TECHNICAL DOCUMENTATION
SSP 960243 – The 2015 A3 Cabriolet

This PDF is currently unavailable.
Read document text
eSelf Study Program 960243The 2015 A3 Cabriolet2Audi of America, LLC Service Training Created in the U.S.A. Created 06/2014 Course Number 960243 ©2014 Audi of America, LLC All rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC. Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.Revision 1: 5/28/20143ContentsIntroduction.......................................................................................7 Body...................................................................................................9Structure/materials ................................................................................................................................................. 9Convertible top................................................................................ 13Movable convertible top well ................................................................................................................................ 15 Convertible top box lid/service position .............................................................................................................. 16 Convertible top frame ........................................................................................................................................... 17 Hydraulic unit ......................................................................................................................................................... 18Convertible top control system....................................................... 19Component locations ............................................................................................................................................ 19 Convertible top operation ..................................................................................................................................... 21 Components of the convertible top control system ........................................................................................... 33 Emergency operation ............................................................................................................................................ 45 Data bus overview .................................................................................................................................................. 48Occupant protection........................................................................ 49Side airbag .............................................................................................................................................................. 51 Electrical wiring harness for side airbag ............................................................................................................. 52 Driver Side Rear Side Airbag Crash Sensor G256 ................................................................................................ 52 Rollover protection ................................................................................................................................................ 53 Cassettes with protective roll bars ...................................................................................................................... 54 Driver Side Rollover Protection Igniter N646 and Front Passenger Side Rollover Protection Igniter N647 .................................................................................... 54 Resetting a deployed protective roll bar .............................................................................................................. 56 Diagnostics ............................................................................................................................................................. 56Engines............................................................................................ 571.8L and 2.0L TFSI engines ................................................................................................................................... 57Engine/transmission combinations................................................. 59 Suspension...................................................................................... 61Overall concept ..................................................................................................................................................... 61 Overview ................................................................................................................................................................. 62Electrical system............................................................................. 63Installation locations of control modules ........................................................................................................... 63 Topology ................................................................................................................................................................. 65Climatronic...................................................................................... 67Operation ................................................................................................................................................................ 68Infotainment................................................................................... 71Overview of versions .............................................................................................................................................. 71 Antenna system ..................................................................................................................................................... 75Service............................................................................................. 77Service interval overview for North American region ......................................................................................... 77Self Study Program......................................................................... 78 Knowledge Assessment.................................................................. 804This eSSP contains video links which you can use to access interactive media.Note This eSelf Study Program teaches a basic knowledge of the design and functions of new models, new automotive components or technologies. It is not a Repair Manual! All values given are intended as a guideline only. For maintenance and repair work, always refer to the current technical literature.Reference5Audi A3 Cabriolet ’15Sporty, elegant and multi-faceted - the new 2015 Audi A3 Cabriolet. This compact four seater impresses at first glance with its flowing lines and and soft top. It is also at the top of its class technically with systematic lightweight design, new engines, sophisticated networking and high performance driver assistance systems. The A3 Cabriolet has a soft top that is stretched over a lightweight magnesium and steel kinematic mechanism. At the press of a button,the top opens or closes electrohydraulically in less than 18 seconds; even when driving up to speeds of 31 mph (50 km/h). The fully automatic top has a glass rear window with an electric rear defroster. An active rollover protection system protects the occupants in case of a rollover accident. As with every Audi, workmanship quality is uncompromisingly high, and the vehicle’s controls are simple, intuitive and convenient. The A3 Cabriolet offers enough room for four adults. The rear seats can be folded down to create a wide through-load area when the top is up. The interior features new steering wheel and seat designs as well as an electromechanical parking brake operated by a push button on the center console. All engines in the new A3 Cabriolet combine the high technologies of direct fuel injection and turbocharging. On average, the two engines offered at market launch have excellent fuel economy while offering a high performance driving