TECHNICAL DOCUMENTATION

SSP 990363 – The 2017 Audi R8 Introduction

PDFEN82 pages6 MB
SSP 990363 – The 2017 Audi R8 Introduction - PDF cover

This PDF is currently unavailable.

Read document text
eSelf Study Program 990363The 2017 Audi R8 Introductioni Audi of America, LLC Service Training Created in the U.S.A. Created 1/2016 Course Number 990363 ©2016 Audi of America, LLC All rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC. Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.This eSSP contains video links which you can use to access interactive media.Revision 1:1/2016ii Introduction ....................................................................................... 1Model history ..............................................................................................................................................................2 Overview ......................................................................................................................................................................4Body.................................................................................................... 8Introduction ................................................................................................................................................................8 Production of the R8 body ...................................................................................................................................... 10 Audi lightweight design technology ...................................................................................................................... 12 Seating systems ....................................................................................................................................................... 18Occupant protection.......................................................................... 20Overview ................................................................................................................................................................... 20 System overview ...................................................................................................................................................... 22Engines.............................................................................................. 24Specifications ........................................................................................................................................................... 24 Modifications to the 5.2l V10 engines ................................................................................................................... 26Power transmission........................................................................... 42Overview ................................................................................................................................................................... 42 Selector mechanism ................................................................................................................................................ 44 Transmission functions ........................................................................................................................................... 46 Audi drive select – transmission setups ................................................................................................................ 48 Emergency-releasing the parking lock .................................................................................................................. 50 Transmission overview ........................................................................................................................................... 52 Front final drive 0D4 ................................................................................................................................................ 56 Audi drive select – all-wheel drive configurations ................................................................................................ 63Chassis............................................................................................... 64Overall concept ........................................................................................................................................................ 64 Axles and wheel alignment ..................................................................................................................................... 65 Brake system ............................................................................................................................................................ 69 Steering system ....................................................................................................................................................... 72 Wheels and tires ...................................................................................................................................................... 74Knowledge assessment..................................................................... 76This eSelf Study Program teaches a basic knowledge of the design and functions of new models, new automotive components or technologies. It is not a Repair Manual! All values given are intended as a guideline only. For maintenance and repair work, always refer to the current technical literature.NoteReferenceiii iv IntroductionIn its second generation, the high-performance sports car has been newly developed from the ground up.The mid-engine principle used for the Audi R8 is not only a classic concept in motorsport but also an important piece of Audi tradition. The powerful engines were located in front of the rear axle even in the Grand Prix race cars brought to the start line by Auto Union in the 1930s – a revolutionary step at the time. With the new Audi R8, our engineers are bringing accumulated racing expertise from the race track onto the road. The multi-material Audi Space Frame is the key factor behind the consistent lightweight design of the new Audi R8. It is extremely light and rigid, while being acoustically comfortable and offering a high level of safety. The body shell features a completely new multi-material lightweight construction concept. Carbon fiber reinforced polymer (CFRP) forms the ‘B’ pillars, the center tunnel and the rear bulkhead. The front end, roof arch and vehicle rear are formed by a framework of cast aluminum nodes and aluminum profiles. A cockpit positioned very far forward, a long, flowing back and a relatively short wheelbase – the exterior design makes the technical concept of the mid-engine, high-performance Audi R8 clear upon first sight. The car’s proportions convey more of a race car character, with design ideas from the previous model now more pronounced.Link to “2017 Audi R8 V10 Plus - Jay Leno’s Garage.”641_002Learning objectives for this eSelf-Study Program: Once you have completed this eSelf-Study Program, you will be able to answer questions on the following topics: ›› New features of the multi-material body structure. ›› New features of the occupant protection system. ›› Modifications to the 5.2l V10 FSI engine. ›› New power transmission features. ›› New chassis features. ›› Modifications to the electronics and to the driver assistance systems. ›› New features of the electrical and networking systems. ›› New remote control features. ›› Modifications to and new features of the infotainment system.1 Model historyIn the year 2000 Audi won the Le Mans 24 hours endurance race for the first time with its LMP prototype R8. From then until 2005, the model which gave its name to today's production high-performace sports car secured five overall victories on the Circuit de la Sarthe. The fact that Audi chose the name R8 for its road-going supercar reflects the technological relationship between the two winners. 