TECHNICAL DOCUMENTATION

SSP 941003 Audi Engine Management

PDFEN184 pages14 MB
SSP 941003 Audi Engine Management - PDF cover

This PDF is currently unavailable.

Read document text
Engine Management SystemsDesign and FunctionSelf-Study Program Course Number 941003 Audi of America, Inc. Service Training Printed in U.S.A. Printed 5/2000 Course Number 941003 All rights reserved. All information contained in this manual is based on the latest product information available at the time of printing. The right is reserved to make changes at any time without notice. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, without the prior permission of the publisher. This includes text, figures and tables. Always check Technical Bulletins and the Audi Worldwide Repair Information System for information that may supersede any information included in this booklet. Table of ContentsPage Introduction ..............................................................................................1 Course goals ...............................................................................................2 Principles of engine operation ....................................................................3 Basic four-stroke principle .......................................................................... 3 Gasoline properties ....................................................................................6 Air/fuel mixture formation ...........................................................................8 Fuel system, overview .............................................................................10 Evolution of Engine Management Systems .............................................11 Ignition system, overview ........................................................................12 Emissions system, overview ....................................................................18 Three-way Catalytic Converter, overview .................................................20 On Board Diagnostics ..............................................................................22 Review ......................................................................................................25 Continuous Injection System ................................................................27 CIS ............................................................................................................28 K-Jetronic with Lambda control ................................................................30 CIS-E .........................................................................................................32 CIS-E III .....................................................................................................35 CIS Turbo ..................................................................................................38 CIS-E Motronic .........................................................................................39 Motronic M2.3.2 Overview ....................................................................43 System description ...................................................................................43 Inputs/Outputs - 20 Valve Turbo Motronic M2.3.2 ..................................47 Inputs/Outputs - 4.2 Liter V8 Motronic M2.3.2 .......................................51 On Board Diagnostics ...............................................................................54 Motronic M2.3.2 Component Summary ...............................................55 Input sensors ............................................................................................57 Actuators (outputs) ..................................................................................72 Review ......................................................................................................83 MPI - Multi Port Fuel Injection system .................................................85 System description ...................................................................................85 MMS 100/200 overview ...........................................................................86 On Board Diagnostic (OBD) ......................................................................86 MMS 100/200 System Components ........................................................87 MMS 300/311 overview, system description and comparison ..............104 OBD-II Overview ..................................................................................107 Background .............................................................................................107 OBD-II .....................................................................................................108 Diagnostic Trouble Codes ......................................................................110 Readiness Codes ....................................................................................111 Summary ................................................................................................112E Table of ContentsPage MMS 400/410/411 Overview ...............................................................113 Oxygen Sensor(s) (O2S) behind Three Way Catalyst (TWC) G130/G131 .................................................. 114 Sensor for EVAP canister G172 ..............................................................115 Data Link Connector (DLC) .....................................................................115 Secondary Air Injection (AIR) ..................................................................116 Leak Detection Pump (LDP) V144 ..........................................................117 Motronic M5.4.2 Overview ..................................................................119 System Description ................................................................................119 Input/Outputs - Motronic M5.4.2 ..........................................................120 Additional Systems .................................................................................121 A8 Motronic M5.4.2 system overview ..................................................122 Motronic M5.4.2 Components ...............................................................125 Input Sensors .........................................................................................126 Actuators (outputs) .................................................................................131 Motronic M5.9.2 Overview .................................................................. 139 System Description ................................................................................139 Input/Outputs - Motronic M5.9.2 ..........................................................140 Additional Systems .................................................................................141 1.8 liter turbo, system overview ............................................................142 Motronic M5.9.2 Component Differences ..........................................143 Engine Control Module J220 ..................................................................143 Combined Sensors/Actuators .................................................................144 Input Sensors .........................................................................................147 Actuators (outputs) .................................................................................152 Review ...................................................................................................156 Motronic ME 7 ......................................................................................159 Pathways ................................................................................................159 Components of Motronic ME 7.............................................................. 