TECHNICAL DOCUMENTATION

SSP 950173 – The OBZ 7-speed Dual Clutch S tronic Transmission in the 2017 R8

PDFEN81 pages9 MB
SSP 950173 – The OBZ 7-speed Dual Clutch S tronic Transmission in the 2017 R8 - PDF cover

This PDF is currently unavailable.

Read document text
The OBZ 7-speed Dual Clutch S tronic Transmission in the 2017 R8Self Study Program 950173 Audi of America, LLC Service Training Created in the U.S.A. Created 11/2016 Course Number 950173©2016 Audi of America, LLC All rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC. Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.Revision:11/2016ii Introduction ....................................................................................... 1Overview ..................................................................................................................................................................... 2Selector mechanism............................................................................ 4Component overview ................................................................................................................................................. 5 Selector lever longitudinal lock ................................................................................................................................ 8 Selector lever transverse lock ................................................................................................................................... 9Transmission functions......................................................................12Auto-P function ........................................................................................................................................................ 12 Tip-shifting in D/S .................................................................................................................................................... 12 Activating transmission setting N (holding P-OFF setting) ................................................................................. 12 Launch control program ......................................................................................................................................... 12 Special features of the 2017 R8 ............................................................................................................................. 13 Audi drive select – transmission settings .............................................................................................................. 14Gearbox assemblies...........................................................................16Specifications ........................................................................................................................................................... 16 Overview and features ............................................................................................................................................. 16 Component overview ............................................................................................................................................... 20 Gear set/gear train configuration .......................................................................................................................... 22 Dual clutch ............................................................................................................................................................... 24 Gear train and gear set ........................................................................................................................................... 28 Gear shifting and gear-shift actuators .................................................................................................................. 30 Power transmission path in gearboxes ................................................................................................................. 32 Parking lock – mechanical function ....................................................................................................................... 36 Parking lock – electro-hydraulic function .............................................................................................................. 38 Parking lock emergency release ............................................................................................................................. 44 Oil system and ATF supply ...................................................................................................................................... 46 Oil level ..................................................................................................................................................................... 48 Lubrication and cooling of the gear train .............................................................................................................. 50 ATF temperature management .............................................................................................................................. 52Transmission control.........................................................................54Component overview ............................................................................................................................................... 54 Dual-Clutch Transmission Mechatronic ................................................................................................................. 56 Auxiliary hydraulic module ..................................................................................................................................... 62 Parking lock module ................................................................................................................................................ 63 Transmission control modules ............................................................................................................................... 65 Sensors and information ........................................................................................................................................ 66 Function diagram .................................................................................................................................................... 72 Hydraulic circuit diagram ........................................................................................................................................ 74Knowledge assessment.....................................................................76The eSelf-Study Program (eSSP) teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a repair manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. This content is not updated. For further information about maintenance and repair work, always refer to the current technical literature.NoteReferenceiii iv IntroductionThe new 0BZ S tronic 7-speed dual clutch transmission is a truly sport-oriented gear box. Shifting occurs virtually without interrupting the power transmission. The seven speeds provide a wide spread of ratios which reduce fuel consumption while retaining a close ratio configuration for better acceleration. It offers agility and easy gear shifting to meet customer expectations in terms of handling dynamics and driver convenience. To review the basic functions of a dual clutch transmission with electro-hydraulic controls, please refer to eSelf-Study Program 951403, The 02E Direct Shift Gearbox, Design and Function.643_002Learning objectives of this eSelf-Study Program: After you have completed this eSelf-Study Program, you will be able to answer the following questions: ›› What is the design of the 0BZ 7-speed dual clutch transmission? ›› How does the 0BZ 7-speed dual clutch transmission function? ›› How does the 0BZ 7-speed dual clutch transmission differ from the dual clutch transmission we are already familiar with?1 OverviewThe OBZ 7-speed dual clutch transmission is being offered