TECHNICAL DOCUMENTATION

SSP 990893 – The 2019 Audi Q3 Introduction

PDFEN77 pages15 MB
SSP 990893 – The 2019 Audi Q3 Introduction - PDF cover

This PDF is currently unavailable.

Read document text
The 2019 Audi Q3 IntroductioneSelf-Study Program 990893 Audi of America, LLC Service Training Created in the U.S.A. Created 03/2019 Course Number 990893©2019 Audi of America, LLCAll rights reserved. Information contained in this manual is based on the latest information available at the time of printing and is subject to the copyright and other intellectual property rights of Audi of America, LLC., its affiliated companies and its licensors. All rights are reserved to make changes at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise, nor may these materials be modified or reposted to other sites without the prior expressed written permission of the publisher. All requests for permission to copy and redistribute information should be referred to Audi of America, LLC.Always check Technical Bulletins and the latest electronic service repair literature for information that may supersede any information included in this booklet.Release Date: May 10, 2019The eSelf-Study Program (eSSP) teaches a basic understanding of the design and mode of operation of new models, new automotive components or new technologies. It is not a repair manual! Figures are given for explanatory purposes only and refer to the data valid at the time of preparation of the SSP. For further information about maintenance and repair work, always refer to the current technical literature.NoteReferenceii Introduction Dimensions13BodyOverview General body repairs 55 7Power unitFuel tank1011Power transmission8-speed automatic transmission 09P Functions influencing transmission control system1212 16Running gearOverview Axles Steering system Brake system Wheels and tires, tire pressure monitoring1818 19 21 23 25Electrics and electronicsPower supply Networking Exterior lighting Tail lights2727 29 31 34Convenience electronicsSteering Column Electronics Control Module J527 Interior lighting Digital instrument cluster 9SO Sensor-operated rear lid opening 3636 37 38 39Climate controlOverview4040Safety and driver assist systemsPassive safety System overview Active safety Driver assist systems 4343 45 47 48Infotainment and Audi connect Introduction and overview of versions  Button combinations for service Audi sound system  Antennas Audi connect Using the Audi connect services5555 58 61 65 69 70Inspection and maintenanceMY 2019 Audi Q3 Maintenance Intervals - USA7171AppendixeSelf-Study programs7272Knowledge assessment73iii Driver assist systemsIntroductionThe Audi Q3 is a family SUV with all-round talent. In the second generation, it is not only more self-confident in its appearance, but also much more useful thanks to the generous amount of space it has to offer, comprehensive variability and many practical details. Infotainment solutions from the luxury class network this compact SUV with its environment. New assist systems support the driver when parking, in town and when driving long distances. Compared with its predecessor, the new Audi Q3 has grown in virtually all dimensions. Its wheelbase, which has been stretched by 3.0 in (77.0 mm) makes the Q3 more spacious and at the same time, extremely versatile.Adaptive cruise control up to 124 mph (200 km/h). Peripheral view camera system for displaying 360° view of the surroundings and cross-traffic assist available.Engines At market launch, a 4-cylinder 2.0l TFSI engine delivering 228 hp will provide power to the quattro drive system via an 8-speed automatic transmission.Light LED headlights and taillights are standard on the new Audi Q3. LED lights illuminate the road at a high color temperature, while offering a low power consumption rate and long service life. The available Full LED headlights on Q3 Premium Plus and Prestige include a unique DRL signature. This lighting element can be seen in any time of day, providing an unmistakable presence on the road. Infotainment The Audi sound system is standard equipment while the Bang & Olufsen sound system with 3D sound is optionally available. MMI touch response with a high resolution touchscreen integrated into a black panel is now standard equipment.1 673_002Power transmission Power transmission to the wheels via an 8-speed automatic transmission and standard quattro all-wheel drive. The quattro system features an electro-hydraulically controlled drive coupling on the rear final drive.Body/interior Adjustable rear seat bench with variable backrest angle is standard. Variable luggage compartment floor; rear shelf can be stored under luggage compartment floor. Displays and operation The operating and display concept of the SUV has been overhauled from the ground up - Audi has done away with the analog instruments. Standard equipment includes a digital instrument cluster with a 10.25-inch screen which the driver operates using the multifunction steering wheel. With the top-of-the-line MMI navigation plus, the displays appear in the optional Audi virtual cockpit, which offers many additional functions.2 Dimensions63.62 in (1616 mm)144.44 in (1129 mm)62.36 in (1584 mm) 73.07 in (1856 mm)62.04 in (1576 mm) 79.68 in (2024 mm)673_003m)in (1041.4938.42in (976 mm )54 m29 44 in (748 mm)35.27 in (896 mm)105.51 in (2680 mm) 176.53 in (4484 mm)35.74 in (908 mm)673_0043 59.36 in (1508 mm)56.69 in (1440 mm)57.79 in (1468 mm)55.11 in (1400 mm)39.60 in (1006 mm) 37.99 in (965 mm)673_005Exterior dimensions and weights Length Width (not including mirrors) Width (including mirrors) Height Front track Rear track Wheelbase Unladen weight Maximum gross weight 176.53 in (4484 mm) 73.07 in (1856 mm) 79.68 in (2024 mm) 63.62 in (1616 mm)1 62.36 in (1584 mm) 62.04 in (1576 mm) 105.51 in (2680 mm) 3582.50 lb (1625 kg) 4894.25 lb (2220 kg)Interior dimensions and other specifications Front cabin width Front shoulder width Rear cabin width Rear shoulder width Load sill height 59.36 in (1508 mm)2 56.69 in (1440 mm)3 57.79 in (1468 mm)2 55.11 in (1400 mm)3 29.44 in (748 mm) 18.71 cu ft (530 l)4/ 53.85 cu ft (1525 l)5 0.318 CW 15.85 gal (60 l)Luggage compartment capacityDrag coefficient Capacity of fuel tankIncluding roof antenna Elbow room width 3 Shoulder room width 4 Seat bench in rearmost position, load up to top edge of backrest 5 With rear seat backrest folded down, load up to roof1 24 BodyOverviewThe 2019 Q3 is based on the MQB A2 matrix. It includes a frame structure of several ultra-high strength components formed by the tunnel, the upper and lower footwell cross members, side member (sill panel) and rear cross member. The ultra-high strength seat cross member provides additional support at the side. Die-quenched panels and ultra-high strength steel (hotformed) are also used for the body structure. Thanks to these die-quenched panels and particularly to the ultra-high strength hot-formed components, it was possible to increase the torsional rigidity of the Audi Q3 body.Key: Sheet aluminum Aluminum section Ultra-high-strength steel (hot-formed) Modern high-strength steel High-strength steel Soft steel5 Joining techniquesThe main joining method used for the construction of the Audi Q3 body is resistance spot welding. Resistance spot welding is combined with a high-strength bonding process in the areas of the vehicle body where stringent requirements for vibration comfort and passive safety apply. The following joining techniques are also used: ›› ›› ›› ›› ›› ›› ›› ›› MAG welding Laser welding for steel Laser soldering/brazing MIG soldering/brazing for steel Seaming Bonding Flow-drill screws Pop riveting673_0066 General body repairsRear lidAn electrically operated rear lid is standard equipment on the 2019 Audi Q3. The left and right spindle drives for the rear lid are identical. The installation brackets have a marking to ensure the spindle is installed in the correct position.Power latching systemThe rear lid also has a power latching system. When the rear lid is closed and the microswitch in the rear lid lock detects that