TECHNICAL DOCUMENTATION

SSP 941803 Audi 3,0-liter V6 TDI

PDFEN103 pages6 MB
SSP 941803 Audi 3,0-liter V6 TDI - PDF cover

This PDF is currently unavailable.

Read document text
Service TrainingAudi 3.0-liter V6 TDIWith Clean Diesel System Self-Study Program 941803 Audi of America, LLC Service Training Printed in U.S.A. Printed 03/2009 Course Number 941803 ©2009 Audi of America, LLC All rights reserved. All information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, Inc., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC. Always check Technical Bulletins and the latest electronic repair information for information that may supersede any information included in this booklet. Trademarks: All brand names and product names used in this manual are trade names, service marks, trademarks, or registered trademarks; and are the property of their respective owners. Table of ContentsIntroduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Engine Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Fuel System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Engine Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Exhaust Treatment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68 Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92 Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94 Knowledge Assessment . . . . . . . . . . . . . . . . . . . . . . . . . . . 99The Self-Study Program provides introductory information regarding the design and function of new models, automotive components or technologies. The Self-Study Program (SSP) is not a Repair Manual! All values given are intended as guidelines only and refer to the software version valid at the time of publication of the SSP. For maintenance and repair work, always refer to the current technical literature.ReferenceNotei Notesii IntroductionIntroductionThis Self-Study Program (SSP) describes the design and function of the 3.0 liter Clean Diesel TDI Engine and exhaust gas after-treatment system. When you have completed this SSP, you will know the following: –– Design and function of the 3.0 liter TDI engine –– The limits established by the emission standards for diesel engines in various countries throughout the world –– Which components are used in the exhaust gas after-treatment system –– The location and function of these components –– The influence of combustion chamber pressure –– The reason for heating the tank elements of the reducing agent at low ambient temperatures1 IntroductionAudi Introduces the Cleanest Diesel Technology World Wide into Standard ProductionThe systematic evolution of the TDI resulted with the development of the world’s cleanest diesels. The core components of this current TDI combustion system development include: –– The fuel injection system –– Comprehensively improved exhaust gas recirculation system –– Optimized turbocharging –– Integrated cylinder pressure control system As a first step, improvements to these systems help to significantly reduce the engine’s untreated emissions. In the second step, an active exhaust gas after‑treatment system reduces the oxides of nitrogen emissions to a minimum. Thus, by combining engine modifications with a new exhaust gas after‑treatment system, the Clean Diesel system makes it possible to efficiently minimize emissions while at the same time reducing fuel consumption. The objective is the further development of TDI technology to achieve emissions below the future EU6 limits, as well as below the most stringent LEV II/BIN5 limits, and to be ready for world-wide use.AdBlue® is a registered trademark of the Verbands der Automobilindustrie e. V. (VDA)2 IntroductionEmission StandardsThe guidelines specify the following emission limits for gasoline and diesel engines: –– Diesel engine particulates –– Unburned hydrocarbons (HC) –– Oxides of nitrogen (NOx) –– Carbon monoxide (CO)Emission LimitsParticulatesPercentageHC+NOxPercentageCOPercentage Limits g/km428_036LEV ULEV BIN5 = = = Low Emission Vehicle Ultra Low Emission Vehicle Super Ultra Low Emission Vehicle Exhaust standard for California and other US statesSULEV = The term “BIN” comes from the fact that the exhaust gases are collected and analyzed in bags during the exhaust tests. Depending on the specified emission standard, calculations go from BIN10 to BIN5.3 Engine MechanicalEngine MechanicalEngine-Related MeasuresThe 3.0 liter V6-TDI was based on and developed from the EU5 (European) engine. It is a modular extension of an existing engine with the following changes: –– An optimized two-stage chain drive that lowers the chain forces, reducing frictional losses –– An oil pump with flow rate-control and two pressure stages to reduce drive output required for lubrication High exhaust gas recirculation cooling performance is achieved by using a new EGR system with aluminum module technology. This measure also reduces the pressure loss in the exhaust gas recirculation path, which has a positive effect on the charge cycle and on fuel consumption. The injector system with a maximum injection pressure of 29,000 psi (2000 bar), optimized turbocharging, as well as a charge-air path with an integrated charge‑air cooler bypass permits the optimized temperature management of the air path. The combustion chamber pressure sensor for cylinder pressure-based combustion is also a new feature.4 Engine MechanicalTorque Curves BIN5268 (200) 241 (180) 215 (160) 188 (140) 160 (120) 134 (100) HP (kW) 80 (60) 479 (650) 443 (600) 406 (550) 369 (500) 332 (450) 295 (400) lb ft (Nm) 221 (300)1000 Engine Speed in RPM2000300040005000 Engine Speed in RPMOutput in HP (kW)Torque in lb ft (Nm)428_002-3SpecificationsBIN5Engine Code Letters Design Displacement cu in (cm3) Output HP (kW) Torque lb ft (Nm) Valves per Cylinder Bore in (mm) Stroke in (mm) Compression Ratio Firing Order Engine Management Fuel Exhaust StandardCATA 6-cylinder V Engine 181 (2967) 225 (165) @ 3500 – 4000 rpm 406 (550) @ 1750 – 2250 rpm 4 3.27 (83) 3.6 (91.4) 16.8 : 1 1–4–3–6–2–5 Bosch EDC 17 CP 24 US Diesel ULEV II/BIN55 Engine MechanicalMechanicsCrankcaseThe engine block is made of GGV-40 (vermicular graphite cast iron) with a cylinder gap of 90 mm. The cylinder bores undergo UV-photon honing for friction optimization and to minimize initial oil consumption. Note: UV photon honing involves using a laser beam to smooth the cylinder bores following honing. The laser beam, which is applied at high force, melts down the remaining metal nibs in the one-billionth range. A smooth cylinder bore is achieved immediately in this way rather than through the break-in process.325_005CrankshaftThe crankshaft is forged from temper-hardened steel and is supported by 4 main bearings. The upper end of the connecting rods are a trapezoidal design. The lower end of the connecting rods are cracked to ensure a precision fit and reduce movement of the bearing cap under load. The upper and lower bearing shells are not identical in composition. The upper bearing shell is a twocomponent composite while the lower shell is a threecomponent composite bearing.325_030PistonsCast pistons with a centrally arranged piston trough are used. They are cooled by injected engine oil via a ring channel. The pistons do not have valve pockets.325_0326 Engine MechanicalBalance ShaftThe balance shaft is located in the inner V of the engine block. The shaft goes through the engine and the balancing weights are secured at the ends. Driven by chain drive D, the balancer shaft turns at crankshaft speed opposite the direction of engine rotation.325_076Retaining FrameA retaining frame made of GGG 60 (spheroidal graphite cast iron) supports the crankshaft and serves to reinforce the crankcase.325_010Bolts/Main Bearing AssemblyTop Section of Oil PanThe division between the crankcase and the oil pan is at the middle of the crankshaft. The two-section oil pan is made up of an aluminium pressure-cast top section and a bottom section made of steel plate.325_0117 Engine MechanicalCylinder HeadFour valves per cylinder ensure optimum charging of the combustion chamber. In the V6 TDI, the valves are actuated by roller-type cam followers with hydraulic valve clearance compensation. The acoustics of the unit benefits from the use of the roller-type cam followers. These, together with the tensioned and play-compensated camshaft drive gears, reduce the mechanical noise of the valve train.Cylinder Head CoverCylinder Head Cover SealRetaining FrameCamshaftCamshaftsThe camshafts are manufactured from precision steel tubing using the IHU method.