experience (1.8 and 2.0L). The chassis of the A3 Cabriolet uses sophisticated technology that delivers sporty handling, superior vehicle safety and a high level of comfort. Some components of the MacPherson strut front suspension are made of aluminum while the four-link rear suspension handles longitudinal and transverse forces separately. The power steering system features an efficient electro-mechanical drive. The ABS/ESP system has all the features offered on other Audi vehicles which provide safe, stable and predictable operation.623_0016IntroductionDimensions55.4 in (1409 mm)37.2 in (1526 mm)61.2 in (1555 mm) 70.5 in (1793 mm)60.07 in (1526 mm) 77.1 in (1960 mm)623_002m)00 min (1039.336.2 (921mm )34.21 in (869 mm)102.16 in (2595 mm) 174.05 in (4421 mm)37.67 in (957 mm)726.9 in (685 mm)623_00357.7 in (1468 mm)254.8 in (1392 mm)147.3 in (1203 mm)245.7 in (1162 mm)139.3 in (1000 mm)38.7 in (984 mm)623_004Length Width Height Track width, front Track width, rear Wheelbase Trailer load with brake at a gradient of 8 % Curb weight Max. gross weight174.05 in (4421 mm) 70.5 in (1793 mm) 55.4 in (1409 mm)3) 61.2 in (1555 mm) 60.07 in (1526 mm) 102.1 in (2595 mm) 3968.3 lb (1800 kg) 3152.6 lb (1403 kg) 4254.9 lb (1930 kg)Cabin width, front1) Cabin width, rear Headroom, front2) Headroom, rear Load sill height Trunk capacity Fuel tank capacity Drag coefficient in cw57.7 in (1468 mm) 47.3 in (1203 mm) 39.3 in (1000 mm) 36.2 in (921 mm) 26.9 in (685.0 mm) 11.3 cu ft (320 l) 13.2 gal (50.0 l) 0.30Shoulder room width Maximum headroom 3) excluding mirror1) 2)8BodyStructure/materialsThe body of the 2015 A3 Cabriolet is based on the 2015 A3 sedan. Thanks to Audi ultra-lightweight technology, convertible specific elements such as the ‘A’ pillar, front roof frame, rear bulkhead and the underbody are designed so they do not add undesirable weight to the vehicle.Lightweight steel componentsThe front fenders, doors, convertible top box lid, trunk lid and rear bumper cross member are made from lightweight steel. The front bumper cross member and hood are made from aluminum.9Key:623_106Ultra-high strength hot-formed steel Advanced high strength steel High strength steel Low strength steel Sheet aluminium Aluminium section10A-pillar reinforcementThe 2015 A3 cabriolet affords a high level of safety in the event of a rollover accident through its extremely stiff two-component A-pillar structure. The A-pillar is constructed with a modern high tensile strength inner plate and a ultra-high strength hot-formed steel reinforcement tube.Reinforcing tubeInner A pillar623_107Side member, sill, and seat cross member reinforcementsVarious additional reinforcements are used to ensure the body structure meets the high convertible specific strength requirements in the side member, sill, seat cross member and B-pillar areas. To provide better side impact protection, the seat cross member located between the B-pillars is made from ultra-high strength hot-formed steel.Seat cross-memberB-pillar with reinforcementsReinforcement Side member/sill623_10811Rear bulkheadAdditional body strengthening is provided by the rear bulkhead. High strength sheet steel is used to provide extremely high rigidity in crash relevant areas like the rollover protection system mounting points. This not only provides optimum safety for the vehicle occupants, it also increases the stiffness of the occupant cell significantly.Rollover protection system mountingRear bulkhead623_109Door side impact reinforcementSide impact protection623_110Additional reinforcements12Convertible topThe Audi A3 Cabriolet roof is a classical soft top design known as a K fold system. The frame is made of magnesium, aluminum and steel components. It opens electro-hydraulically in less than 18 seconds even while driving at speeds up to 31 mph (50 km/h). When the top is opened it folds into three layers and is stored in its own well. The soft top is made from rugged materials and has an integral heated glass rear window. This makes the A3 Cabriolet suitable even for winter use. The complete convertible top (frame and cover) weighs approximately 112 lb (51 kg).Roof bowRoof bowWelting stitched into the convertible top cover slides into grooves in the roof bows. The cover can be removed and installed by pulling or pushing it from the sides, simplifing repairs. The interior headliner clips to the underside of the roof bows.Convertible top cover with sound insulating foamConvertible top cover welting Headliner retaining stripRoof bowHeadliner623_11113Convertible top fabricThe convertible top cover itself is a three-layered structure. The outer layer is made of an acrylic nitrile fabric, the middle layer of butyl rubber while the inner layer is a polyester fabric. The cover is a three part design; it has a middle panel and two side sections.Convertible top cover Sound insulating foamInterior lining623_112Rear window The glass rear window is made of 3.15 mm toughened safety glass and is electrically heated. It is bonded to the convertible top cover. AM antenna (AM2, R11) AM2 is sewn into the convertible top material.Tensioning strut The tensioning strut sits on the convertible top box lid when the top is closed and locked into position. This allows the hydraulic system to be depressurized after closing.623_113!Note The integrated glass rear window cannot be replaced separately from the convertible top cover.14Movable convertible top wellA movable convertible top well is located in the luggage compartment of the A3 Cabriolet. The top can only be lowered when the movable convertible top well is in its lowest position. It is lowered manually by using a pull handle. When the convertible top is closed, the movable convertible top well can be raised to provide more room in the luggage compartment.WindbreakThe windbreak reduces drafts inside the vehicle for greater comfort when driving with the top down. It attaches to the rear side trim panels behind the front seats and is then moved into an upright position. The windbreak can remain installed in the vehicle when the convertible top is closed or it can be stored in its own bag in the luggage compartment when removed.15Convertible top box lid/service positionThe convertible top box lid is a lightweight steel component that protects the top when it is down. The lid is opened and closed by two hydraulic cylinders mounted on the left and right hinges. During repair work on the convertible top, both the top and the convertible top box lid must be moved into a service position. To prevent the top from closing, both knee hinges must be pushed towards the tensioning strut at the upper pivot point as far as the stop. A tensioning strap (T10038) and two hooks (T40306) are then attached to the top centrally at the front and rear edges and hold the top in its assembly position.T 10038 T 40306 T 40306 Convertible top box lidKnee hinge623_114Movable convertible top well top well, upper positionConvertible top, lower position623_11516Convertible top frameThe convertible top frame is bolted to the car body on both the left and right side with a main bearing attached to a mounting plate. The position of the plate is defined by the reference point system (RFS) of the car body during manufacturing and cannot be changed.Roof bow tensioning strap Front roof bow Convertible top locking motor Convertible top lock Roof bow 4 Roof bow 1 Roof bow 2 Roof bow 3Roof bows 1 - 4 are made from extruded aluminum sections. Because of its complex design, the front roof bow is made from high grade magnesium. The use of these materials enables the top frame to meet high standards for stability and strength.Front roof rodHydraulic cylinder for tensioning strut AM antennas Tensioning strut Rear roof rodMain side bar Hydraulic cylinder Convertible top box lid Rear windowHydraulic cylinder for tensioning strutMain bearing with hydraulic cylinder for convertible topHydraulic unit Hydraulic cylinder Convertible top box lid623_116Main bearing service toolsTwo spacers (special