TECHNICAL DOCUMENTATION
SSP 970343 – The 2015 Audi A3 Vehicle Electronics and Driver Assistance Systems

This PDF is currently unavailable.
Read document text
eSelf Study Program 970343The 2015 Audi A3 Vehicle Electronics and Driver Assistance Systems2Audi of America, LLC Service Training Created in the U.S.A. Created 11/2013 Course Number 970343 ©2013 Audi of America, LLC All rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC. Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.Revision 3 1: 11/2013ContentsIntroduction........................................................................................ 6Topology the 2015 Audi A3 ..................................................................................................................7Vehicle electronics............................................................................... 9Door electronics ...................................................................................................................................11 Vehicle Electrical System Control Module J519 ................................................................................16 Electronic Steering Column Lock Control Module J764 ....................................................................20 Access/Start Authorization Control Module J518 .............................................................................21 Advanced Key .......................................................................................................................................22 Terminal management ........................................................................................................................25 Interior lighting ...................................................................................................................................29Driver assistance systems..................................................................34Rearview Camera R189 .......................................................................................................................34 Audi parking system ............................................................................................................................36 Audi side assist ....................................................................................................................................37 Driver Assistance Systems Front Camera R242 ................................................................................39Audi lane assist and active lane assist...............................................41Overview ...............................................................................................................................................41 Further development ..........................................................................................................................41 Active lane assist .................................................................................................................................42 Audi steering intervention ..................................................................................................................43 Operation ..............................................................................................................................................44Self Study Programs..........................................................................45 Knowledge Assessment....................................................................464This eSelf Study Program teaches a basic knowledge of the design and functions of new models, new automotive components or technologies. It is not a Repair Manual! All values given are intended as a guideline only. For maintenance and repair work, always refer to the current technical literature.NoteReference5IntroductionToday, Audi is already setting new standards for driver assistance systems in the A3 – introducing technologies from the luxury class into the premium compact segment. Several optional systems and one standard solution are offered in the new 2015 Audi. The optional Audi side assist supports the driver in changing lanes. From a vehicle speed of 18 mph (30 km/h ), radar sensors at the rear monitor what is happening behind and to the sides of the A3. A yellow LED in the door mirror housing lights if another vehicle is driving in the blind spot or is rapidly approaching from the rear. If the driver still activates the turn signal for a lane change, the indicator turns bright and flashes at a high frequency – a very effective warning signal. Audi active lane assist becomes active at a speed of 40 mph (65 km/h). It detects lane markings on the roadway based on images from a small video camera mounted on the rear-view mirror. If the vehicle approaches a lane marking without activating the turn signal, the system assists the driver in steering back into the lane by making a slight intervention in the electromechanical power steering system. Of the optional driver assistance systems in the new A3, adaptive cruise control (ACC) is the most complex. This radar-based system maintains the desired distance to the vehicle ahead by autonomously accelerating and braking within certain limits over speeds ranging from 18 – 93 mph (30 to 150 km/h). The driver can set the distance and the control dynamics over four levels. If the car has the assistance package, which combines several systems, the control range is extended to 125 mph (200 km/h). In the North American region vehicles, the system intervenes just before crossing over a detected lane marking. This function can help to prevent the car from leaving the driving lane unintentionally, for example, due to driver inattentiveness. This new generation of lane-keeping assistance can offer continuous relief to the driver, enhancing driving comfort.611_001a6Topology the 2015 Audi A3The topology shows all control modules with connectivity to the data bus system. Some of the control modules shown here are optional, country-specific equipment, or will be introduced at a later date. Be aware that all the modules shown will not be installed on every vehicle.Light switch E1 Headlight power module, left J667Power Sunroof Control Module J245Wiper motor control unit J400Headlight power module, right J668Anti-theft Alarm System Sensor G578Rain/Light Recognition Sensor G397Humidity sensor G355Power output module for left LED headlightAlarm horn H12Vehicle Electrical System Control Module J519 Instrument Cluster Control Module J285Power output module for right LED headlightLane Change Assistance Control Module 2 J770Steering Column Electronics Control Module J527 Driver Side Rear Door Control Module J926Data Link Connector Multifunction steering wheel control unit J453Driver Door