the striker plate is in the initial catch, Rear Lid Closing Aid Motor V382 pulls the rotary latch in the rear lid lock further into the main catch via a Bowden cable.Brackets for electric rear lid673_008Damper weightA damper weight, designed to minimize any vibrations transmitted to the rear lid from the final drive components is installed on all models.Nut/boltRear Lid Closing Aid Motor V382 Damper weight673_010Rear spoilerThe main purpose of the roof spoiler on the rear of the Audi Q3 is aerodynamics. The spoiler reduces aerodynamic drag and in conjunction with the side dynamic trim, optimizes turbulence behind the vehicle. This in turn reduces dirt build-up on the rear window. The aerodynamic trim panels are located by clips that position them in the top section of the spoiler and are additionally secured by adhesive strips. The spoiler itself is retained with four bolts. The high-level brake light is installed in the spoiler. The spoiler may also house AM and FM antennas depending the infotainment equipment installed.7 Luggage compartmentThe size of the luggage compartment is variable. Moving the rear bench seat forward up to 5.5 in (150 mm) and using the 7-level seat back angle adjustment allows the luggage compartment volume to be adjusted as required. The seat backrest is split in a 40:20:40 configuration. To increase the variation options even more, there are three positions for the height of the luggage compartment floor. This is accomplished by unique supports on both sides of the luggage compartment side trim panels. There are also supports on the same level at the rear in the lock carrier trim. In the lowest position, the luggage compartment floor sits on the luggage compartment floor lining. To lower the luggage compartment floor, it must be lifted by the handle at the rear, pulled back slightly and pushed back into the desired position at the front. The rear shelf can also be stored under the luggage compartment floor when it is not needed.673_0118 Instrument panelThe instrument panel has a two-part horizontal design. The horizontally arranged air outlets are integrated in the upper section. The large central trim section is installed underneath. It surrounds the MMI touch display. Two decorative trim panels on the passenger side underline the horizontal layout. The lower one ensures that no securing elements are visible to the occupant. Because it is constructed in layers. It may be necessary to remove more parts than initially expected to remove a component. Always follow the procedures described in ElsaPro.Instrument panelAir vent (center)Air vent (passenger side)MMI touch display panelInstrument cluster insert trimTrim (center)673_012Air vent (driver side)Trim (top, driver side)Decorative trim (passenger side)Trim (top, Trim (bottom, passenger side) passenger side)Decorative trim with light switch module9 Power unitEngine with code DHHAPower in kW Torque in Nm01000200030004000500060007000673_023Engine speed [rpm]673_022Features Engine code Type Capacity Stroke Bore Number of valves per cylinder Firing order Compression ratio Power output Torque Turbocharging Engine management Maximum injection pressure in bar Emission control Emission standardTechnical data DHHA Four-cylinder in-line engine 121 cu in (1984 cc) 3.65 in (92.80 mm) 3.24 in (82.50 mm) 4 1–3–4–2 9.60 228 @ 5,000 - 6,700 rpm (170 kW @ 5,000 - 6,700 rpm) 258 @ 1700 - 4400 rpm (350 Nm @ 1700 - 4400 rpm) Turbocharger Continental Simos 18.1 3525.9 psi (250 bar) Regulated cat. conv. LEV III/Tier 3 3010 Fuel tankA molded two chamber saddle tank with a capacity of 15.8 gal (60 l) is used on the 2019 Audi Q3. When the vehicle is being driven, fuel is initially pumped into the main chamber by the suction-jet pump in the side chamber of the fuel tank, and from there to the engine. Fuel is pumped from the main chamber to the side chamber through the drive line (small diameter, high speed). This creates the Venturi effect and the fuel is conveyed from the side chamber to the main chamber via the aggregate jet line (large diameter, lower speed).Suction-jet pumpBreather lineDrive line673_025Main chamberAggregate jet lineReservoir with integrated fuel filter in delivery module (lifetime)Filler neckSide chamber11 Power transmission8-speed automatic transmission 09PThe 8-speed automatic transmission 09P has the internal factory designation AQ450 8A. It is a further development of the 09G 6-speed automatic transmission. (The 09G transmission was not used in the North American Region.). It has been developed and manufactured by the Japanese company AISIN AW CO., LTD.Multifunction Transmission Range Switch F125 Transmission Control Module J217 Connector A Connector B673_035Connector CSelector mechanism, refer to function diagram on page 14Transmission Control Module J217 is located in the right front fender behind the wheel housing liner. Multifunction Transmission Range Switch F125 is actuated by the selector lever cable and informs J217 of the gears selected.The transmission planetary gear sets provide the eight speeds. These are selected by four multi-plate clutches, a brake band (B1), a multi-plate brake (B2) and a freewheel. The 09P transmission is equipped with Transmission Fluid Auxiliary Hydraulic Pump 1 V475. This among other things, allows the vehicle to support the stop/start function.Shift matrix: 09G transmissionValve Shift element 1st gear 2nd gear 3rd gear 4th gear 5th gear 6th gear 7th gear 8th gear Reverse gear N217 Clutch 1 N218 Clutch 2 --------N233 Clutch 3 ----N371 Clutch 4 ------N216 Brake 1 --N88 Brake 2 Freewheel° ° ° ° °---------*---------------°-----------------°-----------°-------°---° ° ° °---°-------°---°---°°° used --- not used * in tiptronic mode, brake 2 locks the freewheel, engine braking can be used12 Function diagramKey: Output Input Actuator wire Sensor wire Discrete wire Positive wire Ground wireF41 F125 G93 G182 G195 J217 J587 N88 N89 N110 N215 N216 N217 N218 N233 N371 N510 V475 Y26 Back-Up Switch switch Multifunction Transmission Range Switch Transmission Fluid Temperature Sensor Transmission Input Speed Sensor Transmission Output Speed Sensor Transmission Control Module Selector Lever Sensor System Control Module Solenoid Valve 1 Solenoid Valve 2 Shift Lock Solenoid Automatic Transmission Pressure Regulating Valve 1 Automatic Transmission Pressure Regulating Valve 2 Automatic Transmission Pressure Regulating Valve 3 Automatic Transmission Pressure Regulating Valve 4 Automatic Transmission Pressure Regulating Valve 5 Automatic Transmission Pressure Regulating Valve 6 Automatic Transmission Pressure Regulating Valve 8 Transmission Fluid Auxiliary Hydraulic Pump 1 Selector Lever Transmission Range Position Display UnitActivation of Y26, frequency modulated signal to J587 Tip+, Tip-, frequency modulated signal from J587 Plus activation of N110 to J587 CAN bus Low (powertrain) CAN bus High (powertrain) Term. 30Term. 15P/N signal to approve engine start673_036Shift matrix: Multifunction Transmission Range Switch F125Shift between D/SThe shift matrix of the multifunction switch indicates which contacts are connected in the corresponding gear.673_03713 Function diagram - selector mechanismThe 09P transmission is equipped with a multi-function switch that reports the selected gears to Transmission Control Module J217. Because of this, the selector mechanism functions are restricted to the P signal, the PWM signal for Tip + and Tip - and the detection of tiptronic mode. Selector Lever Transmission Range Position Display Unit Y26 is activated with a frequency modulated signal transmitted via a discrete wire from Transmission Control Module J217. All functions and connections of the selector mechanism are checked and diagnosed by the TCM.E313 Selector Lever has the following components: F319 Selector Lever Park Position Lock Switch J587 Selector Lever Sensor System Control Module G727 Selector Lever Position Sensor N110 Shift Lock Solenoid The complete unit must be replaced if one of these components is defective. Y26 Selector Lever Transmission Range Position