for the first time in the North American market on the 2017 Audi R8. The power to the front wheels on the 2017 R8 is via the new OD4 front final drive with an electro-hydraulic multiplate clutch. For more information about this final drive, please refer to eSelf-Study Program 950163, Front Final Drive OD4 Design and Function. The drive response and handling dynamics can be varied using Audi drive select to suit the driver’s preference. See page 14.Automatic Transmission Control Module 2 J10062 0D4 front final drive with electro-hydraulically controlled multi-plate clutch eSee Self-Study Program 950163, Front Final Drive OD4 Design and Function for more information.643_012All Wheel Drive Control Module J492Selector mechanismParking lock emergency release mechanism643_0033 Selector mechanismBasic shift schematic The Audi R8 uses the latest-generation Audi B and C series selector mechanism with full "shift-by-wire" functionality. The operating concept is intuitive and is essentially identical to the familiar operating logic of other Audi automatic transmission models. The parking lock is normally engaged and disengaged by the Auto-P function but can also be engaged by the driver using the P button. See page 12. After every operation, the selector lever returns to the normal position of the automatic or tiptronic gate.tiptronic gatePossible positions of the selector lever. The following indications are displayed in the self-diagnosis sequence according to the selector lever position: X - Normal position in automatic mode T - Normal position in tiptronic mode A1, A2, B1, B2, T+, and T- are the position indicators in the selector lever position shown in each caseShift schematicAutomatic gate643_010Positions selectable without moving the selector Selectable drive positions Normal position of the selector lever and current drive position Software lock: cancelled by pressing the release button – E681 Software lock: deactivate by pressing the foot brake1) Mechanical lock by Shift Lock Solenoid N110 – cancelled by pressing Selector Lever Release Button E681643_011Note: An acknowledgement tone sounds when drive position R is engaged. Automatic gateA2 A1 Xtiptronic gateX B1 B2 T+T T-643_013Speed-dependent transmission protection function A change in driving direction from D to R and vice versa is only possible at speeds less than approximately 5 mph (8 km/h). At vehicle speeds above 5 mph (8 km/h), the transmission safety function prevents the change.643_0121) he orange-colored software lock is activated in drive position N after about one second. This allows quick-changing of the drive position from D to R and vice versa T without applying the brake. The makes it possible, to free a stuck vehicle by rocking it backwards and forwards and makes it easier to shift driving position when maneuvering.4 Component overviewHandle for selector lever top sectionSelector Lever Release Button E681 Parking Lock Button E816 – P button – Parking Lock Indicator Lamp E3320Handle for selector lever bottom section with selector leverSelector Lever Transmission Range Display Y5Selector mechanism coverPlug connection E Selector leverPlug connection C Plug connection A Selector mechanism (Selector Lever E313)643_014Selector Lever Release Button E681 Button E681 is used for releasing the selector lever lock. It consists of two shift elements for reliability and diagnostics. In the event of a fault, it is considered actuated. The locks marked red and blue (Fig. 643_011) are disabled and a DTC is recorded and then indicated on the instrument cluster. The selector can be moved out of positions P and N by pressing the foot brake.Parking Lock Button E816 The P button is for manually engaging the parking lock. The parking lock can only be activated at vehicle speeds less than 0.5 mph (1 km/h). Button E816 has three shift elements for reliability and diagnostics. Its shift status is transferred to Selector Lever Sensor System Control Module J587 via two interfaces. In the event of a fault in E816, a message appears in the instrument cluster and the parking lock can only be engaged by the Auto-P function.5 Selector Lever Sensor System Control Module J587J587 forms a functional unit with Selector Lever Position Sensor G727 and Transverse Selector Lever Lock Sensor G868. It is responsible for detecting the driver input, analyzing the button signals, communication with Gearbox Control Unit 1 J743, and all selector mechanism control and diagnosis functions. It has the Address Word 81. J587 registers the positions of the selector lever as shown in Figure 643_010 (A2, A1, X, B1, B2, T+, T and T-) and the signals from the buttons E681 and E816, and passes them on to Gearbox Control Unit 1 J743 via the Drivetrain CAN. Gearbox Control Unit 1 J743 determines the desired transmission setting and initiates the appropriate functional operations. It reports back the current transmission setting to the selector lever sensor module, and then operates Shift Lock Solenoid N110, the LEDs for Selector Lever Transmission Range Display Y5 and Parking Lock Button K320. When a transmission setting is selected, there is a brief delay before the relevant transmission setting symbol lights up.643_015Schematic diagram of selector mechanismSelector Lever Sensor System Control Module J587 Address Word 81Selector mechanismSelector lever643_016VAS 642 001 The Y adaptor VAS 642 001 allows measurements to be taken between Selector Lever E313 and Selector Lever Transmission Range Display Y5.CAN-High CAN-LowInformation If there is a system fault with the selector mechanism, the transmission ranges D and N can be selected by simultaneously pressing the two tiptronic paddles when the vehicle is stationary and the brake applied. See page 13.6 Selector Lever Position Sensor G727J587 determines all selector lever positions by means of Selector Lever Position Sensor G727. G727 consists of two sensors – one sensor for the automatic gate and one sensor for the tiptronic gate. Selector lever in automatic gateB1 B2 X A1 A2How selector lever positions are detected: The longitudinal and transverse movements of the selector lever are transmitted to a slider with two diamond-shaped sender elements. The sender elements affect the magnetic flux in the sensor elements of G727 according to the movement of the selector lever. From the sensor signals, Selector Lever Sensor System Control Module J587 generates the following selector lever positions: ›› Automatic gate A2 – A1 – X (Normal position) – B1 – B2 ›› tiptronic gate T+ – T (Normal position) – TFor more details, see the shift schematic on page 6.Slider with sender elements for automatic and tiptronic gatesCircuit board containing Selector Lever Sensor System Control Module J587, Transverse Selector Lever Lock Sensor G868 and Selector Lever Position Sensor G727.Plug connection ATransverse Selector Lever Lock Sensor G868 Selector Lever Position Sensor G727 for automatic gate Magnet for G868 Selector Lever Position Sensor G727 for tiptronic gate643_017Basic positionSelector lever in tiptronic gate Restriction of the selector lever movement to one position forwards (T+) and one position backwards (T-) is achieved by means of the tiptronic gate track of the position engagement mechanism. Key to schematic diagram of selector mechanism on page 6E313 Selector Lever E681 Selector Lever Release Button E816 Parking Lock Button G727 Selector Lever Position Sensor G868 Transverse Selector Lever Lock Sensor J587 Selector Lever Sensor System Control Module K320 Parking Lock Indicator Lamp N110 Shift Lock Solenoid V577 Transverse Selector Lever Lock Motor Y5 Selector Lever Transmission Range DisplayT TT+Movement of the base plate together with the slider and sender elements643_0187 Selector lever longitudinal lockIn transmission setting D/S, Shift Lock Solenoid N110 is energized and the locking pin engages with the selector lever lock guide. The selector can now be moved back into position B1 from the normal position