159 Electronic throttle control .......................................................................164 Review ...................................................................................................169 Level one course preparation ..............................................................171 Critical Thinking Skills .............................................................................171 Audi Electronic Service Information Service (AESIS) navigation ............172 Audi HELP line/Tech-tip line ...................................................................172 Diagnostic and Special Tools ..................................................................173 Review questions ...................................................................................173 Suggested reading and reference .......................................................173 Glossary ................................................................................................175 Post-test ................................................................................................179E IntroductionIntroductionThe origins of Audi engine development can be traced back to a 1913 4-cylinder liquidcooled engine designed by August Horch (1868-1951) in Zwickau, Germany. This greatgrandfather of the modern Audi engine shared the same operating principles as the most modern 5-valve per cylinder watercooled automotive engine. Both engines are four-stroke reciprocating internal combustion engines, and although a direct comparison cannot be made, the basic operating principles remain the same. Technology moved the four-stroke engine from magnetos and carburetors to ignition coils, points, distributors, mechanical fuel injection, hydraulic fuel injection, electronic ignition, electronic fuel injection, and finally to the combined fuel and ignition control of modern Motronic engine management systems. Motronic engine management systems use electronics to precisely monitor and control every aspect of engine operation, thereby improving efficiency, power, and driveability, while at the same time reducing fuel consumption and tailpipe emissions.1 IntroductionMotronic engine management systems control engine operation so precisely that it is no longer possible to identify a separate emissions system. All functions previously identified as emissions system functions are now components of Motronic engine management. The intent of this program is to provide information that will yield a greater understanding of engine management systems commonly in use, and the progression leading to the newest Motronic ME 7 system. Course goals • review principles of engine operation • explain the progression of engine management systems used by Audi • provide an in-depth understanding of both previous engine management systems and the state-of-the-art engine management systems in use today2 Principles of engine operationPrinciples of engine operationBasic four-stroke principle An internal combustion engine requires the proper ratios of air and fuel, combined with a properly timed spark for efficient combustion. Operation of most automotive engines is described in two upward and two downward movements of the piston, called strokes. These four strokes occur during two revolutions of the crankshaft and one revolution of the camshaft. The complete process of cyclic external spark ignition resulting in internal combustion is called the “Otto cycle.” All four-stroke engines operate in the same manner, regardless of the number of cylinders, although an engine with multiple cylinders has more firing pulses, resulting in a smoother running engine. Intake stroke (1) The first phase of engine operation begins with the intake valve opening and the piston moving down into the cylinder. This draws air and atomized fuel into the cylinder. Compression stroke (2) Operation continues with the piston at the bottom of its stroke, and the intake valve closing. The piston moves up in the cylinder, compressing the air/fuel mixture. Near the end of the stroke the air/fuel mixture is ignited by the ignition system. Combustion (power) stroke (3) As the air/fuel mixture burns it expands, creating pressure within the cylinder, pushing the piston down. This provides the motion which turns the crankshaft. Exhaust stroke (4) The exhaust valve opens near the end of the power stroke and the piston moves up. The burned gases are pushed up and out the exhaust port, and the cycle is repeated.3 Principles of engine operationMechanical systems Several support systems are required to make the combustion process occur continuously. The valvetrain operates the valves, the lubrication system supplies the oil, the cooling system removes heat, and the electrical system supplies the voltage. The engine management system delivers fuel and spark to match the air demands of the engine. Because of heat and drag, the thermal efficiency of a typical gasoline engine is around 25% (approximately one fourth of the heat energy of the fuel is converted into usable engine power). Mechanical Integrity The mechanical condition of the cylinder directly influences the combustion process. Conditions within the combustion chamber can also be influenced by other factors, including: • Camshaft timing • Oil pressure • Restrictions in the intake or exhaust paths The following diagnostic tests are used to check cylinder condition: • Compression test: This test can be useful in evaluating condition of the piston rings, head gasket and valve sealing ability when used in conjunction with other diagnostic tests. A compression test requires the removal of all the spark plugs. A pressure gauge is then threaded into the spark plug hole. The engine is cranked for a specified number of pulses using the starter, while applying Wide Open Throttle (WOT). Pressure gauge readings are then compared to factory specifications. To ensure the accuracy of the test, the engine should be at normal operating temperature.4 Principles of engine operation• Cylinder leakdown test A cylinder leakdown test is especially useful to identify sources of cylinder leakage. As an example, a hissing sound heard at the tailpipe while the test is being performed indicates possible leaking exhaust valves. A cylinder leakdown test also requires the removal of the spark plugs, but necessitates that the crankshaft be turned so that the piston is at the top of the compression stroke (Top Dead Center or TDC) with both valves closed. A measured amount of compressed air is applied to the cylinder through the spark plug hole using a leakdown tester. The pressure of the air in the cylinder is compared to the pressure being applied. A “percentage of leakage reading” is given by the gauge. The reading is compared to adjacent cylinders to determine cylinder condition. As in the compression test, the engine should be at normal operating temperature to ensure the accuracy of the test. Summary For any combustion process to occur, proper air/fuel mixture and a source of ignition are required. For an internal combustion engine to operate, the air/fuel mixture must be compressed, and the spark must occur at the proper time to create the combustion that is the motive force used to drive the piston. The mechanical systems must all work together to draw the combustible mixture into the cylinder, to compress it, to extract maximum power from combustion and to expel what remains after the combustion process. These systems work together to provide the support necessary to keep the engine running.5 Principles of engine operationGasoline properties For the engine management system to allow the engine to operate at peak efficiency and power, the octane rating of the gasoline must be within factory specifications as outlined in the owners manual. Octane is a relative measure showing the gasoline’s ability to resist self-ignition due to heat and pressure within the cylinder. Self ignition of the fuel is known as knocking (detonation) or pinging (pre-ignition). • Pinging: When the air/fuel mixture ignites before the spark occurs. • Knock: When a pressure wave from spark igniting the fuel creates a secondary combustion, causing the two pressure waves to collide. Gasoline with higher octane numbers resist temperature and pressure better, and therefore have less tendency to self-ignite. Several methods of measuring octane are used worldwide. These include the following: • Research Octane