TECHNICAL DOCUMENTATION
SSP 990613 The 2012 Audi A6 Vehicle Introduction

This PDF is currently unavailable.
Read document text
Self-Study Program 990613The 2012 Audi A6 Vehicle IntroductionAudi of America, LLC Service Training Printed in U.S.A. Printed 4/2011 Course Number 990613 ©2011 Audi of America, LLC All rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC. Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Exterior Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Occupant Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .113.0L V6 TFSI Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Innovative Thermal Management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 ATF Heating / Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 2.0L TFSI Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 ATF Cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18Power Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20Suspension System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Axles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Electromechanical Steering. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Brake System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 ESP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Audi Drive Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27Electrical System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28Power Supply Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Fuses and Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Control Module Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Exterior Lighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Rear Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Rear Lights at Night . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48iTable of ContentsClimate Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50Infotainment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Topology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 Radio Media Center (RMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 MMI Radio Plus (RMC). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 MMI Navigation Plus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Google Earth Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 WLAN Hotspot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Operating Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 MMI Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 MMI Display Swivel Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Sound Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Antenna Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64Head-Up Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Display Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 Windshield Projection Display Control Module J898 . . . . . . . . . . . . . . . . . . . . 68Self-Study Programs for the 2012 Audi A7 . . . . . . . . . . .72 Knowledge Assessment . . . . . . . . . . . . . . . . . . . . . . . . . . .73The Self-Study Program provides introductory information regarding the design and function of new models, automotive components, or technologies. The Self-Study Program is not a Repair Manual! All values given are intended as a guideline only. For maintenance and repair work, always refer to current technical literature.ReferenceNote!iiIntroductionThe lineage of the Audi A6 sedan begins in the late 1960s with the launch of the Audi 100. The impact of the Audi 100 was revolutionary, embodying what was to become a new innovative spirit for the Audi brand. With its classic, uncluttered design, the Audi 100 formed the cornerstone for many legendary Audi C-platform vehicles that would emerge in the 1970s, ‘80s, and ‘90s, each leaving a lasting mark and forecasting the future. In the process, the Audi 100 became the Audi A6. Through it all, timeless and innovative Audi design cues and technology redefined automotive elegance and sportiness for each new decade. The 2012 Audi A6 continues this tradition. Its Audi internal designation is C7, being the seventh generation of the company’s C-platform. Like its predecessors, the C7 design inspires and creates enthusiasm. The new Audi A6 is a remarkable sedan that blends comfort and sport characteristics seamlessly. It is both a practical car and a car that excites every time you turn the wheel. Many of the A6’s technology and comfort features have only been available previously in luxury class vehicles. What the Audi 100 began, the new Audi A6 takes to new levels.486_0641BodyExterior Dimensions57.2 in (1445 mm)37.3 in (949 mm)64.05 in (1627 mm) 73.7 in (1874 mm)486_01563.7 in (1618 mm) 82.1 in (2086 mm)486_01641 (104 .1 in 6m m)37.8 (962 in mm )35.9 in (916 mm)114.6 in (2912 mm) 193.5 in (4915 mm)42.9 in (1091 mm)478_031226.5 in (674 mm)57.4 in (1460 mm) 60.1 in (1527 mm)56.2 in (1429 mm) 58.7 in (1491 mm)46.2 in (1176 mm) 41.3 in (1050 mm)486_018Length Width Height Front track width Rear track width Wheelbase Curb weight Maximum gross weight193.5 in (4915 mm) 73.7 in (1874 mm) 57.2 in (1455 mm) 64.05 in (1627 mm) 63.7 in (1618 mm) 114.6 in (2912 mm) 3472.2 lb (1575 kg) 4750.9 lb (2155 kg)Front internal width Rear internal width Front headroom Rear headroom Loading width Load sill height Trunk capacity Fuel tank capacity Drag coefficient57.4 in (1460 mm) 56.2 in (1429 mm) 41.1 in (1046 mm) 37.8 in (962 mm) 37.3 in (949 mm) 26.5 in (674 mm) 18.7 cu ft / 35.1 cu ft (530 l / 995 l) 19.8 gal (75.0 l) 0.263OverviewThe body of the 2012 A6 is a hybrid, lightweight design. Aluminum components are used in addition to steel panels. The body-in-white has two aluminum cast components, the front strut mounts, as well as mild, high strength, modern high strength, and ultra high strength steel body panels.Mild steels High strength steels Modern high strength steels Ultra high strength steels Ultra high strength steels (hot-formed) Sheet aluminum parts Cast aluminum parts Extruded aluminum sections4486_0195Occupant ProtectionIntroductionThe occupant protection system in the 2012 A6 is comparable to that of the 2012 Audi A7, with individual components adapted to the A6. A safety belt warning feature for the rear passengers is new.Reference For more information about the occupant safety system of the 2012 Audi A6, refer to Self-Study Program 920603, The 2012 Audi A7 Occupant Protection, Infotainment, Climate Control, and Head-Up Display.6486_0117Components The following components are used in the 2012 A6 occupant protection system for the North American market: – Airbag control module – Adaptive driver and front passenger airbags – Front side airbags – Audi Sideguard (side curtain airbags) – Driver and front passenger knee airbags – Up-front airbag crash sensors – Door-integrated pressure type sensors for side impact detection – Acceleration-type sensors for side impact detection on the C-pillars – Front inertia-reel safety belts with pyrotechnic and electrically reversible belt tensioners and active belt force limiters – Battery interrupt igniter – Safety reminder for driver and front passenger – Safety belt switch, driver and front passenger – Seat occupancy sensor in front passenger seat (PODS) – Driver and front passenger seat position recognition – Rear passenger safety belt usage warningLegend: E24 E25 E258 E259 E609 G128 G179 G180 G256 G257 G283 G284 G551 G552 G553 G554 J234 J285 J533 J623 J706 J854 J855 Driver’s Seat Belt Switch Front Passenger Seat Belt Switch Driver Side Rear Seat Belt Switch Front Passenger Side Rear Seat Belt Switch Center Rear Seat Belt Switch Front Passenger Seat Occupant Sensor