injectors for cylinder bank 2, 4 and 6.Effects of a FailureA defective fuel injector is recognized by misfire detection and is no longer triggered.S360_137Throttle Drive for Electronic Power Control (EPC) G186The Throttle Drive for Electronic Power Control is an electrical motor which operates the throttle valve through a gear mechanism. The range of adjustment is stepless from idle to the wide-open throttle position.Throttle Valve Housing G186Effects of a FailureIf the throttle drive fails, the throttle valve is automatically pulled to the emergency running position. An entry is made in the DTC memory and the EPC lamp is switched on. The driver has only emergency features available. The comfort functions are switched off.Throttle ValveS360_19546Engine ManagementIntake Manifold Runner Control Valve N316The Intake Manifold Runner Control Valve is located on the variable intake manifold and is an electropneumatic valve. When it is activated, it operates the intake manifold flap to change the length of the intake manifold.Effects of a FailureIf the valve fails, the intake manifold flaps are pulled by a mechanical spring to an emergency running position. This position corresponds to the power setting of the intake manifold.The Recirculation Pump V55The Recirculation Pump is activated by the ECM. It assists the mechanical coolant pump when the engine is running. After the engine is turned off and with a lack of moving air resulting from the vehicle motion, the Recirculation Pump is switched on depending on the coolant temperature, and prevents a heat buildup in the engine.N316S360_051Effects of a FailureIf the Recirculation Pump fails, the engine may overheat.V55S360_04547Engine ManagementOxygen Sensor (O2S) Heaters Z19, Z28, Z29 and Z30The job of the Oxygen Sensor Heater is to bring the ceramic of the oxygen sensor rapidly up to its operating temperature of approx. 1652°F (900°C) when the engine is started and the temperature is low. The oxygen sensor heater is controlled by the ECM.Effects of a FailureThe engine can no longer be regulated with respect to the emissions.Oxygen Sensor HeaterS360_19348Engine ManagementThe Control Modules in the CAN Data BusThe schematic below shows the Engine Control Module J623 integrated into the CAN data bus structure of the vehicle. Information is exchanged between the control modules over the CAN data bus.J743 J217 J104 J623J533 J285 J519 J234S360_175J257Legend J623 Engine Control Module (ECM) J104 ABS Control Module J217 Transmission Control Module (TCM) J234 Airbag Control Module J285 Instrument Cluster Control Module J519 Vehicle Electrical System Control Module J527 Steering Column Electronic Systems Control Module J533 Data Bus On Board Diagnostic Interface J743 Direct Shift Gearbox (DSG) MechatronicColor coding Powertrain CAN-bus Comfort system CAN-bus Infotainment CAN-bus49Operating DiagramsJ519K30 K15G39G130J160J271J670Z19Z29J623N70N127N291N292N323N324J257 N30 N31S360_165G39 Heated Oxygen Sensor (HO2S)N127 Ignition Coil 2 with Power Output Stage N291 Ignition Coil 3 with Power Output Stage N292 Ignition Coil 4 with Power Output Stage N323 Ignition Coil 5 with Power Output Stage N324 Ignition Coil 6 with Power Output Stage Z19 Z29 Oxygen Sensor (O2S) Heater Oxygen Sensor (O2S) 1 (behind Three Way Catalytic Converter (TWC)) HeaterG130 Oxygen Sensor (O2S) Behind Three Way Catalytic Converter (TWC) J160 Recirculation Pump Relay J271 Motronic Engine Control