TECHNICAL DOCUMENTATION
SSP 970293 – The 2019 Audi A8 Electrics and Electronics

This PDF is currently unavailable.
Read document text
The 2019 Audi A8 Electrics and ElectronicseSelf-Study Program 970293Audi of America, LLC Service Training Created in the U.S.A. Created 01/2018 Course Number 970293©2017 Audi of America, LLC All rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC. Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.The eSelf-Study Program (eSSP) teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a repair manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. For further information about maintenance and repair work, always refer to the current technical literature.NoteReferenceRevision: June 27, 2018iiIntroduction Power supply12-volt car battery Jump start terminal 12-volt supply structure Fuses and relays Electrical wiring1 22 3 4 5 648-volt electrical systemGeneral description Components of the 48-volt electrical system Design of the 48-volt electrical system Starter Generator C29 48 Volt Battery A6 Voltage Converter, 48V/12V A7 Working on the 48-volt electrical system The 48-volt MHEV (Mild Hybrid Electric Vehicle)88 9 10 14 16 20 24 26NetworkingTopology Bus systems used in the Audi A82830 34Control modulesData Bus on Board Diagnostic Interface J533 Vehicle Electrical System Control Module J519 (BCM1) Windshield wiper and washer system Comfort System Central Control Module J393 (BCM2) Rear Lid Control Module J605 Garage Door Opener Control Module J530 Windshield Defogger Control Module J505 Instrument Cluster Control Module J285 Windshield Projection Head Up Display Control Module J898 Door Control Modules J386/J387 Memory Seat/Steering Column Adjustment Control Module J136/J521 Sunroof Control Module J245/J392 Power Adjustable Steering Column Control Module J866 Electronic Steering Column Lock Control Module J764 Steering Column Electronics Control Module J5274040 45 50 60 64 66 67 68 69 71 74 76 77 78 79Audi drive selectControllable systems Driving modes Displays and operation8080 82 83Exterior lightingOperation Headlights Matrix beam Laser lights (S8) Tail lights8484 86 94 97 98Interior lightingBackground lighting eSelf-Study Programs100100 107Knowledge assessment108iiiThis eSSP contains video links which you can use to access interactive media.ivIntroductionThe fourth generation of the brand flagship is, once again, the reference point defining the Audi brand – due to a new design language, an innovative touch concept and the introduction of mild hybrid technology (MHEV). The MHEV technology of Audi is based on the newly developed 48 volt electrical system - it supplies the 12 volt electrical system, which in this case is the electrical subsystem. The 48-volt electrical system is powered by a belt alternator starter (BAS) which is connected to the engine serpentine drive. A lithium-ion battery, positioned safely under the luggage compartment floor, serves as an energy storage device. Taken together, these measures further improve the already high fuel efficiency of the engines. The mild hybrid drive in the new Audi A8 has two central building blocks. One of them is the water-cooled belt starter generator mounted to the end face of the engine. A highperformance poly V belt connects it to the crankshaft. The belt starter generator has a recuperation capacity of 12 kW and produces up to 44.25 lb ft (60 Nm) of torque. The second component is a lithium-ion battery with a charge capacity of 10 Ah and a voltage capacity of 48 volts. The newly developed 48-volt electrical system is the main electrical system. The 12-volt electrical system is coupled to the main electrical system via a DC-to-DC converter. The lithium-ion battery housed in the luggage compartment is about the same size as a large lead acid battery. A closed-loop air cooling system provides thermal management. The 48-volt MHEV technology is particularly unobtrusive and efficient. When the driver takes his foot off the accelerator at speed of between 34.1 and 99.4 mph (55 and 160 km/h), the car can coast for up to 40 seconds with the engine completely disengaged. The start-stop phase begins at 13.6 mph (22 km/h) when coasting at low speed. For a more complete description of an MHEV, please refer to page 26.48-volt cables with violet-colored insulation48-volt battery in the luggage compartment well664_002Learning objectives of this eSelf-Study Program: This eSelf-Study Program describes the electrical and electronic systems of the 2019 A8. When finished, you will be able to: ›› Explain the components of the 48-volt electrical system. ›› Explain the functions and tasks of the Starter Generator C29. ›› List the installation locations and new features of the control modules for the electrical system, networking and comfort/ convenience electronics.1Power supply12-volt car batteryThe 12 volt battery of the A8 is located in the right hand side of the luggage compartment behind a trim panel. Depending on vehicle equipment, either an EFB1) or AGM battery2) is used. Fuse Panel SA and Battery Interrupt Igniter N253 are attached to the positive battery terminal. If the igniter is activated, the starter, secondary air pump, and radiator fans are disconnected from Terminal 30. Battery Monitoring Control Module J367 is located at the negative terminal of the 12 volt battery. J367 and the ground cable form a unit. The term battery data module (BDM) is sometimes also used for J367. The battery should only be tested using the VAS Scan Tool via GFF or Guided Functions. J367 also evaluates the history data of the battery. As in other Audi models, if the battery is replaced, it must be adapted using the Scan Tool.Battery Monitoring Control Module J367664_004Fuse holder Battery Interrupt Igniter N253EFB battery An EFB is a heavy duty wet cell battery. The positive plates are coated with an additional polyester film which provides the active mass of the battery with additional stability. The deep cycle resistance of this type of battery is higher than that of a conventional battery.AGM car battery With AGM car batteries, the battery electrolyte is absorbed by a glass microfiber mat. In addition to having higher deep-cycle resistance, the AGM car battery is noted for its leak-proof design. This is very important for installation of the battery inside the car. When charging, it is important to follow the charger's operating instructions and, if necessary, to set the charger program for AGM car batteries.The following car batteries are used in the Audi A8 worldwide:EFB battery 69 Ah/360A 70 Ah/420 AEnhanced Flooded Battery Absorbent Glass MatAGM car batteries 68 Ah/380 A 92 Ah/520 A 105 Ah/580 A1) 2)2Jump start terminalThe jump start terminal is located in the engine compartment on the right-hand side, between the coolant reservoir and the plenum chamber. This connection can also be used for charging both car batteries in the showroom or for purposes of diagnostic work in the workshop.Suppressor C24Jump start terminalDistributor TV2Distributor TV3664_005The jump starting terminal is located on the Terminal 30 distributor TV2. It is supplied with voltage via a red 70 mm2 cable from the 12-volt car battery. The Terminal 30 distributor TV3, which has three fuses, is located directly adjacent to TV2.The radiator fans, and the secondary air pump are supplied with voltage through these three fuses. The black 70 mm2 cable connecting to distributor TV2 leads to the 12-volt starter motor. The interference suppression capacitor C24 is located adjacent to the distributor.312-volt supply structureJ293J671SF J299TV3TV2SE SC SB SA SR2J367SD SH SJ SM SN SP SR3 J505 J1019 J500 N253A7 TV1664_006Key:A 12-volt battery A7 Voltage Converter, 48 V/12 V B Starter J293 Radiator Fan Control Module J299 Secondary Air Injection Pump Relay J367 Battery Monitoring Control Module J500 Power Steering Control Module J505 Windshield Defogger Control Module J671 Radiator Fan Control