Driver Side Airbag Crash Sensor Front Passenger Side Airbag Crash Sensor Driver Side Rear Side Airbag Crash Sensor Front Passenger Side Rear Side Airbag Crash Sensor Driver Front Airbag Crash Sensor Front Passenger Front Airbag Crash Sensor Driver Belt Force Limiter Front Passenger Belt Force Limiter Driver Seat Position Sensor Front Passenger Seat Position Sensor Airbag Control Module Instrument Cluster Control Module Data Bus On Board Diagnostic Interface Engine Control Module Passenger Occupant Detection System Control Module Left Front Seat Belt Tensioner Control Module Right Front Seat Belt Tensioner Control Module K19 K75 K145 N95 N131 N132 N153 N154 N196 N197 N199 N200 N201 N202 N251 N252 N253 N295 N296 N490 T16 Seat Belt Indicator Light Airbag Indicator Lamp Front Passenger Airbag –Disabled– Indicator Lamp Driver Airbag Igniter Front Passenger Airbag Igniter 1 Front Passenger Airbag Igniter 2 Driver Seat Belt Tensioner Igniter 1 Front Passenger Seat Belt Tensioner Igniter 1 Left Rear Seat Belt Tensioner Igniter Right Rear Seat Belt Tensioner Igniter Driver Thorax Airbag Igniter Front Passenger Thorax Airbag Igniter Left Rear Thorax Airbag Igniter Right Rear Thorax Airbag Igniter Driver Head Curtain Airbag Igniter Passenger Head Curtain Airbag Igniter Battery Interrupt Igniter Driver Knee Airbag Igniter Front Passenger Knee Airbag Igniter Driver Airbag Release Valve Igniter Data Link Connector8A6_Airbag_USAa9Driver and Front Passenger Seat Belt Switches E24 and E25 E24 and E25 are integrated into the front safety belt buckles. These reed switches are components of the safety belt reminder system. If the safety belt is not buckled, the reed switch is closed. In this position, a magnet built into the tip of a plastic pin acts on the reed switch. If the safety belt is buckled, the reed switch is open. The inserted belt tongue lifts the plastic pin. The magnet no longer acts on the reed switch and it opens. Airbag Control Module J234 reads the resistance and determines if the safety belt is buckled or not.Plastic pinMagnet 484_010 484_011Rear Safety Belt Reminder After the ignition is switched ON, a status display for the rear safety belts (fastened/not fastened) appears for approximately 31 seconds in the Driver Information System of the instrument cluster. At each change in status, a new display appears for approximately 31 seconds. If a rear-seat passenger unfastens the safety belt while the vehicle is moving at a speed above 15.5 mph (25 km/h), an acoustic warning sounds once and the corresponding indicator in the display begins flashing for approximately 31 seconds. Airbag Control Module J234 receives the information whether the safety belts are fastened through the rear safety belt switches (E258, E259, E609.)Reed switchSafety belt fastenedSafety belt not fastened486_012Rear safety belt not fastened warning“terminal 15” ON OFF Not Fastened Fastened Active Visual warning OFF Acoustic warning Active OFF 15.5 mph (25 km/h) 15.5 mph (25 km/h) 486_013 10 Lights 31 seconds Blinks 31 seconds Lights 31 secondsSafety beltVehicle speedEngine3.0L V6 TFSI EngineTechnical FeaturesAdapted belt drive (without power steering pump)486_003Modifications to the 3.0L V6 TFSI Engine for the 2012 A6 Cylinder block Cylinders – New Innovative Thermal Management System (ITM) – Honed to a textured finish to reduce oil consumption and wear – Increased piston installation clearance – Reduced pre-stress on the third piston ring land Main bearing inserts Chain drive – Bearing surfaces coated with an additional wear-resistant layer designed to withstand composite friction – Chain tensioners reconfigured and adapted for reduced oil flow – Weight of intake valve camshafts reduced Camshafts – Cam contour revised – Weight of exhaust valve camshafts reduced – All camshafts are now composite construction Camshaft adjusters Valve gear Oil pump Spark plugs – Enhancements reduce leakage, resulting in reduced oil circuit pressure – Reduced spring forces – Smaller, consumes less power, and generates less friction – Heat ratings adapted for optimized combustionReference For further information about the design and operation of the 3.0L V6 TFSI engine, refer to Self-Study Program 925803, The Audi 3.0L V6 TFSI Engine with Roots Blower.11Specifications335.2 hp (250 kW) 301.7 hp (225 kW) 268.2 hp (200 kW) Power in hp (kW) Torque in lb ft (Nm) 234.6 hp (175 kW) 201.1 hp (150 kW) 167.6 hp (125 kW) 134.1 hp (100 kW) 100.5 hp (75 kW) hp (kW) 33.5 hp (25 kW) 0 1000 2000 3000 4000 5000 6000368.7 lb ft (500 Nm) 331.9 lb ft (450 Nm) 295.0 lb ft (400 Nm) 258.1 lb (350 Nm) 221.2 lb ft (300 Nm) 184.3 lb ft (250 Nm) 147.5 lb ft (200 Nm) 110.6 lb ft (150 Nm) lb ft (Nm) 36.8 lb ft (50 Nm) 7000 478_053Engine Code Engine type Displacement Maximum power Maximum torque Valves per cylinder Bore Stroke Compression ratio Powertrain Engine management Fuel grade Exhaust emission standardCGWB Six cylinder V engine with 90° included angle 182.7 cu in (2995 cc) 310 hp (220 kW) @ 5500–6500 rpm 325 lb ft (440 Nm) @ 2900–4500 rpm 4 3.32 in (84.5 mm) 3.50 in (89.0 mm) 10.5 : 1 quattro Simos 8 91 AKI ULEV 212Innovative Thermal ManagementInnovative Thermal Management (ITM) for the 3.0L V6 TFSI engine is similar to the system designed for the 2011 Audi A8 4.2L V8 TFSI. It is an electronically controlled system designed to optimally distribute engine heat flow. The system is controlled by the Heat Manager, a recently developed software module fully integrated into the engine control module (ECM). The engine coolant is distributed on demand between the engine, transmission, and passenger compartment by a system of valves. To ensure maximum comfort, the demands of the heating and climate control systems are evaluated at all times. The climate control and transmission control modules communicate their heating requirements to the ECM via CAN bus. These heating requirements, together with the engine heating request from the ECM, are then analyzed and prioritized. ITM components are activated accordingly. During phase one of operation, the engine coolant does not circulate. This results in the stationary coolant temperature increasing faster than if it was circulated, thus reducing frictional losses in the engine. After the non-circulation phase, engine coolant is used to rapidly heat the ATF via a heat exchanger. The coolant is directed by an electrical control valve actuated by the Transmission Control Module. A mixing phase is cycled by the ECM to ensure that hot engine coolant is not circulated immediately, which would impair the frictional properties of the engine. Passenger Compartment Heating The stationary coolant phase normally takes approximately 120 seconds. However, there are circumstances where stationary coolant is unwanted, for example, when the Defrost button is pressed. Warm coolant flows immediately to the heater in order to prevent the windshield from fogging up. If the heater does not need any energy to heat the vehicle interior (at warm ambient temperatures), the climate control module does not send a heating request. Transmission Heating/Cooling The ATF is heated and cooled as needed, and is only cooled to the temperature level of the engine coolant.ITM System Technical Summary – Active coolant pump Two sensors: – Engine Temperature Control Temperature Sensor G694 – Coolant Temperature Sensor G62 – ATF heating/cooling – Heating cut off – Thermostat opens at 188.6°F (87°C)Reference For more information about the Innovative Thermal Management system of the 3.0L V6 TFSI engine, refer to Self-Study Program 990203, The 2012 Audi A7 Introduction.13ATF Heating / CoolingOverview