TECHNICAL DOCUMENTATION
SSP 970243 – The 2015 Audi A3 Onboard Power Supply and Networking Systems

This PDF is currently unavailable.
Read document text
eSelf Study Program 970243The 2015 Audi A3 Onboard Power Supply and Networking Systems• The Self Study Programme teaches a basic knowledge of the design and functions of new models, new automotive components or new technologies. It is not a Repair Manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. For further information about maintenance and repair work, always refer to the current technical literature.NoteReference2Audi of America, LLC Service Training Created in the U.S.A. Created 11/2013 Course Number 970243 ©2013 Audi of America, LLC All rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC. Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.Revision 1: 11/20133ContentsPower supply....................................................................................... 6Battery ....................................................................................................................................................6 Battery housing .....................................................................................................................................6 Fuses, relays and jump start terminal .................................................................................................7Networking.......................................................................................... 9Installation locations of control modules ...........................................................................................9 Topology ...............................................................................................................................................11 Overview of bus systems .....................................................................................................................13 New features of the bus system ........................................................................................................13 Optical data bus system MOST150 ....................................................................................................14 Special tool VAS 6778 .........................................................................................................................14Control modules................................................................................15Brief descriptions .................................................................................................................................15Exterior lighting................................................................................29Light switch ..........................................................................................................................................29 Headlights ............................................................................................................................................30 Headlight range control ......................................................................................................................32 Tail lights ..............................................................................................................................................34 High-mounted brake light ..................................................................................................................35 License lights .......................................................................................................................................35eSelf Study Programs........................................................................36 Knowledge Assessment....................................................................384This eSelf Study Program teaches a basic knowledge of the design and functions of new models, new automotive components or technologies. It is not a Repair Manual! All values given are intended as a guideline only. For maintenance and repair work, always refer to the current technical literature.NoteReferencePower supplyBatteryThe battery for the 2015 A3 is located in the engine compartment and is protected by a battery box. Battery size and type are dependent on engine version, trim and country specification. Standard batteries, EFB batteries and AGM batteries are used. In general, vehicles with gasoline engines are equipped with an EFB battery, while diesel engine equipped vehicles us an AGM battery.EFBAn EFB (Enhanced Flooded Battery) can be regarded as a heavy-duty wet-cell battery. The positive plate inside the battery is coated with an additional polyester mesh. This provides additional retention for the active battery material. The deep-cycle resistance is higher than that of conventional batteries. An EFB is charged in exactly the same way as a conventional battery.AGM batteryIn AGM (Absorbent Glass Mat) batteries, the