tool T40307) are inserted into the left and right main bearings from above when the top is removed. They remain installed in the main bearings during the time the top is removed and stored during repairs. When the top is removed, the spacers replace the missing stop buffers on the car body and prevent damage to the top cover and frame.T40307!17Note Please follow the instructions given in the Electronics Service Information during all work on the convertible top.Hydraulic unitAn electric motor, valve block (including pump and valves) and an oil tank make up the hydraulic unit. Plastic sheathed flexible metal spiral hoses connect the hydraulic cylinders to the hydraulic unit. Relays J588 and J321 are clipped onto the hydraulic unit and control the operating current for the clockwise and counter-clockwise operation of the pump. When the top is being raised or lowered, the pump runs and valves 1 - 3 control the flow of fluid according to the required sequence of movements. The pump rotation only needs to be reversed to move the tensioning strut into position when raising the top. Pump pressure is limited to 2611 psi (180 bar) by pressure limiting valves. When the system is at rest, the hydraulic fluid can flow back from the hydraulic cylinders to the fluid reservoir unpressurized. This operating feature also allows the emergency operation of the top.Plastic-sheathed flexible metal spiral hose Valve blockElectric motorPower Convertible Top Valve 2 N341 Power Convertible Top Valve 1 N272 Power Convertible Top Valve 3 N342 Oil filler boltOil reservoirConvertible Top Hydraulic Pump Relay 2623_118Convertible Top Hydraulic Pump Relay J321Bleeding the systemNo bleeding process needs to be done after repairs to the hydraulic system. The system is bled automatically during operation.Hydraulic cylinderBi-directional hydraulic cylinders are used. They are activated according to the convertible top movement sequence.Solenoid valvesThe hydraulic system uses 3/2 way valves (3 connections and 2 switch positions) which are operated by solenoids. Oil flows from the hydraulic cylinders and into the oil reservoir when the valves are de-energized and from the pump to the cylinders when energized. The valves are activated by Convertible Top Control Module J256 for up to five minutes. The top can be emergency operated immediately after the valves have been switched off. When the valves are de-energized after five minutes, the hydraulic system depressurizes.18Convertible top control systemComponent locationsF412 F294 F295 V223F411J285E13719KeyE137 F171 F202 F293 F294 F295 F404 F407 F408 F411 F412 F517 F519 F520 Power Top Operation Switch Convertible Top Open Position Switch Convertible Top Front Closed Position Switch Convertible Top Compartment Latch -Unlocked- Switch Convertible Top Latch -Open- Switch Convertible Top Latch -Closed- Switch Convertible Top Compartment -Locked- Switch Convertible Top Compartment -Open- Switch Upper Tensioning Bow Switch Left Convertible Top Closed Position Switch Right Convertible Top Closed Position Switch Lower Bracket Switch Convertible Top Compartment Cover -Closed- Switch Lower Convertible Top Compartment Enclosure Switch J256 J285 J321 J588 N272 N341 N342 V118 V222 V223 Convertible Top Control Module Instrument Cluster Control Module (diagram showing convertible top status) Convertible Top Hydraulic Pump Relay Convertible Top Hydraulic Pump Relay 2 Power Convertible Top Valve 1 Power Convertible Top Valve 2 Power Convertible Top Valve 3 Convertible Top Hydraulic Pump Convertible Top Compartment Cover Locking Motor Convertible Top Locking MotorF520 F519 F404 F293 V222J256 N341 N272 N342F171 F202 F517 F408 F407J588V118623_023J32120Convertible top operationPower Top Operation Switch E137The convertible top opening cycle is started by pulling Power Top Operation Switch E137. To open the convertible top completely, the switch must remain pulled until the opening cycle is complete. When the switch is released, the convertible top cycle stops instantaneously. If the switch is pulled again, the convertible top continues to open. If the switch is pressed, the convertible top closes. The switch must also be remain pressed during the closing cycle. If the convertible top is closed and the switch is pulled and then released again, the side windows will lower to a defined level. The convertible top cycle will not start. If the button is kept pressed for 5 seconds, the side windows close again.623_024Power Top Operation Switch E137Graphic displays for convertible top operationThe operation of the convertible top is indicated graphically in the Driver Information System (DIS) of Instrument Cluster Control Module J285. As soon as the top starts to open or close, the graphic display appears in the DIS. The display will either be in color or monochrome depending on the Instrument Cluster version.A curved arrow over the convertible top indicates the direction of the convertible top. If the arrow tip is pointing back, the convertible top is opening. If the arrow tip is pointing forward, the convertible top is closing.Convertible top opening cycle623_025Convertible top opening cycle623_02621If no arrow is displayed over the convertible top, the convertible top cycle has been initiated but aborted. The convertible top is in an intermediate position.Convertible top cycle aborted, intermediate position623_027Convertible top cycle aborted, intermediate position623_028If the convertible top cycle has been completed, the status of the convertible top (opened or closed) is indicated for approximately 2 seconds. An audible signal sounds at the same time.Convertible top cycle completed, convertible top closed623_029Convertible top cycle completed, convertible top closed623_030Convertible top cycle completed, convertible top open623_051Convertible top cycle completed, convertible top open623_05222If convertible top operation is not possible, an audible warning is sounded by the Instrument Cluster and one of nine visual warnings is given in the DIS.The warning is given if: • The convertible top is in the intermediate position. • There is a DTC in the fault memory. • The vehicle is traveling faster than 3.1 mph (5 km/h).Warnings are indicated via the color DIS as follows:Triangle with exclamation mark in the driver information and warning lamps tab Yellow vehicle-with-convertible-top icon in the status lineConvertible top: malfunction!Displayed textyou can continue driving (limited functionality). See owner's manualYellow central warning lamp623_031Warnings are indicated via the monochrome DIS as follows:Exclamation mark in driver information tab and warning lamps tab Vehicle convertible top icon in the status lineConvertible top: malfunction!Displayed textyou can continue driving (limited functionality). See owner's manualYellow central warning lamp623_03223Other reasons why a convertible top operation is not possible are displayed as messages.Display of the 9 functional or visual messages in the DIS:• • The yellow warning lamp is NOT activated when the functional or visual messages messages are displayed. Messages are indicated by a white vehicle-with-convertible-top icon in the status line in both the color and monochromeDriver Information System displays. Message texts are NOT included in the driver information and warning lamps tab.