The software for the Innovative Thermal Management (ITM) system is located in the Engine Control Module. It receives information about ATF temperature from Transmission Control Module J217.1 Cooled coolant 2 V50 Cooled coolant (charge air coolant) Warmed coolant 3 4 Warmed coolant (charge air coolant) ATF 2 2ITM controls heating and cooling of the ATF. The ECM gives the TCM the command to open or close the Transmission Fluid Cooling Valve N509.N5095G6945 67N489 8F265 J671G62 J2939 486_068 10 11Legend: G62 G694 J293 J671 N489 N509 V50 V1881 2 3V188Engine Coolant Temperature Sensor Engine Temperature Control Temperature Sensor Coolant Fan Control Module1 Coolant Fan Control Module 21 Cylinder Head Coolant Valve1,4 Transmission Fluid Coolant Valve2 Coolant Recirculation Pump3 Charge Air Cooling Pump1Controlled to ECM J623 Controlled by TCM J217 Controlled by Climatronic Control Module J255 4 Switches the engine coolant pump1 2 3 4 5 6 7 8 9 10 11Heat exchange (passenger compartment) Bleeders Quick connector (black) ATF heat exchanger Charge air intercooler Engine coolant expansion bottle Active engine coolant pump Engine oil cooler Radiator Low temperature cooler for coolant Low temperature auxiliary cooler for engine coolant14Operation 1. Start Phase When the engine is started cold, ECM J623 commands Transmission Control Valve J217 to close Transmission Fluid Cooling Valve N509. Coolant circulation for the ATF heat exchanger is interrupted. Initially, the variable coolant pump is inactive. Outside temperature, engine temperature, engine speed (rpm), and the heat requirements of Climatronic are criteria for switching to active. The ITM system decides when the coolant pump is switched to active through valve N509. 2. Heating the ATF When the coolant pump is switched to active, ITM compares the engine temperature measured Engine Temperature Control Temperature Sensor G694 with the ATF temperature. As soon as ATF temperature is 9°F (5°C) lower than the rising engine temperature, the ECM commands the TCM to open N509. Circulation for the ATF heat exchanger is opened. The ATF is heated. 3. Normal Operation When the TCM reports an ATF temperature of approximately 183.2°F (84°C) to the ECM, the ECM commands the TCM to close N509 again, interrupting coolant circulation for the ATF heat exchanger. The ATF has reached the desired operating temperature and is neither heated nor cooled. This continues up to an ATF temperature of about 221°F (105°C). 4. Cooling the ATF If ATF temperature exceeds 221°F (105°C), the ECM commands the TCM to open N509, which opens circulation for the ATF heat exchanger. The ATF is cooled by the 185°F (85°C) engine coolant. Once ATF temperature has reached about 194°F (90°C), conditions for normal operation are met again. The ECM issues the command to the TCM to close N509 again.Return from heat exchangerBlack quick-connect valveReturn486_069ATF heat exchanger Transmission Fluid Cooling Valve N509 – Current applied: valve closed, coolant flow interrupted – Current not applied: valve open, coolant flow unrestricted Supply152.0L TFSI EngineTechnical Features – Exhaust gas turbocharging – Four-valve cylinder head with a camshaft adjuster on the intake side and Audi valvelift system on the exhaust side – Modified belt drive (no power steering pump) – Chain-driven camshafts – Dual path intake manifold – Flow controlled oil pump – Improved high pressure fuel injectors486_007Reference For additional information about the design and construction of this engine, refer to Self-Study Program 921703, The 2.0L Chain-Driven TFSI Engine.16Specifications201.1 hp (150 kW) 181.0 hp (135 kW) 160.9 hp (120 kW) 140.8 hp (105 kW) 120.6 hp (90 kW) Power in hp (kW) Torque in lb ft (Nm) 80.4 hp (60 kW) hp (kW) 40.2 hp (30 kW) 20.1 hp (15 kW) 118.0 lb ft (160 Nm) lb ft (Nm) 59.0 lb ft (80 Nm) 29.5 lb ft (40 Nm) 100.5 hp (75 kW) 295.0 lb ft (400 Nm) 265.5 lb ft (360 Nm) 236.0 lb ft (320 Nm) 206.5 lb (280 Nm) 177.0 lb ft (240 Nm) 147.5 lb ft (200 Nm)010002000300040005000600070008000 486_008Engine Code Engine type Displacement Maximum power Maximum torque Valves per cylinder Bore Stroke Compression ratio Powertrain Engine management Fuel gradeCDNB Four cylinder inline engine 121.0 cu in (1984 cc) 211 hp (157 kW) @ 4000–6000 rpm 250 lb ft (339 Nm) @ 1500–3900 rpm 4 3.24 in (82.5 mm) 3.65 in (92.8 mm) 9.6 : 1 Multitronic Bosch MED 17.1 91 AKI17ATF CoolingOverview On vehicles with the 2.0-liter inline 4-cylinder engine, there is no ATF heating.1Above an engine coolant temperature of about 176°F (80°C), the cooling circuit for the ATF heat exchanger is integral with the cooling circuit for the engine through the thermostat.Cooled engine coolant Warm engine coolant ATF 3 42V50N8256 7G62F26589 G62 V51J671J29310Legend: G62 F265 J293 J671 N82 V50 V511 2486_067Engine Coolant Temperature Sensor Map Controlled Engine Cooling Thermostat1 (opening begins at approximately 203°F [95°C]) Coolant Fan Control Module1 Coolant Fan Control Module 21 Coolant Shut-Off Valve2 Coolant Recirculation Pump2 After-Run Coolant Pump11 2 3Controlled to ECM J623 Controlled by Climatronic Control Module J255Heat exchange (passenger compartment) Bleeder ATF engine coolant regulator (opening begins at approximately 176°F [80°C] 4 ATF heat exchanger 5 Quick connector with restrictor, gray 6 Coolant expansion bottle 7 Water pump 8 Turbocharger 9 Engine oil cooler 10 Radiator18Quick Connector with Restrictor The quick connect with restrictor (gray) is used in vehicles with the 2.0L, 4-cylinder TFSI engine. A quick connect without restrictor (black) is used on vehicles with the 3.0L V6 TFSI engine. If the quick connect without restrictor (black) is installed in vehicles with the 2.0L TFSI engine instead of the specified quick connect with restrictor (gray), the cooling performance of the ATF heat exchanger will be reduced. This can cause elevated ATF temperatures. ATF Thermostat An ATF coolant regulator is installed in the coolant return of the ATF heat exchanger. A groove in the valve seat allows a very small permanent flow of engine coolant. If coolant temperature rises, the wax in the thermal element is heated and expands. As a result, it opens the valve seat through the lift rod and coolant circulation is enabled when the coolant temperature reaches 176°F (80°C).Quick connector with restrictor (gray)Thermal element with lift rodDirection of Flow When installing the ATF coolant regulator, strict attention must be paid to the direction of flow, which is identified by an arrow on the regulator housing. In the event of incorrect installation, regulation is undesirably affected and ATF cooling is obstructed. If the groove in the valve seat is contaminated, the very small permanent flow of coolant is interrupted, and the thermal element is not properly heated. The valve seat remains closed and the ATF is not cooled. If there is excessive ATF temperature, then coolant and fluid circulation to the ATF heat exchanger, as well as the coolant regulator, must be checked.Coolant regulatorReturn from heat exchanger ClosedOpenedReturn486_070Supply19Power TransmissionOverviewThe 2012 A6 is introduced with the 8-speed 0BK automatic transmission. This transmission was designed specifically for the North American market. It is the same transmission used in the 2011 A8 but does not feature the “shift-by-wire” control system. Instead, it uses a cable operated mechanical selector.478_0180BK transmissionAxle flange with new sealing and assembly design (as in the B8 series)0BF sport differential (not offered with 0BK transmission)Reference For more details about the