in order to shift from D to S or from S to D. When Selector Lever Release Button E681 is pressed, the power supply to N110 is disconnected and the lock is disengaged. To prevent unnecessary switching noises from N110, it remains energized when switching to the tiptronic gate. The lock preventing forward movement (A1) is inactive in the tiptronic gate, however, because the lock guide is tilted to the side it becomes ineffective.Selector Lever Release Button E681Locking gateLocking pinShift Lock Solenoid N110 ›› Energized in shifter positions D and S.Cross-piece with locking grooveB2Automatic gate of position engagement mechanism ›› The position engagement mechanism has 2 gate tracks, one track for the automatic gate and one track for the tiptronic gate.B1XA1A2Basic position643_0198 Selector lever transverse lockTo ensure that the selector lever cannot be inadvertently moved into the tiptronic gate, it is transversely locked in transmission settings P, R and N. Transverse Selector Lever Lock Sensor G868Selector lever transverse lock active The selector lever is held in the cross-piece. When the transverse lock is active, the locking cam is positioned so that it engages in the locking groove of the cross-piece. When the locking cam is in that position, the selector lever cannot be moved into the tiptronic gate. Transmission setting P/R/N – selector lever transverse lock activeG868 uses Hall-effect sensors and a sensor magnet that is located at the end of the roller. The sensor magnet affects the signal of G868 according to the rotational position of the roller. From that information Selector Lever Sensor System Control Module J587 determines the position of the roller and thus the status of the selector lever transverse lock.Transverse Selector Lever Lock Motor V577Worm gearReciprocating plateRoller with swash plate, locking cam and sensor magnetTransverse Selector Lever Lock Sensor G868Magnet for G868Cross-piece with locking grooveLocking cam643_0209 Selector lever transverse lock inactiveSelector lever transverse lock cancelling functionTo be able to change to the tiptronic gate from transmission setting D or S, the selector lever transverse lock has to be deactivated.1Transverse Selector Lever Lock Motor V577 is operated by Selector Lever Sensor System Control Module J587 until the locking cam is disengaged from the locking groove of the cross-piece. The cross-piece is then no longer locked and the selector lever can be shifted into the tiptronic gate.Transmission setting D/S – selector lever transverse lock inactive21V577Transverse Selector Lever Lock Sensor G868643_0212Locking camRoller with worm gearLocking groove clear – the cross-piece and, therefore, the selector lever can move sideways in the direction of the arrow – the illustration shows the position of the selector lever in the automatic gate.643_022From the position of the magnet, the selector lever sensor module detects (with the aid of the sensor G868) that the selector lever transverse lock is not active.10 Selector lever transverse lock activeTransverse Selector Lever Lock Motor V577In transmission settings P, R and N the selector lever transverse lock is activated to prevent the selector lever unintentionally being shifted into the tiptronic gate.. To do so, Transverse Selector Lever Lock Motor V577 is operated by Selector Lever Sensor System Control Module J587 until the locking cam is engaged in the locking groove of the cross-piece. From the position of the magnet, J587 detects with the aid of G868 that the selector lever transverse lock is active.Automatic resetting of the selector lever If the selector lever is in the tiptronic gate when the ignition is switched off, it is automatically moved back into the automatic gate. J587 determines whether the selector lever is in the tiptronic gate or the automatic gate with the aid of Selector Lever Position Sensor G727.Locking cam in position ›› "transverse lock active" Locking cam in position ›› "transverse lock inactive"643_023Magnet for Transverse Selector Lever Lock Sensor G868Resetting function Starting from the position "transverse lock inactive", motor V577 rotates the roller roughly ¾ of a turn in the direction indicated by the arrow until the position "transverse lock active" is reached. During that rotational movement, the swash plate induces an axial movement (yellow arrow) on the part of the cross-piece, thereby returning the selector lever to the automatic gate.Reciprocating plateLocking cam in position ›› "transverse lock inactive"The cross-piece (and, therefore the selector lever) is pushed in the direction of the arrow by the rotation of the swash plate. At the same time, the locking cam moves into the locking groove and locks the crosspiece. Consequently, movement of the selector lever into the tiptronic gate is barred.Resetting the selector lever in emergency mode If the tiptronic function cannot be performed due to a fault, the selector lever is automatically returned to the automatic gate and locked.643_02411 Transmission functionsAuto-P functionThe parking lock is operated electro-hydraulically. See page 38. This allows Gearbox Control Module 1 to automatically operate the parking lock, thereby enhancing operating comfort. The Auto-P function engages the parking lock automatically (P-ON position) if the following conditions are satisfied: ›› Vehicle is stationary – vehicle speed less than 0.6 mph (1 km/h). ›› One of the transmission settings D, S, R or M is active. ›› The engine is switched off – Terminal 15 is off. On the 2017 Audi R8, the parking lock can also be engaged by the driver by pressing the P button, provided that the vehicle speed is less than 0.6 mph (1 km/h). The parking lock is disengaged automatically (P-OFF position) if the engine is running and one of the transmission settings D, S, R, N or M is selected.(holding P-OFF setting)Activating transmission setting NTo be able to move the vehicle without the parking lock for a limited amount of time, for example, in a car wash, automatic engagement of the parking lock can be prevented. A condition for this is that the selector mechanism, the P button and the transmission are working properly. To activate P-OFF, transmission setting N must be selected while the engine is running and then the engine switched off1). When the ignition is turned off, engagement of the parking lock is suppressed for a period of 20 minutes. After 19 minutes the following message is displayed in the instrument cluster: “Start engine to remain in N.” along with a warning tone. If this instruction is not followed, the parking lock engages after 20 minutes and the system shuts down. If a speed signal greater than 0.6 mph (1 km/h) is detected during this time, the period is extended according to the driving time of the vehicle until the system detects that the vehicle has been stationary for at least five minutes. While the vehicle is stationary with the transmission in P-OFF, power is consumed by the activity of the control modules, bus network operation and the holding solenoid. If the vehicle is stationary for an extended period of time, the battery may become discharged to the extent that the parking lock automatically engages. Therefore, if it is necessary to keep the transmission in P-OFF for an extended period, the parking lock emergency release should be actuated. More information on "Holding transmission setting P-OFF" can be found on page 37. On the 2017 R8 (100% keyless) the vehicle cannot be locked while P-OFF is active.Tip-shifting in D/SManual gear shifts can be executed at any time using the shift paddles on the steering wheel (steering wheel tiptronic controls) in transmission setting D/S. Once the steering wheel tiptronic controls have been used, the transmission remains permanently in manual mode (tiptronic mode). There are two possible ways of returning to automatic mode: ›› Pull the selector lever back one position (position B1). ›› Move the selector lever into the