Control Module J386Passenger Side Rear Door Control Module J927Front Passenger Door Control Module J387Data Bus Onboard Diagnostic Interface J533Nox Sensor Control Module J583* Engine Control Module J623Access/Start Authorization Control Module J518 Electrical Steering Column Lock Control Module J764Nox Sensor Control Module 2 J881*Passenger Occupant Detection System Control Module J706 Left Front Seat Belt Tensioner Control Module J854 Right Front Seat Belt Tensioner Control Module J855Airbag Control Module J234Climatronic Control Module J255DSG Transmission Mechatronic J743Selector Lever Sensor System Control Module J587 Fresh Air Blower Control Module J126 Refrigerant Circuit Pressure Sensor G805 Humidity Sensor in Fresh Air Intake Duct G657 Air quality sensor G238*2.0L TDI engine only7For example, Cornering Lamp and Headlight Range Control Module J745 would never be installed on the same vehicle as Headlamp Range Control Module J431.Headlamp Range Control Module J431Cornering Lamp and Headlight Range Control Module J745Multimedia System Control Head E380Lane Change Assistance Control Module J769 Driver Assistance Systems Front Camera J842 Distance Regulation Control Module J428Front Information Display Control Head J685Digital Sound System Control Module J525Information Electronics Control Module 1 J794 ABS/ESP Control Module J104 Battery Monitoring Control Module J367Power Steering Control Module J500Alternator CAll Wheel Drive Control Module J492Rearview Camera System Control Module J772Electronic Damping Control Module J250610_001_pkdKey: Powertrain CAN bus Convenience CAN bus Extended CAN bus Infotainment CAN bus Diagnostics CAN bus Suspension CAN bus LIN bus Sub-bus systems MOST bus8Vehicle electronicsInstrument Cluster Control Module J285Instrument cluster with monochrome Driver Information System The monochrome Driver Information System has a resolution of 320 x 240 pixels.611_003aThe process for navigating through the various menus is the same as that of the A6, A7, and A8 models.Instrument cluster with color Driver Information SystemThe color display also has a resolution of 320 x 240 pixels. Any vehicle with ACC will also have this type of instrument cluster.9611_003aInstrument cluster electrical connectionsA fused terminal 30 wire and discrete terminal 31 wire are routed to Instrument Cluster Control Module J285. The module communicates with other modules via two twisted CAN bus wires over the Convenience CAN. In addition, J285 reads the signals from two fuel tank senders and the Immobilizer Coil D2. The fuel senders use three-wire technology. (Only quattro modules have two fuel senders.) On vehicles without Advanced key, Immobilizer Coil D2 is located around the ignition switch and exchanges data with the key when it is inserted. In vehicles with Advanced key, Immobilizer coil D2 is located in the approximate area where the ignition switch would be. The position is marked for identification in case an emergency start must be performed.Terminal 30Convenience CAN HighConvenience CAN LowAnti-theft Immobilizer Reader Coil D2Instrument Cluster Control Module J285Fuel tank sender 1Fuel tank sender 2611_005Immobilizer master functionInstrument Cluster Control Module J285 is the master module for the immobilizer system. The following control modules have immobilizer functions: • • • Engine Control Module J623 Electronic Steering Column Lock Control Module J764 DSG Transmission Mechatronic J74310Door electronicsDriver Door Control Module J386Installation location611_006Tasks and characteristics of the control module• Convenience CAN participant • LIN bus master for Driver Side Rear Door Control Module • Monitoring the central power window button status • Monitoring the door contact switch, the central locking button and child lock button status • Monitoring the mirror adjustment switch and anti-theft alarm deactivation button status • Monitoring the status of the micro-switch in the driver door locking unit • Activating the window motor and the mirror adjustment motors • Activating the locking and SAFE motor in the driver door locking unit* • Activating the door mirror heater • Substitute master for the central locking system • Activating the indicator in the door mirror and the lights of the optional interior light package* Not used in the North American region11Pin assignments Driver Door Control Module J386Power supplyTerminal 30 B19 Terminal 31 B20 Ground circuit "Terminal 30" supply; protected by a 30A fuseOther supply voltages C3 C4 C14 D5 Voltage supply circuit for mirror heater and indicator in door mirror Ground circuit of mirror adjustment potentiometer Voltage supply of mirror adjustment potentiometer Ground line of driver door buttonBus linesCAN bus B14 B15 LIN bus B10 LIN bus to door electronics in driver side rear door Convenience CAN Low Convenience CAN HighInputsSwitch B5 D24 D25 Button D20 D23 D27 D28 D29 D30 D31 D32 Signals B1 B6 B7 B8 B17 C13 C16 Driver Lock Cylinder Contact Switch F241 Driver door microswitch locked / SAFE* Ground circuit of microswitch in driver door locking unit Input signal for door mirror dimming function Input signal for door mirror dimming function Voltage signal of the horizontal mirror adjustment potentiometer, driver side Voltage signal of the vertical mirror adjustment potentiometer, driver side Alarm System Deactivation Switch E217 Rear Lid Remote Release Button E233 Child Safety Lock Button E318 Driver Interior Locking Switch E150 Passenger Side Rear Power Window Button in Driver Door E714 Driver Side Rear Power Window Button in Driver Door E712 Front Passenger Power Window Button in Driver Door E715 Driver Power Window Button E710 Driver Door Contact Switch F2 Mirror Adjusting Switch E43 Mirror Selector Switch E48* Not used in the North American region12OutputsLights B3 C1 C11 D1 D3 D4 D16 Lamp for Driver Side Door Speaker Trim L223 Ambient light in door mirror Driver Exterior Rearview Mirror Turn Signal bulb L131 Central Locking -Safe- Indicator Lamp K133 Passenger Side Interior Door Handle Illumination Lamp L220 Driver door button locating light - terminal 58xs Front door warning light, driver side W30 and front left entry light W31Function LEDs in buttons D10 D11 D12 D13 Motors Function light in anti-theft alarm button Function light in rear right electrical child lock* Function light in rear left electrical child lock* Function light in interior locking button, driver sideA3 A6 B11 B12 B13 C5 C7 C8 C9 C10 Driver Window Regulator Motor V142 Driver Window Regulator Motor V142 Ground of SAFE function and central locking motors in the driver door locking unit* Driver Door Central Locking -SAFE- Motor V161* Driver Door Central Locking System Motor V56* Shared connection of both mirror adjustment motors V17 and V149 Driver