Module 24J1019 N253 SF SR2 SR3 TV1 TV2 TV3 Rear Axle Steering Control Module Battery Interrupt Igniter Fuse Panel F Relay and Fuse Panel 2 Relay and Fuse Panel 3 Distributor in luggage compartment, right Distributor in engine compartment on left Distributor in engine compartment on rightFuses and relaysThe fuses are identified by the letter "S" and by a number in the current flow diagram. This also applies to other individual fuses distributed throughout the vehicle. The fuses connecting to the relay and fuse holders SR2 and SR3 as well as the fuses connecting to fuse holder SF are also accessible to the driver and also described in the vehicle Owner’s Manual.Distributors TV2 and TV3Relay and Fuse Panel 1 SR1Fuse holder at positive terminal of 12-volt batteryRelay and fuse holder SR2 on A pillar at bottom left. Fuse holders SA, SB, SC and SE are located here.Fuse holder SF on left-hand side of instrument panelRelay and fuse holder SR3 in lugagge compartment on left. Fuse holders SD, SH, SJ, SM, SN and SP are located here.664_007Note When locating fuse assignments, please refer to the latest current flow diagrams in ElsaPro.5Electrical wiringMain battery leadLike its predecessor, the Audi A8 has an aluminum main battery cable. Unlike in the previous model, this is a single-piece cable. It is insulated by a red PVC coating and has a wire cross-section of 150 mm2. It begins at the positive terminal of the 12-volt battery as a flexible round conductor. It continues from the luggage compartment to the righthand side sill as a torsionally rigid flat-section conductor. Then, as a flexible round-section conductor in the area of the A pillar, it runs from through the engine bulkhead into the engine compartment to the distributor TV2.Copper wiresThe A8 electrical system is comprised largely of copper wires. The range of use extends from 0.13 mm2 wires in the area of the CAN bus network to 75 mm² wires for power supply to high-output equipment. Copper wires with smaller cross-sections can be repaired with wiring harness repair set VAS 1978 B, while wires with cross-sections of 10.0 mm² and 16.0 mm² can be repaired with wiring harness repair set VAS 631 003. Wires with cross-sections greater than 16.0 mm² have to be replaced if damaged.Repairing aluminum wiresWiring harness repair using the VAS 631003Reference For further information refer to eSelf-Study Program 970563 The 2017 A4 Electronic and Electrical Systems.6Aluminum wiresAluminum wires with cross-sections of 2.5 mm2, 4.0 mm2 and 6.0 mm2 are used in addition to the main battery cable. Unlike the main battery cable, these wires can, if damaged, be repaired with wiring harness repair set VAS 631 001. The use of aluminum alloys in certain areas of the vehicle provides a further reduction in the weight of the wiring harness. Aluminum wires are not installed in areas where wires are moved, for example, in the doors, because they are less flexible than copper wires.Main battery cable664_008748-volt electrical systemGeneral descriptionThe 2019 A8 is the first North American Audi model to be powered by a 48-volt electrical system. It uses a watercooled 48-volt belt starter generator and a 48-volt lithiumion battery. The 48-volt main electrical system also provides the basis for the mild hybrid technology. The Audi A8 is also known commonly as a 48-volt MHEV (Mild Hybrid Electric Vehicle). Two new terminal designations were introduced at the launch of the 48-volt electrical subsystem: ›› Terminal 40 for the 48-volt positive side. ›› Terminal 41 for the 48-volt negative side.12-volt pinion-type starter664_06012-volt cable48-volt cable48-volt power distributor48-volt belt starter generator8Components of the 48-volt electrical systemThe main components of the 48-volt electrical system are the belt starter generator and the lithium-ion battery. The belt starter generator is the power source for the 48-volt electrical system. If operated as a starter, it has to be considered a power consumer within the 48-volt system. The voltage converter is the link between the 48-volt electrical system and the 12-volt electrical system. The 12-volt electrical system, with its lead acid battery, supplies all 12-volt power consumers. At the launch of the Audi A8 these include all control modules as well as the 12-volt pinion-type starter. However, it is only used for cold-starting the TFSI engine or for starting it for the first time. All other starting processes are implemented using the 48-volt belt starter generator.Circuit diagram12-volt pinion-type starter 48-volt / 12-volt converter 48-volt belt starter generator12 volts48 volts==12-volt power consumer12-volt battery48-volt battery48-volt power consumer664_061Energy managementData Bus on Board Diagnostic Interface J533 (gateway) handles the task of energy management for the 12-volt electrical system as well as the 48-volt electrical system. J533 receives information on the status of the 12-volt battery from Battery Monitoring Control Module J367, which communicates with J533 via a LIN bus. The belt starter generator sends information across a sub-bus system to Engine Control Module J623, which in turn, communicates with the gateway via the FlexRay bus. The gateway communicates with the voltage converter and the 48-volt battery via the hybrid CAN bus. For a schematic diagram of the 48-volt electrical system including the 12-volt components relevant to the power supply, refer to the following double page.9Design of the 48-volt electrical systemSchematic diagramEngine Control Module J623Term. 30 Term. 31Term. 41Distributor TV66 in the engine compartment Starter Generator C29Power distributor, term. 30Term. 30Term. 31Term. 30Term. 31 Battery, 12 V ABattery Monitoring Control Module J367xTerm. 30Data Bus on Board Diagnostic Interface J533Key:Hybrid CAN FlexRay LIN bus Sub-bus systems 12 volts DC X Discrete signal lines 48-volt DC positive side 48-volt DC negative side To the 12-volt power consumers10Airbag Control Module J234Distributor TV 67 on the 48-volt batteryTerm. 30Term. 31Term. 41Term. 40Term. 41Term. 40 Battery, 48 V A6Voltage Converter, 48 V/12 V A7664_06211Overview of the 48-volt componentsTerminal 40 connection in distributor TV348-volt positive cableStarter Generator C29Key:48-volt DC voltage cables 12-volt DC voltage cables12Voltage Converter, 48 V/12 V A7Battery, 48 V A6664_06313Starter Generator C29General descriptionStarter Generator C29 is a 48-volt belt starter generator. As a generator, it charges the 48-volt battery and supplies the voltage converter with 48 volts DC. As an electric motor, it can be used both as a starter and as a booster for the TFSI engine. It is water-cooled and has an electrical water pump. C29 communicates with the engine control module via a sub-bus connection (private CAN bus) and activates Starter Generator Coolant Pump V621 by generating a pulse-width-modulated (PWM) signal.Engine Control Module J6231 2 3 4 5 6 7 8 Terminal 41Terminal 30Sub-bus PWM Terminal 31664_065Terminal 40 8-pin connectorStarter Generator Coolant Pump V621664_064 664_066Activation of Starter Generator Coolant Pump V621 V621 is activated in an engine-specific fashion. It is connected directly to the engine control module. The integration of V621 into the engine cooling system varies from one engine type to another. In some engines coolant flow through the starter generator is assisted by the main water pump, while in others it is not. SpecificationsDesignation Address Word Communication 48-volt positive / negative terminal designations Nominal rpm Transmission ratio (starter generator /TFSI engine) Rated voltage in motor mode Rated voltage in generator mode Rated output in motor mode (boost for the TFSI engine, for maximum 5 seconds) Rated output in generator mode (recuperation 2, for maximum 5 seconds) Continuous rated output in generator mode Maximum torque in motor mode Starter Generator C29 00CC Private CAN to engine control module 40/41 6000 rpm 2.72 – 3.40 (depending on engine type) 40 volts 51.5 volts approximately 8 hp approximately 18 hp approximately 6 hp 60 NmIn some cases, V621 performs additional tasks within the engine cooling system. The conditions under which the starter generator coolant pump is operated are defined in the engine control module software. The pump can be activated using the VAS Scan Tool.1)Recuperation: energy recovery, for example, in overrun or under braking, the kinetic energy of the vehicle is transformed into electrical energy. 