tiptronic gate and back into the automatic gate.Launch control programThe Launch Control Program regulates the maximum acceleration of the vehicle from a standing start. Please refer to the Owner's Manual for instructions on how to use it and follow the guidance provided. The Launch Control Program in the Audi R8 has a particularly sporty setup. In addition, forced up-shifts are performed in tiptronic mode. Refer to page 14. Notes When pulling away with Launch Control active, all vehicle components are heavily stressed. As a result, greater wear may occur. The number of Launch Control starts performed can be read in the Measuring values.12 Special features of the 2017 R8Steering wheel tiptronicThe following functions can be selected using the shift paddles on the steering wheel of the 2017 R8. ›› If both shift paddles are operated simultaneously while the engine is running, driving position N is selected (both moving and when the vehicle is stationary). ›› When the vehicle is stationary, the driver can shift from the transmission settings P, R and N to M1 by operating the Tip+ shift paddle with the brake applied. ›› Press-and-hold function: if the driver presses and holds the Tip+ shift paddle while the vehicle is moving, the transmission changes up to the highest possible gear, for example, from 3rd to 5th gear. If the driver presses and holds the Tip– shift paddle, the transmission changes down to the lowest possible gear, for example, from 7th to 3rd gear. ›› If a system malfunction occurs in the selector mechanism, the driver can select driving position D with the Tip+ shift paddle when the vehicle is stationary and with the brake pressed. N can be selected by actuating both shift paddles simultaneously. R (reverse gear) is not available. These additional functions of the tiptronic shift paddles are made possible by the use of redundant backup systems for communicating the shift commands from the shift paddles The shift commands are sent via CAN data bus to Gearbox Control Unit 1 J743 and also by two separate signal lines to Automatic Transmission Control Module 2 J1006. See also schematic diagram on page 72. The information is then, in turn, sent on by CAN data bus to J743.Tip Tip +643_02513 Audi drive select – transmission settingsThe 2017 Audi R8 is equipped with Audi drive select. That means, depending on the vehicle equipment, the driver can experience the performance capabilities and dynamic handling characteristics of different vehicle systems. In addition to the familiar Audi drive select modes – comfort, auto, dynamic and individual – the 2017 R8 has a performance mode. Within performance mode itself there are three sub-modes – snow, wet and dry. Those setups allow the handling systems to be better adapted to the road surface conditions. The Audi drive select handling system utilizes the electronic stability control (ESC) system in performance mode. Basic information about Audi drive select on the Audi R8 can be found in eSelf-Study Program 990363, The 2017 Audi R8 Introduction. It explains how the transmission control system reacts to the various Audi drive select modes.The comfort, auto and dynamic modescomfort and auto modes are identical regarding transmission setup. The shift points and the gear shifts are comfort-orientated. In dynamic mode the sport program S is selected in the gearbox. In the sport program the shift points are at higher engine speeds and shift times are reduced. This makes for better power delivery and more noticeable gear shifts. The overview on page 15 shows the effects of the various Audi drive select modes on the transmission setup.snowwetdrylast mode Performancelast mode drive selectcomfortautodynamicindividualKey: Performance button Performance button adjusting ring643_026Audi drive select button/MMI turn-and-press knob Terminal 15 changeoverPerformance mode Performance mode is standard on the V10 plus and optional on the V10. In performance mode, the transmission setup is very sporty. That means that the transmission works to maximize power delivery from the engine; comfort plays a secondary role. Gear shifts are performed at very high engine speeds, gear changes are very fast and distinctly perceptible. Performance mode can only be activated and operated using the Performance button the steering wheel. The Performance button allows the driver to activate or deactivate performance mode directly and in any Audi drive select mode.Information The following applies to vehicles for the North America region and all other countries from model year '17 on: If performance mode is selected, Gearbox Control Unit 1 switches to tiptronic mode MS+ and automatic mode is not available.Please note that the stabilization functions of the ESC and traction control systems are limited when performance mode is activated. You should only activate performance mode if you have the necessary driving skills and the traffic conditions permit. There is a danger of skidding and losing control!14 Performance button The Performance button is a touch switch with an adjusting ring. The adjusting ring is used to select the snow, wet and dry modes. Those modes have no effect on the setup of the transmission.Audi drive select buttonPerformance button with adjusting ring for selecting the snow, wet and dry modes643_027Overview of transmission setups available with Audi drive selectAudi drive select modes Transmission setups and functionsDriving position1) Shift characteristics Automatic upshifting in M mode Downshift during‑kickdown in M mode Modified accelerator map, increased idling and driveaway speed Launch control program No D normal – – dynamic = sport program M – Yes Yes S sporty – – MS – No No performance No distinction is made between dry, wet and snow MS+ – No NocomfortautoM – Yes YesD normal – –normal Nosportysuper sportyYes – with forced up-shift to M and with the most high-performance shift sequence and fastest gear changes Yes C – B No C – Yes D –Blipping the throttle during downshift Shift sequence/shift time Return to automatic mode after actuating the tiptronic shift paddles Engine start/stop mode Key to shift sequences/shift times: A B C D No A NoYes C –No A NoYesNoComfort-orientated overlapping gear shift with engine torque intervention Shift-time-orientated overlapping gear shift with maximum engine torque intervention Fast overlapping gear shift with maximum engine torque intervention – specially adapted for tiptronic operation Fastest possible overlapping gear shift with maximum engine torque intervention and utilisation of engine inertial torque during up-shifts1) he transmission setting is determined by the selector lever setting (D, S, or M) in combination with the choice of Audi drive select mode. M means: tiptronic T Manual shift program, MS means: tiptronic Manual Sport shift program , MS+ means: Manual Sport Plus shift program.15 Gearbox assembliesSpecificationsDesignations Manufacturer DL800-7A Service 7-speed dual clutch gearbox 0BZ Sales S tronic Audi AG Ingolstadt/VW plant Kassel Full synchromesh 3-shaft sliding-collar variable-speed gearbox with 7 forward gears and one reverse gear, electro-hydraulically operated for mid-engine concept, with differential lock in the rear final drive and PTO shaft for direct power transmission to the front final drive Two wet-type multi-plate clutches in an in-line configuration, electro-hydraulically operated and oil-cooled Mechatronic unit plus 2 additional electro-hydraulic modules (parking lock module and auxiliary hydraulics module) – shift-by-wire actuation with electro-hydraulically operated parking lock (park by wire), Two control module concept for park-by-wire technology and separate clutch cooling for clutches K1 and K2. Automatic mode with various shift programs and tiptronic program for manual gear-shifting. ›› 6+E configuration on the V10 (the 7th gear is a high ratio designed for fuel economy) ›› 7 speed configuration on V10 plus 311 lb (141 kg) including ATF and