mechanical operation of the 0BK transmission, refer to Self-Study Program 950103, The 2011 Audi A8 Power Transmission.20Splined prop shaft: Weight reduction by elimination of the bolted flange connectionForward mounted final drive (as with the B8 series)478_010478_011 478_027Multitronic 0AW – Step-less transmission for future frontwheel drive models with engines rated up to 295 lb ft (400 Nm)0B5 S tronic 7-speed transmission – 7-speed dual clutch transmission for future use on quattro models21Suspension SystemOverviewOne of the key development goals for the A6 was to provide outstanding agility, driveability and driving enjoyment while also offering a high standard of safety and comfort. This was made possible by adopting the proven design of Audi’s five-link front suspension combined with a selftracking trapezoidal-link rear axle. A steel-sprung suspension with conventional shock absorbers is standard. The A6 uses the same powertrain design that was first used on the Audi A5, with the axle drive positioned ahead of the differential to provide a large wheelbase and small front overhang. Mounting the steering gear on the subframe in front of the front axle provides the necessary, exact steering response and a precise steering feel in every driving situation. Electro-mechanical steering provides improved fuel economy in addition to allowing more functional options related to handling and control.478_073Production Control Number (PR)1BADescriptionTechnical ImplementationOfferStandard running gear /suspensionSteel suspensionSeries standard1BESports running gear /suspension Sports running gear /suspension S line (offered from quattro GmbH) Adaptive air suspension (not available at launch)Steel suspensionOption1BVSteel suspensionOption1BKAir suspensionOptionReference For further information about the suspension system of the 2012 A6, refer to Self-Study Program 990303, The 2012 Audi A7 Running Gear and Suspension.22AxlesFront Axle The A6 uses the five-link front suspension of the 2011 A8 as a starting point. The bearing pedestal that supports the upper wishbone has been integrated into the body shell. In addition to saving weight and increasing rigidity, this also reduces the fitting tolerances of the upper wishbones. Anti-roll bars and shock absorbers have been reconfigured to meet the design objectives of the A6.478_074Rear Axle The rear suspension design is based on the trapezoidal link rear axle used on the Audi Q5. Springs and shock absorbers are separated from one another, providing a large pass-through loading width and a flat load floor.478_07523Electromechanical SteeringOverview The new generation of electromechanical power steering used on the 2012 A7 is also used on the 2012 A6. The power assist is accomplished via an electric motor arranged concentrically in relation to the steering rack. This design was selected because it enables high performance capability with relatively small space requirements. The rack, electric motor, ball screw assembly, control module and necessary sensors are integrated into a compact unit. This complete steering system is approximately 35.2 lb (16 kg) lighter than earlier versions. The weight reduction means better fuel consumption and increased functionality with other vehicle safety and handling systems.Steering Torque Sensor G269Steering pinion Ball screw assemblyElectromechanical Power Steering Motor V187 with rotor positionPower Steering Control Module J500 Rack480_03324Brake SystemOverview The A6 brake system is similar in design and operation to that of the 2011 A8 and 2012 A7. An electromechanical parking brake is used at the rear. A high performance ESP by Bosch, which has an extended range of functions, provides a high standard of safety. As on the 2011 A8, Sensor Electronics Control Module J849 supplies information about vehicle dynamics for calculation of desired control operations. The system used in the A6 is identical to that of the A8.17” 2FNR 42 AL aluminum floating frame type caliper486_082 Rear wheel brakes combined with electromechanical parking brake (EPB)Sensor Electronics Control Module J849New ESP system by Bosch, with extended range of functionsTandem master brake cylinder with 8/9 inch tandem brake booster478_07225ESPThe 2012 A6 uses the 9th generation ESP Premium. The range of functions was expanded for the future use of dynamic steering. ABS Control Module J104 determines necessary steering intervention to assist vehicle stability. To do this, the values measured by the wheel speed sensors, the steering angle sensor, Sensor Electronics Control Module J794, and the rotor position sensor of the dynamic steering actuator are processed. When needed, J104 then “instructs” the control unit for Active Steering Control Module J792 to perform a steering correction, irrespective of the steering action by the driver. This feature will not be available during the 2012 model year.Pressure sensor Hydraulic moduleDiagnosis procedures are identical to those for the Audi A7. The innovative functions of wheelselective torque vectoring (for quattro drive) and the electronic locking differential (for front-wheel drive) are also used in the 2012 A7. The control module can be removed from the hydraulic unit for service and replaced separately. The installation operations must be performed in an ESD-protected workplace using special service tool VAS 6613.Valves Solenoid valves Control module Pump piston Electric motor 486_085Tire Pressure MonitoringAudi’s familiar second-generation tire pressure monitoring system is also used on the A6. The system is standard on this model worldwide and is identical to those already in use on other Audi models.486_08626Audi Drive SelectAudi Drive Select will also be offered on the 2012 A6. There are three modes: comfort, auto, and dynamic. The driver can select these via the MMI control panel and, for example, switch from a sport to a comfort driving mode. The drive can use the individual mode to configure the vehicle. For instance, a sport engine setup can be combined with light steering action. The model and option level dictates which systems can be configured by Audi drive select. In all cases, the engine, transmission, and steering systems are controlled.A6_AudiDriveSelectMode Characteristics comfort Engine/transmission balanced auto balanced dynamic sportAir suspension*comfortbalancedsportSteeringcomfortbalancedsportSport differential*balancedresponsivesportReversible belt pretensionersstandardstandardadapted activation timing*Not on US models at the introduction of the A6.Reference For more information about the Audi drive select system and its mode characteristics, refer to Self-Study Program 990203, The 2012 Audi A7 Vehicle Introduction.27Electrical SystemPower Supply OverviewRefer to current technical literature for exact fuse assignments and cable routing.Coolant Fan Control Module J293 and Coolant Fan Control Module 2 J671Alternator Power Steering Control Module J500 StarterFuse and relay carrier SD Jump Start TerminalFuse carrier SAVoltage distributor in plenum chamber Fuse carrier SB Fuse carrier SCGrounding point in spare tire wellFuse carrier SF Main fuse at battery positive terminalBattery Monitoring Control Module J367 Battery Interrupt Igniter N253 481_018 Battery28Fuses and RelaysVoltage distributor in plenum chamber The coolant fan control modules are supplied power via fuses located at this point. The main battery cable junction point is here. Fuse and relay carrier on the right side of the instrument panel The fuses are labeled SC in the current flow diagram. They can be accessed by the customer after removing the