Mirror Adjustment Motor V17 Driver Mirror Adjustment Motor Driver Exterior Rearview Mirror Folding Motor V121 Driver Exterior Rearview Mirror Folding Motor V121Other actuators C2 C6 C15 Output signal for door mirror dimming function Output signal for door mirror dimming function Heated Driver Exterior Rearview Mirror Z4* Not used in the North American region13Driver Side Front and Rear Door Control Modules J386 and J926Some component designations for service will be updated with the introduction of the 2015 Audi A3. The designations will include information on locations and will be written in a more clear manner. Such terms as “rear left” or “rear right” will be replaced with descriptions such as “rear driver side” and “rear passenger” side. The rear door control modules for the 2015 A3 have new designations as well as being new in design. These door control modules will be installed in all five door iterations of the Audi A3 model for North America. This version provides a locking and unlocking button in the door.Tasks of J386 and 926• Communicating with the corresponding front door control module via LIN bus Self-diagnosis and the transfer of diagnostic information Monitoring the door contact switch, the window regulator button and the central locking button Activating the lights for the optional interior light package Activating the window regulator motor, locking and SAFE motor and the child lock motor*• • • • Terminal 30 Driver’s Door Control Module J386 V471 30A L225 W83 W90Driver Side Rear Door Control Module J926F435V539V537V535V505E717E711KeyE711 E717 F435 F505 J386 J926 L225 Driver Side Rear Power Window Button Driver Side Rear Interior Locking Button Driver Side Rear Central Locking Unit Driver Side Rear Door Contact Switch Driver Door Control Module Driver Side Rear Door Control Module Lamp for Driver Side Rear Door Speaker Trim V471 V535 V537 V539 W83 W90 Driver Side Rear Window Regulator Motor Driver Side Rear Child Safety Lock Motor Driver Side Rear Central Locking –SAFE– motor Driver Side Rear Central Locking System Motor Driver Side Rear Entry Lamp Driver Side Rear Door Warning lamp* SAFE and Child lock motor not used in the North American region14Pin assignments Driver Side Rear Door Control Module J926Power supplyTerminal 30 B19 Terminal 31 B20 C13 Ground circuit Ground circuit of the rear door button, driver side "Terminal 30" supply; protected by a 30A fuseBus linesLIN bus B10 LIN bus to Driver Door Control Module J386InputsSwitches and buttons B5 C9 C10 Signals B4 B6 B7 Child lock microswitch, rear driver side activated / deactivated* Rear door microswitch, rear driver side locked / SAFE* Ground circuit of microswitch in locking unit, rear driver side Driver Side Rear Door Contact Switch F505 Driver Side Rear Power Window Button E711 Driver Side Rear Interior Locking Button E717OutputsLights C1 C2 C11 C12 Motors A3 A6 B9 B11 B12 B13 Driver Side Rear Window Regulator Motor V471 Driver Side Rear Window Regulator Motor V471 Driver Side Rear Child Safety Lock Motor V535* Ground for central locking motors in the door locking unit, rear driver side Central locking SAFE function Driver Side Rear Door Central Locking -SAFE- Motor V537* Driver Side Rear Central Locking System Motor V539 Lamp for Driver Side Rear Door Speaker Trim L225 Rear door button locating light, driver side - terminal 58xs Function light in rear interior locking button, driver side Door warning light, Driver Side Rear Door Warning Lamp W90, Driver Side Rear Entry Lamp W83* SAFE and Child lock motor not used in the North American region15Vehicle Electrical System Control Module J519Installation location611_010Tasks and characteristics of J519• Communicating with other control modules via the convenience CAN bus • LIN bus master for multiple LIN bus systems • Central locking system master • Exterior light master; activation of front headlights and tail lights • Interior light master; generation of terminals 58xs, 58xt and 58xd (locating light) • Activating the windshield washer and head light washer (if equipped) pumps • Monitoring the signals of various switches and buttons • Monitoring the ambient temperature sensor and the seat heater temperature sensors • Activating the "terminal 15" relay, rear window heater relay and horn relay • Activating the driver and front passenger seat heaters as well as the heated windshield washer spray jets.16Vehicle Electrical System Control Module J519Power supplyTerminal 30A1 A66 A73 C1 C12 C73 "Terminal 30" supply; protected by a 30A fuse "Terminal 30" supply; protected by a 40A fuse "Terminal 30" supply; protected by a 40A fuse "Terminal 30" supply; protected by a 40A fuse Switched "terminal 30" "Terminal 30" supply; protected by a 30A fuseGround lines A12 A63 C63 Vehicle ground - "terminal 31" Vehicle ground - "terminal 31" Vehicle ground - "terminal 31"Bus linesCAN bus A16 A17 LIN bus A15 B30/C28 B31 LIN bus line to Anti-theft Alarm System Sensor G578, Power Sunroof Control Module J245 (LIN bus 3) LIN bus line to Wiper Motor Control Module J400, Power Sunroof Control Module J245, Rain/Light Recognition Sensor G397 (LIN bus 1) LIN bus line to Alarm Horn H12 (LIN bus 2) Convenience CAN High Convenience CAN LowInputsSwitchA29 A33 A35 A48 A50 A52 A53 B11 B13 B14 B16 B19 B28 C58 Redundancy line to Light Switch E1 Rear door microswitch, passenger side locked / SAFE* Rear door microswitch, rear driver side locked / SAFE* Passenger Side Rear Door Contact Switch F506 Driver Side Rear Door Contact Switch F505 Microswitch for fully closed position of door lock mechanism (rear trunk lock) Microswitch for partially closed position of door lock mechanism (rear trunk lock) Open Brake Fluid Level Warning Switch F34 Engine Hood Contact Switch F266 and Hood Contact Switch 2 F329 Engine Coolant Level Sensor G32 Ground circuit for various level sensors Windshield Washer Fluid Level Sensor G33 Brake Light Switch FButtonA32 C34 C42 Rear Lid Lock Cylinder Unlock Button F248 (soft touch) Driving Profile Selection Switch Module E592 Emergency Flasher Button E229* SAFE and Child lock motor not used in the North American region17Sensors B12 B27 C40 C43 C56 Signals A44 A47 A51 A54 C14 "Terminal 15" request 1; supplied by Electronic Steering Column Lock Control Module J764 if the vehicle is equipped with the optional advanced key, otherwise by Electronic Steering Column Lock Control Module J527 "Terminal 15" request 2; supplied by the Electronic Steering Column Lock Control Module J764 J764 if the vehicle is equipped with the optional advanced key, otherwise by Electronic Steering Column Lock Control Module J527 Open "NO contact" signal; supplied by Steering Column Electronics Control Module J527 if the vehicle is not equipped with the optional advanced key, otherwise by