14Connection to the TFSI engineThe Starter Generator C29 and the TFSI engine are connected by a poly V belt. The starter generator places heavy demands on the belt tensioner as is the driven element in generator mode, but is the driving element during engine operation, for example, during start-up. The tensioning element of the belt tensioner has been adapted to meet the requirements of each engine and can be attached directly to the starter generator or to the engine block. It is important that the belt tensioner provide the poly V belt with as large an arc of contact as possible around the starter generator belt pulley.C29 operating as a generatorC29 operating as a starter664_067664_068Examples of belt tensioner versions The illustration shows the starter generator of a 3.0l TFSI engine. The belt tensioner is attached to the engine block.664_069Note No provision had been made for periodic replacement of the poly V belt at the time of preparation of this eSelf-Study Program. Always refer to the instructions given in the service literature.1548 Volt Battery A6Installation locationThe 48 volt battery is installed in the spare tire well. It is a lithium ion battery. This type of battery has advantages over lead acid batteries such as higher energy density and higher deep cycle resistance. However, lithium ion batteries have to be protected from exhaustive discharge cycles which can cause the battery cells to short circuit. Mechanical damage can also cause internal short-circuiting and chemical reactions due to the ingress of atmospheric moisture. The battery housing is made from plastic. It is also covered inside the vehicle by a metal enclosure attached to the vehicle underbody.48-volt battery housed in protective enclosure664_07148-volt battery in the spare wheel wellVent line (vents battery gases)Battery components ›› ›› ›› ›› ›› ›› Plastic battery housing. Control module (battery management). 13 lithium-ion battery cells. 1 relay. 1 fuse. Fans.Connectivity A6 is a hybrid CAN user and can be accessed with the VAS Scan Tool using Address Word 21. The positive side of the 48-volt DC voltage system is designated "Terminal 40" and the negative side is designated "Terminal 41". The control module in the 48-volt battery measures the voltage and temperature of the individual cells and transfers this data to Data Bus on Board Diagnostic Interface J533. In addition to this, it activates the internal fans if a critical storage temperature is reached.16SpecificationsDesignation Address Word Communication Positive/negative terminal designations Rated voltage in V Capacitance in Ah Number of cells Cell voltage in V Operating temperature Weight Cooling48 Volt Battery A6 21 Hybrid CAN 40/41 48 9.6 13 3.68 - 22 to 140 °F (-30 to 60 °C) Approximately 22.0 lb (10 kg) Air (active) via fans664_07348-volt negative terminal Terminal 41 Connection for the battery-integrated control moduleBattery-integrated fuse The fuse is not designed for replacement 48-volt positive terminal Terminal 40Battery-integrated control module In addition to the 12-volt power supply and the hybrid CAN communication lines for the control module, signal wires running from the Airbag Control Module J234 are still connected to the battery-integrated control module. In an airbag deployment situation, the power contactor in the battery A6 is opened and the 48-volt electrical system is de-energized.17Battery design14-terminal connector 12-volt sideBattery-integrated control module (battery management)Cell assembly: 13 battery cellsSteel base plateBattery housing bottom sectionCharging, jump-starting and replacement When the engine is running, the 48-volt battery is charged directly by the starter generator. When an external 12-volt charger is used for charging at the 12 volt jump start terminal, the 48-volt battery is charged via the voltage converter. There is no provision for connecting a charger directly to the 48-volt battery.18The 12-volt jump start terminal in distributor TV 3 is available for jump-starting.Battery-integrated fuse coverBattery housing Top sectionConnection plate with relay, fuse and 48-volt terminal studPlug-in module with a single battery cellVent valve (vents battery gases)664_074The VAS Scan Tool must be used for battery testing (classification). The battery data is read from the built-in control module of the 48-volt battery and assessed.If the battery is not installed in the vehicle, the Scan Tool can be connected to a battery via high-voltage diagnostic box VAS 5581 and adapter cable VAS 5581/1A.19Voltage Converter, 48V/12V A7Installation location A7 is installed behind the right-hand luggage compartment trim above the 12-volt battery, Like the 12-volt battery, the voltage converter can be accessed after removing the protective cap.664_075CoverVoltage Converter, 48V/12V A7Function The Voltage Converter, 48 V/12 V A7 is a bidirectional voltage converter. This means that the 12 volts generated by the alternator is converted to 48 volts. It is also converted back to 12 volts in order to charge the 12 volt battery. In addition, the 12 volts can be converted to 48 volts under certain conditions. This happens when, for example, an external charger is connected to the vehicle via the 12-volt jump start terminals.Activation of Control Module Cooling Fan V274 V274 is activated by the voltage converter. The three wires from the 3-pin fan connector lead directly into the 10-pin connector at the voltage converter. The fan does not run continuously when the engine is running, but only when the voltage converter requires active cooling. The fan does not have a run-on function. To check the fan, technicians have the option of running an actuator output check for the V274 using the Address Word of the voltage converter.20SpecificationsDesignation Address Word Communication Terminal designations 48V positive/negative Terminal designations 12 V Power in kW Weight CoolingVoltage converter, 48 V / 12 VA7 C4 Hybrid CAN 40/41 30 Approximately 3 Approximately 5.51 lb (2.5 kg) Air (passive)Voltage Converter, 48 V/12 V A73-pin connector Activation of the fan10-pin connector 12-volt sideControl Module Cooling Fan V274664_076Connector, 48 volts positive Terminal 40 Threaded stud, 48 volts negative Terminal 41Threaded stud, 12 volts positive Terminal 3021ConnectionsThe connector for Terminal 40 as well as the two threaded studs for Terminals 41 and 30 are protected by a cover flap. To access the terminals, this flap first has to be unlocked and then opened. The 10-pin connector prevents the coverflap from being unlocked (moved). The flap cannot be unlocked until the connector has been disconnected from the voltage converter. The flap can then be opened, providing access to the terminals.Unlocking the flapOpening the flap3. 2. 