TECHNICAL DOCUMENTATION
SSP 990393 – The 2019 Audi A8 Driver Assistance Systems

This PDF is currently unavailable.
Read document text
The 2019 Audi A8 Driver Assistance SystemseSelf-Study Program 990393Audi of America, LLC Service Training Created in the U.S.A. Created 06/2018 Course Number 990393 ©2018 Audi of America, LLC All rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC. Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.Revision: June 20, 2018iiIntroduction1The new Audi A8 driver assist systems 1 New driver assistance systems for longitudinal and lateral control 23rd generation camera-based traffic sign recognition system 43 Rear radar based driver assistance systems 44New features of side assist Turn assist function of side assist Use of turn assist in other traffic scenarios New features of the exit warning system New features of cross-traffic assist 45 46 47 48 49Active lane departure warningSwitching on and off Displays Master control module44 5 5Adaptive cruise assistIntroduction Displays and operation66 7Intersection assistFunctional description Intersection assist sensors Warnings of intersection assist Driver information System networking5050 51 52 53 54Longitudinal controlOverview Predictive efficiency assist1010 12Lateral control16New features of the vehicle's lateral control function 16 Functional configuration and sensors required 18 Control modules partnered to adaptive cruise assist 20Driver Assistance Systems Control Module J1121 56Versions Installation location of J1121 J1121 and its inputs J1121 – Version A0 J1121 – Version A J1121 – Version B J1121 – Version C 56 57 58 60 61 62 64Emergency assist22Function 22 Time sequence of active emergency assist processes 23 Time sequences of emergency assist processes during vehicle operation without assist systems activated 24 Time sequence of emergency assist processes when driving with adaptive cruise assist 26Laser Distance Regulation Control Module J1122 66Design and function Service 66 68Parking systemsParking system plus Rear view camera 3rd generation surround view cameras2727 29 31Control Module for Adaptive Cruise Control J428 69Design and function Operation and driver information Service operations 69 69 69Profile master for driver assistance systems 33Structure Operating concept System configuration 33 35 37eSelf-Study Programs Knowledge assessment70 712nd generation matrix LED high beam assistOperating the system and setting options Additional functions System networking3840 40 41iiiThe eSelf-Study Program (eSSP) teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a repair manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. For further information about maintenance and repair work, always refer to the current technical literature.NoteReferenceivIntroductionThe new Audi A8 driver assist systemsWhen it comes to the Audi A8, each model change marks the premiere of innovative solutions and new automotive systems. Each new Audi A8 model broadens the spectrum of driver assistance systems and extends the range of situations in which drivers are assisted by cutting-edge technology. The 5th generation of the Audi A8 includes new features such as intersection assist - a system that assists drivers in impaired visibility situations such as at intersections and obscured exits. The system helps the driver to avoid collisions with cross-traffic ahead of the vehicle by issuing several different types of warning. Adaptive cruise assist is also featured for the first time in the Audi A8. It assists the driver by providing longitudinal and lateral control assistance over a continuous speed range from 0 to 155.3 mph (0 to 250 km/h). This system combines several driver assistance systems featured previously in other Audi models. A new laser scanner is being used for the first time. It is located at the front end of the vehicle and enhances the performance of existing systems by precisely surveying the area in front of the vehicle. New driver assistance systems would not be possible without it. The 2019 Audi A8 utilizes, for the first time at Audi, a central driver assistance systems control module which acts as the master control for multiple assistance systems. Its service designation is Driver Assistance Systems Control Module J1121. It replaces several control modules whose functions are now integrated in J1121. Several sensors are connected directly to J1121 but no longer utilize an in-car bus system. The sensor data is processed in J1121. This applies to the front camera for driver assistance systems and the four surround view cameras. In turn, J1121 receives data from the other sensors via the FlexRay bus. The fact that all sensor data is now available in a single control module means it is possible to supply functions with high-quality data on the area around the vehicle. This, in turn, is the basis for further improvements in the performance of the various driver assistance systems.1New driver assistance systems for longitudinal and lateral controlNew structureAt the launch of the 2019 A8, two new driver assistance systems were created from the three well-known assistance systems. In terms of the functionality of the individual systems there have been no fundamental changes, but the grouping of the systems is new. In addition, the newly created driver assistance systems have been given new designations.These are the three established driver assistance systems: 1. Audi active lane assist (AALA) Audi active lane assist aids the driver with lateral control of the vehicle by providing corrective steering inputs. The driver can accept the system's corrective steering inputs or override them at any time. With AALA, the driver can select from "early" and "late" corrective steering points in the MMI. The "early" corrective steering point corresponds to a lane assist system in that it tries to keep the vehicle in the center of its lane by continuously applying corrective steering inputs. The alternative to the "early" corrective steering point is the "late" corrective steering point. In this configuration, the system works to prevent the vehicle from unintentionally leaving its lane. When the vehicle approaches a lane boundary line, corrective steering torque is applied towards the center of the lane. A requirement for corrective steering inputs is that a turn signal has not been activated beforehand; this would indicate that the driver intends to change lanes. In addition to the corrective steering torque applied when crossing over a lane boundary line, the steering wheel vibrates. This function can also be deactivated in the MMI. An activated turn signal would, however, prevent the vibration warning as the system assumes again in this case that the driver intends to change lanes.Characteristic of the steering torque applied at the "early" corrective steering point as a function of vehicle position relative to the center of the lane668_001Characteristic of the steering torque applied at the "late" corrective steering point as a function of vehicle position relative to the center of the lane668_0022. Adaptive cruise control (ACC) Adaptive cruise control is an enhancement of the existing cruise control system. In addition to adapting the speed of the vehicle, the system also adapts to a variable distance to a vehicle ahead. When the vehicle approaches a vehicle driving ahead, ACC maintains the set distance to this vehicle. If no traffic is detected ahead, the system acts as a regular cruise control system. 