641_025Le Mans quattro study The concept of a mid-engined sports car bearing the name Audi Le Mans quattro was unveiled at the Frankfurt Motor Show (IAA) in 2003.First generation The Audi R8 was launched on the market in April 2007 and initially available as a coupe powered by the 4.2l V8 FSI engine. From 2006 until the late 2014, a total of 26,037 Audi R8s were produced, including 6176 Spyders.641_026641_027Second generation The second generation of the Audi R8 continues the Audi tradition in mid-engine sports cars. The Audi R8  shares the same platform as the Lamborghini Huracán produced in 2014.641_0282 Production at a new siteThe new Audi R8 is being built in a specially constructed production facility known as the “Audi Böllinger Höfe” in Heilbronn not far from the Audi Neckarsulm plant. It is operated by quattro GmbH. Body manufacturing and final assembly both feature many new methods and are organized for flexibility – especially for a limited volume series with a handcrafted character. This offers the freedom to fulfill any individual customer requests. As many as 500 highly qualified specialists are employed in the new R8 manufacturing facility. They build each car with handcrafted precision in 15 cycles, each lasting approximately 30 minutes. Before delivery, each new high-performance sports car must successfully complete a stringent quality acceptance process.641_029641_030641_0053 OverviewNo other model from the brand with the four rings has a closer affinity to motorsport. None is more striking and more dynamic than the second generation of the highperformance R8. It is characterized by a high-revving mid-engine as well as an extremely dynamic chassis with quattro drive system and fully variable torque control. The R8 has been newly developed from the ground up. It is more taut, more striking and more fascinating both on the race track and on the road.BodyThe Audi Space Frame (ASF) body features a new multi-material lightweight construction concept. Components made from carbon fiber reinforced polymer (CFRP) form the ‘B’ pillars, the center tunnel and the rear bulkhead. The front end, the roof arch and the rear are assembled from cast aluminum nodes and aluminum profiles which, in some cases, employ new alloys. Some components, such as the front splitter, the diffuser or the side blades are optionally available in clear-coated carbon fiber.EnginesTwo versions of the 5.2l V10 engine are available. Both feature the cylinder-on-demand system.ChassisDouble wishbones made from aluminum guide all four wheels. With the Audi drive select dynamic handling system, the driver has the choice of four modes (comfort, auto, dynamic and individual) to control the way in which important technical components operate. As standard, the system incorporates the engine characteristics, steering, S tronic transmission and quattro drive system as well as optional extras such as Audi magnetic ride, the exhaust flaps and dynamic steering.Power transmissionThe R8 uses the 7-speed dual clutch 0BZ transmission that features shift-bywire technology. A launch control system allows full throttle acceleration from a standing start. Transmission characteristics can be personalized by the driver through Audi drive select. Power to the rear axle is through a mechanical limited-slip differential while power to the front is via a newly developed electro-hydraulic all-wheel-drive clutch.4 Displays and operationFully digital Audi virtual cockpit instrument cluster with dynamic animations and graphics. The start-stop and Audi drive select buttons are located on the multi-function steering wheel. The steering wheel in the Audi R8 V10 plus has two additional buttons – one is for performance mode together with a rotary wheel for selecting the drive programs as well as a button for controlling the sports exhaust system. MMI navigation plus is installed as standard; the MMI touch wheel is the central controlling element.HeadlightsFull LED headlights with the High beam assistant are standard equipment.641_003Climate controlThe three central operating elements of the climate control system appear to float weightlessly, underscoring the lightness of the instrument panel. The three-dimensional design of the air outlet vents brings to mind the air inlets of a race car.Assistance systemsThe following systems are standard equipment: ›› Audi drive select ›› Electro-mechanical steering ›› Parking system plus5 Dimensions64.4 in (1638 mm) 76.4 in (1940 mm)641_03248.8 in (1240 mm)62.9 in (1599 mm) 80.2 in (2037 mm)641_03339.1 in (994 mm)104.3 in (2650 mm) 174.3 in (4426 mm)38.5in (977 m m)30.8 in (782 mm)641_0346 59.1 in (1502 mm)2)55.1 in (1400 mm)3)641_035Exterior dimensions and weightsLength Width (not including exterior mirrors) Width (including exterior mirrors) Height Front track width Rear track width Wheelbase Curb weight 174.3 in (4426 mm) 76.4 in (1940 mm) 80.2 in (2037 mm) 48.8 in (1240 mm) 64.5 in (1638 mm) 62.9 in (1599 mm) 104.3 in (2650 mm) R8 V10 3516.3 lb (1595 kg) R8 V10 plus 3428.1 lb (1555 kg) Gross vehicle weight 4111.6 lb (1865 kg)Inner dimensions and other specificationsFront cabin width Front shoulder width Luggage capacity Drag coefficient cw 55.1 in (1400 mm)3) 59.1 in (1502 mm)2) 3.9 cu ft (112 l) / plus 7.9 cu ft (225 l)4)R8 V10 with adaptive rear spoiler retracted: 0.34 R8 V10 with adaptive rear spoiler extended: 0.35 R8 V10 plus with fixed rear wing spoiler: 0.36Capacity of fuel tank19.3 gal (73 l)Maximum headroom Elbow room width 3) Shoulder room width 4) Additional luggage space behind driver and front passenger seats1) 2)All dimensions given refer to the unladen weight of the vehicle.7 BodyIntroductionThe 2017 Audi R8 is based on the Modular Sportscar System (MSS). The MSS provides the body with high stability combined with low weight and represents and entirely new multi-material lightweight design concept. This iteration of the Audi Space Frame (ASF) is very light and stiff. It offers occupants a high level of acoustic comfort and safety. The front end, roof frame and rear have a lattice design consisting of aluminum castings and extruded aluminum profiles. They are tailored specifically for their place and purpose. In the event of a collision, the forces exerted on the side member structures are directed downwards and dissipated. For energy dissipation purposes, the side members should deform in a controlled manner and optimally transmit the residual energy to the next component. When repairing this body, it is important to keep these defined deformation zones intact and to not disrupt the transfer of forces. To help ensure that this is the case after repair work, the depth of allowable repair and repair methods are defined in detail in the current repair literature.BodyThe body consists of the inner structure and the roof outer skin. The structure is assembled from welded extruded aluminum profiles and aluminum castings.Key:Sheet aluminum Die-cast aluminum Aluminum profile Carbon fiber reinforced polymer (CFRP)Front endThe front end is made from extruded aluminum profiles and has aluminum castings for force absorption at the points where force is transferred to the vehicle interior.8 Carbon fiber reinforced polymer (CFRP)Carbon fiber reinforced polymer (CFRP) is a modern and attractive composite material which fits in very well with the Audi lightweight design strategy. The material-specific advantages of CFRP are significant, particularly its weight to rigidity and strength ratios. The first generation of the R8 incorporated many large and small non-structural CFRP components that were attached to the aluminum structure, such as the side walls and the convertible top box lid of the R8 Spyder. With the 2017 R8, Audi is using CFRP components made using the efficient RTM (Resin Transfer Molding) process for the first time. In this process, the dry fiber rovings (twisted strands) are first shaped and then inserted into heated molds where an epoxy resin is injected under high pressure after closing the press. The fabric is completely saturated and hardened under pressure and controlled temperature. Carbon