TECHNICAL DOCUMENTATION

SSP 970153 – The 2016 Audi TT Vehicle Electrics, Electronics, and Infotainment Systems

PDFEN76 pages5 MB
SSP 970153 – The 2016 Audi TT Vehicle Electrics, Electronics, and Infotainment Systems - PDF cover

This PDF is currently unavailable.

Read document text
eSelf Study Program 970153The 2016 Audi TT Vehicle Electrics, Electronics, and Infotainment Systemsi Audi of America, LLC Service Training Created in the U.S.A. Created 05/2015 Course Number 970153 ©2015 Audi of America, LLC All rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC. Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.This eSSP contains video links which you can use to access interactive media.Revision 1: 5/2015ii Introduction ...................................................................................... 1 Power supply...................................................................................... 2Battery ........................................................................................................................................................................2 Positive battery cable ................................................................................................................................................2 Fuses, fuse holder and jump start terminal ...........................................................................................................4Networking......................................................................................... 6Topology .....................................................................................................................................................................6 Overview of bus systems ...........................................................................................................................................8 New features of the bus systems .............................................................................................................................8 Optical bus system MOST150 ...................................................................................................................................9 Special tool .................................................................................................................................................................9Control units..................................................................................... 10Brief descriptions .................................................................................................................................................... 10Exterior lights................................................................................... 26Headlights ............................................................................................................................................................... 26 Headlight range adjustment .................................................................................................................................. 28 Tail lights ................................................................................................................................................................. 29 High-level brake light / license plate light ........................................................................................................... 30Vehicle electronics............................................................................ 31Car key ..................................................................................................................................................................... 31 Keyless starting system ......................................................................................................................................... 31 Terminal 15 power supply ..................................................................................................................................... 32 Advanced Key .......................................................................................................................................................... 34 Implementation of keyless entry and start systems at Audi ............................................................................. 34 System processes in the keyless start system ..................................................................................................... 36 System processes in the keyless entry system (Advanced key) ......................................................................... 42 Immobilizer ............................................................................................................................................................. 45 Electronic Steering Column Lock Control Module J764 ....................................................................................... 46 Electrical rear spoiler ............................................................................................................................................. 47 Overhead module ................................................................................................................................................... 48 Interior light ............................................................................................................................................................ 50Infotainment.................................................................................... 52Overview of versions ............................................................................................................................................... 52 Second-generation MIB High ................................................................................................................................. 54 MMI radio ................................................................................................................................................................ 55 MMI radio with connectivity package .................................................................................................................. 56 MMI Navigation plus .............................................................................................................................................. 57 Audi connect ........................................................................................................................................................... 58 Networking .............................................................................................................................................................. 59 Display and operating concept .............................................................................................................................. 60 Control panel ........................................................................................................................................................... 61 Sound systems ........................................................................................................................................................ 63 Antenna overview ................................................................................................................................................... 66Self study programs......................................................................... 70 Knowledge Assessment................................................................... 