instrument panel end cover. Fuse and relay carrier and CAN node connector in luggage compartment, right Main fuse carrier at battery positive terminalThe battery interrupt The fuses are labeled SF in igniter is also mounted the current flow diagram. on this fuse carrier. The fuses can be accessed by the customer after removing the storage compartment on the right side.A6_Electrical_SystemFuse and relay carrier in the E-box in the plenum chamber, driver side (under the windshield washer system reservoir) The E-box lid also serves as a support for the engine control module. The fuses in the E-box are labelled SA in the current flow diagram.Coupling station and CAN node connector at the bottom left A-pillarFuse and relay carrier in the Vehicle Electrical System Control Module area (below the instrument panel in the driver footwell) The fuses are labeled SD in the current flow diagram.Fuse and relay carrier on the instrument panel, left The fuses are labeled SB in the current flow diagram. They can be accessed by the customer after removing the instrument panel end cover.29Control Module LocationsSome of the control modules shown in this overview are optional and/or are country-specific equipment. Boxes without numbers in the illustration indicate locations for components not used in the North American market. The color of a box indicates which data bus it communicates on. Refer to current technical literature for exact installation locations of control modules, as well as for installation and removal instructions.J387J428R161J851 J521J844 J500 J217 J852 R212 J285 J898 J623 J104 J850 J519 J745J794 J234 J255 J849J136G85 J527 J853J386Key: J136 J386 J387 J393 J519 J521 J605 J872 J873 Control Modules on the Convenience CAN bus Memory Seat/Steering Column Adjustment CM Driver Door Control Module Front Passenger Door Control Module Comfort System Central Control Module Vehicle Electrical System Control Module Front Passenger Memory Seat Control Module Rear Lid Control Module Front Passenger Multicontour Seat CM Driver Multicontour Seat Control Module E265 J255 J285 J527 J772 J791 J898 Control Modules on the Display and Control CAN bus Rear A/C Display Control Head Climatronic Control Module Instrument Cluster Control Module Steering Column Electronics Control Module Rear View Camera System Control Module Parallel Parking Assistance Control Module Windshield Projection Head-Up Display CM Control Modules on the Powertrain CAN bus Steering Angle Sensor Airbag Control Module Electromechanical Parking Brake Control Module Engine Control Module Transmission Control ModuleG85 J234 J540 J623 J21730J855 J197 J605 J393 J791 J540 J772 J769J872J492 E265 J533J873J770J525 J854Radio R481_009J745 J769 J844 J852 J853 J854 J855Control Modules on the Extended CAN bus Cornering Lamp and Headlamp Range CM Lane Change Assistance Control Module Automatic High Beam Assist Control Module Camera Control Module Night Vision System Control Module Left Front Seat Belt Tensioner Control Module Right Front Seat Belt Tensioner Control Module Control Modules on the MOST bus Instrument Cluster Control Module Digital Sound System Control Module Information Electronics Control Module 1 Radio DVD ChangerJ104 J197 J428 J492 J500 J849 J850 J851Control Modules on the FlexRay bus ABS Control Module Level Control System Control Module Distance Regulation Control Module All Wheel Drive Control Module Power Steering Control Module Sensor Electronics Control Module Distance Regulation Control Module 2 Image Processing Control Module Sub-Bus Users Infrared Camera Lane Change Assistance Control Module 2 Users of all Bus Systems (Gateway) Data Bus On Board Diagnostic Interface31J285 J525 J794 R R161R212 J770J533TopologyThis diagram shows the network topology for a vehicle with an extensive level of optional equipment.Right Front Seat Ventilation Control Module J799 Left Front Seat Ventilation Control Module J800 A/C Pressure/ Temperature Sensor G395 Garage Door Opener Control Module J530Wiper Motor Control Module J400 Rain/Light Recognition Sensor G397Humidity Sensor in Fresh Air Intake Duct G657Air Quality Sensor G238Power Output Module for Left LED Headlight Power Output Module for Right LED HeadlightMultifunction Steering Wheel Control Module J453Light Switch E1Power Adjustable Steering Column Control Module J866 Garage Door Opener Control Head E284 Anti-Theft Alarm System Sensor G578Vehicle Electrical System Control Module J519 Memory Seat/ Steering Column Adjustment Control Module J136 Front Passenger Memory Seat Control Module J521 Flap Control Servo Motors 1-16 Fresh Air Blower Control Module J126Power Sunroof Control Module J245 Rear Spoiler Control Module J223 Roof Electronics Control Module J528 Roof Shade Control Module J394Humidity Sensor G355Rear Lid Control Module J605 Alarm Horn H12 Comfort System Central Control Module J393Passenger Occupant Detection System Control Module J706 Selector Lever Sensor System Control Module J587Electronic Steering Column Lock Control Module J764 Anti-Theft Immobilizer Reader Coil D2Left Rear Door Control Module J388 Right Rear Door Control Module J389Driver Door Control Module J386 Front Passenger Door Control Module J387 Driver MultiContour Seat Control Module J873 Front Passenger Multi-Contour Seat Control Module J872Powertrain CAN Convenience CAN Extended CAN Display and Control CAN FlexRay Diagnosis CAN MOST bus LIN bus Sub bus system32Windshield Projection Head Up Display Control Module J898 Steering Column Electronics Control Module J527 Rear Left Vent Servo MotorsRear View Camera System Control Module J772 Parallel Parking Assistance Control Module J791 Climatronic Control Module J255Rear A/C Display Control Head E265 Instrument Cluster Control Module J285 Radio RDVD Changer R161Digital Sound System Control Module J525Information Electronics Control Module 1 J794MMI Display J685Data Bus On Board Diagnostic Interface J533 Battery Monitoring Control Module J367Airbag Control Module J234All Wheel Drive Control Module J492 ABS Control Module J104 Automatic High Beam Assist Control Module J844 Camera Control Module J852 Left Front Seat Belt Tensioner Control Module J854 Right Front Seat Belt Tensioner Control Module J855 Lane Change Assistance Control Module J769 Lane Change Assistance Control Module 2 J770Transmission Control Module J217Alternator CEngine Control Module J623Sensor Electronics Control Module J849 Distance Regulation Control Module J428Steering Angle Sensor G85Cornering Lamp and Headlamp Range Control Module J745 Left Headlamp Power Output Stage J667 Right Headlamp Power Output Stage J668Electromechanical Parking Brake Control Module J540Distance Regulation Control Module 2 J850 Image Processing Control Module J851 Level Control System Control Module J197Night Vision System Control Module J853Infrared Camera R212 481_001Power Steering Control Module J50033Exterior LightingLight Switch Summary Information Description Installation Location Functions Light Switch E1 Driver’s side, instrument panel Communicates the driver’s lighting setting request to the electrical system control module None, LIN slave, measured values, and diagnosis through Vehicle Electrical System Control Module J519 (master)Address Word486_048Function The rotary knob has four settings: 0 Lights OFF (in some countries, daytime running lights are switched ON automatically at “terminal 15 on”) Connections: Pin 1 Pin 2 Pin 3 Pin 4Light Switch E1486_094AUTO Automatic daytime running lights are switched ON and OFF depending on the light sensor Side light Low beamLIN to J519 “terminal 30” “terminal 31” Redundancy line to J519486_09534Button