Electronic Steering Column Lock Control Module J764 if the vehicle is equipped with the optional advanced key Wake-up signal of Access/Start Authorization Control Module J518 Right Front Brake Pad Wear Sensor G35 Ambient Temperature Sensor G17 Right Front Seat Temperature Sensor G345 Left Front Seat Temperature Sensor G344 Ground circuit to both front seat temperature sensorsOutputsRelays A13 B24 C24 Activation of Terminal 15 Power Supply Relay J329 Activation of Horn Relay J413 Activation of Rear Window Defogger Relay J9Lights in vehicle interior C21 C48 C51 C62 C72 Tail lights Function light in driving profile selection button (Drive Select) Emergency Flasher Indicator Lamp K6 Open Power supply to locating light terminal 58xs Activation of Front Left and Right Footwell Lamps L151 and L152; Rear Left and Right Footwell Lamps L106 and L107A57 A59 A60 A64 A65 A71 A72 C3 C6 C8 C9 C10 C11 C31 High Mounted Brake Lamp Left and Right License Plate LEDs X4 and X5 Left Brake /Turn Signal Lamp M56 Right Back-up Lamp Bulb M17 (rear lid light) Right Tail Lamp Bulb M38 (rear lid light) Open Left Rear Fog Lamp Bulb L46 (rear lid light in comb. with LED tail light) Right Brake Lamp/Turn Signal Bulb 2 (rear lid light in comb. with LED tail light) Right Rear Fog Lamp Bulb L47 (rear lid light in comb. with LED tail light) Open Left Brake Lamp/Turn Signal Bulb 2 M84 (rear lid light in comb. with LED tail light) Left Rear Side Marker Lamp M37 Left Back-up Lamp Bulb M16 (rear lid light) Right Brake Lamp/Turn Signal Bulb (side light)18HeadlightsB1 B2 B4 B5 B10 B20 B21 B22 B23 B32 B36 B39 B45 C5 Open Open Left Daytime Running Lamp and Position Lamp Control Module J860 (with bi-xenon lights) Open Left Daytime Running Lamp and Position Lamp Control Module J860 (with bi-xenon lights) Right Front Turn Signal Bulb M7 Right Daytime Running Lamp and Position Lamp Control Module J861 (with bi-xenon lights) Right Low Beam Headlamp Reflector Motor V295 (with bi-xenon lights without AFS) Left Low Beam Headlamp Reflector Motor V294 (with bi-xenon lights without AFS) Right Daytime Running Lamp and Position Lamp Control Module J861 (with bi-xenon lights) Left Front Turn Signal Bulb M5 Open Open OpenMotorsA3 A4 A6 A7 A9 A36 A37 A68 A69 Open Open Ground of SAFE function and central locking motors in the door locking unit, rear passenger side* Passenger Side Rear Central Locking System Motor V540 Rear Lid Central Locking System Motor V53 Driver Side Rear Door Central Locking -SAFE- Motor V537 Passenger Side Rear Door Cental Locking - SAFE- Motor V538* Ground of SAFE function and central locking motors in the door locking unit, rear driver side Driver Side Rear Central Locking System Motor V539Other actuatorsA2 A5 B7 / A61 B8 / A62 B9 B46 Driver Seat Heating Element Z6, Driver Backrest Heating Element Z7 Passenger Seat Heating Element Z8, Passenger Backrest Heating Element Z9 Control line for washer pump V5 and rear window wiper motor V12 Open Left and Right Washer Nozzle Heaters Z20 and Z21 Headlamp Washer Pump V11Signal linesA14 C67 "Terminal 15" signal for various control module Door contact signal for interior light control on overhead module* Not used in the North American region19Electronic Steering Column Lock Control Module J764Only installed with the Advanced key option.Installation location611_012Tasks and characteristics of the control module • Communicating with other control modules via the Convenience CAN bus • Locking and unlocking the steering column • Terminal management master • Monitoring the signal from Access/Start Authorization Button E408 • Immobilizer participant Locking the steering column Locking of the steering column can be initiated by the following two events: • Opening the driver's door or • Locking the vehicle with the remote control key, the Advanced key or the door lockUnlocking the steering column The steering column is unlocked after actuating Access/ Start Authorization Button E408 if a key belonging to the vehicle has been detected inside the vehicle. After unlocking the steering column, the NO contact and terminal 15 are activated and terminal 50 is requested.The steering column is only locked if all of the following conditions have been met: • • • • • The steering column is unlocked The vehicle is travelling at speed of 0 mph (0 km/h) The engine is not running Terminal 15 and the NO contact have been deactivated The selector lever is in position “P”!Note The steering column lock is still implemented mechanically on models ordered without the optional Advanced key. In these models, the terminals are managed by Electronic Steering Column Lock Control Module J527.20Access/Start Authorization Control Module J518J518 is only installed on vehicles with Advanced key.Installation location611_013Tasks and characteristics of the control module • Communicating with other control modules via the convenience CAN bus • Activating the five antennas for entry and start authorization • Monitoring both capacitive sensors in the driver and passenger door handles • Activating the locating light in Access/Start Authorization Button E408 • Waking up Vehicle Electrical System Control Module J519 via a wake-up line after contact with the door handle sensors is detected21Advanced KeyThe optional Audi advanced key is available for the first time on an A3 model with the introduction of the 2015 A3 sedan. If Advanced key has been installed in the vehicle, it has the following additional control modules: • Access/Start Authorization Control Module J518 and • Electronic Steering Column Lock Control Module J764Terminal 30 Terminal 30Access/Start Authorization Control Module J518Electronic Steering Column Lock Control Module J764"Terminal 15" - signal 1 "Terminal 15" - signal 2"Wake up" lineVehicle Electrical System Control Module J519NO contactInternal antenna for central central locking systemEngine Control Module J623611_015Key:E408 G415 G416 R134 R135 R136 R137 R138 Access/Start Authorization Button Driver Exterior Door Handle Touch Sensor Passenger Exterior Door Handle Touch Sensor Driver Access/Start System Antenna Front Passenger Access/Start System Antenna Access/Start System Antenna in Rear Bumper Access/Start System Antenna in Luggage Compartment Access/Start System Antenna 1 in Vehicle InteriorTerminal 50 requestConvenience CAN busGear selector lever position "P"Terminal 58xt22Access/Start Authorization antennasAll five Access/Start System antennas are activated by Vehicle Electrical System Control Module J519. They are installed in the following positions:611_016611_019Driver Access/Start System Antenna R134. On body under ‘B’ pillar area.Access/Start Antenna in Luggage Compartment R137. Located under seat.611_017611_020Front Passenger Access/Start Antenna R135. On body under ‘B’ pillar