71This eSelf Study Program teaches a basic knowledge of the design and functions of new models, new automotive components or technologies. It is not a Repair Manual! All values given are intended as a guideline only. For maintenance and repair work, always refer to the current technical literature.NoteReferenceiii iv IntroductionAll versions of the new Audi TT come with a generous range of standard equipment. On the infotainment front, customers can choose from a wide range of options. The connectivity package features the MMI touch system incorporating a touch-sensitive touch pad. At the top of the modular range is the MMI Navigation plus with its large flash memory, two card readers, DVD drive, Bluetooth interface and voice control system. The T30 chip from the Tegra 3 series by market leader Nvidia, which is installed in the new-generation Modular Infotainment System, controls all in-car navigation and multimedia functions and displays content in the Audi virtual cockpit. The Audi connect system complements the MMI Navigation plus perfectly – it connects the new Audi TT to the internet using the high-speed LTE transmission standard. The integrated Wi-Fi hotspot means passengers can surf the internet and E-mail as they please, while the driver can rely on the customized Audi connect services. An optional Bang & Olufsen Sound System features a 14-channel amplifier and 12 loudspeakers; the bass loudspeakers in the doors are illuminated discretely by fiber optics. Highly intelligent assistance systems make driving the new TT an even more pleasurable experience. As an option, the car can be equipped with Audi side assist, which uses rearmounted radar sensors to help drivers change lane more safely.1 Power supplyBatteryThe battery of the Audi TT is housed in the rear of the vehicle. Battery size and type are dependent on engine version, trim and country specification. Attached to the battery positive terminal is the main fuse box and Battery Interrupt Igniter N253. Battery Monitoring Control Module J367 (BDM) is mounted on the negative battery terminal. If the battery is replaced it must be adapted (encoded) to J367 using the VAS Scan Tool.Positive battery cableThe positive battery cable is an advanced aluminum ribbon cable with high flexural rigidity. It is coated with a red plastic insulating layer. Apart from its light weight, this type of main battery lead has other advantages as well: • Because of the shape and rigidity of the rail, there is no need for additional routing devices. • No cable ducts are required. • More efficient use is made of available space.2 629_002The positive battery cable leaves the battery positive terminal as a flexible, round-section lead. It is routed out of the vehicle interior through a cable sleeve, becoming a ribboncable in the rear axle area and ending at the jump start terminal on the left hand side of the engine compartment. From there, wires go to the E-box, starter and alternator.3 Fuses, fuse holder and jump start terminalIn addition to standard flat fuses, space saving mini-fuses and circuit breakers (thermal fuses), the TT uses the new J-Case fuse like those of the 2015 Audi A3. These fuses are, like the standard and mini fuses, identified in different colors.J-Casefuses629_003Fuse rail on the E-box Fuses are marked “SA” in the Wiring Diagrams.Jump start connectionSeveral fuses with different ratings are grouped together to form a fuse strip or multi-fuse. The fuses protect the alternator, electromechanical power steering and the radiator fans. In the event of a fault, the complete multi-fuse must be replaced.E-box with fuses and relays Fuses are marked “SB” in the Wiring Diagrams.4 Fuse holder at battery positive terminal. Fuses are marked “S” in the Wiring Diagrams. Battery Interrupt Igniter N253 also located here.629_004Fuse holder and relay panel under the instrument panel. Fuses are marked "SR" in the Wiring Diagrams. Fuse holder and relay panel under the instrument panel, left. Fuses are marked “SC” in the Wiring Diagrams.5 NetworkingTopologyLight Switch E1 Alarm Horn H12 Anti-theft Alarm System Sensor G578Wiper Motor Control Module J400Garage Door Opener Control Head E284Rain/Light Recognition Sensor G397 Humidity Sensor G355 Vehicle Electrical System Control Module 1 J519 Steering Column Electronics Control Module J527 Convertible Top Control Module J256 (Roadster only) Instrument Panel Control Module J285Garage Door Opener Control Module J530 Drive Multi-contour Seat Control Module J873Driver Door Control Module J386Front Passenger Multi-contour Seat Control Module J872 Left Head Area Heater Control Module J846 Right Head Area Heater Control Module J847Front Passenger Door Control Module J387Driver Volume Control E67Multi-media System Control Head E380Electronic Steering Column Lock Control Module J764 Access/Start Authorization Control Module J518Data Bus On Board Diagnostic Interface J533Selector Lever Sensor System Control Module J587ABS/ESP Control Module J104Engine Control Module J623Electronic Damping Control Module J250Front A/C Display Control Head 1 E774Climatronic Control Module J255DSG Transmission Mechatronic J743All Wheel Drive Control Module J492Front A/C Display Control Head 2 E775Fresh Air Blower Control Module J126Structure Borne Sound Control Module J869 Passenger Occupant Detection System Control Module J706 Airbag Control Module J234Power Steering Control Module J500Front A/C Display Control Head 3 E776Refrigerant System Pressure Sensor G805Parking Aid Control Module J446Front A/C Display Control Head 4 E777Humidity Sensor in Fresh Air Intake Duct G657 Air Quality Sensor G238Front A/C Display Control Head 5 E7786 The topology shows all control modules with connectivity to the bus systems.Some of the control modules shown here are optional or country-specific equipment or due to be introduced at a later date.Digital Sound System Control Module J525Automatic High Beam Assist Control Module J844orInformation Electronics Control Module 1 J794 Rearview Camera System Control Module J772 Seat Belt Microphone Control Module J886Driver Assistance Systems Front Camera R242Lane Change Assistance Control Module J769 Battery Monitoring Control Module J367 Data Link Connector Alternator CLane Change Assistance Control Module 2 J770Headlamp Range Control Module J431orCornering Lamp and Headlamp Range Control Module J745Multi-Function Steering Wheel Control Module J453Left LED Headlamp Power Output Module 1 A31 Left Headlamp Power Output Stage J667Right LED Headlamp Power Output Module 1 A27 Right Headlamp Power Output Stage J668orParallel Parking Assistance Control Module J791631_062Key: Powertrain CAN bus Convenience CAN bus Extended CAN bus "OR" configuration Infotainment CAN bus Diagnostics CAN bus Suspension CAN bus Modular infotainment system (MIB) LIN bus Sub-bus systems MOST bus7 Overview of bus systemsCable colorBus system Powertrain CAN bus Convenience CAN bus Extended CAN bus Infotainment CAN bus Suspension CAN bus Modular infotainment system CAN Diagnostics CAN bus MOST busConfiguration Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Optical bus system Electrical single-wire bus system Electrical two-wire bus systemMax. data transfer rate 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/sProperty Not single wire capable Not single wire capable Not single wire capable Not single wire capable Not single wire capable Not single wire capable Not single wire capable Ring structure: an open circuit leads to total system failure Capable of single-wire operation Not single wire capable150 Mbit/sLIN bus Sub-bus system20 kbit/s 500 kbit/sNew features of the bus systems• The convenience CAN and the infotainment CAN in the Audi TT are high-speed bus systems. • New CAN bus: Modular Infotainment System (MIB) CAN. • New MOST bus: MOST150. • Instrument Cluster Control Module J285 is a convenience CAN bus user and a MOST150 user, and is connected to Information Electronics Control Module 1 J794 via the Modular Infotainment System CAN. • The Data Bus On Board Diagnostic Interface J533 is the master of LIN slave Multi-function Steering Wheel Control Module J453. • J533 interface is not integrated into the MOST bus. • Information Electronics Control Module 1 J794 is the system and diagnostic manager for the MOST bus. • Information Electronics Control Module 1 J794 is connected to the Multi-media System Operating Button E380 and Instrument Cluster Control Module J285 via the Modular