3. Traffic jam assist Traffic jam assist helps the driver in traffic jam situations. It takes over longitudinal and lateral control of the vehicle up to a maximum speed of 37.2 mph (60 km/h). When traffic jam assist is active, the driver can let the system operate the accelerator and brake pedals. However, the driver must be able to take control of the vehicle again. Full responsibility for operating the vehicle still remains with the driver. The driver's hands must stay on the steering wheel when lateral control is active. The driver can accept or override the steering torque applied by the system. In the case of the ACC system, the driver is still required to operate the accelerator and brake pedals in certain situations. The process of vehicle speed adaptation is also referred to as longitudinal control. An active Adaptive cruise control system provides for longitudinal control of the vehicle whenever the momentary road and traffic conditions permit. The responsibility for longitudinal control of the vehicle, however, still remains with the driver.2The following two new driver assistance systems are offered in the Audi A8 :1. Active lane departure warning The working principle of the Active lane departure warning corresponds to that of the Audi active lane assist with "late" corrective steering point. It is offered in the Audi A8 for the first time as a separate function.2. Adaptive cruise assist Adaptive cruise assist combines three formerly independent systems - adaptive cruise control, Audi active lane assist with "early" corrective steering point and traffic jam assist - in a single system. The new driver assistance system offers continuous longitudinal and lateral control over a speed range from 0 to 155.3 mph (250 km/h). Because adaptive cruise assist is also a driver assistance system, the driver retains full responsibility for operating the vehicle even while the system is in use. It is offered in the 2019 A8 for the first time as an independent function.System configuration in the 2017 Q7 and 2017 A4/A5Audi active lane assist "late" corrective steering input "early" corrective steering input Adaptive cruise control Traffic jam assistActive lane departure warningAdaptive cruise assistSystem configuration in the 2019 A8668_0033Active lane departure warningThe lane departure warning system warns the driver when the vehicle is in danger of leaving its lane. A requirement for a lane departure warning is, however, that the driver has not indicated an intent to change lane by activating the corresponding turn signal. The system uses the turn signal to determine whether the imminent lane departure is intended or not. A warning is issued only if the system assumes that the lane departure is unintentional.A warning that the vehicle is about to cross over a lane boundary line can be issued in three different ways:1. By a corrective steering input towards the center of the lane by the system. 2. Through steering wheel vibration. 3. By highlighting the affected lane boundary line in red on the instrument cluster display.Notes on the warning mechanisms:›› When adaptive cruise assist with lane assist is active, no further further corrective steering inputs are provided shortly before the vehicle crosses over a lane boundary line. Active lane assist is already a protective mechanism, which prevents the vehicle from unintentionally leaving its lane by providing corrective steering inputs. ›› The steering wheel vibration warning can be switched on and off in the MMI. The current setting is saved as a custom setting when the ignition is switched off.Switching on and offThe lane departure warning can be switched on and off with a virtual button on the lower touch display. When the lane departure warning is off, a red bar is displayed over the function symbol. The lane departure warning is always switched off for only one Terminal 15 cycle. The lane departure warning is reactivated next time the ignition is switched on, regardless of whether the ignition was off or on when the lane departure warning was switched off. The steering assist button on the end of the turn signal stalk is of no relevance to the lane departure warning. It is used only to activate and deactivate the Audi active lane assist function of adaptive cruise assist.Lane departure warning is ON668_005Lane departure warning is OFF668_006Positioning of the virtual button for activating and deactivating the lane departure warning668_0044DisplaysThe current activation status of the lane departure warning is indicated by the function symbol in the instrument cluster or on the head-up display.The lane departure warning is OFF.668_007668_008The lane departure warning is ON but inactive. Possible reasons for this include driving at too low a speed or the absence of lane boundary lines.668_009668_010The lane departure warning is ON and active. The system is currently only able to detect the left lane boundary line. For this reason, a warning can only be issued when the vehicle leaves its lane to the left.668_011668_012The lane departure warning is ON and active. The system is currently able to detect lane boundary lines on the left and right.668_013668_014The lane departure warning is ON and active. The system is currently able to detect lane boundary lines on the left and right. As the vehicle is in danger of leaving its lane to the right, a warning is given.668_015668_016Master control moduleThe master control module for the lane departure warning system is the Driver Assistance Systems Control Module J1121. Version A0 of J1121 is used for this function.5Adaptive cruise assistIntroductionAdaptive cruise assist is a new driver assistance system, which is offered for the first time in the 2019 Audi A8 as optional equipment. It combines three formerly independent systems - adaptive cruise control, Audi active lane assist with "early" corrective steering point and traffic jam assist - into a single driver assistance system.System configuration in the 2017 Q7 and 2017 A4/A5Audi active lane assist "early" corrective steering pointAdaptive cruise control (ACC)Traffic jam assistAdaptive cruise assistSystem configuration in the 2019 Audi A8668_017With adaptive cruise assist, a combined longitudinal and lateral control assistance function is available for the first time at speeds between 0 and 155.3 mph (0 and 250 km/h). The term "longitudinal control" is generally understood to mean accelerating and braking the vehicle, while the term "lateral control" is generally understood to mean steering the vehicle. However, the driver's hands must stay on the steering wheel while the lateral control function is active. With adaptive cruise assist, both longitudinal and lateral control functions are available to the driver. However, the driver can also deactivate the lateral control function so that only the longitudinal control function stays active. This means that vehicle behaves in much the same way as previously when driving with ACC. The longitudinal control function in the Audi A8 is very similar to the 4th generation ACC system used on the 2017 Audi Q7, 2017 A4 and 2017 A5. With adaptive cruise assist, it is not possible to deactivate the longitudinal control function while the lateral control function is active.Traffic jam assist provides lateral control at speeds of up to 37.2 mph (60 km/h) when a traffic jam situation is detected. Audi active lane assist provides lateral control at speeds of 40.3 mph (65 km/h) and higher. This means that lateral control is interrupted when, for instance, a traffic jam situation clears up. This interruption in lateral guidance does not apply to the adaptive driver assistance system in the Audi A8 since lateral guidance is the task of only one assistance system and this system operates at speeds between 0 and 155.3 mph (0 and 250 km/h). Adaptive cruise assist is a driver assistance system, but the driver is still fully responsible for operating the vehicle. The driver's hands must stay on the steering wheel. The system assists the driver, but it does not release the driver from his responsibility. Adaptive cruise assist reduces the strain on the driver and makes for more comfortable driving.6Displays and operationActivating and deactivating adaptive cruise assistThe Audi A8 comes equipped with both the customary ACC control stalk and a button for activating steering assist on the end of the turn signal stalk. To use adaptive cruise assist, the ACC control stalk must be moved into the ON detent position. Adaptive cruise assist is activated and deactivated in the same way as the ACC function. The procedure for setting the desired speed and the desired distance to the vehicle ahead is also unchanged. The procedure for the resumption of adaptive cruise assist is also familiar: a short pull on the operating stalk.ACC control stalk668_018Button for activating steering assist668_019Switching lane assist on and offWhen adaptive cruise assist is active, the driver can decide whether or not to use the lane center holding function ("early" corrective steering point) of Audi active lane assist. Lane assist can be switched on and off by pressing the button on the end of the turn signal stalk. The corresponding function symbol in the instrument cluster indicates the ON status of lane assist to the driver.7Display of lane assist system statusThe lane assist function of adaptive cruise assist can have three different states:1. Switched on and active. 