• If the convertible top is in a limit position (open or closed) and a convertible top cycle is initiated in the limit stop direction, no actions are initiated and no messages are displayed. To activate messages, the following conditions must be met: The trunk lid is open and the convertible top operating switch is actuated.Convertible top: Please close boot lid623_033The convertible top well is in the upper position and the convertible top operating switch is actuated in the "open" direction. Convertible top: Please lower convertible top well623_034The convertible top is in a limit position (open or closed), the vehicle is travelling faster than 31 mph (50 km/h) and the convertible top operating switch is actuated. Convertible top: no operation possible. Speed too high623_03524A convertible top cycle is currently active and the vehicle's speed increases to over 31 mph (50 km/h). or the convertible top is in an intermediate position and the vehicle speed exceeds 31 mph (50 km/h). Convertible top: not in limit position. Speed too high623_036The ambient temperature is below 5 °F (-15 °C), the convertible top is closed and the the operating switch is actuated in the “open” direction. An open convertible top can be closed at temperatures below 5 °F (-15 °F). Convertible top: no operation possible. Ambient temperature too low623_037Convertible Top Control Module J256 has registered a DTC and the switch is actuated.Convertible top: no operation possible623_03825The vehicle battery voltage has dropped below a threshold value; the ignition is switched ON, the engine is not running, and the convertible top operating switch is actuated.Convertible top: no operation possible. Engine must be running623_039The overload protection is active and the convertible top operating switch is actuated.Convertible top: no operation possible623_040Convertible Top Control Module J256 has registered a DTC, the limit position (open or closed) has been reached and the convertible top operating switch is released.Convertible top: malfunction! You can continue driving623_04126Convertible top opening sequenceTo open the convertible top, the following conditions must be met: • The vehicle must not be travelling faster than 31 mph (50 km/h) • The power top operation switch E137 must be pulled and held • The ambient temperature must be above 5 °F (-15 °C) • • • • The convertible top well must be in the lower position The trunk lid must be closed The vehicle battery voltage must be sufficient Both front and rear side windows must have pinch protection activatedInitial situation: the convertible top is closed Assuming the previous conditions are met and Power Top Operation Switch E137 remains pulled up, all the side windows will lower to a defined position.623_043623_042Convertible Top Operation Switch E137A vehicle image appears in the Driver Information System display showing the vehicle with a convertible top and a curved arrow. The arrow tip is pointing back.Convertible top opening cycle623_044Convertible top opening cycle623_045The Release Button in Rear Lid Handle E234 is deactivated so the trunk lid cannot be opened.If the rear window defroster is ON, it is switched OFF. The rear window defroster can only be switched ON when the convertible top is fully closed.27The catch hooks in the upper part of the lock in the windshield frame area are opened. The tensioning strut begins to move into the upright position.623_046At the same time, Convertible Top Compartment Cover Locking Motor V222 opens the convertible top box lid. The tensioning strut moves into the upright position. The convertible top box lid opens fully.623_047The convertible top retracts and folds down into the convertible top well. Meanwhile, the catch hooks close again.623_048After that, the convertible top box lid closes and V222 locks it into position.An acoustic signal and graphic display indicate that the convertible top cycle is complete and the convertible top is fully open.623_049Convertible top cycle completed, convertible top open623_051Convertible top cycle completed, convertible top open623_052Finally, the side windows raise to their closed position and the Release Button in Rear Lid Handle E234 is re-activated so the trunk lid can be opened.623_05028Convertible top closing sequenceTo be able to close the convertible top, the following conditions must be met: • • • • The vehicle must not be travelling faster than 31 mph (50 km/h) The function must be activated The trunk lid must be closed The vehicle battery voltage must be sufficientInitial situation: the convertible top is open Assuming the previous conditions are met and Power Top Operation Switch E137 remains pressed, all the side windows will lower to a defined position.623_046a623_042Power Top Operation Switch E137A vehicle image appears in the Driver Information System display showing the vehicle with a convertible top and a curved arrow. The arrow tip is pointing forward.Convertible top closing cycle623_053Convertible top closing cycle623_054The Release Button in Rear Lid Handle E234 is deactivated so the trunk lid cannot be opened.29Convertible Top Compartment Cover Locking Motor V222 unlocks the convertible top box lid. The convertible top box lid opens fully.623_046bThe convertible top lifts up out of the convertible top box and the catch hooks in the upper part of the convertible top lock open.623_046cThe tensioning strut moves into the upper position and the convertible top box lid closes fully. V222 locks the convertible top box lid.623_046dThe convertible top continues to run until it settles on top of the windshield frame. At the same time, the tensioning strut moves down. The catch hooks then lock the convertible top in place.623_046eAn acoustic signal and graphic display indicate that the convertible top cycle is complete and the convertible top is fully closed.Convertible top cycle completed, convertible top closed623_055Convertible top cycle completed, convertible top closed623_056If E137 is kept pressed, the side windows raise to their closed position.The Release Button in Rear Lid Handle E234 is re-activated so the trunk lid can be opened. The rear window defroster can be switched on again.30Opening the convertible top with the vehicle keyThe convertible top can be opened and closed using the vehicle key in the driver’s door lock cylinder. The following conditions must be met: • • • • The convertible top well must be in the lower position. The trunk lid must be closed. The ambient temperature must be above 5 °F (-15 °C). The battery voltage must be sufficient.To lower the convertible top: • • Insert the key in the driver’s door lock cylinder and turn it in the “open” direction, then release. Turn the key to the “open” direction again within 2 seconds and hold it in that position.The convertible top cycle will start. The key must be held in the “open” position during the convertible top cycle. If the key is released, the cycle will immediately stop. To resume the cycle, the key must again be turned in the “open” direction and held in that position. If the key is turned in the “close” direction and held in this position, the convertible top will close again.623_057Closing the convertible top with the vehicle keyThe convertible top can also be closed using the car key. Before this can be done, the following conditions must be met: • The trunk lid must be closed. • The battery voltage must be sufficient.To close the convertible top: • • Insert the key in the driver’s door lock cylinder and turn it in the “close” direction, then release. Turn the key to the “close” direction again within 2 seconds and hold it in that position.The convertible top cycle will start. The key must be held in the “close” position during the convertible top cycle. If the key is released, the cycle will immediately stop. To resume the cycle, the key must again be turned in the “close” direction and held in that position. If the key is turned in the “open” direction and held in this position, the convertible top will open again.623_058!31Note When opening or closing the convertible top with the vehicle key, there may be a short delay between the time the key is turned to when the operation begins.Operating the convertible top while drivingThe convertible top can be opened or closed using Power Top Operation Switch E137 up to a speed of 31 mph (50 km/h). If the vehicle speed increases to over 31 mph (50 km/h) during the top cycle, the driver will be alerted both audibly and visually. The top cycle is stopped and a the top comes to a standstill in its current position. The cycle will not resume until the vehicle speed has dropped below 31 mph (50 km/h) or