Infotainment System CAN via the Modular Infotainment System CAN.The networking diagram on the previous pages provide a schematic overview of the communication paths of the in-car control modules. Which control modules are installed in the vehicle depends on its optional equipment level.Here are a two examples: • Automatic High Beam Assist Control Module J844 is never installed together with Drive Assistance Systems Front Camera R242. • Passenger Occupant Detection System Control Module J706 is only used in the North American Region.8 Optical bus system MOST150HistoryThe MOST optical data bus was installed first in the 2004 Audi A8. The data bus system is named after the Media Oriented Systems Transport (MOST) Cooperation. This organization is composed of various automobile manufacturers, their component suppliers and software companies who joined forces to create a standardized high speed data transfer system. The term "Media Oriented Systems Transport" denotes a network with media-oriented data transport. This means that, unlike in the CAN bus, address-oriented messages are sent to a specific recipient. This technology is used in Audi vehicles to transfer data within the infotainment system. The data transfer rate on the MOST25 bus is approximately 25 Mbit/s.MOST150An advancement of the MOST technology, MOST150, was first introduced in North America in the 2015 Audi A3. MOST150 is six times faster than the MOST25 bus. The development process necessitated making various modifications to the components of the MOST bus. For example, the transmitter and receiver units - Fiber Optical Transmitters (FOT) - had to be adapted. Other components such as optical connectors, the fiber optic cables and the electrical connectors of the control modules are identical to those of the MOST25 system.System managerUp to four control modules are integrated into the MOST bus in the Audi TT: • Information Electronics Control Module 1 - J794. • Instrument Cluster Control Module J285. • TV tuner R78 (not used in the North American market). • Digital Sound System Control Module J525. Information Electronics Control Module 1 J794 serves two functions: • • It is the system manager for the MOST bus. It is the diagnostic manager replacing Data Bus On Board Diagnostic Interface J533.Instrument Cluster Control Module J285TV tuner R78* *not for USDigital Sound System Control Module J525Information Electronics Control Module 1 J794629_006Special toolDiagnosticsThe ring break diagnosis procedure is identical to that of the MOST25 bus system. However, the Test Plans are found under Address Word 5F on the VAS Scan Tool. Even though the ring break diagnosis procedure remains unchanged, a modified tool – VAS 6778 – must be used in the event of an optical fault in the MOST150 bus because the transmitter and receiver units in the control modules have been modified.629_0079 Control unitsBrief descriptionsOnboard power supply control unitDesignation Equipment Installation location Vehicle Electrical System Control Module 1 J519 Always installed Under the instrument panel, left-hand side Central locking master Exterior light master Interior light master Anti-theft alarm / optional equipment master, PR No.: 7AL Activation of various relays Activation of various convenience components: • Seat heaters • Heated windshield washer spray jets • Windshield washer pump • Headlight washer system pump • Monitoring various switches and buttons • Monitoring various sensors 09 • Convenience CAN bus user • J519 is the LIN master for: • LIN 1 – Rain/light Recognition Sensor G397, Humidity Sensor G355, Wiper Motor Control Module J400 and Light Switch E1 • LIN 2 – Alarm Horn H12 • LIN 3 – Anti-theft Alarm System Sensor G578 and Garage Door Opener Control Head E284 • LIN 4 – Garage Door Opener Control Module J530; Front Driver and Passenger Multi-contour Seat Control Modules J872 and J873 Duplicated pins on LIN 1 and on LIN 4 Description on the next page • • • • • • TasksAddress WordData bus communicationSpecial featureJ519629_008Reference For a detailed description of Vehicle Electrical System Control Module 1 J519, see eSelf-Study Program 970343, The 2015 Audi A3 Vehicle Electronics and Driver Assistance Systems.10 Duplicated pins on J519LIN 1 is distributed to two pins at J519 (duplicated pin). Wiper Motor Control Module J400 is connected to pin B30. Connected to pin C28 are the Light Switch E1 and the combination sensors Rain/Light Recognition Sensor G397 and Humidity Sensor G355. This means that the control modules connected to pin C28 are also affected in the event of a short circuit to positive or negative at pin B30. LIN 4 is also distributed to two pins on Vehicle Electrical System Control Module 1 J519. Garage Door Opener Control Module J530 is connected to pin B29. The MultiContour Seat Control Modules J872 and J873 are both connected to pin A42. This means that the control modules connected to pin A42 are also affected by a short circuit to positive or negative at pin B29, and vice versa.Rain/Light Recognition Sensor G397Humidity Sensor G355Light Switch E1Alarm Horn H12Wiper Motor Control Module J400C28B30B31LIN branch 1 Vehicle Electrical System Control Module 1 J519 LIN branch 3LIN branch 2LIN branch 4A15A42B29Garage Door Opener Control Head E284Front Passenger Multi-contour Seat Control Module J872Anti-theft Alarm System Sensor G578Driver Multi-contour Seat Control Module J873Garage Door Opener Control Module J530629_00911 GatewayDesignation Equipment Installation location Data Bus On Board Diagnostic Interface J533 Always installed Under the instrument panel, left-hand side • • • • 19 • User of all CAN bus systems • LIN master of Battery Monitoring Control Module J367 and the Alternator • LIN master of Multi-function Steering Wheel Control Module J453 Not a MOST bus user Network system gateway Diagnostic master (with the exception of MOST150 bus) Energy management system control Multifunction steering wheel masterTasksAddress Word Data bus communication Special featureJ533629_010Audi virtual cockpitDesignation Equipment Installation location Tasks Address Word Data bus communication Special feature Instrument Cluster Control Module J285 Always installed In the instrument panel (not integrated with Audi virtual cockpit) • Display of information relevant to the driver • Immobiliser master 17 Convenience CAN bus user and MOST150 user and connected to the Information Electronics Control Module 1 - J794 via the Modular Infotainment System CAN Also displays all content shown on the MMI screen in other vehiclesJ285629_011For a detailed description of the Audi virtual cockpit, please refer to eSelf Study Program 910153 "Audi Virtual Cockpit".12 Steering column electronicsDesignation Equipment Installation location Task Address Word Data bus communication Special feature Steering Column Electronics Control Module J527 Always installed On the steering column • Connecting the steering column stock and the electrical components in the steering wheel to the vehicle electronics 16 Convenience CAN bus user Transfers the LIN signals from Data Bus On Board Diagnostic Interface J533 (master) to the Multifunction Steering Wheel Control Module J453 (slave)Data Bus On Board Diagnostic Interface J533Steering Column Electronics Control Module J527 J527 Spiral Spring F350Multi-function Steering Wheel Control Module J453629_012629_013Sound actuatorDesignation Equipment Installation location Task Address Word Data bus communication Structure Borne Sound Control Module J869 Depending on engine version In the plenum chamber, right-hand side, beneath the windshield Producing a sporty engine sound for the vehicle occupants A9 Powertrain CAN bus userJ869629_01413 Air conditioning systemDesignation Equipment Installation location Climatronic Control Module J255 Standard equipment: automatic climate control, PR No.: 9AK On the instrument panel cross-member Controlling: • Temperature • Blower • Air flow distribution 08 • Convenience CAN bus