area.Access/Start System Antenna 1 in Interior R138.611_018Access/Start System Antenna in Rear Bumper R136.23Unlocking/locking a vehicle with Audi advanced keyAccess/Start Control Module J518 monitors Driver Exterior Door Handle Touch Sensors G415 and G416. Unlocking and locking input can be sent to the Advance key system via these sensors. The sensors are located in the driver and front passenger door handles. No door handle sensors are installed on the rear doors. To unlock the vehicle, the driver or passenger must grip the respective door handle. To lock the vehicle, contact must be made with the marked surface (framed rectangle) on the door handle. After the system has detected an unlocking or locking input, a scan of the ignition key is initiated. The system activates the five antennas and receives a reply form the vehicle key via the central locking antenna. The system uses this reply to check whether the key is authorized and within the radius of the operating point. If all the conditions are met, Vehicle Electrical System Control Module J519 initiates the corresponding operation. J519 transfers the unlock or lock commands to the Convenience CAN bus. The commands are received by door control modules and subsequently unlock or lock the doors.Switching the ignition onTo switch the ignition on, Access/Start Authorization Button E408 must be pressed. If all the condition for switching on the ignition are met, the system first unlocks the steering column. After the column is unlocked, Terminal 15 Power Supply Relay J329 is activated and the ignition is switched on. If the conditions for starting the engine have been met during this process, Engine Control Module J623 activates both starter relays. The starter is energized, the fuel injection cycle begins and the engine starts.24Terminal managementTerminal management without Audi advanced keyTerminal management functionality depends on whether the 2015 A3 is equipped with the optional Advanced key system or not. On models without the Advanced key system, Steering Column Electronics Control Module J527 is the terminal management master. On models with Advanced key, this task is performed by Steering Column Electronics Control Module J764.Terminal management without Audi advanced keyTerminal 30 Gear selector position "P"Convenience CAN busSteering column switch moduleIgnition starter switchIgnition key removal lockSteering Column Electronics Control Module J527Terminal 15 request 1 Terminal 15 request 2 NO contactVehicle Electrical System Control Module J519Terminal 30Powertrain CAN busEngine Control Module J623Terminal 50 diagnostics Terminal 50Terminal 50 requestTerminal 15Terminal 15611_022Key:J329 J906 J907 Terminal 15 Power Supply Relay Starter relay 1 Starter relay 225Steering column switch moduleThe ignition key removal lock, ignition switch and Steering Column Electronics Control Module J527 are all components of the steering column switch module. J527 monitors the ignition switch continuously and activates the ignition key removal lock as required.Terminal 15The task of Steering Column Electronics Control Module J527 (terminal management master) is to determine the status of terminal 15. To do this it monitors the status of the NO contact and both ‘terminal 15 request’ sensors. However, it is the task of Vehicle Electrical System Control Module J519 to activate the terminal 15 voltage supply relay. To do this, J519 monitors the following three signals:Generating the individual terminal status signalsTo generate the various terminal status signals, J527 continuously monitors the sensors in the ignition switch. The switch has four sensors: • • • • NO contact sensor Terminal 15 request sensor 1 Terminal 15 request sensor 2 Terminal 50 request sensor• Terminal 15 request 1 • Terminal 15 request 2 • NO contact The information is transferred by J527 and reflects the status of the three sensors in the ignition switch. If voltage is measured in two of the three signals wires from Vehicle Electrical System Control Module J519, Terminal 15 Relay J329 is activated and the ignition is switched on. With this configuration, it is still possible to start the vehicle even if a fault occurs in one of the three sensors in the ignition switch.J527 continuously generates the current status signals for terminals 15, 50 and 75 on the NO contact based on the input from the sensors. The current terminal status is transmitted to other control modules through the Convenience CAN bus.Terminal 50The Engine Control Module receives the requests to start the engine from J527. This request is sent both by discrete wires and via the CAN bus. The Engine Control Module activates both starter relays J906 and J907. To this end, the ECM closes internal switches and connects both relays to ground. The relays then close their switching contacts and terminal 50 is supplied to the starter. A protected diagnostic line allows the Engine Control Module to check whether terminal 50 has actually been switched.NO contactThe NO contact is activated by inserting the vehicle key into the ignition switch. When this is detected, J527 transfers the information ‘NO contact on’ to the CAN bus and to Vehicle Electrical System Control Module J519 by a discreet wire. There is no ‘NO contact’ wire for supplying consumers. The NO contact is deactivated by removing the ignition key from the switch.Terminal 75No separate terminal 75 relay is installed in the 2015 Audi A3. Other control modules receive the current status of terminal 75 from Steering Column Electronics Control Module J527.26Terminal management with Audi advanced keyJ518Terminal 30E408Gear selector position "P"10AConvenience CAN busSteering Column Electronics Control Module J764Terminal 15 request 1 Terminal 15 request 2 NO contactVehicle Electrical System Control Module J519Terminal 30Terminal 50 requestTerminal 15Terminal 15Powertrain CAN busEngine Control Module J623Terminal 50 diagnostics Terminal 50611_023Key:E408 J329 J906 J907 Access/Start Authorization Button Terminal 15 Power Supply Relay Starter relay 1 Starter relay 227Steering Column Electronics Control Module J764When the vehicle has Audi advanced key, Access/Start Authorization Button E408 is installed in place of the ignition switch. The ignition is switched on and off and the engine started or switched off with this button.Terminal 50The Engine Control Module receives the request to start from J764. The request is sent across discrete wires as well as on the Convenience CAN bus. The ECM activates both Starter Relays J906 and J907. To do this, the ECM closes its internal switches and connects both relays to ground. Both relays then close their switching contacts and terminal 50 is available to the starter. A protected diagnostic wire allows the ECM to check