Functions The switch cluster on the left side of the light switch contains a maximum of three buttons: – Using the upper button, either the fog lights (vehicles with halogen lights) or the allweather lights (vehicles with bi-xenon or LED headlights) are activated – Using the center button, the Night Vision Assist can be activated – The bottom button is used to switch the rear fog light ON Due to different equipment levels and countryspecific regulations, the switch clusters differ and not all the buttons are active. Only the button for the rear fog light is used in all 2012 A6 models. Light Switch Symbols Fog lights (only for vehicles with Halogen headlights) All weather light (only for vehicles with Bi-xenon or LED headlights, not for North American market) Rotary Switch A maximum of two rotary switches are located on the right side of the light switch: – E376 Position Control for Head-Up Display (optional) – E20 Instrument Panel and Switch Illumination Dimmer Switch (always installed)486_094 E736 486_096Night Vision Assist Rear fog lightE2035HeadlightsThree headlight variants are offered in the 2012 A6: – Halogen headlights – Bi-xenon headlights – LED headlights The bi-xenon headlights are offered in the following versions: – Bi-xenon – Bi-xenon with adaptive light (AFS)Halogen HeadlightsDRL or high beam Parking light Turn signal Low beam Side marker light486_026_027Light Function Parking light Daytime running light (DRL) Turn signal Low beam headlight High beam headlight Fog light (in bumper, not shown) Coming home / leaving home Side market lightsBulb Used W5W H15 3457A-58 H7 H15 H7 H7 and H15 3 LEDsPower Output 5 watts 15 watts 30 watts 55 watts 55 watts 55 watts 55 and 15 watts approx. 2 wattsOn vehicles with halogen headlights, the fog lights are built into the bumper. This precludes equipping these vehicles with Adaptive Cruise Control (ACC) because the space for the ACC sensors is occupied by the fog lights.For the coming home/leaving home function, daytime running lights and fog lights are activated on vehicles with halogen headlights.36Halogen Headlight Components Headlight components such as caps, repair tabs, screws, and ventilation components can be replaced for all headlight variants on the 2012 A6. The individual components shown here can be replaced.Parking light M1 DRL L174 High beam M30 Low beam M29Turn signal light M5486_03137H15 Halogen Bulb The halogen headlight uses an H15 bulb for the daytime running lights and high beam functions. It is a dual-filament bulb with a 15-watt filament for DRLs, and a 55-watt filament for high beams. Three contact tabs project from the base of the H15 bulb. They serve to make the electrical contact but also act as a mechanical stop when the bulb is turned to tighten when installing.ReflectorH15 halogen bulb486_054ConnectorsBulb socket with connectorsA quarter turn clockwise is sufficient to tighten the H15 bulb and complete the electrical contact. Clamps or bails are not required with the H15 bulb.The H15 bulb can be installed in a single motion. This facilitates handling in the restricted space of the headlight housing.90° turn486_05538Bi-Xenon HeadlightsLow beam and high beam Turn signal Side marker light (LED)486_028_029 DRL or parking lightLight Function Parking light Daytime running light (DRL) Turn signal Low beam headlight High beam headlight Coming home / leaving home Side marker lightBulb Used 2x3 LEDs dimmed (via 2 optical fibers) 2x3 LEDs (via 2 optical fibers) PSY24W D3S D3S 2x2 LEDs and gas discharge lamp D35 3 LEDsPower Output not specified not specified not specified 24 watts 35 watts not specified approx. 2 wattsNeither the all-weather light function or fog lights are offered on vehicles with bi-xenon headlights in the North American market. The space for the ACC sensors is vacant on these vehicles, so it is possible to equip them with Adaptive Cruise Control (ACC). The coming home/leaving home function uses the parking lights in conjunction with the low beams. Switching from Low Beams to High Beams In the bi-xenon headlight, switching between low beams and high beams is done by a solenoid operated shutter. In its normal position the shutter is raised for the asymmetrical low beams. The solenoid is energized for the high beam function, which lowers the shutter, producing the bi-xenon lamp’s symmetrical light.Shutter for low beamsGas discharge lamp D35Shutter solenoid486_06639Bi-Xenon Headlight Components The individual components shown here can be replaced on a bi-xenon headlight.Left Daytime Running Lamp and Parking Lamp Control Module J860The LEDs and the optical fibers for the parking light/daytime running light functions are not replaceable.Left Headlamp Beam Adjustment Motor V48 Gas Discharge Lamp L13Turn Signal M5Left HID Headlamp Control Module J343Actuation Actuation of the individual lights and of the control module for DRLs and Parking lights is performed separately by Vehicle Electrical System Control Module J519.486_032Actuation of headlight range control is performed separately by Headlamp Range Control Module J431.Operational SchematicConvenience CAN Vehicle Electrical System Control Module J519 Discrete wiresBi-Xenon headlight (one side of vehicle) – Control Module for DRL and parking light – H7 bulb – 24 watt bulb – J343Headlamp Range Control Module J431 Extended CANDiscrete wireAdjustment Motor for Headlamp Distance Regulation 486_09940Bi-Xenon Headlights with AFSCornering light (static) Turn signal Low beam and high beam Side marker light486_114_115 DRL or parking lightLight Function Parking light Daytime running light (DRL) Turn signal Country light / highway light Low beam headlight Cornering light (static) Coming home / leaving home Side marker lightBulb Used 2x3 LEDs dimmed (via 2 optical fibers) 2x3 LEDs dimmed (via 2 optical fibers) PSY24W D3S D3S H7 2x2 LEDs and gas discharge lamp D35 3 LEDsPower Output not specified not specified 24 watts 35 watts 35 watts 55 watts not specified approx. 2 wattsThe all-weather light function is not offered on North American market vehicles with bi-xenon headlights and AFS. The installation space for the ACC sensors is vacant so Adaptive Cruise Control (ACC) is available.The parking lights are used for the coming home/leaving home function in conjunction with the low beams.Reference For further information about the head and tail lights of the 2012 A6, refer to Self-Study Program 990403, The 2012 Audi A7 Onboard Power Supply and Networking.41Bi-Xenon Headlight with AFS ComponentsLeft Headlamp Beam Adjustment Motor V48 Cornering Light M51 (static) Gas Discharge Lamp L13Left Daytime Running Lamp and Parking Lamp Control Module J860Turn Signal M5Left Headlamp Power Output Stage J667Left HID Headlamp Control Module J343Actuation Vehicle Electrical System Control Module J519 actuates the control module for the DRLs and parking lights, the control module for the gasdischarge lamp, the H7 bulb, and the 24-watt bulb separately.486_033Cornering Lamp and Headlamp Range Control Module J745 actuates the power module for headlights over a private CAN. Left Headlamp Power Output Stage J667 actuates the adjusting motor for the roller, the servo motor for headlight range control and the servo motor for the dynamic cornering light.Bi-Xenon headlights with AFS (one side of vehicle) – Control module for DRLs and parking lights – H7 bulb – 24 watt bulb – Control module for gas discharge lampOperational SchematicConvenience CANVehicle Electrical System Control Module J519Discrete wiresCornering Lamp and Headlamp Range Control Module J745 Extended CANPrivate bus (sub-bus)Power module for headlightsDiscrete