* The exhaust camshafts are driven by the intake camshafts by straight-toothed spur gears. * IHU – Internal High-pressure recastingValve TrainCylinder Head325_0348 Engine MechanicalTooth Profile Clearance CompensationThe spur gear of the exhaust camshaft (driven spur gear) comes in two parts. The wide spur gear is held on the camshaft through spring actuation and has three ramps at the front. The narrow spur gear has the corresponding grooves and is capable of both radial and axial movement. This is done to eliminate backlash between the gears.Spur GearsBelleville Spring Washer325_038325_039Note: Please refer to the current service literature for assembly instructions.A defined axial force is produced via a Belleville spring washer, where the axial movement is converted at the same time into a rotary movement with the help of the ramps. This offsets the teeth of the two driven spur gears, which in turn affects tooth clearance compensation.Installation PositionClearance Compensation325_065325_0669 Engine MechanicalChain Drive Valve Train AssemblyThe chain drive has been designed to minimize the loss to inner friction. Chain Drive B on the camshaft drive of Cylinder Bank 1 has been reshaped to increase the contact ratio of the camshaft gear that is now larger. At the same time, the gear ratio of the drive is modified making it possible to reduce the effort required for operation. Chain Drive D is modified in the balance shaft area making it possible to enlarge the engagement of the chain on the gear wheel. Chain Drive D drives the balance shaft at crankshaft speed against the normal rotation of the engine.New Camshaft Drive B New Chain Drive DCamshaft Drive CBalance ShaftCrankshaft Oil Pump Drive428_004Gold Chain = Old Chain Drive from previous EU5 Engine Silver Chain = Current Chain Drive10 Notes11 Engine MechanicalFlow Rate-Controlled Oil PumpThe use of a flow rate-control system reduces the required drive output of the oil pump. A vane pump is used in the new 3.0 liter V6-TDI engine; its delivery characteristics can be changed via a pivoted adjustment ring. This adjustment ring can be loaded with oil pressure via Control Surfaces 1 and 2 and swiveled against the force of the control spring. The ECM connects ground to the energized Oil Pressure Regulation Valve N428 in the lower rpm range, and the solenoid valve opens the oil duct leading to the second control surface of the adjustment ring. Both oil flows are now acting with identical pressure upon both control surfaces. The forces resulting from this are higher than those of the control spring and they cause the adjustment ring to swivel counterclockwise. The adjustment ring turns into the center of the vane pump and reduces the supply space between the vanes. The lower pressure level is switched depending on the engine load, engine speed, oil temperature, and other operating parameters, reducing the drive output of the oil pump.Oil Pressure Regulation Valve N428Oil Pressure SwitchCrankshaft Oil DuctLow Delivery RateControl Surface 1Adjustment Ring428_005Applied oil pressure from the crankshaft oil duct Delivery Chamber Vanes Control Surface 2 Control SpringMounting Flange428_00612 Engine MechanicalHigh Delivery RateStarting at an engine speed of 2500 rpm or a torque of 300 Nm (wide open throttle acceleration), Engine Control Module J623 disconnects Oil Pressure Regulation Valve N428 from the ground connection thus closing the oil duct to Control Surface 2. The applied oil pressure is now acting on Control Surface 1 only and acts with a lower pressure against the force of the control spring.De-energized SolenoidThe control spring swivels the adjustment ring clockwise around the mounting flange. The adjustment ring now swivels out of the center position and increases the delivery space between the individual vanes. More oil is delivered by increasing the spaces between the vanes. A resistance builds up against the higher oil volume flow due to the oil bores and the bearing clearance of the crankshaft, which lets the oil pressure increase. This makes it possible to implement a flow ratecontrolled oil pump with two pressure stages.Oil Pressure Curve @ 212°F (100°C)72.5 (5.0) 65.2 (4.5)Oil Pressure psi (bar)58.0 (4.0)50.8 (3.5)43.5 (3.0) 36.3 (2.5) 29.0 (2.0) 750 1000 1500 2000 2500 3000 3500 4000 4500 4750428_009Engine RPM Solenoid Valve Closed Solenoid Valve Open (current applied)High Delivery RateControl Surface 1 Adjustment Ring at Maximum Delivery428_007Mounting FlangeDelivery ChamberControl Surface 2428_00813 Engine MechanicalAir IntakeIntake Manifold with Butterfly ValvesButterfly valves that can be regulated smoothly are integrated into the intake tract. These can be used to adapt the air movement according to the current engine speed and load with regard to emissions, consumption and torque/power.Exhaust Gas Recirculation FlowThe butterfly valve adjuster with potentiometer reports the current position of the butterfly valve back to the ECM.Exhaust Gas Recirculation UnitIntake PipeThrottle Position Adjuster Intake AirButterfly Valves 325_031 Electric Butterfly Valve AdjusterExhaust Gas Recirculation:This involves high-pressure exhaust gas recirculation. The entry of exhaust gasses into the intake tract counters the intake air flow, resulting in a constant mixture of fresh air and exhaust gas.Throttle Position Adjuster:The throttle is closed in order to stop the engine. This reduces the compression effect and achieves softer engine coasting. In addition, the exhaust gas recirculation rate can be increased through targeted, map-controlled closure.Note: The throttle and butterfly valves are opened in coasting mode to check the air flow sensor and balance the oxygen sensor.14 Engine MechanicalButterfly Valve ClosedButterfly Valve OpenTangential PipeSwirl Duct325_047325_048To optimize the torque and combustion, a closed swirl duct increases the swirl at low loads. When the engine is started, the butterfly valves are open and are only closed again at idle speed (duty cycle: approximately 80%). Continuous opening is performed from idle speed to approximately 2,750 rpm (duty cycle: approximately 20%).To optimize performance and combustion, an open swirl duct allows a high level of cylinder charging at high loads. The butterfly valves are always completely open at a speed of approximately 2,750 rpm or higher. The butterfly valve is also open both at idle speed and during coasting.Note: A replacement adjuster must be adapted with the Scan Tool to synchronize it with the butterfly valves.15 Engine MechanicalExhaust Gas Recirculation (EGR)The EGR system combines the EGR coolers, EGR valve, and EGR bypass in a single component. Due to the higher exhaust temperatures in the upper partial load range, increased EGR cooling performance becomes necessary. The exhaust gas recirculation path consists of the following: micro-catalytic converter, additional cooler, and cooler for exhaust gas recirculation temperature sensor, and electric water-cooled exhaust gas recirculation valve. A separate cooling channel is integrated into the housing on the valve side to cool down the bypass flap and the EGR valve. To prevent deposits in the EGR path, especially during operation with low-quality fuels with high aromatic hydrocarbon contents, a metal micro-oxidation catalytic converter is located at the beginning of the EGR path.To obtain the lowest possible temperatures for the recirculated exhaust, the exhaust gas recirculation cooler