fiber reinforced polymer is not only about 20% lighter than aluminum and 60% lighter than steel – but also gives designers the freedom to custom-design components to meet a variety of requirements.Rear structureExtruded aluminum profiles and aluminum castings form the rear. The suspension mounts are integrated in the castings.Center floor panThe center floor pan is composed of the tunnel side members, the seat cross members and the floor panels. It is subsequently enclosed by the CFRP tunnel.641_1109 Production of the R8 bodyDue to the different temperature characteristics of aluminum and CFRP, the R8 body is manufactured in two stages.Stage 1 Bodyshop 1 and the paint shop carry out the preliminary work on the bodyshell.First, the ASF structure is completed. The front end, center floorpan, rear and body are assembled and prepared for painting as a complete body with attachments. After this, the bodyshell passes through a dip bath in the paint shop. This process is referred to as "cataphoretic dip coating" (CDC) and protects the body against corrosion. Before the body can be painted the CFRP adhesive surfaces must be masked. The coated and masked body is now painted and dried and hardened at a temperature of over 392 °F (200 °C). Because the CFRP components are only able to withstand temperatures of up to about 248 °F (120 °C) due to the epoxy resin, they are assembled subsequently. Another reason for taking this approach is that aluminum and CFRP have different coefficients of thermal expansion.Stage 2 In Bodyshop 2 the bodyshell is completed together with the CFRP components.Stage 1 is followed by manual removal of the painted attachments and demasking of the surfaces. Accessibility for subsequent process steps is improved by removing the attachments (doors, rear hatch and body side sections). After cleaning the adhesive surfaces, the CFRP components are installed on the painted body and integrated into the structure using bonding, bolting and riveting methods. A further process step after joining and placement of the rivet elements is the sealing of the CFRP structural components. Edges, rivets and rivet nuts are sealed with polyurethane (PU) to prevent the ingress of liquid and moisture into the joined components. After this, the body is stored for 6 hours at room temperature before being hardened in an oven at 176 °F (80 °C) for about 45 minutes.Joining techniquesSemi-tubular punch rivetBonding + pop riveting Metric boltingBonding + metric boltingFlow drill screws Bonding + flow drill screws TIG welding641_11110 CFRP components 1 Rear bulkhead The complex rear bulkhead is assembled from 17 CFRP components, two aluminum castings and two extruded aluminum profiles. It is bonded, riveted and bolted into the R8 aluminum structure as a complete unit. 2 Upper ‘B’ pillar The CFRP upper ‘B’ pillars are bonded and riveted to the rear bulkhead providing additional support.4 1 2641_113641_112 3 Tunnel In the next stage of the process the three piece CFRP tunnel is integrated into the body structure from below. Bonding bolting and flow drill screwing are used as joining methods.641_114 4 Outer ‘B’ pillar43641_115The outer ‘B’ pillar is assembled last and is integrated into the body structure using bonding, riveting and bolting methods. It incorporates the striker reinforcement, the sill support mounts and the mounts for the body side section and side blade.641_116Stage 1 Bodyshop 1 CDC/paintStage 2 Bodyshop 211 Audi lightweight design technologyAt Audi, lightweight design technology applies the maxim “the right material in the right quantity in the right place.” To achieve this, CFRPs are used as structural components of the 2017 R8 to reduce vehicle mass. Force = mass x acceleration. Reducing the mass of the vehicle has several advantages. Less force, and therefore less fuel is required to achieve the same acceleration. Conversely, the same force produces higher acceleration.Carbon fiber reinforced polymer (CFRP)CFRP is a composite material. It is a combination of two or more components: a reinforcing fiber and a matrix which bonds the fibers together. The combination forms a component of very high strength and rigidity. The task of the fiber is to transfer load and absorb elongation. They also define the rigidity, strength and thermal expansion of the fiber composite. Fibers are, in principle, only able to absorb tensile forces but not compressive forces. If the fiber composite needs to be rigid in more than one direction, it is usually woven or layered at different angles.Reinforcing fibersMatrix641_089Fabric641_090Fiber roving641_091Resin is the matrix of the CFRP composite. The matrix bonds and protects the fibers and prevents them from buckling.The rigidity, strength and thermal expansion of the fiber composite are, likewise, partly defined by the matrix.Advantages of CFRPThe main advantage of CFRP is the saving of weight. CFRP also offers advantages such as low thermal expansion, high corrosion resistance, good aging properties / fatigue strength, design freedom and good absorption properties (crash behavior). The following comparison shows how much component weight can be saved while retaining full functionality by using different materials.100 %-40 % 75 %-55 %-60 %-75 %1)50 % FRP quasi-isotropic – the properC ties of the material are virtually the same in all directions.  FRP unidirectional – in this conC nection, the fibers are oriented in one direction only.MagnesiumAluminumquasi-isotropic1)2)25 %unidirec-SteelCFRPCFRPtional2)641_09212 Resin Transfer Molding – RTMThe CFRP parts for the Audi R8 are manufactured at Audi using the Resin Transfer Molding method. The basic steps of this RTM process are described below.641_093641_094641_095A parting agent is applied to both sides of the mold to make removing the finished component easier.Multiple tailored layers of the textile structures are stacked on top of each other inside the mold.The mold is then closed.641_098641_097641_096After setting, the mold is opened and the component removed.The resin sets within 5 to 10 min at a temperature of between 176 -248 °F (80 - 120 °C)Epoxy resin and hardener are injected into the component for between 10 to 60 seconds. The fibers are completely saturated with the liquid resin.Carbon fiber reinforced polymer at AudiDepending on application, a distinction is made between visible CFRPs, Class-A CFRPs and structural CFRPs. Visible CFRPs are used, for example, in the making of interior trim panels or door mirrors. The surface of the CFRP part is protected by a clear coat. Until now, Class-A CFRPs have mainly been used for exterior attachments, such as body side sections and the convertible top box lid on the R8 Spyder.641_101641_099641_10013 Structural CFRPsStructural CFRPs do not have a visual function in the automobile but are relevant to safety. Structural CFRP components are integrated in the vehicle body and replace a part of the bodyshell which would otherwise be made from aluminum or steel. The structural CFC must, therefore, be capable of withstanding and absorbing high loads during vehicle operation or in an accident situation. Structural CFRPs have to meet exacting quality requirements. The center tunnel, the upper and outer ‘B’ pillars and the rear bulkhead of the R8 are all manufactured from structural CFRPs.641_102Non Destructive Inspection (NDI)After an accident, it may not be possible to visually detect potential damage within the CFRP structure. CFRP components can be dramatically impaired by minor damage. Delamination (layer separation) can occur due to an impact which will impair strength, rigidity, flexural stability and dent resistance of the laminate. Components can be non-destructively inspected using an ultrasound testing device. Ultrasonic pulses which have a very short duration (1 - 10 microseconds) are directed through the component being tested. These sound waves are reflected by the wall of the component under inspection and return to the testing device. Special