Display Unit N376 Ignition Switch Key Lock Solenoid J217 Transmission Control Module673_038Term. 31 P signal to N376 Activation of Y26, pulse-width modulated signal from J217Term. 30 Term. 15Plus activation of N110 from J217 Term. 58d Tip+, Tip-, pulse-width modulated signal to J217Key: Output Input Actuator wire Discrete wire Positive wire Ground wire14 Parking lock manual releaseIn the event the selector lever lock malfunctions, Shift Lock Solenoid N110 malfunctions or the vehicle voltage is too low, the parking lock can be released manually after removing the shift lever boot. There is an opening next to the selector lever through which the yellow manual release mechanism can be seen.Selector leverManual release mechanismShift Lock Solenoid N110Release leverRelease pin Locking pin engaging in locking gate of inner housing Selector lever Connector BConnector AManual release mechanismReturn lever674_031Articulation point of parking lock cable Release lever Ramp If the manual release mechanism is pressed downwards, the release lever slides along the ramp in the selector mechanism housing and presses the locking pin out of the locking gate using the release pin. This cancels the selector lever lock. The parking lock can be released. Parking lock cableNote Before the manual release mechanism for the parking lock is operated, the vehicle must be secured to prevent it from rolling away.15 Functions influencing transmission control systemAudi drive selectAs is other Audi models, different driving modes can be selected via the Audi drive select button or through the MMI. When the ignition is switched on, the vehicle is always restarted in the most recently selected drive mode and in transmission position D. The only exception to this is when offroad mode is selected.drive select button673_039offroad In offroad mode, the transmission control system assists driving in rough terrain by using adapted functions. D is shown as the transmission position. Gear selection follows a fixed shift program. The gears are shifted late. Transmission position S is not available, but manual shifting is possible in tiptronic mode (manual mode M). Automatic upshifting of the transmission is deactivated in tiptronic mode. The engine revs up to the rpm limit without shifting up. This prevents unwanted continuous up-and-down shifting. The deactivation of automatic upshifting allows the engine to stop on a hill at maximum revs. Even if traction is lost briefly, the gear is held to ensure that the full drive torque is available when the wheels regain full traction. The deactivation of automatic upshifting allows the full braking effect of the engine to be utilized when driving downhill. To protect the engine against over-revving, the transmission shifts up before a defined engine speed is reached. If the ignition is switched off and then on again, the vehicle is restarted in auto mode and in transmission position D.auto Transmission position D: Shift point selection is performed with an emphasis on comfort. Transmission position S: In transmission position S, the system is in sport mode. Shift points are selected with an emphasis on a sporty driving style; they are adapted to the engine power range. The shift times are short and result in perceptible shifts.dynamic If dynamic mode is selected, Transmission Control Module J217 activates the sport program (transmission position S). In dynamic mode, it is possible to shift to D at any time. individual In individual mode, the driver can freely select the setup irrespective of other vehicle systems. The menu item Drive system covers the engine, transmission and start/stop system. Via this menu item, the options balanced or dynamic can be selected. These options correspond to the Audi drive select modes as follows: ›› Balanced corresponds to the Audi drive select mode auto ›› Dynamic corresponds to the Audi drive select mode dynamiccomfort The transmission control system operates in a similar way to auto mode.16 Start/stop systemThe start/stop system can help to save fuel and therefore reduce CO2 emissions. To achieve this, the system switches the engine off automatically when the vehicle comes to a halt for example, at traffic lights. As soon as the engine has been switched off by the start/stop system, the start/stop operation indicator lamp appears in the instrument cluster. The transmission positions P, N or D must be selected so that the start/stop function can be performed. If all requirements2 for start/stop operation are fulfilled, the engine is switched off when the brakes are applied with sufficient pressure and the vehicle’s speed drops below 4 mph (7 km/h)1. If the driver takes his foot off the brake pedal before the vehicle comes to a stop, the engine is restarted and the indicator lamp goes off. If the driver keeps his foot on the brake pedal, the engine remains switched off until the vehicle comes to a stop and is only switched back on when the brake pedal is released.673_040Special features of the steering wheel tiptronic functionThe “tiptronic in D/S” function with which manual shifts can be performed at any time is available. The D/S symbol lights up Selector Lever Transmission Range Position Display Unit Y26 and the gear indicator M 1 - 8 appears in the instrument cluster. If the vehicle remains in a normal, constant driving state for a period of about 8 seconds1, the transmission shifts back into position D or S. The countdown of approximately 8 seconds1 is stopped in the following cases: ›› ›› ›› ›› Sporty driving style Cornering Overrun Selection of another gear with the steering wheel tiptronicThe transmission can be immediately switched from manual mode M back to transmission position D or S by activating Tip+ for a period longer than  1 second1 (long pull +).Adaptive cruise controlAdaptive cruise control interacts with the automatic transmission by regulating the vehicle’s longitudinal movement. If regulation in the longitudinal direction is active, the vehicle’s speed is regulated and the distance to the vehicle in front may also be regulated. The vehicle can be brought to a halt and also set in motion again. Gearshifts are performed depending on the vehicle’s speed. The power flow to the engine is interrupted while the vehicle is stationary by opening the clutches.ServiceTowing the vehicle›› Maximum towing speed: 31 mph (50 km/h) ›› Maximum towing distance: 31 mi (50 km)Transmission warning/indicator lampsIf the red warning lamp appears in the instrument cluster, the driver is instructed not to drive any further.673_042 673_043If the yellow indicator lamp appears in the instrument cluster, it is generally possible to continue driving the vehicle. A corresponding driver message informs the driver of what to do.DiagnosisThe electric and electronic components of the automatic transmission can be diagnosed using the VAS Scan Tool under Address Word 0002.1 2The stated values are approximate. They may vary depending on the vehicle version. Information about requirements for the start/stop system can be found in the Owner’s Manual.Reference For detailed and up-to-date information on the warning and indicator lamps, refer to the Owner's Manual.17 Running gearOverviewThe running gear for the 2019 Audi Q3 has been completely redesigned compared to the previous model. The basis for this was the modular transverse matrix (MQB). MacPherson struts are used at the front and multi-link suspension at the rear. The electro-mechanical parking brake and power steering are similar to other Audi models.Running gear versions Running gear with steel suspension and non-variable damping for North America (1JN)Features This running gear is used in vehicles for the North American market. Compared to the standard running gear, the ride height is 18.5 mm higher on the front axle and 13.5 mm higher on the rear axle.673_04418 AxlesFront axleA particular emphasis was placed on the lightweight construction. This is based on the MQB platform, which has already been the basis for developing other Group models. Two plastic covers secured to the