is connected to a separate low temperature coolant circuit (described on the following pages). The coolant is extracted directly at the radiator outlet and delivered to the exhaust gas recirculation cooler by an electric pump. The additional cooler is connected to the engine cooling circuit and makes it possible to nearly double the cooling performance. Both the EGR Cooler and the additional EGR Cooler connected in series have bypass flaps. This allows the demand controlled adjustment of the EGR cooling performance at specific load points. To reduce the carbon monoxide and hydrocarbon emissions, the flaps are set to bypass position (the exhaust gas does not go through either cooler) during the engine warm-up phase.Exhaust Gas Recirculation CoolerExhaust Gas Recirculation (EGR) Motor V338 EGR Temperature Sensor G98Bypass Flap Throttle Valve428_010Metal Micro-Oxidation Catalytic ConverterBypass FlapAdditional Exhaust Gas Recirculation Cooler Connected in Series16 Engine MechanicalSwitchable Exhaust Gas Recirculation ActuatorThe cooling performance of the exhaust gas recirculation cooler leads to a clear reduction in particle and nitrogen emissions. The diagrams below and on the next page show the efficiency of the exhaust recirculation system in two selected partial load points.Flow Through Exhaust Gas Recirculation Cooler – Additional EGR Cooler BypassedWhen the engine is in partial load operation, the bypass of the additional EGR cooler is open (exhaust gas does not flow through it). The bypass of the EGR cooler is closed and exhaust gas is directed through the cooler. The bypass flap for the EGR cooler is opened at approximately 1750 rpm. It is controlled by the ECM, based on mapped values.Bypass Flap428_047Particles05101520253035NOx (g/h)Earlier EU4 Standard EGR with Cooler EU6 17 Engine MechanicalFlow Through Additional EGR Cooler – Flow Through EGR CoolerThe additional cooler is opened with increasing load and resulting higher exhaust temperatures; thus both EGR coolers are in cooling mode. This allows an increase of the EGR rate. The exhaust gas temperatures are lower and nitrogen oxide emissions are further reduced.Exhaust Gas Recirculation Cooler428_048Additional EGR Cooler Bypass FlapThe bypass flap for the additional EGR cooler is opened at approximately 2200 rpm. It is controlled by the ECM, based on mapped values.050100150200250NOx (g/h)Earlier EU4 Standard 18 EGR with Cooler EU6 EGR Cooler and Additional EGR Cooler (EU6) Engine MechanicalCooling System1 27 2 5 6 7342625to8 92410 112322 12 21 20 19 18 17 1613to15 14428_018Legend Heated Coolant 1. Engine Coolant Temperature (ECT) Sensor G62 2. Bleeder Screw 3. Additional Exhaust Gas Recirculation Cooler 4. Exhaust Gas Recirculation Cooler 5. Change-Over Flap For Exhaust Gas Recirculation 6. Heater Core 7. From The Heater Core 8. To The Heater Core 9. Cylinder Head Bank 2 (Left) 10. Fuel Cooler (Fuel/Water) 11. Bleeder Screw 12. Coolant Regulator For Exhaust Gas Recirculation 13. Water Pump 14. Cooler For Fuel Cooling (Water/Air) 19 Cooled Coolant 15. Fuel Cooler Pump V166 16. Check Valve 17. Radiator 18. Engine Coolant Temperature (ECT) Sensor (on Radiator) G83 19. Bleeder Screw 20. Coolant Regulator For Exhaust Gas Recirculation 21. Coolant Thermostat 22. Exhaust Gas Recirculation (EGR) Cooler Pump V400 23. Alternator 24. Engine Oil Cooler 25. Cylinder Head Bank 1 (right) 26. Coolant Expansion Tank 27. Cap For Coolant Expansion Tank Engine MechanicalExhaust Gas Recirculation CoolingExhaust Gas Recirculation CoolerExhaust Gas Recirculation (EGR) Cooler Pump V400 Additional Exhaust Gas Recirculation Cooler Connected In SeriesExhaust Gas Recirculation Cooler Thermostat (Opens when Cooler Output Temperature Exceeds 158°F (70°C))428_062Coolant Regulator for Engine Circuit (Thermostat)Coolant Regulator for Exhaust Gas Recirculation (Opens at 131°F (55°C))Blue – from the engine cooling circuitRed – to the heater coreThe high efficiency of the radiator for exhaust gas recirculation is reached through its own low-temperature cycle in the cooling system. Exhaust Gas Recirculation Cooler Pump V400 activates after engine start up and supplies the EGR cooler with cold water directly from the main radiator. The coolant regulator for the EGR controls the temperature in the EGR cooler at a constant 131°F (55°C) independently from the outside temperature. The additional EGR cooler is connected in series to the main cooler. This additional EGR cooler is integrated into the engine cooling system circuit which is controlled at a temperature of 188°F (87°C).Fuel CoolingFuel Return Line from the Injector SystemCoolant Supply from the Expansion TankCooler for Fuel Cooling (Water/Air)Fuel Cooler (Fuel/Water)Fuel Return to the TankFuel Cooler Pump V166At high loads, the diesel fuel must be cooled to ensure injection quantity accuracy and to stay within exhaust emission limits. The fuel cooling pump starts to run at engine start.20428_028 Engine MechanicalVariable Vane Turbocharger OperationThe adjustable turbocharger uses air guide vanes to regulate the flow of exhaust gas into the turbine. In contrast to the exhaust gas turbocharger fitted with a wastegate bypass, the adjustable turbocharger produces pressure not only at the top end of the speed range but also across the full speed range. The fundamental principle here is that a gas will flow through a narrowed pipe more quickly than through a pipe without a restriction, provided that the pressure in the two pipes is equal.Advantages–– High engine output is available at the bottom end of the speed range since the exhaust gas flow is regulated by the adjustable vanes. –– The lower exhaust gas back-pressure in the turbine reduces fuel consumption at the top end of the speed range and also improves bottom-end power output. –– Exhaust gas emissions decrease because an optimum charge pressure and improved combustion is attained across the full speed range.Adjusting Ring Pilot Support Ring Shaft190_007Low Engine Speed and High Charge Pressure are RequiredThe cross-section of the exhaust gas flow is narrowed upstream of the turbine wheel by means of vanes. Since the exhaust gas is forced to pass through the restricted cross-section more quickly, the turbine wheel rotates faster. The high turbine speed at low engine speed generates the required charge pressure. The exhaust gas back-pressure is high.VanesControl LinkageHigh Engine Speed190_010The turbocharger cross-section is adapted to the exhaust gas flow. In contrast to the wastegate bypass, the entire exhaust gas flow can be fed through the turbine in this way. The vanes free a larger inlet cross-section, thereby ensuring that the required charge pressure is not exceeded. The exhaust gas back-pressure drops. The vanes are fitted together with their shafts onto a supporting ring. The pilot pins of each vane are engaged in an adjusting ring, which moves all vanes simultaneously. The adjusting ring is controlled by Turbocharger (TC) 1 Control Module J724 via a guide pin.Control Linkage Guide Pins21 Engine MechanicalTo allow a quick build-up of charge pressure at low speed and under full load, the vanes are set to a narrow inlet cross-section. The effect of the restriction is to speed up the exhaust gas flow, thus increasing turbine speed. The vanes are set at a steeper angle with increasing exhaust gas flow rate or if a lower charge pressure is required. When the inlet cross-section is enlarged, the charge pressure and the turbine output remain virtually constant. In emergency operation, the vanes are at their maximum angle, providing the largest possible inlet cross-section.Shallow Vane Angle = Narrow inlet cross-section of exhaust gas flowSteep Vane Angle = Large inlet cross-section of exhaust gas flow Direction of rotation of adjusting ring190_011190_012190_008190_009The small size of the compressor and turbine allows a high level of response with only a slightly reduced maximum output. Optimized mounting of the turbine shaft reduces frictional losses