battery electrolyte is held within a microporous glass matting. In addition to having higher deep-cycle resistance than an EFB battery, the AGM battery is noted for its leak-proof construction. Special charging procedures may be required for an AGM battery.The following batteries are used in the 2015 Audi A3 dependent on engine type:Standard batteries • • • • • 44 Ah/220 A 51 Ah/280 A 60 Ah/280 A 61 Ah/330 A 72 Ah/380 AEFB • 59 Ah/280 A • 69 Ah/360 AAGM batteries • 58 Ah/340 A • 68 Ah/380 ABattery housingThere are three different lengths of battery retaining points to accommodate the different battery sizes.Hole 1 2 3 Battery housing length 8.3 in (212 mm) 9.7 in (247 mm) 10.9 in (278 mm)Hole 1 Hole 2Hole 3610_0086Fuses, relays and jump start terminalThe positive terminal on the battery and the jump start terminal on the engine compartment bulkhead are used for charging the battery and jump starting.Jump start terminal on the engine bulkheadBattery ground terminal and Battery Monitoring Control Module J367Battery positiveBattery A Fuse rail in the E-box with fuses identified by “SA” in the Wiring Diagrams.E-box with fuses and relays identified by “SB” in the Wiring Diagrams.610_073Fuse holder and relay carrier under the instrument panel with the designation “SC” in the Wiring DiagramsIn addition to standard fuses, the space-saving mini-fuses and circuit breakers (thermal fuses), a new J-Case fuse is being used. As with other fuses, they are identifiable by their color.Fuse rating 20 A 25 A 30 A 40 A 50 A 60 AColor blue white pink green red yellowJ-Case fuses610_072A new gripping tool is used to remove and install the J-Case fuse. It is stored in the cover of the E-box in the engine compartment.Gripping tool for J-Case fuses610_0717Notes8NetworkingInstallation locations of control modulesSome of the control modules shown in the overview may be optional and/or country specific equipment. Always refer to the current service literature for complete details about control module locations as well as instructions for their removal and installation.J387J668 J104J794J250J500R242 J428 J685 J234 J255 E380 J587J431 J745 J743J518 J533 J527 J764 J525J285J623J667J519 J3869Key:E380 Multimedia System Control Head J104 J234 J250 J255 J285 J386 J387 J428 J431 J492 J500 J518 J519 J525 J527 ABS/ESP Control Module Airbag Control Module Electronic Damping Control Module Climatronic Control Module Instrument Cluster Control Module Driver Door Control Module Front Passenger Door Control Module Distance Regulation Control Module Headlamp Range Control Module All Wheel Drive Control Module Power Steering Control Module Access/Start Authorization Control Module Vehicle Electrical System Control Module 1 Digital Sound System Control Module* Steering Column Electronics Control Module J533 J587 J623 J667 J668 J685 J743 J745 J764 J769 J770 J772 J794 J926 J927 Data Bus On Board Diagnostic Interface Selector Lever Sensor System Control Module Engine Control Module Left Headlamp Power Output Stage Right Headlamp Power Output Stage Front Information Display Control Head DSG Transmission Mechatronic Cornering Lamp and Headlamp Range Control Module Electronic Steering Column Lock Control Module Lane Change Assistance Control Module Lane Change Assistance Control Module 2 Rearview Camera System Control Module Information Electronics Control Module 1 Driver Side Rear Door Control Module Passenger Side Rear Door Control ModuleR242 Driver Assistance Systems Front CameraJ927 J772 J769J492J770 J926*Only on vehicles equipped with the Bang & Olufsen sound system option 9VS.625_09710TopologyThe topology shows all control modules with connectivity to the data bus system. Some of the control modules shown here are optional, country-specific equipment, or will be introduced at a later date. Be aware that all the modules shown will not be installed on every vehicle.Light switch E1 Headlight power module, left J667Power Sunroof Control Module J245Wiper motor control unit J400Headlight power module, right J668Anti-theft Alarm System Sensor G578Rain/Light Recognition Sensor G397Humidity sensor G355Power output module for left LED headlightAlarm horn H12Vehicle Electrical System Control Module J519 Instrument Cluster Control Module J285Power output module for right LED headlightLane Change Assistance Control Module 2 J770Steering Column Electronics Control Module J527 Driver Side Rear Door Control Module J926Data Link Connector Multifunction steering wheel control unit J453Driver Door Control Module J386Passenger Side Rear Door Control Module J927Front Passenger Door Control Module J387Data Bus Onboard Diagnostic Interface J533Nox Sensor Control Module J583* Engine Control Module J623Access/Start Authorization Control Module J518 Electrical Steering Column Lock Control Module J764Nox Sensor Control Module 2 J881*Passenger Occupant Detection System Control Module J706 Left Front