wishbones from below with rivets help the vehicle to achieve its good drag coefficient.Shock absorber Hydraulic twin-tube gas struts with non-variable or controlled dampingSubframe Welded sheet steel constructionWheel bearing housing Cast aluminum componentWishbone Welded steel constructionAnti-roll bar Tubular anti-roll barsAnti-roll bar coupling Sheet steel stamped part with rolled ball joint673_045Wheel bearing/wheel hub Second generation wheel bearing19 Rear axleThe rear axle is based on the proven multi-link suspension design principle already used on the Audi A3. Its basis is the MQB platform. Running gear alignment On the front axle, the toe settings for each wheel can be adjusted at the track rods. The camber values can be equalized by shifting the sub-frame. Toe and camber can be adjusted individually on the rear axle.Shock absorber Hydraulic twin-tube gas struts (non-variable and not controlled)Upper transverse link Track rod (not visible) Sheet steel constructionSubframe Welded steel constructionAnti-roll bar coupling Steel springs With linear spring characteristic, dual-coated surface Hub carrier Cast aluminum componentSubframe mounting Conventional bonded rubber mounting Trailing arm673_046Wheel hub/wheel bearingAnti-roll bar Tubular anti-roll barsSpring link High-strength steel constructionLower track rod (front) Sheet steel construction20 Steering systemThe electromechanical power steering system (EPS) used on the 2019 Q3 is similar to the previous model but has been revised as part of the modular strategy (MQB). However, the differences in terms of design, operation and servicing requirements are minimal*. The mechanically adjustable steering column (including steering lock) is similar to the previous model.Three-spoke leather steering wheelSteering column with mechanical adjustmentElectromechanical power steering system (EPS) with parallel axle drive673_048Reference*For further information on the design and functions of the EPS with parallel axle drive, refer to eSelf-Study Program 990243 The 2015 Audi Q3 Introduction.21 Steering wheelsTwo versions of steering wheels are available. Both have a diameter of 14.76 in (375 mm).Steering wheelEquipment levelStandard equipmentOptional steering wheel. Available with the Sport Interior package on Premium plus and Prestige models.22 Brake systemThe brake system for the 2019 Q3 in the North American Region is designed for a minimum wheel size of 17”. TRW C60 floating caliper brakes are used on the front axle; the rear axle uses the FNc-M42 system. The brake circuits are a diagonal split design. Brake pad wear indicators are standard equipment. The third generation electromechanical parking brake (EPB) is similar to that of the Audi A3.Brake systemEngine Minimum wheel size Type of brakes Number of pistons Brake disc diameter Brake disc thicknessFront axle2.0 ltr. TFSI 17" TRW C60 floating caliper brake 1 13.38 in (340 mm) 1.18 in (30 mm)Rear axle2.0 ltr. TFSI 17" Continental FNc-M42/12/11 - EPB floating caliper brake 1 12.20 in (310 mm) 0.86 in (22 mm)673_049673_050Reference For further information on the design and functions of the electromechanical parking brake (EPB), refer to eSelf-Study Program 960143, The 2015 Audi A3 Running Gear and Suspension System.23 Brake master cylinder and brake servo An 11-inch single servo brake booster is used on the 2019 Q3. The aluminum tandem master brake cylinder with a 1.0 in (25.4 mm) diameter provides the necessary performance with short brake pedal travel and a low pedal actuation force. A non-contact Hall sensor is used to actuate the brake lights.673_051ESC The 2019 Audi Q3 uses the MK100 ESC system. This is similar to the system of the Audi A3. In the North American Region, two versions are available. 1. Vehicles without adaptive cruise control. 2. Vehicles with adaptive cruise control. (Available only on Premium Plus and Prestige models). On vehicles with adaptive cruise control the vehicle speed is regulated until the vehicle is stationary. This requires specific adjustments to the software and hardware to ensure that the vehicle also brakes and regulates comfortably at speeds less than 18.6 mph (30 km/h). The ESC hydraulic units are equipped with larger pumps so that they can build up pressure more quickly. The Audi Q3 features active wheel speed sensors. The sensors on the rear axle can also detect the direction of rotation. The driver can also choose between ESC standard mode and offroad mode. Offroad mode is activated by briefly pressing the ESC button (less than three seconds). Regulating inputs are then only made at higher slip values. This allows for better traction in offroad conditions. Pressing the button for longer than three seconds switches off ESC regulation for the duration of the current ignition on cycle. The control module and the hydraulic unit can be separated in service; the control module can be replaced individually. As is already the case for other Audi models, this work must be performed at an ESD workplace to prevent electrostatic discharge. The ESC servicing requirements of the Audi Q3 are similar to those of the Audi A3.ESC unit673_052Reference For further information on the design and functions of the ESC, eSelf-Study Program 960143, The 2015 Audi A3 Running Gear and Suspension System.24 Wheels and tires, tire pressure monitoringThe 2019 Q3 is equipped with 18” wheels with 235/55 allseason tires as standard equipment. Q3 S line models come with 19” wheels with 235/50 all-season tires as standard with 20” wheels with 244/40 summer tires as optional. A space saving spare tire, tool kit and car jack are standard equipment.Q3Q3 S line18” 5-arm design wheels with 235/55 all-season tires19” 5-twin-spoke design wheels with 235/50 all-season tires20” 5-twin-spoke module design wheels with 255/40 summer tiresTire pressure monitoringThe 2019 Q3 uses the second generation tire pressure monitoring system. It functions based on information from the ABS Control Module. It is identical to the system used on the 2015 Audi A3 in terms of design, operation, driver information provided, service operations and diagnostics.25 26 Electrics and electronicsPower supplyBattery, jump-start terminals, fuse and relay carriersThe vehicle battery is located in the engine compartment and is protected by an insulating blanket. The North American Region version of the Q3 will be equipped with a 72 Ah/280A battery and a 140A alternator. The battery positive terminal and the ground stud near the left-hand strut tower are used for battery charging and jump starting. The fuses in the engine compartment electronics box (“SB”) and the fuses located behind the instrument panel on the left side of the vehicle (“SC”) are also accessible to the driver and are described in the Owner's Manual.Battery:E-box with fuses and relays, designation of the fuses in Wiring Diagram: “SB”Fuse holder and relay carrier under the instrument panel on the left, designation of the fuses in Wiring Diagram: “SC”.27 673_05328 NetworkingTopologyA27 J245 J605J745A31J926J386J927J387J428J126R242G805J255J844G238J769J345J770J764J938J518CJ367J533J623J492J500J587J928J104V475J446J234 J794 J854 J855J791Key:The topology shows all control modules which may be connected to the bus systems. Some control modules are the result of optional or country-specific equipment. Control modules marked “OR configuration” are never both installed in a vehicle; one of them (at most) may be installed, depending on the vehicle equipment. All CAN bus systems used in the Audi Q3 are high-speed CAN systems with a data transfer rate of 500 kbit/s. As on the Audi A3, the MOST 150 has replaced the MOST 25 on the Audi Q3.Powertrain CAN Running gear CAN Extended CAN Convenience CAN MIB CAN Infotainment CAN Diagnostics CANSub-bus systems LIN bus LVDS MOST bus Composite video OR configurationA27 Right LED Headlamp Power Output Module 1 A31 Left LED Headlamp Power Output Module 1 C Alternator E1 Light Switch E67 Driver Volume Control29 J525 J285J519J794E1J928G397 G355J400J685J772J530E67H12J1146G578Ambient light 1-nJ527J453673_054G238 