with cold engine oil during the warm upphase and causes, especially at high elevations and at cold ambient conditions, a more spontaneous response behavior. A flow silencer on the suction side and a dual-chamber flow silencer on the compressor outlet prevent flow noise associated with high supercharging pressures.Turbocharger (TC) 1 Control Module J724Dual-Chamber Flow Silencers Air Guide Vanes428_029Exhaust Temperature Sender 1 G235 22 Engine MechanicalCharge-air Cooling with Integrated Charge-air Cooler BypassControlling the charge-air temperature contributes to ensuring consistently low emissions at varying ambient temperatures. Since the charge-air coolers are highly efficient and they cool the compressed charge-air to near ambient temperatures (at low outside temperatures), a bypass is integrated into the air path for bypassing the charge-air cooler.TurbochargerThrottle ValveThree-way TubeLeft Charge-air CoolerCharge-air Cooler Bypass Right Charge-air Cooler428_015The bypass flap element consists of the flap housing and two flaps that are mounted at 90° angles on a common shaft. They permit continuous mixing of cooled air from the two charge-air coolers and heated air from the turbocharger. In the final positions of the flap, either only the heated air from the turbocharger or the cooled down air from the charge-air coolers is delivered into the intake manifold.The advantage of variable charge-air mixing is that the intake air temperature can be regulated to the desired specified value depending on the characteristic map through a variable mixture ratio. This permits constant thermodynamic boundary conditions for low-emission and low-consumption combustion. The Charge-air Pressure Sensor G31 with integrated Intake Air Temperature (IAT) Sensor G42 senses the charge-air temperature. It is installed just upstream of the throttle valve in the pressure hose.23 Engine MechanicalCold Engine, Low Outside TemperatureThe heated charge-air, coming from the turbocharger over the three-way tube, is delivered directly through the bypass flap to the intake manifold. This allows the oxidation catalyst, the particle filter, and the exhaust cleaning systems to activate quickly.Bypass Flap Element To the Intake ManifoldHeated Air from the Turbocharger428_017Engine Under Load, High Outside TemperatureStarting at approximately 1750 rpm, depending on the characteristic map, the amount of cooled charge-air is delivered to the intake manifold through a defined position of the bypass flaps. By closing the bypass flap, the direct path of the chargeair to the intake manifold is closed. The charge-air is directed to the intake manifold through the charge-air cooler.To the Intake ManifoldCooled Air from the Intake Manifolds428_01624 Fuel SystemFuel SystemCommon Rail Fuel Injection SystemThe common rail fuel injection system is a high-pressure accumulator fuel injection system for diesel engines. The term “common rail” means that all of one cylinder bank’s injectors have a common, high‑pressure fuel accumulator or rail. In this injection system, pressure generation and fuel injection are separate. The high pressure required for injection is generated by a separate high‑pressure pump. This fuel pressure is stored in a high-pressure accumulator (rail) and is made available to the injectors via short injector pipes. This fuel injection system’s characteristics include: –– The injection pressure can be selected almost infinitely and can be adapted to the engine’s operating status –– A high injection pressure up to a maximum of 29,000 psi (2000 bar) enables optimal mixture formation –– A flexible fuel injection process, with several pilot and secondary injection processes The common rail fuel injection system offers many options for adapting the injection pressure and the injection process to the engine’s operating status. It is designed to meet the ever increasing requirements for low fuel consumption, low exhaust emissions, and smooth running characteristics.High‑Pressure Accumulator (Rail), Cylinder Bank 1Connecting Pipe Between the High-Pressure Accumulators (Rails)High-Pressure Accumulator (Rail), Cylinder Bank 2Cylinder 1 – 3 Fuel Injectors N30, N31, N32351_064High-Pressure PumpCylinder 4 – 6 Fuel Injectors N33, N83, N8425 Fuel SystemFuel SystemFuel Metering Valve N290High-pressure Pump CP 4.2Pressure Holding ValveFuel Temperature Sensor G81 Temperature-Dependent Switch-overAuxiliary Fuel Pump V393Fuel FilterHigh Pressure (300 - 2000 bar) Low Pressure Return from the Injector (10 bar) 26 Fuel SystemFuel Pressure Sensor G247High-pressure Accumulator 1 (Rail)Fuel Injectors 4 – 6 N33, N83, N84High-pressure Accumulator 2 (Rail)Fuel Pressure Regulator Valve N276Fuel Injectors 1 – 3 N30, N31, N32Coolant OutletCoolant InletMechanical Crash Valve Fuel Cooler (Fuel/Water)Tank Transfer Fuel Pump (FP) G6 Storage Housing428_02627 Fuel SystemHigh-pressure Pump CP4.2The new high-pressure pump CP4.2 operates with an injection pressure of approximately 29,000 psi (2000 bar.) The pump is supplied with fuel by the Auxiliary Fuel Pump V393 downstream of the Transfer Fuel Pump (FP) G6. Two pump pistons are actuated alternately by the camshaft (two lobes).Fuel Metering Valve N290 High-Pressure Port 1Inlet Valve Fuel ReturnHigh-Pressure Piston Fuel FeedRoller ShoeRollerHigh-Pressure Port 2 Camshaft with Double Cam428_023The benefits of the new high-pressure pump are: –– Produces rail pressures of up to 29,000 psi (2000 bar) –– Has been adapted to deal with fuel quality issues –– Less force for pressure generation thanks to roller plunger –– Uniform stress on the pump toothed drive belt –– Greater efficiency thanks to volume control on the suction side via N290 –– Self-lubricating28 Fuel SystemHigh-pressure Pump Internal ComponentsOutlet ValveSuction ValveFuel Metering Valve N290Pump PlungerOverflow ValveDrive Shaft with Cams403_049The high-pressure pump is supplied fuel by Auxiliary Fuel Pump V393. At high engine speeds, the pump can deliver more fuel than the injectors can deliver. Fuel Metering Valve N290 helps reduce power consumption and unnecessary fuel heating. N290 is open when not powered. It works in conjunction with Fuel Pressure Regulator Valve N276 to regulate delivery and pressure.Overflow ValveThe fuel pressure in the low pressure area of the highpressure pump is regulated by the overflow valve. V393 delivers fuel from the tank at approximately 73 psi (5 bar) to the high-pressure pump. The overflow valve regulates the intake fuel pressure in the high-pressure pump at approximately 62 psi (4.3 bar) The fuel delivered by the additional fuel pump works against the piston and the piston spring of the overflow valve. At a fuel pressure above 62 psi (4.3 bar,) the overflow valve opens and allowing for return of the fuel. The excess fuel flows via the fuel return line into the fuel filter403_11129 Fuel SystemFuel Metering Valve N290The Fuel Metering Valve N290 is integrated into the high-pressure pump. It ensures that the fuel pressure is regulated as required in the high-pressure area. The Fuel Metering Valve N290 regulates the quantity of fuel which flows to the high-pressure pump. The advantage of this is that the high-pressure pump only has to generate the pressure which is required for the current operating situation. This reduces the high-pressure pump power consumption and avoids unnecessary fuel heating.Fuel Metering Valve N290Fuel Metering Valve N290 Function – Without CurrentWhen no current is supplied, the Fuel Metering Valve N290 is open. The control plunger is shifted to the left by the spring force, and releases the minimal cross-section to the high-pressure pump. As a result of this, only a small quantity of fuel enters the high-pressure pump compression chamber.428_023Pump PlungerOutlet ValveTo High- Pressure Accumulator (Rail)Inlet ValveReturn to Gear PumpControl Plunger Supply from Gear PumpFuel Metering Valve N290351_01330 Fuel SystemFuel Metering Valve N290 Function – InitializedTo increase the