Seat Belt Tensioner Control Module J854 Right Front Seat Belt Tensioner Control Module J855Airbag Control Module J234Climatronic Control Module J255DSG Transmission Mechatronic J743Selector Lever Sensor System Control Module J587 Fresh Air Blower Control Module J126 Refrigerant Circuit Pressure Sensor G805 Humidity Sensor in Fresh Air Intake Duct G657 Air quality sensor G238*2.0L TDI engine only11For example, Cornering Lamp and Headlight Range Control Module J745 would never be installed on the same vehicle as Headlamp Range Control Module J431.Headlamp Range Control Module J431Cornering Lamp and Headlight Range Control Module J745Multimedia System Control Head E380Lane Change Assistance Control Module J769 Driver Assistance Systems Front Camera J842 Distance Regulation Control Module J428Front Information Display Control Head J685Digital Sound System Control Module J525Information Electronics Control Module 1 J794 ABS/ESP Control Module J104 Battery Monitoring Control Module J367Power Steering Control Module J500Alternator CAll Wheel Drive Control Module J492Rearview Camera System Control Module J772Electronic Damping Control Module J250610_001_pkdKey: Powertrain CAN bus Convenience CAN bus Extended CAN bus Infotainment CAN bus Diagnostics CAN bus Suspension CAN bus LIN bus Sub-bus systems MOST bus12Overview of bus systemsBus system Powertrain CAN bus Convenience CAN bus Extended CAN bus Infotainment CAN bus Suspension CAN bus Diagnostics CAN bus MOST bus Cable color Configuration Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Electrical two-wire bus system Optical bus system Max. data transfer rate 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 150 Mbit/s Characteristic Not single-wire capable Not single-wire capable Not single-wire capable Not single-wire capable Not single-wire capable Not single-wire capable Ring structure: an open circuit leads to total system failure Single-wire capable Not single-wire capableLIN bus Sub-bus system (private bus)Electrical single-wire bus system Electrical two-wire bus system20 kbit/s 500 kbit/sNew features of the bus system• The Convenience CAN and Infotainment CAN are highspeed systems on the 2015 A3. • New MOST bus – MOST150 (MOST150 has replaced MOST50). • Instrument Cluster Control Module J285 is a Convenience CAN participant. • Data Bus On Board Diagnostic Interface J533 is the master of LIN slave Multifunction Steering Wheel Control Module J453. • J533 is not a MOST bus participant. • Information Electronics Control Module 1 J794 is the system and diagnostic manager for the MOST 150 bus. • Information Electronics Control Module 1 J794 is connected to the MMI operating unit and display through a sub-bus system.13Optical data bus system MOST150HistoryThis data bus system is named after the "Media Oriented Systems Transport (MOST) Cooperation". This group is made up of various automobile manufacturers, their components suppliers and software companies, who joined forces to create a standardized high-speed data transfer system. It was used for the first time in the 2004 Audi A8. The term “Media Oriented Systems Transport” denotes a network that unlike the CAN data bus, sends address oriented messages to specific users. This technology is used by Audi to transfer data within the Infotainment system.MOST150The MOST150 bus is used for the first time by Audi in the new 2015 A3. It is six times faster than MOST25 and necessitated some modifications to MOST components. For instance, the transmitter and receiver units – Fiber Optical Transmitters (FOT) – had to be adapted. Other components, such as the optical connectors, the fiber optics and the electrical connections of the control units, are identical to those of the MOST25.System managerTwo control modules participate on the MOST150 bus in the 2015 A3: • Information Electronics Control Module 1 J794 • Digital Sound System Control Module J525 In the 2015 A3, Information Electronics Control Module 1 J794 functions as the system manager and diagnostic manager for the MOST150 system. The was previously done by Data Bus On Board Diagnostic Interface J533.Digital Sound System Control Module J525Information Electronics Control Module 1 J794610_069Special tool VAS 6778DiagnosticsThe ring break diagnosis procedure is identical to that of the previous MOST bus system. However, the Address Word for the 2015 A3 is 5F. Even though the ring break diagnosis procedure remains unchanged, a new special tool - VAS 6778 - must be used if there is a DTC in the optical system. This is due to the increased data transmission speeds.610_07414Control modulesBrief descriptionsVehicle electricsDesignation Equipment Installation position Tasks Vehicle Electrical System Control Module J519 Always installed Under the left side of the instrument panel • • • • • • Central locking master Exterior light master Interior light master Antitheft alarm master Activation