G355 G397 G578 G805 H12 J104 J126 J234 J245 J255 J285 J345 J367 J386 J387 J400 J428 J446 J453 J492 J500 J518 J519 J525 J527 J530 Air Quality Sensor Humidity Sensor Rain/Light Recognition Sensor Anti-Theft Alarm System Sensor Refrigerant Circuit Pressure Sensor Alarm Horn ABS Control Module Fresh Air Blower Control Module Airbag Control Module Sunroof Control Module Climatronic Control Module Instrument Cluster Control Module Towing Recognition Control Module Battery Monitoring Control Module Driver Door Control Module Front Passenger Door Control Module Wiper Motor Control Module Adaptive Cruise Control Module Parking Aid Control Module Multifunction Steering Wheel Control Module All Wheel Drive Control Module Power Steering Control Module Access/Start Authorization Control Module Vehicle Electrical System Control Module Digital Sound System Control Module Steering Column Electronics Control Module Garage Door Opener Control ModuleJ533 J587 J605 J623 J685 J745 J764 J769 J770 J772 J791 J794 J844 J854 J855 J926 J927 J928 J938 J1146 R242 V475 Data Bus On Board Diagnostic Interface Selector Lever Sensor System Control Module Rear Lid Control Module Engine/Motor Control Module Front Information Display Control Head Cornering Lamp and Headlamp Range Control Module Electronic Steering Column Lock Control Module Lane Change Assistance Control Module Lane Change Assistance Control Module 2 Rearview Camera System Control Module Parallel Parking Assistance Control Module Information Electronics Control Module 1 Automatic High Beam Assist Control Module Left Front Seat Belt Tensioner Control Module Right Front Seat Belt Tensioner Control Module Driver Side Rear Door Control Module Passenger Side Rear Door Control Module Peripheral Camera Control Module Power Rear Lid Opening Control Module Mobile Device Charger 1 Driver Assistance Systems Front Camera Transmission Fluid Auxiliary Hydraulic Pump 130 Exterior lightingLight switchThe light switch (E1) of the 2019 Q3 has been modified and now is similar to the new light switch of the 2019 Audi A8. The new design means the switch also has a new operating concept.1 2 3Operating conceptAUTO is activated automatically when Terminal 15 is activated. Various lighting functions can be selected when button 1 is pressed. ›› AUTO - The lights adjust to their surroundings automatically. The daytime running lights, tail lights and license plate lights switch on permanently. ›› Low beam - The low beam headlights are switched on as soon as Terminal 15 is active. Button 2 can be used to activate the all-weather lights. Button 3 switches the rear fog light on and off (A rear fog light will not be offered in the North American Region.) The function selected is briefly displayed to the driver in the instrument cluster. ›› Side marker light - The side marker lights can be switched off at speeds below 6.2 mph (10 km/h). ›› OFF - All lighting functions can be switched off at speeds below 6.2 mph (10 km/h). If the vehicle exceeds a speed of 6.2 mph (10 km/h), AUTO is activated automatically.Light switch on Audi Q3673_056Electrical systemThe light switch is a LIN slave of Vehicle Electrical System Control Module J519 and requires only three wires: two for the power supply and the LIN wire to J519.Key:Vehicle Electrical System Control Module J519 Light Switch E1LIN bus Positive wire Ground wire673_05731 HeadlightsThere are two different headlight versions available for the 2019 Q3: ›› Basic headlights with LED technology (ECE1 and SAE2) ›› Full LED headlights (ECE1 and SAE2)Standard LED headlights (PR No.: 8EX + 8G0/8G1 + 8VA)A bulb is used for the turn signal in the basic headlight. All other lighting functions are produced by LEDs. The illustration shows the left headlight in the ECE1 version.Lighting functions: ›› ›› ›› ›› ›› Daytime running light (1) Marker light (1) Low beam (2) High beam (3) Turn signal (4) with PWY24W bulb ›› Side marker light (not illustrated, SAE only2)43 12673_058Special features of the lighting functions Turn signals during the day on SAE vehicles: The daytime running lights are switched off when the turn signals are activated.2Headlight range adjustment Vehicles with basic headlights have automatic static range adjustment. The vehicle level is calculated via a sensor on the rear axle. The headlight range control motors cannot be replaced. Activation/service The turn signal bulbs are activated directly by Vehicle Electrical System Control Module J519 and can be replaced if they fail. The LEDs for other functions are activated by Left and Right LED Headlamp Power Output Modules 1 and 2 - A27 and A31. The two output modules receive commands regarding the individual lighting functions and headlight range control from Cornering Lamp and Headlamp Range Control Module J745. J745 and modules A27 and A31 communicate using a Private CAN. The output modules can be replaced in the event of a fault. In the event of damage to the upper and inner headlight attachment points, repair tabs can be attached to the headlight housings.Turn signals at night: The marker lights remain on.Coming home/leaving home function When it is dark, the entry/exit lighting illuminates the area around the vehicle when the driver switches off the ignition, and opens the door. The entry/exit lighting only takes effect when it is dark and when the light switch is in the AUTO position. The function activates the low beam, the marker light and the tail light. On the SAE2 version, the side marker light is also activated.1 2ECE = for the European market SAE = for the North American market32 Full LED headlights (PR No.: 8IT + 8G0/8G1 + 8VM)All lighting functions are provided by LEDs on the Audi Q3 LED headlight. The illustration shows the left headlight in the ECE1 version. Lighting functions: ›› Daytime running light (1) ›› Marker light (1) ›› Turn signal (1) ›› Low beam (2) ›› High beam (3) ›› All-weather light (4) ›› Low beam (4), one-side ›› Intersection light (4) ›› Highway light (2), raised via headlight range control ›› Static cornering light (4), one-side ›› Maneuvering light (2 + 4), when reverse is selected ›› Side marker light (not illustrated, SAE only2)673_059432 1 11Special features of the lighting functions All lighting functions of the LED headlights are produced by LEDs. Turn signals during the day: The daytime running lights are switched off when the turn signals are activated. Turn signals at night: Transition turn signal = in the bright turn signal phase, the yellow LEDs are active; in the dark turn signal phase the white LEDs light up to marker light level. Maneuvering light: When reverse is selected, the low beams and the all-weather lights are activated. This is intended to make it easier for the driver to see potential obstacles. Coming home/leaving home function On vehicles with full LED headlights, the entry/exit lighting involves activating the low beam headlights and the marker lights. On the SAE2 version, the side marker lights are also switched on. When it is dark, the entry/exit lighting illuminates the area around the vehicle when the driver unlocks the vehicle and after the ignition has been switched off and the driver’s door has been opened. The entry/exit lighting only takes effect when it is dark and when the light switch is in the AUTO position.Headlight range adjustment The LED headlights are equipped with automatic dynamic headlight range adjustment. The vehicle level is calculated via a sensor on the rear axle. The headlight range control motors can be replaced.Activation/service The LEDs in the LED headlights are activated by the output modules A27 and A31. The two output modules receive commands regarding the individual lighting functions and the headlight range control from Cornering Lamp and Headlamp Range Control Module J745. Information is exchanged via a private CAN. The output modules installed on the outside of the headlight housings can be replaced in the event of a fault. It is not possible to replace individual lights. In the event of damage to the upper and inner headlight attachments, repair tabs