quantity inlet to the high-pressure pump, Fuel Metering Valve N290 is initialized by the Engine Control Module through a Pulse-Width-Modulated (PWM) signal. Due to the PWM signal, the Fuel Metering Valve N290 is pulsed closed. This results in a control pressure, which acts on the control plunger, downstream of the valve. Varying the on-off ratio changes the control pressure and therefore the position of the plunger. The control pressure decreases and the control plunger is shifted to the right. This increases the fuel inlet to the high-pressure pump.Pump PlungerOutlet ValveTo High- Pressure Accumulator (Rail)Inlet ValveReturn to Gear Pump Control PlungerUSupply from Gear PumptFuel Metering Valve N290351_088Effects of FailureThe engine output is reduced. The engine management system operates in emergency running mode.UfShort Pulse Width = Small Fuel Inlett Pw t PWM SignalsPWM signals are “pulse-width-modulated” signals. These are square-wave signals with a variable on-time and constant frequency. Changing the valve on-time for fuel metering, for example, enables the control pressure and therefore the position of the control plunger to be changed.351_124UfLarge Pulse Width = Large Fuel Inlett Pw tU = Voltage t = Time f = Cycle Duration (Frequency) tPw = Pulse Width (On-Time)351_12531 Fuel SystemHigh-Pressure Accumulator (Rail)A high-pressure accumulator (rail) is installed for each engine cylinder bank. The high-pressure accumulators are forged steel pipes. They have the task of storing the fuel required for injection for all of the cylinders at high pressure.DesignThe high-pressure accumulators are connected to each other by a pipe. The fuel inlet connection from the highpressure pump, the connections to the injectors and the Fuel Pressure Regulator Valve N276 are located on the cylinder bank 1 high-pressure accumulator. The fuel inlet connections from the connection pipe, the connections to the injectors, and the Fuel Pressure Sensor G247 are located on the cylinder bank 2 highpressure accumulator.FunctionThe fuel in the high-pressure accumulators is constantly at a high pressure. When fuel is drawn from the highpressure accumulators for injection, the pressure within the high-pressure accumulators remains virtually constant due to their large storage volume. The pressure fluctuations that arise due to the pulsating fuel supply to the high-pressure accumulator from the high-pressure pump are minimized by the high-pressure accumulator’s large storage volume.Connection to InjectorsFuel Pressure Regulator Valve N276High-Pressure Accumulator (Rail) Cylinder Bank 1Inlet from High-Pressure PumpConnecting Pipe Between the High-Pressure Accumulators (Rails)High-Pressure Accumulator (Rail), Cylinder Bank 2Cylinder 1 – 3 Fuel Injectors , N30, N31, N32Fuel Pressure Sensor G247High-Pressure Pump Cylinder 4 – 6 Fuel Injectors , N33, N83, N84351_06932 Fuel SystemFuel Pressure Sensor G247The Fuel Pressure Sensor G247 is located on the cylinder bank 2 high-pressure accumulator (rail). It determines the current fuel pressure in the high‑pressure area.Fuel Pressure Sensor G247FunctionThe Fuel Pressure Sensor G247 contains a sensor element, which is comprised of a steel membrane with expansion measuring strips. The fuel pressure reaches the sensor element via the high-pressure connection. In the event of a change in pressure, the steel membrane deflection changes, as does the resistance value of the expansion measuring strips. The evaluation electronics calculate a voltage from the resistance value and transmit this to the Engine Control Module. A characteristic curve stored in J248 is used to calculate the current fuel pressure.351_014Effects of FailureIn the event of Fuel Pressure Sensor G247 failure, the ECM employs a fixed, substitute value for calculation purposes. The engine output is reduced.Expansion Measuring StripsElectrical ConnectionEvaluation ElectronicsSteel MembraneHigh-Pressure Connection351_01533 Fuel SystemFuel Pressure Regulator Valve N276The Fuel Pressure Regulator Valve N276 is located on the cylinder bank 1 high-pressure accumulator (rail). The regulator valve is used to adjust the fuel pressure in the high-pressure area. To do this, it is initialized by the ECM. Depending on the engine’s operating status, the pressure is between 3,336 and 29,007 psi (230 and 2000 bar). If the fuel pressure in the high-pressure area is too high, the regulator valve opens, causing some of the fuel in the high-pressure accumulator to enter the fuel tank via the fuel return. If the fuel pressure in the high-pressure area is too low, the regulator valve closes, thereby sealing the highpressure area at the fuel return.Fuel Pressure Regulator Valve N276FunctionThe illustration below shows the regulator valve in the resting position (engine “off”). If the regulator valve is not initialized, the valve needle is exclusively pressed into its seat by the force exerted by the valve spring. The highpressure area is separated from the fuel return in this case. The valve spring is designed in such a way that a fuel pressure of approximately 1160 psi (80 bar) is attained in the high-pressure accumulator (rail).351_047Valve NeedleSolenoidElectrical ConnectionHigh-Pressure Accumulator (Rail) Valve ArmatureValve Spring351_074Return to Fuel Tank34 Fuel SystemRegulator Valve Opened MechanicallyIf the fuel pressure in the high-pressure accumulator is greater than the valve spring force, the regulator valve opens and the fuel flows into the fuel tank via the fuel return.351_087Regulator Valve Initialized (Engine “On”)To attain an operating pressure of 3,336 and 29,007 psi (230 and 2000 bar) in the high-pressure accumulator, the regulator valve is initialized by the ECM using a PWM signal. This leads to a magnetic field in the solenoid. The valve armature is picked up and presses the valve needle into its seat. The fuel pressure in the high-pressure accumulator is therefore opposed by a magnetic force in addition to the valve spring force. Depending on the on-off ratio of initialization, the flow cross-section to the return pipe and therefore the flow is varied. This also enables compensation for pressure fluctuations in the high-pressure accumulator.UtEffects of FailureEngine operation is impossible in the event of Fuel Pressure Regulator Valve N276 failure, because sufficiently high fuel pressure for fuel injection cannot be built-up.351_10635 Fuel SystemFuel Temperature Sensor G81The Fuel Temperature Sensor G81 is located in the fuel supply pipe to the high-pressure pump. G81 is used to determine the current fuel temperature.Fuel Temperature Sensor G81Signal UsageThe ECM uses the Fuel Temperature Sensor G81 signal to calculate the fuel density. This serves as a correction variable to calculate the injection quantity, to regulate the fuel pressure in the high-pressure accumulator, and to regulate the quantity inlet to the high-pressure pump. To protect the high-pressure pump against excessively high fuel temperatures, the Fuel Temperature Sensor G81 is located in the fuel supply system. In the event of excessively high temperatures in the fuel supply system, the engine’s output is limited in order to protect the high-pressure pump. As a result of this, the quantity of fuel to be compressed in the high-pressure pump is also indirectly reduced and the fuel temperature is lowered.Effects of FailureIn the event of Fuel Temperature Sensor G81 failure, the ECM employs a fixed substitute value for calculation purposes.S351_03136 Fuel SystemPressure Retention ValveThe pressure retention valve is a purely mechanical valve. It is located between the return pipes from the fuel injectors and the fuel system fuel return.Pressure Retention Valve351_090Fuel Return PipesTaskThe pressure retention valve maintains a fuel pressure of approximately 145 psi (10 bar) in the injector fuel return. This fuel pressure is required for fuel injector function.FunctionDuring engine operation, fuel flows from the fuel injectors to the pressure retention