of various relays Activation of various convenience components: • Seat heaters • Heated windshield washer nozzles • Windshield washer pump • Headlight washer system pump • Reading various switch and button positions • Reading various sensor values 09 • Convenience CAN bus participant • J519 is the LIN master for: • LIN 1 – Light Switch 1, Wiper Motor Control Module J400, Rain/Light Recognition Sensor G397, Humidity Sensor G355 • LIN 2 – Alarm Horn H12 • LIN 3 – Power Sunroof Control Module J245, Anti-theft Alarm System Sensor G578 LIN 1 is distributed to two pins on J519. J400 is connected to pin B30. E1, G397 and G355 – are connected to pin C28. This means that the control modules connected to pin C28 are also affected in the event of a short circuit to positive or negative at pin B30.Address Word Data bus communicationSpecial featureJ519610_009Reference For a detailed description of Vehicle Electrical System Control Module J519, please see eSelf-Study Program 970343, The 2015 Audi A3 Vehicle Electronics and Drivers Assistance Systems.15GatewayDesignation Equipment Installation position Tasks Data Bus On Board Diagnostic Interface J533 (Gateway) Always installed Under the left side of the instrument panel • • • • 19 • All CAN bus system participant • LIN master of Battery Monitoring Control Module J367 and alternator • LIN master of multifunction Multifunction Steering Wheel Control Module J453 Not a MOST bus user Networking gateway Diagnostic master (with the exception of MOST150) Energy management system control Master for multifunction steering wheel / optional equipmentAddress Word Data bus communicationSpecial featureJ533610_010Instrument cluster / DISDesignation Equipment Instrument Cluster Control Module J285 Always installed Versions: • Monochrome DIS with onboard computer, PR No.: 9S5 • Color DIS with onboard computer, PR No.: 9S6 Instrument Panel • Display of information relevant to the driver • Immobililzer master 17 Convenience CAN bus participant Convenience CAN participant for first time on an Audi modelInstallation position Tasks Address Word Data bus communication Special featureJ285 (European version shown)610_01116Steering column electronicsDesignation Equipment Installation position Tasks Steering Column Electronics Control Module J527 Always installed On the steering column • Connects the steering column stock and the electrical components in the steering wheel to the vehicle electronics • Terminal management master for vehicles without advanced key 16 Convenience CAN bus participant Transfers the LIN signals from J533 (Gateway) to Multifunction Steering Wheel Control Module J453 in models equipped with a multifunction steering wheelAddress Word Data bus communication Special featureJ527610_012Heating / air conditioningDesignation Equipment Installation position Tasks A/C Control Module J301 Climatronic Control Module J255 • Air conditioning system, PR No.: KH6 • Climatronic, PR No.: 9AK In center of instrument panel Controlling: • Temperature • Blower • Air distribution 08 • Convenience CAN bus participant • J301 is also the LIN master of Refrigerant Circuit Pressure Sensor G805 • J255 is also the LIN master of Air Quality Sensor G238 and Humidity Sensor in Fresh Air Intake Duct G657 All LIN slaves are connected to a LIN output.J301 J255Address Word Data bus communicationSpecial feature610_015610_01617Door electronics, driver sideDesignation Equipment Installation position Task Address Word Data bus communication Special features Driver Door Control Module J386 Always installed In the driver's door Controlling the electrical and electronic components in and on the driver's door 42 • Convenience CAN bus participant • In 5-door models it is connected to Driver Side Rear Door Control Module J926 • J386 acts as the substitute master for the central locking system in the event of failure of Vehicle Electrical System Control Module J519 • Activates the side marker lights in the driver's door mirrorJ386610_017Front passenger side door electronicsDesignation Equipment Installation position Task Address Word Data bus communication Special feature Front Passenger Door Control Module J387 Always installed In the front passenger's door Controlling the electrical and electronic components in and on the front passenger's door 52 • Convenience CAN bus participant • In 5-door models it is connected to Passenger Side Rear Door Control Module J927 via a LIN line Activates the side marker lights in the front passenger door mirrorJ387610_01818Advanced key / keyless entry and start authorizationDesignation Equipment Installation position Tasks Address Word Data bus communication Special feature Access/Start Authorization Control Module J518 Optional equipment, PR No.: 4F2 Under the instrument panel • Reads signals from both capacitive sensors • Activation of the entry and start authorization antennas B7 Convenience CAN bus participant