Number (RON); tests resistance to knock at lower engine speeds. • Motor Octane Number (MON); tests resistance to knock at higher engine speeds. In an effort to simplify a confusing array of octane numbers, the United States Government enacted legislation requiring the posting of a number on the dispensing pump reflecting the minimum octane number as determined by the Cost of Living Council (CLC). The CLC number is derived from both the RON and the MON as follows:The CLC number was later changed to the Anti-Knock Index (AKI) number. Gasolines identified as “regular” generally have an AKI number of around 87, while gasolines identified as “premium” generally have an AKI number around 92. AKI numbers apply to gasoline that is freshly pumped. Gasoline that is exposed to the air for extended periods of time undergoes a decrease in AKI number due to evaporation and oxidation.6 Principles of engine operationModern pump gasoline contains a wide variety of additives to help obtain optimal engine and fuel system operation. The additive package added to the base gasoline will include at least the following: • Anti-aging additives • Intake contamination inhibitors (detergents) • Corrosion inhibitors • Icing protection • Anti-knock additives Different concentrations of additives, along with other blending considerations, are used according to market and seasonal demands. All Audi Owner’s Manuals list recommended fuel grade specifications, along with notes on the use of fuels containing methanol, ethanol and MTBE (methyl tertiary butyl ether). • Octane must be between 87 AKI and 93 AKI, but exact requirements depend on model and year. • MTBE is blended with gasoline and sold in some areas of the country as oxygenated fuel to help reduce tailpipe emissions. This fuel can be used as long as specific percentage requirements are maintained and octane minimums are met. • Methanol and ethanol are types of alcohol commonly mixed with gasoline. Fuel with these additives can be used as long as specific percentage requirements are maintained and octane minimums are met. These requirements vary from year to year. The combustion process is dependent on the correct grade and quality of gasoline. If gasoline sits for an extended period of time, the octane can evaporate from the fuel, creating a varnished residue. This can restrict injector flow and fuel pump/fuel line performance. This can lead to hard starting, reduced performance and no code driveability complaints. Note: MTBE has been identified by the Government as a possible carcinogen and is being phased out in automotive use.7 Principles of engine operationAir/fuel mixture formation The function of the fuel system is to deliver the correct air/fuel mixture to the engine. The optimal air/fuel ratio for complete combustion is 14.7 parts air to 1 part fuel by volume. This is referred to as the stoichiometric ratio . Mixture corrections must be made as required to satisfy the differing engine demands encountered under any given driving condition. Engine operating conditions include: • Idle: For a smooth and efficient idle, the air/fuel mixture must be 14.7:1 (stoichiometric ratio). • Part throttle: Most automotive engines spend the largest part of their operational life running at part throttle and fuel delivery is calibrated to yield minimum consumption (maximum economy). • Full throttle: Mixtures containing a higher proportion of fuel (richer) provide more power at the expense of economy. • Transition: Both gradual and sudden changes in engine speed and load require instantaneous mixture correction. Transition from open to closed throttle plate tends to give a higher proportion of fuel, whereas transition from closed to open tends to give a higher proportion of air. • Cold start: During cold start and warm-up phases of engine operation, the fuel condenses on the cold cylinders, creating a lean condition, resulting in incomplete combustion. To counteract this, the fuel mixture is enriched.Definition: A rich mixture contains more fuel than air in relation to the stoichiometric ratio. A lean mixture contains more air than fuel in relation to the stoichiometric ratio.8 Principles of engine operationThe fuel system must be able to quickly respond to and satisfy these widely varying operating conditions. The air/fuel mixture is referred to by the Greek letter λ (Lambda), and is generally referencing the air factor in the ratio. Listed below are several common λ operating ranges: • λ = 1: mixture is optimum (stoichiometric). • λ 1: mixture is rich (lacking air) typically in the range λ = 0.85 to 0.95. • λ 1: mixture has an excess of air; a lean mixture typically in the range λ = 1.05 to 1.30. • λ 1.30: mixture has too much air to support consistent combustion. On an engine at normal operating temperature, it is important to maintain λ = 1. This allows for optimal catalytic converter operation (although in actual practice, λ factors between 0.9 and 1.1 provide the best engine operation). Because of the importance of the fuel mixture under a variety of operating conditions, the air/fuel mixture must be adapted constantly. In modern fuel systems, a feedback loop using oxygen sensors for the primary input is used for this adaptation. The period of time after an engine start when the oxygen sensor is not at operating temperature, and therefore not used, is called open loop operation . This condition can occur after either a cold or warm start. Conversely, engine operation with a valid oxygen sensor signal is called closed loop operation. For more information on open loop operation and closed loop operation, please refer to the glossary.Note: For more information regarding oxygen sensor function, refer to the Motronic M2.9 component overview.9 Principles of engine operationFuel system, overview The fuel system is made up of numerous individual components. The purpose of these components is to insure delivery of the correct air/fuel mixture formation to the engine at the correct time. Components such as fuel pumps and carburetors represented the state-of-the-art technology in early systems, but mechanical limitations prevented further development. Although advantages of these systems include simplicity and relatively low cost, disadvantages are frequent maintenance, poor emissions, relative inefficiency, and the inability to be self-diagnosing. Due to limited interaction between individual components, control of fuel delivery was not precise enough to meet modern standards. The advent of solid-state electronics allowed improvements in many fuel system areas. Sensors were able to provide information on current engine operating conditions. A central control unit would then process the data, make the calculations, and signal the appropriate actuators that would, in turn, run the engine. This level of control far exceeded the abilities of a carburetor and its related mechanical systems, and led to widespread use of fuel injection.10 Principles of engine operationEvolution of Engine Management Systems Modern technology created a new perspective in how fuel and ignition system management is viewed. Starting with the Fox and the 100LS in 1975, Audi began replacing carburetors with fuel injection. The Bosch™ KJetronic™ fuel injection system that was used seems very basic by today’s standards, but it represented a giant technological leap forward at the time. Fuel delivery was by individual fuel injectors in a continuous flow with the fuel pump relay containing the only electronics in the system. The ignition continued to be handled by a breaker point distributor. Advances in computer technology, combined with new circuit designs, allowed electronic control of the fuel and the ignition in later version of these systems. Mixture control feedback through the use of oxygen sensors allows more precise metering of the fuel. Ignition system feedback through the use of knock sensors allows optimum spark timing. These feedback loops allowed engine operation to be continuously corrected to compensate for changing operating conditions. Digital data processing and micro-processor technology made it possible to take extensive