whether terminal 50 has been switched.Access/Start Authorization Button E408E408 has two micro-switches. Both are monitored by Steering Column Electronics Control Module J764. The microswitches are actuated as long as the button is pressed. J764 determines the current status of terminals 15, 50, 75 and the NO contact by continuously monitoring the microswitches. The status of these terminals is transmitted to other control modules over the Convenience CAN bus. If either of the micro-switches in E408 becomes faulty, the ignition can no longer be switched on nor the vehicle engine started. If this occurs while the ignition is switched on and the engine running, it can be switched off one more time only.Terminal 75A separate ‘terminal 75’ relay is no longer installed in the A3. Other control modules receive the current status of terminal 75 from Electronic Steering Column Lock Control Module J764 via the Convenience CAN bus.NO contact and terminal 15After pressing Access/Start Authorization Button E408, a check is made of the key. If the check is successful, Steering Column Electronic Control Module J764 activates the NO contact and the ignition switches on. To switch on the ignition, voltage is applied to the following three signal lines: • Terminal 15 request 1 • Terminal 15 request 2 • NO contactVehicle Electrical System Control Module J519The three signal wires are monitored by J519. If voltage is present in at least two of the three, Terminal 15 Start Relay J329 is activated and the ignition switches on. It is still possible to start the engine in the event of and open circuit in one of the three signal wires.28Interior lightingTwo interior lighting scenarios are possible for the 2015 A3 depending on model and option choices.1. Basic interior lights (QQ5), standard on Premium and Premium Plus models.and2. Interior light package (QQ4), available with the Convenience package of the A3 Premium Plus and standard equipment on the A3 Prestige model.Standard interior light trim (QQ5)In the basic trim, the lights in the vehicle interior use bulb technology. The lights are located in the overhead module, luggage compartment and glove compartment. The lights are powered by a switched terminal 30. There are no door warning lights. Red reflectors are installed in their place.Vanity lightsTerminal 30gVehicle Electrical System Control Module J519Door contact signalTerminal 30gDoor contact signalConvenience CAN buswith bulbsGround611_024Key:1 2 3 4 5 Vanity lights, left or right Light in glove compartment Luggage compartment light Interior lights in overhead module Rear lights29Interior light package QQ4Interior light package QQ4 is available on the Premium A3 model when the optional Convenience package is installed. It is standard equipment on the A3 Prestige model. When this light package is installed on a vehicle with MMI Navigation plus or MMI Navigation plus with Audi connect, the interior lights can regulated via the MMI under the Car menu. When interior light package QQ4 is ordered, an LED module is installed in the front and rear light housings. The LED overhead module has two reading lights and a central background light. In addition, the vehicle is equipped with four LED footwell lights and a cupholder light. The vanity lights also use LED technology. Active door warning lights using conventional bulbs and door entry lights using LED are installed in the doors. The inner door handle on the driver’s door is also illuminated. The speaker lighting is only available when MMI Navigation plus or MMI Navigation plus with Audi connect is ordered.Terminal 30g Door contact signalVehicle Electrical System Control Module J519Terminal 30gLED overhead moduleRear lightsConvenience CAN busDriver Side Rear Door Control Module J926Driver Door Control Module J386Passenger Door Control Module J387Passenger Side Rear Door Control Module J927611_025with LED technologyKey:1 2 3 4a 4b 5 6 Vanity lights, left or right Light in glove compartment Luggage compartment light Reading lights in LED overhead module Rear lights Background light in LED overhead module Cupholder light 7 8 10 11 12 13 Front footwell lights Rear footwell lights Active door warning light Door entry light Inner door handle light Sound loudspeaker lightingwith bulbsOn vehicles equipped with bi-xenon headlights, the Cupholder light is activated via pin B2 of J519.30Setting options in the Car menuA customer can adjust the brightness of the background lights via the MMI Car menu. It is located under Vehicle settings, Background lighting. There are three adjustable zones: • • • Front zone Footwell zone Door zoneThe actual zones displayed in the MMI menu depends on what optional equipment has been ordered. The following optional equipment displays the following zones in the MMI menu:1. Interior light package 2. Premium Sound If at least two zones are available as options in the MMI menu, the setting option "All zones" is offered and allows all zones to have the same setting.ð ð "Front" & "footwell" zones "Door" zone611_027aOnly the background lights react to brightness adjustments made via the Car menu. The following lights are integrated in the background lighting: • Footwell lights • Cupholder light • Speaker lights31Power supply to interior and background lightsTerminal 58 The task of terminal 58 is to control the instrument lighting, display lighting and the locating lights in the buttons and switches. The lighting effect is dependent on the current brightness level of the vehicle and the customer setting. The brightness of the vehicle interior is measured by a photosensor in the Instrument Cluster. The photosensor signal is sent to Vehicle Electrical System Control Module J519 via the Convenience CAN bus. The customer can set the desired basic brightness of the interior lighting using the retractable control button on the light switch. The setting is by the LIN bus to J519. The duty cycle of the pulse width modulated (PWM) signals of terminals 58xs, 58xt and 58xd are calculated from both input variables.Light Switch E1Instrument Cluster Control Module J285PhotosensorPotentiometerResistance PotentiometerBrightness PhotosensorTerminals 58xs, 58xt and 58xdVehicle Electrical System Control Module J519PotentiometerPhotosensor brightnessTerminal 58xsLocating light Switch Lighting Hazard warning light switchTerminal 58xtTerminal 58xsTerminal 58xtTerminal 58xd611_028A distinction is made between three different versions of terminal 58:Terminal 58xs (formerly terminal 58s): Terminal 58xt (formerly terminal 58t): Terminal 58xd (formerly terminal 58d): Switch locating light Switch locating light with when door opened/when key removed from ignition Display and instrument lighting32Terminals 58xs and 58xd are active as long as the side lights