less. To do this, the operating switch must be kept pulled or pressed.Convertible top: not in limit position. Speed too highMessage text623_059A convertible top cycle cannot be initiated if the vehicle is travelling at a speed over 31 mph (50 km/h). In this case too, the driver is alerted by audible and visual warnings. Convertible top: no operation possible. Speed too highMessage text623_06032Components of the convertible top control systemPower Top Operation Switch E137The Power Top Operation Switch E137 is located in the center console.623_061Power Top Operation Switch E137Hall sensorsControlled operation of the convertible top is only possible if Convertible Top Control Module J256 receives information from various sensors and switches during each phase of the operating cycle. The sensors and switches indicate the current position of certain parts of the top assembly to J256. J256 uses this information to control the actuators, and thus, the operation of the top. The following Hall sensors react to the fields generated by permanents magnets: • Lower Convertible Top Compartment Enclosure Switch F520 • Left Convertible Top Closed Position Switch F411 • Right Convertible Top Closed Position Switch F412 • Convertible Top Compartment Cover -Closed- Switch F519 • Convertible Top Front Closed Position Switch F202 • Convertible Top Open Position Switch F171 • Left Tensioning Bow Switch F408Hall sensor Permanent magnetIn a Hall sensor, a magnetic field acts perpendicular to the direction of current flow in an electrical conductor resulting in voltage differences. These voltage differences are converted to signals and utilized by Convertible Top Control Module J256. The distance between a Hall sensor and permanent magnet is typically 0.1 in (3 mm).These Hall sensors are referred to as monopolar or unipolar Hall sensors. They react to the south pole of a permanent magnet.623_063Switching distance33Upper Tensioning Bow Switch F408Upper Tensioning Bow Switch F408 is a Hall-type sensor installed on the long tensioning strut pivot arm on the left hand side of the vehicle. A permanent magnet is attached to the joint on the pivot arm. When the tensioning arm reaches its upper position, F408 and the permanent magnet are facing one another. In this position, Convertible Top Control Module J256 detects that the tensioning strut is up.Upper Tensioning Bow Switch F408623_069Lower Convertible Top Compartment Enclosure Switch F520F520 is installed on the movable convertible top well at the right hand side of the vehicle. It is a Hall sensor that detects whether the movable convertible top well is in the lowered position. The convertible top cannot be opened when the movable convertible top well is in the upper position.Handle Movable convertible top wellThe convertible top well has to be manually raised or lowered by pulling or pushing on its handle. When the convertible top is closed and the top well raised, an additional 1.4 cu ft (40 liters) of load capacity is available in the trunk and greater access to the seat pass thru is available..Lower Convertible Top Compartment Enclosure Switch F520623_064Left Convertible Top Closed Position Switch F411 and Right Convertible Top Closed Position Switch F412F411 and F412 are located on the left and right hand convertible latch locks. They are both Hall sensors. Convertible Top Locking Motor V223 engages and disengages the catch hooks on the convertible top. When the catch hooks are engaged in the locks, each switch sends a signal to the Convertible Top Control Module J256 indicating the top is closed.Catch hook Convertible Top Closed Position SwitchPermanent magnet623_06534Convertible Top Compartment Cover -closed- Switch F519F519 is located on Convertible Top Compartment Cover Locking Motor V222. It is a Hall sensor. A permanent magnet is attached to the striker. When the convertible top box lid is closed, the magnet is directly facing F519. Convertible Top Control Module J256 detects that the top box lid is closed.Striker on convertible top compartmentConvertible Top Compartment Cover -closed- Switch F519623_066Convertible Top Front Closed Position Switch F202F202 is installed in the direction of travel on the stationary part of the main bearing bolted to the body on the left hand side of the vehicle. It is a Hall sensor. A permanent magnet is attached to the moving part of the main bearing. If the magnet stops within the detection range of the switch, Convertible Top Control Module J256 detects that the top is in the closed position.Permanent magnet623_067Convertible Top Front Closed Position Switch F20235Convertible Top Open Position Switch F171F171 is installed on the stationary part of the main bearing on the left hand side of the vehicle. The switch is a Hall sensor. A permanent magnet is attached to the moving part of the main bearing. If the magnet stops within the detection range of the switch, Convertible Top Control Module J256 knows that the top is in its fully open position (stowed in the convertible top compartment).Permanent magnet623_068Convertible Top Open Position Switch F171Convertible Top Compartment Cover Locking Motor V222V222 locks the convertible top box lid. It is activated by Convertible Top Control Module J256.623_070Convertible Top Compartment Cover Locking Motor V22236Convertible Top Compartment Latch -unlocked- Switch F293 and Convertible Top Compartment -locked- Switch F404Both switches are integrated in Convertible Top Compartment Cover Locking Motor V222. These switches tell Convertible Top Control Module J256 whether the convertible top box lid latch is engaged or disengaged. The microswitches are actuated by tabs on the toothed segment. This switch tells Convertible Top Control Module J256 whether the convertible top box lid latch is engaged or disengaged.Convertible Top Compartment Latch -unlocked- Switch F293623_070Convertible Top Compartment -locked- Switch F404Trunk lidThe convertible top can only be operated when the trunk lid is closed. When an opening or closing cycle is initiated, Vehicle Electrical System Control Module J519 prevents the trunk lid from being opened via the Release Button in the Rear Lid Handle E234.623_072Switch for releasing the trunk lidIf a convertible top cycle is initiated when the trunk lid is opened, a message is displayed in the DIS advising the driver to close it.Convertible top: Please close trunk lid37623_073Convertible Top Hydraulic Pump V118V118 includes: • • • • • Convertible Top Hydraulic Pump Relay J321 Convertible Top Hydraulic Pump Relay 2 J588 Power Convertible Top Valve 1 N272 Power Convertible Top Valve 2 N341 Power Convertible Top Valve 3 N342The hydraulic pump together with the relays and valves form a unit. The hydraulic pump is installed in the trunk, behind the luggage compartment trim on the left-hand side as seen in the direction of travel. The hydraulic pump is housed in an acoustic enclosure which provides sound insulation during pump operation.623_074Convertible Top Hydraulic Pump V118Convertible Top Control Module J256 controls the hydraulic pump via the two relays. The relays control the clockwise and counter-clockwise operation of the pump. This is done by operating only one of the two relays to supply power to the pump. The non-operated relay supplies the ground circuit for the pump via the 87a terminal on therelay. By switching the relay being operated, the direction of the motor is controlled which in turn changes the direction of fluid flow from the pump. The valves guide the oil flow through the hydraulic lines and into the hydraulic cylinders.Power Convertible Top Valve 2 N341 Power Convertible Top Valve 1 N272 Power Convertible Top Valve 3 N342Convertible Top Hydraulic Pump Relay J321 Convertible Top Hydraulic Pump Relay 2 J588623_11838The hydraulic system is self-locking. This means that the pressure generated by the pump is maintained within the system for approximately 5 minutes. After 5 minutes, the valves are de-energized and the hydraulic system