External antennas connected to J518 are not installed in the doors but rather on the vehicle underbody near the ‘B’ pillars.J518610_019Electrical steering column lockDesignation Equipment Installation position Tasks Address Word Data bus communication Special features Electronic Steering Column Lock Control Module J764 Optional advanced key, PR No.: 4I3 On the steering column • Locking and unlocking the steering column • Terminal management master 2B Convenience CAN bus participant • Can be replaced separately from the steering column • Immobilizer participant • Reads signals from the entry and start authorization buttonJ764610_02019Back-up cameraDesignation Equipment Rearview Camera System Control Module J772 Optional equipment Version: • Parking aid (front/rear) with back-up camera, PR No.: 7X2+KA2 Behind the side trim on the right-hand side of the luggage compartment • Converting and processing the raw images captured by the rearview camera • Transferring the processed images to Information Electronics Control Module J794 6C Convenience CAN bus participant • Video connections are mechanically encoded • Only two of the three connections are usedInstallation position Tasks Address Word Data bus communication Special featuresJ772 Back-up camera connectionUnusedElectrical Video output connection610_025Audi adaptive cruise control Audi pre sense frontDesignation Equipment Distance Regulation Control Module J428 Optional equipment for vehicles with: • Stronic, PR No.: 8T3 • pre sense front, PR No.: 7W2 Behind center of front grille below license plate mount • Radar scanning of traffic • Controlling speed and distance 13 CAN-Extended bus participant Independent braking to a standstill behind a vehicle driving ahead and independent restarting (ACC Stop & Go)Installation position Tasks Address Word Data bus communication Special featureJ428610_04320InfotainmentDesignation Equipment Information Electronics Control Module 1 J794 Versions: • MMI Radio, PR No.: I8B • MMI Navigation plus, PR No.: I8F, 7UG In the glove compartment Controlling the infotainment systems 5F Infotainment CAN bus participant J794 is the system manager as well as the ring break diagnostics master for the MOST busInstallation position Task Address Word Data bus communication Special featuresJ794 (MMI navigation plus with Audi connect module shown)610_026Sound amplifier*Designation Equipment Installation position Task Address Word Data bus communication Digital sound package control unit J525 Installed on all vehicles Bang & Olufsen sound system Under the driver’s seat Activation of the speakers 47 MOST bus participantJ525610_027*The sound amplifier for vehicles equipped with the Audi sound system is integrated with Information Electronics Control Module 1 J794.21Electronic Stabilization Program ESPDesignation Equipment Installation position Tasks ABS/ESP Control Module J104 Always installed • On the right side of the engine compartment near the bulkhead • • • • • • • 03 Suspension CAN bus participant • The control module can be replaced separately from the valve block using ESD protective mat VAS 6613 • The electro-mechanical parking brake is integrated in the ABS control module. Address Word 53 for electro-mechanical parking brake has been deleted. Anti lock braking system ABS Electronic Stabilization Program ESP Traction Control System TCS Electronic Differential Lock EDL Electronic transverse lock Post collision brake assist Electro-mechanical parking brake EPBAddress Word Data bus communication Special featuresJ104 Hydraulic unit610_029Power steeringDesignation Equipment Installation position Tasks Power Steering Control Module J500 Always installed Connected to the steering gear • • • • 44 Suspension CAN bus participant • Control module with power steering motor and Steering Angle Sensor G85 can only be replaced together with the steering gear • G85 has no separate data bus connections; data is transferred via Power Steering Control Module J500 Power steering Servotronic – speed-dependent power steering Corrective steering intervention in combination with Audi active lane assist Corrective steering intervention in combination with ESPAddress Word Data bus communication Special featuresJ500610_030Reference For detailed descriptions of the suspension components refer to eSelf-Study Program 960143, The 2015 Audi A3 Running Gear and Suspension.22All-wheel driveDesignation Equipment Installation position Task Address Word Data bus communication Special feature All Wheel Drive Control Module J492 Standard equipment with quattro drive train Connected externally to the rear axle gear Control of the Haldex coupling according to the driving situation 22 Suspension CAN bus participant The control can be replaced separately without removing the rear axle gearJ492610_031Parking aidDesignation Equipment Parallel Parking Assistance Control Module J791 Optional equipment