dual-mass flywheelDevelopment/production Gearbox typeDual clutch Control systemRatio configuration WeightOverview and features643_03816 Differential lock with modified locking characteristics for front final drive 0D4.ATF cooler1) with deflector hood (crash guard)Parking lock emergency release operated from vehicle interior by mechanical cable643_036Transmission ratios for the PTO shaft for the front final drive 0D4 ›› Basic transmission ratio on V10: 28 : 23 ›› Dynamic transmission ratio on V10 Plus: 28 : 21ATF drain and inspection plug with bayonetDual-Clutch Transmission Mechatronic J743 now participates with Immobilizer system.1)The overall cooling concept on the 2017 Audi R8 has been redesigned and substantially improved so that no additional ATF cooler (air/oil heat exchanger) is required by either engine variant.17 597 mmA CAxial alignment of input shaftXB643_037A B Electrical connection of Parking Lock Module T16a Electrical connection of Auxiliary Hydraulic Module T16bC Electrical connector T16c for Dual-Clutch Transmission Mechatronic J743 Installation space requirement from axis of transmission input shaft (= crankshaft axis) to bottom of transmissionX The 0BZ was developed specially for the new MSS platform1). That platform requires a transmission with a short installed length. Those requirements were essentially achieved by means of the following design features: ›› Compact dual clutch with directly adjacent clutches. ›› Positioning of the Mechatronic module on the side of the transmission. ›› 3-shaft gear-set configuration. ›› Positioning of the rear final drive and the PTO shaft for the front final drive.With an installed length shorter than 23.6 in (600 mm), the OBZ transmission is more than 5.9 in (150 mm) shorter than the R tronic. Together with the engine's dry-sump lubrication system, it achieves sufficient ground clearance at the same time as providing a low center of gravity for the vehicle while keeping within the baseline limit. The 0BZ 7-speed dual clutch gearbox is perfectly suited for the new MSS platform1) with mid-engine configuration and quattro drive. That platform is the basis for the 2017 Audi R8 and the Lamborghini Huracán.1)MSS = Modular Super Sports-car 18 19 Component overviewElectrical connection/circuit board for parking lock moduleParking lock mechanism and parking lock emergency release mechanismElectro-hydraulic parking lock ›› Parking lock moduleFinal drive with differential lock ›› The locking characteristics have been adapted to the quattro drive concepts ›› For more information on the differential lock refer to eSSP 950123, Audi R8 Power TransmissionDual clutch20 Parking lock gearAutomatic Transmission Control Module 2 J1006Gear set and gear actuator ›› Hydraulically operated selector platesElectrical connection of mechatronic unitElectro-hydraulic gearbox control module ›› Dual-Clutch Transmission Mechatronic J743 ›› Gearbox Control Unit 1 J743Auxiliary hydraulic module ›› ATF pump ›› Electro-hydraulic control unitElectrical connection for auxiliary hydraulic moduleElectrical connection for auxiliary hydraulic module643_03821 Gear set/gear train configurationA dual clutch transmission consists of two gear train subsets and two associated clutches - K1 and K2. Gear train subset 1 carries the uneven gears 1, 3, 5, 7 and gear train subset 2 the even gears 2, 4, 6 and reverse. In operation, only one gear train subset is transmitting power at a time, while on the other gear train subset the next gear required is pre-engaged. If, for example, the vehicle is accelerating in 3rd gear, the next gear required is 4th gear on gear train subset 2. Gear changes are performed by switching power transmission from one clutch to the other. In the above example – changing from 3rd to 4th gear – clutch K2 is engaged while clutch K1 is simultaneously disengaged. That process is referred to clutch overlap or overlap gear shifting. The entire sequence takes place in only a few hundredths of a second. The dual clutch gearbox enables quicker gear shifts which reduce power flow interruption.Rear axle final driveDifferential gear with differential lockSpur gear for driving ATF pumpK2Dual-mass flywheel for isolating rotational vibrationK1CrankshaftFront final drive input shaft ›› The final drive input shaft is also referred to as the PTO shaft.Output shaft transmission ratios ›› Basic transmission ratio on V10: 28 : 23 ›› Dynamic transmission ratio on V10 Plus: 28 : 2122 The rear final drive uses bevel gears without hypoid offset. That means that the sliding forces between the meshing teeth are smaller than with bevel gears with hypoid offset. This design enables the use of a common oil system using low-viscosity ATF for all functional transmission subassemblies. The differential has a differential lock design carried over from the R tronic. More detailed information on the differential lock can be found in eSSP 950123, Audi R8 Power Transmission. The locking characteristics have been adapted to suit the all-wheel drive concept of the 2017 R8.Pinion shaftR1 4 5Output shaft 1Input shaft 1Output shaft 26 2Input shaft 27 3Gearbox unit 1 Gearbox unit 2643_03923 Dual clutchThe dual clutch is the central functional component of the dual clutch transmission. It transmits the torque to the relevant gear train subset.Design featuresThe dual clutch consists of two wet-type multi-plate clutches, K1 and K2. The two clutches are mounted in line with each other and have the same dimensions and the same number of plates.Power transmission path in the dual clutchThe engine torque is transmitted from the dual-mass flywheel via the dog clutch to the coupling housing and from there to the clutch housing cover. The clutch cover positively interlocks with the clutch hub. The clutch hub, in turn, is connected to the inner plate carriers of the two clutches. Clutch K1 transmits the torque to its outer plate carrier, which in turn positively interlocks with input shaft 1. Clutch K2 transmits the torque to input shaft 2.Reluctor for engine speed sensorClutch housingPiston K2K2K1Piston K1 Clutch housing coverMEngineClutch hub – inner plate carrier Clutch carrierDriving deviceInput shaft 1Input shaft 2643_04024 Dual mass flywheelDriving deviceClutch coverClutch housing coverK2 K1Ring gear – for starter Clutch hub – inner plate carrierATF pump drive Clutch carrierDowel sleeveSections through fixed components – gearbox housing Power transmission path from dog clutch to clutch643_04125 Dual clutch oil systemThe oil entire oil system for the dual clutch is supplied via the clutch carrier by means of a rotational feed system. The dual clutch is mounted on the clutch carrier by two needle roller bearings. See Figure 643_041 on page 25. The clutches are supplied with the control pressure (clutch pressure), cooling oil and centrifugal oil for dynamic pressure equalization via four oil channels. Five Torlon rings form the rotary seals for the four oil channels. In order to counterbalance the effect of dynamic pressure build-up with increasing rotational speed, each of the clutches has a pressure equalization chamber (centrifugal oil chamber). The following functions are associated with the dual clutch: ›› ›› ›› ›› ›› ›› ›› ›› ›› ›› Clutch control. Dynamic pressure equalization. Start-up. Power flow reversal. Clutch cooling. Clutch control at standstill (creep control). Overload protection. Safety shut-off. Microslip control. Clutch adaptation.Basic information about those functions is provided in eSSP 951403, The O2E Direct Shift Gearbox, Design and Function.Clutch coolingEach of the two clutches has a separate and demand-based cooling and lubrication oil supply (clutch cooling system). For that purpose, the centrifugal oil temperature of each clutch is detected by a separate temperature sensor (G658/G659). The supply of oil for cooling and lubricating the clutches is provided via the centrifugal oil chambers. A special feature of the clutch cooling system on the 0BZ transmission