operating information from sensors and other input sources, and convert it to program-mapcontrolled fuel injection and ignition data. Today, technology enables engine management systems to control not only emissions and driveability, but to constantly optimize engine torque as well.11 Principles of engine operationIgnition system, overview The ignition system’s function is to insure delivery of a correctly timed and sufficiently strong spark to ignite the air/fuel mixture. Electrically, the ignition system components are divided into two categories by voltage level. Components using battery or low voltage are classified as primary , and include the following: • Battery • Coil • Trigger (either breaker points or electronic) • Electronic signal amplification and advance control Components using high voltage are classified as secondary , and include the following: • Spark plugs and wires • Distributor cap, rotor • Ignition coil (spark plug side) System function Refer to the basic coil ignition with breaker points graphic at the bottom of this page. When the ignition is switched on, battery voltage is supplied to the low voltage or primary side of the ignition coil. A strong magnetic field is developed in the primary windings. When the Ground side of the coil is open (by breaker points or electronically), the magnetic field around the primary windings collapses and induces a higher voltage in the secondary windings.12 Principles of engine operationSimply stated, the ignition coil is a step-up transformer switched on and off by the trigger unit. The high voltage generated by the ignition coil is distributed to each spark plug in the proper order through the distributor cap as the distributor shaft turns. At the spark plug, the high voltage causes an electrical spark to arc from the center electrode to the Ground electrode and spark plug threads. The period of time that the negative side of the coil is grounded (points remain closed) is referred to as dwell. Dwell is the length of time the primary winding can generate a magnetic field. The longer the dwell time, the stronger the magnetic field. This results in a higher secondary voltage (stronger spark).13 Principles of engine operationIn a breaker point style ignition system , the ignition points are mounted to a movable mechanism in the distributor called the breaker plate. They are switched on and off by the action of a rubbing block working against lobes of a cam on the distributor shaft. The distributor shaft turns at the same speed as the camshaft (½ crankshaft speed). A condenser (also called a capacitor), is connected in parallel with the ignition points, and acts as a filter to prevent point arcing. The inherent drawback to the breaker points system is mechanical wear (requiring periodic maintenance). To eliminate this, the solid state ignition system was developed. By replacing the ignition points with a Hall sender, more consistent and reliable ignition system performance was attained.14 Principles of engine operationThe Hall sender is a solid-state, semi-conductor device mounted in the distributor housing. A rotating trigger wheel is passed between a magnet and a Hall-effect transistor (see Glossary). Windows in the trigger wheel allow the Hall-effect transistor to be exposed to the magnetic field causing current to flow through the transistor. When a shutter wheel vane blocks the magnetic field to the Halleffect transistor, current flow stops. Operating voltage is supplied by either an ignition control module or the engine control module. Through these control modules, the Hall sender switches off the ignition coil when current flows (exposed) and on when there is no current flow (blocked). Advantages include: • High speed switching • No mechanical wear • No maintenance The accompanying table highlights the performance advantages. Newer engine management systems take the Hall signal a step further, and combine it with computer control to provide even more precise spark control.15 Principles of engine operationIgnition advance It takes approximately 2 milliseconds (0.002 seconds) from the start of mixture ignition to complete combustion. This time remains consistent for all engine speeds, but the time available for the process to occur is reduced as engine speed increases (the piston is moving faster). For this reason, spark must be generated sooner. The process of starting the ignition spark sooner in the cycle is called ignition advance. Ignition advance must be adjusted to account for wide variations in engine operating conditions, with primary concern given to engine speed and engine load. At idle, the start of combustion can occur near the top of the compression stroke. This allows maximum combustion pressure to push the piston down during the power stroke. As engine speed increases, the spark must be generated sooner, so that maximum cylinder pressure will continue to occur as the piston starts down on the power stroke. In the basic ignition system described previously, the cam which operates the breaker points is connected to a mechanism where centrifugal fly-weights move the cams position in relation to the points position in the distributor. This allows the spark timing to change with engine speed. The faster the engine speed, the sooner the spark occurs. The breaker plate is also attached to a vacuum diaphragm. This allows the spark timing to change in relation to an engine vacuum signal that changes with engine load. Note: Spark ignition engines produce the greatest power, and are the most efficient, when ignition occurs just before the point of detonation.16 Principles of engine operationSpark plugs Spark plugs represent the end component in the ignition system. They must endure the high temperatures and pressures of the combustion chamber for millions of ignition operating cycles without failure. An important characteristic of any spark plug is its ability to dissipate heat. The electrode must get hot enough to burn off any carbon accumulation by the time the engine reaches operating temperature, but not hot enough to burn the insulator (or electrode). Classifications exist for hot, cold or anywhere in between. A cold spark plug is a one that transfers the heat from the combustion process rapidly through the threads to the head and cooling system. A hot spark plug is a one that transfers the heat from the combustion process slowly through the threads to the head and cooling system. Different engine types require spark plugs with different physical characteristics, as well as electrical characteristics, and are supplied by several different manufacturers. Since spark plug characteristics are specified for each particular engine type by the factory, it is advisable to stay within these recommendations. For the heat transfer process to the cylinder head to be effective, the spark plug must be properly torqued into a cold cylinder head (refer to AESIS). Note: To ensure the integrity of the ground through the threads, anti-seize or similar products should never be applied to the spark plug before installation.17 Principles of engine operationEmissions system, overview Air quality has been an environmental concern for many years. Pollution from numerous sources, combined with atmospheric conditions, resulted in the degradation of air quality in many of the industrialized areas of the world. The State of California recognized that automobile emissions contributed significantly to the rising levels of pollution, and enacted legislation to establish air quality standards for motor vehicles. Other states continue to adopt California emissions standards. Federal and state clean air legislation continued to be passed with California leading the rest of the nation. In an effort to reduce exhaust emissions, various parts of the fuel and ignition systems were modified. New systems were added and existing systems were modified to reduce tailpipe and crankcase emissions. Systems were also added to reduce emissions from the fuel tank and vent system. A basic emissions system has the following components: • Throttle positioners and dashpots • Exhaust gas recirculation • Oxidation catalytic converters • Oxygen sensors • Secondary air injection • Intake air pre-heating • Evaporative emissions (fuel tank) • Crankcase emissions18 Principles of engine operationIt was soon clear that a more advanced means of managing fuel, air and ignition was needed to meet the changing Federal and State emissions requirements and fuel economy standards. Excellent driveability, performance and economy had to be maintained, and at the same time ensuring low exhaust emissions. Testing indicated that fuel vapor escaping into the atmosphere contained more hydrocarbons than the exhaust emissions of the vehicle. As a result, the Evaporative Emissions (EVAP) return system was added to minimize the amount of fuel vapor released. Vapors are stored in a charcoal canister, and then passed along via the EVAP canister purge regulator valve to the engine to be consumed in the combustion process. Current Motronic engine management systems also use a Leak Detection Pump (LDP) to pressurize the evaporative return system to insure the integrity of the system (checks for leaks). Fuel vapors that escape to the atmosphere are reduced to a minimum. Systems after 1998 include On board Refueling Vapor Recovery (ORVR) systems to control fuel vapor emissions during refueling. All of these efforts are contributing to the reduction of harmful pollutants that escape into the atmosphere. For more information, see SSP 941903, EVAP Systems, Operation and Diagnosis.19 Principles of engine operationThree-way Catalytic Converter, overview The catalytic converter is a major component in exhaust emission control “downstream” of the combustion process. Development and common usage of this device began with open-loop versions of carburetor and fuel injection systems in the 1970s. Closed loop engine management systems required by current legislation in the United States and Canada insure that almost all internal combustion engined vehicles are equipped with this important component. A catalyst, by chemical definition, is any substance that promotes, accelerates, or initiates a chemical reaction without being consumed in the reaction itself. In the case of the automotive catalytic converter, the active catalyzing agents are platinum, rhodium, and/or palladium. For maximum efficiency, the internal surface area exposed to the exhaust flow must be as large as possible. For that reason, the noble metals are deposited by evaporation onto a ceramic or metallic sub-structure called a monolith. The monolith is a long-channel honey-comb shaped structure with a large surface area contained in a high temperature steel housing. The surface area is increased even more through a process where a “washcoat” is applied. Other types of converters are used by other automotive manufacturers, but all Audis use the ceramic or metallic monolith design. Catalytic converters operate most efficiently at high temperatures and are usually placed in the exhaust stream as close to the engine as possible. A modern three-way catalytic converter is so named because it takes the three major automotive pollutants and reduces and oxidizes them into relatively harmless substances that do not contribute to air pollution.20 Principles of engine operationCatalytic Converter Operation The three-way catalytic converter takes the major exhaust pollutants of: • NON (nitrous oxides- several) • HC (hydrocarbons) • CO (carbon monoxide) and breaks them down into their component chemicals through a two-part process. The first part of the operating process is the catalytic reduction of the NON component. This phase reduces the nitrous oxides to their basic elements of nitrogen and oxygen. Since the air we breath is roughly 78% nitrogen, this is an acceptable result. The liberated oxygen is roughly 21% of the air and it too, is acceptable. However, the oxygen remains in the converter where it is used for the oxidation part of the process. The second part of the operating process is the catalytic oxidation of the HC and CO components. This phase combines the oxygen from the previous phase with the oxygen already contained in the monolith to produce water and carbon dioxide. Both of these compounds are essentially harmless. The output from a normally operating threeway catalytic converter consists primarily of: • N (nitrogen) • CO (carbon dioxide) • H O (water) The reduction process is most efficient in a low O environment, and the oxidation process is most efficient in a high O environment. It is the job of the engine management system to regulate the exhaust gas mixture to obtain the optimum environment for the reduction and oxidation process to occur. For maximum efficiency within the converter, lambda (λ) must be at 0.99 or 1.00 for both reactions. This operating range is referred to as the lambda (λ) window. The data required for this closed-loop control process is provided by the oxygen sensors (illustration on previous page). Oxygen sensor functionality varies by engine management system. Please refer to the appropriate chapter for system specific oxygen sensor information.21 Principles of engine operationOn Board Diagnostics On Board Diagnostic (OBD) capability allows the Engine Control Module (ECM) to recognize faults that could indicate a problem with a component or associated wiring. When a fault is recognized, a Diagnostic Trouble Code (DTC) will be stored in DTC memory. Current federal regulations require that any fault that effects exhaust emissions sets a Diagnostic Trouble Code (DTC), and illuminates a Malfunction Indicator Light (MIL) to alert the operator of an emissions related failure. Engine Control Module (ECM) fault recognition Audi engine management systems have the ability to diagnose and identify several different component failure conditions, including: • Short circuit to Battery Positive (B+) • Open circuit/Short circuit to Ground Systems complying with OBD II regulations also identify implausible signals. An implausible signal is a reading that is considered out of range for operating conditions. This is covered in the OBD II section of this SSP. ECM inputs (sensors) and outputs (actuators) are powered in one of two ways: • The ECM supplies a ground signal and the B+ is supplied from the fuse/relay panel. • The ECM provides a reference voltage and monitors the voltage drop across the sensor’s resistance (e.g. engine coolant temperature sensor).22 Principles of engine operationComponent Ground controlled via ECM The following examples illustrate a solenoid valve in a circuit that receives a constant 12 Volt source from the fuse/relay panel with component Ground controlled via the ECM. Normal operation of the component is checked by the self diagnosis circuitry in the ECM. The ECM monitors the voltage drop. This will change from 12V when the solenoid is in-active (open circuit voltage) to approximately 0V when the solenoid is active (voltage drops across the consumer).If selfdiagnosis circuitry does not see the correct voltage drops during operation of the component, the appropriate DTC is stored. Short circuit to B+ If a short circuit exists in the wiring harness, harness connector, or the component, the input to the ECM is a constant positive voltage. The ECM recognizes this as an abnormal condition, and a DTC is stored. Scan tool display: • Short circuit to positive (B+) Open circuit/Short circuit to Ground If an open or short circuit exists in the wiring harness, harness connector, or the component, the input to the ECM is a constant Ground (0 Volts). The ECM recognizes this as an abnormal condition, and a DTC is stored. To determine the exact failure, additional testing is required. Scan tool display: • Open circuit/ Short circuit to Ground23 Principles of engine operationComponent power (B+) controlled via ECM The following examples illustrate a temperature sensor in a circuit that receives a constant 5 Volt reference source from the ECM. It also can receive a Ground from a variety of sources for signal accuracy. In this type of circuit, as the temperature changes the resistance changes, resulting in a varying voltage drop across the sensor. During normal