can be attached to the headlight housings.1 2ECE = for the European market SAE = for the North American market33 Tail lightsLED tail lightsOn the LED tail lights, all lighting functions are performed by LEDs. The turn signal display is sequential. The illustration shows the left LED tail lights in the ECE1 version. Lighting functions: ›› Tail light (1) ›› Brake light (2) ›› Dynamic turn signal (3) ›› Back-up light (4) ›› Rear fog light (5) (Not offered in the NAR)Left Tail Lamp MX3 Left Tail Lamp 2 MX53 1 1 1 1 2345673_062Activation/special features All tail light functions are activated by Vehicle Electrical System Control Module J519. Because the LEDs in the tail lights generate less heat, the rear lid tail lights are not switched off when the rear lid is opened.Special features of SAE2 version The side marker light function for the SAE2 version is performed via the tail light present in the side light, meaning that no additional side marker light is required. Tail lights for the SAE2 version do not have a rear fog light.1 2ECE = for the European market SAE = for the North American market34 High-level brake lightThe high-level brake light is integrated into the rear spoiler and provides additional brake lighting via 18 LEDs. Its total power is 2.2 W. It is not possible to replace individual parts of the high-level brake light. It must be replaced as a complete unit in the event of a fault.673_063License plate lights The license plate lights on the Q3 also use LED technology and have two LEDs each. Like the high-level brake light, they are activated by Vehicle Electrical System Control Module J519. The license plate lights are retained by clips in the rear lid.673_064673_06535 Convenience electronicsSteering Column Electronics Control Module J527Unlike the first generation Q3, J527 does not participate in CAN data transfer. J527 communicates with Vehicle Electrical System Control Module J519 and Data Bus On Board Diagnostic Interface J533 via the LIN data bus. However, the tasks and functions of J527 have not changed.Turn signal switchSteering Column Electronics Control Module J527Electronic Steering Column Lock Control Module J764Switch for cruise control systemWindshield wiper switch673_066J533 is the LIN master for Multifunction Steering Wheel Control Module J453.Signals from the driver’s airbag and J453 are not processed by Steering Column Electronics Control Module J527.SC2SC9 Turn signal switch CCS switch Wipe/ wash switchSteering wheel Horn Steering wheel heating Airbag J453J527Spiral springJ519J623J234J533673_067SC2 SC9 J234 J453 J519 J527 J533 J623 Fuse 2 on fuse holder C Fuse 9 on fuse holder C Airbag Control Module Multifunction Steering Wheel Control Module Vehicle Electrical System Control Module Steering Column Electronics Control Module Data Bus On Board Diagnostic Interface Engine/Motor Control ModuleKey: LIN bus36 Interior lightingThere are three different equipment packages for the interior lighting. Different lighting colors can be selected with the optional contour/background lighting package.Standard equipment QQ0 Front roof modules1 Rear lighting2 Make-up lights Illuminated door pockets (front/rear) Contour lighting for front/rear doors Background fabric door panel lighting (front/rear)Background lighting package QQ1Contour/background lighting package QQ2RGBRGBEntry light (front)Interior door handle (front/rear) Door warning lamps Cup holder Background lighting for front center console Center console storage compartment (front) quattro badge or Audi rings4passive3passive3passive3RGBRGBRGBGlove box lightBBBRight luggage compartment lightKey: Unavailable LED lighting, whiteB RGBLighting with bulb Available in 10 colorsIncluding capacitive reading lights Including reading lights, mechanically operated via button 3 Passive means that only a reflector is installed 4 Right side, on instrument panel1 237 Digital instrument cluster 9SOThe Audi Q3 features a 10.25 inch digital display instrument cluster as standard. It houses Instrument Cluster Control Module J285 and is the immobilizer master. The instrument cluster is a network participant of the instrument cluster CAN and the MOST bus. J285 is a Terminal 30 control module and processes the signals from both fuel tank senders, the parking brake and data from the Anti-Theft Immobilizer Reader Coil D2Coolant temperature barsFuel gauge bars673_068Audi virtual cockpit 9S8The 2019 Audi Q3 can be equipped optionally with the Audi virtual cockpit (Pr. no.9S8). It offers additional features such as: displaying music tracks or large map images if Navigation plus is installed. Its screen size (seen diagonally) is 12.3” and has three different views, one of which is a new, particularly sporty display of the instrument cluster’s content.Coolant temperature barsFuel gauge bars673_069Illustration shows the 12.3” version38 Sensor-operated rear lid openingThe Q3 can be ordered with a sensor operated rear lid that opens with a foot gesture. The two sensor wires for Power Rear Lid Opening Sensor G750 and Power Rear Lid Opening Sensor 2 G760 are connected directly to Power Rear Lid Opening Control Module J938. J938 is a LIN participant of Access/Start Authorization Control Module J518. When a foot gesture has been made, J518 checks whether there is an authorized remote control key in the detection area. If the authorization is successful, rear lid opening is approved. This occurs irrespective of whether the vehicle is locked or unlocked.Rear Lid Control Module J605Power Rear Lid Opening Sensor 2 G760Power Rear Lid Opening Control Module J938673_070Power Rear Lid Opening Sensor G750Rear Lid Control Module J605 is a participant of the convenience CAN data bus.J938Terminal 31G750G760G750 G760 J518 J533 J605 J938 Power Rear Lid Opening Sensor Power Rear Lid Opening Sensor 2 Access/Start Authorization Control Module Data Bus On Board Diagnostic Interface Rear Lid Control Module Power Rear Lid Opening Control ModuleJ518J605Key: LIN bus Convenience CANJ533673_07139 Climate controlOverviewThere are no fundamental changes to the climate control refrigerant or air distribution systems when compared to the 2019 Audi Q3. A two-zone system is standard equipment. One new operational feature of the system is the control concept with the advent of the MMI touch response system. Some features may now be operated through the MMI screen. However, most personal settings for the vehicle’s climate control system are selected and adjusted via the relevant rotary controls and buttons located below the MMI display.Design of the climate control system2.0 ltr. TFSI engine with refrigerant R1234yfCool axial refrigerant lineExpansion valveService connection for low-pressure sideService connection for high-pressure sideHigh Pressure Sensor G65 Low-pressure line High-pressure line673_072Condenser and expansion tank with desiccant cartridgeA/C Compressor V454 with A/C Compressor Regulator Valve N28040 Overview of newly designed Audi Q3 instrument panel with MMI display, climate control and air outletsThe “Car” tile on the MMI display takes the user to the climate control settings. Depending on the vehicle equipment, the automatic air recirculation can be switched on there. The individual climate control settings such as AUTO, temperature selection, blower speed, air distribution, defrost mode for the windshield and side windows, air recirculation and rear window heating are selected/ adjusted directly via the relevant controls under the MMI display.Air outlet (driver side)Center air outlets MMI display (touch display) for general vehicle functionsAir outlet (passenger side)673_073Air conditioner controls (2-zone automatic climate control)Controls for 2-zone climate controlThe climate control system keeps the vehicle interior at a driver-chosen temperature automatically by regulating the temperature, volume and distribution of the air therein.In addition, the automatic air recirculation is regulated via air quality, sunlight and humidity sensors.The 2-zone automatic air conditioner controls have the following functions: ›› Rotary