is that the cooling oil supply for clutch K1 provided by the Mechatronic module while the cooling oil supply for clutch K2 is provided by the auxiliary hydraulic module. The clutch cooling system for clutch K2 is controlled by Clutch Cooling Valve 2 N488. Which in turn is controlled by Automatic Transmission Control Module 2 J1006.Clutch pressure, clutch K1 Dual-Clutch Transmission Mechatronic J743Clutch pressure, clutch K2Clutch cooling system for clutch K1 Gearbox Control Unit 1 J743 registers the centrifugal oil temperature of clutch K1 from Clutch Temperature Sensor 1 G658 and calculates the control current for Clutch Cooling Valve 1 N447.Clutch cooling system for clutch K2 Automatic Transmission Control Module 2 J1006 registers the centrifugal oil temperature of clutch K2 from Clutch Temperature Sensor 2 G659 and sends the information to Gearbox Control Unit 1 as a CAN message. It calculates the required control current for Clutch Cooling Valve 2 N448 and send that information to Automatic Transmission Control Module 2 J1006. J1006 then applies the specified current to N448.Clutch cooling oil/centrifugal oil, clutch K1Clutch Cooling Valve 2 for clutch K226 Clutch monitoringThe clutch pressure of the two clutches is continuously monitored by Gearbox Control Unit 1 J743. If the pressure deviates from the specified clutch pressure, the clutch concerned is de-pressurized by means of a safety cut-out. Refer to page 60. The temperature of the two clutches is continuously monitored by J743 and J1006. Two temperature sensors, G658 and G659, are used to calculate the clutch temperature and controlling clutch cooling. If a centrifugal oil temperature of around approximately 338 °F (170 °C) is exceeded, the instrument cluster displays the warning "Gearbox too hot. Please adjust driving style." and a corresponding DTC is registered in the control module.Pressure equalization chamber – centrifugal oil chamber, clutch K1Clutch piston, clutch K1 Pressure equalization chamber – centrifugal oil chamber, clutch K2Pressure chamber K1Clutch piston, clutch K2Pressure chamber K1KD2 KK1KK2 KD1Torlon ringK2 K1643_042Key:KD1 KK1 KD2Auxiliary hydraulic module Clutch cooling oil/centrifugal oil, clutch K2Clutch pressure oil channel, clutch K1Cooling oil/centrifugal oil channel, clutch K1Clutch pressure oil channel, clutch K2KK2Cooling oil/centrifugal oil channel, clutch K227 Gear train and gear setSpecial featuresThe gear set of the 0BZ transmission has the following special features: ›› Reverse gear is implemented without a separate reverse drive gear or reverse shaft. ›› The parking lock gear is combined with the sliding collar of gear set R/4 in a single unit. ›› There is a separate output shaft for driving the front wheels.Output shaft 1Sliding collar R/4 with parking lock gearInput shaft 2Input shaft 1Output shaft 2Pinion shaftDifferent output shaft transmission ratios ›› Basic transmission ratio on V10: 28 : 23 ›› Dynamic transmission ratio on V10 Plus: 28 : 21643_043Figure 643_045 opposite shows how the two output shafts 1 and 2, the pinion shaft and the PTO shaft for the front final drive are permanently engaged.Front final drive input shaft (PTO)28 DisengageThe parking lock gear is located on the sliding collar of gear set R/4. The sliding collar, the synchromesh hub and output shaft 1 are locked together rotationally. When the parking lock is engaged, output shaft 1 is locked.Reverse gearThe reversal of rotation direction for reverse gear is achieved by means of the synchronizer gear for 2nd gear. The synchronizer gears for 2nd and reverse gears are permanently engaged. In reverse gear, the torque is transmitted from input shaft 2 via the idling synchronizer gear for 2nd gear to the synchronizer gear for reverse gear. The direction of rotation of output shaft 1 is opposite to what it is in the forward gears.Reverse gearOutput shaft 1 Synchro hub Sliding collar R/4 with parking lock gear Input shaft 2Output shaft 22nd gear pinion643_044Interconnection of the shaftsOutput shaft 1Output shaft 2Pinion shaft643_04529 Gear shifting and gear-shift actuatorsGear changing is performed by means of four hydraulically operated selector forks referred to as gear-shift actuators. Each gear-shift actuator consists of a selector fork with a selector plate at each end of which is a single-action hydraulic cylinder. On the selector plate there is also a bracket holding sensor magnets and a catch. Pressure is applied to the hydraulic cylinders so that they move the selector forks to the left or right (gear engaged), depending on the gear to be selected, or to the center position (neutral position). Once the gear/neutral position is engaged, the hydraulic cylinders are de-pressurized. The gears are kept engaged by the undercut of the dog teeth and the catches on the selector plates. In neutral position, the selector plates are held in the center position by the catches. The sliding collars also have a catch for the neutral position. When the vehicle is stationary, 1st gear is always engaged on gear train subset 1. On gear train subset 2, 2nd or reverse gear may be engaged depending on the preceding driving scenario. If the vehicle is braked to a standstill after travelling forwards, 2nd gear remains engaged. Reverse gear is not engaged until transmission setting R is selected or if the engine is switched on again after being switched off and transmission setting D or R is selected. If, for example, the engine is switched off immediately after backing up, reverse gear remains engaged.Selector fork 1, gear-shift actuator A 5th/1st gearSelector plate catch Selector fork 1, gear-shift actuator A, gears 5/1Selector fork 4, gear-shift actuator D, gears R/4Gearbox unit 1 Gearbox unit 2643_04630 Gear shift monitoringFor the transmission to function perfectly, the exact positions of the selector forks must be known by transmission control module. Four travel sensors, aided by sensor magnets attached to the selector rods, define the positions of the relevant gear shift actuators/selector forks. Refer to page 68.643_047The measurements taken – actual positions of gear-shift actuator A (B/C/D) – show the gear-shift travel in millimetres. Refer to page 68.Travel of gear-shift actuatorSensor magnet for Gear Position Distance Sensor 4 G4901) for gear-shift actuator D for gears R/4 Sensor magnet for Gear Position Distance Sensor 1 G4871) for gear-shift actuator A for gears 5/13rd/4th/5th/6th gear engagedNeutral position1st/2nd/7th/Reverse gear engaged643_102In the event of malfunctions or invalid shift positions, the gear train subset concerned is hydraulically disabled by means of the safety cut-out. Refer to page 60.Selector fork 3/gear-shift actuator C, gears 3/7Sensor magnet for Gear Position Distance Sensor 3 G4891) for gear-shift actuator C for gears 3/7 Sensor magnet for Gear Position Distance Sensor 2 G4881) for gear-shift actuator B for gears 2/6 Selector fork 2/gear-shift actuator B, gears 2/6Due to manufacturing tolerances, the limit positions and synchronization points of each gear have to be learned by Dual-Clutch Transmission Mechatronic J743. This can be done via the VAS Scan Tool.1)See also page 68.31 Power transmission path in gearboxes1st gearGearbox unit 1 Gearbox unit 2Input shaft 1 Input shaft 2 Pinion shaftR1 4 5Output shaft 1K2 K1PTO shaft for front final drive22nd gear67 3Output shaft 2643_048R K2 K141 5232637643_049 3rd gearR K2 K141 524th gear637643_050R K2 K141 52637643_05133 5th gearGearbox unit 1 Gearbox unit 2Input shaft 1 Input shaft 2Pinion shaftR1 4 5Output shaft 1K2 K1PTO shaft for front final drive26th gear67 3Output shaft 2643_052R K2 K11 4 5234637643_053 7th gearR K2 K141 52Reverse gear67 3643_054R K2 K141 52637643_05535 Parking lock – mechanical functionBecause there is never any drive gear engaged when the engine is not running (both clutches K1 and K2 are not engaged), the OBZ transmission requires a parking lock. The parking lock consists of a parking lock