user • J255 is the LIN master for: • LIN 1 – Fresh Air Blower Control Module J126, Refrigerant Circuit Pressure Sensor G805, Humidity Sensor in Fresh Air Intake Duct G657 and Air Quality Sensor G238 • LIN 2 – Front A/C Display Control Head 1 E774 to Front A/C Display Control Head 5 E778 The control module is separate from the operating and display componentsTasksAddress WordData bus communicationSpecial featureJ255629_01514 Door electronics, driver sideDesignation Equipment Installation location Task Address Word Data bus communication Special features Driver Door Control Module J386 Always installed In the driver's door Controlling the electrical and electronic components in and on the driver's door 42 Convenience CAN bus user • J386 acts as the substitute master for the central locking system in the event of failure of Vehicle Electrical System Control Module 1 J519 • Activates the side turn signal in the driver's door mirrorJ386629_016Door electronics, passenger sideDesignation Equipment Installation location Task Address Word Data bus communication Special feature Front Passenger Door Control Module J387 Always installed In the front passenger's door Controlling the electrical and electronic components in and on the front passenger's door 52 Convenience CAN bus user Activates the side turn signal in the front passenger door mirrorJ387629_01715 Advanced key / keyless entry and start authorizationDesignation Equipment Installation location Tasks Address Word Data bus communication Special feature Access/Start Authorization Control Module J518 Standard equipment: keyless start Optional equipment: keyless entry, PR No.: 4F2 Under the instrument panel • Monitoring both capacitive sensors • Activation of the entry and start authorization antennas B7 Convenience CAN bus user Exterior antennas are installed on the vehicle underbody in the B post areaJ518629_01816 Electrical steering column lockDesignation Equipment Installation location Task Address Word Data bus communication Special features Electronic Steering Column Lock Control Module J764 Always installed On the steering column • Locking and unlocking the steering column 2B Convenience CAN bus user • Can be replaced separately from the steering column • Immobilizer userJ764629_020Back-up cameraDesignation Rearview Camera System Control Module J772 Optional equipment Versions: • Parking aid plus with back-up camera, PR No.: 7X2+KA2 • Parking aid with back-up camera, PR No.: 7X5+KA2 In the handle on the trunk lid • Rectification and processing of raw images captured by the camera • Transfer of processed images to Information Electronics Control Module 1 J749 6C Infotainment CAN bus user No need for a separate control module, control module and camera are integrated in a single housingEquipmentInstallation location Tasks Address Word Data bus communication Special featureJ772629_02117 InfotainmentDesignation Information Electronics Control Module 1 J794 MMI radio as standard equipment, PR No.: I8E+7UH Optional equipment Versions: • MMI touch, PR No.: UJ1 • MMI Navigation plus, PR No.: I8H+7UG In the glove compartment Controlling the infotainment systems 5F • Infotainment CAN bus user • MOST bus user • J794 is connected to the Multi-media System Operating Button E380 and to Instrument Cluster Control Module J285 via the Modular Infotainment System CAN. • No need for a separate MMI display, all content is displayed in the Audi virtual cockpit • J794 is the system manager and the ring break diagnostics master for the MOST busEquipmentInstallation location Task Address WordData bus communicationSpecial featuresJ794629_022Sound amplifierDesignation Equipment Installation location Task Address Word Data bus communication Digital Sound System Control Module J525 Optional equipment for models with Bang & Olufsen Sound System, PR No.: 9VS Under the driver’s seat Driving the 12 loudspeakers 47 MOST bus userJ525629_02318 Electronic Stabilization Program (ESP)Designation Equipment Installation location ABS/ESP Control Module J104 Always installed • In the engine compartment, on right-hand side of engine bulkhead in left-hand-drive models • • • • • • • 03 Suspension CAN user • The control module can be replaced separately from the valve block using ESD protective mat VAS 6613 • The electro-mechanical parking brake is integrated into the ABS/ESP Control Module. Address Word 53 for electro-mechanical parking brake has been deleted. Anti lock braking system (ABS) Electronic Stabilization Program (ESP) Traction Control System (TCS) Electronic Differential Lock (EDL) Electronic transverse lock Multicollision brake Electro-mechanical parking brake (EPB)TasksAddress Word Data bus communicationSpecial featuresJ104 Valve block629_02519 Power steeringDesignation Equipment Installation location Power Steering Control Module J500 Always installed Connected to the steering gear • • • • 44 Suspension CAN user • The control module with power steering motor as well as Steering Angle Sensor G85 can only be replaced together with the steering gear • G85 has no separate data bus connections; data is transferred through Power Steering Control Module J500 Power steering Servotronic speed-responsive power steering Corrective steering intervention, with Audi active lane assist and park assist Corrective steering intervention, with ESPTasksAddress Word Data bus communicationSpecial featuresJ500629_026All-wheel driveDesignation Equipment Installation location Task Address Word Data bus communication Special features All Wheel Drive Control Module J492 Standard equipment with quattro powertrain Connected to the rear axle gear Controlling the Haldex coupling depending on the driving situation 22 Suspension CAN user • The control module can be replaced separately and without removing the rear axle gear • The Haldex coupling setup can be selected via Audi drive selectJ492629_02720 Parking aid/ park assistDesignation Parking Aid Control Module J446 Parallel Parking Assistance Control Module J791 Optional equipment Versions: • Rear parking aid, PR No.: 7X1 • Parking aid plus, PR No.: 7X2 Behind the instrument panel, left-hand side • Monitoring the ultrasound sensors and, depending on version, audible or visual obstacle warnings 76 Suspension CAN user The diagnostic address is now 76, instead of Address Word 10 on previous Audi modelsEquipmentInstallation location Tasks Address Word Data bus communication Special featureJ446 / J791629_028Audi magnetic ride (TTS)Designation Equipment Installation location Task Address Word Data bus communication Electronic Damping Control Module J250 Optional equipment, PR No.: 1BL Under the right-hand front seat Adaptation of the damping characteristic 14 Suspension CAN userJ250629_02921 Engine Control ModuleDesignation Equipment Installation location Task Address Word Data bus communication Engine Control Module J623 Always installed In the engine compartment next to the E-box Controlling the engine characteristic 01 Powertrain CAN bus user • Control modules (gas engine/diesel engine) have different plug connections • Immobilizer user • Vehicles with an anti-theft alarm have an anti-theft device (sheet metal cover with shear bolts) over the Engine Control ModuleSpecial featuresJ623629_030AirbagDesignation Equipment Installation location Tasks Address Word Data bus communication Special feature Airbag Control Module J234 Always installed On the center tunnel in front of the center console • Deployment of the airbags 15 • Powertrain CAN bus user • LIN master for Passenger Occupant Detection System Control Module J706 in vehicles for the North American RegionJ23422629_031 DSG transmissionDesignation Equipment Installation location Task Address Word Data bus communication DSG Transmission Mechatronic J743 Optional equipment for vehicles with double-clutch transmission: On the transmission Controlling the double-clutch transmission 02 Powertrain CAN bus userJ743629_032Selector lever sensorsDesignation Equipment Installation location