wires– Roller adjustment motor – Headlight range control servomotor – Cornering lamp servomotor 486_100 42LED Headlights The LED headlights of the A6 feature LEDs for lighting functions. Each headlamp has a total of 57 LEDs together with accompanying heat sinks. A fan integrated into the headlight prevents the electronic components from overheating.High beamReflectors or projection modules are used, depending on the lighting function. Thick-walled optics are employed for the DRLs, parking lights, and turn signals to achieve a homogenous appearance for these lighting functions.Low beam (asymmetrical) Side marker light486_030_049 Low beam (symmetrical) Cornering light (static)Light Function Parking light Daytime running light (DRL) Turn signal Low beam headlight High beam headlight Cornering light (static) Coming home / leaving home Side marker lightLEDs Used LEDs (white, dimmed) LEDs (white) 2x2 LEDs 14 LEDs (5x2 chip and 4 single LEDs) 12 LEDs (3x4 chip, in addition to low beams) 4 LEDs (1x4 chip, in addition to low beams) 14 LEDs (5x2 chip and 4 single LEDs) 3 LEDs (white with yellow reflector)433 reflectors for high beams9 projection modules for low beamsThick wall optics for DRLs, parking lights, and turn signalsReflector for static cornering light 486_103DRLs / Parking Lights The DRLs and parking lights consist of 24 white LEDs. They are activated by a pulse-width modulated signal (PWM). The LEDs are operated in a dimmed state for the parking light function.Turn Signals The turn signal is comprised of 24 yellow LEDs. During turn signal operation, the LEDs for the DRLs are dimmed to the level of the parking light.486_104486_105Low Beam Headlights Nine projection modules with a total of 14 LEDs are used for the low beams. The LEDs for the DRLs are dimmed to the level of the parking light.High Beam Headlights Three quadruple chips are activated for the high beam function in addition to the LEDs for the low beams and parking lights.1x1 1x2 1x2 1x2 1x2 1x1 1x1 1x1 1x11x4 1x21x4 1x2 1x2 1x2 1x21x4 1x11x1 1x1 1x1486_106486_10744Cornering Light (static) A quadruple chip below the parking light is activated in addition to the low beam function for the static cornering light. These LEDs are provided with a reflector which illuminates the area to the side of the vehicle when turning. This light is activated either by the turn signal and a speed below 25 mph (40 km/h), or a wide steering angle at a speeds below 44 mph (70 km/h).Coming Home / Leaving Home The same LEDs that create the low beam are used for the coming home/leaving home lighting functions. These functions are activated either when exiting the vehicle by opening the driver’s door, or when unlocking the vehicle with the radio remote key. Light Switch E1 must be in the “AUTO” position, Rain/Light Recognition Sensor G397 must recognize darkness, and both functions must be enabled in the MMI.1x1 1x2 1x2 1x2 1x2 1x2 1x1 1x1 1x1 1x2 1x2 1x2 1x2 1x2 1x11x1 1x1 1x11x4486_109486_10645LED Headlight Components The individual components shown here can be replaced separately in the LED headlight.Left LED Headlamp Power Output Module 2 A32 (parking/DRL, turn signal)LED groups or individual LEDs cannot be replaced in the LED headlight.Left LED Headlamp Power Output Module 4 A34Left LED Headlamp Power Output Module 3 A33 (static cornering light)Left Headlight Fan V407 Left LED Headlamp Power Output Module 1 A31 (low beam, high beam)Left Headlamp Beam Adjustment Motor V48486_034Actuation Power modules 2 and 4 are energized over separate lines by Vehicle Electrical System Control Module J519. Power modules 1 and 3 are LIN slaves of J519.Operational SchematicDiscrete wires Convenience CAN Vehicle Electrical System Control Module J519Power module 1 A31 controls the fan in the LED headlight over separate lines. The fan is activated with “terminal 15 on” and runs permanently until terminal 15 is switched OFF.LED headlight (one side of vehicle) – Left LED Headlamp Power Output Module 2 A32 – Left LED Headlamp Power Output Module 4 A34Discrete wiresLIN bus– Left LED Headlamp Power Output Module 3 A33 – Left LED Headlamp Power Output Module 1 A31 Adjustment Motor for Headlight RangeLeft Headlight Fan 486_113Extended CANHeadlamp Range Control Module J431Discrete wires!46Note When replacing components of the LED headlights, always use VAS 6613 to prevent ESD.Rear LightsLED Rear Lights Almost all rear light functions utilize LED technology. The only exceptions are the back-up lights, which use a 16-watt bulb, and the rear fog light, which uses a 21-watt halogen bulb.Back-up light (W16W) Rear fog light (H21W)Turn signalBrake lightBrake light 486_124 Reflector Tail lights Reflector47Rear Lights at NightTail Light The LEDs also have an optical fiber to reinforce the impression of a continuous band of lights from all angles.486_117Brake Light (combined with tail light) The brake light is comprised of 45 LEDs.Turn Signal (combined with tail light) The turn signal is comprised of 45 LEDs that are also employed for the brake light function.486_119486_12148Fog Light with Tail and Brake Light This configuration ensures that the two lighting functions can be clearly differentiated. It also maintains the legally mandated minimum distance between the brake light and the fog light.486_123Light Functions not Illustrated Backup Light A 16-watt bulb is used for the backup light. The backup light function operates only in the quarter panel light. High Mounted Brake Light The 2012 A6 has a center high-mounted brake light at the upper edge of the rear window. This light supplements the brake light function comprised of 18 LEDsLight Function Tail light Brake light Turn signal Rear fog light Backup light High mounted brake light Side marker lightType 30x LED 45x LED 45x LED 1x H21W, 21 Watt 1x W16W, 16 Watt 18x LED 2x LED49Climate ControlOverviewClimate Control System Versions Three-zone and four-zone climate control systems are available on the 2012 A6. On the three-zone system, rear passengers can adjust the temperature via a button located on the rear center console. Two humidity sensors, Humidity Sensor in Fresh Air Intake Duct J657 and Humidity Sensor G355 are used in both the three- and four-zone systems. The four-zone system also has Rear A/C Display Control Head E265 with the following functions: – Temperature adjustment – Fan adjustment – Separate rear left and right air distribution adjustment To provide climate control in the rear, the fourzone system has air outlets in the B-pillars. The four-zone climate control system has the following features: – Automatic recirculation control by Air Quality Sensor G238 – Residual heat function – Separate footwell temperature control – Glove compartment cooling system – Three different air conditioning modes: soft, medium, and intensiveThree-Zone Climate Control SystemFour-Zone Climate Control SystemClimatronic Control Module J255Climatronic Control Module J255Rear upper body vent478_068Rear A/C Display Control Head E265478_069Reference For further information about the climate control systems of the 2012 A6, refer to Self-Study Program 990603, The 2012 Audi A7 Occupant Protection, Infotainment, Climate Control, and Head-Up Display.50InfotainmentIntroductionThe 2012 A6 comes equipped with the MMI Radio plus or the MMI Navigation plus system, depending on vehicle model level.MMI Radio plusMMI Navigation plus484_070484_065484_067484_069TopologyThe A6 Infotainment control modules communicate over the MOST bus. This allows very high data transfer rates. Picture signals from the back-up camera or DVD changer are transmitted as FBAS signals to