software computes the depth at which the sound was reflected (rear wall or defect) on the basis of the time elapsed between transmission and reception of the signal. This information is then displayed on a monitor using different colors.ProbeComponent thickness641_103 641_104CFRP componentDefect in component14 EvaluationThe color coding in the evaluation shows the defect or damage to the component. If no defect is detected, a monochrome image will be displayed.The positions in which a defect is found are indicated in color.Defect-free region641_105Region with defective CFRP641_106Reference For further information about the non destructive inspection of CFRP components, refer to the current service literature in ElsaPro and ServiceNet.Important service information›› Do not drill, saw, sand and perform other machining operations on CFRP components. ›› CFRPs are electrically conductive. However, it is not permissible to make electrical connections to ground through CFRPs. ›› Avoid all contact with CFRP components while carrying out work on electrical wiring (danger of short circuit). ›› Avoid hard contact with CFRP parts when repairing vehicles, for example, when removing or installing units (danger of non-visible irreparable damage to the CFRP structure). ›› Only manufacturer-approved materials, for example, primers, adhesives, rivets, may be used when performing work on the body. ›› Work on the body may only be performed using methods approved by the manufacturer. ›› Work on the body may only be performed using tools approved by the manufacturer.15 AerodynamicsSports cars are built to achieve one thing above all else: driving performance. A key requirement for this is the aerodynamic design – in addition to high engine output low weight, a rigid chassis and a balanced weight distribution. An important factor to consider with regard to aerodynamics is the strong correlation between downforce and drag because the higher the downforce of a vehicle, the higher its drag coefficient that is, it takes more propulsive force to generate the energy needed to produce drive.Audi R8 V10 with extended rear spoiler641_107Compared to other supercars, the Audi R8 V10 has a very low drag coefficient: 0.34 with the rear spoiler retracted, 0.35 with the rear spoiler extended and 0.36 in the R8 V10 plus version with fixed rear spoiler.To improve downforce at higher speeds, the rear spoiler of the R8 V10 automatically extends electrically when the vehicle exceeds a speed of about 75 mph (120 km/h). To produce more downforce, the Audi R8 V10 plus has a fixed wing made of CFRP.Audi R8 V10 plus with fixed rear spoiler641_10816 Drag reduction panelsThe drag reduction panels at the front and rear of the underbody and at the center tunnel ensure that the surface of the underbody is smooth. NACA ducts1) in the underbody trims allow additional air to be channeled around the fuel tank and into the engine bay without causing a significant increase in drag. A long, rising diffusor in the underbody exerts downforce on the rear axle at higher speeds.641_109Drag reduction panel, front underbodyDrag reduction panel, center tunnelDrag reduction panel, rear underbodyNote To achieve highest levels of driving performance and driving safety and to ensure that the suspension components, drive units and brakes are properly cooled, all underbody panels and wheel arch linings, front and rear spoiler elements and air ducts must be installed correctly.1)NACA: National Advisory Committee for Aeronautics (precursor to NASA). An NACA duct is an air intake integrated in the outer skin of a vehicle. 17 Seating systems2 different seat versions are available for the new Audi R8 – the R8 sports seat and the R8 bucket seat. As an option, both versions can be ordered with seat heaters. Depending on seat version, new features for the Audi R8 are an integrated head restraint, electrical seat depth adjustment and pneumatic adjustments.R8 sports seatThe sports seat is only available in one version in the North American Market. ›› Fully electric sports seat with pneumatic bolster adjustment in the backrest and on the seat base.Driver and Passenger Backrest Adjustment Motors V45, V46Manual fore and aft adjustment641_01918 Fully electric sports seat›› ›› ›› ›› ›› ›› ›› ›› Electric length adjustment. Electric height adjustment. Electric backrest angle adjustment. Pneumatic 4-way lumbar support. Pneumatic seat base bolster adjustment. Pneumatic backrest bolster adjustment. Fold-down backrest. "Dynamic diamond" stitching pattern. (Optional)Pneumatic backrest bolster cushionPneumatic seat bolster cushionPneumatic lumbar support641_021R8 bucket seatThe R8 bucket seat is based on a carbon seat shell. It also folds down, but the backrest angle is not adjustable. The R8 bucket seat has manually adjustable fore and aft movement as well as electric height adjustment.Fully electric sports seat, version 2Manual fore and aft adjustment641_022Seat Depth Adjustment Button E35019 Occupant protectionOverviewDriver airbag Front passenger airbagDriver side knee airbagSide airbag, driver sideComponents›› ›› ›› ›› ›› ›› ›› ›› ›› Airbag Control Module. Driver airbag. 2-stage front passenger airbag. Front side airbags. Head airbags. Knee airbags. Front airbag crash sensors. Crash sensors for side impact detection in the doors. Crash sensors for side impact detection in the ‘B’ pillars. ›› Front inertia-reel safety belts with pyrotechnic belt tensioners with adaptive belt force limiters. ›› ›› ›› ›› ›› ›› Safety belt warning for all seats. Safety occupancy sensor in front passenger seat Front passenger airbag disabling switch. Front passenger airbag OFF and ON warning lamp. Driver and front passenger seat position sensors. Battery interrupt igniter.20 Passenger side knee airbagHead airbag, driver and front passenger sidesSide airbag, front passenger side641_16021 System overview641_023 (rev)22 Key to illustration on page 22:E24 E25 Driver Seat Belt Switch Front Passenger Seat Belt Switch K19 Seat Belt Indicator Lamp K75 Airbag Indicator Lamp K145 Front Passenger Airbag -Disabled- Indicator Lamp N95 Driver Airbag Igniter N131 Front Passenger Airbag Igniter 1 N132 Front Passenger Airbag Igniter 2 N153 Driver Seat Belt Tensioner Igniter 1 N154 Front Passenger Seat Belt Tensioner Igniter 1 N199 Driver Thorax Airbag Igniter N200 Front Passenger Thorax Airbag Igniter N251 Driver Head Curtain Airbag Igniter N252 Front Passenger Head Curtain Airbag Igniter N253 Battery Interrupt Igniter N295 Driver Knee Airbag Igniter N296 Front Passenger Knee Airbag Igniter T16 Data Link ConnectorG128 Front Passenger Occupant Detection Sensor G179 Driver Thorax Airbag Crash Sensor G180 Front Passenger Thorax Airbag Crash Sensor G256 Driver Side Rear Thorax Airbag Crash Sensor G257 Passenger Side Rear Thorax Airbag Crash Sensor G283 Driver Front Airbag Crash Sensor G284 Passenger Side Front Airbag Crash Sensor G551 Driver Belt Force Limiter G552 Front Passenger Belt Force Limiter G553 Driver Seat Position Sensor G554 Front Passenger Seat Position Sensor J234 J285 J533 J706 Airbag Control Module Instrument Cluster Control Module Data Bus On Board Diagnostic Interface (Gateway) Passenger Occupant Detection System Control ModuleDiagram color identification: Powertrain CAN Convenience CAN Diagnostics CAN FlexRay Input signal Output signal23 EnginesSpecificationsTorque-power curve of 5.2l V10 engine (engine code CSPA)603 hp (450 kW) 479 lb ft (650 Nm)   Power output in hp (kW)   Torque in lb ft (Nm)536 hp (400 kW) 442 lb ft (600 Nm)469 hp (350 kW)406 lb ft (550 Nm)402 hp (300 kW)369 lb ft (500 Nm)335 hp (250 kW)332 lb ft (450 Nm)268 hp (200 kW)295 lb ft (400 Nm)201 hp (150 kW)641_123258 lb ft (350 Nm)The engine number can be found on the right-hand side of the engine block, below the cylinder head on the poly-V belt side.134 hp (100 kW)221 lb ft (300 Nm)67 hp (50 kW)184 lb ft (250 Nm)Engine speed [rpm]641_006Features Engine code Type Displacement Stroke Bore Number of valves per cylinder Firing order