2. Switched on and inactive. 3. Switched off.If active, lane assist is deactivated when at least one of the following conditions is not or is no longer met: ›› The road on which the vehicle is travelling does not have lane boundary lines or the system is unable to detect such lines. Furthermore, there are no objects or structures which lane assist can use as alternatives to the lane boundary lines. ›› The lane is either too narrow or too wide. ›› A curve has a radius which is less than the required minimum radius. Display of lane assist system status The color of the two triangles on the left and right indicates the current status of lane assist. The two triangles denote lane assist. The status of the system is indicated in the following displays:1. In the driver assist display in the instrument cluster. The driver assist display is one of the display options. 2. In the adaptive cruise assist function symbol in the instrument cluster below the speedometer. 3. In the adaptive cruise assist function symbol in the optional head-up display.›› The system detects no hands on the steering wheel over a defined period of time. ›› The front camera is unable to supply lane assist with images of sufficient quality. This can occur, for example, due to glare on the camera lens or dirt build-up on the windshield.System statusColor of the two trianglesFunction symbolDriver assistance display"switched on and active"green 80 mph"switched on and inactive"white 80 mph"switched off"Neither of the two triangles is displayed 80 mphThe status of lane assist is always displayed together with information on the status of the longitudinal control function. To illustrate better how the various states of lane assist are displayed, the status of the longitudinal control function stays unchanged in the table above.The states of the longitudinal control function are: Adaptive cruise assist is switched on and active. The vehicle is currently driving in convoy, with adaptive cruise assist maintaining a preset distance to the vehicle ahead. The driver has set a maximum speed of 80.7 mph (130 km/h) for free flow of traffic.8Adaptive cruise assist adjustment optionsThe following settings can be made in the MMI under the system settings of the profile master for driver assistance systems: 1. Saving the last setting for time interval to vehicle ahead Using the ACC control stalk, the customer can set a time interval to a vehicle ahead for adaptive cruise assist. Five time interval options are available. These are: 1 second, 1.3 seconds, 1.8 seconds, 2.4seconds and 3.6 seconds. If saving the last value is not activated, a following distance of 1.8 seconds is set by default whenever the ignition is turned on. The last value is saved to the current user account.2. Predictive control The following settings for adjustment to the route ahead can be made under "Predictive control": ›› Deactivate adaptation to route ahead. ›› Slow, medium or fast adaptation to route ahead. ›› Use speed limit ›› on ›› with tolerance ›› off668_0203. Setting the driving program A driving program can be set for adaptive cruise assist. This driving program is not dependent on the current Audi drive select setting. The acceleration and braking behavior of the longitudinal control function of adaptive cruise assist varies depending on what driving program is set. The following driving mode options are available: ›› moderate ›› standard ›› dynamic668_0219Longitudinal controlOverviewIn the context of adaptive driver assist, the term "longitudinal control" refers to all controlled (driver-independent) longitudinally dynamic driving maneuvers such as acceleration, constant-speed driving and deceleration, while "lateral control" is provided by means of driver-independent steering inputs. The driver's hands must be on the steering wheel at all times, as monitored by a hands-off detection system. In the Audi A8, longitudinal control is provided by Control Module for Adaptive Cruise Control J428.668_022A key new feature is the use of a laser scanner for the detection of objects in front of the vehicle. The radar unit on the left-hand front end of the vehicle has been replaced by a laser scanner. This laser scanner supplies objectrelated data but does not provide a corrective function to the vehicle. A functional distinction must be made between the basic and additional ACC functions and the predictive functions in combination with the efficiency assist functions.668_023668_094Basic and additional functions ›› Maintaining a set distance to a vehicle ahead. ›› Cruise control in free flow of traffic. ›› ACC stop & go including start-off monitoring. ›› Distance indicator / distance warning. ›› Side assist. ›› Traffic jam assist. ›› Audi pre sense front*. ›› Collision avoidance assist*. ›› Turn assist*.Predictive functions in combination with efficiency assist ›› Adjustment to speed limits. ›› Adaptation to route ahead (cornering speed).* For more information about these features, please refer to eSelf-Study Program 990493,The 2019 Audi A8 Introduction.10New features for the basic and additional ACC functionsDriving program A new feature is the option for activating various driving programs in the MMI. The choice of mode - "moderate", "standard" or "dynamic" - defines the dynamic behavior of the vehicle when ACC mode is active. The choice of mode affects acceleration, behavior when following a vehicle ahead (driving in convoy) and cornering dynamics. When "moderate" is selected, the vehicle accelerates moderately. In comparison with the "dynamic" driving program, greater variation in distance to the vehicle ahead is allowed when driving in convoy. This makes for more harmonious, comfortable and relaxed driving.668_021If the driver selects the "dynamic" driving program, the full acceleration potential of the engine is used. The vehicle maintains a relatively constant distance to the vehicle ahead when driving in convoy.The "standard" driving program offers a suitable response for most driving situations as a "compromise" between "moderate" and "dynamic".Distance indicator / distance warning When ACC is switched off, the driver is informed about the momentary distance to a vehicle ahead and receives a warning if the distance set by the driver is undershot. The following three warning thresholds (time gaps) can be set: 1 second, 2seconds and 3 seconds.Traffic jam assist This function reduces the driver's workload by providing for longitudinal and lateral control of the vehicle. In the Audi A8 the traffic jam assist function is integrated in the adaptive cruise assist system and is no longer implemented separately. There is no longer any provision for functional deactivation at a certain maximum speed. Only one vehicle driving ahead had to be detected to activate the function in the Audi A8. The activation and abort conditions have also been minimized. Refer to the Owner's Manual for further details.668_025ReferenceFor detailed information about ACC functions, refer to eSelf-Study