1.664_077 664_078Operating scenarios Even if driving represents the "normal" operating state of a vehicle, other scenarios are possible. These scenarios and their effects on the voltage converter as well as the 48-volt and 12-volt batteries are summarized in the following table.Engine operation yes Terminal 15 on External 12-volt charger no Voltage converter 48 volts → 12 volts Relays in the 48-volt battery is closednoonno48 volts → 12 voltsis closednoonyes12 volts → 48 voltsis closednooffyes12 volts → 48 voltsis closednooffnonot functionalopen2210-pin connectionThe hybrid CAN wires are also integrated into the 10-pin plug-in connection. If the voltage converter is disconnected from the communication lines when Terminal 15 is active, for example, by disconnecting the 10-pin plug-in connector, the voltage converter is deactivated.The relay in the 48-volt battery stays closed and the 48-volt electrical system stays active. The 12-volt system also stays active but the 12-volt battery is no longer charged.10-pin connector 12-volt side664_07812-volt battery is charged48-volt battery is chargedRemarks The 48-volt generator runs, charges the 48-volt battery and supplies the voltage converter, which, in turn, converts the voltage and charges the 12-volt battery. The 48-volt battery boosts the 12-volt electrical system via the voltage converter in certain operating states. Charger is detected – 12-volt charger charges 12-volt battery. Voltage converter transforms voltage to 48 volts and charges 48-volt battery. If insufficient charging current is available for the 12-volt battery because an underrated charger is used, the voltage converter does not supply 48 volts for this Terminal 15 cycle and, therefore, the 48-volt battery is not charged. Charger is detected – 12-volt charger charges 12-volt battery. Voltage converter transforms voltage to 48 volts and charges 48-volt battery. The 48-volt battery is "disconnected". The 12-volt battery is discharged depending on the vehicle's static current.is boostedis dischargedis chargedis chargedis not chargedis chargedis chargedis dischargedis disconnected23Working on the 48-volt electrical systemAim The use of 48-volt systems in automative systems is a potential source of electrical hazards. Service employees must be able to identify a 48-volt electrical system and safely perform whatever work is necessary. All work on the 48-volt electrical system may only be performed by trained employees with a basic knowledge of electrics and with the system de-energized.Recognition and identification Positive wires of the 48-volt electrical system DC voltage at Terminal 40 Ground wires of the 48-volt electrical system DC voltage at Terminal 41 Warning label on the 48-volt battery664_081Warning label on the protective caps of the 48-volt‑battery and the 48-volt distributor boxes664_08224HazardsThe following hazards can occur when performing work on an active 48-volt electrical system in the event of a fault or incorrect handling: Taking out of service Before working on the 48 volt electrical system, it must first be de-energized. This is done through Guided Functions using the VAS Scan Tool. Through Guided Functions, Data Bus On Board Diagnostic Interface J533 opens the relay of the 48 volt battery which shuts down the system in a defined order. To confirm the system has been de-energized, you must read the voltage value of the battery and Voltage Converter, 48V/12V A7. An inspection report is part of the de-energizing Test Plan and must be printed out and signed by the Technician. It should include the vehicle's details as well as the measurement data for the 48-volt system. After that, it must be attached to the vehicle in an easily visible place. In the event of an “Not OK” inspection report/finding, the 48-volt system must be shut down manually.›› Short circuits. ›› Arcing. ›› Secondary hazards (burns due to molten metal spatter as well as injuries due to startled reaction).Test log of 48-volt system, confirming manual voltage de-energization Use only Guided Fault Finding / functions to de-energize the 48-volt system in the vehicle and check the de-energization status (absence of power) VIN: Date: Name: ._._._._._._._._._._._._._._._._._. __________________________ __________________________Telephone: __________________________ Function test of Test Instruments on 12-volt battery.Measuring tool check - Reference voltage measurement 12-volt battery Measured voltage __________ V; Specified value: Current 12-volt battery voltage +/- 10% Determine the de-energization status on the deactivated 48-volt system using Test Instruments.Measurement 1 - Voltage measurement on control module Battery, 48 V -A6Measured voltage __________ V; Specified value: 5 volts Measurement 2 is only performed when the value of measurement 1 is outside the specified value range.Measurement 2 - Voltage measurement on control module Voltage converter, 48 V/12 V -A7Measured voltage __________ V; Specified value: 0.5 voltsExample of an inspection report (page 1 of 6) the display on the diagnostic tester may be slightly different)Returning to service The 48-volt system is returned to service after completion of work/repairs by running the Test Plan in "Guided Functions". If the system is not returned to service, the vehicle runs without a durable 48-volt/12-volt voltage supply, that means the 12-volt-battery is not charged. As soon as the 12-volt battery is discharged completely, the vehicle is no longer roadworthy. For this reason, special guidelines apply to the storage, transportation and recycling of lithium-ion batteries. Special emphasis is placed here on the handling of critical batteries. These processes are often subject to national regulations. When handling lithium-ion batteries, all statutory requirements applicable in your country as well as all instructions given in the service literature and Guided Fault Finding in ODIS.Hazards due to lithium-ion technologyHazards can also occur due to the design of a lithium-ion battery and electro-chemical processes inside a lithium-ion battery. The electrolyte in the lithium-ion battery is easily flammable, potentially explosive, causes chemical burns and emits toxic vapors.Note Always refer to the service literature for information on handling requirements for lithium ion batteries.Note For a detailed description of the procedures for de-energizing, repairing and starting up the 48-volt electrical system, please refer to the current service literature.25The 48-volt MHEV (Mild Hybrid Electric Vehicle)General descriptionThe abbreviation MHEV stands for Mild Hybrid Electric Vehicle. These vehicles generally have an additional battery as well as a small e-machine. This means that functions such as extended recuperation and internal combustion engine assistance by the e-machine (boost) are possible. The TFSI engine is generally responsible for drive and for generating electrical energy. All-electric driving is not possible with the Audi A8 MHEV. The Audi A8 is designed as a 48-volt MHEV. The 48-volt battery serves as an auxiliary battery and the starter generator as the e-machine.Mild hybrid functionsThe 48-volt MHEV concept offers drivers a number of new functions which enhance both efficiency and ride comfort. These additional functions also require additional controls and displays. The following functions have been implemented in the 2018 Audi A8. ›› Start-stop at speeds of less than 13.6 mph (22 km/h). ›› Internal combustion engine assistance by the starter generator. ›› Extended recuperation. ›› Intelligent coasting with internal combustion engine shut-off. ›› More comfortable internal combustion engine start-up by the starter generator. ›› More comfortable internal combustion engine shut-off by the starter generator. ›› Immediate restarting of the internal combustion engine by the starter generator (change of mind).Extended recuperationIn recuperation mode, the vehicle's kinetic energy is used to charge the battery during overrun phases. Thanks to their auxiliary battery, mild-hybrid vehicles have a higher recuperation capacity than previous vehicles. The Audi A8, with its lithium-ion battery and the 48-volt starter generator has a recuperation capacity of up to 12 kW. The so-called "overrun recuperation" cycle is indicated by a 50% display in the instrument cluster. The "extended recuperation" cycle is initiated by efficient assist and indicated by the 100% display in the instrument cluster.Maximum recuperation664_134Medium recuperation664_13326Improvements by starter