Version: • Parking aid plus, PR No.: 7X2 Behind instrument panel on left side Reads signal from ultrasound sensors and issues audible or visual warnings 76 Suspension CAN bus participant Address Word changed from 10 to 76 . Will only control front and rear acoustic sensors on vehicles for the North American region.Installation position Tasks Address Word Data bus communication Special featureJ791610_03223Audi magnetic rideDesignation Equipment Installation position Task Address Word Data bus communication Electronic Damping Control Module J250 Optional equipment, PR No.: 2H7 Under the right-hand front seat Adaptation of the damping characteristic 14 Suspension CAN bus participantJ250610_033Engine controlDesignation Equipment Installation position Task Address Word Data bus communication Special features Engine Control Module J623 Always installed In the engine compartment between battery and E-box Controlling the engine operating characteristics 01 Powertrain CAN bus participant • Engine Control Modules have differing terminating connectors depending on engine version installed • Immobilizer participant • Vehicles with an anti-theft alarm have an anti-theft device (sheet metal cover with shear bolts) over the ECMJ623Shear bolt 1 Antitheft protection Shear bolt 2610_03424Airbag / Audi pre sense basicDesignation Equipment Installation position Tasks Address Word Data bus communication Airbag Control Module J234 • Always installed • Audi pre sense basic, PR No.: 7W1. Optional Audi pre sense front, PR No.: 6K3 On the center tunnel in front of the center console • Deployment of the airbags • Audi pre sense 15 • Powertrain CAN bus participant • J234 is the LIN master for front left and right Seat Belt Tensioner Control Modules J854 and J855. • In vehicles specified for the North American market, J234 is the LIN master for Passenger Occupant Detection System Control Module J706J234610_035S tronicDesignation Equipment Installation position Task Address Word Data bus communication Special feature DSG Transmission Mechatronic J743 Always installed on vehicles with S tronic On the transmission Controling the dual clutch transmission 02 Powertrain CAN bus participant Dual clutch transmission 09D (6-speed) is used.J743610_03625Transmission selector lever sensorsDesignation Equipment Installation position Tasks Address Word Data bus communication Special feature Selector Lever Sensor System Control Module J587 All vehicles with S tronic On the selector lever housing • Signalling the selector lever position • Signalling the tiptronic commands 81 Powertrain CAN bus participant The control module can only be replaced together with the selector leverJ587610_037Headlight range control on vehicles with bi-xenon headlightsDesignation Equipment Installation position Task Address Word Data bus communication Headlamp Range Control Module J431 All vehicles with bi-xenon headlights, PR No.: 8IG Behind left side of instrument panel Dynamic headlight range control 55 CAN-Extended bus participantJ431610_03926Headlight range control on vehicles with LED headlightsDesignation Equipment Installation position Task Cornering Lamp and Headlamp Range Control Module J745 On all vehicles with: • LED headlinghts, PR No.: 8IT Behind the instrument panel on the left side • Dynamic headlight range control • Controlling the light profiles • Controlling the adaptive light 55 CAN-Extended bus participant It is connected to the power modules for the left and right headlights via a private CAN busAddress Word Data bus communication Special featureJ745610_038Audi side assistDesignation Equipment Installation position Task Address Word Data bus communication Special feature Lane Change Assistance Control Module J769 Lane Change Assistance Control Module 2 J770 Optional equipment, PR No.: 7Y1 • In the rear right bumper J769 • In the rear left bumper J770 • To scan the peripheral area behind and to the side of the vehicle • To activate the warning lights in the door mirrors 3C • J769 (master) CAN-Extended bus participant • J770 (slave) connected to J769 via private CAN participant The control modules are mounted in the bumper cover. The system must be calibrated after removal and installation.J770J769610_04027Audi active lane assist (lane departure warning system)Designation Equipment Installation position Task Address Word Data bus communication Special feature Driver Assistance Systems Front Camera R242 Optional equipment • Audi active lane assist, PR No.: 7Y5 On the windshield, above the base of the interior rear-view mirror Scanning and imaging of traffic, traffic signs and lane markers A5 CAN-Extended bus participant R242 now has all software needed for active lane assist operationR242610_04228Exterior lightingLight switchFor the 2015 A3, Light Switch E1 is a LIN slave of Vehicle Electrical System Control Module J519. The operating concept has been adopted from other Audi