Program 960163,The 2017 Audi Q7 Running Gear and Suspension System and eSelf-Study Program 979443, Audi ACC Systems.11Predictive efficiency assistOverviewModels equipped with Navigation Plus also have efficiency assist. This function assists the driver by prompts aimed at promoting an efficient driving style. If the vehicle is also equipped with adaptive cruise assist, longitudinal control will implemented predictively. The “master” for this function is Control Module for Adaptive Cruise Control J428. This assistance system uses the predictive route data of the vehicle navigation system to control the vehicle's longitudinal dynamics, with the aim of promoting an efficient driving style and reducing the driver's workload. Depending on the MMI setup, speed limits, route profiles (corners, intersections etc.) and terrain topology (uphill and downhill gradients) are incorporated in the ACC control processes. The functional system components are, apart from the modifications listed below, identical to those in the 2017 Audi Q7. ›› Image processing is handled by Driver Assistance Systems Control Module J1121. The front camera supplies the image data which is transmitted to J1121 via LVDS bus. ›› In the Audi A8, the radar unit on the left-hand front end of the vehicle has been replaced by a laser scanner. This laser scanner supplies object-related data and does not have a corrective function. All longitudinally dynamic control processes are carried out by J428.Laser Distance Regulation Control Module (laser scanner) J1122Information Electronics Control Module 1 J794ADR sesnor (radar sensor)Object dataTransmission Control Module J217Measurement data for radar sensor - MMI input - Navigation data - Driving program (Audi drive select) - Coasting/ overrun curves - Speed characteristicsCoasting requestData Bus on Board Diagnostic Interface J533Control Module for Adaptive Cruise Control J428Engine Control Module J623- Coasting request - Acceleration/ deceleration request Object data Deceleration request ABS Control Module J104Driver Assistance Systems Front Camera R242Image dataDriver Assistance Systems Control Module J1121668_02612The adaptation function controls acceleration processes, constant-speed driving including coasting and engine shut-off as well as deceleration through engine torque reduction or ESC braking. The driver can select the parameters to be used for predictive control in the MMI. ›› ›› Use speed limit and/or Adaptation to route ahead668_020The predictive control function is activated by using either of the above functions. If both functions are activated, the system's full predictive longitudinal control capability will be available.Use speed limitThe function uses two different sources to determine the current speed limit: ›› The predictive route data for vehicle navigation. ›› The camera-based traffic sign recognition system. In an adaptation situation, both sources supply the same information. Due to temporary changes in speed limits (for example, due to road construction), the speed limits indicated by traffic signs may deviate from the data in the navigation system. In these cases, the speed limits indicated by the traffic signs have higher priority and are implemented. The 3rd generation camera-based traffic sign recognition system is used in the Audi A8. This advancement is based on the 2nd generation system used in the 2017 Audi Q7. In the 2nd generation system the information for display to the driver was supplied directly before reaching the applicable range or the relevant traffic sign, the information is now sent earlier. In favorable conditions, the ACC control module receives the information approximately 109.3 yd (100 m) before reaching the traffic sign and, on average, about 54.6 yd (50 m) in advance. This enables the system to react predictively to upcoming changes in the speed limit by controlling the above-mentioned functions (acceleration, constant-speed driving/coasting, deceleration/ braking).Speed limit (traffic sign)Speed limit (predictive route data)Driver Assistance Systems Front Camera R242Roof Antenna R216Driver Assistance Systems Control Module J1121Information Electronics Control Module 1 J794668_028Control Module for Adaptive Cruise Control J428ReferenceFor detailed information about the 2nd generation camera-based traffic sign recognition system, refer to eSelf-Study Program 970263, The 2017 Audi Q7 Driver Assistance Systems.13Adaptation to route aheadAs an add-on to the "adaptation to route ahead" function a desired cornering speed (slow, medium or fast) can also be preset in the Audi A8. This, in combination with the selected drive program (moderate, standard, dynamic), provides a range of individual settings. For example, the "moderate" driving program, in combination with the "slow" setting for "adaptation to route ahead", is the most comfortable setting for negotiating corners.668_029If the "dynamic" driving program is selected in combination with the "fast" setting for "adaptation to route ahead", the cornering dynamics are maximized. All other setting combinations provide dynamic response within the bounds of these threshold settings. An exception to this is the "efficiency" setting in Audi Drive Select, which additionally activates an efficiency-enhancing program of adaptive cruise assist independent of driver inputs.668_030A key control parameter is the measured value for lateral acceleration, which is acquired by the sensors in the airbag control module. Working on the basis of the curve radius contained in the predictive route data of the vehicle navigation system, the ACC control module determines the lateral acceleration and cornering speeds which correspond to the MMI settings. These parameters are controlled primarily by adapting the engine torque. Active braking operations are also initiated by ESC as required.668_020The "adaptation to the route ahead" function has been expanded to include another key function. When the control system is activated, the Audi A8 now also reacts to stop signs, the position of which is obtained from the predictive route data. The vehicle is not brought to a complete stop the until it reaches the sign, but is slowed down to a minimum driving speed of 9.3 mph (15 km/h). In this way, the driver is alerted to the right of way and is able to bring the vehicle comfortably and safely to a standstill at the stop line. Any braking maneuvers performed by the driver will deactivate the control function. The control function can again be activated by moving the button on the ACC operating stalk into the "Resume" position. The vehicle's speed is not reduced at intersections on roads with equal rights of way and at traffic lights. When driving on main roads which turn off to the left or right the cornering speed of the vehicle is also controlled at the intersection. If the vehicle leaves the main road while the route guidance function is active, the control function is adapted accordingly.14668_031668_032The following example uses a possible driving profile to show the proceses typical of the predictive control system. The driver has activated the "use speed limit" function, as well as the “intelligent coasting” function and the “adaptation to route ahead” function in the MMI.A: The vehicle is leaving an urban area. Before the new speed limit of 62.1 mph (100 km/h) is indicated to the driver, the ACC control module is notified by Driver Assistance Systems Control Module J1121 that the vehicle is about to leave the urban area. The ACC control module computes the amount of acceleration required and sends this information to the engine control module, which implements the required acceleration by increasing engine torque when the vehicle exits the urban area. B: The vehicle was accelerated to 61.2 mph (100 km/h) and is travelling at a constant speed on a near horizontal road surface. C: The vehicle is approaching a long downhill gradient. The ACC control module receives this information