Compression ratio Power output at rpm Torque at rpm Fuel type Engine management system Oxygen sensor/knock control Mixture formation Emission standardSpecifications CSPA 10-cylinder V-engine with 90° V angle and dry sump lubrication 317.6 cu in (5204 cm3) 3.65 in (92.8 mm) 3.33 in (84.5 mm) 4 1-6-5-10-2-7-3-8-4-9 12.5:1 540 hp (397 kW) @ 7800 rpm 398 lb ft (540 Nm) @ 6500 95 RON Bosch MED 17.1.1 dual control modules (master/slave concept) Adaptive O2, adaptive knock control Combined (dual) direct (FSI) and multipoint (MPI) injection LEV II - ULEV / Tier 2 - BIN 524 Torque-power curve of 5.2l V10 plus engine (engine code CSPB)   Power output in hp (kW)   Torque in lb ft (Nm)603 hp (450 kW) 479 lb ft (650 Nm)536 hp (400 kW)442 lb ft (600 Nm)469 hp (350 kW)406 lb ft (550 Nm)402 hp (300 kW)369 lb ft (500 Nm)335 hp (250 kW)332 lb ft (450 Nm)268 hp (200 kW)641_039295 lb ft (400 Nm)The engine number can be found on the right-hand side of the engine block, below the cylinder head on the poly-V belt side.201 hp (150 kW)258 lb ft (350 Nm)134 hp (100 kW)221 lb ft (300 Nm)67 hp (50 kW)84 lb ft (250 Nm)Engine speed [rpm]641_007Features Engine code Type Displacement Stroke Bore Number of valves per cylinder Firing order Compression ratio Power output at rpm Torque at rpm Fuel type Engine management system Oxygen sensor/knock control Mixture formation Emission standardSpecifications CSPB 10-cylinder V-engine with 90° V angle and dry sump lubrication 317.6 cu in (5204 cm3) 3.65 in (92.8 mm) 3.33 in (84.5 mm) 4 1-6-5-10-2-7-3-8-4-9 12.5:1 610 hp (449 kW) @ 8250 413 lb ft (560 Nm) @6500 95 RON Bosch MED 17.1.1 dual control modules (master/slave concept) Adaptive O2, adaptive knock control Combined (dual) direct (FSI) and multipoint (MPI) injection LEV II - ULEV / Tier 2 - BIN 525 Modifications to the 5.2l V10 enginesAir intake system641_012641_124Coolant expansion tank641_008Oil tank with dry sump lubrication26 641_085Dual fuel injection systemCylinder-on-demand641_042641_009Modified cooling circuit641_04027 Oil circuitThe 5.2l V10 engine are, like its predecessor, equipped with a dry sump lubrication system. The very low installation position of the engine brings the center of mass of the vehicle closer to the road. Lubrication of the engine must be maintained at all times regardless of driving style. This is ensured by the oil pump module and external oil reservoir. The crankcase chambers are separated from one another by an oil deflector. The geometry of the blade reduces gas circulation and churning losses within the chambers.OverviewEngine oil cooler Upright oil filter module Engine oil reservoirEngine oil coolerCombined oil and engine coolant pump641_04128 Oil deliveryThe pump provides continuous extraction of engine oil from the crankcase, timing chain case and the cylinder heads through two suction stages.Oil pumpsIt pumps the oil through the two oil-coolant heat exchangers into the oil tank.Coolant intake duct, Left cylinder bankThermostat housingOil pump module is driven by chain drive DCoolant pumpCoolant intake duct, Right cylinder bank641_087Attachment of the oil pump module to the intake modulePressurised oil duct in the engine oil circuitOil tank with dry sump lubrication The blow-by gases are separated from the oil by a cyclone built into the top section of the oil reservoir. The blow-by gas flows out of the oil reservoir and into the intake manifold via the fine oil separator downstream of the throttle flaps. The separated oil collects in the bottom of the oil reservoir. From here, the oil is drawn in on the suction side of the pump pressure stage and flows through the main oil filter to the bearings.Blow-by gases to the coarse oil separatorBlow-by gases to the coarse oil separatorOil filler neckCoarse oil separator (cyclone)Oil reservoirOil Level Thermal Sensor G266641_008Oil extraction by the oil pumpOil return from the oil pump29 Crankcase ventilationPositive crankcase ventilation is provided by the cylinder head covers in which a large settling chamber acts as a gravity oil separator. A 3-stage register cyclone with a bypass valve is used as a fine oil separator.Connection below intake manifold downstream of throttle valve Connection in the inner V for positive crankcase ventilation Connection upstream of throttle valve for ventilation of the crankcase with non-return valve Oil reservoir ventilation and inflow to coarse oil separatorPressure control valve for positive crankcase ventilation641_163Fine oil separator (mini-cyclone separator)Coarse oil separator in the cylinder head coverInflow of blow-by gases from the oil reservoirEvaporative emission systemThe 5.2l V10 engines feature cylinder-on-demand (COD) which requires the use of two Evap Canister Purge Regulator Valves. In COD mode, the active cylinder bank must vent the carbon canister into the intake manifold while the valve for the inactive cylinder bank closes.Evap Canister Purge Regulator Valve 1 N80 Connection 1 to intake manifold for cylinder bank 1Evap Canister Purge Regulator Valve 2 N115Connection 2 to intake manifold for cylinder bank 2Carbon canister connection641_16430 Air supplyThe engine is supplied with air via the side blades. In high load demand situations, active bypass flaps in the air filter boxes are opened. If the active bypass flaps are open, the engine draws in air through the air grid below the rear window (in front of the rear spoiler). While driving, the side-blades direct the airflow through additional outlets into the engine bay in order to prevent heat build-up from occurring here. At the same time, the air flows through both auxiliary radiators for ATF cooling and oil cooling.OverviewRight bypass valveLeft bypass valveRight side-bladeAir ductEngine bay ventilation641_012Left side-bladeNoise reduction To reduce noise from the engine, the bypass valves in the air filter boxes are closed when the engine is started, at idle and at drive-away. The bypass valves open when the mass air flow rate exceeds 140 kg/h and close when it drops below 120 kg/h. To utilize the full power of the engine, the bypass valves must be opened if the characteristic in the engine map is exceeded. The bypass valves are actuated by vacuum motors.31 Dual fuel injection systemFor the first time, the Audi R8 uses a fuel injection system that combines the advantages of the direct and indirect injection systems. In the classic indirect injection system, the air-fuel mixture is formed upstream of the intake valve. This results in better mixture formation, lower particulate matter emissions and less fuel condensation in the cylinder. In the direct injection system, the thin fuel film on the inner walls of the cylinders provides better cooling and a reduced knock tendency. Other advantages are the very short injection time and the high efficiency of the system. Depending on engine load, the ECM selects the appropriate system – from indirect injection only to a situation-based combination of both types of injection. The result is a better power yield, better fuel economy and lower emissions.MPI indirect injectorFSI direct injector641_024Operating characteristics of the combined fuel injection systemKey: *NEDC operating points 15% MPI, 85% FSI 50% MPI, 50% FSI 100% MPITorque [Nm]Engine speed [rpm]32641_011*The New European Driving Cycle (NEDC) represents the typical usage of a car driven in Europe. Fuel supplySystem overview The MPI system has its own pressure sensor - Low Fuel Pressure Sensor G410. Pressure is supplied on demand by Transfer Fuel Pump G6 in the fuel tank. It is activated by Fuel Pump Control Module J538 via the ECM. The high-pressure fuel pumps are driven by a 2-lobe cam on the intake camshafts. Depending on engine speed and requirements (map), they generate system pressures ranging from about 1450 psi (100 bar) at 350 rpm to 2900 psi (200 bar) at about 3000 rpm. Both cylinder banks are supplied with fuel in such a way that they operate separately from one another.Low-pressure rail Low Fuel Pressure Sensor G410 High