Tasks Address Word Data bus communication Special feature Selector Lever Sensor System Control Module J587 For vehicles with DSG transmission: On the selector lever housing • Indication of the selector lever position • Indication of tiptronic commands 81 Powertrain CAN bus user The control module can only be replaced together with the selector leverJ587629_03323 Headlight range adjustmentDesignation Equipment Installation location Tasks Address Word Data bus communication Special feature Cornering Lamp and Headlamp Range Control Module J745 Always installed, different versions depending on type of headlights installed Behind the instrument panel, left-hand side • Dynamic headlight range adjustment • Controlling the light profiles 55 CAN-Extended bus user Connected to the power modules for the left and right headlights via a sub-bus systemJ431 / J745629_034Audi side assist (lane change warning system)Designation Equipment Installation location Tasks Address Word Data bus communication Special feature Lane Change Assistance Control Module J769 Lane Change Assistance Control Module 2 J770 Optional equipment, PR No.: 7Y1 • In the bumper, rear right (J769) • In the bumper, rear left (J770) • Monitoring the area behind and to the side of the vehicle • Activation of the warning lights in the door mirrors 3C • J769 (master) CAN-Extended bus user • J770 (slave) connected to J769 via a sub-bus system The control modules are mounted in the bumper cover. The system has to be calibrated after removal and installation.J769J77024629_035 Notes25 Exterior lightsHeadlightsFull LED headlights are now standard equipment for the 2016 TT. All functions, including low beam, high beam, daytime running lights, side lights, and turn signal indicator use LED technology.LED headlight629_040The bumper cover must first be removed when removing the headlights. They are connected to the body by adjusting elements which provide a means of adjustment to the other body parts. It is possible to adjust the headlights exactly with other body parts. The parts marked “Service” in the detailed description of the headlights on the following pages can be replaced individually in the event of damage.In the event of damage to the upper and inner headlight mounts, repair tabs can be attached to the headlight housing. Always refer to ElsaPro and ETKA for the proper workshop procedures and part numbers.26 LED headlight, PR No.: 8ITThe illustration shows the left headlight in the ECE1) versionDaytime running light/side light control unit "Service" LED headlight power module 1 "Service" (low beam and high beam) Headlight housingHeadlight power module "Service" (headlight range adjustment) All-weather light modulePlastic optical fiber with modular daytime running light/side lightLow beam module Turn signal module Design trim High beam module629_042Light functions Daytime running light Side light Low beam High beam All-weather light Turn signal light Sidemarker (not shown)Bulb used 10 LEDs with plastic optical fibers dimmed to approximately 10% when the side light function is active 11 LEDs 8 LEDs 3 LEDs 10 LEDs 2 LEDsPower 17 watts 30 watts 28 watts 10 watts 16 watts 1 wattActivation mechanism The day time running light/side light control module is activated directly by Vehicle Electrical System Control Module 1 J519. The control modules for the headlight power module and LED headlight power module 1 are connected to Cornering Lamp and Headlamp Range Control Module J745 via a CAN bus. J745 in turn receives its commands from the J519. The day time running light is switched off for the duration of a turn signaling cycle. The side light LEDs are used for the Coming Home/Leaving Home function.Adaptation for driving on the opposite side of the road It is not necessary to adapt the headlights. No further action is needed in order to meet the statutory requirements. Equipment The headlight washer system is integrated as standard into the LED headlight.Service With this headlight version, only the three outer control modules can be replaced. The headlight range adjustment servomotor (not shown) cannot be replaced individually.27 Headlight range adjustmentThe Audi TT always comes equipped with a dynamic headlight range adjustment system. Depending on the attitude and movement of the vehicle, Headlamp Beam Adjustment Motors (V48, V49) correct the headlight range of the headlights. However, the designation of the headlight range adjustment control unit, the number of ride height sensors as well as the transmission rate for activation of the headlight range adjustment servomotors differ according to headlight version. Schematic diagram of the headlight range adjustment system1) 2) in conjunction with LED headlights in vehicles with Audi magnetic rideThe Audi TT can be optionally equipped with Audi magnetic ride. These vehicles have four sensors for detecting the vehicle ride height. The signals from these senders are are sent to Electronic Damping Control Module J250 via discrete lines. J250 is a powertrain CAN bus user and relays information on vehicle ride height via CAN bus to the headlight range adjustment control unit (depends on headlight version installed).Left Rear Level Control System Sensor G761)Data Bus On Board Diagnostic Interface J533Cornering Lamp and Headlamp Range Control Module J7452)Headlamp Power Output Stages J667 / J6682)Left Rear Level Control System Sensor G762)Headlamp Beam Adjustment Motors V48 / V492)Cornering Lamp and Headlamp Range Control Module J7453)Headlamp Power Output Stages J667 / J6683)Left Rear Level Control System Sensor G763)Left Front Level Control System Sensor G783)Headlamp Beam Adjustment Motors V48 / V493)Electronic Damping Control Module J2504)Chassis CAN bus Extended CAN bus LIN bus Sub-bus systems Discrete lineLeft Rear Level Control System Sensor G762)Right Rear Level Control System Sensor G772)Left Front Level Control System Sensor G782)Right Front Level Control System Sensor G2892)629_04528 Tail lightsThe tail lights of the Audi TT use only LEDs. Two versions of tail lights are available: • Low version (used with Xenon headlights) (not available for the North American market) • High version (used with LED headlights) The tail light versions are geometrically identical. The only functional difference is the additional side marker for the SAE version.Brake light/ fog lightTail lightBack-up light629_046Sidemarker2)Turn signal lightBrake lightActivation mechanism The tail lights are activated by Vehicle Electrical System Control Module 1 J519. The tail light LEDs are used for the Coming Home/Leaving Home function.Service There are no serviceable parts for the tail lights. In the event of damage, the entire tail light unit must be replaced.2)SAE = for North American Region29 High-level brake light / license plate lightHigh-level brake lightThe high level brake light is integrated into the trunk lid below the rear spoiler. It has a total of 18 LEDs. The individual component parts of the high-level brake light cannot be replaced. If defective, the complete component must be replaced. The high-level brake light can be replaced after raising the rear spoiler.629_047License plate lightsThe license plate lights use LED technology irrespective of tail light version. Both lights are integrated into the trunk lid handle. Each has two LEDs. The license plate lights are activated by J519 and can be replaced individually.HandleBack-up camera629_048License plate lights30 Vehicle electronicsCar keyThe keys of the 2016 TT have been redesigned. The shape of the key and design of the buttons makes tactile identification and operation easier. Each new vehicle is supplied with three car keys. Two of these keys are fully functional remote control keys, while the third key is a wallet key. Each of the remote control keys houses a key to enable the valet functions. The wallet key can be used to open and close the mechanical locks on the vehicle. It is also possible to switch on the ignition and start the