de-pressurizes.Collision of the convertible top and convertible top box lidIf the convertible top is in an intermediate position and the hydraulic system de-pressurizes, the top will collapse depending on its position. Also, the convertible top box lid may close depending on its position. In the worst case scenario, the convertible top will collide with the convertible top box lid and may become damaged. It may happen that neither the convertible top box lid nor the convertible top reaches one of its limit positions. In this case, it is no longer possible to operate the convertible top because Convertible Top Control Module J256 receives implausible signals. When this happens, the driver will be alerted by a message in the DIS.623_076To continue operating the convertible top, the convertible top box lid must be moved manually into a limit position. The top cycle can then be resumed. If the limit position was reached by opening the convertible top box lid, it must be secured to prevent it from slamming shut. The hydraulic system can also be de-pressurized by switching the ignition off and then push or pull the Power Top Operation Switch E137 for approximately 5 seconds.623_077Power Top Operation Switch E13739Hydraulic cylindersThe convertible top and convertible top box lid are operated by three pairs of hydraulic cylinders. Two cylinders are responsible for operating the convertible top box lid. Two are responsible for the tensioning strut and two are responsible for the convertible top.Cylinder pair for tensioning strutCylinder pair for convertible topCylinder pair for convertible top box lid623_078The hydraulic cylinders operate in two working directions.Compression stageHydraulic cylinderTension stagePiston rod623_079Hydraulic connection PistonsHydraulic lineHydraulic connection40Lower Bracket Switch F517F517 is integrated in the hydraulic cylinder responsible for movement of the tensioning strut and is located on the left hand side of the vehicle. It is a Hall sensor and can be replaced separately from the cylinder. When the tensioning strut is in its lowest position (tensioned), the cylinder is fully extended. The Hall sensor then sends a signal to Convertible Top Control Module J256 that the tensioning strut is down.623_080Lower Bracket Switch F517Convertible Top Compartment -open- Switch F407F407 is integrated in the left hand side hydraulic cylinder responsible for movement of the convertible top box lid. It is a Hall sensor and can be replaced separately from the cylinder. When the convertible top box lid is fully opened, the Hall sensor sends a signal to Convertible Top Control Module J256.623_081F407 is attached to the cylinder41Hydraulic cylinders at main bearingsThe two hydraulic cylinders responsible for the movement of the convertible top are mounted at the main bearings.623_082Hydraulic cylinder of main bearing , (left hand side)Convertible Top Control Module J256Convertible Top Control Module J256J256 controls and monitors each individual convertible top operating cycle. It collects the information generated by the sensors as well as information from other data bus users. It evaluates and controls the actuators accordingly and it communicates over the Convenience CAN. J256 is located on the left hand side of the luggage compartment behind the trim cover for Convertible Top Hydraulic Pump V118.623_083J256 is also responsible for system diagnostics. If implausible signals are detected or received at the wrong time, the convertible top cycle is stopped and a DTC is recorded. A warning message to the driver is also displayed in the DIS.Convertible top: malfunction! You can continue driving623_08442To protect Convertible Top Hydraulic Pump V118 from being overloaded, its run-time is monitored by J256. If the top has been running continuously for approximately 2 minutes and is closed by this time, J256 suppresses further operation of the top for approximately 10 minutes.The maximum continuous operation of the hydraulic pump is limited to approximately 170 seconds at which time the pump shuts off regardless of the top’s current position. Further operation of the pump is subsequently suppressed for approximately 20 minutes to prevent it from overheating. The driver is warned by a message in the DIS. Convertible top: no operation possible623_085Convertible Top Locking Motor V223V223 is attached to the front of the convertible top in the middle. The motor uses a linkage to operate the two catch hooks which lock the roof to the window frame.623_086Catch hookConvertible Top Locking Motor V223Linkage43Convertible Top Latch -closed- Switch F295Convertible Top Latch -closed- Switch F295 is integrated with Convertible Top Locking Motor V223. It is a Hall sensor type switch. When V223 has locked the convertible top latches, a retaining plate is within the detection range of F295. This produces a “locked closed” signal which is sent to Convertible Top Control Module J256.Convertible Top Latch -closed- Switch F295Retaining plate623_087Convertible Top Latch -open- Switch F294F294 is also integrated with Convertible Top Locking Motor V223. It is a Hall sensor configured as an incremental encoder or rotary encoder. It measures the number of revolutions of V223. Convertible Top Control Module J256 evaluates the signals generated by the Hall sensor. When the corresponding number of revolutions have been registered, J256 detects “convertible top lock open.”Convertible Top Latch -open- Switch F294623_08844Emergency operationIn the event of a malfunction, the convertible top can be closed manually. If possible this should be done by two people. The emergency procedure cannot be done unless the hydraulic system has been de-pressurized. The system de-pressurizes automatically approximately 5 minutes after the ignition is switched off. It can also be de-pressurized by pushing or pulling Convertible Top Operation Switch E137 for approximately 5 seconds after the ignition has been switched off. Closing the convertible top Conditions: • • • • Parking brake applied All side windows lowered Ignition switched off Hydraulic system de-pressurizedThe wheel bolt wrench from the vehicle tool kit is required for manual operation of the convertible top.! !• CAUTION Be careful to prevent the top tensioning bow from striking the convertible top storage compartment cover if it is in the raised position when depressurizing the hydraulic system.CAUTION To reduce the risk of injury or damage to the vehicle, do not reach into the convertible top linkage or other moving parts during the emergency operating procedure.First, the convertible top box lid must be unlocked. To do this: Open the trunk and fold down the right seat by pulling the lever in the direction of the arrow. .623_014• Remove the wheel bolt wrench from the vehicle tool kit and close the trunk lid.From inside the vehicle, • Pull down the release loop (arrow) and unlock the convertible top box lid.623_01545• Push the covers on both sides of the vehicle in the direction of the arrow until they engage.623_016To prevent the convertible top box lid from closing involuntarily and causing injury or damage, • Move the lid into the upright position (1) and hold it there. Push back the left and right knee hinges (arrow 2) until they hold the top in its fully open position.• 623_017• Remove the trim cover and insert the wheel bolt wrench.To open or disengage the catch hooks, • Turn the box wrench clockwise as far as it will go and then remove it.623_018• Lift out the convertible top completely (in the direction of the arrow) by grabbing it from the front edge. Raise the convertible top tensioning strut until the convertible top box lid can be closed.• 623_01946Note: Two people should always perform this procedure to avoid the risk of injury or damage to the convertible top components. • Release the convertible top box lid (1) by pulling the hinges forward and slowly lowering the lid until it closes. Lower the tensioning strut (2) until it rests on the convertilbe top box lid.