pressure fuel rail Low-pressure rail Low Fuel Pressure Sensor 2 G896 High pressure fuel rail High-pressure pump 2High-pressure pump 1Fuel Metering Valve N290 Filler neck with cap-less locking systemFuel Pressure Sensor 2 G624Fuel Pressure Sensor G247Fuel Metering Valve 2 N402Bleed lineCarbon canisterTransfer Fuel Pump G6Fuel Pump G23641_088Right fuel tankDirection of travelLeft fuel tank33 Cylinder-on-demandWhen cylinder-on-demand is active, the injection and ignition systems for one cylinder bank are shut down by the ECM. The driver is not informed when cylinder-on-demand is active. Enabling conditions ›› Engine at operating temperature (coolant temperature higher than 113 °F [45 °C]). ›› 3rd gear or higher is selected. ›› Vehicle travelling faster than 16.8 mph (27 km/h). ›› Engine speed between 1000 and 4500 rpm. ›› The mean temperature of the catalytic converter is the control variable for enabling cylinder bank shutoff. The calculated temperature of the converter must be greater than 662 °F (350 °C). ›› Low to medium engine load with maximum cylinder charging at about 65% (depending on engine speed). ›› Maximum torque: approximately 133 - 146 lb ft (180 - 200 Nm).641_04234 Exceptions to cylinder-on-demand operationThere is no possibility of cylinder shutdown at high engine load on roads with a gentle gradient or when coasting on roads with a steep gradient. In periods of a defined steering angle, a defined accelerator position or when the brake is applied, cylinder shut down is suppressed for a short time, for example, in a roundabout.If the accelerator position changes repeatedly or numerous steering inputs are made, for example, in urban traffic the probability of cylinders being shut down is reduced.Algorithm for cylinder bank changeover The modeled catalytic converter mean temperature is the control variable for the running time in cylinder-on-demand mode. If temperature in the catalytic converter drops below the minimum temperature of about 662 °F (350 °C) while a cylinder bank is shut off, both cylinder banks (full engine operation) will be activated for about two seconds. Then, when the temperature of the catalytic converter on the other cylinder bank exceeds 662 °F (350 °C), this bank switches to cylinder-on-demand mode. To avoid cross flow between the cylinder banks (via the blow-by line), the throttle valves of both cylinder banks are set at the same angle. To avoid frequent changeovers, cylinder shutdown is only enabled if the physical enabling conditions have been met and there is enough time for cylinders to shut down. In the Audi R8 V10 (6 plus overdrive transmission), the longer gear ratios lead to a shift in the load points (lower engine speed – higher load). Accordingly, the active range of the cylinder on demand function in the Audi R8 V10 is smaller, and less noticeable. Driving at the same speed, the Audi R8 V10 plus may utilize the active range of the cylinder-on-demand function in the dynamic mode of the Audi drive select handling system while the Audi R8 V10 does not.SENT sensor electronics Throttle valve, Right hand cylinder bank Throttle valve, Left hand cylinder bank641_045Driver profile There is no driver profile adaptation during cylinder shutoff. The vehicle is reset to the initial state after every restart. Regardless of the driver's previous behavior, the vehicle is reset to the same initial state as at start-up after a maximum of 30 seconds of steady driving.Exhaust temperature sensor The V10 and the V10 plus each have a single temperature sensor per cylinder bank configured as a SENT sensor1). The electronics are integrated in the sensor connector. The sensor calculates a theoretical mean temperature for cylinder-on-demand operation. It monitors the catalytic converter and protects it from overheating.Heated Oxygen Sensor G39 (broadband) Exhaust Gas Temperature Sensor 1 G235 (right hand cylinder bank)1) he SENT (Single Edge Nibble Transmission) data protocol can, in conjuncT tion with the appropriate sensors, be used for digital data transfer instead of analog interfaces.Oxygen Sensor After Catalytic Converter G130 (non-linear)641_08635 Cooling circuit1235674910811 G62V5113121415 16 17J671 19 18 19 21J29320641_00436 Key to illustration on page 36 1 2 3 4 5 6 7 8 9 10 11 12 13 Coolant expansion tank Coolant thermostat for ATF cooling Transmission oil cooler (ATF heat exchanger) Auxiliary radiator for ATF cooling (air to water) Cylinder head, bank 1 Positive crankcase ventilation Cylinder head, bank 2 Liquid-cooled alternator Engine oil cooler (water to oil) Left hand auxiliary radiator for engine oil cooling (air to water) Coolant pump Coolant thermostat Engine oil cooler 2 (water to oil) 14 15 16 17 18 19 20 21 G62 J293 J671 V51 Coolant thermostat for engine oil cooler Front axle differential Flow restrictor Heater heat exchanger Right hand auxiliary radiator (air to water) Vent screw Main radiator Left hand auxiliary radiator (air to water) Engine Coolant Temperature Sensor Radiator Fan Control Module J293 Radiator Fan Control Module 2 J671 After-run Coolant PumpCoolant expansion tankThe cooling system is filled with G13 and distilled water and has a capacity of 25.3 qt (24l). The coolant expansion tank has a float-type dipstick which allows the coolant level to be checked more easily. The dipstick must extend about 0.4 in (1 cm) (1st slot) over the edge of the coolant expansion tank when the engine is cold. The expansion tank has a silicate filling, which does not need to be renewed. It consists of a silica gel (SiO2) with a grain size ranging from 0.5 – 2.0 mm. When the coolant expansion tank is replaced, the new tank is pre-filled with silicate.Connection for vent line from front radiator assembly (goes to crankcase breather heater)Connection from auxiliary radiator for engine oil cooling Connection from auxiliary radiator for ATF coolingSealing cap with pressure regulator (the pressure relief valve must open at an excess pressure of 23.2 - 29.0 psi (1.6 - 2.0 bar)Silicate fillingFloat-type dipstickCoolant supply to cooling circuitEngine Coolant Level Sensor G32641_12437 Radiator and coolant linesThe cooling system has three radiators placed at the front end. Two radiators are located behind the large lateral air ducts, which are supplied with cooling air by two large fans. Another radiator is located at the center at the lower edge behind the single-frame grille and is effectively supplied with cooling air by aerodynamically optimized air ducts without the use of a fan. The high performance coolant pump is flange mounted to the engine and pumps coolant to all three radiators through 1.4 in (36 mm) aluminum pipes. The coolant flow is divided by a ‘Y’ connection and directed to the two outer radiators. After passing through the left hand radiator, coolant flows directly to the return line to the coolant pump. In the right-hand radiator, the coolant is re-directed through the radiator and into the main radiator. After flowing through the auxiliary radiator, the coolant flows directly into the return line and back to the engine through a bypass in the auxiliary radiator. The advantage of this combined series and parallel configuration of the left and right-hand sides is that it allows a uniform distribution of the coolant while maximizing the rate of flow through all three radiators. The cooling system does not feature Innovative Thermal Management.OverviewCoolant connection for front axle differential cooler plateVent valvesVent linesRight hand auxiliary radiatorMain radiatorLeft hand auxiliary radiator38 Auxiliary radiator (air to water) for ATF coolingCoolant expansion tank with float-type dipstickAuxiliary radiator for engine oil cooling (air to water), thermostat controlledAfter-Run Coolant Pump V51Plate-type engine oil cooler (water to oil)Coolant thermostat for engine oil coolerEngine oil cooler 2 as plate-type cooler (water to oil)641_036Secondary coolingTo provide for secondary cooling of the engine after it has been subjected to high thermal