as predictive route data and computes the reduction in engine torque required to maintain the set speed. The ACC sends this torque request to the ECM so that it can be implemented. The road gradient and road resistance coefficients are factored into the calculation so that a constant driving speed is maintained even when coasting. The ACC then sends a coasting enable signal to the ECM, which, in turn, assigns this task to the TCM. The ECM also decides whether the engine is to be shut down during the coast phase. Coast phases are generated most frequently in the "efficiency" mode of Drive Select.D: The predictive route data of the vehicle navigation system indicates that the vehicle is approaching a corner. Taking the curve radius and the MMI settings for the driving program and route ahead as a basis, ACC computes how much lateral acceleration is required to negotiate the corner. As the driver has selected the "slow" option in the "Adaptation to route ahead" menu, the computed cornering speed allows the driver to comfortably negotiate the corner. As the "moderate" driving program has been selected, the braking and subsequent acceleration phases are correspondingly comfortable. Accordingly, the vehicle is braked by the resultant engine drag torque. If this braking effect is not suffiicent to achieve the required corner entry speed, the ESC is also "tasked" with braking the vehicle. E: After exiting the corner, the vehicle again accelerates up to the speed limit. A new limited speed zone of 49.7 mph (80 km/h) indicated by a traffic sign begins within a distance of about 56.4 yd (50 m). This sign is identified by the camera-based traffic sign recognition system. Although the predictive route data would allow a higher speed, the vehicle's speed is reduced to 49.7 mph (80 km/h) because traffic signs have a higher priority.The control processes are primarily aimed at providing the driving style desired by the driver - be it moderate, efficiency-oriented or dynamic - to ensure that the vehicle operates efficiently.The vehicle has been configured in such a way that the transitions and interactions between control operations are as harmonious as you would expect of an actual, experienced driver.668_033ABCDE15Lateral controlNew features of the vehicle's lateral control functionThe lateral control function of adaptive cruise assist provides the driver with steering assistance and reduces the strain while driving. This is a further development of the lane center guide function in Audi active lane assist. The focus of the development was on the availability of the lateral control function The lateral control function of adaptive cruise assist is now also available in situations where it is deactivated in Audi active lane assist on other Audi models. In the case of Audi active lane assist, which will be available in nearly all other Audi models starting from launch of the Audi A8, lateral control is based solely on the lane boundary lines. A consequence of this is that the lateral control function is not available full-time if road boundary lines are not continuous or absent. This also applies to lane boundary lines which are hard to detect due to road or weather conditions. The lateral control function of adaptive cruise assist in the Audi A8 has now been expanded so that it can under certain circumstances stay active even after the loss of lane boundary lines.Measures to increase the availability of the lateral control functionAdaptation to static structures and objects If the lane boundary lines end but structures and objects are detected in the path of the route, the lateral control function is able to adapt to these features. The software in the Driver Assistance Systems Control Module J1121 decides in each specific situation whether detected structures or objects are suitable. In principle, the system is able to adapt to the following structures and objects: ›› Crash barriers668_034›› Grassy areas ›› Curbs Adaptation to traffic ahead If the road boundary lines end and one or more vehicles is an appropriate distance ahead, it may be possible to continue using the lateral control function on the basis of these vehicles. The software in the Driver Assistance Systems Control Module J1121 decides whether the current traffic situation is suitable.668_03516Lane center guide function on roads without centerline markingsThis scenario shows a road with two lane boundary lines at the roadside. One lane is available for each driving direction, but there is no center-line marking. Adaptive cruise assist recognizes this scenario and divides the road into two lanes for its calculations. It implements the lane center guide function for the right lane, although this lane is not separated from the left oncoming lane by center-line markings. In this way, the lane center guide function can be offered without both lanes actually being divided by an physical line. Because of this, it is possible to provide lateral control in more situations than was the case prior to the launch of adaptive cruise assist. In this case, however, a lane departure warning can only be given on the right-hand side of the vehicle due to the absence of a center-line marking.668_036Increased comfort when negotiating cornersWhen a vehicle negotiates a corner with lane assist active, the vehicle has until now negotiated the corner in the center of the lane. When the line assist function of adaptive cruise assist in the Audi A8 is active, the planned line is shifted slightly towards the inside of the curve as this best reflects the steering behavior of most drivers.668_037!Note In the case of the lateral control function in the Audi A8 , the driver must keep both hands on the steering wheel. The driver is still fully responsible for lateral control of the vehicle. The system's corrective steering inputs are similar in character to a steering recommendation and can be overridden by the driver at any time.17Functional configuration and sensors requiredIn the case of adaptive cruise assist, there are two control modules of central importance to the system. These are: ›› Control Module for Adaptive Cruise Control J428 (master control unit). ›› Driver Assistance Systems Control Module J1121.J428 has the following tasks: ›› Is the master control module of adaptive cruise assist. ›› Is the master control module for the longitudinal control function of adaptive cruise assist. ›› Reading the data generated by the front radar sensor for monitoring the area in front of the vehicle. ›› Collecting the data measured by all vehicle sensors monitoring the area in front of the vehicle. All measurement data is saved to an internal memory card. ›› Implementing the longitudinal control function of adaptive cruise assist. ›› Controlling the system displays in the instrument cluster and in the head-up display. ›› Saving the system settings selected by the driver. ›› Processing the signals of various system controls. When buttons are pressed and the ACC control stalk is actuated, the corresponding signals are sent to the vehicle data bus by Steering Column Electronics Control Module J527.J1121 has the following tasks: ›› Is the master control module for the lateral control function of adaptive cruise assist. ›› Reading the images captured by Driver Assistance Systems Front Camera R242. ›› Lane recognition on the basis of the images captured by the front camera. ›› Object recognition on the basis of the images captured by the front camera. ›› Implementing the lateral control function. ›› Reading data from the front four ultrasound sensors (depending on the vehicle configuration, the data from the four front ultrasound sensors can also be read by Vehicle Electrical System Control Module J519 if version B of Driver Assistance Systems Control Module J1121 is installed.Sensors The following components are required by adaptive cruise assist: ›› Driver Assistance Systems Front Camera R242. ›› Control Module for Adaptive Cruise Control J428. ›› Right