generatorThe use of the starter generator makes restarting the TFSI engine while driving much more comfortable than is the case with conventional pinion-type starters. The fact that the starter generator is permanently coupled to the engine via the poly V belt allows it to be restarted even if it has not yet come to a complete standstill. This situation can occur if, for example, the engine is shut off by the start-stop system, but has not come to a complete standstill and the driver presses the accelerator because he wants to continue driving (change of mind situation). A further improvement stems from the fact that the TFSI engine can be braked precisely by the starter generator during shut-off, allowing “shut-off judder” to be reduced significantly. The starter generator can be used as an e-machine while the engine is running and can assist the engine in certain load ranges, thus improving fuel economy. The starter generator in the Audi A8 is not designed to boost the torque and/or power output of the TFSI engine.664_06927NetworkingSome of the control modules shown in the overview are optional and/or country-specific equipment. For the sake of clarity, not all control modules fitted in the vehicle can be shown here. Refer to the current service literature for details of control modules installation positions, as well as instructions for installation and removal.J387 J428J1023A27 J1089R161J794 J521J1122J500J792R242J234J245J775J764 J1088 J104 J853 J1121 J898 J285 J527 J869 A31 J136J1018 J623 J931J519 J386Key A6 A7 A27 A31 J104 J136 J187 J234 J245 J285 J386 J387 J392 J393 Battery, 48 V Voltage Converter, 48 V/12 V Right LED Headlamp Power Output Module 1 Power module 1 for left LED headlight ABS Control Module Memory Seat/Steering Column Adjustment Control Module Differential Lock Control Module Airbag Control Module Sunroof Control Module Instrument Cluster Control Module Driver Door Control Module Front Passenger Door Control Module Rear Sunroof Control Module Comfort System Central Control Module J428 Control Module for Adaptive Cruise Control J500 Power Steering Control Module J505 Windshield Defogger Control Module J519 Vehicle Electrical System Control Module J521 Front Passenger Memory Seat Control Module J525 Digital Sound System Control Module J527 Steering Column Electronics Control Module J533 Data Bus on Board Diagnostic Interface J605 Rear Lid Control Module J623 Engine Control Module J764 Electronic Steering Column Lock Control Module J769 Lane Change Assistance Control Module J770 Lane Change Assistance Control Module 2 J772 Rearview Camera System Control Module J775 Drivetrain Control Module28J927A7J769J505J187J392J533J1019A6J772J605J525 J393 J770J926661_091J792 J794 J853 J869 J898 J926 J927 J931 J1018 J1019 J1023 J1088 J1089 J1121 J1122 Active Steering Control Module Information Electronics Control Module 1 Night Vision System Control Module Structure Borne Sound Control Module Windshield Projection Head Up Display Control Module Driver Side Rear Door Control Module Passenger Side Rear Door Control Module Subframe Mount Control Module Left Light Control Module Rear Axle Steering Control Module Right Light Control Module Control Module for Left Front Object Detection Radar Sensor Control Module for Right Front Object Detection Radar Sensor Driver Assistance Systems Control Module Laser Distance Regulation Control ModuleR161 R242 DVD Changer Driver Assistance Systems Front Camera29TopologyJ926J386J927J387J605 Data Link ConnectorN209J136J764J453N475J245U13A6N210J521J392J367A7N477N479J876N480E660G65A31N481J877G1052J1018N482G1053A27E661H12Servomotors 1-5Background light 1-15J1023J505J391Background light 16-30G578 Comfort System Central Control Module J393Servomotors 1-4 Servomotors 5-7Background light 30-45J938J126MX3E774-E778 E884 Heating control 1-4Vehicle Electrical System Control Module J519J866V388 V390 V389 V391MX4G935MX13V520 V522 V524 V526V438 V113E1MX13J897G397 355J1169E265G929J400J1170Servomotors 1-15J1101J1100Key:Comfort/convenience systems CAN Hybrid CAN Extended CAN Infotainment CAN Diagnostics CAN FlexRay Modular Infotainment Matrix (MIB) CAN LIN bus30E859E857J1147R293Y32J648E67Y31J648J1060J525R161J1146J685Information Electronics Control Module 1 J794J898J285J587 J1121 Data Bus on Board Diagnostic Interface J533 Driver Assistance Systems Control Module J1121J1088M67R242J1089J853R243J794Ultrasound sensors 1-12J769R212M68R244J770J772R245J428EX22R246J1122J869EX23J706J234J104J931J854J855J1019J1097J1098J792J187J500J530J623J775J1135Y7J217V475J528WX2C29J527664_087Sub-bus systems MOST bus LVDS Instrument cluster CANUSB lines Ethernet port Comfort/convenience systems CAN 231Key:A6 A7 A27 A31 C29 E1 E67 E265 E660 E661 E774 E775 E776 E777 E778 E857 E859 E884 EX22 EX23 G65 G355 G395 G397 G578 G929 G935 G1052 G1053 H12 J104 J126 J136 J187 J217 J234 J245 J285 J345 J367 J386 J387 J391 J392 J400 J428 J453 J500 J502 J505 J521 J525 J527 J528 Battery, 48 V Voltage Converter, 48 V/12 V Right LED Headlamp Power Output Module 1 Left LED headlight power module 1 Starter Generator Light Switch Driver Volume Control Rear A/C Display Control Head Driver Side Rear Multi-Contour Seat Switch Passenger Side Rear Multi-Contour Seat Switch Front A/C Display Control Head 1 Front A/C Display Control Head 2 Front A/C Display Control Head 3 Front A/C Display Control Head 4 Front A/C Display Control Head 5 Auxiliary Display Control Head 1 Wireless Control Head 1 Front A/C Display Control Head 6 Switch Module in Instrument Panel, Center Center Console Switch Module 1 High Pressure Sensor Humidity Sensor A/C Pressure/Temperature Sensor Rain/Light Recognition Sensor Anti-Theft Alarm System Sensor Vehicle Interior Carbon Dioxide Concentration Sensor Exterior Air Quality and Humidity Sensor Low Pressure Side A/C Pressure/Temperature Sensor High Pressure Side A/C Pressure/Temperature Sensor Alarm Horn ABS Control Module Fresh Air Blower Control Module Memory Seat/Steering Column Adjustment Control Module Differential Lock Control Module Transmission Control Module Airbag Control Module Sunroof Control Module Instrument Cluster Control Module Towing Recognition Control Module Battery Monitoring Control Module Driver Door Control Module Front Passenger Door Control Module Rear Fresh Air Blower Control Module Rear Sunroof Control Module Wiper Motor Control Module Control Module for Adaptive Cruise Control Multifunction Steering Wheel Control Module Power Steering Control Module Tire Pressure Monitoring Control Module Windshield Defogger Control Module Front Passenger Memory Seat Control Module Digital Sound System Control Module Steering Column Electronics Control Module Roof Electronics Control Module J530 J587 J604 J605 J623 J648 J649 J685 J706 J764 J769 J770 J772 J775 J792 J853 J854 J855 J866 J869 J876 J877 J897 J898 J926 J927 J931 J938 J1018 J1019 J1023 J1060 J1088 J1089 J1097 J1098 J1100 J1101 J1122 J1135 J1146 J1147 M67 M68 MX3 MX4 MX13 Garage Door Opener Control Module Selector Lever Sensor System Control Module Auxiliary Heater Control Module Rear Lid Control Module Engine Control Module Left Rear Information Display Control Head Control Module Right Rear Information Display Control Head Control Module Front Information Display Control Head Passenger Occupant Detection System Control Module Electronic Steering Column Lock Control Module Lane Change Assistance Control Module Lane Change Assistance Control Module 2 Rearview Camera System Control Module Drivetrain Control Module Active Steering Control Module Night Vision System Control Module Left Front Seat Belt Tensioner Control Module Right Front Seat Belt Tensioner Control Module Power Adjustable Steering Column Control Module Structure Borne Sound Control Module Driver Side Rear Seat Adjustment Control Module Passenger Side Rear Seat Adjustment Control Module Air Ionization System Control Module Windshield Projection Head Up Display Control Module Driver Side Rear Door Control