or low beam headlights are switched on. Terminal 58xt corresponds to terminal 58xs with additional advance and trail function. It is pre-activated if, for example, one of the following events occurs: • Vehicle is unlocked • A vehicle door is opened • The ignition is switched on Terminal 58xt is deactivated if, for example, the following event occurs: • The ignition is switched off.Vehicle Electrical System Control Module 1 J519 transfers the values calculated for terminals 58xs, 58xt, and 58xd to other control modules via the CAN bus. The control modules to which lights or displays are connected generate a corresponding PWM signal from the values to control the brightness.The light intensity is based on the duty cycle of the PWM signal.Switched terminal 30 (terminal 30g) The signal for switched terminal 30 is generated by Vehicle Electrical System Control Module 1 J519. This is used only to power lights in the vehicle interior. The following events lead to the activation of terminal 30g: • Switching on the ignition • Manual activation of lights powered via terminal 30g • Unlocking a vehicle door or the rear trunk lid • The vehicle is locked: • Opening a vehicle door or the rear trunk lid• no vehicle door is openThe following events lead to the deactivation of terminal 30g: • The after-run time of terminal 30g has expired (timer starts when ignition is switched off)• Removing the ignition key • Turning the rotary light switchand • the rear trunk lid is closed and • the interior light is dimmedThe following lights are powered by a switched terminal 30 from J519: • Light in glove compartment • Luggage compartment light • Footwell lights • Vanity lights in the sun visors • Interior light bulb in overhead module • Reading lights33Driver assistance systemsRearview Camera R189A back-up camera is optional for the A3 model line up for the first time.611_030Installation location of Rearview Camera System Control Module J772 The back-up camera is located in the rear trunk lid handle where it monitors the area behind the vehicle. A semi-conductor chip in the camera is used to capture the images. The image capture sensor uses CMOS technology and captures color images with a horizontal resolution of 64 pixels and vertical resolution of 492 pixels. The camera lens has a dirt repellent coating. The driver can tell if the lens is dirty by the deterioration of the image quality in the display. It is the responsibility of the driver to ensure the lens is cleaned when dirty.611_02934System implementationTerminal 30Terminal 30High lineLow lineInformation Electronics Control Module 1 J794Infotainment CAN busRearview Camera System Control Module J772Power supply CameraRearview Camera R189Camera groundShielding Video lineShielding Video line611_031Rearview Camera R189 is powered by Rearview Camera System Control Module J772. The camera image is transferred from R189 to J772 by a shielded wire. The incoming raw image is distorted due to the shape and position of the camera lens. It is corrected by control module J772. J772 also adds guide lines and areas to the camera image.The corrected image is then transferred to Information Electronics Control Module 1 J794 by video line. To transfer control commands and required vehicle information, both J772 and J794 are connected to the Convenience CAN. In order to maintain a high quality image display for the customer it is necessary after certain repairs to calibrate the system.Reference For further information on the back-up camera, refer to eSelf Study Program 996603 The Audi Q7 - Driver’s Assistance Systems.".35Audi parking systemThe Audi parking system for the 2015 A3 consists of front and rear acoustic sensors. The feature (7X2) is optional on the A3 Premium plus with the Driver assistance package and standard equipment on the A3 Prestige.611_032System implementationTerminal 15Convenience CAN HighConvenience CAN LowParking Aid Control Module J446611_033aKey: E266 G203 G204 G205 G206 G252 G253 Parking aid button Left Rear Parking Aid Sensor Left Rear Center Parking Aid Sensor Right Rear Center Parking Aid Sensor Right Rear Parking Aid Sensor Right Front Parking Aid Sensor Right Front Center Parking Aid Sensor G254 G255 H15 H22 J791 Left Front Center Parking Aid Sensor Left Front Parking Aid Sensor Rear Parking Aid Warning Buzzer Front Parking Aid Warning Buzzer Parallel Parking Assistance Control Module J79136Audi side assistLane Change Assistance Control Module J769Lane Change Assistance Control Module 2 J770611_036The purpose of the Audi side assist is to monitor the areas behind and to the sides of the vehicle using radar sensors. There is a dedicated radar sensor on each side of the vehicle.If Audi side assist detects a critical situation which could result in an accident if the driver were to change lanes, the system warns the driver by intensive flashing of warning lights in the outside door mirror. The warning light in the mirror of the side where the hazard has been detected flashes.Reference For more information about Audi side assist, please see eSelf-Study Program 996603, Audi Q7 - Driver’s Assistance Systems.37System operationLane Change Assistance Control Module J769 is the master control module for the system function. It participates on the Extended CAN bus. J769 monitors the right side of the vehicle. Lane Change Assistance Control Module 2 J770 is a slave module and communicates with J769 via a private CAN bus. J770 is responsible for activating both Audi side assist warning lamps in the door mirrors.Terminal 15Lane Change Assistance Control Module J769CAN Private High CAN Private LowLane Change Assistance Control Module 2 J770Lane Change Assistance Warning Lamp in Driver Exterior Rearview Mirror K233Lane Change Assistance Warning Lamp in Front Passenger Exterior Rearview Mirror K234 High line Low lineExtended CAN bus611_038Audi side assist is activated and de-activated through the MMI. There is no separate switch.System preferences are saved to the driver’s key.611_039a38Driver Assistance Systems Front Camera R242R242 has been upgraded. It now has an additional red light detector. The camera has a resolution of 1024 x 512 pixels and an aperture angle of 46 degrees. It is supplied by Bosch. The camera also has a new internal image processing control unit that eliminates the need for an additional processing module.611_040In the North American region, Driver Assistance Systems Front Camera R242 is used for the following systems:• Audi active lane assist • Adaptive cruise control (ACC)!39Note After making certain repairs to the vehicle or replacing Driver Assistance Systems Front Camera R242, it must be calibrated using VAS6430. Please refer to the current repair literature for complete details.Influence of R242 on the ACC functionDriver