and Left Front Parking Aid Sensors (G252 to G255). ›› Driver Assistance Systems Control Module J1122. The following sensors are not required by adaptive cruise assist, but are used if installed: ›› Right and Left Lane Change Assistance Control Modules J769 and J770. ›› Parallel Parking Assistance Sensor (G568, G569, G716 and G717).18Lane Change Assistance Control Module J769Extended CANLane Change Assistance Control Module 2 J770Laser Distance Regulation Control Module J1122Driver Assistance Systems Control Module R242Driver Assistance Systems Control Module J1121FlexRay Channel BData Bus on Board Diagnostic Interface J533Lateral controlInfotainment CANControl Module for Adaptive Cruise Control J428 Sensor data fusion HMIInformation Electronics Control Module 1 J794Longitudinal control668_038Key: HMI Is the abbreviation for Human Machine Interface - the interface between the driver and the vehicle system. This interface includes both the system displays (system - driver) and the options for system operation (driver - system). G203 – G206 G252 – G255 G568 – G569 G716 – G717 R242 Rear Parking Aid Sensors Front Parking Aid Sensors Front Parallel Parking Assistance Sensors Rear Parallel Parking Assistance Sensors Driver Assistance Systems Control Module19Control modules partnered to adaptive cruise assistPower Steering Control Module J500 ›› Applies the steering torque requested by adaptive cruise assist to the steering. Information Electronics Control Module 1 J794 and Front Information Display Control Head J685 ›› The customer can configure the settings for adaptive cruise assist via these two control modules. These settings are transmitted via the vehicle bus system to Driver Assistance Systems Control Module J1121 and Control Module for Adaptive Cruise Control J428, which in turn put this information into action. ›› Sends the current user data to the vehicle bus system. When the ignition is switched off, adaptive cruise assist saves the current system settings to the last user.Engine Control Module J623 ›› The driveline coordinator in the ECM receives the acceleration torque requested by adaptive cruise assist. The driveline coordinator is a central software module which receives the requested acceleration values from various systems and prioritises the requests accordingly. ›› Provides engine braking assistance when braking torque is requested.Instrument Cluster Control Module J285 ›› Displays the adaptive cruise assist function symbol in the instrument cluster display and displays text messages on request. In addition, the customer can activate the driver assist display in the instrument cluster. Is a component part of the onboard computer displays.ABS Control Module J104 ›› Provides the current vehicle speed to the FlexRay bus. ›› Is responsible for the vehicle's braking and stop management system. The function of the stop management system is to keep the stationary vehicle at a standstill. After the ESC has kept the vehicle at a standstill for three minutes, the electrical parking brake is actuated in order to protect the brake system components against overheating.Vehicle Electrical System Control Module J519 ›› Sends the states of the turn signals to the vehicle bus system. When the turn signals are activated, lane assist is temporarily inactive since an intended lane change is assumed.Transmission Control Module J217 Driver Door Control Module J386 ›› Is required for the longitudinal control function of adaptive cruise assist. J217 implements the required gearshift operations at the request of the ECM. ›› Sends the status of the driver door contact switch to the bus system. If the driver's door is opened when adaptive cruise assist is active, adaptive cruise assist deactivates for safety reasons.Steering Column Electronics Control Module J527 ›› Reads the information from the ACC control stalk and from the Audi side assist button in the turn signal stalk and sends this information to the vehicle bus system. Windshield Projection Head Up Display Control Module J898 ›› Displays the adaptive cruise assist function symbol. Airbag Control Module J234 ›› Sends the crash signal to the vehicle bus system which is read by adaptive cruise assist. In the event of a collision, adaptive cruise assist deactivates.20FlexRay channel AFlexRay channel BPower Steering Control Module J500Engine Control Module J623ABS Control Module J104Transmission Control Module J217Laser Distance Regulation Control Module J1122Steering Column Electronics Control Module J527Driver Door Control Module J386Control Module for Adaptive Cruise Control J428Airbag Control Module J234Vehicle Electrical System Control Module J519Driver Assistance Systems Control Module J1121Data Bus On Board Diagnostic Interface J533Comfort/convenience systems CANInfotainment CAN Information Electronics Control Module 1 J794MIB CANInstrument cluster CANFront Information Display Control Head J685Instrument Cluster Control Module J285Windshield Projection Head Up Display Control Module J898668_03921Emergency assistFunctionEmergency assist has been designed for situations in which the driver has incurred an medical emergency and, for this reason, is no longer able to operate the vehicle. The task of emergency assist in this situation is to take over longitudinal and lateral control of the vehicle and bring it to a controlled stop in its own lane. If the vehicle is travelling at too high a speed as it approaches traffic ahead, braking power is increased to slow the vehicle down. In this way, the system attempts to avoid an impending rear-end collision or to reduce the severity of such a collision. When emergency assist is active, a series of in-car measures are taken in order to protect the driver and minimize the risk of a collision.During the braking operation the following measures are taken: ›› The hazard warning flashers are activated to warn other road users. ›› The seat belt is fully tensioned during the final standstill braking operation. ›› The windows and the panoramic sunroof close automatically If emergency assist fails to detect the driver's hands on the steering wheel for a defined period of time, it assumes than an acute emergency has occurred. A special software algorithm, the "hands-off detector", has been developed in order to detect this. This is a known feature of Audi active lane assist. Inducing the driver to take control of the vehicle A second, key function of emergency assist is to alert an inactive driver to take control of the vehicle by taking various measures. For this purpose, the system takes the following action before and during the braking maneuver: ›› Display of text messages in the instrument cluster. ›› Acoustic signal output. ›› Initiation of brake warnings. ›› Initiation of a strong emergency brake warning. ›› Brief tightening of the driver's seat belt. ›› Muting of infotainment system. Emergency assist master control module The master control module for emergency assist is Driver Assistance Systems Control Module J1121. The basic version A0 is sufficient for emergency assist. Connectivity to other driver assistance systems is not a mandatory requirement for emergency assist in the Audi A8. If adaptive cruise assist is not installed on the vehicle, longitudinal control of the vehicle is implemented using Driver Assistance Systems Front Camera R242.22After the vehicle has come to a standstill, the following measures are taken: ›› Selector position "P" is engaged. ›› The vehicle doors are unlocked. ›› The interior light is switched on. ›› An emergency call is sent.To facilitate hand-off detection, the signal from the steering torque sensor is analyzed in an ongoing basis. This characteristic tells the software whether or not the driver's hands are on the steering wheel. Use of the accelerator and brake pedal is a further criterion for driver inactivity.After all, it is also possible that the driver is distracted and, for this reason, is not concentrating on driving although