Module Passenger Side Rear Door Control Module Subframe Mount Control Module Power Rear Lid Opening Control Module Left Light Control Module Rear Axle Steering Control Module Right Light Control Module Front Information Display Control Head 2 Control Module for Left Front Object Detection Radar Sensor Control Module for Right Front Object Detection Radar Sensor Left Rear Seat Belt Tensioner Control Module Right Rear Seat Belt Tensioner Control Module Windshield Washer Pump Control Module Air Freshening System Control Module Laser Distance Regulation Control Module Level Control System Compressor Electronics Mobile Device Charger 1 Mobile Device Charger 2 Left Auxiliary High Beam Bulb Right Auxiliary High Beam Bulb Left Tail Lamp Right Tail Lamp Center Tail Lamp32Key:N209 N210 N475 N477 N479 N480 N481 N482 R64 R161 R212 R242 R243 R244 R245 R246 R293 Driver Lumbar Support Adjustment Valve Block Front Passenger Lumbar Support Adjustment Valve Block Valve Block 1 in Driver Seat Valve Block 1 in Front Passenger Seat Valve Block 1 in Driver Side Rear Seat Valve Block 2 in Driver Side Rear Seat Valve Block 1 in Passenger Side Rear Seat Valve Block 2 in Passenger Side Rear Seat Parking Heater Radio Receiver DVD Changer Night Vision System Camera Driver Assistance Systems Front Camera Front Peripheral Camera Left Peripheral Camera Right Peripheral Camera Rear Peripheral Camera USB Distributor V66 V113 V388 V389 V390 V391 V438 V475 V520 V522 V524 V526 WX2 Y7 Y31 Y32 Level Control System Compressor Motor Recirculation Door Motor Driver Seat Backrest Blower Fan Front Passenger Seat Backrest Blower Fan Driver Seat Cushion Blower Fan Front Passenger Seat Cushion Blower Fan Fresh Air Door Motor Transmission Fluid Auxiliary Hydraulic Pump 1 Left Rear Backrest Fan 1 Left Rear Seat Cushion Fan 1 Right Rear Backrest Fan 1 Right Rear Seat Cushion Fan 1 Rear Interior Lamp Automatic Dimming Interior Rearview Mirror Multimedia Display Unit 3 Multimedia Display Unit 4New features of the bus systemsAs the diagram on the pervious page shows, the number of control modules, sensors and actuators which participate in data communications in one form or another is steadily increasing. What is especially striking is the large number of LIN users which are connected to Vehicle Electrical System Control Module J519. This is in part because the climate control system is now also a function of J519. This means that a separate air conditioning control module is no longer installed in the Audi A8. Address Word 08 is no longer used for the climate control system. All climate control diagnostic functions are implemented via Address Word 09. The topology diagram cannot provide a realistic representation of the actual networking situation, especially in the area of the FlexRay bus. In the case of the LIN bus users, multiple LIN slaves are grouped together in the diagram in order to provide some measure of clarity. In the area of the AC servomotors or the interior light modules, for example, only one LIN user is shown symbolically, although the LIN slaves are actually daisy-chained. The following table provides an overview of the bus systems used in the Audi A8.33Bus systems used in the Audi A8Bus system Comfort/convenience systems CAN Comfort/convenience systems CAN 2 Extended CAN Infotainment CAN Modular Infotainment Matrix (MIB) CAN Diagnostics CAN Instrument cluster CAN Hybrid CAN FlexRay MOST bus LIN bus Sub-bus system LVDS1) Ethernet Cable color Configuration Electrical bus system Electrical bus system Electrical bus system Electrical bus system Electrical bus system Data transfer rate 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/s 500 kbit/sElectrical bus system Electrical bus system Electrical bus system Electrical bus system Fiber-optic bus system Electrical single-wire bus system Electrical bus system Electrical bus system Electrical bus system500 kbit/s 500 kbit/s 500 kbit/s 10 Mbit/s 150 Mbit/s 20 kbit/s 500 kbit/s 1 Mbit/s 200 Mbit/s 100 Mbit/sLVDSThis data transfer system is notable for its relatively low voltage. As is the case with high-speed CAN bus systems, the differences in voltage are evaluated. In the case of LVDS, the voltage is approximately 0.3 V. A typical application of LVDS is the activation of liquid crystal monitors. The LVDS cables in the Audi A8 are used, for example, to transfer image data between Information Electronics Control Module 1 J794, Instrument Cluster Control Module J285 and both MMI touch screens. The LVDS lines are sheathed, much like the FlexRay lines. Unlike the FlexRay bus, the sheathing of the LVDS lines not only protects against mechanical stresses and moisture, but also shields against electromagnetic interference. In the event of damage, LVDS lines must always be replaced rather than repaired.1)LVDS = Low Voltage Differential Signaling34EthernetEthernet is a technology developed and specified for data networks (LANs2)). This technology is commonly referred to as LAN technology. It provides data transfer rates ranging from 10 Mbit/s to 100 Gbit/s, depending on configuration level. "Fast Ethernet" system with a data transfer rate of 100 Mbit/s is used in Audi models. This form of data transfer is used in the Audi A8 for communication between the VAS Scan Tool and the gateway as well as between the Information Electronics Control Module 1 J794 and the Driver Assistance Systems Control Module J1121. The high-speed transfer of data between the Scan Tool and the gateway significantly reduces the time required for parameterizing and updating control modules. The Ethernet connection between Information Electronics Control Module 1 J794 and the Driver Assistance Systems Control Module J1121 is used for fast updating of J1121. For this purpose, an SD card containing the required data is inserted into J794, and then the data is transfered across the Ethernet line. This process is much faster than transferring data first to the gateway and then via FlexRay to the J1121.FlexRayThe aim of using the FlexRay bus is to meet the rising demands on in-car connectivity in future. It is particularly worth noting that the FlexRay bus offers much higher data transfer rates and a higher level of fail safety than the CAN bus. These are indispensable features given the many complex dynamic control systems and driver assistance systems.The FlexRay bus has the following features: ›› Electrical two-wire bus system. ›› Data transfer rate: maximum 10 Mbit/s. ›› Data transfer with three signal states: ›› "Idle" – both bus wires have a voltage of 2.5 V. ›› "Data 0" – the bus positive wire has a low voltage level and the bus negative wire has a high voltage level. ›› "Data 1" – the bus positive wire has a high voltage level and the bus negative wire has a low voltage level. ›› "Active" star topology (gateway). ›› Real-time capability. ›› Enables distributed control and the use of safety-related systems.Time [ns]664_0961 bit Differential voltage664_09735Repairing a FlexRay lineThe FlexRay wires are twisted in the same way as the CAN wires. Depending on model and year of manufacture, these wires may be sheathed or non-sheathed. In principle, sections of FlexRay lines can be replaced. Note the untwisted length (1) and the unsheathed length (2). Always refer to the electronic service and repair literature for specifics.2)LAN = Local Area NetworkVoltage [V]FlexRayGiven that the overall topology diagram cannot provide a realistic representation of the layout of the FlexRay control modules, the following diagrams show how the modules are distributed to the individual FlexRay branches. The control modules of the 2019 A8 are shown here with a full range of features. As always with the FlexRay bus, the modules connected to the end of a branch have a resistance of 94 ohms. The intermediate control modules have a resistance of 2.6 kohms. The FlexRay technology allows the use of two channels per branch - an option not utilized in previous Audi