Information Electronics Control Module 1 J794.Display and Control CAN busInstrument Cluster Control Module J285Radio RMOST bus DVD Changer R161 Digital Sound System Control Module J525Information Electronics Control Module 1 J794LINFront Information Display Control Head J685484_103Data Bus On Board Diagnostic Interface J53351Radio Media Center (RMC)The MMI Radio plus system belongs to the Radio Media Center infotainment platform. Depending on equipment level, the Radio Media Center combines nearly all the hardware functions of a modern infotainment system in a single housing, which is the equivalent of a 1-DIN device. The RMC is also central controller for the infotainment system. The main difference in the RMC with the third generation MMI system is that there is no separate radio control module. The functions of the radio are integrated into Information Electronics Control Module 1 J794. On vehicles with MMI Radio plus, J794 has an additional audio amplifier. Radio diagnosis with the VAS Scan Tool is done through Address Word 5F — Information Electronics Control Module 1 J794.Front panel of J794 for MMI Radio plus484_067RMC Control Modules This illustration below shows which control modules and functions are grouped within Information Electronics Control Module J749 of the Radio Media Center.Front Information Display Control Head Control Module J523 External Audi Source Connection (AMI) R199Radio control moduleCD Player R89Information Electronics Control Module 1 J794Digital Sound System Control Module J525 Speech Input Control Module J507SD card reader Telephone Transceiver R36 484_07352MMI Radio Plus (RMC)MMI Radio plus has the following features: – Two SD card readers – Integrated six-channel amplifier for the Audi Sound System with 180 watts power output – Bluetooth interface – Speech dialogue system – Driver Information System (DIS) with monochrome screen in the instrument cluster – Digital satellite radio – AUX in on center console – Compatible with optional equipment – 6.5-inch color display with 400 x 200 pixel resolution – Control panel with six freely assignable radio station keys – FM tuner with dual diversity With MMI Radio plus, the CD drive and the SD card reader support playback of the following audio files: – MP3 – WMA – AAC – WAV The metadata in these files (album, track, artist, etc.) and the embedded album cover can also be displayed. Bluetooth Interface The MMI Radio for the A6 comes with a Bluetooth interface, which enables the RMC to be used for the hands-free telephone and audio streaming. The Bluetooth HFP profile is used for the handsfree telephone and A2DP for audio streaming. The AVRCP profile is used to control the audio player connected via Bluetooth. The scope of the control options is dependent upon the device in use.SDARS AMI AM/FM1 FM2 Display 484_074 MOST bus 484_067Front panel of J794 for MMI Radio plusBack panel of J794 for MMI Radio plusSpeech Dialogue System MMI Radio plus comes with an integrated speech dialogue system, which can be used, among other things, for the hands-free telephone or for selecting a radio channel. The main functions of the RMC can be operated by voice control (for example, find a contact in a directory, dial a number, etc.).53MMI Navigation PlusThe MMI Navigation plus system is identical to the system of the 2011 A8. It is a third generation MMI system with the internal designation MMI3G plus. MMI Navigation plus features the following: – 60 GB hard drive (with approximately 20 GB for Jukebox) – 3D navigation with 3D city models – DVD drive – Two SD card readers (for SDHC cards up to 32 GB in size) – Premium speech dialogue system – Radio control module with phase diversity – Six-channel amplifier with 180 watts power output (integrated into the radio control module) – 8-inch TFT screen with 800 x 480 pixel resolution – Driver information system with 7-inch color screen in the instrument cluster – MMI touch – Bluetooth interface for: • Hands-free telephone (HFP) • Audio streaming (A2DP)Telephone MOST bus FBAS Display Navigation AMI 484_078 484_069Front panel of J794 for MMI Navigation plusBack panel of J794 for MMI Navigation plusThe A6 with MMI Navigation plus also includes the following standard equipment: – Audi Music Interface – Audi Connect (WLAN hotspot) – Digital satellite radio tuner54New Features of MMI Navigation Plus — Audi Connect Google Earth Map The 3D map display can be expanded to include satellite mapping via Google Earth. The 3D satellite map display is produced by combining the 3D map display with the existing 3D topographical display. This function is only available in combination with Audi Connect and an active data link. WLAN Hotspot The A6 has a WLAN hotspot in combination with Audi Connect. Passengers with suitable devices can use the WLAN hotspot to surf the Internet, retrieve data or e-mails or, for example, to conveniently and securely download the latest apps for an iPad. When a network link is active, it is indicated at the bottom right of the display. 2G is displayed for GSM network and 3G for UMTS network. The Universal Mobile Telecommunications System (UMTS) is a third generation (3G) mobile communications standard which provides for significantly higher data transfer rates (up to 7.2 Mbit/s with HSDPA [High Speed Downlink Packet Access] and up to 384 kbit/s without) than the second generation (2G) mobile communications standard, the GSM Standard (up to 220 kbit/s with EDGE and max. 55 kbit/s without).3D satellite map484_079Network connectivity displaySettingsUMTS receptionGSM reception484_081!Note The final operational features and graphic displays for Audi Connect and Google Earth may differ from those presented here. Always check appropriate literature for the latest information.55Google Earth MappingIf the Google Earth variant is active, the satellite maps are loaded directly from the Internet (currently from Google Earth). This satellite map is combined with the navigation map on the hard drive to produce a 3D satellite map. The prerequisites for use of Google Earth maps are: – MMI Navigation plus – Audi Connect – Data capable SIM card Loading Google Earth Maps The following requirements must be met in order to load mapping material from Google Earth: – T-Mobile SIM card inserted in the card reader – Active Audi Connect account – Configured data link Also, in the “Settings” menu of the navigation system: – Map type must be set to “Position 3D” – Map display must be set to “Google Earth” If these requirements are met, Information Electronics Control Module 1 J794 always loads the satellite map for the current location and the expected route. The loaded data packets are cached on the hard drive, where the current map view is then unpacked and displayed. If enough data packets are stored for a certain route because the user travels this route on a daily basis, a 3D satellite map can be displayed even without an active link to Google Earth. If there is not enough data in the cache to display a map of adequate quality on the MMI screen, the system informs the user and switches to the standard map.DestinationGoogle Earth home page Navigation CriteriaSettings Settings for Google Earth Navigation484_082CriteriaMap colors Orientation Map type Map display Map content Addit. info DestinationDay North Position 3D Google Earth off Settings484_0833D satellite map484_079This message is displayed if too little data is available Navigation Note Not enough Google Earth data in cache. Switching to standard map. OK CriteriaDestinationSettings484_084!56Note The final operational features and graphic displays for Audi Connect and