engine with this key. Because the wallet key does not have a battery, the emergency transponder coil must be used to turn on the ignition and start the engine. If the Audi TT is equipped with the optional advanced key (keyless entry system), the back of the remote control key is chrome-plated. The second remote control key is supplied in the standard design.removable key to enable valet functions629_049Audi TT car key in standard designKeyless starting systemThe keyless starting system is standard on the Audi TT. After pressing the Start button in the center console, the vehicle electronics check whether an authorized key is in the vehicle. If a key is in the vehicle, the ignition is switched on and the engine is started (the brake pedal must be pressed). A mechanical ignition lock is not required nor installed.To implement the keyless starting system, the following components are required in the vehicle: • J518 Access/Start Authorization Control Module. • E408 Access/Start Authorization Button. • R137 Access/Start Authorization Antenna in Luggage Compartment. • R139 Access/Start Authorization Antenna 2 in Vehicle Interior.R137R139 Convenience CAN busTerminal 30E4087.5 AAccess/Start Authorization Control Module J518629_05031 Terminal 15 power supplyAccess/Start Authorization Control Module J518 is the master controller for activation of Terminal 15. Access/ Start Authorization Button E408 provides the central signal input. J518 determines the current status of key contact and Terminals 15 and 50. The terminal states are indicated to all control modules via the various bus systems. Terminals 15 and 50 also exist as separate supply wires and are switched by relays. Terminal 15 Power Supply Relay J329 connects Terminal 30 power to the Terminal 15 supply wire when the ignition is switched on and disconnects them when the ignition is switched off. J329 is controlled by J519. To start the engine, a Terminal 15 supply wire (via J329) activates Starter Relays 1 and 2. This in turn connects a Terminal 50 line to the starter solenoid. For safety reasons, two series-connected starter relays are always installed. If one starter relay can no longer open its closed terminals after the engine starts, the second starter relay will open to break the starter motor circuit. The starter relays are activated and monitored for DTCs by Engine Control Module J623. The following pages discuss this process in detail.Terminal 30 Vehicle Electrical System Control Module 1 J519J329Terminal 15 Terminal 15 - 1 Terminal 15 - 2 Convenience CAN bus J533 Powertrain CAN bus J906Access/Start Authorization Control Module J518Key contactTerminal 50Engine Control Module J623 J907Terminal 50629_051J329 J533 J906 J907 Terminal 15 Power Supply Relay Data Bus On Board Diagnostic Interface Starter Relay 1 Starter Relay 232 Switching Terminal 15 Power Supply Relay J329There are three signal wires from J518 to J519: • Key contact. • Terminal 15 – 1. • Terminal 15 – 2. A signal voltage is applied to these three wires by J518 if J519 is required to activate Terminal 15 Power Supply Relay J329. J519 activates Terminal 15 Power Supply Relay J329 if at least two of the three signal wires is carrying a signal voltage. This configuration ensures that the vehicle can be started in the event of an open circuit in one of the three signal wires. Access/Start Authorization Control Module J518 also sends a terminal 15 request to J519 via the CAN bus but this has no effect on the actual switching of terminal 15; the signal wires are exclusively responsible for this.Convenience CAN busAccess/Start Authorization Control Module J518Key contact Terminal 15 - 1 Terminal 15 - 2Vehicle Electrical System Control Module 1 J519Terminal 30J329J329 Terminal 15 Power Supply RelayTerminal 15629_053Switching Starter Relays J906 and J907A terminal 50 signal wire leads directly to Engine Control Module J623 from J518. J518 applies a signal voltage to this wire if the engine is to be started. The ECM switches its two Starter Relays if this signal wire is live and all other requirements for starting the engine have been met. J518 also sends a terminal 50 request to J519 via the CAN bus. The ECM uses this information to validate the plausibility of the signal from J518.Terminal 15Convenience CAN busJ533Powertrain CAN bus J906Access/Start Authorization Control Module J518Terminal 50Engine Control Module J623 J907J533 J906 J907 Data Bus On Board Diagnostic Interface Starter Relay 1 Starter Relay 2Terminal 50629_05433 Advanced KeyThe Advanced key option is being offered on the Audi TT for the first time. The car key no longer has to be taken out of the driver's pocket in order to open both vehicle doors and the trunk lid. When the driver moves his hand into the door handle or the trunk lid handle, the advanced key uses radio signals to search for an authorized key. If the search is successful, the vehicle or trunk lid is unlocked. Keyless entry is possible on both the driver and front passenger doors. The following additional components are integrated into the advanced key for the keyless entry system: • G415 Driver Exterior Door Handle Touch Sensor. • G416 Front Passenger Exterior Door Handle Touch Sensor. • R134 Driver Access/Start System Antenna. • R135 Front Passenger Access/Start System Antenna. • R136 Access/Start System Antenna in Bumper.Terminal 30 E408 R134 R135 R136 R137 R1397.5 AAccess/Start Authorization Control Module J518Wake-up signalConvenience CAN busG415G416 R47Data Bus On Board Diagnostic Interface J519629_055Implementation of keyless entry and start systems at AudiThere are two different versions of the keyless entry system for Audi models. The systems differ from one another in regard to system supplier and the internal system processes, however not from the customer's point of view. The systems in the ‘B’ series vehicles onwards are suppied by Marquardt, while the systems in the Audi A3 and Audi TT are suppied by Hella. The keyless entry and start system was first introduced in the Audi A8 (D3) in 2003. The system was subsequently described in several Self-Study Programs. All previous system descriptions refer to the Marquardt system because this was the only system in the Audi model range until now. This eSelf-Study program gives a detailed description of the Hella system offered in the 2016 Audi TT. The following system processes are described: • Turning on the ignition with the start button. • Turning on the ignition with the emergency transponder coil. • Starting the engine with the start button. • Unlocking the vehicle via the sensor in the driver's door handle. • Unlocking the trunk lid using the Softtouch function.34 Notes35 System processes in the keyless start systemTurning on the ignition (not starting the engine)Initial situation: • The vehicle is equipped with an automatic transmission. • An authorized key is located inside the vehicle. • The brake pedal is not pressed when the start button is pressed. • The CAN bus and Vehicle Electrical System Control Module 1 are active.E408Terminal 30R137R1397.5 AAccess/Start Authorization Control Module J518Key contactTerminal 15 - 1Terminal 15 - 2Wake-up signalJ764Convenience CAN busJ285Vehicle Electrical System Control Module 1 J519R47Terminal 30J329 D2Terminal 15D2 Anti-theft Immobilizer Reader Module629_056E408 Access/Start Authorization Button J285 J329 J764 R47 Instrument Cluster Control Module Terminal 15 Power Supply Relay Electronic Steering Column Lock Control Module Central Locking and Anti-theft Alarm System AntennaR137 Access/Start System Antenna in Luggage Compartment R139 Access/Start System Antenna 2 in Vehicle Interior36 The system process step by step:1. Access/Start Authorization Button E408 is pressed. 2. This is detected by J518. 3. J518 instructs J764 to unlock the steering column via the Convenience CAN bus. 4. J518 instructs Instrument Cluster Control Module J285 via the Convenience CAN bus to enable the terminals. 