able to drive. If the driver is ready to again take control of driving the vehicle, the driver can indicate this through any of the following measures: ›› The driver again actively takes over steering the vehicle. -or›› The driver applies the footbrake. -or›› The driver presses down on the accelerator.The longitudinal control function is required by emergency assist in order to increase braking power. The idea is, when possible, to avoid a collision with slower vehicles when traveling at a high rate of speed. In this case, R242 normally replaces the front radar sensor required for longitudinal control (J428 Control Module for Adaptive Cruise Control)and Laser Distance Regulation Control Module J1122.Time sequence of active emergency assist processesThe time sequence of the various emergency assist escalation phases are explained on the basis of two specific driving situations.Example 1:An Audi A8 is travelling at a speed of 62.1 mph (100 km/h) with emergency assist active. The driver operates the vehicle manually. Driver assistance systems which influence longitudinal and lateral control of the vehicle are currently not active. Phase 0: The driver operates the vehicle actively by means of steering inputs and by operating the accelerator and brake. Phase 1: The driver releases the steering wheel and does not press the accelerator pedal or the brake. Phase 2: Emergency assist detects an inactive driver and activates. The first measure taken is to activate the lateral control system, with the aim of preventing the vehicle from leaving its lane. For this purpose, the lateral control system activates the "late" corrective steering point. At the start of phase 2, the distance to the traffic ahead is also monitored. Phase 5: If driver inactivity continues, standstill braking begins at a rate of 2.5 m/s2. If a collision hazard is detected, the rate of deceleration can be increased to 3.5 m/s2. The system further intensifies its efforts to alert the driver to take control of the vehicle by issuing warning tones and a noticeable emergency brake warning. Further brake warnings accompany the standstill braking operation, and full tensioning of the driver seatbelt is initiated. The hazard warning flashers are also activated to alert nearby traffic to the critical situation. For safety reasons, the windows and sunroof are also closed. The following text message is displayed in the instrument cluster: "Emergency assist". automatic emergency stop performed" Phase 6: After the vehicle has been braked to a standstill, selector position "P" is engaged and the electronic parking brake is applied. After 5 seconds of braking, the central locking system is unlocked and the interior light is switched on. An emergency call is sent 15 seconds after the vehicle comes to a standstill. Emergency assist activation conditions ›› During manual vehicle operation, emergency assist can only be activated at speeds of 34.1 mph (55 km/h) or higher. After a speed threshold of 55 kph is exceeded, emergency assist can be activated at the earliest after 20 seconds. ›› Lane boundary lines must be detected. ›› After actuating a turn signal, emergency assist can be activated at the earliest after 15 seconds. ›› If the driver changes over from assisted driving to manual operation, emergency assist can be activated at the earliest after 20 seconds. ›› When the status of emergency assist changes from "active" to "inactive", emergency assist can be reactivated at the earliest after 20 seconds.Phase 3 begins when any of the following events occurs: ›› The lateral control system performs a first corrective steering input ("late" corrective steering point). -or›› The system detects an inactive driver over a period of at least 30 seconds. -or›› Corrective braking is initiated in response to a vehicle ahead.Phase 3: The following text message is displayed in the instrument cluster: "Emergency assist" . lack of driver activity detected". The lateral control mode changes from "late" to "early" (active lane assist). The vehicle starts to brake at a rate of deceleration of 0.3 m/s2. If a danger of collision with traffic ahead is detected, heavier braking is applied. Phase 3 takes between 7 seconds and 10 seconds depending on the speed of the vehicle. Phase 4: The rate of deceleration of the vehicle is now increased to 1.0 m/s2 and audio output is muted. The system starts to alert the driver to take control of the vehicle by displaying the text message: "Emergency assist: please take control of vehicle". It also issues an audible warning as well as brief brake and seatbelt warnings. Phase 4 takes between 5 seconds and 8 seconds depending on the speed of the vehicle.!Note The time and speed values specified in the diagram are situation-specific and are intended only as a guide. They may in reality deviate from the values specified.2324 First corrective steering input by lane departure warning Transition after speed-dependent time Emergency assist Phase 5 Emergency assist Phase 3 Lateral control of system with "early" corrective steering point Emergency assist Phase 4 The vehicle continues to drive in the center of the lane Vehicle has been braked to a stop Emergency assist Phase 2 Emergency assist Phase 6 Lateral control with "late" corrective steering input Braking at 0.3 m/s2 (faster in case of rear end collision hazard) Emergency assist: lack of driver activity detected v = 55.9 mph (90 km/h) v = 53.4 mph (86 km/h) - Audio output is muted v = 49.7 mph (80 km/h) Emergency assist: please take over Emergency assist: automatic emergency stop performed Braking at 1.0 m/s2 (faster in case of rear end collision hazard) Braking at 0.3 m/s2 (faster in case of rear end collision hazard) Emergency assist: automatic emergency stop performed v = mph km/h - The windows and the sunroof are closedTime sequences of emergency assist processes during vehicle operation without assist systems activated›› Adaptive cruise assist is either not installed or is off›› Emergency assist is set to "on" in the profile master for driver assistance systemsDriver removes hands from steering wheel and operates neither the brake nor the acceleratorEmergency assist is activatedNormal vehicle operation without active assist systems Phase 0Hands-off detection Phase 1Vehicle lateral control by driverVehicle without Lateral controlLongitudinal control of vehicle by driverVehicle without Longitudinal controlText messages on the instrument cluster displayVehicle speedv = 62.1 mph (110 km/h)v = 59.0 (95 km/h)- Park position P is engaged - The electric parking brake closed - The door is unlocked - The interior light is activated - An emergency call is sentKey:668_040A warning tone is outputA seatbelt warning is givenA brake warning is givenThe driver's seatbelt is fully tensionedAn emergency brake warning is givenExample 2:An Audi A8 with active emergency assist is travelling at a speed of 62.1 mph (100 km/h). The driver has activated adaptive cruise assist, which has taken over longitudinal and lateral control of the vehicle. Phase 0: Adaptive cruise assist is active and the driver has both hands on steering wheel. Phase 1: The driver takes hands off the steering wheel and then behaves passively. Phase 2: Adaptive cruise assist detects that the driver no longer has hands on the steering wheel and displays the text message "Adaptive cruise assist: lack of driver activity detected".A warning tone is given 15 seconds after the text message is displayed. A short time later, another five warning tones are given. Phase 3: Emergency assist activates and the vehicle is immediately braked at a rate of deceleration of 1.0 m/s2. Adaptive cruise assist is deactivated at the same time. The following text message is displayed in the instrument cluster: "Emergency assist: please take control of vehicle". The system starts to alert the driver to take control of the vehicle by issuing an acoustic warning as well as brief brake and seatbelt warnings. Audio output is also