models.Headlamp Range Control Adjuster E102*Designation Equipment Installation position TaskLight Switch E1 Always installed Left side of instrument panel To indicate the driver's preferred light setting to Vehicle Electrical System Control Module J519 None, LIN slave, measurement values and diagnostics J519Control panel* Rotary switch Display and instrument lighting controller610_045Address WordFunctionUpper control panel* Rotary switch: 0 Lights off (in some countries the daytime running light is switched on automatically when ignition is switched on). AUTO The automatic daytime running light is switched on and off depending on the light sensor Lower control panel** Parking light Low beam Rear fog light Fog light All-weather light in vehicles with LED headlightsElectrical connections and circuitVehicle Electrical System Control Module J519 reads the four positions of the rotary switch, button operations and the position of the instrument lighting controller (where applicable) via the LIN circuit. All commands for the switch lighting and the warning lamps of the individual functions are sent to the light switch by J519. A redundancy wire is used to determine the plausibility of the switch positions. In the event of a short circuit or open circuit in the LIN or redundancy lines, the emergency light function is activated by J519 (low beams are switched on) and a DTC is entered in J519. Headlamp Range Control Adjuster E102* is integrated in the light switch housing but is a separate component. Its information is transmitted to the headlight range control servomotors via a discrete line.Light switch E1 Low beam610_046Connections of E1: Pin 1 Pin 2 Pin 3 Pin 4 LIN Terminal 30 Terminal 31 Redundancy lineConnections of E102: Pin 1 Pin 2 Pin 4 Terminal 30 Terminal 31 Activation of the headlight range control servomotors*These components are not installed on the 2015 Audi A3 at this time. ** Available on S3 models only29HeadlightsBi-xenon headlightPR no.: 8IG The component parts of the bi-xenon headlight shown can be replaced with the exception of the LED module for Daytime Running Lights. In the event a DRL failure, the entire headlight assembly must be replaced.Left HID Headlamp Bulb L13 Left Headlamp Beam Adjustment Motor V48Left Front Turn Signal Bulb M5 Sidemarker2)Left Daytime Running Lamp and Position Lamp LED Module L176Left HID Headlamp Control Module J343 Left Daytime Running Lamp and Position Lamp Control Module J860610_048Light functions Daytime running light Parking light Low beam High beam (change-over by shutter) Turn signal Sidemarker2)Illuminants used 2 LEDs with plastic optical fibres dimmed to approx. 25 % Gas discharge lamp D3SPower 18 watts35 wattsBulb PSY24W LED24 watts 0.6 wattsActivation mechanismThe functions of the bi-xenon headlights are activated by Vehicle Electrical System Control Module J519. The Daytime Running Light for the side on which a turn is being made are switched off for the duration of the turn signal activation. Left and Right Low Beam Headlamp Reflector Motors V294 and V295 are used to change over between low and high beam operation.30LED headlightsPR no.: 8IT All light functions are performed by LEDs. No fog lights are fitted in models equipped with LED headlights. The allweather light function is available as a substitute.Left headlight range servomotorParking light / daytime running light / turn signalCornering lightLeft headlight fanLow beam Sidemarker2) High beamHeadlight range control power module LED power module (Low beam, High beam, cornering light, fan activation)LED control unit (Parking light, daytime running light, turn signal, sidemarker2))610_051Light functions Daytime running light Parking light Low beam High beam Cornering light Turn signal Sidemarker2)Illuminants used 4 LEDs (1x 3 LED chip, 1x 1 LED chip) dimmed to approximately. 15 % 9 LEDs (2x 5 LED chip, 2x 2 LED chip) 8 LEDs (2x 4 LED chips) 4 LEDs (2x 2 LED chips) 4 yellow LEDs (1x 3 LED chip, 1x 1 LED chip) LEDPower 14 watts41 watts 36 watts 18 watts 16 watts 0.6 watts31Headlight range controlDynamic headlight range controlVehicles with gas discharge headlights or LED headlights are equipped with a dynamic headlight range control system. Depending on the altitude and movement of the vehicle, headlight range control servomotors V48 and V49 correct the range of the headlights. The headlight range control configurations described below are available for the bi-xenon headlights and the bi-xenon headlights with adaptive light.Schematic diagram of the activation mechanism for bi-xenon headlightsConvenience CAN busBi-xenon headlight (left-hand side of vehicle)Discrete linesVehicle Electrical System Control Module J519Left Daytime Running Lamp and Position Lamp Control Module J860 Left Front Turn Signal Bulb M5 Left HID Headlamp Control Module J343Extended CAN busHeadlamp Range Control Module J431Discrete linesLeft Headlamp Beam Adjustment