• 623_020• Push the convertible top firmly into the windshield frame (arrow).623_021• Insert the wheel bolt wrench and turn it counter clockwise until the latch hooks are fully engage in the windshield frame. Remove the wrench and stow it in the vehicle tool kit.• 623_022Reference Please refer to the Owner’s Manual for further information on emergency operation.47Data bus overviewThe overview shows the information exchanged via data bus.Instrument Cluster Control Module J285 Display convertible top message in the DIS ← I Ambient temperature → O Driver Side Rear Window Regulator Motor Control Module J1016 Front Passenger Side Rear Window Regulator Motor Control Module J1017 Side window closing ← I Lower side windows ← I (LIN users of door control units J386 and J387)Driver Door Control Module J386 Passenger Door Control Module J387 Locked and closed status of convertible top ← I Side window closing ← I Lower side windows ← I Side window closing → O (to LIN users J1016 and J1017) Side window opening → O (to LIN users J1016 and J1017)Vehicle Electrical System Control Module J519 (= BCM_01) Locked and closed status of convertible top ← I Locked and open status of convertible top ← I Convertible top in intermediate position ← I Trunk lid release enabled/disabled ← I Comfort request via key ← I Rear window heater on/off status → O NO contact on/off status → O Terminal 15 status → O Convenience opening and closing request signal → O Enable convertible top operation → O Actual and nominal status of external vehicle locking → O Trunk lid status → O Sleep mode readiness → OConvertible Top Control Module J256 Locked and closed status of convertible top ← O Unlocked status of convertible top ← O Locked and open status of convertible top ← O Convertible top in intermediate position ← O Convertible top opening movement ← O Convertible top closing movement ← O Trunk lid release enabled/disabled ← O Side window closing → O Lower side windows ← O Display convertible top message in the DIS → O Comfort request via key ← O Speed signal → I Ambient temperature → I Convenience opening and closing request signal → I Sleep mode readiness → I Rear window heater on/off status → I NO contact on/off status → I Terminal 15 status → I Enable convertible top operation ← I Trunk lid status → I Actual and nominal status of external vehicle locking → IClimatronic Control Module J255 Locked and closed status of convertible top ← I Locked and open status of convertible top ← I Convertible top opening movement ← I Convertible top closing movement ← IData Bus On Board Diagnostic Interface J533 (Gateway) Locked and closed status of convertible top ← I Unlocked status of convertible top ← I Locked and open status of convertible top ← I Comfort request via key ← I Speed signal → O Sleep mode readiness → OAccess/Start Authorization Control Module J518 Locked and closed status of convertible top ← I Convertible top opening movement ← I Convertible top closing movement ← I Comfort request via key ← IKey: Data bus in general LIN busTrailer detector control unit J345 Comfort request via key ← E623_071← I → O Receiving data (input) Sending data (output)48Occupant protectionThe A3 Cabriolet has the following occupant protection equipment: • Airbag Control Module • Driver and passenger front airbags • Front side airbags (head/thorax airbag) • Knee airbags • Front airbag crash sensors • Side impact sensors in the front doors • Centrally located rear side impact sensor • Front inertia reel safety belts with electric and pyrotechnic tensioners • Safety belt warning for all seats • Front passenger seat occupancy detection sensor • Rollover protection623_005Key for following page E24 E25 E258 E259 G452 G179 G180 G256 G283 G284 G551 G552 G553 G554 J234 J285 J533 J706 J854 J855 Driver Seat Belt Switch Front Passenger Seat Belt Switch Driver Side Rear Seat Belt Switch Passenger Side rear Seat Belt Switch Front Passenger Seat Occupant Sensor Driver Side Airbag Crash Sensor Front Passenger Side Airbag Crash Sensor Centrally located Rear Side Airbag Crash Sensor Driver Front Airbag Crash Sensor Passenger Side Front Airbag Crash Sensor Driver Belt Force Limiter Front Passenger Belt Force Limiter Driver Seat Position Sensor Passenger Seat Position Sensor Airbag Control Module Instrument Cluster Control Module Data Bus On Board Diagnostic Interface Passenger Occupant Detection System Control Module Left Front Seat Belt Tensioner Control Module Right Front Seat Belt Tensioner Control Module N95 N131 N132 N153 N154 N199 N200 N295 N296 N297 N298 N646 N647 T16 Driver Airbag Igniter Front Passenger Airbag Igniter 1 Front Passenger Airbag Igniter 2 Driver Seat Belt Tensioner Igniter 1 Front Passenger Seat Belt Tensioner Igniter 1 Driver Thorax Airbag Igniter Front Passenger Thorax Airbag Igniter Driver Knee Airbag Igniter Front Passenger Knee Airbag Igniter Driver’s Seat Belt Tensioner Igniter 2 Front Passenger Seat Belt Igniter 2 Driver Side Rollover Protection Igniter Front Passenger Side Rollover Protection Igniter Data Link ConnectorPowertrain CAN bus Convenience CAN bus Diagnostics CAN bus Input signal Output signalK19 Seat Belt Indicator Lamp K75 Airbag Indicator Lamp K145 Front Passenger Airbag Disabled Indicator Lamp49623_006a50Side airbagThe front driver and passenger side airbags are designed as head thorax airbags. They are designed to protect the body and head of the front occupant. By integrating the side airbags in the front seat backrests, the occupant is optimally positioned relative to the front occupants irrespective of their seating adjustment.623_011The side airbags are activated by Airbag Control Module J234. The signal first ignites the priming charge which in turn ignites the solid propellant.The gases expelled during the combustion of the propellant charge flow through the outlet orifices via the filter into the airbag which unfolds and fully inflates. The seal between the outlet orifices protects the pyrotechnic material from moisture and is destroyed by the heat generated.Seal Filter (contains the propellant charge)Priming charge623_012IgniterPropellant chargeOutlet orifices51Electrical wiring harness for side airbagThe electrical wiring harness for the front side airbags can now be replaced without replacing the complete airbag module if it is damaged. This is because the ground wire used to protect the pyrotechnic devices from static connects directly to the airbag module. When connected, the ground wire connects the gas generator housing to the vehicle body.Cover Locking deviceContactMechanically encoded housing609_014a 609_014Driver Side Rear Side Airbag Crash Sensor G256G256 is a capacitive acceleration sensor. Although it is designated as being for the driver’s side rear, it is installed at the center of the back seat area. If G256 senses a side impact, it sends its signal to Airbag Control Module J234. The ‘Y’ sensor in the Airbag Control Module performs a plausibility check. If a deployable impact is detected, the Airbag Control Module deploys the safety belt tensioners.Driver Side Rear Side Airbag Crash Sensor G256623_01352Rollover protectionThe A3 Cabriolet is equipped with a rollover protection system. Together with the strength of the body and rigid A-pillars, a protective area is created for the occupants during a rollover accident. An additional sensor detects an imminent rollover and deploys the protection system. The sensor is located in Airbag Control Module J234 and cannot be replaced separately. If an imminent rollover is detected, the protection system is deployed and the pyrotechnic safety belt tensioners are ignited. In all crash events in which the airbags and/or safety belt tensioners are ignited, the rollover protection deploys as a precautionary measure. If no rollover occurs in the course of the event, the system can be reset.623_005a53Cassettes with protective roll barsThe rollover protection system on the A3 Cabriolet consists of two cassettes that hold the protective roll bars