valve through the return pipes. At a fuel pressure in excess of 145 psi (10 bar), the ball is lifted from its seat counter to the pressure spring force. The fuel flows through the open valve into the fuel return to the fuel tank.Return from the Fuel InjectorsReturn to the Fuel TankPressure Spring351_071Ball37 Fuel SystemFuel Injectors (Injection Valves)The fuel injectors are installed in the cylinder head. They have the task of injecting the correct quantity of fuel into the combustion chambers at the correct time. The 3.0L V6 TDI engine has piezo-controlled fuel injectors. Piezo injector switching speed is approximately four times faster than that of a solenoid valve. In comparison with solenoid valve-controlled injectors, piezo technology has approximately 75% less moving mass at the injector needle. This results in the following advantages: –– Very short switching times –– Several injections per working cycle are possible –– Precise injection quantitiesStructure of an InjectorFuel Inlet (High-Pressure Connection) Electrical Connection Pin-Type FilterFuel Return Piezo ActuatorConnecting Plunger Valve Plunger Valve Plunger Spring Switching ValveRestrictor Plate Nozzle Spring Sealing Ring Injector Needle351_016 351_06138 Fuel SystemInjection ProcessThe very short switching times of the piezo-controlled fuel injectors enable flexible and precise control of the injection phases and injection quantities. As a result, the injection process can be adapted to engine operating requirements. Up to five partial injections can be carried out in a single injection process. At higher loads and engine speeds only one pilot injection is triggered in order to reduce exhaust emissions. No pilot injection takes place at full throttle and high engine speeds, because a large quantity of fuel has to be injected to achieve a high level of efficiency.Pilot InjectionA small quantity of fuel is injected into the combustion chamber prior to main injection. This leads to a rise in temperature and pressure in the combustion chamber. The main injection ignition time lag is therefore shortened, reducing the rise in pressure and pressure peaks in the combustion chamber. This leads to low combustion noise and low exhaust emissions. The number, time, and injection quantities of the pilot injection processes are dependent on the engine operating status. When the engine is cold and at low engine speeds two pilot injections are triggered for acoustic reasons.Main InjectionFollowing pilot injection, the main injection quantity is injected into the combustion chamber following a brief injection pause. The injection pressure level remains virtually identical throughout the entire injection process.Secondary InjectionTwo secondary injections are used to regenerate the diesel particulate filter. These secondary injections increase the exhaust gas temperature, which is necessary to burn the soot particles in the diesel particulate filter.Initialization Voltage (V)Injection (Rate of Injection)TimePilot InjectionsMain InjectionSecondary Injections351_11839 Fuel SystemPiezo ActuatorA piezo actuator is used to control the injectors. This is located in the injector housing, and is initialized through the ECM. The piezo actuator has a high switching speed, switching in less than one ten-thousandth of a second. The inverse piezo-electric effect is used to control the piezo actuator.Piezo Element with Voltage V AppliedPiezo Effect“Piezo” is a Greek word meaning “pressure.” Piezo elements are frequently used in sensor systems. Pressure applied to a piezo element produces a measurable voltage. This behavior on the part of a crystalline structure is called the piezoelectric effect.Change in Length Simplified Crystalline StructureInitial Length351_096Inverse Piezo-Electric EffectThe piezo-electric effect is employed in reverse form in a piezo-controlled actuator. When a voltage is applied to the piezo element the crystalline structure reacts by changing length.Piezo ActuatorThe piezo actuator is comprised of many piezo elements, so that switching travel is sufficient to control the fuel injector. With the application of a voltage, the piezo actuator expands by up to 0.0012 inch (0.03 mm). For comparison purposes, a human hair has a diameter of approximately 0.0024 inch (0.06 mm).Multiple Piezo ElementsConnecting Plunger351_017Note: The piezo actuators are initialized with a voltage of 110 – 148 V. Note the safety precautions in the current service information.40 Fuel SystemConnecting ModuleThe connecting module is comprised of the connecting plunger and the valve plunger. The connecting module acts in the same manner as a hydraulic cylinder. It hydraulically converts the piezo actuator’s very rapid longitudinal change and actuates the switching valve. Due to hydraulic force transmission, switching valve opening is dampened, and injection is therefore precisely controlled.Connecting Module in Resting PositionConnecting PlungerAdvantages of hydraulic force transmission:–– Low friction forces –– Damping of moving components –– Compensation of component longitudinal changes caused by thermal expansion –– No mechanical forces acting on the fuel injector needlesValve PlungerSwitching Valve351_018Hydraulic PrincipleThe connecting module is a hydraulic system in which both the forces and the plunger areas behave in relation to each other. In the connecting module, the area of the connecting plunger is greater than the area of the valve plunger. The valve plunger is therefore actuated by the connecting plunger’s force. The area ratio of the connecting plunger to the switching valve is several times higher. As a result, the switching valve can be actuated by the connecting module counter to the rail pressure. The pressure retention valve in the fuel return maintains a fuel pressure of approximately 145 psi (10 bar) in the connecting module. This fuel pressure serves as a pressure cushion for hydraulic force transmission between the connecting plunger and valve plunger.Connecting Module ActuatedFuel Return High Fuel PressureConnecting PlungerArea Ratios of the PlungersPressure CushionValve PlungerSwitching Valve351_10841 Fuel SystemFuel Injector in Resting PositionIn its resting position, the fuel injector is closed. The piezo actuator is not initialized. Fuel pressure is high in the control chamber above the fuel injector needle and at the switching valve. The switching valve is pressed into its seat by the high fuel pressure and the switching valve spring force. The high fuel pressure is therefore separated from the fuel return. The fuel injector needle is sealed by the high fuel pressure in the control chamber above the injector needle and by the nozzle spring force. The pressure retention valve in the fuel injector fuel return maintains a fuel pressure of approximately 145 psi (10 bar) in the fuel return.Piezo Actuator High Fuel PressureFuel ReturnSwitching Valve Nozzle Spring Switching Valve SpringInjector NeedleInjector NeedleNozzle Spring42351_019 Fuel SystemStart of InjectionThe start of injection is introduced by the ECM. To do this, it initializes the piezo actuator. The piezo actuator expands and transfers this movement to the connecting plunger. The downward movement of the connecting plunger builds up a hydraulic pressure in the connecting module, which acts on the switching valve through the valve plunger. The switching valve is opened by the connecting module hydraulic pressure, and releases the path from the high fuel pressure to the fuel return. The fuel in the control chamber flows into the return through the outflow restrictor. The fuel pressure above the injector needle falls abruptly as a result. The injector needle is raised, and injection begins.High Fuel PressureFuel ReturnPiezo ActuatorConnecting PlungerValve PlungerValve Plunger SpringSwitching ValveOutflow RestrictorInjector NeedleControl Chamber351_02043 Fuel SystemEnd of InjectionThe injection process ends when the piezo actuator is no longer initialized by the