5. J285, in turn, instructs J518 to search for an authorized key. 6. J518 initiates a key search by activating antennas R137 and R139. 7. An authorized key receives the signals sent by both interior antennas and responds by giving its key identification number. 8. J519 receives the response from the key via Central Locking and Anti-theft Alarm System Antenna R47. 9. J519 indicates the reception of a key response to J285 via the Convenience CAN bus. 10. J285 sends key authentication data to J518 via the Convenience CAN bus. 11. J518 activates interior antennas R137 and R139 once again to transfer authentication data and measurement signals. 12. The key measures the field strengths of the measurement signals. Taking the measured field strengths as a basis, the key determines whether it is located inside the vehicle or not. In addition, the key calculates an appropriate key response based on the authentication data received. 13. The key sends a radio response if located inside the vehicle, and no response if not located inside the vehicle.14. After receiving a key response, J519 transmits the response to J285. 15. Taking the key response as a basis, J285 checks whether the response originates from an authorized key. 16. If the check is successful, J285 notifies J764 via the Convenience CAN bus. 17. If all the requirements for unlocking the steering column are met, J764 unlocks the steering column. 18. The successful unlocking of the steering column is indicated to J518 and J285 via the Convenience CAN bus. 19. J285 sends an enabling signal for the terminals to J518. 20. J518 receives this information and checks whether all the requirements for switching on terminal 15 have been met. 21. If all the requirements have been met, the three signal lines (key contact, terminal 15-1 and terminal 15-2) are switched by J518. 22. If J519 measures a high enough voltage level in at least two of the three signal lines, it switches relay J329. The terminal 15 supply voltage will then be available to the connected electrical loads. 23. After switching the relay, J519 changes the status of terminal 15 from "off" to "on" and places this information on the CAN bus.37 Turning on the ignition via the emergency transponder coil (not engine starting)Initial situation: • The vehicle is equipped with an automatic transmission. • The batteries in the remote control key are so weak, it is not possible to communicate with the vehicle. • The CAN bus and Vehicle Electrical System Control Module 1 are active. • The brake pedal is not pressed when the driver presses the start button.E408Terminal 30R137R1397.5 AAccess/Start Authorization Control Module J518Key contactTerminal 15 - 1Terminal 15 - 2Wake-up signalJ764Convenience CAN busJ285Vehicle Electrical System Control Module 1 J519R47Terminal 30J329 D2Terminal 15D2 Anti-theft Immobilizer Reader Module629_056E408 Access/Start Authorization Button J285 J329 J764 R47 Instrument Cluster Control Module Terminal 15 Power Supply Relay Electronic Steering Column Lock Control Module Central Locking and Anti-theft Alarm System AntennaR137 Access/Start System Antenna in Luggage Compartment R139 Access/Start System Antenna 2 in Vehicle Interior38 The system process step by step:1. Access/Start Authorization Button E408 is pressed. 2. This detected by Access/Start Authorization Control Module J518. 3. J518 instructs J764 to unlock the steering column via the Convenience CAN bus. 4. J518 then instructs Instrument Cluster Control Module J285 to enable the terminals via the Convenience CAN bus. 5. J285, in turn, instructs J518 to search for an authorized key. 6. J518 then initiates a key search by activating interior antennas R137 and R139. 7. Because the battery of the authorized key is too weak, this key can neither receive the message nor send a radio response. 8. J285 does not receive a key response from J519 via the Convenience CAN bus within the given time period. 9. After this, J285 again instructs J518 to search for an authorized key. 10. J518 again activates its two interior antennas, R137 and R139. 11. J285 again does not receive a key response from J519 via the convenience CAN within the given time period. 12. J285 then displays a message to prompt the driver to hold the key in the position indicated inside the vehicle. 13. J285 energizes Anti-theft Immobilizer Reader Coil D2 for a defined period of time.14. The driver holds the car key in the position indicated. 15. The coil supplies the key with sufficient power and exchanges data with it. 16. J285 receives this data and verifies it. 17. If the check is successful, J285 notifies J764 via the Convenience CAN bus. 18. If all other requirements have been met, J764 unlocks the steering column. 19. The successful unlocking of the steering column is indicated to J518 and J285 via the Convenience CAN bus. 20. J285 sends an enabling signal for the terminals to J518. 21. J518 receives this information and checks whether all the requirements for switching on terminal 15 have been met. 22. If all the requirements have been met, the three signal lines (key contact, terminal 15-1 and terminal 15-2) are switched by J518. 23. If J519 measures a high enough voltage level in at least two of the three discrete terminal lines, it switches Terminal 15 Power Supply Relay J329. The terminal 15 supply voltage will then be available to the connected electrical loads. 24. After switching the relay, J519 changes the status of terminal 15 from "off" to "on" and places this information on the CAN bus.39 Starting the engine with the ignition onInitial situation: • The vehicle's ignition is on. • The vehicle has an automatic transmission. • The brake pedal is pressed. • An authorized key is located inside the vehicle.E408Terminal 30R137R1397.5 AAccess/Start Authorization Control Module J518Terminal 15Terminal 50 J906J533 Convenience CAN bus Powertrain CAN bus R47J907Engine Control Module J623J285Vehicle Electrical System Control Module 1 J519Terminal 50D2629_057D2 Anti-theft Immobilizer Reader CoilE408 Access/Start Authorization Button J285 J533 J906 J907 R47 Instrument Cluster Control Module Data Bus On Board Diagnostic Interface Starter Relay 1 Starter Relay 2 Central Locking and Anti-theft Alarm System AntennaR137 Access/Start System Antenna in Luggage Compartment R139 Access/Start System Antenna 2 in Vehicle Interior40 The system process step by step:1. Access/Start Authorization Button E408 is pressed. 2. This is detected by Access/Start Authorization Control Module J518. The module knows the driver wants to start the engine because the brake pedal is depressed. 3. J518 applies a voltage to the “terminal 50” signal line leading to Engine Control Module J623. 4. It also changes the "terminal 50" bit request of the corresponding CAN bus message from 0 to 1. 5. J518 requests the enabling signal for the terminals from Instrument Cluster Control Module J285. 6. J285, in turn, instructs J518 to search for an authorized key. 7. J518 then initiates a key search by activating two interior antennas R137 and R139. 8. An authorized vehicle key in side the vehicle receives the signals sent by both interior antennas and responds by giving its key identification number. 9. J519 receives the response from the key through antenna R147. 10. J519 indicates the reception of a key response to J285 via the Convenience CAN bus.11. J285 sends key authentication data to J518 via the Convenience CAN bus. 12. J518 activates interior antennas R137 and R139 once again in order to transfer authentication data and measurement signals. 13. The key measures the field strengths of the measurement signals. Taking the measured field strengths as a basis, the key determines whether it is located inside the vehicle or not. 14. In addition, the key calculates an appropriate key response based on the authentication data received. 15. If the key is located inside the vehicle, its sends a key response. 