temperature controls, front left and right seats can be adjusted separately ›› A/C on/off button ›› AUTO button ›› Rotary control for blower speed ›› Air distribution button (footwell, center and upwards)41›› ›› ›› ››Windshield defrost mode button Air recirculation mode button Rear window heating button Seat heating buttons (left and right) 42 Safety and driver assist systemsPassive safetyThe following pages provide an overview of the occupant protection system in the Audi Q3.AirbagsDriver airbagPassenger airbagKnee airbag for driver and passenger sideFront side airbagComponents›› ›› ›› ›› ›› ›› ›› ›› ›› ›› ›› ›› Airbag control module Adaptive driver airbag Adaptive passenger airbag (two-stage passenger airbag) Front side airbags Side airbags for seat row 2 Curtain airbags Knee airbags Crash sensors for front airbags Crash sensors for side impact detection in doors Crash sensors for side impact detection in C-pillars Front belt retractors with pyrotechnic belt tensioners Front belt retractors with electric belt tensioners ›› Front belt retractors with switchable belt force limiters ›› Belt retractors for seat row 2 with pyrotechnic belt tensioners for driver and passenger side ›› Front lap belt tensioners for driver and passenger sides ›› Seat belt warning for front seats ›› Seat-occupied recognition system in passenger seat ›› Battery interrupt igniter, 12 Volt electrical system43 Front side airbagHead airbag for driver and passenger sideSide airbag for seat row 2673_076Side airbag for seat row 2!Note The images in the “Passive safety” chapter are schematic diagrams and are provided to aid understanding.44 System overviewG553673_07745 Key to figure of System overview :E24 E25 G128 G179 G180 G256 G257 G283 G284 G551 G552 G553 G554 J234 J285 J533 J706 J854 J855 K19 K75 K145 Driver Seat Belt Switch Front Passenger Seat Belt Switch Passenger Seat Occupant Detection Sensor Driver Thorax Airbag Crash Sensor Front Passenger Thorax Airbag Crash Sensor Driver Side Rear Thorax Airbag Crash Sensor Passenger Side Rear Thorax Airbag Crash Sensor Driver Front Airbag Crash Sensor Passenger Side Front Airbag Crash Sensor Driver Belt Force Limiter Front Passenger Belt Force Limiter Driver Seat Position Sensor Front Passenger Seat Position Sensor Airbag Control Module Instrument Cluster Control Module Data Bus on Board Diagnostic Interface Passenger Occupant Detection System Control Module Left Front Seat Belt Tensioner Control Module Right Front Seat Belt Tensioner Control Module Seat Belt Indicator Lamp Airbag Indicator Lamp Front Passenger Airbag -Disabled- Indicator Lamp (both ON and OFF status of passenger airbag is indicated)N95 N131 N132 N153 N154 N196 N197 N199 N200 N201 N202 N251 N252 N253 N295 N296 N297 N298 N490 N491 T16 Driver Airbag Igniter Front Passenger Airbag Igniter 1 Front Passenger Airbag Igniter 2 Driver Seat Belt Tensioner Igniter 1 Front Passenger Seat Belt Tensioner Igniter 1 Driver Side Rear Seat Belt Tensioner Igniter Passenger Side Rear Seat Belt Tensioner Igniter Driver Thorax Airbag Igniter Front Passenger Thorax Airbag Igniter Driver Side Rear Thorax Airbag Igniter Passenger Side Rear Thorax Airbag Igniter Driver Head Curtain Airbag Igniter Front Passenger Head Curtain Airbag Igniter Battery Interrupt Igniter Driver Knee Airbag Igniter Front Passenger Knee Airbag Igniter Driver Seat Belt Tensioner Igniter 2 Front Passenger Seat Belt Tensioner Igniter 2 Driver Airbag Release Valve Igniter Front Passenger Airbag Release Valve Igniter Data Link ConnectorKey: Diagnostics CAN LIN bus Convenience CAN Powertrain CAN Input signal Output signalConnection for Passenger Seat Occupant Detection Sensor G128In vehicles for the North American region (NAR): G128 is connected to Passenger Occupant Detection System Control Module J706 via a discrete wire. It communicates with Airbag Control Module J234 via a LIN.46 Active safetyAudi pre senseAudi pre sense basic and pre sense front are standard on all Q3 models.Driver Assistance Systems Front Camera R242673_078Control Module for Adaptive Cruise Control J428It has the following features compared to other Audi models: ›› If the ESC (electronic stabilization control) system is switched to “offroad” using ASR/ESP Button E256, Audi pre sense front remains available. ›› The system is capable of detecting cyclists and react to them. ›› It can detect pedestrians and cyclists moving in the same direction as the vehicle as well as pedestrians and cyclists who are crossing the vehicle’s path. ›› The symbol for the visual pre-warning/intervention display has been standardized so it corresponds to other Audi vehicles, such as the 2019 Audi A8.Visual pre-warning/ intervention display673_07947 Driver assist systemsThe following systems and functions are detailed in the next pages: ›› ›› ›› ›› ›› ›› ›› Top view camera system Rear cross-traffic assist Hands-off detection Lane departure warning Adaptive cruise control Audi side assist Speed limiterTop view camera systemFor the first time, a top view camera system is available for the Audi Q3. The cameras help customers when they are maneuvering and parking the vehicle. The peripheral view camera function allows an image of the vehicle from above to be displayed. At speeds of up to 6.2 mph (10 km/h), it shows the immediate surroundings of the Audi Q3 on the MMI displays. The user can switch between various views. Along with the virtual view from above, the back-up camera view and the 180° panorama view (front and rear), there is a detailed view of the front and rear wheels. This helps to avoid rim damage. It is also possible to display the wheels (either the front or rear wheels as pairs).Right Peripheral Camera R245Peripheral Camera Control Module J928673_080Front Peripheral Camera R243Left Peripheral Camera R244Rear Peripheral Camera R246Calibration The camera calibration process is the same as on other similarly equipped Audi models using calibration mats VAS 721 001. The advantage of this calibration procedure is that the four cameras can be calibrated quickly and all at once.673_08148 Rear cross-traffic assistDescription of function The rear cross-traffic assist can warn the driver of a possible cross-traffic collision when backing up. With the help of the radar sensors, the system monitors the vehicle’s rear side surroundings. Objects, such as cars approaching from the side at the rear, can be detected. However, if they approach very quickly, they may not be detected in time. The system reacts to both pedestrians and cyclists if it detects them. The two rear radar sensors are installed in the rear bumper (left and right).Requirements ›› The system must be activated via the MMI. ›› Reverse gear must be selected and the vehicle speed must not be greater than 6.2 mph (10 km/h).Illustration of detection area of rear radar sensors673_082Functions of rear cross-traffic assist If an approaching vehicle is detected when the vehicle is backing up, the following warnings are given: ›› An arrow from the direction of the approaching vehicle is shown on the MMI display. The arrow is only visible if the image from the rear peripheral camera or the top view camera is currently displayed. The parking aid must also be activated. ›› Acoustic signal, made as a continuous tone. ›› Automatic brake jolt if no driver reaction has yet been detected. Lane Change Assistance Control Modules J769 and J770 are responsible for the cross traffic assist function. J769 is the master control module and is installed behind the bumper cover on the right hand side of the vehicle.Lane Change Assistance Control Module 2 J770673_083Lane Change Assistance Control Module J769Lane Change Assistance Control Module 2 J770673_084!49Note If the indicator lampsor a crossed-through arrow are shown as driver messages, the system is unavailable. Hands-off detectionBy evaluating the steering torque sensor, the system can draw conclusions to whether the driver’s hands are on the steering wheel or not. Hands-off detection when lane departure warning is active When the lane departure warning is switched on and active, hands-off