Assistance Systems Front Camera R242 allows the Adaptive cruise control system to respond predictively to traffic situations. This improvement is achieved by monitoring the positions of vehicles driving ahead. By continuously monitoring the traffic, the system can tell when a vehicle driving ahead in the same lane is about to change lanes. The system can tell whether a vehicle driving ahead is about to change from an adjacent lane to its own lane. This information is factored into the ACC control algorithm, resulting in smoother and more predictive control response.R242 electrical connectionsA new CAN bus called CAN sensor is used for exchanging data between R242 and Distance Regulation Control Module J428. Control units R242 and J428 are also extended CAN bus users. Directional Stabilization Assistance Windshield Defogger Z67 is also connected to R242. It is used to remove condensation and ice from the camera lens when needed.Terminal 15Terminal 15Extended CAN bus HighAudi lane assist windscreen heater Z67Extended CAN bus LowDriver Assistance Systems Front Camera R242CAN Sensor HighDistance Regulation Control Module J428CAN Sensor Low611_04140Audi lane assist and active lane assistOverviewAudi lane assist was first introduced in 2007. Lane departure systems warn the driver if their vehicle approaches a detected lane boundary marker (lane marker) and is likely to leave its lane. Lane markers are detected using a windshield mounted camera. In the first generation Audi lane departure system, which is still used on some Audi models, the driver is warned through steering wheel vibration. However, if a turn signal indicator is set before crossing the lane marker, the warning is suppressed. The system assumes the lane change is deliberate. The system is designed for driving on larger highways or expressways at speeds greater than 40.3 mph (65 km/h). In some situations, Audi lane assist may not detect lane markers or activate warnings. In poor ambient conditions, dirty or snow covered roads can prevent the system from issuing warnings. Ambiguous lane markings that might be expected in areas of road construction may also prevent the system from issuing warnings.483_022Further developmentA next generation Audi lane assist system debuted on the 2011 A8. Functionality was enhanced so that lane departure warnings are issued even if only one lane marker is detected. Turning into a corner sharply no longer led to a warning, even if a lane marker was touched or briefly crossed. In addition, a higher resolution camera capable of distinguishing between yellow and white lane markers is now part of the Audi lane assist system.461_00241Active lane assistAudi active lane assist is made possible through the development of electro-mechanical steering. Active lane assist becomes active at a speed of 40mph (65 km/h). It detects lane markings on the roadway based on images from a small video camera mounted on the rear-view mirror. If a vehicle approaches a lane marking without activating the turn signal, the system assists the driver in steering back into the lane by making a slight intervention through the electromechanical power steering system.612_017Active lane assist features of the A3 SedanThe Audi active lane assist system in the 2015 Audi A3 sedan has the following features: • Steering intervention through the electromechanical power steering system motor Steering wheel vibrations can be enabled/disabled through the MMI A system mode that uses continuous steering intervention to assist the driver in keeping the vehicle in the center of their lane A system mode that assists the driver in preventing inadvertent lane departures when approaching a lane marker Warning vibrations are generated by the electromechanical power steering system motor The master control function of the system is through Driver Assistance Systems Front Camera R242• • • • • Audi lane assist and Audi active lane assist are driver assistance systems. They support the driver in preventing inadvertent lane departures but ultimately, it is the driver’s responsibility for remaining in their lane.42Audi steering interventionSteering intervention on the Audi A3 sedan is based on a control module response referred to as “corrective steering input late.” With this steering mode, corrective inputs are not made until the vehicle has already moved close to a lane marker. This is the only mode available on A3 sedan models sold in the North American region. Corrective steering input "late"Steering torque requirement611_043Additional functions483_031Audi active lane assist requires the driver to keep their hands on the steering wheel at all times. Recognition of hands-free driving is made based on signals from Steering Torque Sensor G269. If hands-free driving is recognized, the lane assist function is deactivated temporarily, and the function lamp in the DIS changes color from green to yellow. Once the driver grips the wheel again, the system is reactivated.43OperationActive lane assist is switched on and off using the button on the end of the turn signal stalk.611_043aWhen the system is switched on and is active, the green highway symbol will appear in the instrument cluster.611_043bThe vibration warning can be switched on or off via the MMI.611_043c44Self Study ProgramsFor further information about the technology in the Audi A3 ’13, refer to the following eSelf Study Programs.SSP 970203 The 2011 Audi A8 Driver Assistance SystemsSSP 990603 The 2012 Audi A7 Occupant Protection, Infotainment, Climate Control, and Head-Up DisplaySSP 990503 The 2012 Audi A7 Convenience Electronics and Audi Active Lane AssisteSelf Study Program 990143eSelf Study Program 960143The 2015 Audi A3 IntroductionThe 2015 Audi A3 Running Gear and Suspension SystemSSP 990143 The Audi 2015 A3 IntroductionSSP 970243 The 2015 Audi A3 Onboard Power Supply and Networking SystemsSSP 960143 The 2015 Audi A3 Running Gear and Suspension System45Knowledge AssessmentAn On-Line Knowledge Assessment (exam) is Available for this eSelf-Study Program. The Knowledge Assessment is required for Certification. You can find this Knowledge Assessment at: www.accessaudi.com From the accessaudi.com Homepage:• • • Click on the “ACADEMY” tab Click on the “Academy site” link Click on the Course Catalog Search and select “970343 - The 2015 Audi A3 Vehicle Electronics and Driver Assistance Systems”Please submit any questions or inquiries via the Academy CRC Online Support Form which is located under the “Support” tab or the “Contact Us” tab of the Academy CRC.Thank you for reading this eSelf-Study Program and taking the assessment.46All rights reserved. Technical specifications are subject to change without notice. Audi of America, LLC 2200 Ferdinand Porsche Drive Herndon, VA 2017147970343