gear and a locking pawl that is actuated by a spring loaded, tapered sliding sleeve. Unique to the OBZ transmission, is that the parking lock gear is not located on the gearbox output shaft, as is normally the case, but instead is integrated in sliding collar R/4. See page 29.Parking lock piston Parking lock spring Locking element with shoulder and holder for sensor magnetEngaging the parking lock – P-ONThe parking lock is engaged by the force of the parking lock spring. The parking lock spring forces the parking lock piston together with arrester element and tapered sliding sleeve between the bracing plate and the locking pawl. As a result, the locking pawl is pressed against the parking lock gear. The claw engages in the teeth of the parking lock gear and locks it in position.Striker block Spring-loaded tapered sliding sleeve Pawl Pivot mounted in gearbox housingResetting springParking Lock Solenoid N486Parking Lock Solenoid Valve N573 – Parking lock engagement valve Hydraulic pressure acts on parking lock piston643_078Disengaging the parking lock – P-OFFThe parking lock is disengaged by the hydraulic force of the parking lock piston. The parking lock piston pulls the tapered sliding sleeve back against the force of the parking lock spring. The return spring forces the locking pawl out of engagement with the gear teeth and holds it in that position.643_07936 Engaging the parking lock if pawl and gear do not mesh1. If the claw of the locking pawl clashes with a tooth of the parking lock gear, the tapered sliding sleeve is still forced between the bracing plate and the locking pawl by the preloaded spring force. The tapered sleeve is spring-loaded and presses the locking pawl against the tooth of the parking lock gear.2nd step1st stepTapered sliding sleeve – springloadedClaw and tooth clashing643_0802. As soon as the vehicle rolls a little and the parking lock gear rotates slightly, the locking pawl snaps into engagement with the parking lock gear because the tapered sleeve is preloaded by the force of the spring. The parking lock is engaged.643_081Holding the parking lock in position P-OFF with Parking Lock Solenoid N486A - Keeping parking lock disengaged If the parking lock needs to remain disengaged after the engine is switched off, the parking lock piston has to be held in the P-OFF position by the Parking Lock Solenoid N486. To hold the lock in position P-OFF, N486 remains energized after the engine is switched off. That means that the armature of N486 remains pulled in against the force of the spring (Figure A). In that position, the 3 ratchet springs of N486 engage with the locking tip of the arrester element and so lock the parking lock piston in the P-OFF position. More information on activating the transmission setting P-OFF can be found on page 12.Ratchet springArrester element with parking lock pistonABSnap hookPiston springPistonsLocking elementB - Engaging the parking lockN4 86If N486 is de-energized, the armature of N486 moves out (to the right) under the force of the armature spring. As a result, the ratchet springs are forced apart and release the arrester element of the parking lock piston. The parking lock piston is thus unlocked and the parking lock spring forces the parking lock piston into the P-ON position.643_08237 Parking lock – electro-hydraulic functionNormal position – Parking lock ON – Engine OFFThe following circuit diagram shows the system in pressurized and depressurized condition. The spring in the parking lock piston ensures that the parking lock is engaged. A hydraulic circuit with spring-loaded self-holding valve (SHV) and an additional holding solenoid (N486) for the P-OFF position make sure that the parking lock cannot be unintentionally engaged when the vehicle is moving. WhenParking Lock Solenoid Valve 2 N574 and Parking Lock Solenoid N486 are de-energized, the parking lock always remains engaged. In that circuit setting, the pressure line of the parking lock piston has an open connection to the sump via the self-holding valve (SHV) and is not pressurized. The basic principle is: When it has no oil pressure and power supply, the parking lock is always engaged (parking lock PN). Solenoid valve N574 is only briefly operated. The self-holding valve retains whichever switching condition is initiated.Parking lock gearParking lock pistonParking lock moduleAuxiliary hydraulic moduleKey:N486 Parking Lock Solenoid – PHM – Parking lock holding solenoid N573 Parking Lock Solenoid Valve – PEV – Parking lock engagement valve N574 Parking Lock Solenoid Valve 2 – PAV – Parking lock disengagement valve SHV Self-holding valve A1 A2 A3 SHV piston face A1 SHV piston face A2 SHV piston face A3Primary pressure supply643_08338 Parking lock ON – engine runningEven if the primary pressure is present when the engine is running, the self-holding valve remains in its normal position and keeps connection between the parking lock piston pressure line and the sump open and, therefore, depressurized. When P-ON is active, N573 remains energized until the engine is switched off. That means the connection between the parking lock piston and the sump is open. This prevents unintentional pressure build up that would result from the disengagement of the parking lock. The self-holding valve, SHV The SHV has a spring-loaded valve with 3 different-sized piston faces – faces A1, A2 and A3. Depending on the switching position of the solenoid valves N573 and N574, either the primary pressure (equal pressure) or no pressure is acting on those faces. Since the same pressure acts on all the piston faces, different forces result and enable the valve to be moved to the desired setting. The following relationships apply to the piston faces:1. Face A2 is smaller than face A1. 2. Faces A2 and A3 combined are larger than face A1.A larger face (A) = Greater force In the situation illustrated in Figure 643_084 – primary pressure applied to A2 and A1 – the SHV remains in the lefthand position because the force acting on piston face A1 is greater than that on A2.Parking lock moduleAuxiliary hydraulic modulePrimary pressure supply643_08439 Disengaging the parking lock and holding the P-OFF settingTo disengage the parking lock, primary pressure is applied to the packing lock piston. The hydraulic force is many times greater than the force of the parking lock spring, so the parking lock piston is forced back together with the tapered sleeve. The return spring of the locking pawl lifts the pawl out of engagement with the parking lock gear and so releases the parking lock. See Figure 643_079 on page 36.Parking lock moduleElectro-hydraulic functionStep 1Auxiliary hydraulic moduleParking Lock Solenoid Valve N573 has to be de-energized. By operating Parking Lock Solenoid Valve 2 N574 the control line for piston A1 is connected to the sump and de-pressurized. Initially, pressure is only applied to piston face A2, causing the self-holding valve, SHV, to switch over to the right. At that point, the primary pressure is connected through to the parking lock piston via N573 and the parking lock is disengaged. At the same time, the primary pressure is directed to piston A3 via a control line. The primary pressure is then acting on both piston faces A2 and A3. At the same time as the valves N573 (OFF) and N574 (ON) are switched over, Parking Lock Solenoid N486 is also energized.Primary pressure supplyParking lock gearParking lock piston643_085Parking lock springStep 2 As soon as the position P-OFF is definitely detected (signal from G747 plus short delay), N574 is de-energized. N574 is then back in its normal position and applies primary pressure to piston face A1. The switching condition of the SHV remains unchanged, however, because the forces acting on A2 and A3 are greater than the force on A1 (self-holding function). Primary pressure is acting on the parking lock piston and holds the parking lock in the position P-OFF. The energized Parking Lock Solenoid N486 acts as an additional