detection is only active at the moment of the steering intervention. No hands-off detection is performed if no intervention is required to keep the vehicle in its lane.Lane departure warningNew feature With the previous assist system (Audi active lane assist), the driver could select “early” or “late” steering input. Because the functions have been redistributed, these settings are no longer present. The steering input setting “late” from the Audi active lane assist is now the lane departure warning.R242 Driver Assistance Systems Front CameraDescription of function The lane departure warning helps drivers stay in their lane. This is possible because Driver Assistance Systems Front Camera R242 can detect lane markings. If the vehicle nears a detected lane marking and is at risk of leaving its lane, the system warns the driver with a correcting steering input and may also vibrate the steering wheel. This happens if a lane change is made without using the turn signals. The system operates at speeds above approximately 40 mph (65 km/h). If the turn signal is on when a lane marking is crossed, the system does not intervene as it assumes that the lane change is intended. If the side assist system is active in addition to the lane departure warning, increased steering torque is used to warn the driver and avoid an impending collision. This warning is given if the turn signal is on and the system has detected a danger from the rear or in the blind spot.673_086!Note At speeds of approximately 6.2 mph (10 km/h) and below, the hands off detection may work slowly or not at all.50 The lane departure warning is activated/deactivated via the button on the end of the turn signal lever. However, both the lane departure warning and the lane assist are activated/deactivated when the button is pressed. The system is always active if the ignition is switched off and then on again. This means that the lane departure warning can only be deactivated for one driving cycle. The steering wheel vibration can be switched on and off. This setting remains in place after the ignition is switched off and on again.Button for activating lane departure673_085Meaning of displays The lane departure warning is on, but not ready to give warnings.673_087The lane departure warning is on and currently only able to give warnings on the right.673_088The vehicle is at risk of leaving its lane on the left. A steering intervention is currently being made along with, possibly, a steering wheel vibration.The lane departure warning is ready to give warnings if at least one lane marking is detected. In this case, the system will only intervene on that side. The system is passive if: ›› The turn signal is on. ›› The activation speed of approximately 40 mph (65 km/h) has not been reached. ›› The driver’s steering activity is too high. ›› The lane departure warning previously made two hands-off inputs. ›› No lane has been detected.673_089If the system does not detect lanes, it may be for the following reasons: ›› ›› ›› ›› ›› The lane is either too narrow or too wide. The lane is dirty. Snow or moisture are preventing detection. Road work is preventing detection. The camera is restricted due to glare or oncoming lights.!51Note If an indicator lamp (white or yellow vehicle with lane markings) is shown as a driver message when the driver attempts to activate the lane departure warning, the system is not available. The reason is also shown in text form. System status, description, displays and symbols for the lane departure warningSystem statusDescriptionDisplaysSymbolsOFFNo displayONBoth lane markings not detected or system is currently passive.ONBoth lane markings detected.ONRight lane marking detected, warnings can therefore only be given for right, no intervention.ONBoth lane markings detected. Steering intervention on right side as vehicle is at risk of leaving lane on right.ONOnly right lane marking detected. Steering intervention on right side as vehicle is at risk of leaving lane on right.Warnings If a lane departure warning intervention lasts longer than 10 seconds, the driver’s attention is drawn by a tone and the message “please drive in the middle of the lane”. This may occur when driving through a long corner.52 Display concept for lane departure warningDriver assist display Lines off/white/green/redFunction symbol display Lines off/white/green/redLane departure warningUnavailableDriver assist systemsAudi side assistAudi side assist monitors traffic approaching from behind the vehicle and the blind spot. If the driver intends to change lane, the system warns if a collision risk is detected. The warning is given by a bright flashing light in the exterior mirror housing. The rear radar sensors are known as midrange sensors. Mid-range sensors have a range of approximately 76.5 yd (70 m). Long-range sensors have a range of approximately 219 yd (200 m). Short-range sensors have a range of a few yards. The following control modules are responsible for the lane change warning in the Audi Q3: ›› Lane Change Assistance Control Module J769 ›› Lane Change Assistance Control Module 2 J770Active warning Audi side assist in left exterior mirror673_096Limitation The rear radar sensors do not provide an exit warning feature in the Audi Q3. The exit warning system function from the MLB platform has not been implemented for MQB vehicles. Vehicles on this platform have rear radar sensors, but not the exit warning system. Rear radar sensors on MLB platform vehicles are supplied with power directly from Terminal 30 (battery). This is not the case on the MQB platform; the control modules are participants of Terminal 15. The control modules are not energized when the ignition is switched off. As a result, it is not possible to implement the exit warning system. MQB platform:673_090The Audi A3 and Q3 are vehicles of the modular transverse matrix. On these vehicles, the engine is installed transversely (at right angles to the direction of travel).53 Adaptive cruise controlDescription of function The adaptive cruise control regulates both the vehicle’s speed and its distance to the vehicle in front. The system brakes or accelerates depending on how the vehicle detected ahead is being driven. If no vehicle is detected, the function works like a conventional cruise control system, meaning that the set speed is kept constant insofar as the laws of physics and regulation accuracy allow. The vehicle can be brought to a halt and also set in motion again. However, the brake must be held to ensure that the system remains active, otherwise it is switched off after approximately 3 seconds.Operation The system is operated via the ACC operating lever, as on the previous systems (cruise control system and adaptive cruise control).Radar sensor New feature for the 2019 Audi Q3: ›› The time gaps used for setting the distance warning have been changed/increased.673_091Lane Change Assistance Control Module J428 and Right Adaptive Cruise Control Sensor G259!Note For safety reasons, the adaptive cruise control is only active if the driver’s seat belt is fastened and all the doors and the hood are closed. If the vehicle comes to a standstill for a few seconds, the adaptive cruise control is also not active.54 Infotainment and Audi connectIntroduction and overview of versionsThe Audi Q3 features the MIB2+ version of the modular infotainment matrix infotainment system. Customers can choose between two MMI versions: ›› MMI radio plus ›› MMI navigation plus The MMI radio plus and MMI navigation plus are both MIB2+ High devices. The two systems can be distinguished in the following ways: ›› The MMI radio plus is equipped with an 8.8” display as standard. ›› The MMI navigation plus system has a 10.1 inch display and features 3D navigation.MMI radio plus (I8V + 7Q0)MMI navigation plus (I8T + 7UG)RADIOMEDIACARRADIOMEDIATELEPHONESHORTCUTSSHORTCUTSSETTINGSTELEPHONEUSERSHELPCARSETTINGS8.8” touch display with 1280 x 720 pixels Digital instrument cluster (9S0)10.1” touch display with 1540 x 720 pixels Audi virtual cockpit (9S1)1 3D navigation system