Module (ECM) Power Supply Relay J519 Vehicle Electrical System Control Module J623 Engine Control Module (ECM) J670 Motronic Engine Control Module (ECM) Power Supply Relay 2 N30 N31 N70 Cylinder 1 Fuel Injector Cylinder 2 Fuel Injector Ignition Coil 1 with Power Output Stage50Operating DiagramsJ519GG6F1G266 CANJ285 J538 F N276G1G5G21J623G28G61G66G79G185 G186 G187 G188J338S360_166F F1 G G1 G5 G6 G21 G28 G61 G66 G79 Brake Light Switch Oil Pressure Switch Fuel Level Sensor Fuel Gauge Tachometer Transfer Fuel Pump (FP) Speedometer Engine Speed (RPM) Sensor Knock Sensor (KS) 1 Knock Sensor (KS) 2 Throttle Position (TP) SensorG187 Throttle Drive Angle Sensor 1 (for Electronic Power Control (EPC)) G188 Throttle Drive Angle Sensor 2 (for Electronic Power Control (EPC)) G266 Oil Level Thermal Sensor J285 Instrument Cluster Control Module J338 Throttle Valve Control Module J538 Fuel Pump (FP) Control Module J623 Engine Control Module (ECM) N276 Fuel Pressure Regulator ValveG185 Accelerator Pedal Position Sensor 2 G186 Throttle Drive (for Electronic Power Control (EPC))51Operating DiagramsJ519G108G131Z28Z30N205N80N316N318V7J293V177J623G410 N32 N33 N83 N84G163G83G40G247S360_167G40 G83 Camshaft Position (CMP) Sensor Engine Coolant Temperature (ECT) Sensor (on Radiator)N33 N80 N83 N84 Cylinder 4 Fuel Injector Evaporative Emission (EVAP) Canister Purge Regulator Valve Cylinder 5 Fuel Injector Cylinder 6 Fuel InjectorG108 Heated Oxygen Sensor (HO2S) 2 G131 Oxygen Sensor (O2S) 2 Behind Three Way Catalytic Converter (TWC) G163 Camshaft Position (CMP) Sensor 2 G247 Fuel Pressure Sensor G410 Low Fuel Pressure Sensor J293 Coolant Fan Control (FC) Control Module J519 Vehicle Electrical System Control Module J623 Engine Control Module (ECM) N32 Cylinder 3 Fuel InjectorN205 Camshaft Adjustment Valve 1 N316 Intake Manifold Runner Control (IMRC) Valve N318 Camshaft Adjustment Valve 1 (exhaust) V7 Coolant Fan V177 Coolant Fan 252Operating DiagramsJ519 J533 K30 K15Input signal Output signal Plus Ground CAN DatabusCANG42G70INOUTJ623G62J527S360_168G62 G42 G70 Engine Coolant Temperature (ECT) Sensor Intake Air Temperature (IAT) Sensor Mass Air Flow (MAF) SensorZ28 Z30 Oxygen Sensor (O2S) 2 Heater Oxygen Sensor (O2S) 2 (behind Three Way Catalytic Converter (TWC)) HeaterJ519 Vehicle Electrical System Control Module J527 Steering Column Electronic Systems Control Module J533 Data Bus On Board Diagnostic Interface J623 Engine Control Module (ECM)53Notes54ServiceSpecial ToolsDescriptionFunnel T 10333ToolUseThe Funnel T 10333 is used for installing the pistons on the 3.6 V6 FSI engine.Puller T10055 Adapter T 10055/3The Puller T10055 with Adapter T 10055/3 is used to remove the oil pump.Tool Set T 10133 Puller T 10133/10The Tool Set T 10133 with Puller T 10133/10 is needed to remove the fuel injectors.Adjusting tool T 10332The Adjusting Tool T 10332 must be used to lock the pinion on the high-pressure fuel pump drive.55Notes56Knowledge AssessmentAn on-line Knowledge Assessment (exam) is available for this Self-Study Program. The Knowledge Assessment may or may not be required for Certification. You can find this Knowledge Assessment at: www.accessaudi.comFor assistance, please call: Audi Academy Learning Management Center Headquarters 1-877-AUDI-LMC (283-4562) (8:00 a.m. to 8:00 p.m. EST)57All rights reserved. Technical specifications subject to change without noticeAudi of America, Inc. 3800 Hamlin Road Auburn Hills, MI 48326