operation the self diagnosis circuitry monitors the 5V reference and the voltage drop across the component. The ECM “watches” for a valid signal, which varies by component, but will not equal either 0 or 5 Volts. If Battery +, Ground or the 5V reference is seen by the ECM, an appropriate DTC is set. Short circuit to Ground A break in the wiring harness insulation short circuits the 5 Volt output to Ground. The input to the ECM is a constant Ground (0 Volts). The ECM recognizes this as an abnormal condition, and a DTC is stored. Scan tool display: • Short circuit to Ground Open circuit/Short circuit to B+ If an open or short circuit exists in the wiring harness, harness connector, or in the component itself, the input to the ECM is a constant 5 Volts. The ECM recognizes this as an abnormal condition, and a DTC is stored. Scan tool display: • Open circuit/ Short circuit to B+24 Principles of engine operation - ReviewReview 1. Technician A says that Motronic engine management systems can identify short circuits to positive with some system components. Technician B says that Motronic engine management systems can identify short circuits to Ground with some system components. Which Technician is correct? a. b. c. d. 2. Technician A only Technician B only Both Technician A and Technician B Neither Technician A nor Technician B 6. 5. 4. Which of the following components is NOT a component of gasoline’s ability to pre-ignite? a. b. c. d. Research octane number Motor octane number Cetane Anti-knock indexWhich of the following is NOT a component failure condition recognizable by the scan tool? a. b. c. d. Short circuit to positive Short circuit to neutral Short circuit to Ground Open circuitWhich of the following is NOT an operating requirement for efficient operation of the Three Way Catalyst? a. b. c. d. High operating temperature. Lambda (λ) window of 0.99 to 1.00. Gasoline without lead or lead compounds. Gasoline with a minimum octane of 87 AKI.Technician A says that the ignition coil is part of both the primary and the secondary sides of the ignition system. Technician B says that the distributor rotor is part of the primary side of the ignition system. Which Technician is correct? a. b. c. d. Technician A only Technician B only Both Technician A and Technician B Neither Technician A nor Technician B3.In the four-stroke gasoline engine, the camshaft turns at what speed in relation to the crankshaft? a. b. c. d. Twice crankshaft Same as crankshaft ¼ crankshaft ½ crankshaft 7.Which of the listed exhaust by-products is NOT harmful to the atmosphere? a. b. c. d. Hydrocarbons (HC) Oxygen (O ) Carbon monoxide (CO) Oxides of Nitrogen (NON)25 Notes26 Continuous Injection Systems (CIS)Continuous Injection SystemIn 1975, Audi introduced Bosch K-Jetronic™ fuel injection on the 100 LS model. This class of fuel injection system is characterized by the continuous flow of fuel from the fuel injectors and is more commonly known as CIS (Continuous Injection System). Audi used several versions of this hydromechanical fuel system due to its efficient and consistent engine operation. • CIS: Completely hydro-mechanical with the fuel pump relay being the only electronic component. • CIS-Lambda: Similar in operation to CIS, but with an oxygen sensor providing feedback to an electronic control unit which continuously adjusts mixture. • CIS-E: Electronic system with sensors providing engine operating data to an electronic control unit, and an oxygen sensor providing mixture feedback information. Idle speed is controlled electronically by a variable throttle bypass valve called an idle air control valve, or idle stabilizer. • CIS-E III: An engine management system similar to CIS-E, but with electronic ignition and integrated knock regulation. Also features electronic fault recognition and memory. • CIS Turbo: An engine management system combining the CIS lambda fuel system with electronic ignition and boost control. Later versions added knock sensors to the ignition system. • CIS-E Motronic: An engine management system, similar to CIS-E III, but with adaptive mixture control.27 Continuous Injection Systems (CIS)CIS Continuous Injection System (CIS) operates by controlling fuel flow rates and variable pressures to the fuel injector. As the name implies, the fuel injectors are continuously injecting fuel. When the intake valve is closed, the fuel is stored in the intake port. Opening the valve allows the stored fuel to be pulled into the cylinder. Fuel for the injectors is provided by the fuel distributor. This component is directly linked to the air flow sensor. Any increase in airflow provides a proportional increase in fuel flow to the injectors. The control pressure regulator supplies pressure to the top of the control plunger, and depending on how much pressure is applied, will create a resistance for the plunger to rise, affecting the fuel mixture. Example: On a cold start, control pressure is 0.5 bar. As a result, there is little resistance for the plunger to rise with movement of the air flow sensor. As operating temperature rises, control pressure increases to 3.7 bar. Resistance is greater, resulting in a leaner fuel mixture.28 Continuous Injection Systems (CIS)Baseline air/fuel mixture is accomplished by adjusting the rest position of the control plunger. The design of the system is such that the fuel mixture will scale according to this baseline setting. Cold start enrichment is handled by a separate electrically operated fuel injector mounted in the intake manifold. Power is provided via terminal 50 from the ignition switch. The Ground is completed through a Thermotime switch mounted in the cylinder head. The Thermo-time switch has a bi-metallic strip that is heated by 12 V also supplied by starter terminal 50. Heating the strip causes it to flex and open the circuit. This “timer” circuit allows for a temperature sensitive quantity of fuel to be injected during cranking of the engine. If coolant temperature is above approximately 35°C, the heat of the engine will not allow the cold start injector to operate. Additional airflow during cold running is handled by an auxiliary air bypass valve. A heated bi-metallic strip opens a passage in the valve. This allows a controlled excess of air during the warm-up period of the engine. As the engine enters warm running the passage is closed and idle air quantity defaults to a bypass channel in the throttle valve housing. Since there are essentially no electronic controls to this system, there are no sensors or actuators. Additional systems Fuel is supplied to the CIS system by an externally mounted fuel pump with an accumulator and filter on the outlet side. Pressure is maintained by a fuel pressure regulating relief valve integral with the fuel distributor.29 Continuous Injection Systems (CIS)K-Jetronic with Lambda control In 1980, CIS fuel injection was modified to better meet exhaust emission standards. The addition of an oxygen sensor allowed the fuel system to adapt to instantaneous running conditions. This provided more consistent running characteristics, as well as minimizing the amount of adjustment necessary to the system. The control unit is able to adjust fuel trim by continually modifying the differential pressure between the upper and lower chambers of the fuel distributor. A solenoid valve (frequency valve) is installed inline between the system pressure from the lower chamber and the fuel return line. When lower chamber pressure drops, the diaphragm flexes downward, opening a larger fuel orifice.30 Continuous Injection Systems (CIS)After the engine has reached operating temperature it enters closed loop operation (see Glossary). The control unit pulses the frequency valve with a varying duty cycle, thus varying the differential pressure. The baseline air/fuel mixture is no longer set be means of sampling pre-catalyst exhaust gases. A test connector is provided to test the duty cycle of the valve. During closed loop operation the duty cycle should fluctuate between 45%-55%. The fluctuations follow the voltage output of the oxygen sensor. The Lambda control unit receives input from the