safeguard against unwanted engagement of the parking lock while the vehicle is being driven. If, for example, the ATF supply were to fail (for example, because of the engine stopping) while the vehicle is moving, the parking lock would be engaged. In such a scenario, Parking Lock Solenoid N486 prevents the parking lock engaging and so protects the parking lock (and the transmission) from damage. Refer to Figure 643_089.Parking lock moduleAuxiliary hydraulic modulePrimary pressure supply40643_086 Holding the position P-OFF in transmission setting N.To prevent the parking lock being engaged when the engine is switched off, transmission setting N must be selected while the engine is running. If the engine is switched off with the transmission in N, N486 remains energized. The Parking Lock Solenoid N486 then keeps the parking lock piston in the P-OFF position. More information on the subject can be found on page 12 and page 37. Key:N486 Parking Lock Solenoid – PHM – Parking lock holding solenoid N573 Parking Lock Solenoid Valve – PEV – Parking lock engagement valve N574 Parking Lock Solenoid Valve 2 – PAV – Parking lock disengagement valve SHV Self-holding valve A1 A2 A3 SHV piston face A1 SHV piston face A2 SHV piston face A3643_089Engaging the parking lock – parking lock ONParking lock spring643_087643_088643_084Step 1 To engage the parking lock, N486 must first be switched off.Step 2 At the same time, N573 is energized. That connects the pressure line for the parking lock piston and the control line for piston A3 to the sump, thereby de-pressurizing them. The parking lock is engaged by the force of the parking lock spring.Step 3 As primary pressure is acting on piston face A3, the self-holding valve, SHV, switches over to the left into its normal position. The entire pressure line for the parking lock piston is then connected through to the sump and thus de-pressurized. N573 is not switched off until the engine is switched off. Refer to page 38.41 In normal operation, the parking lock is electro-hydraulically actuated. To enable electro-hydraulic disengagement of the parking lock, the engine must be running to generate sufficient ATF pressure. And to hold the parking lock in the OFF position, there must also be sufficient ATF pressure or an adequate power supply to Parking Lock Solenoid N486. The emergency release mechanism serves to disengage the parking lock and hold it in the P-OFF position if the electrohydraulic function fails or if it is necessary to hold the P-OFF position for an extended period.The emergency release mechanism of the parking lock must be actuated in the following situations: ›› In general, when recovering or maneuvering the vehicle. ›› If the parking lock cannot be released electro-hydraulically due to a malfunction. ›› If the vehicle cannot be maneuvered or moved due to insufficient onboard voltage. ›› If the engine is not running and it is necessary to maneuver or move the vehicle, for example, in the workshop. ›› For function testing after carrying out assembly work on components of the emergency release mechanism. See Note.After removing and installing the transmission or carrying out assembly work on components of the emergency release mechanism, a function test must be performed as described in the workshop manual.42 43 Parking lock emergency releaseThe parking lock is emergency-released from inside the vehicle by means of a cable pull. The special socket tool and the screwdriver are included in the vehicle tool kit.Operating the parking lock emergency release (position P-OFF)Follow the instructions on the page opposite.Warning! Before actuating the emergency release device of the parking lock, the vehicle must be secured to prevent it from rolling away.Indications on the instrument clusterWhen the parking lock emergency release device is actuated, the yellow gearbox warning lamp and the gear drive position indicator N light up in the instrument cluster. In addition, information on the instrument cluster indicates that the parking lock cannot be engaged, there is a risk of the vehicle rolling away, and the parking brake should be applied.643_029Deactivating the emergency release (P-ON position)The emergency release mechanism is deactivated in reverse order.643_03044 OperationInlay in cupholder1. Remove inlay from cupholder. 2. Remove the cover with a screwdriver. Remove the screw, push the release tab (arrow) and take out the cover.CoverSocket wrench3. Fold the socket wrench as shown and insert it into the actuating mechanism. 643_031 4. Fold the special socket tool as shown and move it into position.Direction of travel643_032643_03345 Oil system and ATF supplyThe 0BZ transmission has a common ATF oil system for all functional sub-assemblies and oil chambers of the gearbox. The Mechatronic module has its own oil chamber in which its own oil level is established. See page 48. The following functional sub-assemblies are supplied and/or controlled, lubricated and cooled with ATF. ›› ›› ›› ›› ›› ›› Mechatronic module. Dual clutch. Hydraulic selector mechanism. Hydraulically operated parking lock. Gear set (gear train). Final drive with differential lock. The special ATF and the ATF pressure filter currently have a service/replacement interval of approximately 40,000 miles (60,000 km) (the ATF intake filter is not replaced). In order to be able to drain off the used oil as completely as possible, the 0BZ gearbox has several ATF drain plugs. Note: when changing the ATF, all drain plugs always have to be removed.ATF filter ›› with heat shield (partial-flow pressure filter) Make sure the heat shield is always installed. Otherwise, there is a risk of damage to the transmission.ATF drain plug for Mechatronic module oil chamberThere may also be a drain plug here, depending on version.ATF intake filter – integrated in ATF sumpATF drain plugs643_056Note on draining the ATFThere are different versions of the ATF drain plugs and the overflow pipe. Follow the instructions given in the workshop manual, ETKA and on the VAS Scan Tool when checking and changing the ATF.Overflow pipeATF inspection and drain plug643_05746 ATF pumpOne of the most important components of an automatic transmission is the ATF pump. The 0BZ transmission is supplied with oil by an ATF pump that is constantly driven by the engine (internal gear pump). The ATF pump is driven by a spur gear system of which the drive gear is attached to the clutch housing. See page 22, Figure 643_039.Oil pipe to clutch cooling circuit for clutch K2The ATF pump is part of the auxiliary hydraulic module. See page 54.Oil pipe connections to parking lock moduleOil pipe connections to and from Mechatronic moduleBracket/ securing clip643_058ATF filtrationThe ATF is filtered by an intake filter integrated in the ATF sump and a partial-flow pressure filter through which the return flow from the ATF cooler passes. Part of the cooled and filtered ATF is diverted by the Mechatronic module used directly to control the clutch cooling circuit for clutch K2.Intake connection – connected directly to ATF intake filterPipe to clutch cooling circuit Clutch K2ATF filter Partial-flow pressure filter643_05947 Oil levelOn the 0BZ gearbox, the Mechatronic module is in its own oil chamber, which is formed by a partition dividing it off from the gear train. In operation, that oil chamber (Mechatronic module oil chamber) fills with ATF until it is largely or completely (depending on gearbox version) immersed in ATF. That ensures that the hydraulic system is well vented and the Mechatronic module always operates under the same physical conditions. In addition, the solenoid valve coils are effectively cooled. The Mechatronic module oil chamber fills up with exhaust oil from normal operation of the solenoid valves and is thus continually filled. An overflow facility provides for venting and a defined oil level in the Mechatronic module oil chamber. Version A - transmission codes NXZ and PTX There are two transmission version