Motor V48Discrete lineLeft Rear Level Control System Sensor G76610_061Schematic diagram of the activation mechanism for LED headlightsConvenience CAN busLED headlights (left-hand side of vehicle) Discrete linesVehicle Electrical System Control Module J519LED control unit (Parking light and daytime running light / turn signal) (Sidemarker with SAE1))Extended CAN busCornering Lamp and Headlamp Range Control Module J745Private CAN bus (sub-bus)LED power module (Low beam, High beam and cornering light)Discrete lines Discrete lineLeft headlight fanLeft Rear Level Control System Sensor G76Headlight range control power moduleDiscrete linesLeft headlight range control servomotor32610_063Headlight range control in vehicles with wheel damping electronics Audi magnetic rideThe 2015 S3 can be optionally equipped with Audi magnetic ride. These vehicles have four level sensors to monitor vehicle ride height. Electronic Damping Control Module J250 monitors the level sensors through discrete wires. J250 communicates over the Suspension CAN and transfers information about vehicle ride height to the headlight range control module of the particular headlight system installed.Schematic diagram of the activation mechanism for vehicles with Audi magnetic rideHeadlamp Range Control Module 1Discrete lineHeadlight range control servomotors1)Data Bus On Board Diagnostic Interface J533Cornering Lamp and Headlamp Range Control Module J745 2Private CAN bus (sub-bus)Power module for headlights2)Discrete line Suspension CAN bus Extended CAN busHeadlight range control servomotors2)Cornering Lamp and Headlamp Range Control Module J745 3Private CAN bus (sub-bus)Power module for headlight range adjustment3)Discrete lineHeadlight range control servomotors3)Electronic Damping Control Module J250Discrete linesLeft Front Level Control System Sensor G78Right Front Level Control System Sensor G289Left Rear Level Control System Sensor G76Right Rear Level Control System Sensor G77610_064with bi-xenon headlights with bi-xenon headlights with adaptive light (not for the North American region) 3) with LED headlights1) 2)33Tail lightsLED tail lightPR no.: 8SK LED tail lights are standard equipment on the Audi A3 for the North American region. They are activated by Vehicle Electrical System Control Module J519. The tail lights are also activated if the vehicle is equipped with a Coming Home / Leaving Home function. The rear fog light and the reversing light are deactivated when the rear hatch is opened. The bulbs of the rear hatch light can be accessed via a service flap. LEDs cannot be replaced. If faulty, the tail light in question must be replaced.Turn signalBack-up lightBrake lightTail light610_066Light functions Brake light Tail light Turn signal Back-up lightIlluminants used 9 LEDs 2 LEDs with plastic optical fibres 20 LEDs Bulb H6WActivation mechanism 100 % 100 % 100 % 100 %Power approx. 3.5 watts approx. 2 watts approx. 3.5 watts 6 watts34High-mounted brake lightThe high-mounted brake light is attached to the rear window. It has a total of 48 LEDs. The component parts cannot be replaced. If defective, the entire module must be replaced. The component parts of the high-level brake light cannot be replaced. If faulty, the complete component must be replaced. This is only possible after removing the rear spoiler.610_067aHigh level brake light M25License lightsThe license plate lights for the 2015 A3 sedan feature LED technology. Both lights house two LEDs. As with the highmounted rear brake light, they are activated by Vehicle Electrical System Control Module J519.610_06835eSelf Study ProgramsFor further information about the technology of the The 2015 Audi A3, refer to the following eSelf Study Programs.eSelf Study Program 990143eSelf Study Program 970343The 2015 Audi A3 IntroductionThe 2015 Audi A3 Vehicle Electronics and Driver Assistance Systems610_078a2610_079610_080aSSP 990143 The 2015 Audi A3 IntroductionSSP 970343 The 2015 Audi A3 Vehicle Electronics and Drivers Assistance SystemsSSP 960143 The 2015 Audi A3 Running Gear and Suspension Systems36Notes37Knowledge AssessmentAn On-Line Knowledge Assessment (exam) is Available for this eSelf-Study Program. The Knowledge Assessment is required for Certification. You can find this Knowledge Assessment at: www.accessaudi.com From the accessaudi.com Homepage:• • • Click on the “ACADEMY” tab Click on the “Academy site” link Click on the Course Catalog Search and select “970243 - The 2015 Audi A3 Onboard Power Supply and Networking“ Please submit any questions or inquiries via the Academy CRC Online Support Form which is located under the “Support” tab or the “Contact Us” tab of the Academy CRC.Thank you for reading this eSelf-Study Program and taking the assessment.38All rights reserved. Technical specifications are subject to change without notice. Audi of America, LLC 2200 Ferdinand Porsche Drive Herndon, VA 2017139970243