oxygen sensor, as well as an idle and full throttle switch. CIS with Lambda control was also available with a turbocharger on early 5000 models. The turbocharger added additional air to the engine which improved performance by making use of heat that would be otherwise wasted. A mechanical wastegate limited boost pressure, but fuel control remained essentially the same. This system was the beginning of today’s adaptive engine management systems. Inputs/Sensors The addition of an Oxygen sensor control unit required a minimum number of input signals including: • Oxygen sensor thermo-switch (to switch off oxygen sensor control on a cold engine) • Oxygen sensor • Full throttle enrichment switch Outputs/Actuators Only one output signal is generated: • Oxygen sensor frequency valve31 Continuous Injection Systems (CIS)CIS-E Beginning in 1984, Audi expanded the capabilities of the CIS fuel injection system. New features include: • Control pressure regulator and frequency valve replaced by an Differential Pressure Regulator (DPR). • Electrically heated oxygen sensor (allows for faster closed loop operation). • Air flow sensor potentiometer (more accurate control of Lambda). • Altitude sensor (varies fuel trim with barometric pressure). • Idle stabilizer valve (more stable idle characteristics). • Fuel system pressure now regulated by an external fuel pressure regulator.32 Continuous Injection Systems (CIS)The major difference between CIS-Lambda and CIS-E is the replacement of the control pressure regulator and frequency valve with an electro-hydraulic actuator. This actuator is more commonly called a Differential Pressure Regulator (DPR). The differential pressure regulator receives a varying current signal from the CIS-E control unit. This energizes an electro-magnet, which deflects a valve plate to create a difference in the pressures between the upper and the lower chambers of the fuel distributor. As current is increased, the plate valves deflects more which restricts fuel flow to the upper chamber of the fuel distributor. The reduction in fuel pressure in the lower chamber causes the pressure regulating valves at the fuel injector outlets to open further, increasing the quantity of fuel delivered to the injectors. This increases fuel pressure to the injectors and allows greater fuel flow for a given amount of sensor plate travel. The operating range of the differential pressure regulator during oxygen sensor control is between 0 mA and +20 mA, allowing for more accurate control of the fuel trim, as well as decreased maintenance. Continuous, variable control of idle speed is built into the CIS-E fuel injection system. This is accomplished by regulating the flow of air around the throttle valve by an electronically controlled bypass valve called an idle air control valve or idle stabilizer. Compensation is made for differing engine load conditions such as those encountered with a cold engine or when the air conditioning is switched on. The idle air control valve replaces the function of the auxiliary air regulator.33 Continuous Injection Systems (CIS)Inputs/Sensors CIS-E fuel injection control units require several sensor inputs to calculate the current value required by the differential pressure regulator. These signals include: • Engine coolant temperature sensor • Airflow sensor potentiometer • Oxygen sensor • Engine RPM signal from ignition control unit • Idle switch • Full throttle enrichment switch Outputs/Actuators Output signals generated are: • Differential pressure regulator • Idle stabilizer34 Continuous Injection Systems (CIS)CIS-E III Model year 1987 brought the next changes in CIS-based fuel injection systems. CIS-E III added a separate knock sensor control unit with On Board Diagnosis through blink codes displayed in the instrument cluster. The operating range of the differential pressure regulator during oxygen sensor control has been modified. The new range is between -10 mA and +10 mA with an adjusting point of 0 mA. This allows better engine operation in the event of an electrical failure and minimal ECM correction to a properly adjusted engine. The addition of knock control allows the engine to operate at a higher level of efficiency. This is accomplished by optimizing the combustion process according to fuel grade. Inputs/Sensors CIS-E III fuel injection and ignition control units require several sensor inputs to calculate the values required for engine operation. These inputs include signals from: • Engine coolant temperature sensor • Airflow sensor potentiometer • Oxygen sensor • Hall sender in the ignition distributor • Knock sensor • Altitude sensor • Idle and full throttle switches35 Continuous Injection Systems (CIS)Outputs/Actuators Output signals generated to operate the engine include: • Differential pressure regulator signal • Idle stabilizer signal • Carbon canister shut-off valve signal • Cold start valve signal • Ignition signal to the power output stage • Malfunction indicator light On Board Fault Memory CIS-E III engine management systems have the ability to store information concerning certain component malfunctions in memory. Faults are stored in either the ignition control module or the fuel injection control module. Any malfunctions recorded will be erased when the ignition is switched off. The system can recognize approximately 17 different 4-digit fault codes, and the fault memory can be accessed using scan tool VAG 1551. Model year 1988 vehicles require the use of adaptor VAG 1550/2 with system access through a connection to the fuel pump relay. Later vehicles access this data through the data link connector (DLC). Sensor inputs, actuator signals and other output signals are shown in the illustration on the following page.36 Continuous Injection Systems (CIS)37 Continuous Injection Systems (CIS)CIS Turbo 1983 was a landmark year for Audi with the introduction of its first engine management system. CIS Turbo integrated both fuel injection and ignition timing into one control unit. The early fuel/timing control unit, commonly referred to as the MAC-02, used inputs from the following sensors for engine control: • Intake air temperature • Engine coolant temperature • Boost pressure transducer (integral with the fuel/timing control unit) • Engine speed sensor • Crankshaft position (reference) sensor • Camshaft position (Hall sender in distributor) • Oxygen sensor • Idle/full throttle switches The signals generated to operate the engine included outputs to the following: • Ignition control unit • Frequency valve • Fuel pump relay Ignition timing was controlled by a calculation map derived from engine RPM, boost pressure, and intake air temperature. In 1986, several modifications were made with the addition of a new control unit known as the MAC-07. A new single knock sensor allowed optimized ignition timing, and minimized the possibility of engine knock under boost. A wastegate frequency valve was also included giving more accurate control over total boost pressure. This component functioned at the command of the ECM by supplying boost pressure to the upper chamber of the wastegate. The pressure acting on the wastegate diaphragm controlled wastegate operation. The final change to CIS Turbo was mid year 1989. The newest control unit, MAC-11, added a second knock sensor for even more accurate control of ignition timing. On board diagnostics for this system were limited. Several fault indicators can be read through tachometer needle position on the instrument cluster on some models only.38 Continuous Injection Systems (CIS)CIS-E Motronic With the introduction of the 4-cylinder Audi 80 and 90 models in the North American market, CIS fuel injection systems evolved into CIS-E Motronic engine management. This system and its individual components are very similar to CIS-E III in operation, but combine fuel injection control and ignition control into a single electronic Engine Control Module (ECM). Located behind the air conditioner evaporator assembly, the 35-pin CIS-E Motronic ECM features encompass: • Fuel injection control • Ignition control by ECM map • Individual cylinder selective knock