ECM. The piezo actuator returns to its original position. The two connecting module plungers move upward and the switching valve is pressed into its seat. The path from high fuel pressure to the fuel return is therefore sealed. Fuel flows into the control chamber above the injector needle via the inflow restrictor. The fuel pressure in the control chamber increases to the rail pressure again and closes the injector needle. The injection process is completed, and the injector is in its resting position again. The injection quantity is determined by the piezo actuator’s initialization duration and the rail pressure. The rapid piezo actuator switching times enable several injections per working cycle and precise adjustment of the injection quantity.High Fuel PressureFuel ReturnPiezo ActuatorValve PlungerSwitching ValveInjector Needle Inflow Restrictor351_109Control ChamberInjector Needle 44 Fuel SystemFuel Injector Delivery CalibrationFuel Injector Delivery Calibration (IDC) is a software function in the ECM for initializing the fuel injectors. This function is used to individually correct the injection quantity for each common rail fuel injection system fuel injector throughout the entire performance map range. The precision of the fuel injection system is improved as a result. Fuel injector delivery compensation balances out production differences. The objectives of this injection quantity correction are: –– Reducing fuel consumption –– Reducing the quantity of exhaust gas –– Smooth running characteristics Note: If a fuel injector (injection valve) is replaced, it must be matched to the fuel injection system. Fuel injector delivery calibration must be performed using Guided Fault Finding.Example of an IDC Code on a Fuel InjectorIDC ValueA seven-digit calibration value is printed on each fuel injector. This calibration value may be comprised of letters and/or numbers. The IDC value is determined on a test rig during fuel injector production. It denotes the difference from the nominal value, and therefore describes an injector’s fuel injection behavior. The IDC value enables the ECM to precisely calculate the initialization times required for injection for each individual fuel injector.IDC Value351_11745 Fuel SystemCylinder Pressure-Based Combustion ControlCylinder pressure-based combustion is another component used to achieve low emissions and at the same time achieve high fuel economy. The combustion chamber pressure sensor used in the 3.0 liter V6-TDI engine is a product by Beru, available under the designation PSG (Pressure Sensor Glow Plug). It adds the combustion chamber pressure sensor function to a metal glow pin and is installed in Cylinders 2 and 5. This provides the option of integrating this new functionality in the existing space of the cylinder head. The heating pin is supported in such a way that it can move in an axial direction within the glow pin housing. It transmits the cylinder pressure to a diaphragm via a push rod. The deformation of the diaphragm is registered through the change in resistance and processed in an integrated electronic system. The processed voltage signal is transmitted to the engine control unit for further evaluation.Diaphragm* (Piezo-Resistive Effect)Heating Pin Can Move in Axial Direction428_056BellowsCombustion Chamber Pressure SensorGlow FilamentCombustion Pressure* Diaphragm (piezo-resistive effect)428_020A silicon resistor is installed on the edge of a diaphragm.Cylinder pressure-based combustion permits the optimum adjustment of the injection point, and thus the pressure profile during combustion, to different fuel qualities and exhaust gas recirculation rates. The course of combustion is determined from the pressure signal of the combustion chamber sensor and the engine speed signal. Based on the deviation from the target/performance comparison, a correction value is determined with regard to the target combustion development, which causes an intervention in both the injection and the air system. The fuel quality, in particular the cetane rating, has a major effect on the course of combustion and the burn rate. With a low cetane rating, the ignition property of the fuel is reduced and thus the ignition delay is significantly increased. The point of 50% energy conversion moves in the “late” direction. This leads to incomplete or partial combustion.In engines without cylinder pressure-based control, combustion cannot be fully completed at very high EGR rates due to the high displacement towards late and retardation. This causes combustion conditions similar to misfiring. As a result, the HC and CO emissions rise drastically. The course of combustion is kept constant with the help of the cylinder pressure-based combustion control system and thus combustion is stabilized. To counteract the higher ignition delay, the start of injection is moved to an earlier time. In this way the HC and CO emissions can be kept at a near constant low level with lower cetane ratings, low load, and higher EGR rates.46 Notes47 Engine ManagementEngine Management System OverviewSensorsMass Air Flow (MAF) Sensor G70Engine Speed (RPM) Sensor G28Camshaft Position (CMP) Sensor G40Engine Coolant Temperature (ECT) Sensor G62 Engine Coolant Temperature (ECT) Sensor (on Radiator) G83Fuel Temperature Sensor G81 NOx Sensor Control Module J583Cylinder 2 Combustion Chamber Pressure Sensor G678 Cylinder 5 Combustion Chamber Pressure Sensor G681 Fuel Pressure Sensor G247 Throttle Position (TP) Sensor G79 and Accelerator Pedal Position Sensor 2 G185 EGR Potentiometer G212NOx Sensor 1 G295 (downstream of turbocharger)NOx Sensor 2 Control Module J881Brake Light Switch F and Brake Pedal Switch F47Heated Oxygen Sensor (HO2S) G39 Reducing Agent Tank Sensor G684 Reducing Agent Metering System Pressure Sensor G686Reducing Agent Temperature Sensor G685 Exhaust Gas Temperature (EGT) Sensor 3 G495 Catalyst Temperature Sensor 1 G20 EGR Temperature Sensor G98 Diagnostic Connection (DLC) Engine Control Module (ECM) J623Exhaust Gas Temperature (EGT) Sensor 1 G235 Exhaust Gas Temperature (EGT) Sensor 4 G648 Bank 1 Exhaust Gas Temperature (EGT) Sensor 2 G448 Differential Pressure Sensor G505 Additional signals: - - - 48 Cruise control system - Terminal post 50 Speed signal - Crash signal from the airbag control unit Requirement start on engine control unit (Keyless Entry Start/Stop Systems 1 + 2)Private CAN busCharge-air Pressure Sensor G31 and Intake Air Temperature (IAT) Sensor G42NOx Sensor 2 G687 * Engine ManagementActuatorsFuel Injector for cylinders 1 – 3 N30, N31, N32Fuel Injector for cylinders 4 – 6 N33, N83, N84Automatic Glow Time Control Module J179 Glow Plugs 1 – 3 Q10, Q11, Q12 Glow Plugs 4 – 6 Q13, Q14, Q15Oil Pressure Regulation Valve N428Throttle Valve Control Module J338Fuel Metering Valve N290 Fuel Pressure Regulator Valve N276 Exhaust Gas Recirculation (EGR) Cooler Pump V400Exhaust Gas Recirculation (EGR) Motor V338Exhaust Gas Recirculation (EGR) Cooler Switch-Over Valve N345Exhaust Gas Recirculation (EGR) Cooler Switch-Over Valve 2 N381Turbocharger (TC) 1 Control Module J724Intake Flap Motor 1 V157, Intake Flap Motor 2 V275Additional signals: Air conditioning compressor Auxiliary coolant heater Fan settings 1 + 2 Auxiliary Air Heater Heating Element Z35 Left/Right ElectroHydraulic Engine Mount Solenoid Valves N144, N145Charge-air Cooler Bypass Control Unit J865Reducing Agent Metering System Control Module J880* Reducing Agent Injector N474 Reducing Agent Pump Heater Z103 Reducing Agent Line Heater Z104 Reducing Agent Pump V437 Reducing Agent Transfer Pump V436 Reducing Agent Tank Heater Z102Fuel Cooler Pump V166 Oxygen Sensor (O2S) Heater Z19 Fuel Pump (FP) Relay J17 Transfer Fuel Pump (FP) G6 Auxiliary Fuel Pump Relay J832 Auxiliary Fuel Pump V393428_02549 Engine ManagementControl Modules in the CAN Data BusThe schematic shown below shows the integration of the Engine Control Module (ECM) J623 into the vehicle’s CAN data bus structure.J623J217J104J234J285 J533J197J428J492J527J518351_115Drive