and other components. Different cassettes are used for the driver and passenger side of the vehicle. The cassettes must be installed on the correct side of the vehicle. The correct installation direction of each cassette is indicated by a stamped arrow. A specific tightening sequence must be followed when they are installed.Arrow indicating installation direction SpringRelease lever CassetteRatchet railPawl623_007Driver Side Rollover Protection Igniter N646 and Front Passenger Side Rollover Protection Igniter N647The retractable protective roll bars are pre-loaded by a spring. The bar is held in its lowered position by the U bar of the rollover protection trigger. When the trigger is energized by Airbag Control Module J234, it releases the U bar and the bar deploys upward in approximately 130 milliseconds. When the protective roll bar reaches its fully extended position, a pawl engages the ratchet rail and locks the bar in position.U barSpring623_008Rollover protection triggerRollover protection trigger54When the convertible top is open, the protective roll bar travels approximately 12.5 in (320 mm) when it is deployed. When the convertible top is closed, the travel of the bar is limited and it deploys approximately 7.4 in (190 mm). This helps minimize damage to the convertible top.Attaching pointsRatchet railSpringPawl623_009Preloaded positionFully extended position when convertible top is closedFully extended position when convertible top is open55Resetting a deployed protective roll barPulling the release lever 1 pulls the pawl 2 out of the ratchet rail 3 and releases the bar. The rollover protection system can be reset by pushing back the bar 4 at the same time (the U bar must lock into place).1423623_010DiagnosticsN646 and N647 are monitored by Airbag Control Module J234. The Airbag Control Module records each deployment of the rollover protection system. The protection system can be tested by deploying through an Output check diagnosis using the VAS Scan Tool. The number of deployments is limited and can be read from the MVBs. Once 127 deployments have been recorded, a DTC (rollover protection system faulty) is registered by J234 and the cassettes have to be replaced. Therefore, unnecessary deployments should be avoided. Please consult the maintenance schedule to determine when a check of the system should be performed.Reference For further information about the rollover protection system, refer to the Electronics Service Information, Guided Fault Finding and the maintenance schedule.56Engines1.8L and 2.0L TFSI enginesTechnical feature overviewCylinder head with Integrated Exhaust Manifold (IEM)609_156_a2.0L TFSI engine shown. The 1.8L TFSI engine does not have continuously adjustable exhaust camshaft timing.Optimized thermal managementEngine Temperature Control Actuator N493609_156_b57Both the 1.8L TFSI and 2.0L TFSI engines for the North American market will only have the FSI injection system. The dual injection may be introduced at a later date.Combined FSI/MPI injection609_156_cFriction optimization and lightweight design609_156609_156_dReference For detailed information about the 1.8L and 2.0L TFSI engines, please see eSelf-Study Program 920243, Third generation Audi 1.8L and 2.0L engines from the EA888 model family.58Engine/transmission combinations1.8l TFSI engineOD9 front2.0l TFSI engine0D9 quattro59Notes60SuspensionOverall conceptBy using key suspension components from the 2015 A3 sedan, special emphasis was placed on lightweight design as part of the Audi Ultra Strategy. Some suspension components are made from aluminum.623_103The front and rear axle carriers are connected to the car body by additional cross pieces. This provides a high level of vehicle rigidity and reduction of vibration.623_10461OverviewContinental ESC MK100 second generation tire pressure monitoring systemThree-spoke sports wheel in various versions as options 17” wheels standard, 18” and 19” optional on some models15“ or 16” inch brakes standard623_10515" rear wheel brakes with electro-mechanical parking brake (EPB)Four-link rear axle for front wheel drive and quattro driveACC is optionalMacPherson strut front axle in combina tion with aluminum sub frame and steering knuckle.Electro-mechanical steering with Servotronic function as standardTandem master brake cylinder with single 10“ or 11“ brake servoReference For detailed information about the design and function of the electro-mechanical steering system, refer to eSelf-Study Program 960143, The 2015 Audi A3Running Gear and Suspension System.62Electrical systemInstallation locations of control modulesSome of the control modules shown in the overview may be optional or country specific and not available in the North American market. Refer to the current service literature for details of control module positions, as well as instructions for installation and removal.J387J668 J104J794J250J500R242 J428 J685 J234 E380 J587J518 J745 J533 J527 J764 J525J285J623J791 J667 J519J386Key:E380 Multimedia System Control Head J104 J234 J250 J255 J256 J285 J386 J387 63ABS/ESP Control Module Airbag Control Module ECD Control Module (electronically controlled damping) Climatronic Control Module Convertible Top Operation Control Module Instrument Cluster Control Module Driver Door Control Module Passenger Door Control ModuleJ428 J492 J500 J518 J519 J525 J527 J533 J527 Distance Regulation Control Module All Wheel Drive Control Module Power Steering Control Module Access/Start Authorization Control Module Vehicle Electrical System Control Module 1 Digital Sound System Control Module Steering Column Electronics Control Module Data Bus On Board Diagnostic Interface (Gateway) Steering Column Electronics Control ModuleJ1017J772J769J492J770J256 J1016623_097J623 J667 J668 J685 J745 J764 J769 J770 J772 Engine Control Module Left Headlamp Power Output Stage Right Headlamp Power Output Stage Front Information Display Control Head Cornering Lamp and Headlamp Range Control Module Electronic Steering Column Lock Control Module Lane Change Assistance Control Module Lane Change Assistance Control Module 2 Rear View Camera System Control ModuleJ791 Parallel Parking Assistance Control Module J794 Information Electronics Control Module 1 J1016 Rear Driver Side Window Control Module J1017 Rear Passenger Side Window Control Module R242 Driver Assistance Systems Front Camera64TopologyLight switch E1Left Headlamp Power Output Stage J667Anti-theft Alarm System Sensor G578Wiper Motor Control Module J400Right Headlamp Power Output Stage J668orAlarm horn H12Rain/Light Recognition Sensor G397Humidity sensor G355Power Output Module for Left LED HeadlightLeft Head Area Heater Control Module J846Vehicle Electrical System Control Module J519Power Output Module for Right LED HeadlightRight Head Area Heater Control Module J847Instrument Cluster Control Module J285Convertible Top Control Module J256Lane Change Assistance Control Module 2 J770Steering Column Electronics Control Module J527 Data Link ConnectorRear Passenger Side Window Control Module J1016Driver Door Control Module J386Rear Driver Side Window Control Module J1017Passenger Door Control Module J387Data Bus On Board Diagnostic Interface J533 (Gateway)Trailer detector control unit J345Nox Sensor Control Module J583* Engine Control Module J623 Nox Sensor Control Module 2 J881*Access/Start Authorization Control Module J518 Electronic Steering Column Lock Control Module J764Passenger Occupant Detection System Control Module J706 Left Front Seat Belt Tensioner Control Module J854Airbag Control Module J234Vehicle tracking system interface control unit J843Special vehicle control unit J608Right Front Seat Belt Tensioner Control Module J855Climatronic Control Module J255Transmission Control Module J217Selector Lever Sensor System Control Module J587Refrigerant Circuit Pressure Sensor G805Fresh Air Blower Control Motor J126Humidity Sensor in Fresh Air Intake Duct G657Air quality sensor G238Structure-Borne Sound Control Module J86965*TDI engine