regulation • Oxygen sensor regulation with adaptive learning • Idle speed control • Fuel tank ventilation control • Permanent fault memory via blink code The operating range of the differential pressure regulator during oxygen sensor control has been expanded due to the adaptive learning capability (see Glossary). The rich adaptive limit is +23 mA, and the lean limit is -16 mA. This new capability allows the engine management system to compensate for changes in the engine’s operating conditions such as altitude changes, intake air leaks, or other deviations from normal running. The adaptive learning capability necessitates new procedures when engine settings need to be adjusted, since engine idle speed is preprogrammed into the ECM and cannot be adjusted.39 Continuous Injection Systems (CIS)Inputs/Sensors CIS-E Motronic engine management receives operating inputs from the following sensors: • Ignition distributor with Hall sender (engine RPM) • Air sensor potentiometer (engine load) • Idle and full throttle switches (throttle position) • Coolant temperature • Heated oxygen sensor • Knock sensor Additional input is received from the air conditioning system. Actuators/Outputs CIS-E Motronic engine management systems generate operating outputs to operate the following actuators: • Differential pressure regulator • Ignition coil power output stage • Cold start valve • Idle stabilizer • Carbon canister frequency valve • Carbon canister shut-off valve An signal is also sent to the instrument cluster for tachometer, dynamic oil pressure, malfunction indicator light, and the Auto-Chek system.40 Continuous Injection Systems (CIS)On Board Fault Memory Permanent fault memory as applied to CIS-E Motronic means that any malfunctions recorded will be retained when the ignition is switched off. Checking and clearing the fault memory is generally done during maintenance, or if the malfunction indicator in the instrument cluster is illuminated. The system can recognize up to 15 different 4-digit fault codes. The fault memory can be accessed using scan tool VAG 1551. Model year 1988 vehicles require the use of adaptor VAG 1550/2 with system access through a connection to the fuel pump relay. Later vehicles access this data through the data link connected (DLC). Sensor inputs, actuator signals and other output signals of the 1988 - 1992 Audi 80, 2.0 liter, engine code 3A are shown in the illustration on the following page.41 Continuous Injection Systems (CIS)42 Motronic M2.3.2 OverviewMotronic M2.3.2 OverviewSystem description Audi first introduced Motronic Engine Management on the 1990 V8 Quattro with the allaluminum 3.6 liter engine. For the 1993 model year, both the 20 Valve 5-cylinder 2.22 liter engine and the 4.2 liter V8 engine were equipped with Motronic M2.3.2. The Motronic Engine Management System combines all fuel, ignition and evaporative emissions system functions into a single electronic control unit. This electronic control unit is known as the Engine Control Module (ECM). The ECM governs all of the output devices responsible for running the engine, and operates other related system devices. Engine-mounted sensors continuously gather operating data and send this information to the ECM. This data is converted and processed within the ECM for use in determining the engine’s momentary operating conditions. This information is used as the basis for the ECM’s output signals, and sent to the system actuators. As on previous systems, engine management control is digital electronic, and is based on engine load and engine speed.43 Motronic M2.3.2 OverviewFunctional overview Motronic M2.3.2 uses engine speed and load as its primary inputs. An inductive sensor mounted on the cylinder block measures crankshaft speed at the flywheel, and provides the engine speed signal. A second induction sensor (mounted near the first) signals crankshaft position which provides a reference point. A Hall sender in the distributor provides camshaft position information to identify cylinder number one. This allows fuel injection to be sequential, and timed to the opening of the intake valve. Engine load information is received from the Mass Air Flow (MAF) sensor G70, which has no moving parts. All Audi engine management systems with oxygen sensor(s) adapt to changing conditions while the engine is running. The ECM uses the oxygen sensor signal to determine the oxygen content of the exhaust gases. It then determines if the injector opening time or duration needs to be lengthened or shortened to achieve the optimum air/fuel ratio of 14.7: 1. This is referred to as adaptation (see Glossary). Motronic M2.3.2 engine management takes oxygen sensor adaptation to the next level. Values obtained during engine operation are stored and used as the basis for engine operation on the next start. These stored values are said to be “learned” values, and can change or adapt as often as needed. The process of storing and using learned values is called adaptive learning (see Glossary).44 Motronic M2.3.2 OverviewIn addition to mixture adaptation, idle speed and ignition timing also adapt to changes in operating conditions (i.e. changes in altitude and small vacuum leaks). Note: If the battery is disconnected, or if power is interrupted to the ECM, all learned or adapted values will be erased. The ECM will start from a baseline setting and relearn and adapt to operating conditions. With the VAG 1551/1552 or VAS 5051 connected and set to Basic Settings (function 04), the Motronic system can be made to adapt to current conditions in several minutes. When the Basic Settings function is selected, the scan tool signals the ECM to: • disable the A/C compressor • disable the EVAP system • stabilize ignition timing and idle speed • stabilize idle speed Motronic engine management systems consist of, and perform the following functions: Sequential Fuel Injection • Fuel injection via map control • Starting enrichment • Controlled ignition system • After start enrichment • Acceleration enrichment • Fuel deceleration shut-off • Maximum engine speed limitation • Oxygen sensor control • Vehicle speed limitation (130 m.p.h.) Ignition timing via map control • Dwell angle control • Temperature correction • Starting control • Digital idle stabilization • Selective cylinder knock control Idle Air Control (IAC) • Idle air volume via Map control • Start control • Correction for A/C switched on • Correction for transmission in gear Exhaust Gas Recirculation (EGR) • EGR via map control • On Board Diagnostic (California only) Fuel Tank Ventilation • Fuel tank ventilation via map control Advantages of adaptive learning include: • optimal fuel economy and driveability • reduced emissions • reduced maintenance • Improved driveability Note: When diagnosing oxygen sensor adaptation faults, be sure to inspect the following: • Exhaust system (allows outside air to mix with exhaust gases and affect oxygen sensor readings) • Engine sealing (oil leaks can create false air leaks when the engine is running, causing un-metered air to enter the intake manifold) • False air leaks (can include Idle Air Control (IAC) valve, or associated intake manifold) Any of these areas, if not well sealed, can lead to an inaccurate air/fuel mixture, resulting in poor driveability and possible adaptation faults. Always check the basics first!45 Motronic M2.3.2 OverviewThe three illustrations show the normal window of operation for an engine management system, as well as a system that has adapted to a lean condition and a rich condition. The layout of the illustrations shows the fine control range of the fuel system on the right, with its corresponding position in the coarse range on the left. On the balanced system, the fuel trim is in the center of the graph. This means that the system has not adapted to any mechanical or component problems. The second illustration shows the effect on the adaptation window from an excess of unburned oxygen in the exhaust. Example: If a false air leak is introduced, the fuel system will register a lean running condition. The Motronic ECM will move the fine control range from 0% toward 100%, dependi