CAN Data BusJ519J255Convenience CAN Data BusCAN Data Bus LineDrive CAN Data Bus:J623 J217 J104 J234 J197 J428 J492 Engine Control Module (ECM) Transmission Control Module (TCM) ABS Control Module Airbag Control Module Level Control System Control Module Distance Regulation Control Module All Wheel Drive Control ModuleConvenience CAN Data Bus:J285 J527 J518 J519 J255 J533 Instrument Cluster Control Module Steering Column Electronic Systems Control Module Access/Start Control Module Vehicle Electrical System Control Module Climatronic Control Module Data Bus On Board Diagnostic Interface50 Engine ManagementSensorsEngine Speed (RPM) Sensor G28The Engine Speed (RPM) Sensor G28 is secured to the gearbox housing. It is an inductive sensor, which samples a 60-2 sensor wheel, which is secured to the drive plate. A segment gap on the sensor wheel serves the Engine Speed (RPM) Sensor G28 as a reference mark.Engine Speed (RPM) Sensor G28 2-Segment GapSignal UsageThe engine speed and the precise position of the crankshaft are recorded via the sensor’s signal. This information is used by the ECM to calculate the injection point and the injection quantity.Effects of FailureIn the event of signal failure, the engine is shut off and can no longer be started.351_021Drive Plate60-Segment Sensor WheelCamshaft Position (CMP) Sensor G40The Camshaft Position (CMP) Sensor G40 is secured in the retaining frame of the cylinder bank 1 cylinder head. It scans the sensor wheel on the camshaft, with which the position of the camshaft is detected.Signal UsageThe sensor signal is required by the ECM to detect the first cylinder when starting the engine.Effects of FailureStarting the engine is impossible in the event of signal failure.351_022Camshaft Position (CMP) Sensor G4051 Engine ManagementThrottle Position (TP) Sensor G79 and Accelerator Pedal Position Sensor 2 G185The Throttle Position (TP) Sensor G79 and Accelerator Pedal Position Sensor 2 G185 are combined in one component and integrated into the accelerator pedal module.Signal UsageThe Throttle Position (TP) Sensor G79 and Accelerator Pedal Position Sensor 2 G185 are used to detect the position of the accelerator throughout the entire adjustment range. These signals are used by the ECM to calculate the injection quantity.Accelerator Pedal ModuleEffects of FailureIn the event that one of the two sensors (G79 or G185) fail, the system switches to idle speed. If the second sensor is detected within a defined period of time, vehicle operation becomes possible again. However, the engine speed only increases slowly to the desired throttle. In the event of both sensors failing, the engine only runs at increased idle speed, and no longer responds to the accelerator.Kick Down Switch F8The Kick Down Switch F8 function is integrated into the accelerator pedal module.Throttle Position (TP) Sensor G79, Accelerator Pedal Position Sensor 2 G185, and Kick Down Switch F8Signal UsageIn addition to the accelerator position sensor signals, the Kick Down Switch F8 signal allows the ECM to detect the kick-down position. This information is transmitted to the Transmission Control Module (TCM) J217 via the drive CAN data bus, and the kick-down function is carried out.Effects of FailureIn the event of Kick Down Switch F8 failure, the ECM uses the accelerator position sensor values.351_05652 Engine ManagementBrake Light Switch F and Brake Pedal Switch F47The Brake Light Switch F and Brake Pedal Switch F47 are located together in one component on the pedal cluster. Both switches help the ECM to detect whether the brake is actuated.Brake Light Switch F and Brake Pedal Switch F47Signal UsageWhen the brake is actuated, the cruise control system is shut off, and the engine no longer responds to the accelerator pedal.Effects of FailureIf a sensor’s signal fails, the injection quantity is reduced and the engine has less output. The cruise control system is also shut off.351_025Mass Air Flow (MAF) Sensor G70The Mass Air Flow (MAF) Sensor G70 is located in the intake manifold. It works according to the hot film principle, and determines the amount of air which is actually taken in.Mass Air Flow (MAF) Sensor G70Signal UsageThe injection quantity and the exhaust gas recirculation quantity are calculated by the ECM on the basis of this signal. The signal is also used to determine the amount of diesel particulate filter contamination.Effects of FailureIn the event of signal failure, the ECM employs a substitute value comprised of the charge air pressure and engine speed for calculation purposes.351_10053 Engine ManagementEngine Coolant Temperature (ECT) Sensor G62The Engine Coolant Temperature (ECT) Sensor G62 is located on the right cylinder head’s coolant connection. The sensor provides the ECM with information on the current coolant temperature.Engine Coolant Temperature (ECT) Sensor G62Signal UsageThe coolant temperature is used by the ECM as a correction value for calculating the injection quantity, the charge air pressure, the injection point, and the exhaust gas recirculation quantity.Effects of FailureIf the sensor signal fails, the ECM uses the signal from the Engine Coolant Temperature (ECT) Sensor (on Radiator) G83 and a fixed, substitute value for calculation purposes.351_029Engine Coolant Temperature (ECT) Sensor (on Radiator) G83The Engine Coolant Temperature (ECT) Sensor (on Radiator) G83 is located in the line at the radiator outlet, where it measures the outlet temperature.RadiatorSignal UsageRadiator fan initialization is carried out by comparing the signals from the two sensors, G62 and G83.Effects of FailureIf the signal from the Engine Coolant Temperature (ECT) Sensor (on Radiator) G83 fails, radiator fan stage 1 is continuously initialized.Engine Coolant Temperature (ECT) Sensor (on Radiator) G83351_08954 Engine ManagementCharge Air Pressure Sensor G31 and Intake Air Temperature (IAT) Sensor G42The Charge Air Pressure Sensor G31 and Intake Air Temperature (IAT) Sensor G42 are integrated into one component and are located in the intake manifold.Intake Air Temperature (IAT) Sensor G42 Signal UsageThe ECM uses the sensor’s signal to calculate a correction value for the charge air pressure. Evaluation of the signal gives consideration to the influence of temperature on the density of the charge air.Charge Air Pressure Sensor G31 Signal UsageThe ECM uses the sensor’s signal to regulate the charge air pressure.Effects of Intake Air Temperature (IAT) Sensor G42 FailureIn the event of signal failure, the ECM employs a fixed, substitute value for calculation purposes. This may lead to reduced engine output.Effects of Charge Air Pressure Sensor G31 FailureThere is no substitute function in the event of signal failure. Charge air pressure regulation is shut off, leading to a significant reduction in engine outputCharge Air Pressure Sensor G31 and Intake Air Temperature (IAT) Sensor G42Charge Air Cooler, Right-HandCharge Air Cooler, Left-Hand351_03455 Engine ManagementHeated Oxygen Sensor (HO2S) G39The Heated Oxygen Sensor (HO2S) G39 is a broadband type sensor. The sensor is located upstream of the oxidizing catalytic converter in the exhaust system. It enables determination of the oxygen content in the exhaust gas over a wide measuring range.Signal UsageThe Heated Oxygen Sensor (HO2S) G39 signal is used to correct the exhaust gas recirculation quantity. The signal also serves to determine amount of contamination of the diesel particulate filter. In this calculation model, the sensor signal is used to measure the engine’s carbon emissions. If the exhaust gas oxygen content is excessively low in comparison with the nominal value, increased carbon emissions are concluded.Effects of FailureIf the signal fails, the exhaust gas recirculation quantity is determined using the Mass Air Flow (MAF) Sensor G70 signal. As this regulation is not very precise, nitrogen oxide emissions may increase. Calculation of diesel particulate filter contamination is less accurate. However