16. J519 indicates the reception of a key response J285 via the Convenience CAN bus. 17. J285 evaluates the key response with regard to the immobilizer. If this evaluation and all other checks are successful, J285 issues an engine enabling signal via the CAN bus. 18. J623 receives the engine start enabling signal. Voltage is already present in the terminal 50 signal line from J518. The ECM then switches its two terminal 50 relays. 19. The starter is subsequently energized and the engine starting cycle is initiated.41 System processes in the keyless entry system (Advanced key)Keyless unlocking of the vehicle at the driver's doorInitial situation: • There is an authorized car key outside the vehicle within a radius of 5.0 ft (1.5 m) of the driver's side door handle. • The vehicle is parked and locked.Terminal 30 E408 R134 R135 R136 R137 R1397.5 AAccess/Start Authorization Control Module J518Wake-up signalConvenience CAN busG415 R47G416 Vehicle Electrical System Control Module 1 J519 Driver Door Control Module J386 Front Passenger Door Control Module J387629_058F248E408 Access/Start Authorization Button F248 Rear Lid Lock Cylinder Unlock Button G415 Driver Exterior Door Handle Touch Sensor G416 Front Passenger Exterior Door Handle Touch Sensor R47 Central Locking and Anti-theft Alarm system AntennaR134 Driver Access/Start System Antenna R135 Front Passenger Access/Start System Antenna R136 Access/Start System Antenna in Rear Bumper R137 Access/Start System Antenna in Luggage Compartment R139 Access/Start System Antenna 2 in Vehicle Interior42 The system process step by step:1. The customer grips the door handle of the driver's door. 2. The request to open is detected by J518 through Driver Exterior Door Handle Touch Sensor. 3. J518 then activates antenna R134 on the driver's side, and a key search begins. 4. J518 wakes up Vehicle Electrical System Control Module 1 J519 via a signal line. 5. An authorized car key which receives this antenna signal then responds by giving its key identification number as feedback. 6. J519 receives a key response through the antenna R47. It subsequently wakes up the convenience CAN bus. 7. J519 informs that it has received a key response. 8. J518 re-activates antenna R134, followed by interior antennas R137 and R139. 9. The key receives the antenna signals and measures their field strengths.10. Based on the measured field strengths, the key can decide whether it is in a position which allows the vehicle to be unlocked. 11. If the key arrives at a positive result, it sends a key response to J519. In the event of a negative result, no response is sent. 12. J519 receives the response from the key through the central locking antenna R47. 13. If more than one authorized key provides feedback, J519 assigns a higher priority to one of the keys and proceeds with this key only. 14. The key response contains additional information based on which J519 can verify whether the response actually originates from an authorized car key. 15. If this is the case and if all other requirements for unlocking have been met, the unlocking command is placed on the CAN bus. 16. The door control modules unlock the vehicle doors, and the handle in the trunk lid F248 (Softtouch) is enabled.43 Keyless trunk lid openingInitial situation: • There is an authorized car key outside the vehicle within a radius of 5.0 ft (1.5 m) of the trunk lid handle. • The vehicle is parked and locked.Terminal 30 E408 R134 R135 R136 R137 R1397.5 AAccess/Start Authorization Control Module J518Wake-up signalConvenience CAN busG415 R47G416 Vehicle Electrical System Control Module 1 J519 Driver Door Control Module J386 Front Passenger Door Control Module J387629_058F248The system process step by step: 1. The customer reaches into the handle in the trunk lid. 2. The actuation of Rear Lid Lock Cylinder Unlock Button F248 (Softtouch) is detected by J519. 3. Vehicle Electrical System Control Module 1 J519 wakes up the Convenience CAN bus. 4. J519 instructs Access/Start Authorization Control Module J518 via the Convenience CAN bus to search for a key at the rear of the vehicle. 5. J518 subsequently activates Access/Start System Antenna in Rear Bumper R136. 6. An authorized car key which receives this signal then responds by giving its key identification number as feedback. 7. J519 receives the response from the key through the Central Locking and Anti-theft Alarm System Antenna R47. 8. J519 indicates to J518 via the Convenience CAN bus that an authorized key has responded.449. J518 re-activates antenna R136, followed by interior antennas R137 and R139. 10. The key receives the antenna signals and measures their field strengths. 11. Based on the measured field strengths, the key can decide whether it is in a position which allows the trunk lid to be unlocked. 12. If the key arrives at a positive result, it sends a key response. In the event of a negative result, no response is sent. 13. J519 receives and evaluates this information. 14. This key response contains additional information based on which J519 can verify whether the response actually originates from an authorized car key. 15. If all the requirements for unlocking the trunk lid have been met, J519 activates the trunk lid lock, and the trunk lid open. ImmobilizerA fifth generation immobilizer system is used on the 2016 TT. It is the same as the system used on the 2015 A3 and is diagnosed in the same manner.Convenience CAN busData Bus On Board Diagnostic Interface J533Instrument Cluster Control Module J285Electronic Steering Column Lock Control Module J764Powertrain CAN busEngine Control Module J623Transmission Control Module J217Car key629_059Immobilizer master control module: • Instrument Cluster Control Module J285.Other immobilizer system participants: • • • • All car keys. Engine Control Module J623. Electronic Steering Column Lock Control Module J764. Transmission Control Module J217.!Note Please note the information on installation of Electronic Steering Column Lock Control Module J764 on the following page.45 Electronic Steering Column Lock Control Module J764At launch, all TT models will come equipped with Electronic Steering Column Lock Control Module J764. It is planned to eliminate this control module in models with automatic transmissions in some markets. Always consult ElsaPro and ETKA for the latest information when working on this system.Installation location of J764Electronic Steering Column Lock Control Module J764629_060Steering column locking bolt Steering column of the Audi TT629_061Comparing the steering column locking systems of the 2016 TT and the 2015 Audi A3 reveals the following commonalities and differences:Commonalities: • J764 is integrated with the immoblizer system. • J764 locks and unlocks the steering column. • J764 is connected to the convenience CAN bus.Differences: • On the Audi A3, installation of the electronic steering column lock is coupled to the optional advanced key. It comes installed in 100% of Audi TT models. • On the A3, J764 reads the signal from Access/Start Authorization Button E408. On the 2016 TT this task is performed by Access/Start Authorization Control Module J518. • On the A3, J764 assumes the master function for terminal control. On the 2016 TT, this task is performed by Access/Start Authorization Control Module J518. • On the A3, five additional signal lines lead to J764. On the 2016 TT, no signal lines lead to J764.46 Electrical rear spoilerThe 2016 TT has an electrically operated rear spoiler as standard equipment. There are two differences between the way in which the rear spoiler operates in the 2016 Audi TT and in the predecessor model.1. The task of controlling the rear spoiler has been transferred to Vehicle Electrical System Control Module 1 J519. It was controlled by Comfort System Central Control Module J393 on the predecessor model.2. Two Hall sensors are used to detect the position of the rear spoiler in the Audi TT. Two micro-switches were used for this purpose in the predecessor model. The two micro-switches only indicated when a limit position had been reached. An issue with