load, both fans and the separate after-run pump are activated after the engine is shut off. Having been pre-cooled by the fan, the secondary coolant flows to the engine through the coolant lines and ensures that the high temperatures are quickly dissipated at the cylinder heads.39 Exhaust systemThe auditory driving experience is essentially a combination of engine and powertrain noise, roll comfort including tire/ road noise, as well as wind noise. This noise has to be counterbalanced by the sports car sound of the engine, as characterized by the sporty mid-engine concept of the Audi R8. The object is to accompany every movement of the accelerator and every change in engine speed and torque by sound modulation which not only matches the performance and power delivery of the engine but also accentuates the experience. All of these are key to engine sound design. Its sound characteristic is distinguished by a powerful and restrained engine note at part throttle and by a sporty and voluminous soundscape at full throttle. During changes in engine speed and load, this sound is modulated to provide the driver with audible feedback on the performance and power delivery of the V10 engine.SENT sensor electronicsExhaust Gas Temperature Sensor 2 G448Heated Oxygen Sensor 2 G108 Oxygen Sensor 2 After Catalytic Converter G131Main catalytic converter for left hand bank, cylinders 6 - 10Exhaust gas flap with vacuum motor, left hand sideExhaust end piece40 The exhaust system of the Audi R8 uses a reflection-type silencer and consists of: ›› 2 catalytic converters with heated oxygen sensors before the catalytic converter. ›› 2 temperature sensors. ›› 2 post catalytic converter oxygen sensors. ›› 2 main catalytic converters fitted in the main silencer. ›› 2 exhaust flaps.A special feature of the inner tubes in the silencer is that the exhaust gases flow from the right-hand cylinder bank to the tailpipes on the left-hand side and emerge in reverse.SENT sensor electronicsHeated Oxygen Sensor G39Exhaust Gas Temperature Sensor 1 G235Oxygen Sensor After Catalytic Converter G130Main catalytic converter for right hand bank, cylinders 1 - 5Exhaust gas flap with vacuum motor, right hand sideExhaust end pieceRear silencerReflection chambers641_19941 Power transmissionOverviewThe power of the V10 engines of the R8 is transmitted to the wheels by the 7-speed DSG transmission 0BZ, and a new front axle differential. The newly developed front axle differential incorporates an electro-hydraulic multi-plate clutch which allows drive force to be variably distributed to the front axle. When the all-wheel drive clutch is not activated, 100% of the drive force is transmitted to the rear axle. Its mechanical limited slip differential provides traction at the rear wheels. Depending on driving situation, driver input and weather conditions, up to 406 lb ft (550 Nm) of torque can be transmitted through the pinion shaft (refer to page 59) to the front axle final drive within a fraction of a second. This variable distribution of torque to the front axle allows driving dynamics to be controlled in a specific way. This, together with torque vectoring and other driving dynamics systems, creates a highly emotional driving experience.Automatic Transmission Control Module 2 J1006 Transmission Control Module J217 (integral component of the Mechatronic module)7 speed dual clutch transmission 0BZ – S tronic42 The Audi drive select handling system allows the driver to select different setups for the transmission and the allwheel drive clutch. It is possible to experience driving dynamics ranging from comfortable and balanced to particularly sporty.The new performance mode on the V10 plus provides sporty transmission and driving dynamics setups (refer to page 48 and  63).All Wheel Drive Control Module J492Selector mechanism with new control concept and full "shift-by-wire" capabilityFront final drive 0D4 – with all-wheel drive clutch (refer to page 56) Parking lock – emergency release641_046Drive shaft The drive shaft transmits the drive torque from the transmission output shaft to the propeller shaft. It is located inside the engine (it runs through the engine oil pan), and is not visible from the exterior (page 53 and  56).Torque vectoring at both axles.Reference For further information about the front final drive 0D4, refer to eSelf Study Program Self-Study Program 950163, Final drive OD4.43 Selector mechanismThe Audi R8 uses the latest generation Audi selector mechanism of the B and C vehicles with full "shift-by-wire" capability. The parking lock is normally engaged and disengaged using the Auto P function, but can also be engaged by the driver using the P button (refer to page 46). After every operation, the selector lever always returns to the normal position of the automatic or Tiptronic gate M.Basic shift schematic Possible positions of the selector lever: Normal position X in automatic mode or normal position T in Tiptronic mode. Depending on the selector lever position, this position information (A1, A2 etc.) can be displayed in the Measuring values using the VAS Scan Tool.641_047Tiptronic gateShift schematicAutomatic gatePositions selectable without moving the selector Selectable driving positions Normal position of the selector lever and current driving position Software lock: deactivate by pressing Selector Lever Release Button E681 Software lock: deactivate by pressing the foot brake1) Mechanical locking by Shift Lock Solenoid N110– Deactivate by pressing Selector Lever Release Button E681 Note: an acknowledgement tone sounds whenever driving position R is selected. Automatic gateA2 A1 X641_048Tiptronic gateX B1 B2 T+T T-641_050Speed-dependent transmission protection function A change in driving direction from D to R and vice versa is only possible at a driving speed below 5.0 mph (8 km/h). Upwards of a driving speed of 5.0 mph (8 km/h), a transmission protection function prevents the travel direction from being reversed.641_0491) he orange-colored software lock is activated in driving position N after about one second. This allows quick-changing of the driving position from D to R and T vice versa without applying the brake. The makes it possible, for example, to free a stuck vehicle by rocking it backwards and forwards and makes it easier to shift driving position when maneuvering.44 Component overviewHandle for selector lever top sectionSelector Lever Release Button E681 P button – Parking Lock Button E816 with Parking Lock Indicator Lamp. K320 illuminates the P button and is brightly lit when the parking lock is active.Handle for selector lever bottom section with selector lever gateSelector Lever Transmission Range Display Y5Selector mechanism coverPlug connection E Selector leverPlug connection C Plug connection A Selector mechanism (Selector Lever E313)641_051Selector Lever Release Button E681 E681 is used to release the selector lever lock. It has two shift elements for reliability and diagnostics. If E681 fails, it is considered actuated. The red and blue locks (illustration 641_048) are disabled and a DTC is registered. A message is displayed in the DIS for the driver. The selector lever can be moved out of the P and N positions while pressing the foot brake.Parking Lock Button E816 The P button is for manual deactivation of the parking lock. The parking lock can only be activated if the vehicle is traveling less than 0.6 mph (1 km/h). E816 has three shift elements for reliability and diagnostics. Its status is transferred to Selector Lever Sensor System Control Module J587 via two interfaces. In the event of a fault, a DTC is registered and a message appears in the DIS to alert the driver. The parking lock can only be engaged by the Auto P function.45 Transmission functionsAuto-P functionThe parking lock is operated electro-hydraulically. This allows the TCM to automatically engage the parking lock which in turn enhances operating ease. The Auto-P function engages the parking lock automatically (P-ON position) if: ›› The vehicle is stationary – travelling at a speed of less than 0.6 mph (1 km/h). ›› One of the following driving positions is engaged: D, S, R or M. ›› The engine is shut off – terminal 15 off. The parking lock can also be engaged by the driver by pressing the P button, provided that the vehicle is travelling slower than 0.6 mph (1 km/h). The parking lock is disengaged automatically (P-OFF position) if the engine is running and driving position D, S, R, N or M is selected. After 19 minutes the following message is displayed in DIS: "Start engine to remain in N." together with a warning tone. If this instruction is not followed, the parking lock will be engaged after 20 minutes and the system will shut down. If a vehicle speed signal is detected during this period, the period will be extended according to the driving time of the vehicle until a stationary time of at least 5 minutes is detected. During the stopping period in the P-OFF position, electrical power is consumed by the activity of control modules, bus operation and the holding magnet. If the vehicle is held stationary for a lengthy period of time, the battery may become discharged to the extent that the parking lock automatically engages itself. If it is necessary to hold the parking lock in the P OFF position for longer, the parking lock emergency release mechanism must be actuated (refer to page 50).Activating driving position N (P-OFF position)To be able to briefly move the vehicle without the parking lock for example, in a car wash, automatic engagement of the parking lock can be prevented. A condition for this is that the selector mechanism, the P button and the transmission are functioning properly. To activate the P-OFF position, driving position N must be selected when the engine is running, and then the engine must be shut off. When the ignition is switched off, engagement of the parking lock will be suppressed for 20 minutes.Tip shifting in D/SManual gearshifts can be performed at any time using the shift paddles on the steering wheel (tiptronic steering wheel) in driving positions D/S. If the tiptronic steering wheel is operated, the transmission runs continuously in manual mode (tiptronic mode). There are two options for returning to automatic mode: ›› Pull the selector lever back one position (position B1). ›› Move the selector lever into the tiptronic gate and back into the automatic gate.Launch control programThe Launch Control Program regulates the maximum acceleration of the vehicle from a standing start. Refer to the Owner’s Manual for operating instructions and other information.46 Special features of the tiptronic steering wheelThe following functions can be selected in the Audi R8 using the shift paddles on the steering wheel: ›› If both shift paddles are operated simultaneously while the engine is running, driving position N is selected (while moving and when the vehicle is stationary). ›› When the vehicle is stationary, the driver can shift from driving positions P, R, N to M1 by actuating the Tip+ shift paddle with the brake applied. ›› If the Tip+ shift paddle is continuously actuated while driving, the vehicle shifts into the highest available gear, for example, from 3rd to 5th gear. If the Tip- shift paddle is continuously actuated, the vehicle shifts into the lowest available gear, for example, from 7th to 3rd gear. ›› If a system malfunction has occurred in the selector mechanism, the driver can select driving position D with the Tip+ shift paddle when the vehicle is stationary while pressing the brake pedal. N can be selected by actuating. both shift paddles simultaneously. Reverse gear is not available. These additional functions of the tiptronic shift paddles are made possible by the redundant transfer of the shift commands from both shift paddles. The shift commands are first transmitted by CAN data bus to Transmission Control Module J217 and additionally by 2 separate wires to Automatic Transmission Control Module 2 J1006. This information is, in turn, sent from here to J217 by CAN data bus.Tip -Tip +641_05247 Audi drive select – transmission setupsIn addition to the well-known Audi drive select modes, comfort – auto – dynamic – individual1), the Audi R8 has a performance mode. Performance mode itself has three characteristics – snow, wet and dry. These characteristics allow the handling systems to be better adapted to the road surface conditions, that is, the friction between the tires and the road surface. The Audi drive select handling system utilizes the electronic stability control (ESC) system in performance mode.The comfort, auto and dynamic modesThe comfort and auto modes are identical regarding transmission setup. The shift points and the gearshifts are comfort-oriented. In dynamic mode the sport program S is selected in the transmission. In the sport program the shift points are at higher engine speeds and shift times are reduced. This makes for better power delivery and more noticeable gearshifts. The overview on page 49 shows the effects of the various Audi drive select modes on the transmission setup.1)In individual mode, the driver can choose a transmission setup independent from other vehicle systems.snowwetdrylast mode Performancelast mode drive selectcomfortautodynamicindividualKey: Performance button Performance button adjusting ring Audi drive select button/MMI turn-and-press knob Terminal 15 change-over641_038Performance mode In performance mode, the transmission setup is extremely sporty. This means that the transmission works to maximize power delivery from the engine. Comfort plays a secondary role here. Gearshifts are performed at very high engine speeds, and the shift times are extremely short and noticeable. Performance mode can only be activated and operated using the Performance button on the steering wheel. The Performance button allows the driver to activate or deactivate performance mode directly and in any Audi drive select mode.Note Please note that the stabilization functions of the ESC and TSC systems are limited after activating performance mode. You should only activate performance mode if you have the necessary driving skills and the traffic conditions permit.48 Performance button The Performance button is a touch switch with an adjusting ring. The adjusting ring is used to select the snow, wet and dry modes. These modes do not, however, have different transmission characteristics. Performance mode is standard in the V10 plus and optional for the V10.Audi drive select button Performance button with adjusting ring for selecting the snow, wet and dry modes641_054Overview of transmission setups available with Audi drive selectAudi drive select Mode Transmission setups and functions Driving position5) Shift characteristics Automatic upshifting in M mode Downshift during‑kickdown in M mode Modified accelerator map, increased idling and driveaway speed Launch control program No D normal – – comfort auto dynamic = sport program M1) – Yes Yes S sporty – – MS1) – No No Performance No distinction is made between dry, wet and snow S+ super sporty – – MS+1) – No NoM1) – Yes YesD normal – –normal Nosportysuper sportyYes – with automatic upshift into M and with the sportiest shift sequence and shortest possible shift time Yes C – B No C – Yes B No D –Blipping the throttle during downshift Shift sequence/shift time Return to automatic mode after actuating the tiptronic shift paddles Engine start/stop mode Cylinder-on-demand4)No A NoYes C –No A NoYes YesNo NoKey to shift sequence: A B C D Comfort-oriented overlapping gearshift with engine torque intervention3) Shift-time-oriented overlapping gearshift with maximum engine torque intervention High-speed overlapping gearshift with maximum engine torque intervention – specially adapted for tiptronic operation Fastest possible overlapping gearshift with maximum engine torque intervention and utilization of engine drag torque during upshifting denotes: manual shift program tiptronic, MS denotes: manual shift program tipt