models. These channels are designated channel "A" and channel "B". The 2nd channel generally offers two options: ›› Sending data redundantly for higher fail safety. ›› Doubling the volume of transferable data.J10494 ΩJ50094 ΩJ52794 ΩJ23494 ΩJ6232.6 kΩJ2172.6 kΩJ7922.6 kΩJ11212.6 kΩJ7752.6 kΩBranch 1A94 ΩBranch 2A94 ΩBranch 3A94 ΩBranch 4A94 Ω 94 ΩJ533Branch 8A2.6 kΩJ18794 ΩJ1019664_094Reference For further information about the design and working principle of the FlexRay bus, refer to eSelf-Study Program 970103 The 2011 Audi A8 Convenience Electronics and Networking Systems.36The "B" channel in the Audi A8 is used to increase the volume of transferable data. If the same control module is connected to both channels, the diagnostic data of this module is transferred via channel "A". If a branch channel fails, for example, due to a short circuit in the FlexRay lines, the channel affected by the fault is also indicated in the diagnostic tester. This allows the relevant control modules and/or lines to be systematically tested.As data transfer across the FlexRay bus is time-controlled, the network may only be started up by "cold start" control modules. These are the following control units in the Audi A8: ›› Data Bus on Board Diagnostic Interface J533. ›› ABS Control Module J104. ›› Airbag Control Module J234.J10494 ΩJ112194 ΩJ23494 ΩJ4282.6 kΩJ7692.6 kΩJ7702.6 kΩJ11222.6 kΩJ10892.6 kΩJ10882.6 kΩBranch 1B94 ΩBranch 2B94 ΩBranch 3B94 ΩJ533664_095Key:J104 J187 J217 J234 J428 J500 J527 J533 J623 J769 ABS Control Module Differential Lock Control Module Transmission Control Module Airbag Control Module Control Module for Adaptive Cruise Control Power Steering Control Module Steering Column Electronics Control Module Data Bus on Board Diagnostic Interface (gateway) Engine Control Module Lane Change Assistance Control Module J770 J775 J792 J1019 J1088 Lane Change Assistance Control Module 2 Drivetrain Control Module Active Steering Control Module Rear Axle Steering Control Module Control Module for Left Front Object Detection Radar Sensor J1089 Control Module for Right Front Object Detection Radar Sensor J1121 Driver Assistance Systems Control Module J1122 Laser Distance Regulation Control Module37Optical data bus system MOST150664_098HistoryThis data bus system is named after the "Media Oriented Systems Transport (MOST) Cooperation". This organization is made up of various automobile manufacturers, their components suppliers and software companies which joined forces to create a standardised high-speed data transfer system. The term "Media Oriented Systems Transport" means that address-oriented messages are sent to a specific recipient. This technology is used in Audi cars to transfer data within the infotainment system.MOST150The MOST150 was first used by Audi in the A3. The new Audi A8 also benefits from this advancement in MOST technology. The data transfer rate is six times that of the MOST25. The development process necessitated making various modifications to the components of the MOST bus. For instance, the transmitter and receiver units – Fiber Optical Transmitters (FOT) – had to be adapted. Other components such as the optical connectors, the fiber optics and the electrical connectors of the control units are identical to those of the MOST25.Systems managerIn the Audi A8, up to six control modules, including, for the first time, the windshield projection control module (headup display), can be integrated into the MOST ring in the following order. ›› Information Electronics Control Module 1 J794. ›› Instrument Cluster Control Module J285. ›› Windshield Projection Head Up Display Control Module J898. ›› DVD Changer R161. ›› Digital Sound System Control Module J525. In the Audi A8, Information Electronics Control Module 1 J794 acts not only as the system manager for the MOST bus but also as the diagnostic manager - a function previously assigned to theData Bus on Board Diagnostic Interface J533 in the Audi A8. As always with a MOST bus in Audi vehicles, the control modules are interconnected by an electronic ring break diagnostics line. This line is only required for electronic ring break diagnostics in the event of a fault.38Ring break diagnosticsThe ring break diagnosis line is, as the name suggests, only required for diagnostics after loss of MOST communication.A ring brake diagnosis line is not relevant for data transfer between the control modules.Digital Sound System Control Module J525DVD Changer R161Information Electronics Control Module 1 J794Windshield Projection Head Up Display Control Module J898664_099Instrument Cluster Control Module J285Key: MOST Ring break diagnosis lineOptical replacement control unit VAS 6778Diagnostics The ring break diagnosis procedure is identical to that of the previous MOST bus system. Diagnostic information is retrieved via Address Word 5F using the VAS Scan Tool. Even though the ring break diagnosis procedure remains unchanged, a modified tool – the optical replacement control unit VAS 6778 – must be used in the event of an optical fault in the MOST150 bus, due to the modified transmitter and receiver units in the control modules.664_100Reference For further information on the MOST bus, refer to eSelf-Study Program 971303 Audi New Data Bus System – LIN, MOST, BluetoothTM.39Control modulesData Bus on Board Diagnostic Interface J533Brief descriptionIt is located at the center of the new Audi A8 beneath the rear bench seat. It can still be accessed with the via Address Word 19 using the VAS Scan Tool. The gateway performs the following functions: ›› ›› ›› ›› Network system gateway. Controller for FlexRay bus. Diagnostics master. Energy manager for low-voltage electrical system (12 volts). ›› Energy manager for medium-voltage electrical system (48 volts). ›› Interface for various connect services. Special feature: ›› The gateway manages the diagnostic firewall featured in the new Audi A8 for the first time. It is a user of the following data bus systems: ›› Hybrid CAN. ›› Comfort/convenience systems CAN. ›› Comfort/convenience systems CAN 2. ›› Infotainment CAN. ›› Instrument panel insert CAN. ›› Extended CAN. ›› FlexRay. ›› Diagnostics CAN. ›› Ethernet. It is not a user of: ›› Modular Infotainment Matrix (MIB) CAN. ›› MOST bus. It is the LIN master for: ›› Battery Monitoring Control Module J367. ›› for alternator C (with 12-volt generator). ›› for Multifunction Steering Wheel Control Module J453.664_040Data Bus on Board Diagnostic Interface J53340Diagnostic firewallThe diagnostic firewall is a new safety function of the Data Bus on Board Diagnostic Interface J533. It prevents unauthorized access to sensitive vehicle data during vehicle operation. J533 contains a "White List" which determines which service is permitted access when the diagnostic firewall active. As a basic principle, all read services are enabled and all write services are disabled. The diagnostic firewall is activated for the first time when the vehicle has covered a distance of more than 124.2 miles (200 km). This function will be used in other Audi models at a future date.Diagnostic firewallSchematic diagram of diagnostic firewallDiagnostic connectorData Bus on Board Diagnostic Interface J533Control unit 1Control unit 2Control unit 3Control unit 4Control unit 5Control unit 6Control unit 7Control unit 8664_047White list: ›› ›› ›› ›› ›› ›› ›› Accessing the diagnostics. Read event memory. Read measured data. Read identication data. Clear event memory. Activate / deactivate Transport mode. All services in the gateway.Disabled services: ›› ›› ›› ›› Activate control elements. Carry out basic setting. Replace control module. Check SVM control module configuration.The diagnostic firewall is deactivated 1 2 3 When the hood is opened If there is no communication with the Vehicle Electrical System Control Module J519 (BCM1 timeout) When a crash signal is received from Airbag Control Module J234The diagnostic firewall is