muted. Despite the fact that lateral control is active, the driver's hands must be on the steering wheel, which was also the case until time t = 0 seconds.Phase 4: If driver inactivity continues, standstill braking commences at a rate of 3.5 m/s2. The system further intensifies its efforts to alert the driver to take control of the vehicle by issuing warning beeps and a noticeable emergency brake warning. Further brake warnings accompany the standstill braking operation, and full tensioning of the driver seatbelt is initiated. The hazard warning flashers are also activated in order to alert nearby traffic to the critical situation. For safety reasons, the windows and the tilt/slide sunroof are also closed. The following text message is displayed in the instrument cluster: “Emergency assist: automatic emergency stop performed”. Phase 5: After the vehicle has been braked to a standstill, selector position "P" is engaged and the electronic parking brake is closed. After 5 seconds of deceleration, the vehicle's central locking system is unlocked and the interior light is switched on. Finally, an emergency call is sent 15 seconds after the vehicle comes to a standstill.!Note The time and speed values specified in the diagram are situation-specific and are intended only as a guide. They may in reality deviate from the values specified.2526 Request to take over is displayed Emergency assist is activated Emergency assist Phase 3 Emergency assist Phase 4 Adaptive cruise assist Phase 2 The vehicle is now braked to a standstill with increased braking power Vehicle has been braked to a standstill Emergency assist Phase 5 Lateral control of the vehicle by emergency assist The driver does not have his hands on the steering wheel Braking at 1.0 m/s2 (faster in case of rear end collision hazard) Adaptive cruise assist: lack of driver activity detected Emergency assist: please take over Braking at 3.5 m/s2 (faster in case of rear end collision hazard) Emergency assist: automatic emergency stop performed v = 46.6 mph (75 km/h) Emergency assist: automatic emergency stop performed v = 0 mph/km/h - The windows and the sunroof are closed - Park position P is engaged - The electric parking brake is closed v = 62.1 mph (100 km/h) v = 62.1 mph (100 km/h) - Audio output is muted - Adaptive cruise assist is deactivated - The doors are unlocked - The interior light is activated - An emergency call is sentTime sequence of emergency assist processes when driving with adaptive cruise assist›› Emergency assist is set to "on" in the profile master for driver assistance systemsDriver removes hands from steering wheelNormal vehicle operation with active adaptive cruise assist - Phase 0Adaptive cruise assist Phase 1Lateral control of the vehicle by adaptive cruise assist The driver has his hands on the steering wheelLateral control of the vehicle by adaptive cruise assist The driver does not have his hands on the steering wheelLongitudinal control of the vehicle by adaptive cruise assist (ACA)Text messages on the instrument cluster displayVehicle speedv = 62.1 mph (100 km/h)Key:668_041A warning tone is outputA seatbelt warning is givenA brake warning is givenThe driver's seatbelt is fully tensionedAn emergency brake warning is givenParking systemsParking system plusEvery Audi A8 worldwide is equipped with an audible and visual parking aid with at least eight ultra-sound sensors.Electrical configuration of parking system plusIn terms of electrical configuration, there are two different versions of parking system plus in the Audi A8 : 1. The first version uses Vehicle Electrical System Control Module J519 as the master control. The eight front and rear parking aid sensors and Front and Rear Parking Aid Warning Buzzers H14 and H 15 are connected to J519. The ultrasound sensors are 5th generation sensors, as used previously in other Audi models. 2. The second version uses Driver Assistance Systems Control Module J1121 as the master control. The eight front and rear parking aid sensors as welll Front and Rear Parking Aid Buzzers H15 and H22 are connected to J1121. Four additional lateral sensors are always installed in the version.Electrical configuration of version 1: Version 1 is implemented if the vehicle has version A0, A or B of the Driver Assistance Systems Control Module J1121.Control Unit 2 for Driving and Convenience Functions E794E890Instrument Control Module J285Display and operation CAN bus LIN busVehicle Electrical System Control Module 1 J519Comfort/convenience systems CAN 2Data Bus On Board Diagnostic Interface J533Infotainment CANFront Information Display Control Head J685MIB CANInformation Electronics Control Module 1 J794668_042Key: E890 G203 G204 G205 G206 G252 Parking Assistance System Button Left Rear Parking Aid Sensor Left Rear Center Parking Aid Sensor Right Rear Center Parking Aid Sensor Right Rear Parking Aid Sensor Right Front Parking Aid Sensor G253 G254 G255 H15 H22 Right Front Center Parking Aid Sensor Left Front Center Parking Aid Sensor Left Front Parking Aid Sensor Rear Parking Aid Warning Buzzer Front Parking Aid Warning Buzzer27Electrical configuration of version 2: Version 2 is implemented if the vehicle has version C of Driver Assistance Systems Control Module J1121 installed. The version of J1121 installed depends on the driver assistance systems ordered with the vehicle.Control Unit 2 for Driving and Convenience Functions E794E890LIN busVehicle Electrical System Control Module 1 J519Comfort/convenience systems CAN 2FlexRay channel A Driver Assistance Systems Control Module J1121 FlexRay channel B Version C Infotainment CAN Data Bus On Board Diagnostic Interface J533Display and operation CANFront Information Display Control Head J685MIB CANInformation Electronics Control Module 1 J794Instrument Cluster Control Module J285668_043Key: E890 G203 G204 G205 G206 G253 G254 G255 Parking Assistance System Button Left Rear Parking Aid Sensor Left Rear Center Parking Aid Sensor Right Rear Center Parking Aid Sensor Right Rear Parking Aid Sensor Right Front Center Parking Aid Sensor Left Front Center Parking Aid Sensor Left Front Parking Aid Sensor G568 G569 G716 G717 H15 H22 Left Front Parallel Parking Assistance Sensor Right Front Parallel Parking Assistance Sensor Left Rear Parallel Parking Assistance Sensor Right Rear Parallel Parking Assistance Sensor Rear Parking Aid Warning Buzzer Front Parking Aid Warning Buzzer28Rear view cameraElectrical implementation of the rear view camera systemThe rear view camera is one of the new driver assistance systems in the Audi A8 which does not require Driver Assistance Systems Control Module J1121. The processes of correcting the camera's wide angle image, calibration and projecting reference lines onto the camera image are performed by Rearview Camera System Control Module J772. The image captured by the rear view camera is sent directly to Information Electronics Control Module 1 J794 over a shielded FBAS line. The image is then transmitted over shielded LVDS lines to Front Information Display Control Head J685.Control Unit 2 for Driving and Convenience Functions E794E890LIN busVehicle Electrical System Control Module 1 J519Parking aid master control moduleComfort/convenience systems CAN 2Rearview Camera System Control Module J772Extended CANData Bus On Board Diagnostic Interface J533Shielded FBAS lineInfotainment CANInformation Electronics Control Module 1 J794MIB CANFront Information Display Control Head J685Two shielded LVDS line pairs668_047Key: E890 Front Information Display Control Head29System activationThe rear view camera can be activated by selecting reverse gear, pressing Parking Assistance System Button E890 or through automatic system activation.668_048Parking Assistance System Button E890Washer jetThe rear view camera is prone to being obstructed by dirt build-up under certain ambient conditions. For this reason, the Audi A8 has a washer jet for cleaning the camera lens.Cleaning the camera lensThe process of cleaning the c