reactivated When the vehicle travels a distance of greater than 12.4 miles (20 km) with the hood closed The diagnostic firewall is reactivated when the signals are present again. The diagnostic firewall is reactivated when transmission of the crash signal stopsWhen the diagnostics are accessed with the VAS Scan Tool, the user is informed that the diagnostic firewall is active. The following message appears on the diagnostic tester display:NoteThe status of the diagnostic firewall can be seen via the Data Bus on Board Diagnostic Interface J533.The diagnostic firewallis currently active. It is recommended that the diagnostic fire wall be deactivated. Open the hood. Status of diagnostic firewall: activeResume664_16641DoIP - Diagnostics over Internet ProtocolDiagnose via CAN Because the CAN bus was previously used for vehicle diagnostics, the speed at which the data could be transmitted across the gateway to the control modules in a vehicle was limited to a maximum of 1 Mbit/s. The CAN technology does not allow data to be transferred at a faster rate than this. This meant that the speed of the FlexRay (10 Mbit/s) could not be fully utilized for diagnostics or software updates.Control module 1Control module 2Control module 3FlexRay 10 MBit/s Control module 4 Control module 5 Control module 6Diagnostics CAN 1 MBit/sExtended CAN 500 kbit/s Control module 7 Control module 8 Control module 9Comfort/convenience systems CAN 500 kbit/s664_042Diagnostics via CAN and DoIP With the additional Ethernet connection, it is now possible to utilize the full bandwidth of the FlexRay. This is especially advantageous when parameterizing engine and transmission control modules. Furthermore, it is now also possible to parameterise CAN control modules in parallel. To utilize the Ethernet connection, you must use data interface VAS 6154, which is equipped with WiFi technology. The additional wires required for the diagnostic tester hardware have been installed since the launch of the 2017 Audi Q7 (the first representative of the MLBevo series). The wires connected to the Data Link Connector have the same color and cross-section as the FlexRay lines, but serve as an Ethernet connection.Control module 1Control module 2Control module 3FlexRay 10 MBit/s Control module 4 Diagnostics CAN 1 MBit/s Extended CAN 500 kbit/s Control module 7 Control module 8 Control module 9 Control module 5 Control module 6FlexRay 100 MBit/sComfort/convenience systems CAN 500 kbit/s664_04342Selective partial network operationRationale The demand for electrical power in the modern automobile is constantly increasing due to the increasing number of electronic control modules. To reduce this need for power, many electrical systems are being configured to operate according to requirement. That is, they are only utilized when needed. Until now, all control modules have been active (awake) during vehicle operation. The have also participated in bus communications and consumed electrical power by constantly running in stand-by mode. In the future, it will be possible to group together different control modules to build various partial networks irrespective of the bus system to which they are connected. The modules in these partial networks can be activated and de-activated as required. This saves electrical power. To do this, the control modules require intelligent transceivers which do not activate the module until a relevant message is received. In the 2019 A8, ten control modules are configured for partial network operation.Without partial network operationWith partial network operationGatewayGateway664_044664_045Key: Continuous operation Partial network 1 Partial network 2 Partial network 3 Partial network 4 Partial network 543Frame Detect capabilityControl modules in network topologies without selective partial network operation know only two states. ›› Bus idle - the control module is also inactive. ›› Data bus active - the control module is running and consuming electrical power.In networks with partial network operation, selected control modules are equipped with a transceiver which has a Frame Detect Mode, that is, the control module can assume a third state. ›› Data bus active - but the control module is still inactive because the transceiver has not yet recognized a wake-up message (i.e. it has not yet detected a data frame which causes it to wake up the control module).Bus idle Without partial network operationFrame Detect modeData bus activeU / volts Micro ControllerU / volts Micro ControllerData busData bus›› Bus communication: Off ›› Transceiver: Sleep mode ›› Control module: "Sleeping"With partial network operation›› Bus communication: On ›› Transceiver: Active ›› Control module: "Awake"U / volts Micro ControllerU / volts Frame Detect Transceiver: Micro ControllerU / volts Frame Detect Transceiver: Micro ControllerData busFrame Detect Transceiver:Data busData bus›› ›› ›› ››Bus communication: Off Transceiver: Sleep mode Frame Detect function: Off Control module: "Sleeping"›› ›› ›› ››Bus communication: On Transceiver: Standby mode Frame Detect function: On Control module: "Sleeping"›› ›› ›› ››Bus communication: On Transceiver: Active Wake-up message detected Control module: "Awake"Service Selective partial network operation does not affect vehicle repair procedures. When the diagnostics are accessed, all control modules are woken up. This facilitates communication between the Scan Tool and the control module.44Vehicle Electrical System Control Module J519 (BCM1)The Vehicle Electrical System Control Module J519 is one of the central modules whose functions have been expanded successively in recent years. In addition to typical tasks such as reading in numerous sensors and activating actuators of the external lighting and wiper control system, a number of integration functions such as park assist or seat heater activation are now implemented in J519. As noted earlier, J519 is now the control module for the climate control system. All diagnostic functions for the climate control system are also performed by J519. It is installed on left hand side of the vehicle under the instrument panel.Vehicle Electrical System Control Module J519664_101664_14645Brief descriptionDesignation Equipment Installation location TasksVehicle Electrical System Control Module J519 / also referred to as BCM1 (Body Control Module 1) Always installed Below the instrument panel on the left-hand side of the vehicle (installation location is always on the L/H side, even in RHD models) Exterior lighting master Interior lighting master Diagnostic gateway for the light control modules Interface for various connect services Integration functions ›› Parking • Parking aid • Park assist steering ›› Background lighting • Activation of the interior light modules ›› Climate controlAddress Word Data bus communication0009 ›› Comfort/convenience systems CAN 2 user ›› J519 is the LIN master for • LIN 1: Light Switch E1, Rain/Light Recognition Sensor G397 and Humidity Sensor G355, Wiper Motor Control Module J400, Windshield Washer Pump Control Module J1100 • LIN 2: Garage Door Opener Control Module J530, Automatic Dimming Interior Rearview Mirror Y7, Roof Electronics Control Module J528, Rear Interior Lamp WX2 • LIN 3: Power Adjustable Steering Column Control Module J866, Driver Seat Backrest Blower Fan V388, Driver Seat Cushion Blower Fan V390, Front Passenger Seat Backrest Blower Fan V389, Front Passenger Seat Cushion Blower Fan V391 • LIN 4: Switch Module in Instrument Panel, Center EX22, Center Console Switch Module 1 EX23 • LIN 5: Interior light modules 1 - 15 • LIN 6: Interior light modules 16 - 30 • LIN 7: Interior light modules 31 - 45 • LIN 8: Heating control (4 pcs), Left Rear Backrest Fan 1 1 V520, Left Rear Seat Cushion Fan 1 V522, Right Rear Backrest Fan 1 V524, Right Rear Seat Cushion Fan 1 V526, Rear A/C Display Control Head E265 • LIN 9: Servomotors (15 pcs) • LIN 10: Fresh Air Blower Control Mod